advertisement
BAT.Trusslight RGBW
LED spotlight
Musikhaus Thomann
Thomann GmbH
Hans-Thomann-Straße 1
96138 Burgebrach
Germany
Telephone: +49 (0) 9546 9223-0
E-mail: [email protected]
Internet: www.thomann.de
17.03.2021, ID: 412271 (V3)
Table of contents
Table of contents
BAT.Trusslight RGBW
LED spotlight
3
Table of contents
4 BAT.Trusslight RGBW
LED spotlight
BAT.Trusslight RGBW
LED spotlight
5
General information
1 General information
This user manual contains important information on the safe operation of the device. Read and follow all safety notes and all instructions. Save this manual for future reference. Make sure that it is available to all persons using this device. If you sell the device to another user, be sure that they also receive this manual.
Our products and user manuals are subject to a process of continuous development. We there‐ fore reserve the right to make changes without notice. Please refer to the latest version of the user manual which is ready for download under www.thomann.de
.
6 BAT.Trusslight RGBW
LED spotlight
General information
1.1 Further information
On our website ( www.thomann.de) you will find lots of further information and details on the following points:
Download
Keyword search
Service
This manual is also available as PDF file for you to download.
Use the search function in the electronic version to find the topics of interest for you quickly.
Online guides
Our online guides provide detailed information on technical basics and terms.
Personal consultation For personal consultation please contact our technical hotline.
If you have any problems with the device the customer service will gladly assist you.
BAT.Trusslight RGBW
LED spotlight
7
General information
1.2 Notational conventions
This manual uses the following notational conventions:
Letterings The letterings for connectors and controls are marked by square brackets and italics.
Examples: [VOLUME] control, [Mono] button.
1.3 Symbols and signal words
In this section you will find an overview of the meaning of symbols and signal words that are used in this manual.
8 BAT.Trusslight RGBW
LED spotlight
Signal word
DANGER!
WARNING!
NOTICE!
Warning signs
General information
Meaning
This combination of symbol and signal word indicates an immediate dangerous situation that will result in death or serious injury if it is not avoided.
This combination of symbol and signal word indicates a pos‐ sible dangerous situation that can result in death or serious injury if it is not avoided.
This combination of symbol and signal word indicates a pos‐ sible dangerous situation that can result in material and environmental damage if it is not avoided.
Type of danger
Warning – high-voltage.
Warning – dangerous optical radiation.
BAT.Trusslight RGBW
LED spotlight
9
General information
Warning signs Type of danger
Warning – suspended load.
Warning – danger zone.
10 BAT.Trusslight RGBW
LED spotlight
Safety instructions
2 Safety instructions
Intended use This device is intended for use as an electronic lighting effect by means of LED technology. The device is designed for professional use only and is not suitable for use in households. Use the device only as described in this user manual. Any other use or use under other operating con‐ ditions is considered to be improper and may result in personal injury or property damage. No liability will be assumed for damages resulting from improper use.
This device may be used only by persons with sufficient physical, sensorial, and intellectual abilities and having corresponding knowledge and experience. Other persons may use this device only if they are supervised or instructed by a person who is responsible for their safety.
Extend the operating life of the device by regular breaks and by avoiding frequent switching on and off. The device is not suitable for continuous operation.
BAT.Trusslight RGBW
LED spotlight
11
Safety instructions
Safety
DANGER!
Danger for children
Ensure that plastic bags, packaging, etc. are disposed of properly and are not within reach of babies and young children. Choking hazard! Ensure that children do not detach any small parts (e.g. knobs or the like) from the unit. They could swallow the pieces and choke! Never let children unattended use electrical devices.
DANGER!
Electric shock caused by high voltages inside
Within the device there are areas where high voltages may be present. Never remove any covers. There are no user-serviceable parts inside. Do not use the device if covers, protectors or optical components are missing or damaged.
DANGER!
Electric shock caused by short-circuit
Always use proper ready-made insulated mains cabling (power cord) with a protective contact plug. Do not modify the mains cable or the plug. Failure to do so could result in electric shock/death or fire. If in doubt, seek advice from a registered electrician.
WARNING!
Eye damage caused by high light intensity
Never look directly into the light source.
12 BAT.Trusslight RGBW
LED spotlight
Safety instructions
WARNING!
Risk of epileptic shock
Strobe lighting can trigger seizures in photosensitive epilepsy. Sensitive persons should avoid looking at strobe lights.
WARNING!
Incorrect handling of lithium batteries can result in injury
In the event of a short circuit, overheating or mechanical damage, lithium batteries can cause severe injuries. Follow the advice on the correct handling of lithium batteries in the present section.
NOTICE!
Risk of fire
Do not block areas of ventilation. Do not install the device near any direct heat source. Keep the device away from naked flames.
NOTICE!
Operating conditions
This device has been designed for indoor use only. To prevent damage, never expose the device to any liquid or moisture. Avoid direct sunlight, heavy dirt, and strong vibrations. Only operate the device within the ambient conditions specified in the chapter
‘Technical specifications’ of this user manual. Avoid heavy temperature fluctuations and do not switch the device on immediately after it was exposed to temperature fluctuations (for example after transport at low outside temperatures). Dust and dirt inside can damage the unit. When operated in harmful ambient conditions (dust, smoke, nicotine, fog, etc.), the unit should be maintained by qualified service personnel at regular intervals to prevent overheating and other malfunction.
BAT.Trusslight RGBW
LED spotlight
13
Safety instructions
NOTICE!
Power supply
Before connecting the device, ensure that the input voltage (AC outlet) matches the voltage rating of the device and that the AC outlet is protected by a residual current circuit breaker. Failure to do so could result in damage to the device and possibly injure the user. Unplug the device before electrical storms occur and when it is unused for long periods of time to reduce the risk of electric shock or fire.
NOTICE!
Risk of fire due to incorrect polarity
Incorrectly inserted batteries may destroy the device or the batteries. Ensure that proper polarity is observed when inserting bat‐ teries.
NOTICE!
Possible damage by leaking batteries
Leaking batteries can cause permanent damage to the device. Take batteries out of the device if it is not going to be used for a longer period.
NOTICE!
Possible staining
The plasticiser contained in the rubber feet of this product may possibly react with the coating of your parquet, linoleum, laminate or PVC floor and after some time cause permanent dark stains. In case of doubt, do not put the rubber feet directly on the floor, but use felt-pad floor protectors or a carpet.
14 BAT.Trusslight RGBW
LED spotlight
Safety instructions
NOTICE!
Possible damage to lithium-ion batteries through incorrect storage
By deep discharge, lithium-ion batteries can be permanently damaged or lose some of their capacity. Before long breaks, charge the batteries to around 50 % of their capacity and then switch off the device. Store the device at room temperature or cooler in an envi‐ ronment as dry as possible. If the batteries are stored for a longer period, recharge them to 50 % every three months. Fully charge the batteries only shortly before use at room temperature.
BAT.Trusslight RGBW
LED spotlight
15
Features
3 Features
Special features of the device: n 3 four-colour LEDs (red, green, blue and white, 10 W each) n Operable in stand-alone mode or DMX n Control via DMX, the supplied infrared remote control or the buttons and display on the unit n Stand-alone operation with static colours n Sound control n Can be mounted on three-point trusses n Mounting plate for inclination adjustment n Battery or mains powered n Power adapter and infrared remote control included n Suitable for use in clubs, bars, theatres, exhibitions, etc. or for mobile use
For technological reasons, the light output of LEDs decreases over their lifetime. This effect increases with higher operating temperature. You can extend the service life of the illuminants by providing adequate ventilation and operating the LEDs with the lowest possible brightness.
16 BAT.Trusslight RGBW
LED spotlight
4 Installation
Installation
Unpack and check carefully there is no transportation damage before using the unit. Keep the equipment packaging. To fully protect the product against vibration, dust and moisture during transportation or storage use the original packaging or your own packaging material suitable for transport or storage, respectively.
WARNING!
Risk of injury caused by falling objects
Make sure that the installation complies with the standards and rules that apply in your country. Always secure the device with a secondary safety attachment, such as a safety cable or a safety chain.
BAT.Trusslight RGBW
LED spotlight
17
Installation
NOTICE!
Risk of overheating
The distance between light output and the illuminated surface must be more than 1.5 m (19.7in).
Provide sufficient ventilation.
The ambient temperature must always be below 40 °C (104 °F).
NOTICE!
Use of stands
When mounting the device onto a stand, ensure that the stand is in a safe and stable position and that the weight of the device does not exceed the maximum permissible load capacity of the stand.
18 BAT.Trusslight RGBW
LED spotlight
Mounting options
Installation
NOTICE!
Possible data transmission errors
For error-free operation make use of dedicated DMX cables and do not use ordi‐ nary microphone cables.
Never connect the DMX input or output to audio devices such as mixers or ampli‐ fiers.
You can install the device using a stand, as well as standing or hanging upside down. When in use, the device must always be attached to a solid surface or an approved truss. Use the threads provided for mounting.
Additionally secure the device by a safety cable against falling. Pull the safety cable through the safety cable eyelet on the top of the unit.
Always work from a stable platform whenever installing, moving or servicing the unit. In doing so, the area underneath the unit must be cordoned off.
BAT.Trusslight RGBW
LED spotlight
19
Installation
Please note that this device must not be connected to a dimmer.
Infrared sensor for the remote control
The infrared receiver for the IR remote control signals is located between the LEDs on the front panel of the device. Make sure it's not obstructed.
20 BAT.Trusslight RGBW
LED spotlight
Inserting the battery into the remote control
Installation
Press the lock of the battery holder to the centre of the housing and pull out the battery holder like a drawer. Insert the battery. The battery is correct if the positive pole points to the housing base of the remote control. Slide the battery holder back into the remote until it clicks into place.
When shipping, the battery is already installed in the remote and protected against discharge by a transparent plastic foil. Remove the plastic foil prior to first use.
BAT.Trusslight RGBW
LED spotlight
21
Installation
4.1 Dealing with lithium batteries
WARNING!
Incorrect handling of lithium batteries can result in injury
In the event of a short circuit, overheating or mechanical damage, lithium bat‐ teries can cause severe injuries.
Follow the advice on the correct handling of lithium batteries in the present sec‐ tion.
When handled correctly and appropriately lithium batteries pose no risk.
Store lithium batteries in a cool, dry place, ideally in the original packaging.
Store lithium batteries away from heat sources (e.g. radiators or sunlight). Lithium batteries are hermetically sealed. Never attempt to open a lithium battery.
If the battery housing is damaged small amounts of the electrolyte may leak out. If this should happen, seal the lithium battery in airtight packaging and wipe up the traces of electrolyte using absorbent paper towels. You must wear protective rubber gloves when doing so. Clean your hands and the affected surface thoroughly with cold water.
22 BAT.Trusslight RGBW
LED spotlight
Installation
Never attempt to recharge non-rechargeable lithium batteries. When charging lithium bat‐ teries you must use a suitable charging device intended for the purpose.
Before disposing of the device remove the lithium batteries. Protect used lithium batteries against potential short circuits, e.g. by covering the poles with adhesive tape.
Only use powder extinguishers or other suitable extinguishing agents to extinguish a burning lithium battery.
BAT.Trusslight RGBW
LED spotlight
23
Starting up
5 Starting up
Create all connections while the device is off. Use the shortest possible high-quality cables for all connections. Take care when running the cables to prevent tripping hazards.
24 BAT.Trusslight RGBW
LED spotlight
Connections in DMX mode
Starting up
Connect the DMX input of the device to the DMX output of a DMX controller or another DMX device. Connect the output of the first DMX device to the input of the second one, and so on to form a daisy chain. Always ensure that the output of the last DMX device in the daisy chain is terminated with a resistor (110 Ω, ¼ W).
BAT.Trusslight RGBW
LED spotlight
25
Connections and operating elements
6 Connections and operating elements
26 BAT.Trusslight RGBW
LED spotlight
Connections and operating elements
1 [BATTERY INDICATOR]
Remaining battery capacity display. When all the LEDs are on, the battery is fully charged. If only the red LED is on, the unit must be connected to the mains again to charge as soon as possible.
2 Display
3 Function buttons
[MENU]
Activates the main menu and toggles between menu items. Closes an opened submenu.
[UP] , [DOWN]
Toggles between the menu items of a menu level, increases or decreases the displayed value by one.
[ENTER]
Selects an option of the respective operating mode, confirms the set value.
4 [DMX IN]
DMX input
5 [DMX OUT]
DMX output
BAT.Trusslight RGBW
LED spotlight
27
Connections and operating elements
6 [POWER]
Connection socket for the 15 V power supply unit
7 [ON / OFF]
Main switch. Turns the device on and off
28 BAT.Trusslight RGBW
LED spotlight
Remote control
Connections and operating elements
BAT.Trusslight RGBW
LED spotlight
29
Connections and operating elements
8 Button to turn the device on and off
9 [DMX]
Button to switch between DMX and stand-alone mode
10 [SLAVE]
Button to switch between master and slave mode.
11 [AUTO 1] , [AUTO 2] , [SPEED]
Buttons to activate automatic mode 1 or 2 and to adjust the programme speed
12 [UP] , [DOWN]
Buttons to switch between programmes and to increase / decrease numeric values
13 Buttons for colour selection
Use n [W] for white light n [R] , [G] , or [B] for primary colours red, green and blue
14 [STROBE]
Button to turn the strobe effect on or off
30 BAT.Trusslight RGBW
LED spotlight
15 Numeric buttons 0 … 9 for direct value input
16 [SOUND 1] , [SOUND 2]
Buttons to activate sound-control mode 1 or 2
Connections and operating elements
BAT.Trusslight RGBW
LED spotlight
31
Operating
7 Operating
7.1 Starting the device
Using the main switch, turn the device on. The display shows the current operation mode.
7.2 Operating controls on the unit
Wait for approx. 15 seconds after confirming the last modification of the setting until the dis‐ play turns off. Now the settings are saved.
DMX mode, DMX address Press [MENU] , [UP] or [DOWN] repeatedly until the display shows ‘Addr’ . Confirm with [ENTER] .
Now you can set the number of the first DMX channel to be used by the device (DMX address).
Use [UP] and [DOWN] to select a value between 1 and 512 (display shows ‘A001’ … ‘A512’ ).
Confirm with [ENTER] .
32 BAT.Trusslight RGBW
LED spotlight
Sound control
Constant colour
Operating mode Auto
Operating mode Slave
Operating
Press [MENU] , [UP] or [DOWN] repeatedly until the display shows ‘Soun’ . Confirm with [ENTER] .
Use [UP] and [DOWN] to select the desired mode ‘Sou1’ or ‘Sou2’ . Confirm with [ENTER] .
Press [MENU] , [UP] or [DOWN] repeatedly until the display shows ‘Colo’ . Confirm with [ENTER] .
Use [UP] and [DOWN] to select a constant colour in a range from ‘Col1’ … ‘Col9’ or the option
‘AtF’ . Confirm with [ENTER]
In AtF mode, you can create custom colour mixes by adjusting the red, green, blue, and white colour intensities in a range from ‘1’ … ‘255’ . Confirm each colour setting with [ENTER] to change to the next colour in the menu.
Press [MENU] , [UP] or [DOWN] repeatedly until the display shows ‘Auto’ . Confirm with [ENTER] .
Use [UP] and [DOWN] to select the desired mode ‘Aut1’ or ‘Aut2’ . Confirm with [ENTER] . You can now set the program's speed between ‘SP 1’ and ‘SP 9’ .
Press [MENU] , [UP] or [DOWN] repeatedly until the display shows ‘SLav’ . Confirm with [ENTER] .
The display shows ‘Sla’ , the unit is now in Slave mode.
BAT.Trusslight RGBW
LED spotlight
33
Operating
Display software version Press [MENU] , [UP] or [DOWN] repeatedly until the display shows ‘uer’ . Confirm with [ENTER] .
The display shows the current software version.
7.3 Operating via IR remote control
Press [MENU] , [UP] or [DOWN] repeatedly until the display shows ‘reno’ . Confirm with [ENTER] .
Use [UP] and [DOWN] to select the option ‘on’ to operate the unit via the IR remote control.
Confirm with [ENTER] .
34 BAT.Trusslight RGBW
LED spotlight
7.4 Menu overview
Operating
BAT.Trusslight RGBW
LED spotlight
35
Operating
7.5 Functions in DMX mode
4
5
6
2
3
Channel
1
7
Value
0 … 255
0 … 255
0 … 255
0 … 255
0 … 255
0 … 16
16 … 95
0 … 15
16 … 31
32 … 47
48 … 63
Function
Master Dimmer (0 % to 100 %)
Intensity Red (0 % bis 100 %), if channel 6 = 16 … 95
Intensity Green (0 % to 100 %), if channel 6 = 16 … 95
Intensity Blue (0 % bis 100 %), if channel 6 = 16 … 95
Intensity White (0 % bis 100 %), if channel 6 = 16 … 95
Strobe effect (0 % to 100 %)
Program speed (0 % to 100 %)
Dimmer (0 % to 100 %)
Colour mixing with cross-fade 1
Colour mixing with cross-fade 2
Colour mixing with cross-fade 3
36 BAT.Trusslight RGBW
LED spotlight
Channel Value
64 … 79
80 … 95
96 … 111
112 … 127
128 … 143
144 … 159
160 … 175
176 … 191
192 … 207
208 … 223
224 … 239
240 … 255
Function
Colour mixing with cross-fade 4
Colour mixing with cross-fade 5
Colour change with strobe effect
Colour change with fade effect
Colour change
Colour mixing, colour change and blackout
Dimming with colour change
Reverse dimming with colour change
Dimming, reverse dimming
Alternate colour mixing
Sound mode 1
Sound mode 2
Operating
BAT.Trusslight RGBW
LED spotlight
37
Technical specifications
8 Technical specifications
Light source
Optical properties
Control
Number of DMX channels
Input connections
Output connections
Power consumption
Power supply
3 four-colour LEDs (red, green, blue and white, 8 W each)
Beam angle 25°
DMX, infrared remote control, buttons and display on the device
7
Power supply
DMX control
DMX control
24 W
Connection socket for power adapter
XLR chassis socket, 3-pin
XLR chassis socket, 3-pin
Power adapter, 100 - 240 V 50/60 Hz
Replaceable rechargeable battery pack, item # 385488
(lithium ion battery, 10.8 V, 1500 mAh)
38 BAT.Trusslight RGBW
LED spotlight
Operating voltage
Degree of protection
Mounting options
Dimensions (W × H × D)
Weight
Ambient conditions
Technical specifications
15 V / 3000 mA, centre positive
IP20 hanging, standing, tripod-mounted
157 mm × 142 mm × 152 mm
1.3 kg
Temperature range
Relative humidity
0 °C…40 °C
20 %…80 % (non-condensing)
BAT.Trusslight RGBW
LED spotlight
39
Technical specifications
Further information
Construction
LED type
Base housing
Fanless
Remote control wireless DMX
Housing colour
Up-Light x-in-1
Yes
No included
No
Black
40 BAT.Trusslight RGBW
LED spotlight
Plug and connection assignments
9 Plug and connection assignments
Introduction This chapter will help you select the right cables and plugs to connect your valuable equip‐ ment so that a perfect light experience is guaranteed.
Please take our tips, because especially in ‘Sound & Light’ caution is indicated: Even if a plug fits into a socket, the result of an incorrect connection may be a destroyed DMX controller, a short circuit or ‘just’ a not working light show!
DMX connections The unit offers a 3-pin XLR socket for DMX output and a 3-pin XLR plug for DMX input. Please refer to the drawing and table below for the pin assignment of a suitable XLR plug.
2
3
Pin
1
Configuration
Ground, shielding
Signal inverted (DMX–, ‘cold signal’)
Signal (DMX+, ‘hot signal’)
BAT.Trusslight RGBW
LED spotlight
41
Troubleshooting
10 Troubleshooting
NOTICE!
Possible data transmission errors
For error-free operation make use of dedicated DMX cables and do not use ordi‐ nary microphone cables.
Never connect the DMX input or output to audio devices such as mixers or ampli‐ fiers.
In the following we list a few common problems that may occur during operation. We give you some suggestions for easy troubleshooting:
42 BAT.Trusslight RGBW
LED spotlight
Troubleshooting
Symptom
Device not working, no light
Remedy
Check the mains connection and the main fuse.
Not responding to DMX controller 1. Check the DMX connectors and cables to see if they are properly linked.
The built-in battery can no longer be recharged
2. Check the address settings and the DMX polarity.
3. Try using another DMX controller.
4. Check whether the DMX cables run near or parallel to high-voltage cables that may cause damage or interfer‐ ence to the DMX interface circuit.
Do not attempt to replace the built-in battery yourself.
Please contact our service centre.
If the procedures recommended above do not succeed, please contact our Service Center. You can find the contact information at www.thomann.de
.
BAT.Trusslight RGBW
LED spotlight
43
Cleaning
11 Cleaning
Optical lenses
Fan grids
Clean the optical lenses, that are accessible from the outside, regularly in order to optimize the light output. The frequency of cleaning depends on the operating environment: wet, smoky or particularly dirty surroundings can cause more accumulation of dirt on the optics of the device.
n Clean with a soft cloth using our lamp and lens cleaner (item no. 280122).
n Always dry the parts carefully.
The fan grids of the device must be cleaned of any contamination, such as dust, etc. on a reg‐ ular basis. Before cleaning, switch off the device and disconnect mains-operated devices from the mains. Only use pH-neutral, solvent-free and non-abrasive cleaning agents. Clean the unit with a slightly damp lint-free cloth.
44 BAT.Trusslight RGBW
LED spotlight
Protecting the environment
12 Protecting the environment
Disposal of the packaging mate‐ rial
For the packaging, environmentally friendly materials have been chosen that can be supplied to normal recycling.
Ensure that plastic bags, packaging, etc. are properly disposed of.
Do not just dispose of these materials with your normal household waste, but make sure that they are collected for recycling. Please follow the notes and markings on the packaging.
Disposal of batteries
Batteries do contain some hazardous chemicals so they should not be thrown away with the normal household waste. They should be returned to the manufacturer for disposal or recycled elsewhere in accordance with your local regulations.
Dispose lithium batteries only in discharged condition. Remove lithium batteries from the device before disposal. Protect used lithium batteries against potential short circuits, e.g. by covering the poles with adhesive tape. Dispose the built-in lithium batteries together with the device. Please check for an appropriate reception facility.
BAT.Trusslight RGBW
LED spotlight
45
Protecting the environment
Disposal of your old device
This product is subject to the European Waste Electrical and Electronic Equipment Directive
(WEEE) in its currently valid version. Do not dispose with your normal household waste.
Dispose of this device through an approved waste disposal firm or through your local waste facility. When discarding the device, comply with the rules and regulations that apply in your country. If in doubt, consult your local waste disposal facility.
46 BAT.Trusslight RGBW
LED spotlight
Musikhaus Thomann · Hans-Thomann-Straße 1 · 96138 Burgebrach · Germany · www.thomann.de
advertisement