advertisement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1)This device may not cause harmful interference, and
(2)This device must accept any interference received, including interference that may cause undesired operation.
Note:
This equipment has been tested and found to comply with the limits for Class B digital devices, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna
Increase the separation between the equipment and receiver
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
Consult the dealer or an experienced radio/TV technician for help
Use of shielded cable is required to comply with Class B limits in Subpart B of Part 15 of the FCC rules.
Do not make any changes or modifications to the equipment unless otherwise specified in the manual.
If such changes or modifications should be made, you could be required to stop operation of the equipment.
1
Microsoft
®
and Windows
®
are U.S. registered trademarks of Microsoft Corporation.
Pentium
®
is a registered trademark of Intel Corporation.
Macintosh is a trademark of Apple Computer, Inc.
SD
TM
is a trademark.
PhotoSuite, PhotoVista are trademarks.
Other names and products may be trademarks or registered trademarks of their respective owners.
E
F
G
S
2
Notice:
1. Product design and specifications are subject to change without notice. This includes primary product specifications, software, software drivers, and user’s manual. This User Manual is a general reference guide for the product.
2. The product and accessories that come with your camera may be different from those described in this manual. This is due to the fact that different retailers often specify slightly different product inclusions and accessories to suit their market requirements, customer demographics, and geographical preferences. Products very often vary between retailers especially with accessories such as batteries, chargers, AC adapters, memory cards, cables, carrying cases/pouches, and language support.
Occasionally a retailer will specify a unique product color, appearance, and internal memory capacity.
Contact your dealer for precise product definition and included accessories.
3. The illustrations in this manual are for the purpose of explanation and may differ from the actual design of your camera.
4. The manufacturer assumes no liability for any errors or discrepancies in this user manual.
Warnings
Do not expose the camera to moisture and make sure no water gets into the camera. Take particular care when using the camera under extreme weather conditions, such as rain or snow, or when operating the camera at the beach on near water. Avoid using this camera in places subject to extreme moisture.
Do not use the camera if water has entered the camera. Turn the camera off, remove the batteries, and disconnect the power source if you are using an AC power adapter. Unplug the adapter from the
AC power outlet after you have disconnected the camera. Contact your dealer or authorized service facility. Do not continue to use the camera as this may cause a fire or an electrical shock.
Do not touch the power plug during a thunderstorm if you are using the AC power adapter. This may cause an electrical shock.
Do not use the camera if any foreign objects have entered the camera. Turn the camera off, remove the batteries, and disconnect the power source if you are using an AC power adapter. Unplug the adapter from the AC power outlet after you have disconnected the camera. Contact your dealer or authorized service facility. Do not continue to use the camera as this may cause a fire or an electrical shock.
Do not place the camera in an unstable location such as on a wobbly table or sloping surface where the camera may fall or tip over and cause injury. If the camera has been dropped or damaged, turn the camera off and remove the batteries or AC power adapter. Contact your dealer or authorized service facility. Do not continue to use the camera as this may cause a fire or an electrical shock.
3
F
G
E
Warnings
Do not attempt to modify this camera. Do not remove the camera casing. This may cause a fire or an electrical shock. Internal inspection and repairs should only be carried out by an authorized service facility.
Never operate this camera in any way while driving a vehicle. This may cause a traffic accident.
Do not cover or wrap the camera or the AC power adapter with a cloth or quilt. This may cause heat to build up, distort the case and cause a fire. Always use the camera and its accessories in wellventilated locations.
Do not move the camera while it is switched on. (If you are using the AC power adapter, unplug the adapter from the AC power outlet after you have switched off the camera.) Ensure that any connector cords or cables to other devices are disconnected before moving the camera. Failure to do so may damage the cords or cables and cause a fire or an electrical shock.
S
4
7 Introduction
7
8
Overview
Package Contents
9 Components Guide
9 Front View
10 Rear View
11 Control Panel
12 Mode Dial
13 Viewfinder LED Indicators
14 LCD Monitor Information
18 Preparing Your Camera
18 Installing the Batteries (Optional Accessory)
19 Using an AC Power Adapter (Optional
Accessory)
20 Installing an SD Memory Card (Optional
Accessory)
21 Setting the Language
22 Setting the Date and Time
22 Attaching the Camera Strap
30 Photography Mode
30 Auto Mode
31 Scene Mode
33 Manual Mode
34 Video mode
35 Program AE Mode
35 Shutter Speed Priority Mode
36 Aperture Priority Mode
37 Photography–Selecting Particular Effects
37 Changing Image Resolution and Quality
39 Adjusting the Exposure Compensation
40 Setting the White Balance
41 Switching between Metering Modes
42 Replaying
42 Single Image Replay
43 Recording Voice Memos
44 Magnifying Images
45 Thumbnail Display
46 Viewing Video Clips
47 Automated Playback (Slide Show)
48 Protecting Images/Video Clips
23 Basic Functions
23 Turning the Power On
24 Using the LCD Monitor
25 Using the Optical Viewfinder to Shoot
26 Adjusting the Zoom
27 Using the Self-Timer
28 Using the Flash
49 Erasing
49 Deleting Images/Video Clips Singly
50 Deleting All Images/Video Clips
51 Formatting an SD Memory Card or
Internal Memory
5
E
52 Print Settings (DPOF Settings)
53 Transferring Recorded Images/Video
Clips To Your Computer
57 Installing PhotoSuite
58 Installing PhotoVista
59 List of Menu Options
59 Capture Menu
64 Playback Menu
68 Video Menu
69 Setup Menu
72 Connecting Your Camera To Other
Devices
73 Camera Specifications
F
G
S
6
Your new stylish digital camera delivers high quality, 2272 x 1704 resolution images using a 4.0 Megapixels
CCD sensor. Using either the optical viewfinder or the 1.5" LTPS TFT color image LCD monitor, you can compose images and then examine them in detail. An auto-flash sensor automatically detects the shooting (lighting) conditions and determines whether the flash should be used. This feature helps ensure that your images turn out right.
16MB internal (built-in) memory let you capture and store images without the need for an additional memory card. However, you may wish to expand the memory capacity by using an external memory card.
In addition to still images, you can record short videos by using the movie function.
Images you have taken can be downloaded to your computer using the USB cable (USB driver is required for Win 98 and Mac OS 8.6). You can enhance and retouch your images on your computer by using the provided editing software, or image editing software you may already own. You may share your images with your friends via e-mail, in a report, or on a website.
DPOF functionality allows you to print your images on a DPOF compatible printer by simply inserting the memory card.
7
E
Carefully unpack your camera and ensure that you have the following items.
Common Product Components:
Digital Camera
A/V Cable
User’s Manual
USB Cable
Software CD-ROM
Camera Strap
Camera Pouch
Common (Optional) Accessories:
SD Memory Card
AC Power Adapter
Batteries
F
G
S
8
1. Zoom controller
2. Shutter button
3. Power button
4. Flash
5. Viewfinder window
6. Lens
7. Microphone
8. Self-timer LED
9
E
F
G
S
1. Viewfinder
2. LED indicator
3. LCD monitor
4.
Menu button
5.
Playback button
(Capture Playback)
6. Control panel
7. Mode dial
10
8. Strap eyelet
9. Battery/SD card cover
10. USB/ A/V Out terminal
11. DC IN jack
12.
Delete button
13. Tripod socket
1.
2.
Up button
Scene mode switch
(under Scene mode)
Shutter speed or Aperture switch
(under
M/Av/Tv
mode)
Rotate the image 90
0
to the left (under [ ] mode)
Right button
Self-timer button
3.
OK
OK button
4.
Down button
Scene mode switch
(under Scene mode)
Shutter speed or Aperture switch
(under
M/Av/Tv
mode)
Rotate the image 90 0 to the right (under [ ] mode)
5.
Left button
Flash button
11
E
F
G
1. [
2. [
A
]
3. [
P
]
]
Mode
Video mode
Auto mode
Program mode
4. [
SCENE
] Scene mode
5. [
M
] Manual mode
6. [
Av
]
7. [
Tv
]
Aperture Priority mode
Shutter Speed Priority mode
8. [ ] Setup mode
Description
Select this mode to record video (movie) clips.
Select this mode to adjust “point-and-shoot” action.
This mode permits the shutter speed and aperture to be set automatically and other factors to be set manually.
Select this mode to match the occasion or situation.
Select this mode to take still images by manual adjustments.
Select this mode when you want your image(s) with aperture priority.
Select this mode when you want your image(s) with shutter speed priority.
Select this mode to adjust the camera settings.
S
12
–
–
Indicator
LED indicator
LED indicator
LED indicator
LED indicator
LED indicator
LED indicator
LED indicator
Self-timer indicator
Status
Solid red
Solid green
Blinking red
Description/Activity
The camera is powering up
The camera is powered and ready
Camera error
Blinking red Charging the flash
Blinking green Image is being recorded to the memory card
Blinking green USB communication/transfer in progress
Solid green The camera is ready to record images (or movies)
The self-timer function is activated Blinking
Self-timer LED
Blinking red
–
Error message
Valid button event
13
Capture Mode:
E
F
G
S
1. Mode indication
[ ] Video mode icon
[
A
] Auto mode icon
[
PRG
] Program mode icon
Scene mode [ ] Landscape mode icon
Scene mode [ ] Portrait mode icon
Scene mode [ ] Sports mode icon
Scene mode [ ] Night Scene mode icon
Scene mode [ ] Backlight mode icon
Scene mode [ ] Pan mode icon
[
M
] Manual mode icon
[
Av
] Aperture Priority mode icon
[
Tv
] Shutter Speed Priority mode icon
[ ] Setup mode icon
2. Zoom state
14
3. White balance
(no indication for auto white balance)
AUTO
[ ]DAYLIGHT
[ ]CLOUDY
[ ]SUNSET
[ ]TUNGSTEN
[ ]FLUORESCENT
4. Flash mode
[
A
] Automatic flash
[
A
] Red-eye reduction
[ ] Fill flash (on)
[ ] Flash off
5. Image size
[ ] 2272 x 1704
[ ] 1600 x 1200
[ ] 1280 x 960
[ ] 640 x 480
6. [ ] Card indicator
7. [ ] Self-timer indicator
8. [ ] Histogram indicator
9. Remaining number of shots
10. Power supply
[ ] Full battery power
[ ] Medium battery power
[ ] Low battery power
[ ] Virtually no battery power
[ ] Adapter indicator
11. Aperture priority indication
12. Shutter speed indication
13. Focus indicator
(no indication for auto focus)
AUTO
[ ] MACRO
[ ] 1M
[ ] 3M
[ ] INFINITY
14. Capture mode indicator
(no indication for single image capturing)
SINGLE
[ ] MULTI
[ ] BURST
[ ] AEB
15
E
F
G
S
Video Mode:
1. Recording indicator
2. Video counter
3. [ ] Video mode icon
4. [ ] Card indicator
5. Power supply
[ ] Full battery power
[ ] Medium battery power
[ ] Low battery power
[ ] Virtually no battery power
[ ] Adapter indicator
Playback Mode: (Still Images)
1. [ ] Card indicator
2. Forward key
3. [ ] DPOF icon
4. Current image number / total number of images
5. [ ] Protect indicator
6. Power supply
[ ] Full battery power
[ ] Medium battery power
[ ] Low battery power
[ ] Virtually no battery power
[ ] Adapter indicator
7.
Voice memo
8. Reverse key
16
8
Playback Mode: (Video Clips)
1. Elapsed playback indicator
2. Elapsed time
3. Playback mode
4. [ ] Card indicator
5. Power supply
[ ] Full battery power
[ ] Medium battery power
[ ] Low battery power
[ ] Virtually no battery power
[ ] Adapter indicator
17
You can use 2 AA size batteries to power the camera. Battery power is convenient for capturing images or recording video clips.
1. Make sure your camera is off.
2. Slide the battery/SD card cover lock.
3. Insert the batteries according to the correct polarity marks (+ or -).
4. Close the battery/SD card cover lock firmly.
E
F
G
S
18
You may use a CR-V3 Lithium battery pack.
Avoid using batteries in extremely cold environments as low temperatures can shorten the battery life and reduce camera performance. This low temperature will also influence Alkaline battery performance, therefore Ni-MH rechargeable battery is highly recommended.
If you are using the new rechargeable batteries or rechargeable batteries that have not been used for an extended period of time (batteries that pass the expiry date are exceptions) might affect the number of pictures that can be taken. Therefore, to maximize their performance and lifetime, we recommend that you fully charge the batteries and discharge them for at least one complete cycle before use.
If you will not be using the batteries for an extended period of time, remove them from the camera to prevent leakage or corrosion.
Never use batteries of different types (together) or mix old and new batteries.
Never use manganese batteries.
There’s also another way to power your camera–using an AC power Adapter. AC power adapter is recommended for long periods of continuous use or for transferring images to your computer.
1. Make sure your camera is off.
2. Open the port cover and connect one end of the AC power adapter to the jack labeled “DC IN”.
3. Connect the other end to an electrical outlet.
Make sure to use only the AC power adapter specified for the camera. Damage caused by the use of an incorrect adapter is not covered under the warranty.
To prevent unexpected auto power off resulting from no battery power left during the process of transferring your images to the computer, use the AC power adapter as a power supply.
The AC power adapter can only be used to power the camera. Batteries cannot be charged inside the camera.
19
E
Your camera comes with 16MB of internal memory, allowing you to store images and video clips in the camera. However, you can also expand the memory capacity by using the SD memory card. Optional
SD memory card provide removable, reusable storage for images and video clips.
1. Make sure your camera is off.
2. Slide the SD card/battery cover lock.
3. Insert the SD memory card.
If the card cannot be inserted, check the orientation.
4. Close the SD card/battery cover lock firmly.
To remove an SD memory card
1. Make sure your camera is off.
2. Slide the SD card/battery cover lock.
3. Press lightly on the edge of the memory card and it will eject.
F
G
S
20
To prevent valuable data from being accidentally erased from an SD memory card you can slide the write protect tab (on the side of the SD memory card) to “LOCK”.
To save, edit, or erase data on an SD memory card, you must unlock the card.
To fully capture all images you want, be sure to reformat first your SD memory card.
Be sure to format an SD memory card by this camera before using it.
Not all SD memory cards are compatible for this camera. We highly recommend to use Panasonic, Toshiba and
SanDisk memory cards to demonstrate the camera’s performance.
Specify in which language menus and messages are to be displayed on the LCD monitor.
Follow the steps below to set the OSD (On-Screen Display) language.
1. Set the mode dial to [ ].
2. Select “LANGUAGE” by using the / button, and press the
button.
3. Select the displayed language by using the / button, and press the button.
4. To exit the menu, change the mode dial setting.
The language setting will be retained even if the camera is turned off.
The provided languages are [ENGLISH], [FRAN
ç
AIS], [DEUTSCH], [ESPAÑOL], [ITALIANO], [
[ ].
] and
21
E
F
The Date/Time screen will be presented if/when:
The camera is turned on for the first time.
The camera is turned on after removing the batteries/AC power adapter for a long period of time or replacing the batteries.
When the date and time setting screen appears, follow these steps to set the correct date and time.
You may also skip this procedure by selecting
EXIT
option and press the button
1. Select the “DATE” or “TIME” option by using the / button and press the button.
2. Select the item’s field by using the / button and adjust the value for the date and time by using the / button.
The date default setting is set in the order day-month-year.
3. After confirming all settings are correct, press the button.
4. Select the “MODE” option by using the / button and press the
button.
5. Select the “MODE” type by using the / button and press the button.
6. Select “EXIT” by using the / button and press the button.
The setting will be stored and the screen will return to the capture mode.
G
S
To prevent accidental slippage during the use, always use the camera strap.
Attach the camera strap as follows:
1. Thread the small loop of the strap through the strap eyelet on the camera.
2. Pull the large loop through the small loop until the strap is firmly
22 secured.
1. Press the
POWER
button.
The LED indicator is lit red and the camera is initiated.
With lens opened Photography mode
With the PC connected PC mode
Turning the Power Off
With the power on, press the
POWER
button again to turn the camera off.
23
E
Using the LCD monitor can help you to confirm an image while taking pictures, to replay recorded images/video clips or to adjust menu settings.
The mode icons, text and numbers that are displayed on the LCD monitor may vary according to the current settings.
1. Rotate the mode dial based on your desired scenery (Video/Auto/
Program/Scene/Manual/Av/Tv) and power on your camera.
2. Compose your image in the LCD monitor.
3. Press the shutter button.
F
G
S
24
In the Capture mode, toggling the button will set OSD On, OSD Off and Display Off.
The LCD monitor darkens in strong sunlight or bright light. This is not a malfunction.
Using the LCD monitor for an extended period of time will decrease the number of images you can take. To conserve battery power and increase the number of pictures you can take, we recommend you to turn the LCD monitor off and use the viewfinder instead.
In [ ] Video mode LCD monitor can be turned off. However, in Playback mode the LCD monitor cannot be turned off.
Your camera is also equipped with an optical viewfinder to compose images. Using the viewfinder helps you to compose images and adjust the subject in the crisp focus. Taking images by using the optical viewfinder will conserve more battery power. We recommend you to use the viewfinder when your batteries’ level is in low condition.
1. Rotate the mode dial based on your desired scenery (Video/Auto/
Program/Scene/Manual/Av/Tv) and power on your camera.
2. Compose your image in the viewfinder.
3. Press the shutter button.
The LED indicator blinks green while the camera is processing a captured image.
25
E
The lens moves during the zoom photography. Zoom photography allows you to capture telephoto and wide-angle images. The subject appears closer by sliding the zoom controller towards [
T
] and appears farther away by sliding the zoom controller towards [
W
].
1. Rotate the mode dial based on your desired scenery (Video/Auto/
Program/Scene/Manual/Av/Tv) and power on your camera.
2. Compose your image by sliding the zoom controller left or right.
Slide the zoom controller towards [
T
] to its maximum position.
Slide it again to activate the digital zoom function.
Slide repeatedly the zoom controller towards [
T
]. Digital zoom's range is from 1.2x to 4.0x within 10 stages: 1.2x, 1.4x, 1.6x, 1.8x,
2.0x, 2.4x, 2.8x, 3.2x, 3.6x, 4.0x.
To exit the digital zoom, slide repeatedly the zoom controller towards [
W
] until it returns to the optical zoom status.
3. Press the shutter button to capture a “zoomed” image.
F
Digital zoom cannot be used in [ ]Video mode.
G
S
26
This setting enables images to be taken with the [ ] self-timer.
The [ ] self-timer button can select the capturing mode between “Off” (default) and “Self timer”
(5 seconds, 10 seconds or 10+2 seconds).
[5 SEC]: Your camera automatically takes a picture after five seconds delay.
[10 SEC]: Your camera automatically takes a picture after ten seconds delay.
[10+2 SEC]: Your camera automatically takes a picture after ten seconds delay, and takes another picture again after two seconds.
1. Secure the camera to a tripod or place it on a stable surface.
2. Rotate the mode dial based on your desired scenery (Video/Auto/
Program/Scene/Manual/Av/Tv) and power on your camera.
3. Compose your image.
4. Press [ ] the self-timer button.
5. Press the shutter button.
The count down is displayed on the LCD monitor.
When you toggle the self-timer button, the following are displayed in the accordingly order:
Off 5 SEC 10 SEC 10+2 SEC
To cancel the self-timer photography at any time, press the [ ] self-timer button to disrupt the sequence.
When selecting the [10+2 SEC] as the self-timer photography mode, the digital zoom can not be activated.
27
E
The flash is designed to function automatically when lighting conditions warrant the use of flash. You can take an image using a suitable flash mode to your circumstances.
1. Rotate the mode dial based on your desired scenery (Video/Auto/
Program/Scene/Manual/Av/Tv) and power on your camera.
2. Press the [ ] flash button located on the rear side of the camera repeatedly until your desired flash mode appears on the LCD monitor.
When you toggle the [ ] flash button, the following are displayed in the accordingly order:
[
A
] Automatic flash [
A
] Red-eye reduction [ ] Fill flash (on) [ ] Flash off
3. Compose your image and press the shutter button.
F
G
S
28
The table below will help you to choose the appropriate flash mode:
Flash Mode
[
A
] Automatic flash
[
[ ]
[
A
] Red-eye reduction
Fill flash (on)
] Flash off
Description
The flash fires automatically according to the ambient lighting conditions.
Select this mode for general photography.
The flash emits a precursor-flash before the main flash fires. This causes the pupil in the human eye to constrict, reducing the red-eye phenomenon.
Select this mode when taking images of people and animals in low-light conditions.
The flash will always fire regardless of the surrounding brightness.
Select this mode for recording images with high contrast (backlighting ) and deep shadows.
The flash will not fire.
Select this mode when taking images in a place where flash photography is prohibited, or when the distance to the subject is beyond the effective range of the flash.
In [ ] Macro mode and [ ] Landscape mode, flash photography is not possible.
In [ ] Night Scene mode, flash photography is fixed to [ ] Fill Flash (on).
In [ ] Backlight mode, flash photography is fixed to [ ] Fill Flash (on).
In [ ] Video mode, flash cannot be set.
29
E
Using [
A
] Auto mode the majority of the settings are adjusted by the camera. Simply point the subject and then shoot.
1. Rotate the mode dial to [
A
] Auto mode and power on your camera.
2. Aim the camera at your subject.
3. Press the shutter button.
F
G
S
30
Scene Mode [
SCENE
]
This sets the scene setting such as [ ] Landscape, [ ] Portrait, [ ] Sports, [ ] Night Scene, [ ]
Backlight or [ ] Pan and takes the photograph.
1. Rotate the mode dial to [
SCENE
] Scene mode and power on your camera.
2. Toggle the / button to select the desired scene mode.
When the scene mode is set to [ ] Landscape, [ ] Portrait, [ ]
Sports, [ ] Night Scene, [ ] Backlight or [ ] Pan, [ MACRO ] setting cannot be selected.
3. Aim the camera at your subject.
4. Press the shutter button.
31
E
F
The table below will help you choose the appropriate scene mode:
Scene Mode
[ ] Landscape
Description
Select this when you want to shoot expansive landscape scenes or when shooting scenery or landscapes through a glass window.
[ ] Portrait
[ ] Sports
The flash mode is fixed to [ ] Flash Off.
Select this when you want to take a photograph that makes the person stand out and blurs the background.
Select this when you want to photograph fast-moving subjects.
[ ] Night Scene Select this when you want to photograph people with an evening or night scene background.
[ ] Backlight
[ ] Pan
The flash mode is fixed to [ ] Fill Flash (On).
Select this when the subject is darker than the surrounding scene, or when you are taking photographs in a shadowed area, or when the light source is in back of your subject.
The flash mode is fixed to [ ] Fill Flash (On).
Select this when you do not want to miss a shot, but you cannot predetermine the subject’s position or focal distance. The focal length is preset to the maximum wide-angle setting. This mode fixes the focus so that shot can be taken quickly when the shutter button is pressed.
G
The description of each scene serves as a general guide. Set the camera to suit your own preferences.
S
32
You can take pictures by manually adjusting the camera settings. The flash default setting for [
M
]
Manual mode is [ ] flash off. For long time exposure photography, be sure to set the flash setting to
[ ] flash off.
1. Rotate the mode dial to [
M
] Manual mode and power on your camera.
2. Aim the camera at your subject.
3. Press the shutter button.
You can set the shutter speed by using the button, and aperture value by using the button.
33
E
Using [ ] Video mode you can record video clips at a resolution of
256 x 192 pixels. Voice can also be recorded.
1. Rotate the mode dial to [ ] Video mode and power on your camera.
2. You can start recording a video clip by pressing the shutter button.
The elapsed time displays on the LCD monitor while recording a video clip.
The recording time depends on the storage size and the subject of the images to be recorded.
3. To stop recording, press the shutter button again.
In [ ] Video mode, digital zoom cannot be activated; however, optical zoom can be used before composing.
Be sure not to cover the camera’s microphone while recording video clips.
F
G
S
34
Using the Program (Automatic Exposure) the camera automatically sets the shutter speed and the aperture to match the brightness of the scene.
1. Rotate the mode dial to [
P
] Program.
2. Power on your camera.
3. Compose your picture.
4. Press the shutter button.
When you set the shutter speed mode, the camera automatically selects an aperture setting to match the image’s brightness. Faster shutter speeds let you catch an instantaneous image of a fast-moving subject while slower speeds create a flowing impression letting you capture images without a flash in dark areas.
The flash default setting for [
Tv
] Shutter Speed Priority mode is [ ] flash off. For long time exposure photography, be sure to set the flash setting to [ ] flash off.
1. Rotate the mode dial to [
Tv
] Shutter Speed Priority mode.
2. Power on your camera.
3. Press the / button to select shutter speed.
The setting range is as follows:
8 6 5 4 3.2 2.5 2 1.6 1.3 1 0.8 0.6
0.5 0.4 0.3 1/4 1/5 1/6 1/8 1/10 1/13 1/15
1/20 1/25 1/30 1/40 1/50 1/60 1/80 1/100
1/125 1/160 1/200 1/250 1/320 1/400 1/500 1/640
1/800 1/1000 1/1250 1/1500
4. Compose your picture.
5. Press the shutter button.
35
E
When you set the aperture mode, the camera automatically selects a shutter speed to fit the brightness.
Choosing a lower aperture value (Higher F value) letting you fade the background and create a beautiful portrait. A higher aperture value (Lower F value) both close objects and distant objects (such as landscape scenery) will be in focus. The larger the aperture value, the greater the range of the image brought into clear focus. The flash default setting for [
Av
] Aperture Priority mode is [ ] flash off. For long time exposure photography, be sure to set the flash setting to [ ] flash off.
1. Rotate the mode dial to [
Av
] Aperture Priority mode.
2. Power on your camera.
3. Press the / button to select a value. The aperture range varies based on the optical zoom status.
The setting range is as follows:
Wide mode: F2.8 F5.6
Tele mode: F4.8 F9.7
4. Compose your picture.
5. Press the shutter button.
F
G
S
36
Resolution and quality settings determine the pixel size (dimension), image file size, and compression ratio for your images. These settings affect the number of images that can be stored in memory, or on an SD memory card. As you get to know the camera, it is recommended that you try each quality and resolution setting to get an appreciation for the effects that these settings will have on your images.
Higher resolution and higher quality images offer the best photographic results but produce large files sizes. Therefore, fewer images will take up more memory space.
High resolution and quality settings are recommended for printed output and situations requiring the finest detail. Lower resolution/quality images take up less memory space and may be quite suitable for sharing images via e-mail, in a report, or on a web page.
To change image resolution and quality settings:
1. Rotate the mode dial to one of [
A
] Auto mode, [
M
] Manual mode,
[
Av
] Aperture Priority mode, [
Tv
] Shutter Speed Priority mode,
[
SCENE
] Scene mode or [
P
] Program mode.
2. Power on your camera.
3. Press the [ ] menu button.
4. Select
IMAGE SIZE
or
IMAGE QUALITY
by using the / button, then press the button.
5. Change the settings with the / button and press again the button to confirm.
6. To exit from the menu mode, press again the [ ] menu button.
7. Compose your picture.
8. Press the shutter button.
37
E
F
Possible Number of Shots (Still Image)
The frame counter indicates the approximate number of images that can be stored on the internal memory or the SD memory card at the camera’s image quality and size settings.
Resolution Quality
2272 x 1704
1600 x 1200
1280 x 960
640 x 480
16MB
Internal
Memory
30
61
23
47
7
14
29
15
95
95
191
383
SD Memory Card
8MB 16MB 32MB 64MB 128MB 256MB 512MB
14
28
10
21
3
6
13
7
43
43
87
175
7
14
29
15
30
61
24
48
96
96
193
286
15
31
62
32
64
129
50
101
202
202
404
808
31
63
127
66
132
264
103
206
413
413
826
1653
64
128
257
133
267
534
208
417
835
835
1670
3341
122
245
491
254
509
1018
397
795
1591
1591
3182
6364
258
517
1035
536
1073
2146
838
1676
3353
3353
6707
13414
* The above data shows the standard testing results. The actual capacity varies according to the shooting conditions and settings
G
S
38
Your camera adjusts the exposure of each scene automatically. However, if the subject is very dark or very bright, you may override the camera automatic exposure determination to make the subject brighter or darker. This is called “EV compensation”.
1. Rotate the mode dial to one of [
M
] Manual mode, [
Av
] Aperture
Priority mode, [
Tv
] Shutter Speed Priority or [
P
] Program mode.
2. Power on your camera.
3. Press the [ ] menu button.
4. Select “EV” by using the / button, then press the button.
5. Change the settings with the / button and press again the button to confirm.
The EV compensation can be adjusted from [-2.0 EV] to [+2.0
EV].
The setting range is as follows:
+2.0 +1.5 +1.0 +0.5 +0.0 -0.5 -1.0 -1.5 -2.0
6. To exit from the menu mode, press again the [ ] menu button.
7. Compose your picture.
8. Press the shutter button.
Effective Subjects and Set Values
Positive (+) Compensation
* Copying of printed text (black characters on white paper)
* Backlit portraits
* Very bright scenes (such as snowfields) and highly reflective subjects
* Shots made up predominantly of sky
Negative (-) Compensation
* Spot lighted subjects, particularly against dark backgrounds
* Imaging of printed text (white characters on black paper)
* Scenes with low reflectivity, such as shots of green or dark foliage
39
E
F
G
The human eye adapts to changes in light so that white objects still appear white even when the light changes. With cameras, however, the color of the subject is influenced by the color of the light surrounding it. This color adjustment is called “white balance adjustment”. This setting allows you to set the white balance when taking images under specific lighting condition.
1. Rotate the mode dial to one of [
M
] Manual mode, [
Av
] Aperture
Priority mode, [
Tv
] Shutter Speed Priority or [
P
] Program mode.
2. Power on your camera.
3. Press the [ ] menu button.
4. Select “WHITE BALANCE” by using the / button, then press the button.
5. Change the setting with the / button and press again the button to confirm.
6. To exit from the menu mode, press again the [ ] menu button.
7. Compose your picture.
8. Press the shutter button.
[
[
[
[ AUTO ]:
[
[
DAYLIGHT ]:
CLOUDY ]:
SUNSET ]:
TUNGSTEN ]:
FLUORESCENT ]: automatically adjusting the white balance.
for recording outdoors on a bright day.
recording for overcast, shaded, twilight or evening skies.
for recording under sunset.
for recording under tungsten lighting condition.
for recording under fluorescent lighting condition.
S
40
Set the metering method to calculate the exposure.
1. Rotate the mode dial to one of [
M
] Manual mode, [
Av
] Aperture
Priority mode, [
Tv
] Shutter Speed Priority or [
P
] Program mode.
2. Power on your camera.
3. Press the [ ] menu button.
4. Select “METERING” by using the / button, then press the button.
5. Change the setting with the / button and press again the button to confirm.
MULTI
(The camera divides images into several zones for metering and evaluates the complex lighting conditions).
SPOT
(Meters the area within the spot automatic exposure point frame at the center of the LCD monitor).
6. To exit from the menu mode, press again the [ ] menu button.
7. Compose your picture.
8. Press the shutter button.
41
E
Play back photographed still images one image at a time.
1. Power on your camera.
2. Press the [ ] Playback button.
The last recorded image appears on the LCD monitor.
3. View and select your recorded images by using the / button.
To view the previous image, press the button.
To view the next image, press the button.
Pressing the button displays the image in the direction of clockwise.
Pressing the button displays the image in the direction of counterclockwise.
Pressing the button displays detailed information of the image.
F
G
S
42
If there is no image stored in the internal memory or on the memory card, [ NO IMAGE] is displayed on the screen.
You can also view your images on the TV screen. First connect one end of the A/V cable to the A/V OUT jack of the camera. Then connect the other end to the video input socket of the TV. Set the camera to the [ ] mode and then turn the TV and camera on.
During playback, the recorded image appears to be larger than the one on preview in capture mode.
A maximum of 30 seconds of audio can be recorded like a memo for photographed still images.
1. Power on the camera.
2. Press the [ ] Playback button.
The last recorded image appears on the LCD monitor.
3. Select the still image that you want to attach the voice memo by using the / button.
4. Press the [ ] menu button and select “VOICE MEMO” by using the / button and press the
button.
5. Select “RECORD” and press the button.
[PROCESSING...] is displayed on the screen and recording starts.
6. To stop recording voice memo during recording, press the button again.
A [ ] icon is displayed with images that have been recorded with a voice memo.
Playing back voice memo
The camera is not equipped with speakers. To play back the voice memo, you may connect the camera to the television with the A/V cable or download your files to your computer hard disk.
Recording voice memos automatically reduces the space available on your memory card for pictures.
43
E
F
While reviewing your images, you may enlarge a selected portion of an image. This magnification allows you to view fine details.
1. Power on your camera.
2. Press the [ ] playback button.
The last recorded image appears on the LCD monitor.
3. Use the / button to select the image you want to enlarge.
4. Adjust the zoom ratio by sliding the zoom controller left or right.
Sliding the zoom controller towards [
T
] will enlarge the image.
To return to normal magnification, slide the zoom controller towards [
W
].
The image is displayed enlarged, you will see a white frame with a green box inside. The white frame indicates the entire image, while the green box shows the location of the currently enlarged area.
5. Use the / / / button to select the area to enlarge.
6. To return to the regular display from 6X-enlarged status, press the
button.
Keep sliding the zoom controller towards [
W
] will change into thumbnail images.
G
Pressing the [
T
] button magnifies the image from 1.3X 2.0X 2.2X 2.4X 2.6X 2.8X 3.0X 3.2X
3.4X 3.6X 3.8X 4.0X 6.0X.
S
44
This feature allows you to view four or nine thumbnail images on the LCD monitor simultaneously so that you can quickly scan for a particular image.
1. Power on your camera.
2. Press the [ ] playback button.
The last recorded image appears on the LCD monitor.
3. Slide the zoom controller towards [
W
] once.
Four thumbnail images are displayed on the LCD monitor. Sliding again the zoom controller towards [
W
] while displaying four thumbnail images displays nine thumbnail images.
If the image is recorded with voice memo, Voice icon will be displayed.
For recorded video clips, the [ ] video mode icon will be displayed.
4. Use the / / / button to move the cursor to select the image to be displayed at regular size.
5. Press the button to display the selected image on the full screen.
While displaying thumbnail images, pressing the [ ] delete button the current selected image will be erased.
45
E
F
Play back video clips recorded on the camera.
To view the recorded video clips, follow the steps below.
1. Power on your camera.
2. Press the [ ] playback button.
3. Select the video clip that you want to view by using the / button.
4. Press the button to start.
While playing the video clips, the screen also indicates the elapsed time.
Press the button the recorded video clip will display as x1 x2 x3 x1/2 (fast reverse)
Press the button the recorded video clip will display as x1 x2 x3 x1/2 (fast forward)
To pause playback, press the button.
To stop playback, press the button.
G
S
46
Zoom function cannot be activated while playing back the video clips.
When playing the video clips on TV, recorded voice can be played back.
The function enables you to play your images back automatically in sequential order as a slide show.
This is a very useful and entertaining feature reviewing recorded images and for presentations.
1. Power on your camera.
2. Press the [ ] playback button.
3. Press the [ ] menu button and select “SLIDE SHOW” by using the / button and press the button.
4. Set the playback interval by using the / button.
To not set automated playback (slide show) you may choose
RETURN
and press the button.
5. To confirm the setting press again the button.
The slide show starts.
The video clips are displayed the first frame image, and not played back.
To stop slide show, press the button.
You can adjust the slide show display interval within the range of 3 sec., 6sec. and 10 sec.
47
E
This option lets you prevent recorded images or video clips from being accidentally erased.
1. Power on your camera.
2. Press the [ ] playback button.
3. Press the [ ] menu button and select “PROTECT” by using the / button and press the button.
4. You can select whether to protect one image/video or all images/ video clips by using the / button and press the button.
[PROTECT ONE]: Protect one image/video clip at one time.
[PROTECT ALL]: Protect all images/video clips at once.
5. Select “UNLOCK” or “LOCK” by using the / button and press the button to confirm the setting.
[UNLOCK]:Unlock the protected image or video clip.
[LOCK]: Protect the selected image/video clip or all images/ video clips
F
[ ] protect icon will display on the LCD monitor to indicate as a protected image or video clip.
G
S
48
You can erased a captured image or a recorded video clip at a time by pressing the [ ] delete button.
1. Power on your camera.
2. Press the [ ] playback button.
The last image frame appears on the LCD monitor.
3. View and select unwanted photographed image by using the /
button, then press the [ ] delete button.
4. Continue the deletion if necessary
If all images are erased, [ NO IMAGE] will pop up.
To exit the deletion, press again the [ ] playback button or rotate the mode dial.
Please be aware that deleted images cannot be recovered. Exercise adequate caution before deleting a picture.
Protected images cannot be deleted with the erase function.
49
E
1. Power on your camera.
2. Press the [ ] playback button.
3. Press the [ ] menu button and select “DELETE” by using the / button and press the button to enter the sub-menu.
4. Select [ALL IMAGES ON MEMORY] by using the / button, then the button.
If SD card is inserted, then [ALL IMAGES ON CARD] is displayed.
5. “DELETE ALL IMAGES ON MEMORY?” message appears on the image.
If SD card is inserted, then “DELETE ALL IMAGES ON CARD?
” is displayed.
6. Use the / button to select YES, and press the button.
If you want to cancel the deletion, select NO.
If all images are erased, [ NO IMAGE] will pop up.
F
G
S
50
Please be aware that deleted images cannot be recovered. Exercise adequate caution before deleting a picture.
Protected images cannot be deleted with the erase function.
Selecting the "SELECT" option allows you to delete one or more chosen images/video clips at a time. The images/ video clips will be displayed in thumbnail format. Select the images you want to delete by using the / / / button and press the button to confirm. Press the button to execute your request.
Using this option to remove all the recorded images/video clips or other data on camera internal memory or on an SD card.
1. Power on your camera.
2. Press the [ ] playback button.
3. Press the [ ] menu button and select “DELETE” by using the / button and press the button to enter the sub-menu.
4. Select [FORMAT MEMORY] by using the / button, then the
button.
If SD card is inserted, then [FORMAT CARD] is displayed.
5. “FORMAT MEMORY?” message appears on the image.
If SD card is inserted, then “FORMAT CARD?” is displayed.
6. Use the / button to select
YES
, and press the button.
If you want to cancel the deletion, select
NO
.
If all data is formatted, [ NO IMAGE] will pop up.
The SD memory card cannot be formatted when it is write-protected.
Formatting the SD memory card also erases the protected images. All data other than images are also erased.
Before formatting the card, make sure that none of the images on the card are still required.
51
E
F
DPOF (Digital Print Order Format) allows you to embed printing information on your SD memory card.
By using DPOF, you can select an image to be printed and then specify how many prints or which image you would like. Take your SD memory card to a DPOF enabled printer or through laboratory printing services that accept memory cards. The DPOF/card-compatible printer will read the embedded information on the memory card and print your images as specified.
To set DPOF:
1. Power on your camera.
2. Press the [ ] playback button.
3. Press the [ ] menu button and select
DPOF
by using the / button and press the button to enter the sub-menu.
4. Select the desired setting by using the / button.
[ ] DPOF icon is displayed on the DPOF-setting image.
The DPOF sub-menu options:
[QUANTITY]: Select the print quantity from 0~9.
[SET IMAGE]: Allows you to select your preferred image.
[RETURN]: Exit the menu.
G
S
52
To print out images recorded in the internal memory, it is necessary to copy your images to an SD memory card first. Refer to chapter "COPY TO CARD" in Playback Menu for further details.
You can share recorded images/ video clips with your family or friends via e-mail or post them on the
Web. Before doing those things, you need to connect the camera to your computer by using the USB cable and then transfer the images/video clips.
To transfer images/video clips from the camera to your computer, follow the steps below:
Step 1:
Installing the USB driver
Step 2:
Connecting the camera to your computer
Step 3:
Downloading images/video clips
CPU
OS
Memory
System Requirements
(Windows)
Pentium 166 MHz processor or higher
Windows 98/98SE/Me/2000/XP
32MB
(64MB RAM recommended)
Free Space on Hard Disk 128MB hard disk space
Required Devices A CD-ROM Drive,
An Available USB Port
System Requirements
(Macintosh)
PowerPC G3/G4
OS 8.6 or higher
32MB
(64MB RAM recommended)
128MB hard disk space
A CD-ROM Drive,
An Available USB Port
Color Monitor Color Monitor (800x600, 24-bit or higher recommended)
Color Monitor (800x600, 24-bit or higher recommended)
53
Step 1: Installing the USB Driver on a Windows PC
The USB driver on the supplied CD-ROM is exclusively for Windows 98. Installing the USB driver on computers running
Windows 2000/Me/XP
is not necessary.
1. Insert the CD-ROM packaged with the camera into the CD-ROM drive.
The welcome screen appears.
2. Click “Install USB Driver”. Follow the on-screen instructions to complete the installation. After the USB driver installation is complete, restart your computer.
E
F
G
Installing the USB Driver on a Macintosh PC
Mac OS 8.6 users must install a USB driver. For Mac OS 9.0 or higher version, the computer will automatically recognize the camera and load its own USB drivers.
1. Insert the CD-ROM that packaged with the camera into your CD-ROM drive.
2. Select and double-click “Digital Camera Driver Installer”.
3. Select “Install Location” and click “Install”.
4. Follow the on-screen instructions to complete the installation and restart your computer.
S
54
Step 2: Connecting the Camera to Your Computer
1. Connect one end of the USB cable to an available USB port on your computer.
2. Connect the other end of the USB cable to the USB connector on the camera.
3. Turn the camera on.
4. Look for a new “Removable Disk” icon appearing in the “My
Computer” window. Your recorded images/video clips will be in a folder on this “removable disk”.
(For Mac users, double-click the “untitled” disk on the desktop.)
55
Step 3: Downloading Images/Video Clips
When the camera is turned on and connected to your computer, it is considered to be a disk drive, just like a floppy disk or CD. You can download (transfer) images by copying them from the “removable disk” (“untitled” disk on a Macintosh) to your computer hard drive.
For Computers Running Windows
Open the “removable disk” by double clicking on it. Double click on the folder contains your recorded images/video clips. Select the images/video clips that you prefer and then choose “Copy” from the
“Edit” menu. After that, open the destination location and choose “Paste” from the “Edit” menu.
E
F
For Computers Running Mac OS
Open the “untitled” disk window and the hard disk or the destination location. Drag and drop from the camera disk to the desired destination.
G
S
56
It is recommended that you use the AC power adapter as a power supply for the camera while transferring your images/video clips from the camera to your computer to avoid the camera maybe cut off unexpectedly when the batteries run out.
Memory card users may prefer to use a memory card reader (highly recommended).
PhotoSuite is a very user-friendly image-editing program. With PhotoSuite, you can breezily retouch, compose and organize your images. It contains a variety of templates, such as photo frames, birthday cards, calendars and more. Get your images ready and go explore this amazing program.
To Install PhotoSuite
1. Insert the CD-ROM packaged with the camera into the CD-ROM drive.
The welcome screen appears.
2. Click “Install PhotoSuite”. Follow the on-screen instructions to complete the installation.
For information on how to use PhotoSuite to edit and retouch your recorded images, please refer to its online help.
For Windows 2000/XP users, make sure to install and use the PhotoSuite while logged in as a user with an
“Administrator” account.
PhotoSuite is not supported on the Mac.
57
PhotoVista is an easy-to-use program that lets you create spectacular 360
0
panoramic images in a snap. When you view these panoramas, you can get the experience of being totally immersed in a realistic environment. PhotoVista’s powerful engine quickly and automatically stitches images together, and its intuitive interface will let even a novice get great results in minutes.
To Install PhotoVista
1. Insert the CD-ROM packaged with the camera into the CD-ROM drive.
The welcome screen appears.
2. Click “Install PhotoVista”. Follow the on-screen instructions to complete the installation.
E
F
G
S
58
For information on how to use PhotoVista to create spectacular 360
0
panoramic images, please refer to its online help.
For Windows 2000/XP users, make sure to install and use the PhotoVista while logged in as a user with an
Administrator account.
For Windows XP users which OS version does not include Service Pack 1 or higher, be sure to link to http://www.java.com/en/download/windows_automatic.jsp first and download the Java Virtual Machine installation.
For more detail information about Java, please refer to its on-line help at http://java.sun.com/getjava/help.html
After java software installation, you can start to install iSee Media Photovista Panorama.
Hereunder is iSee Media Photovista Panorama system requirements and recommendations:
Windows 95/ Windows 98/ Windows NT 4 (Service Pack 3 or higher);
Windows 2000/ Windows Me/ Windows XP (Service Pack 1 or higher).
PhotoVista is not supported on the Mac.
This feature allows you to determine the conditions you would like to choose before taking images.
Navigate the options you wish to configure by using the / button.
You may press the / button and then the button to enter the sub-menu. To confirm the setting press the button again.
Capture menu items: IMAGE SIZE, IMAGE QUALITY, COLOR,
SATURATION, SHARPNESS, FOCUS, QUICK
VIEW, HISTOGRAM, CAPTURE MODE, EV,
WHITE BALANCE, ISO and METERING.
IMAGE SIZE
Refer to chapter “Changing Image Resolution and Quality” in
Photography-Selecting Particular Effects for further details.
IMAGE QUALITY
Refer to chapter “Changing Image Resolution and Quality” in
Photography-Selecting Particular Effects for further details.
59
COLOR
To capture an image, your camera offers you four types of color (Full color/Vivid/Black and White/
Sepia) to match with your preference.
Your images will demonstrate different impression by choosing different types of color.
[ FULL COLOR ]: Records the image in full colors.
[ VIVID ]: Records the image in brighter colors.
[ BLACK & WHITE ]: Records the image in black and white.
[ SEPIA ]: Records the image in sepia tones.
E
F
G
SATURATION
To capture an image, your camera offers you three different degrees of color (Low/Medium/High) to match with your preference.
Your images will demonstrate different impression by selecting different degrees of color. This is called “Saturation”.
[ LOW ]: Decreases the image contrast.
[ MEDIUM ]: Averages the image contrast
[ HIGH ]: Increases the image contrast
S
60
SHARPNESS
Your camera will automatically emphasize the borders (Low/Medium/High) between light and dark areas of the image.
This will make the image’s edges look sharper.
[
L
LOW ]
[ MEDIUM ]
[
H
HIGH ]
FOCUS
You can take images with the distance to the subject set by auto focus, macro, fixed at 1 meter, fixed at 3 meters or infinity.
[ AUTO ]: Leave the settings up to the camera to take images with ease.
[ MACRO ]: Take images of subjects within 0.1m (wide) and 0.3m (tele) of the camera. Marco
[ 1M ]: photography is not possible to use in the Scene mode.
Take images of subjects about 1m from the camera.
[ 3M ]: Take images of subjects about 3m from the camera.
[ INFINITY ]: Take images of subjects about 8m or more from the camera.
QUICK VIEW
Set to display a captured image on LCD monitor immediately after you have taken the shot.
[OFF]: Do not display quick view.
[ON]: Display quick view.
61
E
HISTOGRAM
Set to display a graph indicating the distribution of brightness in the image.
[ OFF ]:Do not display the histogram.
[ ON ]: Display the histogram.
CAPTURE MODE
Set the capturing method that is used for taking images.
[ SINGLE ]: 1 image recorded at each shot.
[ MULTI ]: 16 frames are taken successively. Effective for taking moving subjects continuously.
[ BURST ]: 3 images are taken successively. Effective for taking moving subjects continuously.
[ AEB ]: Automatic Exposure Bracketing 3 images are taken consecutively in the order of standard exposure, underexposure and overexposure compensation.
F
G
Selecting the "MULTI", "BURST" and "AEB" as the capturing method will disable the digital zoom and flash photography.
EV
Refer to chapter “Adjusting the Exposure Compensation” in Photography-Selecting Particular Effects for further details.
S
62
This setting is not available for [
A
] Auto mode and [
SCENE
] Scene mode.
WHITE BALANCE
Refer to chapter “Setting the White Balance” in Photography-Selecting Particular Effects for further details.
This setting is not available for [
A
] Auto mode and [
SCENE
] Scene mode.
ISO
The ISO speed decides the sensitivity to the lights. The higher the ISO number is, the more sensitive it is to the lights. When recording under dark situations or recording a fast moving, use a high-number setting. However, while recording high quality images, we suggest you to use a low-number setting.
[ AUTO ]: adjusts the ISO speed automatically.
[
[
[
ISO
100
ISO
200
ISO
400
100 ]: equivalent to ISO 100.
200 ]: high-sensitive photography, equivalent to ISO 200.
400 ]: high-sensitive photography, equivalent to ISO 400.
This setting is not available for [
A
] Auto mode and [
SCENE
] Scene mode.
METERING
Refer to chapter “Switching between Metering Modes” in Photography-Selecting Particular Effects for further details.
63
E
This feature allows you to transfer your recorded images/video clips to a SD memory card, to create an on-camera slide show or configure
DPOF settings. You may also delete one or all stored images, format your SD memory card or the internal memory.
Navigate the options you wish to configure by using the / button.
You may press the / button and then the button to enter the sub-menu. To confirm the setting press the button again.
Playback menu items:DELETE, COPY TO CARD, SLIDE SHOW,
DPOF, PROTECT, QUALITY CHANGE,
RESIZE, VOICE MEMO and SET AS LOGO.
F
G
S
64
DELETE
Refer to chapter “ERASING” for further details.
[ THIS IMAGE ]: Delete the current image or video clip.
[ ALL IMAGES ON CARD/MEMORY ]: Delete all images or video clips recorded on the SD memory
[ SELECT ]:
[ FORMAT CARD/MEMORY ]: card or internal memory.
Delete the selected image or video clip.
Format all data recorded on the SD memory card or internal memory.
[ RETURN ] Exit from the delete menu.
COPY TO CARD
This feature allows you to copy your images from the camera’s internal memory to a memory card. Of course, you can only do this if you have a memory card installed and some images in internal memory.
[ NO ]: Does not copy the images to the memory card.
[ YES ]:Copy all images to the memory card.
SLIDE SHOW
Your camera can display your images sequentially as a slide show. Refer to chapter “Automated
Playback (Slide Show)” for further details.
[ 3 SEC. ]: Set 3 seconds as slide show interval.
[ 6 SEC. ]: Set 6 seconds as slide show interval.
[ 10 SEC. ]: Set 10 seconds as slide show interval.
[ RETURN ]: Does not play slide show.
65
E
F
DPOF
Refer to chapter “Print Settings (DPOF Settings)” for further details.
PROTECT
Refer to chapter “Protecting Images/Video Clips” in Replaying for further details.
QUALITY CHANGE
Compresses images down to half of their size or more, overwrites an old size image with a newly compressed image.
Compressing a previously saved image when the memory capacity has run out of storage space during photography increases space on the memory so that you can continue taking photographs.
The following images cannot be resized:
(Economy) quality images
Images taken with other camera
Protected images
Video clips
Image quality cannot be changed when the SD card is write-protected.
G
S
66
RESIZE
Resizing a previously saved image when the memory capacity has run out of the storage space during photography increases space on the memory so that you can continue taking photographs.
The following images cannot be resized:
Image size (640x480)
Image taken with other camera
Protected images
Video clips
Images cannot be resized when the SD card is write-protected
VOICE MEMO
You can record a voice memo on the captured images. Recorded time can last for 30 seconds. Refer to chapter "Recording Voice Memos" for further details.
[ RECORD ]: Record voice memo on the image.
[ RETURN ]: Does not record voice memo on the image.
SET AS LOGO
You may set camera’s startup image according to your preference.
[ SET ]: Select camera’s startup image.
[ SET TO DEFAULT ]: Do not select camera’s startup image.
[ RETURN ]: Exit from the menu.
67
E
This feature allows you to adjust video quality and video color while recording movies.
Navigate the options you wish to configure by using the / button. You may press the / button and then the button to enter the sub-menu. To confirm the setting press the button again.
Video menu items: VIDEO QUALITY and VIDEO COLOR.
VIDEO QUALITY
Change the quality (compression ratio) of image to normal or fine.
[ NORMAL ]
[ FINE ]
F
G
VIDEO COLOR
Change the color of image to full color, vivid, black and white and sepia.
[ FULL COLOR ]: Records the image in full colors.
[ VIVID ]: Records the image in brighter colors.
[ BLACK & WHITE]: Records the image in black and white.
[ SEPIA]: Records the image in sepia tones.
S
68
This feature allows you to set up the default settings for using you camera in addition to image-related settings. You can select your personal preferences for the camera by this mode.
Navigate the options you wish to configure by using the / button.
You may press the / button and then the button to enter the sub-menu. To confirm the setting press the button again.
Setup menu items: DATE & TIME, TV, BEEPER, LANGUAGE,
POWER OFF, SET TO DEFAULT,
LCD BRIGHTNESS, RESET NUMBER and DATE
IMPRINT.
DATE & TIME
Refer to chapter “Setting the Date and Time” in Preparing Your
Camera for further details.
69
E
F
G
S
TV
Set the video output system according to the country in which your camera is used.
[ NTSC ]: NTSC system.
[ PAL ]: PAL system.
BEEPER
The camera makes a sound (beep) each time you press the camera button if this function is enabled.
[LOUDER]: The camera generates a stronger sound.
[SOFT]: The camera generates a weaker sound.
[OFF]: The camera does not generate a sound.
LANGUAGE
Refer to chapter “Setting the Language” in Preparing Your Camera for further details.
POWER OFF
If no operation is performed for a specific period of time, the power to the camera is automatically turned off. This feature is useful to conserve power.
[ 3 MIN ]: If no operation is carried out for 3 minutes, auto power off is activated.
[ 5 MIN ]: If no operation is carried out for 5 minutes, auto power off is activated.
[ 10 MIN ]: If no operation is carried out for 10 minutes, auto power off is activated.
[ OFF ]: Disable Auto power off.
70
SET TO DEFAULT
Set all the parameters to default settings.
[ YES ]:Reset to default settings.
[ NO ]: Remain the current settings.
LCD BRIGHTNESS
Adjust the brightness of the LCD monitor.
button: Darkens the display.
button: Lightens the display.
RESET NUMBER
Set whether or not to reset the file number when you take photographs. This creates a new folder.
The photographed images are recorded to the newly created folder from number 0001. If you want to reset the file number, be sure that no images are recorded in the internal memory or the SD memory card.
[ YES ]:Reset the file number.
[ NO ]: Does not reset the file number.
DATE IMPRINT
The date of recording can be printed directly on the still images. This function must be activated before the image is taken.
[ YES ]:Date and time will be displayed on the captured image.
[ NO ]: Date and time will not be displayed on the captured image.
71
E
F
G
S
72
TV
AV Cable
SD Memory Card
USB Cable
PCMCIA Adapter
Notebook
Computer
Printer
Item
Image sensor
Effective pixels
Image size
Image quality
Recording media
Lens
LCD monitor
Self-timer
Zoom
Description
CCD
4.0 Million
Still image:
2272 x 1704; 1600 x 1200; 1280 x 960; 640 x 480
Video clip:
256 x 192
Fine, Normal, Economy
16MB internal memory;
SD memory card (optional) (up to 512MB capacity)
Focal length: 5.4mm~Tele: 16.2mm
Focusing range: Macro: 0.06m~infinity(Wide)
0.35m~infinity(Tele)
Normal: 0.5m~infinity
F-number: Wide: F2.8-F5.6
Tele: F4.8-F9.7
1.5" LTPS TFT color LCD;
High-resolution display (130K pixels)
5-second delay, 10-second delay, 10+2-second delay
Optical:3X;
Digital: Capture mode: 4X/ Playback mode: 6X
73
E
F
Item
Exposure compensation
White Balance
Compressed format
Standards
Interface
Power
Description
Auto;
Manual: -2.0 ~ +2.0 EV
Auto;
Manual: Daylight, Cloudy, Sunset, Tungsten, Fluorescent
JPEG, MPEG 1 Level 1 for video clip
JPEG, EXIF 2.2, DPOF 1.0, DCF 1.1, MPEG 1 Level 1
DC IN jack, USB connector, A/V jack (NTSC or PAL)
2 X AA Alkaline batteries (optional),
2 x AA Ni-MH batteries (optional), one CR-V3 Lithium battery pack (3V) (optional),
Dimensions
Weight
AC power adapter (2.5A/3.0V) (optional)
107mm x 56mm x 33.5mm (WxHxD)
Approx. 142g
(without batteries and the SD memory card)
* Design and specifications are subject to change without notice.
G
S
74
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project