seeTouch

TM

B&O

®

Keypads

15 V 65 mA

NEC

®

Class 2; IEC PELV

STBO-4SN STBO-4SI

STBO-4SIRN STBO-4SIRI

Overview

The STBO-4SIRN, -4SIRI, -4SI and -4SN are for use with HomeWorks

® systems. The keypad buttons are programmed using the HomeWorks

Software. The STBO-4SIRI and -4SIRN have an integrated IR receiver (on button 5 - no indicator

LED) that is compatible with the Bang & Olufsen

®

(B&O

®

) Beo4

®

IR Remote Control. The IR receiver accesses buttons 1-5, 23 and 24. The IR receiver can also receive commands from Beo4 buttons not available on the seeTouch

®

B&O Keypads, such as , , STOP

Up to 32 keypads, each with a unique address, can be connected to each keypad link on a

HomeWorks 4 Series or 8 Series P5 Processor.

Each keypad counts as 16 LEDs. A maximum of

350 keypad LEDs can be connected per 8 Series

P5 Processor, and a maximum of 150 keypad

LEDs can be connected per 4 Series P5

Processor. To add LED capacity, refer to the section about the Auxiliary Power Supplies in the

HomeWorks Technical Reference Guide (P/N 360-

963; in Europe, 360-963/EA).

Important Notes

, and

Button Function Chart (page 7).

GO . Refer to

Codes: Install in accordance with all local and national electrical codes.

WARNING: To avoid the risk of personal injury or property damage, these controls must not be used to control equipment which is not visible from every control location.

They must also not be used to control equipment which could create hazardous situations such as entrapment if operated accidentally. Examples of such equipment which must not be operated by

2 these controls include (but are not limited to) motorized gates, garage doors, industrial doors, microwave ovens, heating pads, etc. It is the installer’s responsibility to ensure that the equipment being controlled is visible from every control location and that only suitable equipment is connected to these controls.

Environment: Ambient operating temperature:

0 °C to 40 °C (32 °F to 104 °F), 0-90% humidity, non-condensing. Indoor use only.

Cleaning: To clean, wipe with a clean damp cloth.

DO NOT use any chemical cleaning solutions.

Wallboxes: seeTouch B&O keypads may be mounted in standard U.S. wallboxes (or in Lutron

Wallbox P/N 241-218, purchased separately). See

Mounting Diagram (page 4).

Keypad Wiring: Keypad wiring may be in a daisychain, star, or T-tap configuration. Each home run on a link may be up to 305 m (1 000 ft) and may contain up to 10 keypad devices. The total length of wire on that link (all home runs) may be up to

1 220 m (4 000 ft). Up to 32 keypad devices may be placed on each processor link configured as a keypad link in the HomeWorks Software. An external power supply may be required depending on the total current draw of all keypad devices on the processor.

Location: For best performance, do not locate keypad directly facing a plasma television. Plasma televisions interfere with all IR devices.

Installation

1. Disconnect power to the keypads by turning off all circuit breakers connected to the

HomeWorks

® processor or keypad link auxiliary power supply.

WARNING: To avoid the risk of electric shock, locate and lock supply breakers in the OFF position before wiring to terminal blocks.

Wiring with power on can result in serious injury.

2. Address keypads. Assign a unique address to each keypad using the DIP switch on the front of the keypad. See Keypad Addressing (page

5) for DIP switch location and DIP switch settings. Be sure to record the address for future programming purposes.

3. Strip insulation from wires to 10 mm (3/8 in).

Each terminal will accept one or two 1,0 mm 2

(18 AWG) wires.

4. Connect wiring to terminal block as shown in

Wiring Diagram (page 6).

5. Mount keypad as shown in Mounting Diagram

(below). Do not over-tighten mounting screws.

6. Restore power to the HomeWorks processor and keypad link auxiliary power supply (if used).

Mounting Diagram

Mounting

Screws Button Kit

Faceplate

Adapter (4SN model shown)

U.S. Backbox

63,5 mm (2 1 /

2 in) deep

Lutron Wallbox

P/N 241-218 Keypad

3

Faceplate (NI model shown)

Keypad Rear View

MUX

MUX

+15 V

COM

Class 2/PELV wiring connections to

HomeWorks ® processor or other keypads.

Keypad Addressing

Keypad Front View

(faceplate removed)

DIP switches 1-5 for setting address, DIP switches 6-10 do not affect keypad address.

DIP Switches

Set DIP switches 1-5 to give the keypad a unique HomeWorks system address from 1 to 32. DIP switches 6 through 10 do not affect the keypad address and should be always set in the up (on) position.

Address

1

#

ON

Switch

Settings

1 2 3 4 5 6 7

ON

2

1 2 3 4 5 6 7

ON

3

1 2 3 4 5 6 7

ON

4

1 2 3 4 5 6 7

ON

5

1 2 3 4 5 6 7

ON

6

1 2 3 4 5 6 7

ON

7

1 2 3 4 5 6 7

ON

8

1 2 3 4 5 6 7

Address

#

9

ON

Switch

Settings

1 2 3 4 5 6 7

ON

10

1 2 3 4 5 6 7

ON

11

1 2 3 4 5 6 7

ON

12

1 2 3 4 5 6 7

ON

13

1 2 3 4 5 6 7

ON

14

1 2 3 4 5 6 7

ON

15

1 2 3 4 5 6 7

ON

16

1 2 3 4 5 6 7

Address

#

17

ON

Switch

Settings

1 2 3 4 5 6 7

ON

18

1 2 3 4 5 6 7

ON

19

1 2 3 4 5 6 7

ON

20

1 2 3 4 5 6 7

ON

21

1 2 3 4 5 6 7

ON

22

1 2 3 4 5 6 7

ON

23

1 2 3 4 5 6 7

ON

24

1 2 3 4 5 6 7

Example: Setting Switch #1 ON.

UP (ON)

DOWN (OFF)

Address

#

25

ON

Switch

Settings

1 2 3 4 5 6 7

ON

26

1 2 3 4 5 6 7

ON

27

1 2 3 4 5 6 7

ON

28

1 2 3 4 5 6 7

ON

29

1 2 3 4 5 6 7

ON

30

1 2 3 4 5 6 7

ON

31

1 2 3 4 5 6 7

ON

32

1 2 3 4 5 6 7

4

Wiring Diagram

HomeWorks

®

P5 Processor

(8 Series

TM shown)

HomeWorks keypad link

Pins 1 & 2 - 1 pair 1,0 mm 2 (18 AWG) for power

Pins 3 & 4 - 1 pair 0,5 mm 2 to 1,0 mm 2 (22 AWG to

18 AWG) twisted/shielded for data

Button Function

(HWBO-4SE-IR and HWBO-8SE-IR only)

Beo4

®

IR Remote Control Beo4 Button Detail

LIGHT Button

Used for initiating all IR commands to

HomeWorks B&O

®

Keypad

1-9 Buttons

Used to select additional 9 scenes

0 Button

Used to select OFF Scene

Color Buttons, GO Button, ,

, and Buttons

See Beo4 Button Detail

STOP Button

Used to stop Raise/Lower of shades

,

Color Buttons

Correspond to color buttons on

HomeWorks B&O Keypad

GO Button

Used to select additional scene and Buttons

Used to control shades

Green Yellow and Buttons

Used to Raise/Lower lights in current scene

Red Blue

Keypad Button Detail (STBO-4SIRI shown)

Red

Green

3

4

1

2

Yellow

5

Blue

23 24

5

0

Button Function Chart

Beo4 Button*

Red button

Green button

Yellow button

Blue button

GO (Play)

1 - 9

STOP

HomeWorks

®

Keypad Button

Btn 1: Red (Actual keypad button)

Btn 2: Green (Actual keypad button)

Btn 3: Yellow (Actual keypad button)

Btn 4: Blue (Actual keypad button)

Btn 5: (Actual keypad button)

Btn 10

Btns 11 - 19

Btn 21

Function

Programmable - Defaults to single action scene (can be programmed to control any zone/scene)

Programmable - Defaults to single action scene (can be programmed to control any zone/scene)

Programmable - Defaults to single action scene (can be programmed to control any zone/scene)

Programmable - Defaults to single action scene (can be programmed to control any zone/scene)

Programmable - Defaults to single action scene (can be programmed to control any zone/scene)

Programmable - Defaults to single action scene (can be programmed to control any zone/scene)

Programmable - Defaults to single action scene (can be programmed to control any zone/scene)

Used to control shades.

May also be programmed to control lights.

Btn 22

Btn 20

Used to control shades.

May also be programmed to control lights.

Used to stop raise/lower of shades.

May also be programmed to control lights.

Btn 24: (Actual keypad button) Master Raise.

Possibly single scene raise (any specified zone/scene).

Btn 23: (Actual keypad button) Master Lower.

Possibly single scene lower (any specified zone/scene).

* Light Button must be pressed first before pressing any other button.

6

Troubleshooting Guide

Keypad is working properly when LEDs light up and loads respond as buttons are pressed.

Symptom

LEDs don't light up.

Cause and Action

Power is not present at keypad.

• Make sure HomeWorks

®

Processor is powered up.

• Check for 15 V between pins 1 & 2 on the keypad connector.

• Remove connector from back of keypad, check connections and replace.

LEDs cycle from top to bottom sequentially.

LEDs light when button is pressed, but the system response isn't correct.

No response from the keypad when an IR remote button is pressed.

Keypad is properly powered but is not communicating with the processor.

• Verify that the processor is running.

• Check that keypad wires 3 & 4 are properly connected.

• Check that keypad link is plugged into correct connector at processor.

• Verify that link is configured for HomeWorks keypads in the HomeWorks

Software.

Keypad improperly addressed.

• Check keypad for proper address. See Keypad Addressing (page 5).

Keypad improperly programmed.

• Check system programming.

B&O

®

Beo4

®

IR Remote is in the incorrect mode.

• Press the “Light” Button before initiating any button presses from the remote.

Batteries in IR remote are weak

• Replace batteries in remote.

Keypad improperly programmed.

• Refer to Button Function Chart (page 7) and check system programming.

Interference from plasma television.

• Move or turn off plasma television.

7

Technical Assistance

If you have questions concerning the installation or operation of this product, call Lutron’s European

Headquarters . Please provide exact model number when calling.

European Headquarters

Lutron EA LTD

Lutron House

6 Sovereign Close

Wapping

London, E1 9HW England

FREEPHONE: 0800-282-107 (U.K.)

Tel:

Fax:

+44-(0)20-7702-0657

+44-(0)20-7480-6899

Lutron Electronics Co., Inc.

Made and printed in U.S.A.

P/N 043-225 Rev. A 1/09

8

LIMITED WARRANTY

(Valid in the European Union and Asia)

What This Warranty Covers

Lutron warrants each new Unit to be free from defects in materials or workmanship under conditions of normal use and specified ambient temperature when installed and operated in accordance with Lutron product specifications and applicable EU and local safety regulations.

What This Warranty Does Not Cover

This warranty does not cover:

1) Damage or improper operation determined by Lutron to be due to abuse, misuse, or accident, such as: a. Use of incorrect line voltages; b. Use of incorrect fuses or breakers; c. Failure to follow operating instructions provided by Lutron; d. Failure to maintain and operate equipment in accordance with applicable EU and local safety regulations; e. Failure to maintain equipment under specified ambient temperature; f.

Unauthorized or improper repairs or adjustments; g. Vandalism; and h. Fire, flood,

“Acts of God”, and other problems beyond the control of Lutron.

2) Labor costs to remove and reinstall electronic fixture packs and/or ballasts.

3) Components and equipment external to the Lutron Unit, such as: a. Lamps; b.

Ballasts, sockets, and fixtures; c. Wiring between ballasts and lamps; d. Building wiring; e. Other manufacturers’ equipment, such as: 1. Time clocks; 2. Audio-visual equipment; 3. Motion detectors; 4. Photosensors; 5. Driveway sensors; 6. Pressure pads; 7. Shades; and 8. Spas.

4) The cost of repairing or replacing property other than the warranted Unit.

What Lutron Will Do

To the extent permitted by law, Lutron will, at its option, repair or replace any Unit that is defective in materials or manufacture which, in Lutron’s opinion, has been properly installed, wired, insulated, used, and maintained. Lutron shall not be required to remove, install, or re-install any defective Unit. Credit will be granted against the purchase price for replacement parts according to the following schedule:

Number of Years from Date of

Installation

Up to 2

More than 2 but not more than 5

More than 5 but not more than 8

More than 8

Percentage of Cost of Replacement Parts

Credited by Lutron

100%

50%

25%

0%

Although every attempt is made to ensure that catalogue information is accurate and up-to-date, please check with Lutron EA before specifying or purchasing any unit to confirm availability, exact specifications, and suitability for your application.

This warranty does not affect the statutory rights of consumer purchasers of the unit.

This product is covered under one or more of the following patents and design registrations:

In the United States: D437,834; D441,723; D442,558.

In Canada: 1,332,625; 1,331,769.

In the United Kingdom: 0587878; 2221345B; 2251727B.

In Germany: 69314585.5; 3923022.8.

In France: 0587878.

In Italy: 0587878.

In Japan: 2,819,165; 3079477.

U.S. and foreign patents pending. Lutron, seeTouch, HomeWorks, the HomeWorks logo, and the sunburst logo are registered trademarks of Lutron Electronics Co., Inc.

NEC is a registered trademark of the National Fire Protection Association, Quincy,

Massachusetts. Bang & Olufsen, B&O, and Beo4 are registered trademarks of Bang

& Olufsen, Struer, Denmark.

© 2009 Lutron Electronics Co., Inc.