ES-24-250W, ES-24-500W Quick Start Guide
Package Contents
EdgeSwitch Mounting Screws (Qty. 4) Cage Nuts (Qty. 4)
Power Cord
Installation Requirements
Phillips screwdriver
Standard-sized, 19" wide rack with a minimum of 1U height available
For indoor applications, use Category 5 (or above) UTP cabling approved for indoor use.
For outdoor applications, shielded Category 5 (or above) cabling should be used for all wired Ethernet connections and should be grounded through the AC ground of the power supply.
We recommend that you protect your networks from harmful outdoor environments and destructive ESD events with industrial-grade, shielded Ethernet cable from Ubiquiti. For more details, visit: ui.com/toughcable
Note: Although the cabling can be located outdoors, the EdgeSwitch itself should be housed inside a protective enclosure.
Hardware Overview
ES-24-250W, ES-24-500W Quick Start Guide
System LED
Note: The System LED functionality has been updated with rmware v1.8.0. We recommend that you update the EdgeSwitch to the latest rmware.
Flashing White
White
Blue
Steady Blue with Occasional
Flashing
Quickly Flashing Blue
Bootup in progress.
Ready for use, not connected to Ubiquiti® Network
Management System (UNMS™). See “UNMS
Management” .
Ready for use, connected to UNMS.
Ready for use, unable to connect to UNMS, check connection to UNMS server.
Used to locate a device in UNMS.
Alternating
Blue/White
RJ45 PoE LED (Ports 1 - 24)
Firmware upgrade in progress.
Off
Amber
No PoE
IEEE 802.3af/802.3at
Green 24V Passive
RJ45 Speed/Link/Activity LED (Ports 1 - 24)
Off
Amber
No Link
Link Established at 10/100 Mbps
Green
Link Established at 1000 Mbps (1 Gbps)
Flashing Indicates Activity
SFP Speed/Link/Activity LED (Ports 1 - 2)
Off No Link
Green
Link Established at 1 Gbps
Flashing Indicates Activity
RJ45 (Ports 1 - 24)
RJ45 ports support Power over Ethernet (PoE) and 10/100/1000 Ethernet connections.
SFP (Ports 1 - 2)
Hot-swappable SFP ports support 1 Gbps connections.
Reset Button
Click here to learn how to reset an EdgeSwitch to factory defaults.
Console Port
RJ45 serial console port for Command Line Interface (CLI) management.
Power Port
Connect the included Power Cord to the Power port.
Hardware Installation
1.
2.
ES-24-250W, ES-24-500W Quick Start Guide
OR
3.
ES-24-250W, ES-24-500W Quick Start Guide
Note: The PoE settings for ports 1-24 are set to PoE+ auto by default, so 802.3af/at devices can be plugged in and automatically receive PoE. For instructions on how to enable 24V passive PoE, refer to
“Con guring PoE Settings” .
Connecting SFP
1.
2.
ES-24-250W, ES-24-500W Quick Start Guide
3.
For information about compatible ber SFP modules, visit: ubnt.link/SFP_DAC_Compatibility
Accessing the Con guration Interface
The EdgeSwitch is set to DHCP by default, so it will try to automatically obtain an IP address. If that fails, then it will use the default fallback IP address, 192.168.1.2. Proceed to the appropriate section, DHCP or
“Fallback IP Address” :
DHCP
Use one of the following methods:
Let the EdgeSwitch obtain an IP address and then check the DHCP server to see which IP address was assigned.
To log in, follow these steps:
1. Launch your web browser. Type the appropriate IP address in the address eld. Press enter
(PC) or return (Mac).
2. Enter ubnt in the Username and Password elds. Click Sign In.
3. The EdgeSwitch Con guration Interface will appear. Customize additional settings as needed.
For more information on PoE con guration, refer to “Con guring PoE Settings”
. For more information, refer to the EdgeSwitch documentation, which is available at ui.com/download/edgemax
Fallback IP Address
1. Ensure that your computer (or other host machine) is connected to the EdgeSwitch.
2. Con gure the Ethernet adapter on your host system with a static IP address on the
192.168.1.x subnet.
4. Enter ubnt in the Username and Password elds. Click Sign In.
5. The EdgeSwitch Con guration Interface will appear. Go to Settings .
6. Change the IP Address to a unique IP address. Click Apply.
ES-24-250W, ES-24-500W Quick Start Guide
Note: If you change the IP settings, then the session will be cut off, and you will need to reconnect to the EdgeSwitch using the new IP address.
Customize additional settings as needed. For more information on PoE con guration, refer to
“Con guring PoE Settings”
.
UNMS Management
You can manage your device using UNMS, which lets you con gure, monitor, upgrade, and back up your devices using a single application. Get started at www.unms.com
Con guring PoE Settings
The PoE settings for ports 1-24 are set to PoE+ by default, so 802.3af/at devices can be plugged in and automatically receive PoE.
WARNING: Before activating 24V passive PoE, ensure that the connected device supports PoE and the supplied voltage.
1. Go to Dashboard .
2. For the Ethernet port you want to con gure, click the PoE drop-down menu.
ES-24-250W, ES-24-500W Quick Start Guide
3. Select the appropriate mode: Off, 24V, or PoE+.
For more information, refer to the EdgeSwitch documentation, which is available at ui.com/download/edgemax
Speci cations
ES-24-250W/ES-24-500W
485 x 43.7 x 285.4 mm (19.09 x 1.72 x 11.24") Dimensions
Weight
ES-24-250W
ES-24-500W
Total Non-Blocking Line Rate
Max. Power Consumption
ES-24-250W
ES-24-500W
Power Method
Power Supply
ES-24-250W
ES-24-500W
LEDs Per Port
Serial Console Port
RJ45 Data Ports
SFP Data Ports
Interfaces
Networking Interfaces
4.7 kg (10.4 lb)
4.8 kg (10.6 lb)
26 Gbps
250W
500W
100-240VAC/50-60 Hz, Universal Input
AC/DC, Internal, 250W DC
AC/DC, Internal, 500W DC
N/A
PoE, Speed/Link/Activity
Speed/Link/Activity
Management Interface
Rack-Mount
ESD/EMP Protection
Shock and Vibration
(24) 10/100/1000 Mbps RJ45 Ethernet Ports
(2) 1 Gbps SFP Ethernet Ports
(1) RJ45 Serial Port, Ethernet In/Out Band
Yes, 1U High
Air: ± 24 kV, Contact: ± 24 kV
ETSI300-019-1.4 Standard
Operating Temperature
Operating Humidity
Certi cations
-5 to 40° C (23 to 104° F)
5 to 95% Noncondensing
CE, FCC, IC
PoE Per Port
PoE Interfaces
Max. PoE+ Wattage per Port by PSE
Voltage Range 802.3at Mode
Max. Passive PoE Wattage per Port
24V Passive PoE Voltage Range
POE+ IEEE 802.3af/at (Pins 1, 2+; 3, 6-)
24VDC Passive PoE (Pins 4, 5+; 7, 8-)
34.2W
50–57V
17W
20-27V
Safety Notices
1. Read, follow, and keep these instructions.
2. Heed all warnings.
3. Only use attachments/accessories speci ed by the manufacturer.
WARNING: Failure to provide proper ventilation may cause re hazard. Keep at least 20 mm of clearance next to the ventilation holes for adequate air ow.
WARNING: To reduce the risk of re or electric shock, do not expose this product to rain or moisture.
WARNING: Do not use this product in location that can be submerged by water.
WARNING: Avoid using this product during an electrical storm. There may be a remote risk of electric shock from lightning.
Electrical Safety Information
1. Compliance is required with respect to voltage, frequency, and current requirements indicated on the manufacturer’s label. Connection to a different power source than those speci ed may result in improper operation, damage to the equipment or pose a re hazard if the limitations are not followed.
2. There are no operator serviceable parts inside this equipment. Service should be provided only by a quali ed service technician.
3. This equipment is provided with a detachable power cord which has an integral safety ground wire intended for connection to a grounded safety outlet.
a. Do not substitute the power cord with one that is not the provided approved type. Never use an adapter plug to connect to a 2-wire outlet as this will defeat the continuity of the grounding wire.
b. The equipment requires the use of the ground wire as a part of the safety certi cation, modi cation or misuse can provide a shock hazard that can result in serious injury or death.
c. Contact a quali ed electrician or the manufacturer if there are questions about the installation prior to connecting the equipment.
d. Protective earthing is provided by Listed AC adapter. Building installation shall provide appropriate short-circuit backup protection.
Limited Warranty
ui.com/support/warranty
The limited warranty requires the use of arbitration to resolve disputes on an individual basis, and, where applicable, specify arbitration instead of jury trials or class actions.
Compliance
FCC
Changes or modi cations not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions.
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operations of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
ISED Canada
CAN ICES-3(A)/NMB-3(A)
Australia and New Zealand
Warning: This equipment is compliant with Class A of CISPR 32. In a residential environment this equipment may cause radio interference.
CE Marking
CE marking on this product represents the product is in compliance with all directives that are applicable to it.
WEEE Compliance Statement
Declaration of Conformity
Online Resources
ES-24-250W, ES-24-500W Quick Start Guide
© 2020 Ubiquiti Inc. All rights reserved.
