OPERATOR’S MANUAL

INCLUDING: OPERATION, INSTALLATION & MAINTENANCE

PD07P-X-X

RELEASED:

REVISED:

(REV. 04)

2-16-07

5-21-10

3/4" DIAPHRAGM PUMP

1:1 RATIO (NON-METALLIC)

READ THIS MANUAL CAREFULLY BEFORE INSTALLING,

OPERATING OR SERVICING THIS EQUIPMENT.

It is the responsibility of the employer to place this information in the hands of the operator. Keep for future reference.

SERVICE KITS

Refer to Model Description Chart to match the pump material options.

637427-XX for fl uid section repair (see page 4).

637428 for air section repair (see page 6).

PUMP DATA

Models . . . . . . . . . . . . . see Model Description Chart for “-XXX”

Pump Type . . . . . . . . . Air Operated Double Diaphragm

Material . . . . . . . . . . . . see Model Description Chart

Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.61 lbs (2.54 kgs)

Maximum Air Inlet Pressure . . . . . . . . 100 p.s.i.g. (6.9 bar)

Maximum Material Inlet Pressure . . . 10 p.s.i.g. (0.69 bar)

Maximum Outlet Pressure . . . . . . . . . . 100 p.s.i.g. (6.9 bar)

Air Consumption @ 40 p.s.i. . . . . . . . 1 c.f.m. / gallon (approx.)

Maximum Flow Rate (fl ooded inlet) . . . 14.8 g.p.m. (56.0 l.p.m.)

Displacement / Cycle @ 100 p.s.i.g.

. 0.032 gal. (0.12 lit.)

Maximum Particle Size . . . . . . . . . . . . . 3/32” dia. (2.4 mm)

Maximum Temperature Limits (diaphragm / ball / seat material)

Hytrel® . . . . . . . . . . . . . . . . . . . -20° to 150° F (-29° to 66° C)

Polypropylene . . . . . . . . . . . . 35° to 175° F (2° to 79° C)

Santoprene® . . . . . . . . . . . . . . -40° to 225° F (-40° to 107° C)

PTFE . . . . . . . . . . . . . . . . . . . . . . 40° to 225° F (4° to 107° C)

Dimensional Data . . . . . . . . . . . . . . . . . . . see page 8

Noise Level @ 70 p.s.i., 60 c.p.m. . . . . . . 75.0 db(A) c c The pump sound pressure levels published here have been updated to an Equivalent Continuous Sound Level (L

Aeq

) to meet the intent of ANSI

S1.13-1971, CAGI-PNEUROP S5.1 using four microphone locations.

NOTICE: All possible options are shown in the chart, however, certain combinations may not be recommended, consult a representative or the factory if you have questions concerning availability.

MODEL DESCRIPTION CHART

PD07P - X P S - P X X

Center Section Material

P - Polypropylene

Fluid Connection

A - 3/4 - 14 N.P.T.F. - 1

B - Rp 3/4 (3/4 - 14 BSP, parallel)

Fluid Cap & Manifold Material

P - Polypropylene

Hardware Material

S - Stainless Steel

Seat Material

P - Polypropylene

Ball Material

A - Santoprene

C - Hytrel

T - PTFE

Diaphragm Material

A - Santoprene

C - Hytrel

T - PTFE / Santoprene

Fluid Section Service Kit Selection

EXAMPLE: Model #PD07P-APS-PAA

Fluid Section Service Kit # 637427-AA

Figure 1

PD07P - XPS - P X X

637427 - X X

Ball Diaphragm

INGERSOLL RAND COMPANY LTD

209 NORTH MAIN STREET -- BRYAN, OHIO 43506

(800) 495-0276 y FAX (800) 892-6276

© 2010 CCN 15275175

OPERATING AND SAFETY PRECAUTIONS

y y y y y y y y y y y y y y y y

READ, UNDERSTAND AND FOLLOW THIS INFORMATION TO AVOID INJURY AND PROPERTY DAMAGE.

EXCESSIVE AIR PRESSURE

STATIC SPARK

WARNING

HAZARDOUS MATERIALS

HAZARDOUS PRESSURE sonal injury, pump damage or property damage.

Do not exceed the maximum inlet air pressure as stated on the pump model plate.

Be sure material hoses and other components are able to withstand fl uid pressures developed by this pump.

Check all hoses for damage or wear. Be certain dispensing device is clean and in proper working condition.

WARNING ing in severe injury or death. Ground pump and pumping system.

Sparks can ignite fl ammable material and vapors.

The pumping system and object being sprayed must be grounded when it is pumping, fl ushing, recirculating or spraying fl ammable materials such as paints, solvents, lacquers, etc. or used in a location where surrounding atmosphere is conducive to spontaneous combustion.

Ground the dispensing valve or device, containers, hoses and any object to which material is being pumped.

Secure pump, connections and all contact points to avoid vibration and generation of contact or static spark.

Consult local building codes and electrical codes for specifi c grounding requirements.

After grounding, periodically verify continuity of electrical path to ground. Test with an ohmmeter from each component (e.g., hoses, pump, clamps, container, spray gun, etc.) to ground to insure continuity.

Ohmmeter should show 0.1 ohms or less.

Submerse the outlet hose end, dispensing valve or device in the material being dispensed if possible.

(Avoid free streaming of material being dispensed.)

Use hoses incorporating a static wire.

Use proper ventilation.

Keep infl ammables away from heat, open fl ames and sparks.

Keep containers closed when not in use.

WARNING

EXCESSIVE AIR PRESSURE. Can cause per-

STATIC SPARK. Can cause explosion result-

Pump exhaust may contain contaminants.

Can cause severe injury. Pipe exhaust away from work area and personnel.

In the event of a diaphragm rupture, material can be

Pipe the exhaust to a safe remote location when pumping hazardous or infl ammable materials.

Use a grounded 3/8” minimum i.d. hose between the

WARNING

HAZARDOUS PRESSURE. Can result in serious injury or property damage. Do not service or clean pump, hoses or dispensing valve while the system is pressurized.

Disconnect air supply line and relieve pressure from the system by opening dispensing valve or device and

/ or carefully and slowly loosening and removing outlet hose or piping from pump.

WARNING HAZARDOUS MATERIALS. Can cause serious injury or property damage. Do not attempt to return a pump to the factory or service center that contains hazardous material. Safe handling practices must y y y y comply with local and national laws and safety code requirements.

Obtain Material Safety Data Sheets on all materials from the supplier for proper handling instructions.

WARNING

EXPLOSION HAZARD. Models containing aluminum wetted parts cannot be used with 1,1,1-trichloroethane, methylene chloride or other halogenated hydrocarbon solvents which may react and explode.

Check pump motor section, fl uid caps, manifolds and all wetted parts to assure compatibility before using with solvents of this type.

CAUTION Verify the chemical compatibility of the pump wetted parts and the substance being pumped, flushed or recirculated. Chemical compatibility may change with temperature and concentration of the chemical(s) within the substances being pumped, fl ushed or circulated. For specifi c fl uid compatibility, consult the chemical manufacturer.

CAUTION Maximum temperatures are based on mechanical stress only. Certain chemicals will significantly reduce maximum safe operating temperature.

Consult the chemical manufacturer for chemical compatibility and temperature limits. Refer to PUMP DATA on page 1 of this manual.

CAUTION

Be certain all operators of this equipment have been trained for safe working practices, understand it’s limitations, and wear safety goggles / equipment when required.

CAUTION Do not use the pump for the structural support of the piping system. Be certain the system components are properly supported to prevent stress on the pump parts.

Suction and discharge connections should be fl exible connections (such as hose), not rigid piped, and should be compatible with the substance being pumped.

CAUTION

Prevent unnecessary damage to the pump.

Do not allow pump to operate when out of material for long periods of time.

Disconnect air line from pump when system sits idle for long periods of time.

CAUTION Use only genuine ARO® replacement parts to assure compatible pressure rating and longest service life.

NOTICE Install the pump in the vertical position.

The pump may not prime properly if the balls do not check by gravity upon start-up.

NOTICE

Re-torque all fasteners before operation.

Creep of housing and gasket materials may cause fasteners to loosen. Re-torque all fasteners to insure against fl uid or air leakage.

NOTICE Replacement warning labels are available upon request: “Static Spark” pn \ 93616-1, Diaphragm

Rupture” pn \ 93122.

WARNING

CAUTION

NOTICE

= Hazards or unsafe practices which could result in severe personal injury, death or substantial property damage.

= Hazards or unsafe practices which could result in minor personal injury, product or property damage.

= Important installation, operation or maintenance information.

Page 2 of 8 PD07P-X-X (en)

GENERAL DESCRIPTION

The ARO diaphragm pump off ers high volume delivery even at low air pressure and a broad range of material compatibility options are available. Refer to the model and option chart.

ARO pumps feature stall resistant design, modular air motor

/ fl uid sections.

Air operated double diaphragm pumps utilize a pressure differential in the air chambers to alternately create suction and a positive fluid pressure in the fluid chambers, ball checks insure a positive fl ow of fl uid.

Pump cycling will begin as air pressure is applied and it will continue to pump and keep up with the demand. It will build and maintain line pressure and will stop cycling once maximum line pressure is reached (dispensing device closed) and will resume pumping as needed.

AIR AND LUBE REQUIREMENTS

y y

WARNING EXCESSIVE AIR PRESSURE. Can cause pump damage, personal injury or property damage.

A filter capable of filtering out particles larger than 50 microns should be used on the air supply. There is no lubrication required other than the “O” ring lubricant which is applied during assembly or repair.

If lubricated air is present, make sure that it is compatible with the “O” rings and seals in the air motor section of the pump.

OPERATING INSTRUCTIONS

y y y y y

Always flush the pump with a solvent compatible with the material being pumped if the material being pumped is subject to “setting up” when not in use for a period of time.

Disconnect the air supply from the pump if it is to be inactive for a few hours.

The outlet material volume is governed not only by the air supply, but also by the material supply available at the inlet. The material supply tubing should not be too small or restrictive. Be sure not to use hose which might collapse.

When the diaphragm pump is used in a forced-feed

(fl ooded inlet) situation, it is recommended that a “check valve” be installed at the air inlet.

Secure the diaphragm pump legs to a suitable surface to insure against damage by vibration.

MAINTENANCE

y y y y y

Certain ARO “Smart Parts” are indicated which should be available for fast repair and reduction of down time.

Provide a clean work surface to protect sensitive internal moving parts from contamination from dirt and foreign matter during service disassembly and reassembly.

Keep good records of service activity and include the pump in preventive maintenance program.

Service kits are available to service two separate diaphragm pump functions: 1. AIR SECTION, 2. FLUID SEC-

TION. The Fluid Section is divided further to match typical active Material Options.

Before disassembling, empty captured material in the outlet manifold by turning the pump upside down to drain material from the pump.

y Hytrel® is registered trademarks of the DuPont Company y Santoprene® is a registered trademark of Monsanto Company, licensed to Advanced Elastomer Systems, L.P. y y Lubriplate® is a registered trademark of Lubriplate Division (Fiske Brothers Refi ning Company) y ARO® is a registered trademark of Ingersoll-Rand Company y

PD07P-X-X (en) Page 3 of 8

PARTS LIST / PD07P-X-X FLUID SECTION

 637427-XX Fluid Section Service Kits include: Balls (see Ball Option, refer to -XX in chart below), Diaphragms (see Diaphragm Option, refer to -XX in chart below), and item 19 (listed below) plus items 144, 174 and 94276 Lubriplate® FML-2 grease (page 6).

SEAT OPTIONS

PD07P-XPS-XXX

“21”

-XXX Seat Qty [Mtl]

-PXX 96572-1 (4) [P]

BALL OPTIONS

PD07P-XPS-PXX

 “22” (3/4” diameter)

-XXX Ball Qty [Mtl]

-XAX 93100-E (4) [Sp]

-XCX 93100-C (4) [H]

-XTX 93100-4 (4) [T]

MATERIAL CODE

[GFN] = Glass Filled Nylon

[SS] = Stainless Steel

[T] = PTFE

DIAPHRAGM OPTIONS PD07P-XPS-PXX

-XXX

 Service Kit

-XX = (Ball)

 “7”  “8”  “19”

-XX = (Diaphragm) Diaphragm Qty [Mtl] Diaphragm Qty [Mtl] “O” Ring

(3/32” x 1-5/16” o.d.)

Qty [Mtl]

-XXA 637427-XA

-XXC 637427-XC

-XXT 637427-XT

93465

93465-9

93111

(2)

(2)

(2)

[Sp]

[H]

[T]

- - - - -

- - - - -

93465

- - -

- - -

(2)

- - -

- - -

[Sp]

93763

Y325-122

93265

(4)

(4)

(4)

[E]

[B]

[T]

Item Description (size)

† 1 Connecting Rod

5 Diaphragm Washer

6 Diaphragm Nut (5/16” - 18)

15 Fluid Cap

26 Flange Bolt (5/16” - 18 x 7/8”)

27 Bolt (5/16” - 18 x 1-1/4”)

29 Hex Flange Nut (5/16" - 18)

Qty Part No.

(1) 96379

(2) 94645

(2) 93103-7

(2) 95732-1

(4) 96176

(20) 93095

(20) 93886

COMMON PARTS

[Mtl]

[SS]

[GFN]

[P]

[P]

[SS]

[SS]

[SS]

Item Description (size)

60 Inlet Manifold

PD07P-APS-PXX (N.P.T.)

PD07P-BPS-PXX (BSP)

61 Outlet Manifold

PD07P-APS-PXX (N.P.T.)

PD07P-BPS-PXX (BSP)

77 Logo Plate

Qty Part No.

(1) 96605-1

(1) 96605-2

(1) 96603-1

(1) 96603-2

(2) 93264

[Mtl]

[P]

[P]

[P]

[P]

[A]

† “Smart Parts”, keep these items on hand in addition to the service kit for fast repair and reduction of down time.

TYPICAL CROSS SECTION

Page 4 of 8

Figure 2

PD07P-X-X (en)

PARTS LIST / PD07P-X-X FLUID SECTION

FOR THE AIR MO-

TOR SECTION, SEE

PAGES 6 & 7.

COLOR CODE

Material Color Color

Santoprene Tan Tan

PTFE White White

5

7

3

26 ( „

61

1

2 4

Torque Sequence

8

6

„ 27 1 œ 5 7 6 (

22

21

19 œ

29 ( „

60

29 ( „

Figure 3

View for PD07P-XPS-PXT (PTFE diaphragm) confi guration only.

Fluid side PTFE (white) 7

PD07P-X-X (en)

8 Air side Santoprene (tan)

) TORQUE REQUIREMENTS (

NOTE: DO NOT OVERTIGHTEN FASTENERS.

(6) Diaphragm nut, 95 - 105 in. lbs (10.7 - 11.9 Nm).

(26) Bolt, 50 - 60 in. lbs (5.6 - 6.8 Nm), / alternately and evenly, then retorque after initial run-in.

(29) Nut, 50 - 60 in. lbs (5.6 - 6.8 Nm), / alternately and evenly, then retorque after initial run-in.

LUBRICATION / SEALANTS

œ Apply Lubriplate FML-2 grease (94276) to all “O” rings, “U” cups and mating parts.

€ Apply pipe sealant to threads.

„ Apply anti-seize compound to threads and bolt and nut fl ange heads which contact pump case when using stainless steel fasteners.

Page 5 of 8

77

15

27 „

22

21

19 œ

PARTS LIST / PD07P-X-X AIR MOTOR SECTION

9 Indicates parts included in 637428 air section repair kit.

Item Description (size)

AIR MOTOR PARTS LIST

(Qty) Part No.

[Mtl] Item Description (size)

101 Center Body

103R Cover (right side)

103L Cover (left side)

107 Plug, Small

111 Major Valve Spool

118 Actuator Pin

121 Washer

123 Screw (#4 - 20 x 1/2”)

(1) 96315

(1) 96091

(1) 96351

(1) 96353

[PPG]

[D]

[D]

[D]

(1) 95919 [D]

(2) 94874-1 [SS]

(2) 96092

(8) 96093

[D]

[SS]

™ 129 Exhaust Cover (optional)

™ 130 Gasket (optional)

9 132 Air Manifold Gasket

134 Flange Bolt (1/4” - 20 x 5-3/4”)

135 Valve Block

136 Plug, Large

(1) 67367

(1) 67366

(1) 93107

(1) 96214-1

(4) 94871

(1) 96204

(1) 96352

9 137 “O” Ring (1/16” x 1-5/8” o.d.)

9 138 “U” Cup Packing (1/8” x 1” o.d.)

(3) Y325-29

(1) 94395

9 139 “U” Cup Packing (1/8” x 1-7/16” o.d.) (1) 96383

140 Valve Insert (1) 93276

[D]

[B]

[U]

[U]

[CK]

[PPG]

[PPG]

[SY]

[B]

[SS]

[PPG]

(Qty) Part No.

[Mtl]

141 Valve Plate (1) 96173

9 144 “U” Cup Packing (3/16” x 1” o.d.) (2) Y187-48

9 166 “O” Ring (1/16” x 1-1/4” o.d.) (1) Y325-24

9 167 Pilot Piston (includes 168 and 169) (1) 67382

168 “O” Ring (1/16” x 7/16” o.d.) (2) 96459

[CK]

[B]

[B]

[D]

9

9

169 “U” Cup Packing (1/8" x 5/8" o.d.) (1) 96384

170 Spool Bushing

171 “O” Ring

173 “O” Ring

(1/16” x 13/16” o.d.)

(3/16” x 7/8” o.d.)

9 174 “O” Ring (3/32” x 11/32” o.d.)

9 200 Porting Gasket

201 Muffl (optional)

(1) 96090

(2) Y325-17

[U]

[U]

(2) Y325-115 [B]

(2) Y325-105

(1) 96364

(1) 93110

[D]

[B]

[B]

[B]

[C]

™ 232 “O” Ring (1/16” x 3/8” o.d.)(optional) (4) Y325-10

™ Ported Exhaust Kit (includes items

129, 130 and 232) (optional)

(1) 637438

[B]

- - -

9 Lubriplate FML-2 Grease

Lubriplate Grease, 10 Pack

(1) 94276

637308

[B] = Nitrile

[C] = Carbon Steel

[CK] = Ceramic

[D] = Acetal

MATERIAL CODE

[PPG] = Glass Filled Polypropylene

[SS] = Stainless Steel

[SY] = Syn-Seal

[U] = Polyurethane

DIAPHRAGM PUMP SERVICE

GENERAL SERVICE NOTES: y Inspect and replace old parts with new parts as necessary. Look for deep scratches on metallic surfaces, and nicks or cuts in “O” rings.

y Tools needed to complete disassembly and repair: y 7/8” socket or wrench, 1/2” socket or wrench, 3/8” socket or wrench, 3/8” Allen wrench, T-10 Torx screwdriver, torque wrench (measuring inch pounds), “O” ring pick.

y y y lent “O” ring lubricant.

Connecting rod (1) should be installed using 96571 bullet, included in service kit.

Install (5) washers with i.d. chamfer toward diaphragm.

When replacing PTFE diaphragms, install the 93465

Santoprene diaphragm behind the

PTFE

diaphragm.

AIR MOTOR SECTION SERVICE

Service is divided into two parts - 1. Pilot Valve, 2. Major

Valve.

y Air Motor Section service is continued from Fluid Section repair.

1.

2.

3.

4.

5.

6.

7.

8.

FLUID SECTION DISASSEMBLY

Remove (61) top manifold.

Remove (19) “O” rings, (21) seats and (22) balls.

Remove (60) bottom manifold.

Remove (19) “O” rings, (21) seats and (22) balls.

Remove (15) fl uid caps.

Remove (6) diaphragm nut, (7) or (7 / 8) diaphragms and

(5) washer.

Remove (1) connecting rod from air motor.

Carefully remove remaining (6) diaphragm nut, (7) or (7

/ 8) diaphragms and (5) washer from (1) connecting rod.

Do not mar surface of connecting rod.

FLUID SECTION REASSEMBLY

y y

Reassemble in reverse order.

Lubricate (1) connecting rod with Lubriplate or equiva-

1.

2.

PILOT VALVE DISASSEMBLY

Remove (123) screws, releasing (103) covers, (121) washers, (118) actuator pins and (167) pilot piston.

Remove (170) spool bushing and inspect inner bore of bushing for damage.

PILOT VALVE REASSEMBLY

1.

2.

3.

4.

5.

Clean and lubricate parts not being replaced from service kit.

Assemble (171) “O” rings to (170) bushing and assemble bushing into (101) center body.

Lubricate and assemble (167) pilot piston assembly into

(170) bushing.

Assemble (173 and 174) “O” rings and (121) washers to

(103) covers, then insert (118) actuator pins through assembly.

Assemble (144) “U” cups (note the lip direction) and (103) covers to (101) center body, securing with (123) screws.

NOTE: Tighten (123) screws to 4 - 6 in. lbs (0.45 - 0.68 Nm).

Page 6 of 8 PD07P-X-X (en)

PARTS LIST / PD07P-X-X AIR MOTOR SECTION

PILOT VALVE PARTS

œ 144 118 169 œ 168 œ 171 œ 232 130

637438 (optional)

129 201 (optional)

) 123

103L

œ 173

œ 174 121 167 170

140 132

107

œ 137

œ 166

135

) 134

œ 138

œ 139

œ 137

129

144 œ

103R

123 (

MAJOR VALVE

141 œ 200 œ

111

136

101

Figure 4

118 121 174 œ 173 œ

PILOT VALVE PARTS

) TORQUE REQUIREMENTS (

NOTE: DO NOT OVERTIGHTEN FASTENERS.

(123) Torque to 4 - 6 in. lbs (0.45 - 0.68 Nm).

(134) Torque to 15 - 20 in. lbs (1.7 - 2.3 Nm), wait 10 minutes, then re-torque to 15 - 20 in. lbs (0.45 - 0.68 Nm).

LUBRICATION / SEALANTS

œ Apply Lubriplate FML-2 grease to all “O” rings, “U” cups and mating parts.

MAJOR VALVE DISASSEMBLY

1.

2.

3.

4.

Pull (135) valve block and components from (101) center body.

Remove (132) gasket, (141) valve plate and (140) valve insert from (135) valve block.

Remove (134) bolts, releasing (107 and 136) plugs and

(111) spool.

1.

2.

3.

4.

5.

6.

7.

MAJOR VALVE REASSEMBLY

Assemble new (138 and 139) “U” cups on (111) spool -

LIPS MUST FACE EACH OTHER .

Assemble (137) “O” rings to (136) large plug.

Assemble (137 and 166) “O” rings to (107) small plug.

Insert (111) spool into (136) large plug, then insert (136) large plug into (135) valve block, being sure the (111) spool is rotated to accept (140) valve insert.

Assemble (107) small plug into (135) valve block.

Assemble (140) valve insert and (141) valve plate to

(135) valve block. NOTE: Assemble (140) valve insert with

“dished” side toward (141) valve plate. Assemble (141) valve plate with identifi cation dot toward (132) gasket.

Assemble (132 and 200) gaskets, (135) valve block and

(129) muffler assembly to (101) center body, securing with (134) bolts. NOTE: Tighten (134) bolts to 15 - 20 in. lbs (1.7 - 2.3 Nm).

PD07P-X-X (en) Page 7 of 8

Product discharged from air exhaust.

y y

Check for diaphragm rupture.

Check tightness of (6) diaphragm nut.

TROUBLE SHOOTING

Air bubbles in product discharge.

y y y

Check connections of suction plumbing.

Check “O” rings between intake manifold and fl uid caps.

Check tightness of (6) diaphragm nut.

Pump blows air out main exhaust when stalled on either stroke.

y y y

Check “U” cups on (111) spool in major valve.

Check (141) valve plate and (140) insert for wear.

Check (169) “U” cup on (167) pilot piston.

Low output volume.

y y y

Check air supply.

Check for plugged outlet hose.

For the pump to prime itself, it must be mounted in the vertical position so that the balls will check by gravity.

y y y

Check for pump cavitation - suction pipe should be sized at least as large as the inlet thread diameter of the pump for proper fl ow if high viscosity fl uids are being pumped.

Suction hose must be non-collapsible type, capable of pulling a high vacuum.

Check all joints on the intake manifolds and suction connections. These must be air tight.

Inspect the pump for solid objects lodged in the diaphragm chamber or the seat area.

DIMENSIONAL DATA

Dimensions shown are for reference only, they are displayed in inches and millimeters (mm).

Air Inlet 1/4 - 18 P.T.F. SAE Short

(Outlet) Q

A

P

E

F

Q

(Inlet)

N

D

G B

K M

L C J

DIMENSIONS

A - 10-1/16” (254.2 mm) E - 6-3/4” (171.0 mm) J - 5-17/32" (140.2 mm) N - 6-5/16" (160.5 mm)

B - 10-3/32” (256.1 mm) F - 6-1/32” (153.1 mm) K - 5/16” (8.0 mm) P - 8-7/8” (225.3 mm)

C - 6-3/16” (157.1 mm) G - 10-29/32” (276.8 mm) L - 1-15/16” (48.9 mm) Q - see below

D - 2” (51.0 mm) H - 4-29/32” (124.2 mm) M - 3/8” (9.6 mm)

Pump Model

PD07P-APS-PXX

“Q” Material Inlet / Outlet

3/4 - 14 N.P.T.F. - 1

PD07P-BPS-PXX Rp 3/4 (3/4 - 14 BSP, parallel)

H

Figure 5

Page 8 of 8

PN 97999-1223

PD07P-X-X (en)