advertisement
ET1
ENTERPRISE TABLET
USER GUIDE
Copyrights
The Motorola products described in this document may include copyrighted Motorola computer programs. Laws in the United States and other countries preserve for Motorola certain exclusive rights for copyrighted computer programs. Accordingly, any copyrighted Motorola computer programs contained in the Motorola products described in this document may not be copied or reproduced in any manner without the express written permission of Motorola.
© 2013 Motorola Solutions, Inc. All Rights Reserved
No part of this document may be reproduced, transmitted, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, without the prior written permission of Motorola
Solutions, Inc.
Furthermore, the purchase of Motorola products shall not be deemed to grant either directly or by implication, estoppel or otherwise, any license under the copyrights, patents or patent applications of Motorola, except for the normal non-exclusive, royalty-free license to use that arises by operation of law in the sale of a product.
Disclaimer
Please note that certain features, facilities, and capabilities described in this document may not be applicable to or licensed for use on a particular system, or may be dependent upon the characteristics of a particular mobile subscriber unit or configuration of certain parameters. Please refer to your Motorola contact for further information.
Trademarks
MOTOROLA, MOTO, MOTOROLA SOLUTIONS, and the Stylized M Logo are trademarks or registered trademarks of Motorola Trademark Holdings, LLC and are used under license. All other trademarks are the property of their respective owners.
European Union (EU) Waste of Electrical and Electronic Equipment
(WEEE) directive
The European Union's WEEE directive requires that products sold into EU countries must have the crossed out trash bin label on the product (or the package in some cases).
As defined by the WEEE directive, this cross-out trash bin label means that customers and end-users in EU countries should not dispose of electronic and electrical equipment or accessories in household waste.
Customers or end-users in EU countries should contact their local equipment supplier representative or service centre for information about the waste collection system in their country.
i
Revision History
Changes to the original guide are listed below:
Change
-01 Rev A
Date
07/11/2013 Initial release.
Description
iii
Contents
v
ET1 Enterprise Tablet User Guide
vi
Revision History
vii
List of Tables
ix
List of Figures
xi
ET1 Enterprise Tablet User Guide
xii
About This Guide
This guide provides information on using the ET1 Enterprise Tablet and accessories.
Screens and windows pictured in this guide are samples and can differ from actual screens.
Documentation Set
The documentation set for the ET1 provides information for specific user needs, and includes:
• ET1 Enterprise Tablet Quick Start Guide - describes how to set up the ET1 and basic operating instructions.
• ET1 Enterprise Tablet User Guide - describes how to use the ET1.
• ET1 Enterprise Tablet Integrator Guide - describes how to configure the ET1 and accessories.
Configurations
This guide covers the following configurations:
Configuration Radios
ET1N0
ET1N2
WLAN:
802.11a/b/g/n
WPAN:
Bluetooth v2.1
with EDR
WLAN:
802.11a/b/g/n
WPAN:
Bluetooth v2.1
with EDR
WWAN:
HSDPA /
CDMA
Display
7.0” WSVGA
Color
7.0” WSVGA
Color
Memory
1 GB RAM / 4
GB Flash / 4 GB microSD card
1 GB RAM / 4
GB Flash / 4 GB microSD card
Data Capture
Options camera,
Scanning
Module,
Scanning/MSR
Module, optional CS3070 camera,
Scanning
Module,
Scanning/MSR
Module, optional CS3070
Operating
System
Android-based,
Android
Open-Source
Project 4.1.1
Android-based,
Android
Open-Source
Project 4.1.1
Software Versions
To determine the current software versions touch > About device .
• Serial number - Displays the serial number.
• Model number - Displays the model number.
• Android version - Displays the operating system version.
xiii
ET1 Enterprise Tablet User Guide
• Kernel version - Displays the kernel version number.
• Build number - Displays the software build number.
Chapter Descriptions
Topics covered in this guide are as follows:
•
provides information on getting the ET1 up and running for the first time.
•
provides basic instructions for using the ET1, including powering on and resetting the ET1.
•
provides information for capturing bar code data using the internal camera and optional scan modules and Bluetooth scanner.
•
provides information for configuring Wi-Fi.
•
provides information for configuring Bluetooth.
•
explains how to take photos, capture videos and video images in the Gallery application.
•
describes the available accessories and how to use them with the ET1.
•
8 Maintenance and Troubleshooting, page 8-1
includes instructions on cleaning and storing the ET1, and provides troubleshooting solutions for potential problems during ET1 operation.
•
A Technical Specifications, page A-1
provides the technical specifications for the ET1.
Notational Conventions
The following conventions are used in this document:
• Italics are used to highlight the following:
– Chapters and sections in this and related documents
– Icons on a screen.
• Bold text is used to highlight the following:
– Dialog box, window, and screen names
– Drop-down list and list box names
– Check box and radio button names
– Button names on a screen.
• Bullets (•) indicate:
– Action items
– Lists of alternatives
– Lists of required steps that are not necessarily sequential
• Sequential lists (for example, lists that describe step-by-step procedures) appear as numbered lists.
xiv
Icon Conventions
Icon Conventions
The documentation set is designed to give the reader more visual clues. The following graphic icons are used throughout the documentation set. These icons and their associated meanings are described below.
The word WARNING with the associated safety icon implies information that, if disregarded, could result in death or serious injury, or serious product damage.
The word CAUTION with the associated safety icon implies information that, if disregarded, may result in minor or moderate injury, or serious product damage.
NOTE contains information more important than the surrounding text, such as exceptions or preconditions.
They also refer the reader elsewhere for additional information, remind the reader how to complete an action (when it is not part of the current procedure, for instance), or tell the reader where something is located on the screen. There is no warning level associated with a note.
Related Documents
• ET1 Enterprise Tablet Quick Start Guide , p/n MN000021A01-xx
• ET1 Enterprise Tablet Regulatory Guide , p/n 72-148509-xx
• ET1 Enterprise Tablet Integrator Guide , p/n MN000022A01-xx
• Symbol CS3000 Series Scanner Product Reference Guide , p/n 72E-136088-xx
• MSP Client Software Guide , p/n 72E-128805-xx
• MSP 4.2 Release Notes , p/n 72E-100160-xx.
For the latest version of this guide and all guides, go to: http://supportcentral.motorolasolutions.com
Service Information
If you have a problem with your equipment, contact Motorola Solutions Global Customer Support Center for your region. Contact information is available at: http://www.motorolasolutions.com/support .
When contacting Motorola Solutions Global Customer Support Center, have the following information available:
• Serial number of the unit (found on the manufacturing label)
• Model number or product name (found on the manufacturing label)
• Software type and version number
xv
ET1 Enterprise Tablet User Guide
Motorola responds to calls by email or telephone within the time limits set in support agreements.
If the Motorola Solutions Global Customer Support Center cannot solve the problem, you may need to return the equipment for servicing. The Support Center provides the specific directions. Motorola is not responsible for any damages incurred during shipment if the approved shipping container is not used. Shipping the units improperly can possibly void the warranty.
If you purchased your product from a Motorola business partner, contact that business partner for support.
xvi
1
Getting Started
This chapter provides the features of the ET1 and explains how to set it up for the first time.
1.1 Features
Figure 1-1 Front View
1
2
3 4 5
6
1 3
12 11 10 9 8 7
MN000022A01 - May 2013 1-1
ET1 Enterprise Tablet User Guide
24
23
Figure 1-2 Back View
14 15
26
25
19
16 17
18
19
1-2
22 21 20
2
3
4
6
7
Table 1-1 Features
Number
1
5
8
Item
Decode LED
Microphone
Light Sensor
Battery Charge
LED
Communication
LED
Front-facing
Camera
Function
Indicates decode functionality. Lights red when scanning in process.
Lights green indicating a successful decode.
Use for making voice recordings.
Determines ambient light for controlling display backlight intensity.
Indicates battery charge state.
User programmable.
Use for capturing a front view picture. Use for making video calls with third-party video applications.
Menu Button — Opens a menu with items that affect the current screen or application.
Home Button — Displays the Home screen with a single touch. Displays recently used applications when held for a short period.
MN000022A01 - May 2013
1.1 Features
Table 1-1 Features (cont'd.)
Number
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
Item Function
Back Button — Displays the previous screen. Closes the keyboard if the on-screen keyboard is open.
P3
P2
P1
Touch Screen
Launches the Search application (default). User configurable.
Increases the volume (default). User configurable.
Decreases the volume (default). User configurable.
Displays all information required to operate the ET1.
Provides illumination for rear-facing camera.
Takes photos, videos, and captures bar code data.
Camera Flash
Rear-facing
Camera
USB Host
Expansion
Module
Provides USB host connection to a peripheral.
Scanning Module Provides 1D and 2D bar code scanning.
Scanning/MSR
Module
Provides 1D and 2D bar code scanning and magnetic stripe card reading.
Power Button Press and hold to turn on the ET1. Press to turn on or off the screen.
Press and hold to select one of these options:
• Silent mode - The device is set to vibrate mode; all sounds are disabled except for alarms.
• Airplane mode - Disable all wireless connections.
• Battery swap - Shut down the device when replacing the battery.
• Reset - Reboot the ET1 when software stops responding.
• Power off - Turn off the ET1.
Opens the scan application (default). Programmable.
Left Scan/Action
Button
Speakers
HDMI Output
Connector
I/O Connector
Headset Jack
Battery
Battery Latch
Side LED
Right
Scan/Action
Button
Provides audio output for video and music playback.
Provides HDMI audio and video signals to an HDMI compatible monitor or television.
Provides power to the device from cradles and cables and provides USB client and host communications.
Connects to mono headphones (3-wire, 2.5 mm plug).
Provides operating power to the ET1.
Releases the battery for removal.
Indicates battery charge state.
Opens the scan application (default). Programmable.
MN000022A01 - May 2013 1-3
ET1 Enterprise Tablet User Guide
1.2 Unpacking
Carefully remove all protective material from the ET1 and save the shipping container for later storage and shipping.
Verify the following items are in the box:
• ET1 Enterprise Tablet with 4 GB micro secure digital (SD) card installed
• Lithium-ion battery
• Quick Start Guide
• Regulatory Guide.
Inspect the equipment for damage. If any equipment is missing or damaged, contact the Motorola Solutions Global
Customer Support Center immediately. See
for contact information.
1.3 Setup
To start using the ET1 for the first time:
• Install SIM card in an ET1N2 with GSM (optional).
• Install the battery.
• Charge the ET1.
• Power on the ET1.
• Activate the ET1N2 on a mobile data network (optional).
1.3.1 Installing the SIM Card
ET1N2 only.
The ET1N2 requires an activated SIM card. Obtain the card from a service provider.
MN000022A01 - May 2013 1-4
1.3.2 Installing the Battery
Procedure Steps
1 Lift the access door.
Figure 1-3 Installing SIM Card
2 Insert SIM card into the SIM holder with the contacts facing down and the cut edge facing away from the holder.
3 Close the access door.
1.3.2 Installing the Battery
Ensure that the correct battery is used with the ET1. On the ET1N0 use either the 4620 mAh battery, p/n 82-149690-xx or the 5640 mAh battery, p/n 82-158261-xx. On the ET1N2 use only the 5640 mAh battery, p/n 82-158261-xx.
To install the battery:
MN000022A01 - May 2013 1-5
ET1 Enterprise Tablet User Guide
Procedure Steps
1 Align the tracks on the side of the battery with the rails in the battery compartment.
2 Push the battery in until the battery release latch snaps into place.
3 If the battery is charged, press and hold the Power button for two seconds until the splash screen appears.
Figure 1-4 Inserting the Battery
1
2
1.
Rails
2.
Battery Tracks
1.3.3 Charging the Battery
Ensure that you follow the guidelines for battery safety described in
8.2 Battery Safety Guidelines, page 8-1
.
MN000022A01 - May 2013 1-6
1.3.3.1 Charging the Main Battery
1.3.3.1 Charging the Main Battery
Before using the ET1 for the first time, charge the main battery until the Battery Charge light emitting diode
(LED) turns solid green (see
Table 1-2 Battery Charge LED Status
for charge status indications). To charge the
ET1, use a cable or a cradle with the appropriate power supply. For information about the accessories available for the ET1, see
The ET1 is equipped with a memory backup battery that automatically charges from the fully-charged main battery. When using the ET1 for the first time, the backup battery requires approximately 40 hours to fully charge.
This is also true any time the backup battery is discharged, which occurs when the main battery is removed for several hours. The backup battery retains random access memory (RAM) data in memory for at least 15 minutes
(at room temperature) when the ET1’s main battery is removed, when Battery swap feature is used. When the
ET1 reaches a very low battery state, the combination of main battery and backup battery retains RAM data in memory for at least 36 hours.
For cable and cradle setup and charging procedures refer to the ET1 Enterprise Tablet Integrator Guide.
• USB/Charge Cable
• Single-slot USB Docking Cradle
• Four-slot Charge Only Docking Cradle.
To charge the main battery:
1.
Connect the charging accessory to the appropriate power source. See
for more information.
2.
Insert the ET1 into a cradle or attach to a cable. The ET1 begins charging. The Battery Charge LEDs blink yellow
while charging, then turns solid green when fully charged. See Table 1-2 Battery Charge LED Status
for charging indications.
The battery charges in less than six hours.
Table 1-2 Battery Charge LED Status
Status
Off
Indications
ET1 is not inserted correctly in the cradle. ET1 is not connected to a power source. Charger or cradle is not powered.
ET1 is charging.
Slow Blinking Yellow (3 blinks every 2 seconds)
Solid Green
Fast Blinking yellow (2 blinks/second)
Charging complete.
Charging error, e.g.:
Flashes Yellow three times when
Power button pressed
Fast blinking Yellow (when Power button pressed)
• Temperature is too low or too high.
• Charging has gone on too long without completion (typically eight hours).
Critical battery state. Battery too low to boot device.
Battery over-temperature condition. Device shuts down. Battery will not charge until temperature returns to normal operating value.
MN000022A01 - May 2013 1-7
ET1 Enterprise Tablet User Guide
1.3.3.2 Charging Temperature
Charge batteries in temperatures from 0 °C to 40 °C (32 °F to 104 °F). Note that charging is intelligently controlled by the ET1. To accomplish this, for small periods of time, the ET1 or accessory alternately enables and disables battery charging to keep the battery at acceptable temperatures. The ET1 or accessory indicates when charging is disabled due to abnormal temperatures via its LED. See
Table 1-2 Battery Charge LED Status .
1.3.3.3 Charging Spare Batteries
See
for information on using accessories to charge spare batteries.
1.3.4 Powering On the ET1
Press the Power button until the Battery Charge LED flashes three times. The splash screen displays for about a minute as the ET1 initializes its flash file system. Note that these windows also appear upon reset.
1.3.5 WAN Activation
ET1N2 only.
In order to use the WAN radio for data communication, the ET1N2 must be activated on the service provider’s network. By default, the ET1N2 is configured for a GSM network. To activate on a CDMA network, manual configuration is required.
Refer to the ET1 Enterprise Tablet Integrator Guide for detailed WAN configuration information.
1.3.5.1 GSM Activation
When the ET1N2 turns on it automatically configures for the network. If the SIM card requires a PIN, the PIN screen appears. Enter the PIN and touch OK .
1.3.5.2 CDMA Activation
Prior to using the ET1N2 on a CDMA network, the ET1 must be registered with the service provider. Contact the service provider to set up an account and provide the MEID number (located under the battery).
By default, the ET1N2 is configured for a GSM network. To activate on a CDMA network:
MN000022A01 - May 2013 1-8
1.4 Replacing the Battery
Procedure Steps
1 Touch .
2 Touch More...
.
3 Touch Mobile networks .
4 Touch Technology preferences .
5 Touch Network mode .
6 In the Network mode menu, select either Sprint or Verizon . The ET1 switches the modem firmware and the
Activation Dialog box appears.
Figure 1-5 Activation Screen
7 Touch Activate . The ET1N2 begins the activation process. If the activation is unsuccessful, contact the service provider.
1.4 Replacing the Battery
Do not remove the microSD card while in Battery Swap mode.
Ensure that the Battery Swap mode procedures are followed, otherwise the backup battery will deplete quickly and on the ET1N2, SIM card data corruption might occur.
To replace the battery:
MN000022A01 - May 2013 1-9
ET1 Enterprise Tablet User Guide
Procedure Steps
1 Press the Power button until the menu displays.
2 Touch Battery Swap . The Scan LED lights red.
3 Wait until the Scan LED turns off.
4 Press thumb against the side of the ET1 and battery. Using the index and middle fingers, move the battery release latch toward thumb.
5 Pull the battery out of the battery compartment.
Figure 1-6 Removing the Battery
6 Align the tracks on the side of the replacement battery with the rails in the battery compartment.
7 Push the battery in until the battery release latch snaps into place.
8 Press the Power button to turn on the ET1.
1.5 Replacing the microSD Card
1-10
For proper electrostatic discharge (ESD) precautions to avoid damaging the SD card. Proper
ESD precautions include, but not limited to, working on an ESD mat and ensuring that the user is properly grounded.
Changing the microSD card can change the functionality of the ET1.
To replace the microSD card:
MN000022A01 - May 2013
1.5 Replacing the microSD Card
Procedure Steps
1 Press the Power button until the menu displays.
2 Touch Power off .
3 Touch OK .
4 Wait for the ET1 to power off completely.
5 Press thumb against the side of the ET1 and battery. Using the index and middle fingers, move the battery release latch toward thumb.
6 Pull the battery out of the battery compartment.
7 Lift the access door.
Figure 1-7 Lift Access Door
8 Remove the microSD card from the card holder.
9 Align the replacement microSD card with the card holder. Ensure that the contacts on the card are facing down and toward the card holder.
MN000022A01 - May 2013 1-11
ET1 Enterprise Tablet User Guide
10 Insert the microSD card into the card holder.
Figure 1-8 Insert microSD Card
11 Close the access door.
Figure 1-9 Close Access Door
12 Align the tracks on the side of the replacement battery with the rails in the battery compartment.
13 Push the battery in until the battery release latch snaps into place.
14 Press the Power button to turn on the ET1.
1.6 Handstrap
Use the optional 360-degree rotatable handstrap to securely hold the ET1 while working. Refer to the ET1
Enterprise Tablet Integrator Guide for information on installing the handstrap.
Rotate the handstrap for landscape or portrait viewing.
MN000022A01 - May 2013 1-12
Figure 1-10 Rotate Handstrap 360 Degrees
Insert hand into the handstrap and tighten strap.
Figure 1-11 Hand in Handstrap
1.7 Battery Management
1.7 Battery Management
Prior to checking the battery charge level, remove the ET1 from any AC power source (cradle or cable).
To check the charge status of the main battery, touch > About device > Status .
Battery status indicates that the battery is discharging and Battery level lists the battery charge (as a percentage of fully charged).
MN000022A01 - May 2013 1-13
ET1 Enterprise Tablet User Guide
1.7.1 Monitor Battery Usage
The Battery screen lists which applications consume the most battery power. Also use it to turn off applications that were downloaded if they are consuming too much power.
Touch > Battery .
Figure 1-12 Battery Screen
The Battery screen lists the applications using the battery. The discharge graph at the top of the screen shows the rate of the battery discharge since last charged (short periods of time when connected to a charger are shown as thin green lines at the bottom of the chart), and how long it has been running on battery power.
Touch an application in the Battery screen to display details about its power consumption. Different applications display different information. Some applications include buttons that open screens with settings to adjust power use.
1.7.2 Low Battery Notification
When the battery charge drops below 20%, the ET1 displays a notice to connect the ET1 to power.
MN000022A01 - May 2013 1-14
1.7.3 Battery Optimization
Figure 1-13 Low Battery Notification
The user should replace the battery or charge the ET1 using one of the charging accessories.
When the battery charge drops below 10%, the ET1 goes into critical suspend mode to save data. The screen turns off. If the Power button is pressed, the Charge LED flashes yellow.
The user must replace the battery or charge the ET1 using one of the charging accessories to retain data.
1.7.3 Battery Optimization
Observe the following battery saving tips:
• Leave the ET1 connected to AC power at all times when not is use.
• Set the screen to turn off after a short period of non-use.
• Reduce screen brightness.
• Turn off all wireless radios when not in use. Note that the global positioning system (GPS) receiver is only turned on when a GPS application is using GPS.
• Turn off automatic syncing for Email, Calendar, Contacts and other applications.
• Use the Power Control widget to check and control the status of radios, the screen brightness, and syncing.
• Minimize use of applications that keep the ET1 from suspending, for example, music, GPS and video applications.
1.7.3.1 Changing the Screen Timeout Setting
To set the ET1 to turn off after a short period of non-use:
MN000022A01 - May 2013 1-15
ET1 Enterprise Tablet User Guide
Procedure Steps
1 Touch .
2 Touch Display .
3 Touch Sleep .
4 Select a value from the Sleep window. Options:
• 15 seconds
• 30 seconds
• 1 minute (default)
• 2 minutes
• 5 minutes
• 10 minutes
• 30 minutes
5 Touch .
1.7.3.2 Changing the Brightness Setting
To change the brightness setting in order to conserve more battery power:
1-16 MN000022A01 - May 2013
1.7.3.3 Turning Off the Radios
Procedure Steps
1 Touch .
2 Touch Display .
3 Touch Brightness .
4 If the Automatic Brightness checkbox is set, touch the checkbox to disable.
5 Move the slider to the left to reduce the brightness.
6 Touch OK .
7 Touch .
1.7.3.3 Turning Off the Radios
To turn off all the radios:
Procedure Steps
1 Press the Power button until the menu appears.
2 Touch Airplane mode . The airplane icon appears in the Status bar indicating that all the radios are off.
1.8 Setting the Date and Time
The date and time are automatically synchronized using an NTP server when the ET1 is connected to a wireless network. The user is only required to set the time zone. Refer to the ET1 Enterprise Tablet Integrator Guide for more information on configuring the NTP server connection.
To set the date and time:
MN000022A01 - May 2013 1-17
ET1 Enterprise Tablet User Guide
Procedure Steps
1 Touch .
2 Touch Date & time .
3 Touch Select time zone .
4 Touch the time zone for the current location.
5 Touch .
1.9 Display Setting
The Display settings screen allows the user to set the following options:
• Brightness
• Screen rotation
• Sleep time
• Font size
1.9.1 Setting the Screen Brightness
To set the screen brightness:
1-18 MN000022A01 - May 2013
1.9.2 Setting Screen Rotation
Procedure Steps
1 Touch .
2 Touch Display .
3 Touch Brightness .
Figure 1-14 Brightness Dialog Box
4 In the Brightness dialog box, check the Automatic brightness checkbox to set the ET1 to automatically adjust the brightness using the built-in light sensor. Uncheck the checkbox to set the brightness manually. Use the slider to set a brightness level.
5 Touch OK .
6 Touch .
1.9.2 Setting Screen Rotation
The user can set the ET1 screen to rotate 90 degrees left or right.
MN000022A01 - May 2013 1-19
ET1 Enterprise Tablet User Guide
Procedure Steps
1 Touch .
2 Touch Display .
3 In the Display settings screen, check Auto-rotate screen to set the ET1 to automatically switch orientation when the ET1 is rotated.
4 Touch .
1.9.3 Setting Screen Sleep
The user can set the ET1 display to turn off after a period of inactivity.
Procedure Steps
1 Touch .
2 Touch Display .
3 Touch Sleep .
4 In the Sleep menu, select one of the sleep values.
• 15 seconds
• 30 seconds
• 1 minute (default)
• 2 minutes
• 5 minutes
• 10 minutes
• 30 minutes
5 Touch .
1.9.4 Setting Font Size
To set the size of the font in system applications:
MN000022A01 - May 2013 1-20
1.10 General Sounds Setting
Procedure Steps
1 Touch .
2 Touch Display .
3 Touch Font size .
4 In the Font size menu, select one of the font size values.
• Small
• Normal
• Large
• Huge
5 Touch .
1.10 General Sounds Setting
Use the Sounds settings to configure media and alarm volumes. Touch
Figure 1-15 Sounds Screen
> > Sounds .
• Volumes — Use to change the volume of media, ringtones and notifications and alarms.
MN000022A01 - May 2013 1-21
ET1 Enterprise Tablet User Guide
Figure 1-16 Volumes Dialog Box
• Call Ringtone and Vibrate
– Vibrate when ringing - Check to make the ET1 vibrate when a call is received.
• System
– Default notification - Touch to select a sound to play for all system notifications.
– Touch sounds - Check to play a sound when making screen selections.
– Screen lock sounds - Check to play a sound when locking and unlocking the screen.
– Vibrate on touch - Check to have the ET1 vibrate when touching soft keys and on certain screen interactions.
1-22 MN000022A01 - May 2013
2
Using the ET1
This chapter describes the screens, status and notification icons, and controls on the ET1, and provides basic instructions for using the ET1.
2.1 Home Screen
The Home screen displays when the ET1 turns on. Depending upon the configuration, the Home screen might appear different. Contact your system administrator for more information.
After a suspend or screen time-out, the Home screen displays with the lock icon. Touch and slide touches . For screen locking information see
2.11 Un-Locking the Screen, page 2-16 .
Figure 2-1 Home Screen up until it
Table 2-1 Home Screen Items
Item Description
1 — Status Bar Displays the time, status icons (right side), and notification icons (left side). For more information see
and
2.2.3 Managing Notifications, page 2-5 .
2 — Browser Icon Opens the Browser application.
MN000022A01 - May 2013 2-1
ET1 Enterprise Tablet User Guide
Table 2-1 Home Screen Items (cont'd.)
Item
3 — All Apps
Icon
Description
Opens the APPS window.
4 — Settings Icon Opens the Settings window.
5 — Shortcut
Icons
6 — Widgets
Opens applications installed on the ET1. See
for more information.
2.3 Application Shortcuts and Widgets, page
Launches stand-alone applications that run on the Home screen. See
Shortcuts and Widgets, page 2-6
for more information.
The Home screen provides four additional screens for placement of widgets and shortcuts. Swipe the screen left or right to view the additional screens.
2.2 Status Bar
The Status bar displays the time, notification icons (left side) and status icons (right side).
Figure 2-2 Notification and Status Icons
1.
Notification icons
2.
Status icons.
If there are more notifications than can fit in the Status bar,
Open the Notifications panel to view all notifications and status.
displays indicating that more notifications exist.
2.2.1 Status Icons
lists Status icons that might appear in the Status Bar.
Table 2-2 Status Icons
Icon Description
Indicates that GPS is on.
Indicates that the ET1 is receiving location data from GPS.
Indicates that Bluetooth is on.
MN000022A01 - May 2013 2-2
MN000022A01 - May 2013
2.2.1 Status Icons
Table 2-2 Status Icons (cont'd.)
Icon Description
Indicates that the ET1 is connected to a Bluetooth device.
Indicates that the Alarm is active.
Indicates that all sounds except media and alarms are silenced and vibrate mode is active.
Indicates that the ringer is silenced.
Connected to a Wi-Fi network.
No Wi-Fi signal.
Indicates that the battery charge is very low.
Indicates that the battery charge is low.
Indicates that the battery is partially drained.
Indicates that the battery is fully charged.
Indicates that the battery is charging.
Indicates that the Airplane Mode is active. All radios are turned off.
Mobile network signal strength (ET1N2 only).
No mobile network signal (ET1N2 only).
Connected to an EDGE or EVD0 network (ET1N2 only).
Connected to a 3G network (ET1N2 only).
Connected to an HSPA network (ET1N2 only).
Connected to a 1X CDMA network (ET1N2 only).
2-3
ET1 Enterprise Tablet User Guide
Table 2-2 Status Icons (cont'd.)
Icon Description
Roaming from a network (ET1N2 only).
No SIM card installed (ET1N2 only).
2.2.2 Notification Icons
lists the possible notification icons. See
2.2.3 Managing Notifications, page 2-5
for information about responding to these notifications. In addition to these icons, installed applications may display their own notification icons.
Table 2-3 Notification Icons
Icon Description
Indicates that more notifications are available for viewing.
Indicates that data is syncing.
Indicates an upcoming event.
Indicates that an open Wi-Fi network is available.
Indicates that a song is playing.
Indicates that a problem with sign-in or sync has occurred.
Indicates that the ET1 is uploading data.
Indicates that the microSD card is almost full.
Indicates that the ET1 is downloading data when animated and download is complete when static.
Indicates that the ET1 is connected via USB cable.
Indicates that the ET1 is connected to or disconnected from virtual private network (VPN).
MN000022A01 - May 2013 2-4
2.2.3 Managing Notifications
Table 2-3 Notification Icons (cont'd.)
Icon Description
Preparing SD card.
Indicates that USB debugging is enabled on the ET1.
Indicates that the MultiUser feature is enabled.
Indicates that a new user is logging in.
Indicates that the ET1 has received a text message (ET1N2 only).
2.2.3 Managing Notifications
Notification icons report the arrival of new messages, calendar events, and alarms, as well as ongoing events. When a notification occurs, an icon appears in the Status bar with a brief description. See
.
Open the Notifications Panel to view a list of all the notifications.
To open the Notification Panel drag the Status bar down from the top of the screen.
Figure 2-3 Notification Panel
To respond to a notification, open the Notifications Panel and then touch a notification. The Notifications Panel closes and the subsequent activity is dependent on the notification.
MN000022A01 - May 2013 2-5
ET1 Enterprise Tablet User Guide
To clear all notifications, open the Notifications Panel and then touch removed. Ongoing notifications remain in the list.
. All event-based notifications are
To close the Notification Panel, drag the bottom of the Notifications Panel to the top of the screen or touch .
2.3 Application Shortcuts and Widgets
Application shortcuts placed on the Home screen allow quick and easy access to applications. Widgets are self-contained applications placed on the Home screen to access frequently used features.
2-6 MN000022A01 - May 2013
2.3.1 Adding an Application or Widget to the Home Screen
2.3.1 Adding an Application or Widget to the Home Screen
Procedure Steps
1 Go to the desired Home screen.
2 Touch .
3 Swipe right, if necessary, to find the application icon or widget.
4 Touch and hold the icon or widget until the Home screen appears.
5 Position the icon on the screen and then release.
2.3.2 Moving Items on the Home Screen
Procedure Steps
1 Touch and hold the item until it floats on the screen.
2 Drag the item to a new location. Pause at the edge of the screen to drag the item onto an adjacent Home screen.
3 Lift finger to place the item on the Home screen.
2.3.3 Removing an App or Widget from the Home Screen
Procedure Steps
1 Go to the desired Home screen.
2 Touch and hold the application shortcut or widget icon until it floats on the screen.
3 Drag the icon to in the top left corner of the screen and then release.
2.4 Folders
Use Folders to organize similar applications together. Touch the folder to open and display items in the folder.
MN000022A01 - May 2013 2-7
ET1 Enterprise Tablet User Guide
2.4.1 Creating Folders
Procedure Steps
1 Go to the desired Home screen.
2 Place at least two application shortcuts on the Home screen.
3 Touch and hold a shortcut until it floats on the screen.
4 Move the icon over another icon. A blue circle appears around the icons.
Figure 2-4 Stacked Shortcut Icons
5 Lift finger to stack the icons. The shortcut icons appears over a black circle.
Figure 2-5 Unnamed Folder
2.4.2 Naming Folders
Procedure Steps
1 Touch the folder.
Figure 2-6 Open Folder
2-8
2 Touch the title area and enter a folder name using the keyboard.
3 Touch Done .
MN000022A01 - May 2013
2.4.3 Removing a Folder From the Home Screen
4 Touch anywhere on the Home screen to close the folder. The folder name appears under the folder.
Figure 2-7 Renamed Folder
2.4.3 Removing a Folder From the Home Screen
Procedure Steps
1 Touch and hold the folder icon until it floats on the screen.
2 Drag the icon to in the top left corner of the screen and then release.
2.5 Home Screen Wallpaper
Use of Live Wallpaper may reduce battery life.
MN000022A01 - May 2013 2-9
ET1 Enterprise Tablet User Guide
2.5.1 Change the Home Screen Wallpaper
Procedure Steps
1 Touch and hold on the Home screen until the Choose Wallpaper from menu appears.
2 Touch Gallery , Live wallpapers or Wallpapers .
• Gallery - Select to use an image stored on the device.
• Live wallpapers - Select to use an animated wallpaper image.
• Wallpapers - Select to use a wallpaper image.
3 Touch Save or Set wallpaper .
2.6 Moving Items on the Home Screen
Procedure Steps
1 Touch and hold the item until it enlarges.
2 Drag the item to a new location. Pause at the edge of the screen to drag the item onto an adjacent Home screen.
3 Lift finger to place item.
2.7 Removing Items from the Home Screen
Procedure Steps
1 Touch and hold the item until it enlarges.
2 Drag the item over in the top left corner of the screen and then release..
2.8 Using the Touchscreen
Use the multi-touch sensitive screen to operate the device.
• Touch - Touch to:
– select items on the screen
– type letters and symbols using the on-screen keyboard
2-10 MN000022A01 - May 2013
2.9 Using the On-screen Keyboard
– press on-screen buttons.
• Touch and Hold - Touch and hold:
– an item on the Home screen to move it to a new location or to the trash.
– the Launcher icon or dots on the Home screen to open the Home screen thumbnails.
– an item in the Launcher to create a shortcut on the Home screen.
– the Home screen to open a menu for customizing the Home screen.
– an empty area on the Home screen until the menu appears.
• Drag - Touch and hold an item for a moment and then move finger on the screen until reaching the new position.
• Swipe - Move finger up and down or left and right on the screen to:
– unlock the screen
– view additional Home screens
– view additional application icons in the Launcher window
– view more information on an application’s screen.
• Double-tap - Tap twice on a web page, map, or other screen to zoom in and out.
• Pinch - In some applications, zoom in and out by placing two fingers on the screen and pinching them together (to zoom out) or spreading them apart (to zoom in).
2.9 Using the On-screen Keyboard
Use the on-screen keyboard to enter text in a text field. To configure the keyboard settings, touch select keyboard settings .
and then
Editing Text
Edit entered text and use menu commands to cut, copy, and paste text within or across applications. Some applications do not support editing some or all of the text they display; others may offer their own way to select text.
Entering Numbers, Symbols and Special Characters
To enter numbers and symbols:
• Touch and hold one of the top-row keys until a menu appears then select a number. Keys with alternate characters display an ellipsis ( ... ) below the character.
• Touch and hold the Shift key with one finger, touch one or more capital letters or symbols to enter them, and then lift both fingers to return to the lowercase keyboard.
• Touch to switch to the numbers and symbols keyboard.
• Touch the ALT key on the numbers and symbols keyboard to view additional symbols.
To enter special characters, touch and hold a number or symbol key to open a menu of additional symbols.
• A larger version of the key displays briefly over the keyboard.
MN000022A01 - May 2013 2-11
ET1 Enterprise Tablet User Guide
• Keys with alternate characters display an ellipsis ( ... ) below the character.
2.9.1 Entering Text
Enter text using the on-screen keyboard:
Some apps open the keyboard automatically. In others, open it by touching where to type.
Figure 2-8 On-screen Keyboard
2-12 MN000022A01 - May 2013
2.10 Applications
Procedure Steps
1 Touch a text field. The on-screen keyboard appears.
2 Touch keys on the keyboard to enter text.
The entered text appears in the text field and in the suggestion strip. When the keyboard has a suggestion, the word is underlined in the text field and the suggestions appear in blue. The boldfaced suggestion at the center of the strip is the keyboard’s best suggestion. Drag the strip to the left to view additional suggestions.
3 Press space or a punctuation mark to enter the boldfaced suggested word.
4 Touch
5 Touch to erase characters to the left of the cursor.
to close the keyboard.
2.10 Applications
The APPS screen displays icons for all installed applications.
lists the default applications on the ET1.
Refer to the ET1 Enterprise Tablet Integrator Guide for information on installing and uninstalling application.
Table 2-4 ET1 Default Applications
Icon Description
Browser - Use to access the Internet or intranet.
Calculator - Provides the basic and scientific arithmetic functions.
Calendar - Use to manage events and appointments.
Camera - Take photos or record videos. See
for more information.
Clock - Use to schedule alarms for appointments or as a wake-up.
DataWedge - Enables data capture using the camera or optional scanner.
MN000022A01 - May 2013 2-13
ET1 Enterprise Tablet User Guide
Table 2-4 ET1 Default Applications (cont'd.)
Icon Description
Downloads - lists all downloads files.
DWDemo - Provides a way to demonstrate the data capture features using the Camera,
Scanning Module or Magnetic Stripe Reader.
Email - Use to send and receive email.
ET1 User Guide - Displays the On-device User Guide.
File Browser - Organize and manage files on the ET1. See
for more information.
Gallery - Use to view photos stored on the microSD card. See
for more information.
GPS Status 2 - Use to configure location services.
Messaging - Use to send and receive SMS messages on ET1N2 only.
MSP Agent - Enables management of the ET1 from an MSP server. Requires the purchase of an appropriate MSP client license per device to suit the level of management functionality required.
Music - Play music stored on the microSD card.
Contacts - Use to manage contact information.
2-14 MN000022A01 - May 2013
2.10 Applications
Table 2-4 ET1 Default Applications (cont'd.)
Icon Description
Rapid Deployment - Allows the ET1 to stage a device for initial use by initiating the deployment of settings, firmware and software. Requires the purchase of an MSP client license per device.
RIL Log - Use to capture debugging information. (ET1N2 only).
Search - Use the search engine to search the Internet and the ET1.
Settings - Use to configure the ET1. For more information, refer to the ET1 Enterprise
Tablet Integrator Guide .
Sound Recorder - Use to record audio.
AppLock Administrator - Use to configure the Application Lock feature. This icon appears after the optional application is installed.
MultiUser Administrator - Use to configure the MultiUser feature. This icon appears after the optional application is installed.
Secure Storage Administrator - Use to configure the Secure Storage feature. This icon appears after the optional application is installed.
DWDemo - Provides a way to demonstrate the data capture features using the Camera,
Scanning Module or Magnetic Stripe Reader.
MN000022A01 - May 2013 2-15
ET1 Enterprise Tablet User Guide
2.10.1 Switching Between Recent Applications
Procedure Steps
1 Touch and hold . A screen appears with recently used applications.
Figure 2-9 Recently Used Applications
2 Touch an application to open it or press to return to the current screen.
3 Swipe an application up or down to remove from the list.
2.11 Un-Locking the Screen
Use the Lock screen to protect access to data on the ET1. Some email account require locking the screen. Refer to the ET1 Enterprise Tablet Integrator Guide for information on setting up the locking feature. The Locking feature functions differently in Single User mode or Multiple User mode.
2.11.1 Single User Mode
When locked, a pattern, PIN or password is required to unlock the device. Press the Power button to lock the screen. The device also locks after a pre-defined time-out.
Press and release the Power button to wake the device.
The Lock screen displays. Touch and slide up until it touches . If the Pattern screen unlock feature is enabled, the Pattern screen appears instead of the Lock screen.
MN000022A01 - May 2013 2-16
2.11.1 Single User Mode
If the PIN or Password screen unlock feature is enabled, enter the PIN or password after unlocking the screen.
Figure 2-10 Lock Screen
Figure 2-11 PIN Screen
MN000022A01 - May 2013 2-17
ET1 Enterprise Tablet User Guide
Figure 2-12 Pattern Screen
Figure 2-13 Password Screen
2.11.2 MultiUser Mode
With MultiUser login, multiple users can log on to the device with each user having access to various applications and features. When enabled, the Login screen appears after powering on, resetting or after the device wakes from suspend mode.
MN000022A01 - May 2013 2-18
2.11.2.1 Multiuser Login
Procedure Steps
1 In the Login text field, enter the username.
Figure 2-14 Multiple user Log In Screen
2.11.2.1 Multiuser Login
2 In the Password text field, enter the password.
3 Touch OK . After a resume from suspend, the user must enter the password.
2.11.2.2 Multiuser Logout
Procedure Steps
1 Drag the Status Bar down from the top of the screen.
2 Touch MultiUser is active .
3 Touch Logout .
4 The Login screen appears.
MN000022A01 - May 2013 2-19
ET1 Enterprise Tablet User Guide
2.12 Resetting the Device
There are two reset functions, soft reset and hard reset.
2.12.1 Performing a Soft Reset
Perform a soft reset if applications stop responding.
Procedure Steps
1 Press and hold the Power button until the menu appears.
2 Touch Reset .
3 The device shuts down and then reboots.
2.12.2 Performing a Hard Reset
Performing a hard reset with a SIM card installed in the ET1N2 may cause damage or data corruption to the SIM card.
Perform a hard reset if the ET1 stops responding. To perform a hard reset:
Procedure Steps
1 Simultaneously press the Power, Left Scan/Action and Right Scan/Action buttons.
2 The ET1 shuts down and then reboots.
2.13 Wake-up Settings
The wake-up conditions define what actions wake up the ET1 after it has gone into suspend mode. The ET1 can go
into suspend mode by either pressing the Power button or automatically by a time-out settings.
list the default wake up conditions.
Table 2-5 Wake-up Default Settings
Condition for Wake-up
AC power is applied.
ET1 is inserted into a cradle.
Power Button
No
Yes
Automatic Time-out
Yes
Yes
MN000022A01 - May 2013 2-20
2.13.1 Waking the ET1
Table 2-5 Wake-up Default Settings (cont'd.)
Condition for Wake-up
ET1 is removed from a cradle.
ET1 is connected to a USB device.
ET1 is disconnected from a USB device.
Scan/Action button is pressed.
The screen is touched.
Bluetooth communication
Power Button
No
No
No
Yes
No
Yes
Automatic Time-out
No
Yes
Yes
Yes
No
Yes
2.13.1 Waking the ET1
If the ET1 is not used for a while, the screen dims and then darkens to conserve the battery.
The Lock screen displays. Touch and slide up until it touch . If the Pattern screen unlock feature is enabled, the Pattern screen appears instead of the Lock screen. See
2.11 Un-Locking the Screen, page 2-16
for more information.
2.14 File Browser
Use the File Browser application to view and mange files on the ET1.
To open File Browser , touch > .
MN000022A01 - May 2013 2-21
ET1 Enterprise Tablet User Guide
Figure 2-15 File Browser Screen
2-22
The address bar (1) indicates the current folder path. Touch the current folder path to manually enter a path and folder name.
Use (2) to select multiple files/folder.
Use (3) to view to the ET1 internal storage root folder.
Use (3) to view the microSD card root folder.
Use (4) to view the previous folder or to exit the application.
Touch and hold an item to perform an operation on that item. Select one of the options from the menu:
• Information - View detailed information about the file or folder.
• Move - Move the file or folder to a new location.
• Copy - Copy the select file.
• Delete - Delete the selected file.
• Rename - Rename the select file.
• Open as - Open the selected file as a specific file type.
Touch to open additional functionality:
• Touch > New Folder to create a new folder in the current folder.
• Touch > Search to search for a file or folder.
• Touch > Sort to sort the list by name, by type, by size or by date.
• Touch > Refresh to re-display the contents of the current folder.
• Touch > List View to change the folder view from tile to list format.
MN000022A01 - May 2013
2.15 Messaging
• Touch > Change Size to change the size of the icons: Large, Normal or Small.
2.15 Messaging
Messaging is only available on the ET1N2 configuration.
Use Messaging to exchange text messages (SMS) with other mobile devices.
2.15.1 Opening Messaging
To open the Messaging application touch > . The Messaging window opens.
• Touch NEW MESSAGE to start a new text message.
• Touch an existing message thread to open it.
2.15.2 Sending a Text Message
Procedure Steps
1 On the Messaging screen, touch NEW MESSAGE .
2 In the To field, enter a mobile phone number or contact name.
3 Touch the Type message text box to start entering a message.
A text message is limited to 160 character.
If the user goes over that limit, multiple text messages are sent. If the user presses while composing a message, it’s saved as a draft in the Messaging window. Touch the message to resume composing it.
4 Touch .
The Message window opens, with the message after the user’s name. Responses appear in the window. As the user views and sends additional messages, a message thread is created
2.15.3 Responding to a Message
When a new message is received a notification appears and appears in the Status bar.
Pull down the Notification Shade and touch the message notification.
MN000022A01 - May 2013 2-23
ET1 Enterprise Tablet User Guide
The Message window appears.
Touch and hold a message until the Message options menu appears with number of options for working with the message and its sender’s information.
2.15.4 Forwarding a Message
Procedure Steps
1 Touch and hold a message until the Message options menu appears.
2 Touch Forward .
3 Enter a recipient for the message and edit the content.
4 Touch .
2.15.5 Locking a Message
Lock a message so it can not be deleted if the storage limits is reached. If the user tries to delete a thread that contains a locked message, the user is asked to confirm deleting it.
2-24 MN000022A01 - May 2013
2.15.6 Viewing Message Details
Procedure Steps
1 Touch and hold a message in a Message window until the Message options menu appears.
2 Touch Lock . A lock icon appears to the right of the message.
To unlock a message, Touch and hold a message until the Message options menu appears. Touch Unlock .
2.15.6 Viewing Message Details
Procedure Steps
1 Touch and hold a message until the Message options menu appears.
2 Touch View details . The Message details dialog box appears.
3 Touch the screen anywhere outside the dialog box to close.
2.15.7 Deleting a Message Thread
Procedure Steps
1 Touch and hold the message thread until the a menu appears.
2 Touch Delete thread .
2.15.8 Messaging Settings
To change Messaging settings touch > > > Settings .
• STORAGE
– Delete old messages - Check to delete older messages in a thread when the text message limit is reached.
Uncheck to keep all messages.
– Text message limit - Touch to set the number of messages to save per thread of text messages. When the limit is reached, older messages are deleted if Delete old messages is checked.
• TEXT (SMS) MESSAGES
– Manage SIM card messages - View text messages stored on a SIM card.
• NOTIFICATIONS
– Notifications - Check to receive a notification whenever the ET1 receives a new message.
MN000022A01 - May 2013 2-25
ET1 Enterprise Tablet User Guide
– Choose ringtone - Opens a dialog box to select the ringtone to sound when the ET1 receives a new message notifications.
– Vibrate - Opens a dialog box to set the ET1 to vibrate whenever it receives a new message notification.
Options: Always , Only when silent or Never (default).
2-26 MN000022A01 - May 2013
3
Data Capture
The ET1 offers the following data capture options:
• Scanning Module
• Scanning/MSR Module
• integrated digital camera
• optional CS3070 Bluetooth laser scanner.
DataWedge is installed and enabled on the ET1 by default.
3.1 Scanning Modules
The ET1 with an integrated Scan Module has the following features:
• Omnidirectional reading of a variety of bar code symbologies, including the most popular linear, postal, PDF417, and 2D matrix code types.
• Advanced intuitive laser aiming cross-hair for easy point-and-shoot operation.
The modules uses digital camera technology to take a digital picture of a bar code, stores the resulting image in its memory, and executes state-of-the-art software decoding algorithms to extract the data from the image.
3.1.1 Operational Modes
The device with an integrated imager supports two modes of operation, listed below. Activate each mode by pressing a scan button.
• Decode Mode : In this mode, the device attempts to locate and decode enabled bar codes within its field of view.
The imager remains in this mode as long as the user holds the scan button, or until it decodes a bar code.
To enable Pick List Mode, configure in DataWedge.
• Pick List Mode : This mode allows the user to selectively decode a bar code when more than one bar code is in the device’s field of view. To accomplish this, move the aiming crosshair over the required bar code to decode only this bar code. This feature is ideal for pick lists containing multiple bar codes and manufacturing or transport labels containing more than one bar code type (either 1D or 2D).
MN000022A01 - May 2013 3-1
ET1 Enterprise Tablet User Guide
3.2 Digital Camera
The device with an integrated camera based bar code scanning solution has the following features:
• Omnidirectional reading of a variety of bar code symbologies, including the most popular linear, postal, QR,
PDF417, and 2D matrix code types.
• Cross-hair reticle for easy point-and-shoot operation.
• Picklist mode to decode a particular bar code from many in the field of view.
The solution uses the advanced camera technology to take a digital picture of a bar code, and executes state-of-the-art software decoding algorithms to extract the data from the image.
3.3 Laser Scanning
The optional CS3070 scanner has the following features:
• Reading of a variety of bar code symbologies, including the most popular linear, postal, and 1-D code types.
• Intuitive aiming for easy point-and-shoot operation.
3.4 Scanning Considerations
Typically, scanning is a simple matter of aim, scan, and decode and a few quick trial efforts master it. However, consider the following to optimize scanning performance:
• Range
– Any scanning device decodes well over a particular working range — minimum and maximum distances from the bar code. This range varies according to bar code density and scanning device optics.
– Scanning within range brings quick and constant decodes; scanning too close or too far away prevents decodes.
Move the scanner closer and farther away to find the right working range for the bar codes being scanned.
• Angle
– Scan angle is important for promoting quick decodes. When laser beams reflect directly back into the scanner from the bar code, this specular reflection can “blind” the scanner.
– To avoid this, scan the bar code so that the beam does not bounce directly back. But do not scan at too sharp an angle; the scanner needs to collect scattered reflections from the scan to make a successful decode.
Practice quickly shows what tolerances to work within.
• Hold the device farther away for larger symbols.
• Move the device closer for symbols with bars that are close together.
Scanning procedures depend on the application and device configuration. An application may use different scanning procedures from those described.
MN000022A01 - May 2013 3-2
3.5 Bar Code Capture with Scanning or Scanning/MSR Module
3.5 Bar Code Capture with Scanning or Scanning/MSR
Module
Procedure Steps
1 Ensure that an application is open on the ET1 and a text field is in focus (text cursor in text field).
2 Point the top of the ET1 at a bar code.
Figure 3-1 Bar Code Scanning
MN000022A01 - May 2013 3-3
ET1 Enterprise Tablet User Guide
3 Press and hold either Scan/Action button.
The red laser aiming pattern turns on to assist in aiming. Ensure the bar code is within the area formed by the cross-hairs in the aiming pattern. The aiming dot is used for increased visibility in bright lighting conditions.
The Scan/Decode LED lights red to indicate that scanning is in process, then lights green, a beep sounds and the
ET1 vibrates, by default, to indicate the bar code was decoded successfully. Note that when the ET1 is in Pick
List Mode, the ET1 does not decode the bar code until the center of the crosshair touches the bar code.
Figure 3-2 Aiming Pattern
Figure 3-3 Pick List Mode with Multiple Bar Codes in Aiming Pattern
4 Release the scan button.
5 The captured data appears in the text field.
3.6 Bar Code Capture with Integrated Camera
Procedure Steps
1 Ensure that an application is open on the ET1 and a text field is in focus (text cursor in a text field).
2 Aim the rear-facing camera at a bar code.
MN000022A01 - May 2013 3-4
3.7 Bar Code Capture with CS3070 Bluetooth Scanner
3 Press and hold either Scan/Action button. By default, a preview window appears. The Decode light emitting diode (LED) lights red to indicate that data capture is in process.
Figure 3-4 Sample Scan Application with Preview Window
4 Move the ET1 until the bar code is centered.
5 The Decode LED lights green, a beep sounds and the ET1 vibrates, by default, to indicate the bar code was decoded successfully.
6 The captured data appears in the text field.
3.7 Bar Code Capture with CS3070 Bluetooth Scanner
The CS3070 Bluetooth scanner captures bar code data, and transmits it to the ET1 via Bluetooth. The scanner supports Bluetooth human interface device (HID) connection to the ET1 where the scanner emulates a keyboard, as well as Serial Port Profile (SPP) connection where the scanner behaves as if there is a serial connection. See the ET1
Enterprise Tablet Integrator Guide for setup and configuration information.
Figure 3-5 CS3070 Bluetooth Scanner
1
5
1.
Bluetooth Button/LED
2.
Delete Button
3.
Scan Button
4
MN000022A01 - May 2013
3
2
3-5
ET1 Enterprise Tablet User Guide
4.
LED
5.
Exit Window
Procedure Steps
1 Ensure that an application is open on the ET1 and a text field is in focus (text cursor in a text field).
2 Aim the scanner at the bar code.
3 Press the scan (+) button.
Figure 3-6 CS3070 Scanning
4 Ensure the scan line crosses every bar and space of the symbol.
Figure 3-7 Linear Scanner Aiming Pattern
5 The scanner beeps and the LED turns green to indicate a successful decode.
6 The captured data appears in the text field.
3.8 Reading Magnetic Stripe Cards with
Scanning/MSR Module
Use the Scanning/MSR Module to read magnetic stripe cards.
3-6 MN000022A01 - May 2013
Procedure Steps
1 Ensure that MSR input is enabled in DataWedge and the cursor is in a text field.
2 Align the magnetic stripe on the card toward the display and swipe the card in either direction.
Figure 3-8 Swiping a Magnetic Stripe Card
3.9 DataWedge
3 The captured data appears in the text field.
3.9 DataWedge
DataWedge is a utility that adds advanced bar code scanning capability to any application without writing code. It runs in the background and handles the interface to both built-in and attached bar code scanners. The captured bar code data is converted to keystrokes and sent to the target application as if it was typed on the keypad.
MN000022A01 - May 2013 3-7
ET1 Enterprise Tablet User Guide
To configure DataWedge refer to the TC55 Integrator Guide .
3.9.1 Enabling DataWedge
To enable DataWedge:
Procedure Steps
1 Touch .
2 Touch . The DataWedge Profiles window appears.
3 Touch .
4 Touch Settings .
5 Touch the DataWedge enabled checkbox. A blue checkmark appears in the checkbox indicating that
DataWedge is enabled.
6 Touch .
3.9.2 Disabling DataWedge
To disable DataWedge:
MN000022A01 - May 2013 3-8
3.9.3 DataWedge Configuration
Procedure Steps
1 Touch .
2 Touch . The DataWedge Profiles window appears.
3 Touch .
4 Touch Settings .
5 Touch the DataWedge enabled checkbox. The blue checkmark disappears from the checkbox indicating that
DataWedge is disabled.
6 Touch .
3.9.3 DataWedge Configuration
To configure DataWedge see the ET1 Enterprise Tablet Integrator Guide .
MN000022A01 - May 2013 3-9
4
WLAN
Wireless local area networks (WLANs) allow the ET1 to communicate wirelessly inside a building. Before using the ET1 on a WLAN, the facility must be set up with the required hardware to run the WLAN (sometimes known as infrastructure). The infrastructure and the ET1 must both be properly configured to enable this communication.
Refer to the documentation provided with the infrastructure (access points (APs), access ports, switches or Radius servers) for instructions on how to set up the infrastructure.
Once the infrastructure is set up to enforce the chosen WLAN security scheme, use the Wi-Fi settings configure the
ET1 to match the security scheme.
Turn off Wi-Fi when not using it, to extend the life of the battery.
The Status Bar displays icons that indicate Wi-Fi network availability and Wi-Fi status. See
more information.
4.1 Connecting to a Wi-Fi Network
Procedure Steps
1 Touch
2 Touch Wi-Fi .
3 Slide the Wi-Fi switch to the On position. The ET1 searches for WLANs in the area and displays them in the list. Open networks are indicated with and secure networks are indicated with .
4 Scroll through the list and touch the desired WLAN network.
5 For open networks, the ET1 automatically connects to the network.
For secure networks, enter the required password or other credentials then touch Connect . See the system administrator for more information
The ET1 obtains a network address and other required information from the network using the dynamic host configuration protocol (DHCP) protocol. To configure the ET1 with a fixed internet protocol (IP) address, see the ET1 Enterprise Tablet Integrator Guide .
6 When the ET1 connects to the network, the network name appears at the top of the list and Connected appears below the network name.
MN000022A01 - May 2013 4-1
5
Bluetooth
Bluetooth-equipped devices can communicate without wires, using frequency-hopping spread spectrum (FHSS) radio frequency (RF) to transmit and receive data in the 2.4 GHz Industry Scientific and Medical (ISM) band
(802.15.1). Bluetooth wireless technology is specifically designed for short-range (10 meters (32.8 feet) ) communication and low power consumption.
Devices with Bluetooth capabilities can exchange information (e.g., files, appointments, and tasks) with other
Bluetooth enabled devices such as printers, access points, and other mobile devices.
5.1 Adaptive Frequency Hopping
Adaptive Frequency Hopping (AFH) is a method of avoiding fixed frequency interferers, and can be used with
Bluetooth voice. All devices in the piconet (Bluetooth network) must be AFH-capable in order for AFH to work.
There is no AFH when connecting and discovering devices. Avoid making Bluetooth connections and discoveries during critical 802.11b communications. AFH for Bluetooth consists of four main sections:
• Channel Classification - A method of detecting an interference on a channel-by-channel basis, or pre-defined channel mask.
• Link Management - Coordinates and distributes the AFH information to the rest of the Bluetooth network.
• Hop Sequence Modification - Avoids interference by selectively reducing the number of hopping channels.
• Channel Maintenance - A method for periodically re-evaluating the channels.
When AFH is enabled, the Bluetooth radio “hops around” (instead of through) the 802.11b high-rate channels.
AFH coexistence allows Motorola Enterprise Tablets to operate in any infrastructure.
The Bluetooth radio in this device operates as a Class 2 device power class. The maximum output power is 2.5 mW and the expected range is 10 meters (32.8 ft.). A definition of ranges based on power class is difficult to obtain due to power and device differences, and whether one measures open space or closed office space.
It is not recommended to perform Bluetooth wireless technology inquiry when high rate 802.11b operation is required.
5.2 Security
The current Bluetooth specification defines security at the link level. Application-level security is not specified.
This allows application developers to define security mechanisms tailored to their specific need. Link-level security occurs between devices, not users, while application-level security can be implemented on a per-user basis. The
Bluetooth specification defines security algorithms and procedures required to authenticate devices, and if needed, encrypt the data flowing on the link between the devices. Device authentication is a mandatory feature of Bluetooth while link encryption is optional.
Pairing of Bluetooth devices is accomplished by creating an initialization key used to authenticate the devices and create a link key for them. Entering a common personal identification number (PIN) in the devices being paired generates the initialization key. The PIN is never sent over the air. By default, the Bluetooth stack responds with no key when a key is requested (it is up to user to respond to the key request event). Authentication of Bluetooth
MN000022A01 - May 2013 5-1
ET1 Enterprise Tablet User Guide devices is based-upon a challenge-response transaction. Bluetooth allows for a PIN or passkey used to create other
128-bit keys used for security and encryption. The encryption key is derived from the link key used to authenticate the pairing devices. Also worthy of note is the limited range and fast frequency hopping of the Bluetooth radios that makes long-distance eavesdropping difficult.
Recommendations are:
• Perform pairing in a secure environment
• Keep PIN codes private and do not store the PIN codes in the device
• Implement application-level security.
5.3 Bluetooth Profiles
The ET1 supports the following Bluetooth services:
• Generic Access Profile (GAP) - Must support both Initiator and Acceptor roles.
• Service Discovery Protocol (SDP) - Supports both Local Device and Remote Device.
• Serial Port Profile (SPP) - Supports both Device A and Device B roles.
• Human Interface Device (HID) Profile - Supports Host role.
• Dial-up Networking (DUN) Profile - Supports connecting a computer to the ET1 to access the internet.
5.4 Bluetooth Power States
The Bluetooth radio is off by default.
• Suspend — When there is no active Bluetooth connections, the Bluetooth radio turns off.
If there is an active Bluetooth connection between the ET1 and another Bluetooth device and there is no data activity, the ET1 will time out. However, if the user presses the Power button on the ET1, the ET1 will suspend and upon receiving data from a remote Bluetooth device, the ET1 will wake from suspend mode. For example, Bluetooth scanner sending data to the ET1.
• Resume — When the ET1 resumes, Bluetooth turns on if it was on prior to suspend.
• Airplane Mode — When the ET1 is placed in Airplane Mode, the Bluetooth radio turns off. When Airplane
Mode is disabled, the Bluetooth radio returns to the prior state.
5.5 Bluetooth Radio Power
Turn off the Bluetooth radio to save power or if entering an area with radio restrictions (e.g., an airplane). When the radio is off, other Bluetooth devices cannot see or connect to the device. Turn on the Bluetooth radio to exchange information with other Bluetooth devices (within range). Communicate only with Bluetooth radios in close proximity.
MN000022A01 - May 2013 5-2
5.5.1 Enabling Bluetooth
To achieve the best battery life turn off radios not in use.
5.5.1 Enabling Bluetooth
Procedure Steps
1 Touch .
2 Slide the Bluetooth switch to the ON position. The Bluetooth icon also appears in the Status bar.
3 Touch .
5.5.2 Disabling Bluetooth
Procedure Steps
1 Touch .
2 Slide the Bluetooth switch to the OFF position.
3 Touch .
5.6 Discovering Bluetooth Devices
The ET1 can receive information from discovered devices without pairing. However, once paired, the ET1 and a paired device exchange information automatically when the Bluetooth radio is on. To find Bluetooth devices in the area:
Procedure Steps
1 Ensure that Bluetooth is enabled on both devices.
2 Ensure that the Bluetooth device to discover is in discoverable mode.
3 Ensure that the two devices are within 10 meters (32.8 ft.) of one another.
MN000022A01 - May 2013 5-3
ET1 Enterprise Tablet User Guide
4 Touch .
5 Touch Bluetooth .
6 Touch SCAN FOR DEVICES . The ET1 begins searching for discoverable Bluetooth devices in the area and displays them under AVAILABLE DEVICES .
7 Scroll through the list and select a device. The Bluetooth pairing request dialog box appears.
Figure 5-1 Bluetooth Pairing - Enter PIN
Figure 5-2 Bluetooth Pairing — Simple Pairing
5-4
8 Enter a PIN in the text box and touch OK .
9 Enter the same PIN on the other device. Touch Pair .
MN000022A01 - May 2013
5.7 Changing the Bluetooth Name
10 The Bluetooth device is added to the PAIRED DEVICES list and a trusted (“paired”) connection is established.
5.7 Changing the Bluetooth Name
By default, the ET1 has a generic Bluetooth name that is visible to other devices when connected.
To change the Bluetooth name:
Procedure Steps
1 Touch .
2 Touch Bluetooth .
3 If Bluetooth is not on, slide the switch to the ON position.
4 Touch .
5 Touch Rename device . The Rename device dialog box appears.
6 Enter a name and touch Done .
7 Touch .
5.8 Connecting to a Bluetooth Device
Once paired, connect to a Bluetooth device:
MN000022A01 - May 2013 5-5
ET1 Enterprise Tablet User Guide
Procedure Steps
1 Touch .
2 Touch Bluetooth .
3 If Bluetooth is not on, slide the switch to the ON position.
4 In the PAIRED DEVICES list, touch and hold on a unconnected Bluetooth device until a menu appears.
5 Touch Connect . When connected, the device is displayed as connected in the list.
5.9 Selecting Profiles on the Bluetooth Device
Some Bluetooth devices have multiple profiles. To select a profile:
Procedure Steps
1 Touch .
2 Touch Bluetooth .
3 If Bluetooth is not turned on, slide the blue switch to the On position.
4 In the PAIRED DEVICES list, touch next to the device name.
5 Under PROFILES , check or uncheck a profile to allow the ET1 to use that profile.
6 Touch .
5.10 Unpairing a Bluetooth Device
To unpair a Bluetooth device and erase all pairing information:
MN000022A01 - May 2013 5-6
5.10 Unpairing a Bluetooth Device
Procedure Steps
1 Touch .
2 Touch Bluetooth .
3 In the PAIRED DEVICES list, touch next to the device name.
4 Touch Unpair . The Bluetooth device is removed from the PAIRED DEVICE list.
5 Touch .
MN000022A01 - May 2013 5-7
6
Photos and Videos
This chapter provides information for taking photos and recording videos using the integrated digital cameras.
An installed microSD card is required to store photos and videos.
Photos and videos are stored on the micro secure digital (SD) card.
6.1 Taking Photos
Camera settings are described in
.
Procedure Steps
1 Touch .
MN000022A01 - May 2013 6-1
ET1 Enterprise Tablet User Guide
2 Touch .
Figure 6-1 Camera Mode
6-2
3 If necessary, touch the options bar and touch .
4 Touch to switch between the front or rear cameras.
5 Touch to adjust exposure, flash, and other settings using the camera settings. See
for more information.
6 Touch and to adjust the zoom level.
7 Frame the subject on screen.
MN000022A01 - May 2013
6.2 Taking a Panoramic Photo
8 Touch .
The camera brings the image into focus. When the image is in focus, the focus indicators in each corner turn green, the camera takes a photo and a shutter sound plays.
To disable the shutter sound, turn notification sounds off. Touch slide the Notifications slider all the way to the left.
> Sounds > Volumes and
Alternately, touch and hold to focus first, before taking a photo; then release to take a focused photo.
The photo appears momentarily then displays as a thumbnail in the upper right corner.
9 Touch the thumbnail to view the photo in Gallery . See
6.6 Viewing Photos and Videos, page 6-8
for more information.
6.2 Taking a Panoramic Photo
Panorama mode lets the user create a single wide image by panning slowly across a scene. To take a panoramic photo:
Procedure Steps
1 Touch .
2 Touch .
MN000022A01 - May 2013 6-3
ET1 Enterprise Tablet User Guide
3 Touch the options bar and touch
Figure 6-2 Panoramic Mode
.
4 Frame one side of the scene to capture.
5 Touch and slowly start panning across the area to capture. A small white square appears inside the button the shot is in progress.
If panning too quickly, the message Too fast appears.
6 Touch to end the shot. The panorama appears immediately and a progress indicator displays while it saves the image.
7 Touch the thumbnail to view the photo in Gallery . See
6.6 Viewing Photos and Videos, page 6-8 .
6.3 Recording Videos
Procedure Steps
1 Touch .
2 Touch .
6-4 MN000022A01 - May 2013
6.3 Recording Videos
3 Touch the options bar and touch
Figure 6-3 Video Mode
.
4 Touch to switch between the front or rear cameras.
5 Touch to adjust exposure, flash, and other settings using the video settings. See
for more information.
6 Touch and to adjust the zoom level.
7 Point the camera and frame the scene.
8 Touch to start recording.
The ET1 starts recording the video. The video time remaining appears in the top left of the screen.
9 Touch to end recording.
Previously recorded video displays in the thumbnail at the top right.
10 Touch the thumbnail to access the Gallery application. See
6.6 Viewing Photos and Videos, page 6-8
.
MN000022A01 - May 2013 6-5
ET1 Enterprise Tablet User Guide
6.4 Camera Settings
When in Camera mode, Camera settings are displayed on screen. Touch for the settings to change.
6.4.1 Rear-facing Camera Settings
Touch to display the camera setting options.
• Camera Settings - Touch to open a scrolling list of settings:
– Store location - Include location information with each photo using the ET1 global positioning system
(GPS). Options: On or Off (default).
– Focus Mode - Set the focus mode of the camera. Options: Macro , Infinity , Continuous , or Auto (default).
– Capture mode - Set the image capture mode. Options: High Quality (default) or Zero Shutter Mode .
– Picture size - Touch to set the size (in pixels) of the photo. Options: QVGA , VGA , 1M Pixels , 1.3M Pixels ,
2M pixels , 3M pixels , 5M pixels , or 8M pixels (default).
– ISO - Set how sensitive the camera is to light. Options: 800 , 400 , 200 , 100 , or Auto (default).
– Picture quality - Options: Super fine (default), Fine or Normal .
– Restore defaults - Touch Restore defaults to restore all camera settings to the default values.
• Scene mode - Touch to select a preset combination of camera settings designed for specific scenes.
Options: Auto (default), Portrait , Landscape , Night , Steady photo , or Sports .
• Exposure - Touch to adjust the exposure settings. Options: +3 , +2 , +1 , 0 (default), -1 , -2 , or -3 .
• White balance - Touch to select how Camera adjusts colors in different kinds of light, to achieve the most natural-looking colors.
–
–
–
–
–
Auto - Adjust the white balance automatically (default).
Incandescent - Adjust the white balance for incandescent lighting.
Daylight - Adjust the white balance for daylight.
Fluorescent - Adjust the white balance for florescent lighting.
Cloudy - Adjust the white balance for a cloudy environment.
• Flash mode - Touch to set whether Rear-facing Camera relies on its light meter to decide whether a flash is necessary, or to turn it on or off for all shots.
–
–
–
–
Auto - Camera adjusts flash automatically depending upon light meter.
On - Enable flash upon taking a photo.
Off - Disable flash (default).
Torch - Turn flash on continuously.
MN000022A01 - May 2013 6-6
6.4.2 Front-facing Camera Settings
6.4.2 Front-facing Camera Settings
Touch to display the camera setting options.
• Camera Settings - Touch to open a scrolling list of settings:
– Store location - Include location information with each photo using the ET1 global positioning system
(GPS). Options: On or Off (default).
– Picture size - Touch to set the size (in pixels) of the photo. Options: QVGA or VGA (default).
– Picture quality - Options: Super fine (default), Fine , Normal .
– Restore defaults - Touch Restore defaults to restore all camera settings to the default values.
• Scene mode - Touch to select a preset combination of camera settings designed for specific scenes.
Options: Auto (default) or Night .
6.5 Video Settings
When in Video mode, Video settings are displayed on the screen. Touch to change the video settings.
6.5.1 Video - Rear-facing Camera Settings
Touch to display the camera setting options.
–
–
–
–
• Settings - Touch to open a scrolling list of settings:
– Store location - Include location information with each photo using the ET1 global positioning system
(GPS). Options: On or Off (default).
– Restore defaults - Touch to restore all camera settings to the default values.
• Video quality - Touch to select video quality:
– HD - High definition 1080p.
– HD - High definition 720p.
– SD - Standard definition 480p (default).
• Time lapse interval — Touch to select a time interval to set the frame rate for time lapse photography. Options:
Off (default), 1s , 1.5s
, 2s , 2.5s
, 3s , 5s or 10s .
• White balance - Touch to select how the camera adjusts colors in different kinds of light, to achieve the most natural-looking colors for the video.
Auto - Adjust the white balance automatically (default).
Incandescent
Daylight
- Adjust the white balance for incandescent lighting.
- Adjust the white balance for daylight.
Fluorescent - Adjust the white balance for florescent lighting.
MN000022A01 - May 2013 6-7
ET1 Enterprise Tablet User Guide
•
– Cloudy - Adjust the white balance for a cloudy environment.
Flash mode - Select to illuminate the video by turning on the camera flash.
–
–
On - Enable flash.
Off - Disable flash (default).
6.5.2 Video - Front-facing Camera Settings
Touch to display the camera setting options.
• Camera Settings - Touch to open a scrolling list of settings:
– Restore defaults — Touch to restore all camera settings to the default values.
– Time lapse interval — Touch to select a time interval to set the frame rate for time lapse photography.
Options: Off (default), 1s , 1.5s
, 2s , 2.5s
, 3s , 5s or 10s .
6.6 Viewing Photos and Videos
6-8
The ET1 supports the following image formats: jpeg, gif, png and bmp.
The ET1 supports the following video formats: H.263, H.264 and MPEG4 Simple Profile.
Use Gallery to:
• view photos
• play videos
• perform basic editing of photos
• set photos as wallpaper
• set photos as a contact photo
• share photos and videos.
To open the Gallery application, touch the top right.
> or in the camera application touch the thumbnail image at
Gallery presents all photos and videos stored on the microSD card in albums.
MN000022A01 - May 2013
6.6.1 Working with Albums
Figure 6-4 Gallery — Albums
• Touch an album to open it and view its contents. The photos and videos in the album are displayed in chronological order.
• Touch a photo or video in an album to view it.
• Touch icon (top left corner) to return to the main Gallery screen.
6.6.1 Working with Albums
Albums are groups of images and videos in folders. Touch an album to open it. The photos and videos are listed in a chronologically ordered grid. The name of the album displays at the top of the screen.
MN000022A01 - May 2013 6-9
ET1 Enterprise Tablet User Guide
Figure 6-5 Photos Inside an Album
Swipe left or right to scroll images across the screen.
6-10 MN000022A01 - May 2013
6.6.1.1 Share an Album
6.6.1.1 Share an Album
Procedure Steps
1 Touch .
2 Touch .
3 Touch and hold an album until it highlights.
4 Touch other albums as required.
5 Touch . The Share menu opens. Touch the application to use to share the selected albums.
6 Follow the instructions within the selected application.
6.6.1.2 Get Album Information
Procedure Steps
1 Touch .
2 Touch .
3 Touch and hold an album until it highlights.
4 Touch > Details .
6.6.1.3 Deleting an Album
To delete an album and its contents from the microSD card:
MN000022A01 - May 2013 6-11
ET1 Enterprise Tablet User Guide
Procedure Steps
1 Touch .
2 Touch .
3 Touch and hold an album until it highlights.
4 Check other albums to delete. Ensure that other albums are selected.
5 Touch . The Delete selected item?
menu displays.
6 Touch OK to delete the album.
6.6.2 Working with Photos
Use Gallery to view photos on the microSD card and edit and share photos.
6.6.2.1 Viewing and Browsing Photos
Procedure Steps
1 Touch .
2 Touch .
3 Touch an album to open it.
6-12 MN000022A01 - May 2013
6.6.2.2 Rotating a Photo
4 Touch a photo.
Figure 6-6 Photo Example
5 Swipe left or right to view the next or previous photo in the album.
6 Turn the ET1 to view the photo in upright (portrait) or sideways (landscape) orientation. The photo is displayed
(but not saved) in the new orientation.
7 Touch the photo to view the controls.
8 Double-tap the screen to zoom in or pinch two fingers together or spread them apart to zoom in or out.
9 Drag the photo to view parts that are not in view.
6.6.2.2 Rotating a Photo
Procedure Steps
1 Touch a photo to view the controls.
2 Touch Rotate Left or Rotate Right . The photo is automatically saved with the new orientation.
6.6.2.3 Cropping a Photo
Procedure Steps
MN000022A01 - May 2013 6-13
ET1 Enterprise Tablet User Guide
1 Touch a photo to view the controls.
2 Touch Menu > Crop . The blue cropping tool appears.
3 Use the cropping tool to select the portion of the photo to crop.
• Drag from the inside of the cropping tool to move it.
• Drag an edge of the cropping tool to resize it to any proportion.
• Drag a corner of the cropping tool to resize it with fixed proportions.
Figure 6-7 Cropping Tool
4 Touch OK to save a copy of the cropped photo. The original version is retained.
6.6.2.4 Setting a Photo as a Contact Icon
Procedure Steps
1 Touch .
2 Touch .
3 Touch an album to open it.
6-14 MN000022A01 - May 2013
4 Touch the photo to open it.
5 Touch .
6 Touch Set picture as .
7 Touch Contact photo . The People app appears.
8 Touch a contact.
9 Touch the blue box and crop the photo accordingly.
10 Touch OK .
6.6.2.5 Get Photo Information
Procedure Steps
1 Touch .
2 Touch .
3 Touch an album to open it.
4 Touch the photo to open it.
5 Touch .
6 Touch Details .
6.6.2.6 Share a Photo
Procedure Steps
1 Touch .
2 Touch .
3 Touch an album to open it.
MN000022A01 - May 2013
6.6.2.5 Get Photo Information
6-15
ET1 Enterprise Tablet User Guide
4 Touch a photo to open it.
5 Touch . The Share menu appears.
6 Touch the application to use to share the selected photo. The application selected opens with the photo attached to a new message.
6.6.2.7 Deleting a Photo
Procedure Steps
1 Touch .
2 Touch .
3 Touch an album to open it.
4 Touch a photo to open it.
5 Touch .
6 Touch OK to delete the photo.
6.6.3 Working with Videos
Use Gallery to view videos on the microSD card and share videos.
6.6.3.1 Watching Videos
Procedure Steps
1 Touch .
2 Touch .
3 Touch an album to open it.
6-16 MN000022A01 - May 2013
6.6.3.2 Sharing a Video
4 Touch a video.
Figure 6-8 Video Example
5 Touch . The video begins to play.
6 Touch the screen to view the playback controls.
6.6.3.2 Sharing a Video
Procedure Steps
1 Touch .
2 Touch .
3 Touch an album to open it.
4 Touch a video to open it.
5 Touch . The Share menu appears.
6 Touch the application to use to share the selected video. The application selected opens with the video attached to a new message.
MN000022A01 - May 2013 6-17
ET1 Enterprise Tablet User Guide
6.6.3.3 Deleting a Video
Procedure Steps
1 Touch .
2 Touch .
3 Touch an album to open it.
4 Touch a video to open it.
5 Touch .
6 Touch OK .
6-18 MN000022A01 - May 2013
7
Accessories
This chapter provides information for using the accessories for the device.
7.1 ET1 Accessories
lists the accessories available for the ET1.
Table 7-1 ET1 Accessories
Accessory
Cradles
Single-slot USB
Docking Cradle
Four-slot
Charge Only
Docking Cradle
Chargers
Four-slot Spare
Battery Charger
Power Supply
Part Number
DC1000-1000U
DC1000-4000C
SAC1000-4000C
PWRS-14000-148C
Description
Charges the ET1 main battery and a spare battery. Synchronizes the ET1 with a host computer through a USB connection.
Charges up to four ET1 devices.
Charges up to four ET1 battery packs.
Power Supply PWRS-14000-241R
Provides power to the Single-slot USB Docking cradle or the
USB/Charge cable. 12 VDC, 4.16 A.
Provides power to the Four-slot Charge Only Docking cradle or the Four-slot Battery Charger. 12 VDC, 9 A.
Cables
USB Charge
Cable
DC Charge
Cable
2-way Charge
Cable
25-153149-01R
50-16002-029R
25-153150-01R
Provides power to the ET1 and USB communication with a host computer.
Connects one power supply to the one Four-slot Charge Only
Docking Cradle or the Four-slot Battery Charger.
Connects one power supply to one Four-slot Charge Only
Docking Cradle and one Four-slot Battery Charger or two
Four-slot Battery Chargers.
Provides power to the power supplies.
US AC Line
Cord (3-wire)
International
AC line Cord
Miscellaneous
Spare 4620 mAh lithium-ion battery
23844-00-00R
-
BTRY-ET01EAB0E
BTRY-ET01EAB0E-10
Provides power to the power supplies. Purchase separately.
Replacement 4620 mAh battery for ET1N0.
Replacement 4620 mAh battery for ET1N0 (10-pack)
MN000022A01 - May 2013 7-1
ET1 Enterprise Tablet User Guide
Table 7-1 ET1 Accessories (cont'd.)
Accessory
Spare 5640 mAh lithium-ion battery
Part Number
BTRY-ET01EAB0H
BTRY-ET01EAB0H-10
Handstrap SG-ET0123245-01R
Scanning
Module
Scanning/MSR
Module
Protective
Rubber Bezel
Mobile Payment
Module
SCANMOD-ET1
MSRSCAN-ET1
KT-161552-01R
MPM-100
Description
Replacement 5640 mAh battery for ET1N0 and ET1N2.
Replacement 5640 mAh battery for ET1N0 and ET1N2
(10-pack).
Adjustable and 360-degree rotatable handstrap that mounts on the back of the ET1 and provides a secure option for holding the device.
Provides 2D bar code scanning.
Provides 2D bar code scanning and magnetic stripe card reading.
Add additional protection for the ET1.
Adds mobile point of sale capable of Chip and PIN, and MSR transactions to the ET1.
7.2 Single-slot USB Docking Cradle
The Single-slot USB Docking cradle:
• Provides 12 VDC power for operating the ET1.
• Synchronizes information between the ET1 and a host computer. See the ET1 Enterprise Tablet Integrator Guide for information on setting up a connection to a host computer.
• Charges the battery.
Charging the ET1 Battery
Connect the cradle to power, then insert the ET1 into the slot to begin charging.
MN000022A01 - May 2013 7-2
Figure 7-1 ET1 in Single-slot USB Docking Cradle
7.3 Four-slot Charge Only Docking Cradle
The ET1 charge Battery Charge light emitting diode (LED) indicates the status of the battery charging in the
ET1. See
Table 1-2 Battery Charge LED Status
for charging status indications. The battery fully charges in approximately six hours.
Charge batteries in temperatures from 0 °C to 40 °C (32 °F to 104 °F). Charging is intelligently controlled by the
ET1. To accomplish this charging, for small periods of time, the ET1 or accessory alternately enables and disables the battery charging to keep the battery at acceptable temperatures. The ET1 indicates when charging is disabled due to abnormal temperatures via Battery Charge LED. See
Table 1-2 Battery Charge LED Status
.
Communication
When the ET1 is connected to a host computer using the Single-slot USB Docking cradle, the ET1 appears as a
Portable Device on the host computer. Refer to the ET1 Enterprise Tablet Integrator Guide for more information.
7.3 Four-slot Charge Only Docking Cradle
The Four-slot Charge Only Docking cradle:
• Provides 12 VDC power for operating the ET1.
• Simultaneously charges up to four ET1 devices.
Charging the ET1 Battery
Insert the ET1 into a slot to begin charging.
MN000022A01 - May 2013 7-3
ET1 Enterprise Tablet User Guide
Figure 7-2 ET1 Battery Charging
LEDs
The ET1’s Battery Charge LED shows the status of the battery charging in the ET1. See
for charging status indications. The battery fully charges in approximately six hours.
Charge batteries in temperatures from 0 °C to 40 °C (32 °F to 104 °F). Charging is intelligently controlled by the
ET1. To accomplish this, for small periods of time, the ET1 or accessory alternately enables and disables battery charging to keep the battery at acceptable temperatures. The ET1 indicates when charging is disabled due to abnormal temperatures via the Battery Charge LED. See
Table 1-2 Battery Charge LED Status .
7.4 Four-Slot Battery Charger
The Four-slot Battery Charger:
• Provides 12 VDC power for charging the batteries.
• Simultaneously charges up to four ET1 batteries.
Charging the Batteries
Insert the spare battery into a spare battery charging well.
7-4 MN000022A01 - May 2013
7.4 Four-Slot Battery Charger
A Charge LED is provided for each battery charging well. See
Table 7-2 Battery LED Charging Indicators
for charging status indications. The 4620 mAh battery fully charges in approximately six hours.
Figure 7-3 ET1 Battery Charging
Charge batteries in temperatures from 0 °C to 40 °C (32 °F to 104 °F). Charging is intelligently controlled by the charger in order to ensure safe operation and optimize long-term battery life. To accomplish this, for small periods of time, the charger alternately enables and disables battery charging to keep the battery at acceptable temperatures.
The charger indicates when charging is disabled due to abnormal temperatures via the Charge LED. See
Battery LED Charging Indicators .
Table 7-2 Battery LED Charging Indicators
LED
Off
Slow Blinking
Amber
Indication
No battery in slot.
Battery is not charging.
Battery is not inserted correctly in the charger.
Charger is not powered.
Battery is charging.
MN000022A01 - May 2013 7-5
ET1 Enterprise Tablet User Guide
Table 7-2 Battery LED Charging Indicators (cont'd.)
LED
Solid Green
Fast Blinking
Amber
Indication
Charging complete.
Charging error.
7.5 USB/Charge Cable
The USB/Charge cable:
• Provide the ET1 with operating and charging power.
• Synchronize information between the ET1 and a host computer.
Charging
Figure 7-4 Charging Using the USB/Charge Cable
The Battery Charge LED indicates the battery charging status. See
Table 1-2 Battery Charge LED Status
for charging status indications. The battery charges in approximately six hours.
Charge batteries in temperatures from 0 °C to 40 °C (32 °F to 104 °F). Charging is intelligently controlled by the
ET1. To accomplish this, for small periods of time, the ET1 alternately enables and disables battery charging to keep the battery at acceptable temperatures. The ET1 indicates when charging is disabled due to abnormal temperatures via the Battery Charge LED. See
Table 1-2 Battery Charge LED Status
.
Communication
Use the USB/Charge Cable to communicate with a host computer.
7-6 MN000022A01 - May 2013
Figure 7-5 Communication Using USB/Charge Cable
7.6 Using the Host USB Module
Connect the USB/Charge Cable cup to the bottom of the ET1. Align the ends of the cup with the alignment marks on the ET1.
When the ET1 is connected to a host computer using the USB/Charge cable, the ET1 appears as a Portable
Device on the host computer.
7.6 Using the Host USB Module
The USB Host Module provides USB Host connection to a peripheral.
MN000022A01 - May 2013 7-7
ET1 Enterprise Tablet User Guide
Procedure Steps
1 Lift the connector plug on the USB Host Module.
2 Connect the microUSB connector to the USB Host Module.
Figure 7-6 USB Host Module Connection
3 Connect the USB/Charge Cable cup to the bottom of the ET1. Align the ends of the cup with the alignment marks on the ET1.
When the ET1 is connected to a host computer using the USB/Charge cable, the ET1 appears as a Removable
Disk on the host computer.
7-8 MN000022A01 - May 2013
8
Maintenance and Troubleshooting
This chapter includes instructions on cleaning and storing the device, and provides troubleshooting solutions for potential problems during operation.
8.1 Maintaining the ET1
For trouble-free service, observe the following tips when using the ET1:
• Do not scratch the screen of the ET1. When working with the ET1, use a finger or approved stylus or pen intended for use with a capacitive touch-sensitive screen. Never use an actual pen or pencil or other sharp object on the surface of the ET1 screen.
• The touch-sensitive screen of the ET1 is glass. Do not to drop the ET1 or subject it to strong impact.
• Protect the ET1 from temperature extremes. Do not leave it on the dashboard of a car on a hot day, and keep it away from heat sources.
• Do not store or use the ET1 in any location that is dusty, damp, or wet.
• Use a soft lens cloth to clean the ET1. If the surface of the ET1 screen becomes soiled, clean it with a soft cloth moistened with a diluted window-cleaning solution.
• Periodically replace the rechargeable battery to ensure maximum battery life and product performance. Battery life depends on individual usage patterns.
8.2 Battery Safety Guidelines
• The area in which the units are charged should be clear of debris and combustible materials or chemicals.
Particular care should be taken where the device is charged in a non commercial environment.
• Follow battery usage, storage, and charging guidelines found in this guide.
• Improper battery use may result in a fire, explosion, or other hazard.
• To charge the mobile device battery, the battery and charger temperatures must be between +32 ºF and +104 ºF
(0 ºC and +40 ºC)
• Do not use incompatible batteries and chargers. Use of an incompatible battery or charger may present a risk of fire, explosion, leakage, or other hazard. If you have any questions about the compatibility of a battery or a charger, contact Motorola Solutions Global Customer Support Center.
• For devices that utilize a USB port as a charging source, the device shall only be connected to products that bear the USB-IF logo or have completed the USB-IF compliance program.
• To enable authentication of an approved battery, as required by IEEE1725 clause 10.2.1, all batteries will carry a
Motorola hologram. Do not fit any battery without checking it has the Motorola authentication hologram.
• Do not disassemble or open, crush, bend or deform, puncture, or shred.
• Severe impact from dropping any battery-operated device on a hard surface could cause the battery to overheat.
• Do not short circuit a battery or allow metallic or conductive objects to contact the battery terminals.
• Do not modify or remanufacture, attempt to insert foreign objects into the battery, immerse or expose to water or other liquids, or expose to fire, explosion, or other hazard.
MN000022A01 - May 2013 8-1
ET1 Enterprise Tablet User Guide
• Do not leave or store the equipment in or near areas that might get very hot, such as in a parked vehicle or near a radiator or other heat source. Do not place battery into a microwave oven or dryer.
• Battery usage by children should be supervised.
• Please follow local regulations to properly dispose of used re-chargeable batteries.
• Do not dispose of batteries in fire.
• In the event of a battery leak, do not allow the liquid to come in contact with the skin or eyes. If contact has been made, wash the affected area with large amounts of water and seek medical advice.
• If you suspect damage to your equipment or battery, contact Motorola Solutions Global Customer Support
Center to arrange for inspection.
8.3 Cleaning Instructions
Always wear eye protection.
Read warning label on compressed air and alcohol product before using.
If you have to use any other solution for medical reasons please contact Motorola for more information.
8-2
Avoid exposing this product to contact with hot oil or other flammable liquids. If such exposure occurs, unplug the device and clean the product immediately in accordance with these guidelines.
Approved Cleanser Active Ingredients
100% of the active ingredients in any cleaner must consist of one or some combination of the following: isopropyl alcohol, bleach/sodium hypochlorite, hydrogen peroxide or mild dish soap.
Harmful Ingredients
The following chemicals are known to damage the plastics on the device and should not come in contact with the device: ammonia solutions, compounds of amines or ammonia; acetone; ketones; ethers; aromatic and chlorinated hydrocarbons; acqueous or alcoholic alkaline solutions; ethanolamine; toluene; trichloroethylene; benzene; carbolic acid and TB-lysoform.
Cleaning Instructions
Do not apply liquid directly to the device. Dampen a soft cloth or use pre-moistened wipes. Do not wrap the device in the cloth or wipe, but gently wipe the unit. Be careful not to let liquid pool around the display window or other places. Allow the unit to air dry before use.
MN000022A01 - May 2013
8.3.1 Cleaning the ET1
Special Cleaning Notes
Many vinyl gloves contain phthalate additives, which are often not recommended for medical use and are known to be harmful to the housing of the device. The device should not be handled while wearing vinyl gloves containing phthalates, or before hands are washed to remove contaminant residue after gloves are removed. If products containing any of the harmful ingredients listed above are used prior to handling the device, such as hand sanitizer that contain ethanolamine, hands must be completely dry before handling the device to prevent damage to the plastics.
Cleaning Materials Required
• Alcohol wipes
• Lens tissue
• Cotton-tipped applicators
• Isopropyl alcohol
• Can of compressed air with a tube.
Cleaning Frequency
The cleaning frequency is up to the customer’s discretion due to the varied environments in which the mobile devices are used. They may be cleaned as frequently as required, but it is advisable to clean the camera window periodically when used in dirty environments to ensure optimum performance.
8.3.1 Cleaning the ET1
8.3.1.1 Housing
Using the alcohol wipes, wipe the housing including keys and in-between keys.
8.3.1.2 Display
The display can be wiped down with the alcohol wipes, but care should be taken not to allow any pooling of liquid around the edges of the display. Immediately dry the display with a soft, non-abrasive cloth to prevent streaking.
8.3.1.3 Camera Window
Wipe the camera window periodically with a lens tissue or other material suitable for cleaning optical material such as eyeglasses.
8.3.1.4 Connector Cleaning
To clean the connectors:
MN000022A01 - May 2013 8-3
ET1 Enterprise Tablet User Guide
Procedure Steps
1 Remove the main battery from mobile computer.
2 Dip the cotton portion of the cotton-tipped applicator in isopropyl alcohol.
3 Rub the cotton portion of the cotton-tipped applicator back-and-forth across the connector. Do not leave any cotton residue on the connector.
4 Repeat at least three times.
5 Use the cotton-tipped applicator dipped in alcohol to remove any grease and dirt near the connector area.
6 Use a dry cotton-tipped applicator and repeat steps 4 through 6.
Do not point nozzle at yourself and others, ensure the nozzle or tube is away from your face.
7 Spray compressed air on the connector area by pointing the tube/nozzle about ½ inch away from the surface.
8 Inspect the area for any grease or dirt, repeat if required.
8.3.2 Cleaning Cradle Connectors
To clean the connectors on a cradle:
8-4 MN000022A01 - May 2013
8.4 Troubleshooting
Procedure Steps
1 Remove the DC power cable from the cradle.
2 Dip the cotton portion of the cotton-tipped applicator in isopropyl alcohol.
3 Rub the cotton portion of the cotton-tipped applicator along the pins of the connector. Slowly move the applicator back-and-forth from one side of the connector to the other. Do not leave any cotton residue on the connector.
4 All sides of the connector should also be rubbed with the cotton-tipped applicator.
Do not point nozzle at yourself and others, ensure the nozzle or tube is pointed away from your face.
5 Spray compressed air in the connector area by pointing the tube/nozzle about ½ inch away from the surface.
6 Remove any lint left by the cotton-tipped applicator.
7 If grease and other dirt can be found on other areas of the cradle, use a lint-free cloth and alcohol to remove.
8 Allow at least 10 to 30 minutes (depending on ambient temperature and humidity) for the alcohol to air dry before applying power to cradle.
If the temperature is low and humidity is high, longer drying time is required. Warm temperature and dry humidity requires less drying time.
8.4 Troubleshooting
The following tables provides typical problems that might arise and the solution for correcting the problem.
MN000022A01 - May 2013 8-5
ET1 Enterprise Tablet User Guide
8.4.1 Troubleshooting the ET1 Enterprise Tablet
Table 8-1 Troubleshooting the ET1 Enterprise Tablet
Problem
When the user presses the Power button, the
ET1 does not turn on.
Cause
Battery is completely discharged.
Battery not installed properly.
Power button not held down long enough.
ET1 not responding.
Battery charge level is very low.
Solution
Re-charge or replace the battery.
Install the battery properly. See Installing the Battery on page 1-5.
Press the Power button until the Battery Charge LED flashes three times.
Perform a hard reset. See Resetting the ET1 on page 2-16.
Re-charge or replace the battery.
When the user presses the Power button the
ET1 does not turn on but the Decode LED blinks yellow.
Battery did not charge.
During data communication, no data transmitted, or transmitted data was incomplete.
No sound.
ET1 turns off.
Battery failed.
ET1 was removed from cradle while battery was charging.
Extreme battery temperature.
ET1 removed from cradle or disconnected from host computer during communication.
Incorrect cable configuration.
Replace battery. If the ET1 still does not operate, perform a hardware reset. Simultaneously press the Power, Left Scan/Action and Right Scan/Action buttons.
Insert ET1 in cradle. The 4620 mAh battery fully charges in less than six hours.
Battery does not charge if ambient temperature is below 0°C (32°F) or above 40°C (104°F).
Replace the ET1 in the cradle, or reattach the communication cable and re-transmit.
See the system administrator.
Volume setting is low or turned off.
Adjust the volume.
ET1 is inactive.
The display turns off after a period of inactivity. Set this period to
15 seconds, 30 seconds, 1, 2, 10, or 30 minutes.
Battery is depleted.
Recharge or replace the battery.
MN000022A01 - May 2013 8-6
8.4.1 Troubleshooting the ET1 Enterprise Tablet
Table 8-1 Troubleshooting the ET1 Enterprise Tablet (cont'd.)
Problem
A message appears stating not enough storage memory.
The ET1 does not decode when reading bar code.
ET1 does not read magnetic stripe card
ET1 cannot find any
Bluetooth devices nearby.
Cause
Too many applications installed on the
ET1.
DataWedge is not enabled.
Unreadable bar code.
Distance between the ET1 and bar code is incorrect.
ET1 is not programmed for the bar code type.
ET1 is not programmed to generate a beep.
Magnetic stripe on card is facing the wrong way.
MSR reading is not enabled.
Too far from other Bluetooth devices.
The Bluetooth device(s) nearby are not turned on.
The Bluetooth device(s) are not in discoverable mode.
Solution
Remove user-installed applications on the ET1 to recover memory.
Select and touch
> Apps
Uninstall .
> Downloaded . Select the unused programs
Ensure that DataWedge is enabled and configured properly. Refer to the ET1 Enterprise Tablet Integrator Guide for more information.
Ensure the symbol is not defaced.
Place the ET1 within proper scanning range.
Program the ET1 to accept the type of bar code being scanned.
Refer to the ET1 Enterprise Tablet Integrator Guide for DataWedge configuration.
If the ET1 does not beep on a good decode, set the application to generate a beep on good decode.
Ensure that magnetic stripe card is oriented correctly. Magnetic stripe of card should be facing the display.
Program the ET1 to accept MSR input. Refer to the ET1 Enterprise
Tablet Integrator Guide for DataWedge configuration.
Move closer to the other Bluetooth device(s), within a range of 10 meters (30 feet).
Turn on the Bluetooth device(s) to find.
Set the Bluetooth device(s) to discoverable mode. If needed, refer to the device’s user documentation for help.
MN000022A01 - May 2013 8-7
ET1 Enterprise Tablet User Guide
8.4.2 Single-slot USB Docking Cradle Troubleshooting
Table 8-2 Troubleshooting the Single-slot USB Docking Cradle
Problem
ET1 battery is not charging.
During data communication, no data transmits, or transmitted data was incomplete.
Cause
ET1 was removed from cradle or cradle was unplugged from AC power too soon.
Battery is faulty.
Verify that other batteries charge properly. If so, replace the faulty battery.
The ET1 is not fully seated in the cradle.
Extreme battery temperature.
ET1 removed from cradle during communications.
Communication software is not installed or configured properly.
Solution
Ensure cradle is receiving power. Ensure ET1 is seated correctly.
Confirm the battery is charging. The battery fully charges in less than six hours.
Remove and re-insert the ET1 into the cradle, ensuring it is firmly seated.
Battery does not charge if ambient temperature is below 0 °C (32
°F) or above 40 °C (104 °F).
Replace ET1 in cradle and retransmit.
Perform setup as described in the
Guide .
ET1 Enterprise Tablet Integrator
8-8 MN000022A01 - May 2013
8.4.3 Four-slot Charge Only Docking Cradle Troubleshooting
8.4.3 Four-slot Charge Only Docking Cradle
Troubleshooting
Table 8-3 Troubleshooting the Four-slot Charge Only Docking Cradle
Problem
Battery is not charging.
Cause
ET1 removed from the cradle too soon.
Battery is faulty.
Verify that other batteries charge properly. If so, replace the faulty battery.
ET1 is not inserted correctly in the cradle.
Solution
Replace the ET1 in the cradle. The battery fully charges in less than six hours. Touch battery status.
Remove the ET1 and reinsert it correctly. Verify charging is active.
Touch >
>
About device >
About device
Status
> Status to view to view battery status.
Ambient temperature of the cradle is too warm.
Move the cradle to an area where the ambient temperature is between 0 °C (32 °F) and 35 °C (95 °F).
8.4.4 Four-slot Battery Charger Troubleshooting
Table 8-4 Troubleshooting the Four-slot Battery Charger
Problem
Battery not charging.
Cause
Battery was removed from the charger or charger was unplugged from
AC power too soon.
Solution
Re-insert the battery in the charger or re-connect the charger’s power supply. The battery fully charges in less than six hours.
Battery is faulty.
Verify that other batteries charge properly. If so, replace the faulty battery.
Battery contacts not connected to charger.
Verify that the battery is seated in the battery well correctly with the contacts facing down.
MN000022A01 - May 2013 8-9
ET1 Enterprise Tablet User Guide
8.4.5 USB/Charge Cable Troubleshooting
Table 8-5 Troubleshooting the USB/Charge Cable
Problem
Battery not charging.
During data communication, no data transmits, or transmitted data was incomplete.
Cause Solution
ET1 was disconnected from AC power too soon.
Connect the power cable correctly. Confirm main battery is charging under > About device in less than six hours.
> Status . The battery fully charges
Battery is faulty.
Verify that other batteries charge properly. If so, replace the faulty battery.
The ET1 is not connected to power.
Detach and re-attach the power cable to the ET1, ensuring it is firmly connected.
Cable was disconnected from
ET1 during communications.
Re-attach the cable and retransmit.
Incorrect cable configuration.
Communication software is not installed or configured properly.
See the system administrator.
Perform setup as described in the
Guide .
ET1 Enterprise Tablet Integrator
8-10 MN000022A01 - May 2013
Appendix A: Technical Specifications
The following sections provide technical specification for the device.
A.1 ET1 Technical Specifications
The following table summarize the ET1’s intended operating environment and technical hardware specifications.
Table A-1 ET1 Technical Specifications
Item
Physical Characteristics
Dimensions (with USB Host
Expansion Module)
Description
Height: 130.5 mm (5.14 in.)
Width: 224 mm (8.82 in.)
Weight
Depth: 25 mm (0.98 in.)
ET1N0: 630 g (22.4 oz.)
Display
Touch Panel
Backlight
Battery Pack
Backup Battery
ET1N2: 706 g (24.9 oz.)
7 in. capacitive; 1024 x 600; 350 nit; Corning® Gorilla® Glass.
Capacitive multi-touch
LED backlight
Rechargeable Lithium Ion 3.7V, 4620 mAh or 5640 mAh Smart battery.
NiMH battery (rechargeable) 15 mAh 3.6 V (not user accessible).
Expansion Slot
Connectivity
Notification
Keypad Options
Audio
User accessible microSD slot, up to 32 GB.
Two USB interfaces: one USB 2.0 OTG connector (docking connector) and one
USB 2.0 Host connector (expansion module port); HDMI output; communication via cradle and expansion ports; USB 2.0 host via expansion module.
LED, audio and vibration.
On-screen keyboard.
Stereo speakers, microphone and headset connector (mono, 2.5 mm jack with microphone.)
Performance Characteristics
CPU Texas Instruments OMAP 4430 @ 1 GHz.
Operating System
Memory
Android-based ASOP 4.1.1.
1GB RAM, 4 GB Flash plus 4 GB microSD; user accessible microsD card slot
(supports up to 32 GB).
Output Power (USB) Docking Connector: 5 VDC @ 500 mA max.
Expansion Module: 5 VDC @ 500 mA max.
User Environment
MN000022A01 - May 2013 A-1
ET1 Enterprise Tablet User Guide
Table A-1 ET1 Technical Specifications (cont'd.)
Item
Operating Temperature
Storage Temperature
Description
0°C to 50°C (32°F to 122°F)
-40°C to 70°C (-40°F to 158°F)
Charging Temperature
Humidity
0° C to 40° C (32°F to 104°F)
10% to 95% RH non-condensing
Drop Specification Multiple 1.2 m (4 ft.) drops per MIL-STD 810G specifications.
Electrostatic Discharge (ESD) +/-15kVdc air discharge, +/-8kVdc direct discharge, +/-8kVdc indirect discharge
Sealing IP54
Wireless LAN Data Communications
IEEE ® 802.11a/b/g/n with internal antenna Wireless Local Area Network
(WLAN) radio
Data Rates Supported
Operating Channels
Security
1, 2, 5.5, 6, 9, 11, 12, 18, 24, 36, 48, and 54 Mbps. Note that 802.11n data rates may be higher.
Chan 36-165 (5180 – 5825 MHz), Chan 1-13 (2412-2472 MHz); actual operating channels/frequencies depend on regulatory rules and certification agency
Security Modes: Legacy, WPA and WPA2
Encryption: WEP (40 and 128 bit), TKIP and AES
Spreading Technique
Authentication: TLS, TTLS (MS-CHAP), TTLS (MS-CHAP v2), TTLS
(CHAP), TTLS (PAP), PEAP-TLS, PEAP (MS-CHAP v2), EAP -FAST-TLS,
EAP-FAST (MS-CHAP v2).
Direct Sequence Spread Spectrum (DSSS) and Orthogonal Frequency Division
Multiplexing (OFDM)
Wireless PAN Data and Voice Communications
Bluetooth Class II, v 2.1 with EDR; integrated antenna.
Wireless WAN Data (ET1N2 only)
Wireless Wide Area Network Data only: 3.5G GSM HSDPA and 3.5G CDMA-EVDO Rev A.
Data Capture
Rear-facing Camera For bar code scanning and image capture: 8 MP auto-focus camera with user controllable LED flash, illumination and aiming; captures 1D and 2D bar codes, photographs, video, signatures and documents.
Front-facing Camera
Scanning Module
Scanning/MSR Module
Sensors
Gyroscope
Motion Sensor
Ambient Light Sensor
VGA camera optimized for video collaboration and low lighting condition.
For bar code scanning.
For bar code scanning and reading magnetic stripe cards.
Maintains orientation based on principles of conservation of angular momentum.
3-axis accelerometer that enables motion sensing applications for dynamic screen orientation and power management.
Automatically adjusts display brightness.
A-2 MN000022A01 - May 2013
A.2 Single-slot USB Docking Cradle Technical Specifications
Table A-1 ET1 Technical Specifications (cont'd.)
Item
Electronic Compass
Description
Independent — does not depend on GPS.
Scanning / Scanning/MSR Module (SE4500-DL) Specifications
Field of View Horizontal - 39.2°
Optical Resolution
Roll
Pitch Angle
Skew Tolerance
Vertical - 25.4°
WVGA 752 H x 480 V pixels (gray scale)
360°
+/- 60° from normal
+/- 60° from normal
Ambient Light
Focal Distance
Outdoor: 9000 ft. candles (96,900 lux)
From center of exit window: 18.5 cm (7.3 in.)
Aiming Element (VLD) 655 nm +/- 10 nm
Illumination Element (LED) 625 nm +/- 5 nm
Supported Symbologies
1D
2D
Chinese 2 of 5, Codabar, Code 11, Code 128, Code 39, Code 93, Discrete 2 of 5,
EAN-8, EAN-13, GS1 DataBar, GS1 DataBar Expanded, GS1 DataBar Limited,
Interleaved 2 of 5, Korean 2 of 5, MSI, TLC 39, Matrix 2 of 5, Trioptic, UPCA,
UPCE, UPCE1, Web Code.
Australian Postal, Aztec, Canadian Postal, Composite AB, Composite C, Data
Matrix, Dutch Postal, Japan Postal, Maxicode, Micro PDF, Micro QR, PDF, QR
Code, UK Postal, US Planet, US Postnet, US4State, US4State FICS
A.2 Single-slot USB Docking Cradle Technical
Specifications
The following table summarize the ET1’s intended operating environment and technical hardware specifications.
Table A-2 Single-slot USB Docking Cradle Technical Specifications
Item
Dimensions (with USB Host
Expansion Module)
Weight
Input Voltage
Power Consumption (with
ET1)
Description
Height: 61.62 mm (2.43 in.)
Width: 151.9 mm (5.98 in.)
Depth: 138.39 mm (5.45 in.)
620 g (21.87 oz)
12 VDC
24 watts
MN000022A01 - May 2013 A-3
ET1 Enterprise Tablet User Guide
Table A-2 Single-slot USB Docking Cradle Technical Specifications (cont'd.)
Item
Interface
Operating Temperature
Storage Temperature
Description
USB
0°C to 50°C (32°F to 122°F)
-40°C to 70°C (-40°F to 158°F)
Charging Temperature
Humidity
0°C to 40°C (32°F to 104°F)
5% to 95% non-condensing
Drop 76.2 cm (30.0 in.) drops to vinyl tiled concrete at room temperature
Electrostatic Discharge (ESD) +/- 15 kV air
+/- 8 kV contact
A.3 Four-slot Charge Only Cradle Technical
Specifications
Table A-3 Four-slot Charge Only Cradle Technical Specifications
Item
Dimensions (with USB Host
Expansion Module)
Description
Height: 83.45 mm (3.29 in.)
Width: 243.28 mm (9.58 in.)
Weight
Input Voltage
Power Consumption (with
ET1)
Operating Temperature
Storage Temperature
Charging Temperature
Depth: 330.17 mm (13.00 in.)
1.678 kg (3.70 lbs.)
12 VDC
50 watts
0 °C to 50 °C (32 °F to 122 °F)
-40 °C to 70 °C (-40 °F to 158 °F)
0 °C to 40 °C (32 °F to 104 °F)
Humidity
Drop
5% to 95% non-condensing
76.2 cm (30.0 in.) drops to vinyl tiled concrete at room temperature
Electrostatic Discharge (ESD) +/- 15 kV air
+/- 8 kV contact
MN000022A01 - May 2013 A-4
A.4 Four-slot Battery Charger Technical Specifications
A.4 Four-slot Battery Charger Technical
Specifications
Table A-4 Four-slot Battery Charger Technical Specifications
Item
Dimensions (with USB Host
Expansion Module)
Description
Height: 110.62 mm (4.36 in.)
Width: 100.88 mm (3.97 in.)
Weight
Input Voltage
Power Consumption (with
ET1)
Operating Temperature
Storage Temperature
Depth: 245.15 mm (9.65)
580 g (20.46 in.)
12 VDC
25 watts
0 °C to 40 °C (32 °F to 104 °F)
-40 °C to 70 °C (-40 °F to 158 °F)
Charging Temperature
Humidity
0 °C to 40 °C (32 °F to 104 °F)
5% to 95% non-condensing
Drop 76.2 cm (30.0 in.) drops to vinyl tiled concrete at room temperature
Electrostatic Discharge (ESD) +/- 15 kV air
+/- 8 kV contact
A.5 USB/Charge Cable Technical Specifications
Table A-5 USB/Charge Cable Technical Specifications
Item Description
Length
Operating Temperature
160.0 cm (63.0 in.)
0 °C to 40 °C (32 °F to 104 °F)
Storage Temperature
Humidity
-40 °C to 70 °C (-40 °F to 158 °F)
10% to 95% non-condensing
Electrostatic Discharge (ESD) +/- 15 kV air
+/- 8 kV contact
MN000022A01 - May 2013 A-5
Index
2–way charge cable ................................................. 7-1
A
action button .......................................................... 1-3
CDMA .............................................................. 1-8
GSM ................................................................. 1-8
WAN................................................................. 1-8
adaptive frequency hopping ...................................... 5-1
airplane mode......................................................... 5-2
albums .................................................................. 6-9
application shortcuts ................................................ 2-6
applications .......................................................... 2-13
applock administrator ............................................. 2-15
approved cleanser ................................................... 8-2
camera settings ....................................................... 6-6
CDMA activation.................................................... 1-8
charging four-slot charge only cradle ................................... 7-3
clock ................................................................... 2-13
communication....................................................... 7-6
communication LED ............................................... 1-2
configuration.......................................................... xiii
contacts................................................................ 2-14
cradle connector cleaning ............................................... 8-4
creating folders....................................................... 2-8
CS3070..................................................... xiii, 3-1–3-2
B
charging............................................................. 1-6
charging temperature ............................................ 1-8
low battery notification ........................................ 1-14
management ...................................................... 1-13
replacement ........................................................ 1-9
battery charge LED ................................................. 1-2
battery installation................................................... 1-5
bezel .................................................................... 7-2
bluetooth ............................................................... 5-1
bluetooth power states.............................................. 5-2
browser................................................................ 2-13
C
camera .....................................................xiii, 2-13, 3-1
front-facing ........................................................ 1-2
camera scanning ..................................................... 3-4
D
data capture ........................................................... 3-1
data capture options................................................. xiii
datawedge ................................................2-13, 3-1, 3-7
date ..................................................................... 1-17
DC charge cable ..................................................... 7-1
decode mode .......................................................... 3-1
default notifications ................................................ 1-22
deleting a message ................................................. 2-25
dial-up networking profile......................................... 5-2
digital camera......................................................... 3-2
display .................................................................. xiii
cleaning ............................................................. 8-3
downloads ............................................................ 2-14
DWdemo...................................................... 2-14–2-15
E
email ................................................................... 2-14
entering text.......................................................... 2-12
F
file browser................................................... 2-14, 2-21
font ..................................................................... 1-20
forwarding a message ............................................. 2-24
four-slot battery charger ........................................... 7-4
four-slot charge only cradle....................................... 7-1
four-slot charge only docking cradle ........................... 7-3
four-slot spare battery charger ................................... 7-1
G
gallery ................................................................. 2-14
MN000022A01 - May 2013 I
Index
I
generic access profile ............................................... 5-2
getting started......................................................... 1-1
GSM activation ...................................................... 1-8
H
handstrap........................................................ 1-12, 7-2
hard reset ............................................................. 2-20
harmful ingredients ................................................. 8-2
headset jack ........................................................... 1-3
home button........................................................... 1-2
home screen........................................................... 2-1
Host USB module ................................................... 7-7
human interface device profile ................................... 5-2
I/O connector ......................................................... 1-3
K
keyboard .............................................................. 2-11
P
panoramic ............................................................. 6-3
password .............................................................. 2-17
photos................................................................... 6-1
picklist mode ......................................................... 3-1
PIN ..................................................................... 2-17
power button .................................................... 1-3, 1-8
protective rubber bezel............................................. 7-2
R
radios ................................................................... xiii
rapid deployment ................................................... 2-15
recent applications ................................................. 2-16
recording videos ..................................................... 6-4
removing a folder.................................................... 2-9
replacing the battery ................................................ 1-9
replacing the microSD card...................................... 1-10
resetting ............................................................... 2-20
responding to a message .......................................... 2-23
resume .................................................................. 5-2
rotate screen.......................................................... 1-19
L
laser scanning......................................................... 3-2
light sensor ............................................................ 1-2
M
main battery charging .............................................. 1-7
memory ................................................................ xiii
menu button........................................................... 1-2
messaging .................................................... 2-14, 2-23
microphone............................................................ 1-2
microSD card replacement ....................................................... 1-10
MSP agent............................................................ 2-14
multiuser administrator ........................................... 2-15
music................................................................... 2-14
N
naming folders ....................................................... 2-8
notification icons .................................................... 2-2
notification panel .................................................... 2-5
O
operating system ..................................................... xiii
S
scan angle.............................................................. 3-2
scan button ............................................................ 1-3
scanning................................................................ 3-3
scanning module ......................................... xiii, 3-1, 7-2
scanning range ....................................................... 3-2
scanning/MSR module ....................................... xiii, 3-1
screen brightness ................................................... 1-16
screen lock sounds ................................................. 1-22
screen rotation....................................................... 1-19
screen timeout ............................................... 1-15, 1-20
sending a text message ............................................ 2-23
serial port profile..................................................... 5-2
service ....................................................................xv
service discovery protocol ........................................ 5-2
setting camera............................................................... 6-6
setting font size ..................................................... 1-20
settings ................................................................ 2-15
setup .................................................................... 1-4
side LED ............................................................... 1-3
SIM card ............................................................... 1-4
SIM card installation ............................................... 1-4
single user mode .................................................... 2-16
single-slot USB docking cradle.................................. 7-1
soft reset .............................................................. 2-20
spare battery .......................................................... 7-1
spare battery charging .............................................. 1-8
speakers ................................................................ 1-3
II MN000022A01 - May 2013
Index
suspend................................................................. 5-2
system sounds ....................................................... 1-22
T
taking a panoramic photo.......................................... 6-3
taking photos ......................................................... 6-2
text message limit .................................................. 2-25
time..................................................................... 1-17
touch screen........................................................... 1-3
turning off radios ................................................... 1-17
U
unpacking.............................................................. 1-4
USB charge cable ................................................... 7-1
USB communication ............................................... 7-6
USB host mode ...................................................... 7-7
USB/charge cable ................................................... 7-6
user guide............................................................. 2-14
V
vibrate on touch ..................................................... 1-22
videos............................................................. 6-1, 6-4
volume ................................................................ 1-21
W
WAN activation ...................................................... 1-8
WLAN.................................................................. 4-1
MN000022A01 - May 2013 III
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 26 Getting Started
- 26 Features
- 26 Unpacking
- 26 Setup
- 26 Installing the SIM Card
- 26 Installing the Battery
- 26 Charging the Battery
- 26 1.3.3.1 Charging the Main Battery
- 26 1.3.3.2 Charging Temperature
- 26 1.3.3.3 Charging Spare Batteries
- 26 Powering On the ET
- 26 WAN Activation
- 26 1.3.5.1 GSM Activation
- 26 1.3.5.2 CDMA Activation
- 26 Replacing the Battery
- 26 Replacing the microSD Card
- 26 Handstrap
- 26 Battery Management
- 26 Monitor Battery Usage
- 26 Low Battery Notification
- 26 Battery Optimization
- 26 1.7.3.1 Changing the Screen Timeout Setting
- 26 1.7.3.2 Changing the Brightness Setting
- 26 1.7.3.3 Turning Off the Radios
- 26 Setting the Date and Time
- 26 Display Setting
- 26 Setting the Screen Brightness
- 26 Setting Screen Rotation
- 26 Setting Screen Sleep
- 26 Setting Font Size
- 26 General Sounds Setting
- 27 Using the ET
- 27 Home Screen
- 27 Status Bar
- 27 Status Icons
- 27 Notification Icons
- 27 Managing Notifications
- 27 Application Shortcuts and Widgets
- 27 Adding an Application or Widget to the Home Screen
- 27 Moving Items on the Home Screen
- 27 Removing an App or Widget from the Home Screen
- 27 Folders
- 27 Creating Folders
- 27 Naming Folders
- 27 Removing a Folder From the Home Screen
- 27 Home Screen Wallpaper
- 27 Change the Home Screen Wallpaper
- 27 Moving Items on the Home Screen
- 27 Removing Items from the Home Screen
- 27 Using the Touchscreen
- 27 Using the On-screen Keyboard
- 27 Entering Text
- 63 Applications
- 63 Switching Between Recent Applications
- 63 Un-Locking the Screen
- 63 Single User Mode
- 63 MultiUser Mode
- 63 2.11.2.1 Multiuser Login
- 63 2.11.2.2 Multiuser Logout
- 63 Resetting the Device
- 63 Performing a Soft Reset
- 63 Performing a Hard Reset
- 63 Wake-up Settings
- 63 Waking the ET
- 63 File Browser
- 63 Messaging
- 63 Opening Messaging
- 63 Sending a Text Message
- 63 Responding to a Message
- 63 Forwarding a Message
- 63 Locking a Message
- 63 Viewing Message Details
- 63 Deleting a Message Thread
- 63 Messaging Settings
- 64 Data Capture
- 64 Scanning Modules
- 64 Operational Modes
- 64 Digital Camera
- 64 Laser Scanning
- 64 Scanning Considerations
- 64 Bar Code Capture with Scanning or Scanning/MSR Module
- 64 Bar Code Capture with Integrated Camera
- 64 Bar Code Capture with CS3070 Bluetooth Scanner
- 64 Reading Magnetic Stripe Cards with Scanning/MSR Module
- 64 DataWedge
- 64 Enabling DataWedge
- 64 Disabling DataWedge
- 64 DataWedge Configuration
- 65 Connecting to a Wi-Fi Network
- 66 Bluetooth
- 66 Adaptive Frequency Hopping
- 66 Security
- 66 Bluetooth Profiles
- 66 Bluetooth Power States
- 66 Bluetooth Radio Power
- 66 Enabling Bluetooth
- 66 Disabling Bluetooth
- 66 Discovering Bluetooth Devices
- 66 Changing the Bluetooth Name
- 66 Connecting to a Bluetooth Device
- 66 Selecting Profiles on the Bluetooth Device
- 66 Unpairing a Bluetooth Device
- 67 Photos and Videos
- 67 Taking Photos
- 67 Taking a Panoramic Photo
- 67 Recording Videos
- 113 Camera Settings
- 113 Rear-facing Camera Settings
- 113 Front-facing Camera Settings
- 113 Video Settings
- 113 Video - Rear-facing Camera Settings
- 113 Video - Front-facing Camera Settings
- 113 Viewing Photos and Videos
- 113 Working with Albums
- 113 6.6.1.1 Share an Album
- 113 6.6.1.2 Get Album Information
- 113 6.6.1.3 Deleting an Album
- 113 Working with Photos
- 113 6.6.2.1 Viewing and Browsing Photos
- 113 6.6.2.2 Rotating a Photo
- 113 6.6.2.3 Cropping a Photo
- 113 6.6.2.4 Setting a Photo as a Contact Icon
- 113 6.6.2.5 Get Photo Information
- 113 6.6.2.6 Share a Photo
- 113 6.6.2.7 Deleting a Photo
- 113 Working with Videos
- 113 6.6.3.1 Watching Videos
- 113 6.6.3.2 Sharing a Video
- 113 6.6.3.3 Deleting a Video
- 114 Accessories
- 114 ET1 Accessories
- 114 Single-slot USB Docking Cradle
- 114 Four-slot Charge Only Docking Cradle
- 114 Four-Slot Battery Charger
- 114 USB/Charge Cable
- 114 Using the Host USB Module
- 115 Maintenance and Troubleshooting
- 115 Maintaining the ET
- 115 Battery Safety Guidelines
- 115 Cleaning Instructions
- 115 Cleaning the ET
- 115 8.3.1.1 Housing
- 115 8.3.1.2 Display
- 115 8.3.1.3 Camera Window
- 115 8.3.1.4 Connector Cleaning
- 115 Cleaning Cradle Connectors
- 115 Troubleshooting
- 115 Troubleshooting the ET1 Enterprise Tablet
- 115 Single-slot USB Docking Cradle Troubleshooting
- 115 Four-slot Charge Only Docking Cradle Troubleshooting
- 115 Four-slot Battery Charger Troubleshooting
- 115 USB/Charge Cable Troubleshooting
- 130 Features
- 130 Battery Charge LED Status
- 131 Home Screen Items
- 131 Status Icons
- 131 Notification Icons
- 131 ET1 Default Applications
- 131 Wake-up Default Settings