202220902-1020
Owner’s Guide and Installation Manual
PELLA
®
EXPRESS INSTALL
®
STORM DOOR MODELS
NOTE TO THE INSTALLER: This Owner’s Guide and Installation Manual is the property of the homeowner. Please leave it with the homeowner upon completion of the installation.
Recommended Tools
Tape Measure Power Drill Pencil Phillips Screwdriver #2
For safety reasons, the assistance of a second person is recommended when handling the door.
Read the legend below in order to easily follow along and install your storm door.
For reference, the storm door assembly is illustrated on page 2.
Legend
1 2 3
Follow the steps in order.
Steps in BLUE apply to LEFT HINGE
configurations
ONLY.
(Hinge side will be determined in a later step.)
Steps in GREEN apply to RIGHT HINGE
configurations
ONLY.
(Hinge side will be determined in a later step.)
To order replacement parts, call
888-646-5354 or visit us at www.pella.com
Please have your registration number ready when you contact us.
TROUBLE SHOOTING GUIDE
is located at the end of this manual.
Lay door flat.
Before discarding the carton, make sure ALL parts are accounted for.
Loose Parts
Loose Parts
Hardware Kit(s)
The carton material is recyclable
Storm Door Components
NOTE: Actual door styles may vary from illustrations, however, the installation steps will be the same.
Glass Insert
(may be sold separately)
Screen Insert
Drip Cap
Installation
Template
Glass Insert
(may be sold separately)
Screen Insert
Drip Cap
Installation
Template
Retainer Strips (4)
OR
Handle Set
(may be sold separately)
Screw Covers (3)
Door Frame with Hinge
Hinge Side Extender
Expander
Latch Side Extender
Retainer Strips (4)
OR
Handle Set
(may be sold separately)
Hardware
Lock Body
Latch Rail
Closer Kit
Screw Covers (3)
2
Door Frame with Hinge
Hinge Side Extender
Expander
Latch Side Extender
Hardware
Lock Body
Latch Rail
Closer Kit
Before you begin
a Determine the hinge side of your storm door.
b 1-in wide x 1-in deep mounting surface is required. Hinge-side shimming may be required to fit existing opening. c
Left Hinge Right Hinge
Shim on your hinge side, as determined above. Shim may be one long piece or small 8-in to 12-in sections. Use an appropriate shim thickness to reduce the opening as noted in the chart. Household shim materials may include paint stir sticks or wooden yardsticks.
d
Nominal
Door Sizes
36-in x 81-in
34-in x 81-in
32-in x 81-in
30-in x 81-in
Opening Width
(No shim required)
35-7/8 in – 36-in
33-7/8 in – 34-in
31-7/8 in – 32-in
29-7/8 in – 30-in
Opening Width
(Shim required)
36-1/16-in – 36-3/8-in
34-1/16-in – 34-3/8-in
32-1/16-in – 32-3/8-in
30-1/16-in – 30-3/8-in
Shim to this
Opening Width
35-7/8-in – 36-in
33-7/8-in – 34-in
31-7/8-in – 32-in
29-7/8-in – 30-in
Opening
Height
80-in to 81-in
Top View
1-in
House Door
1-in
Jamb
Storm Door Opening Width
Check for existing door hardware interference. If storm door hardware will interfere with your house door hardware, we recommend placing the storm door hinge on the opposite side. Nail shim in place.
e
Exterior Brick
Mold Trim
Verify house door trim is securely attached and square. If you removed an old storm door, you may wish to fill and paint any existing holes before proceeding.
LEFT
HINGE
DOORS shim this side
RIGHT
HINGE
DOORS shim this side
Shim(s)
Shim must not extend beyond entryway face
3
1 Turn door so the interior faces up.
Remove any shipping clips or retainer strips. Remove screen. Set aside lockbody and loose parts.
Remember this is the
INTERIOR SIDE of the door
S n a p
L i f t
Install
Both
Top and
Bottom
Install Both
Left and Right
4
2 Set glass insert into opening with
“Exterior Side” sticker facing down.
3 Install the short retainer strips into the top and bottom channels.
4 Install the long retainers into the side channels.
5 Locate the rail extenders. Slide the rail extender into the
5 bottom of the hinge rail. For LEFT HINGE installation, use installation, use the rail extender marked with an “R”.
installation, use the rail extender marked with an “R”.
6 6 the bottom of the door, with the with the slots to the interior.
Do NOT secure with screws at this time. Trim the expander sweep length leaving 1/8” past the expander edges.
LEFT
HINGE
SHOWN LEFT
HINGE
SHOWN
RIGHT
HINGE
SHOWN RIGHT
HINGE
SHOWN
7 Locate the screw template in Bag A of the Closer
Kit. Position it with the proper end UP based on your hinge position. Place the template tight against the hinge side of the door frame, and slide to the top.
8 Holding the template in place, install the placeholder screw into the center of hole. Do not tighten all of the way. Leave 1/8-in of the screw exposed. Remove and discard template.
4
Left Hinge Right Hinge
Left Hinge
Qty. 1 Placeholder Screw
#8 x 3/4” Pan Head
Actual Size
Right Hinge
5
7 Locate the screw template in Bag A of the Closer
Kit. Position it with the proper end UP based on your hinge position. Place the template tight against the hinge side of the door frame, and slide to the top.
Left Hinge
8 Holding the template in place, install the placeholder screw into the center of hole. Do not tighten all of the way. Leave 1/8-in of the screw exposed. Remove and discard template.
Right Hinge
Left Hinge
Right Hinge
Actual Size
#8x3/4 in. Pan Head
Placeholder Screw Qty 1
Left Hinge
6
Right Hinge
Left Hinge
Right Hinge
Actual Size
#8x3/4 in. Pan Head
Placeholder Screw Qty 1
9 Hang storm door onto door frame using the placeholder screw. The door will settle approximately 1/16-in. Tighten screw while pushing top of hinge rail tight against the door frame.
10 Install door installation screw from
Bag B in the lowest hole on the hinge rail, and secure door in opening.
PUSH
Qty. 1 Installation Screw
#8 x 3/4-in Pan Head
Actual Size
11 Slide rail extender to sill. Loosen door installation screw if needed and then retighten.
12 Install door installation screws from
Bag B on the inner side of hinge rail in remaining six locations.
Qty. 6
Actual Size
7
Push door tight against door frame. Install door installation screws from Bag B on the outer face of the hinge rail. Do not over tighten screws.
5
5
14
14
Cut extender weather stripping to length, remove adhesive backing and install.
15
15
Rest the drip cap on top of the door, using spacers for alignment.
Rest the drip cap on top of the door, using spacers for alignment. Close door and align the end of the drip cap with the outside edge of the hinge rail.
6
16
Secure drip cap with installation screws from
Bag B. Remove and discard the spacer clips.
Caulk along top edge of drip cap if desired.
17
Slide the remaining rail extender into the bottom of the latch rail. For LEFT HINGE installation, use the rail extender marked with an “R”. For RIGHT HINGE installation, use the rail extender marked with an “L”.
Qty. 3 Installation Screw
#8 x 3/4-in Pan Head
Actual Size
8 Remove clips after installing screws
Left Hinge
Right Hinge
16 Secure drip cap with installation screws from Bag B. Remove and discard the spacer clips. Caulk along top edge of drip cap if desired.
Qty. 3
Actual Size
17 Slide the remaining rail extender onto the bottom of the latch rail. For LEFT HINGE installation, use the rail extender marked with an “R”. For
RIGHT HINGE installation, use the rail extender marked with an “L”.
Remove clips after installing screws
Left Hinge Right Hinge
19 Verify that the door closes freely without hitting the latch rail. Align outside edge of the latch rail with outside edge of the drip cap.
20 Fasten the latch rail with door installation screws from Bag B.
Qty. 5 Installation Screw
#8 x 3/4-in Pan Head
Actual Size
21 Slide rail extender to the sill.
22 Cut extender weather stripping to length, remove adhesive backing and install.
23 Following the instructions in the handle kit, install the lock body and handle.
9
Handle Kit may be sold separately.
7
10
20 Fasten the latch rail with door installation screws from Bag B.
Qty. 5 Installation Screw
#8 x 3/4-in Pan Head
Actual Size
21 Slide rail extender to the sill.
22 Cut extender weather stripping to length, remove adhesive backing and install.
23 Following the instructions in the handle kit, install the lock body and handle.
Handle Kit may be sold separately.
24 Install screw cover strips (1 horizontal, 2 vertical).
1
2
8
25
Close the door. Adjust the bottom expander to lightly contact the sill. Install expander screws from Bag D.
Qty. 2 Installation Screw
#8 x 1/2-in Pan Head
Actual Size
11
Locate the two closer bases in the closer kit. Remove and discard the hole plugs.
LEFT HINGE Install Closers on this side
RIGHT HINGE Install Closers on this side
Right Hinge
Interior side of door
Determine which side to install the closers, based on your hinge installation.
Align Arrow with Pencil Mark
APPROX 1.5"
From inside your house, measure 1-1/2-in down from the top of the hinge mounting rail and mark with a pencil.
Measure 1-1/2-in up from the bottom of the hinge mounting rail and mark with pencil.
Align the arrow on the closer base with the mark you made, and rest the base against the back of the hinge mounting rail.
Rest Against
Back of Hinge
Mounting Rail
Secure base with four closer base screws. Repeat for second closer base, aligning base arrow with your mark.
Qty.
8 Closer Base Screw
#10 x 1 1/2-in Pan Head
Actual Size
Top
Closer
Bottom
Closer
Right Hinge
12 9
33 Locate the top and bottom closers.
Right Hinge
Top Closer
Left
Hinge
Illustration
TOP
Closer
BOTTOM
Closer
Attach jamb bracket to bottom closer with the short pin, positioning
One-Touch ® button facing up as shown.
Slide top and bottom closers onto their bases.
Rem ove
Disca rd
DOOR
BRACKET
Ins ert
Left Hinge
Illustration
JAMB
BRACKET i d
S l e
Leave Clip in Place
Attach door bracket to closer assembly with the long pin.
Close door.
Secure the door bracket with door bracket screws.
Top
Closer
Bottom
Closer
One-Touch
®
Button
Bottom Closer
Qty.
4 Door Bracket Screw
#10 x 5/8-in
Actual Size
Dis and ove
Discard clips
(top and bottom).
Adjustment Screw
Fast er er w
S
Adjust closer speed with adjustment screw.
10
TO CLOSE:
Nudge the door open slightly.
One-Touch ® Button
13
Care and Maintenance
Door
Cleaning
Glass
Cleaning
Handle
Cleaning
Use a soft cloth with any household grease-cutting cleaner to clean the door.
PLEASE NOTE: Thin marks on the painted surfaces of the door can be removed using turpentine and light rubbing with a clean cloth.
IMPORTANT: DO NOT use brass polish or steel wool on the bottom expander. Use a household grease-cutting cleaner or a mild soap and water solution.
PLAIN GLASS
DO NOT use an ammonia-based cleaner for the first cleaning of the glass.
FIRST CLEANING: Use a mixture of one part vinegar with four parts water to remove the protective coating (for shipping purposes) from the glass.
ROUTINE CLEANING: Use any household glass cleaner.
LOW-E GLASS
RECOMMENDED ROUTINE CLEANING: Clean the glass with plain water, using a clean soft sponge or lint-free cloth to remove as much surface grime from the glass as possible. If needed, wash the surface of the glass again with a solution of 80% water and
20% vinegar with a clean soft lint-free cloth. Dry with a new soft cloth. Cleaning may cause streaks when dried if the glass is exceptionally dirty. In this case repeat cleaning.
NOTE:
• Care must be exercised when using rubber squeegees on the coated surface, as they can leave streaks that are hard to remove if they are used incorrectly or are in poor condition.
• Never use ANY type of scraper or abrasive cleaner on the coated surface. Particles from these materials can be deposited on the coated surface and are very difficult to remove.
• For unusually hard to remove spots such as crayon or grease, isopropyl alcohol, GooGone ® or
GoofOff ® may be used. After spot cleaning, the full glass surface should be cleaned following the recommended routine cleaning instructions.
BRASS & NICKEL FINISHES
Routine Cleaning: Use a soft cloth with a mild soap and water solution to clean the surfaces. Apply a high quality, non-abrasive automobile wax to polish.
Note: NEVER use ammonia-based cleaners on brass or other metallic finish handles.
14
If your Pella ® door includes a solid brass handle, the brass is polished and sealed with a clear coating by the manufacturer. Should the finish be accidentally damaged by an abrasive or sharp object, it will succumb to a natural oxidation process that occurs when the elements contact unprotected brass. Brass has an enduring quality, in that it can be refurbished to its original polished finish again and again by using a quality brass polish and a soft cloth. Do not clean the bottom expander in this manner - see door cleaning above.
1. Remove the hardware from the door so the finish of the door will not be affected. See the hardware instructions for removal. NOTE: you may be able to leave the hardware in place on the door when polishing the handle only – make certain to
completely mask off all areas around the handle before starting. If polishing the key cylinder, protect the internal mechanism
by covering the opening with tape.
2. Use a quality brass polish or cleaner to clean the brass - follow the product’s directions and cautions. Note: Firm rubbing may
be necessary to loosen the coating on the brass.
3. Reseal the brass per instructions below.
a. Use the properties from the brass polish you used to clean the brass. (Easiest method, but requires more frequent polishing.)
b. Apply a high quality, non-abrasive, polymer-based automobile wax to seal the surface.
c. Apply a new clear coat with a clear lacquer spray - follow the product’s directions. (Most difficult, but lasts the longest.)
PLEASE NOTE: If you removed the hardware from the door, lubricate any internal workings with a spray lubricant. Re-install the hardware on the door. See the hardware instructions for installation.
Troubleshooting Guide
If you have a question that you do not see listed here, or have not been able to resolve through your Pella ® Owner’s Manual and Installation Guide, call one of our customer service representatives toll-free at 1-800-374-4758.
Common Questions Probable Causes Suggested Solutions
Door does not open or close properly.
Entryway framing is out of square/plumb or frame is warped
1. Verify the entryway framing and shim as necessary. [See Page 2]
Closer(s) out of position or adjustment.
Handle does not latch properly.
Water between the storm door and entry door.
Bottom Expander is out of position.
Drip Cap is out of position.
Hinges are binding
Latch not hitting trim plate
Closer is out of position
Bottom Sweep is making a tight seal against the door sill
1. Remove the adjustment screw from the closer(s), cycle the door a few times, then replace the screw. [See Page 10, Step 39]
2. Adjust the position of the closer door bracket until the door operates properly. [see
Page 10, Step 37]
3. If switching from glass to screen, vary the closer speed for proper operation. [see page
10, Step 39]
1. Verify the expander is centered on the door
– adjust if necessary. [See Page 4]
2. Verify the expander is not too low - adjust as necessary. [See Page 8, Step 25]
3. Verify sweep length is no more than 1/8” past expander edges. Trim as necessary.
1. Verify drip cap is centered and aligned in the opening - adjust as necessary. [See Page 5,
Step 12, Page 6, Step 13]
1. Verify mounting frame screws are not over tightened - back off screws slightly. [See Page
6, Step 13]
2. Verify entryway framing is not twisted or warped - shim or modify as necessary.
3. Verify hinge mounting frame is not twisted or bent - replace if necessary.
1. Adjust the trim plate until the latch catches.
[See separate hardware instruction]
1. See “Closer(s) out of position" in the “Door does not open or close properly" question above.
1. Open the storm door and notch up to 1/2-in off the ends of the black vinyl sweep.
15
Pella
®
Storm Doors Limited Warranty
Congratulations on choosing a Pella storm door to protect and beautify your home. This superior quality door has been designed to give you years of trouble-free service, and you are protected by this limited warranty:
Pella warrants to the ORIGINAL HOMEOWNER PURCHASER of this storm door that it will, without charge to the purchaser, provide parts or exchange, at its option, any door determined to be defective in material or workmanship for 20 years after the purchase date. The purchaser will be responsible for transportation charges. Should the door be determined to be defective in material or workmanship AFTER 20 years from the purchase date, the original purchaser may buy one new Pella storm door at 50% of the then- current manufacturer’s suggested list price for as long as the original purchaser owns the home on which the door was installed. The purchase must be made directly from the factory, and all transportation charges are the responsibility of the purchaser.
Should the door be determined to be defective and the purchaser incurs a reinstallation cost within three years of the purchase date, he or she may be reimbursed for these costs up to a maximum of $25.00, upon furnishing a copy of the invoice for the reinstallation costs.
As a condition of this warranty, it is required that the door be used for residential use only in an owner-occupied home, that it be installed properly as an operating door according to manufacturer’s instructions, and that it not be altered in any way. For multi-unit housing applications, ask your dealer for a copy of the appropriate warranty or phone Pella’s Customer Service Department at the phone number listed below. This warranty is not transferable.
To make a claim under this warranty, you should: a) Call our Customer Service Department at 1-888-646-5354 or write to Pella Warranty Service; 2333 Eastbrook Drive; Brookings, SD 57006 USA.
b) Furnish the original or a copy of the sales receipt or other documents showing the original purchase date and that you are the original purchaser of this door.
Exchange is limited to supplying a replacement door of comparable size, style, and color and does not include any cost of removal or installation except as noted above.
The warranty on the latch set and air closer is one year, and any labor charges are not covered. This warranty excludes all damage to glass and screen. This warranty does not cover problems caused by improper storage, handling, installation, use, modification, or maintenance, by Acts of God or by accidents, including accidental glass breakage. It does not apply to normal wear or discoloration of finish; finish problems caused by mechanical damage or abrasion; normal effects of sun and weather, including acid rain, salt spray, or other corrosive elements; damage caused by severe wind; or damage caused by customer abuse or neglect. Oil-Rubbed Bronze is a living finish that will develop its own unique patina with use and is not covered under the Lifetime Finish Guarantee. Bright Brass, Antique Brass, Brushed Brass and
Satin Nickel hardware is guaranteed not to tarnish and carries a lifetime finish warranty for as long as the purchaser owns their home.
THIS WARRANTY EXCLUDES ALL INCIDENTAL AND CONSEQUENTIAL DAMAGES. Nothing in this document shall give rise to or extend the period of any warranties implied under state or provincial law, and no implied warranty shall extend beyond the periods covered by this written warranty. Neither Pella Corporation nor any seller of Pella products will be responsible for incidental or consequential damages which may result from a product defect or malfunction. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may have additional rights which vary from state to state. Effective 7/2006.
© 2015
16
