Maytag MEW6627DDQ Datasheet

www.dexpress.com

DIMENSION EXPR

ESS

Fax on Demand (775) 833-3600

This Data Sheet Includes Information On

Maytag

• Product Model Number (s): •

27" Electric Double Ovens:

MEW6627DDB, MEW6627DDS, MEW6627DDQ and

MEW6627DDW

27"

25 1/2"

24"

• Dimensions (Actual Size) •

Cutout width: 25 1/2"

Cutout height: 50"

Cutout depth: 24"

Minimum cabinet width: 27"

Recommended cutout location from floor : 4" - 12"

Distance from face of cabinet to outer edge of open doors (Door swing): 20 1/2"

Distance from face of cabinet to front of closed door handle: 15/16"

Overall unit width: 26 3/4"

Overall unit height: 50 1/4"

Penetration into cabinet: 23 1/2"

Oven overlap distances when using cutout dimensions listed above:

Top overlap: 1/4"

Bottom overlap: 0"

Right side overlap: 5/8"

Left side overlap: 5/8"

• Additional Information •

• Cutout in cabinet should be level and straight. There are no provisions to level the unit after it is installed.

• Do not block air intake slots along bottom of oven.

• Construct 5/8" minimum plywood floor flush with bottom of opening. Floor must be level and straight and capable of supporting 250 lbs.

• A three-wire, single phase, A.C. 120/208-240 volt,

60Hz cycle electrical system protected by a 40 amp fuse or comparable circuit breaker must be provided .

7/8" O.D. flexible cable 4 feet long is furnished by manufacturer. Mount junction box in area under plywood floor if adequate lower cabinet space is available. Locate 1 1/4" conduit access hole in the back right hand side of the plywood floor.

• For European style cabinets (flush front) the required clearance for operation of the oven door is a minimum spacing of 1" between the cutout and the door, hinge or drawer of the cabinet.

See page 2 for additional information

Cabinet Opening

(not to scale)

Provide for

120/208-240 volt electrical connection in this area.

23 1/2"

50"

4" - 12"

Overall Dimensions

50 1/4"

(not to scale)

26 3/4"

15/16"

Subject to change without notice. This system is designed to be updated daily if necessary. Dimension Express is not responsible for use of superseded, voided, or outdated data sheets. Because of the difficulty or impracticability of determining actual damages, liability of Dimension Express shall not exceed $50.00.

Copyright © Dimension Express, 2003.

213

• NEVER reuse Data Sheets. Data Sheets are subject to change without • Call Dimension Express if you have any questions at (775) 833-3633 • notice. Dimension Express is a FREE service bureau and is updated daily, • Always refer to a current Code at a Glance or manufacturer directory • it makes far more sense to spend the time necessary to request new Data • Data Sheet codes change on the first of odd numbered months at 12:01am •

Sheets for each project, as opposed to the problems, time, costs, and risks associated with reusing old Data Sheets.

BN207.5 • A213B276 • • 031211 • 82155 • 90845

www.dexpress.com

DIMENSION EXPR

ESS

Fax on Demand (775) 833-3600

Additional Information:

Page 2

This Data Sheet Includes Information On

Maytag

• Product Model Number (s): •

27" Electric Double Ovens:

MEW6627DDB, MEW6627DDS, MEW6627DDQ and

MEW6627DDW

1 1/2" minimum wide rail

Cabinet door

There must be 1" minimum between bottom of cabinet door and top of oven console.

Oven Control Console

Side View

(not to scale)

Oven opening floor

1" minimum from oven opening floor to top of cabinet door or drawer front.

Cabinet door or drawer front

Subject to change without notice. This system is designed to be updated daily if necessary. Dimension Express is not responsible for use of superseded, voided, or outdated data sheets. Because of the difficulty or impracticability of determining actual damages, liability of Dimension Express shall not exceed $50.00.

Copyright © Dimension Express, 2003.

276

• NEVER reuse Data Sheets. Data Sheets are subject to change without • Call Dimension Express if you have any questions at (775) 833-3633 • notice. Dimension Express is a FREE service bureau and is updated daily, • Always refer to a current Code at a Glance or manufacturer directory • it makes far more sense to spend the time necessary to request new Data • Data Sheet codes change on the first of odd numbered months at 12:01am •

Sheets for each project, as opposed to the problems, time, costs, and risks associated with reusing old Data Sheets.

BN207.5 • A213B276 • • 031211 • 82155 • 90845