SportsArt N933 Owner Manual
Add to My manuals26 Pages
SportsArt N933 is a high-quality, full commercial use, independent Pec Deck machine designed and built for optimum safety and years of reliable performance. It is constructed of high-quality materials and was made for full commercial use.
advertisement
N933 OWNER’S MANUAL CONTENTS
1. INTRODUCTION ........................................................................... 2
2. SAFETY PRECAUTIONS ............................................................. 3
3. LIST OF PARTS ............................................................................. 4
4. ASSEMBLE THE PRODUCT ......................................................... 6
STEP 1 Install the Foot Rest ..................................................................... 6
STEP 2 Install the Weight Stack Covers ..................................................... 7
STEP 3 Install the Cap Nut ..................................................................... 8
STEP 4 Secure the Unit .......................................................................... 9
STEP 5 Handle Position Adjustment Instructions
STEP 6 Seat Position Adjustment Instructions
STEP 7 Belt Tension Adjustment Instructions ............................................... 12
STEP 8 Minor Weight Stack Instructions
STEP 9 Unit Inspection
.......................................... 10
.............................................. 11
.................................................... 13
............................................................................14
5. OPERATE THE PRODUCT ............................................................. 15
OPERATION Safety Operating Area ........................................................... 15
OPERATION Exercising Instructions .......................................................... 16
6. MAINTENANCE ............................................................................... 17
MAINTENANCE Safety Precautions ......................................................... 17
MAINTENANCE Guide Rod Cleaning and Lubricating .................................. 18
MAINTENANCE Important Note ............................................................... 19
MAINTENANCE Schedule ..................................................................... 20
MAINTENANCE Task List ...................................................................... 21
MAINTENANCE Maintenance Log ............................................................ 22
7. CONSIGNES DE SÉCURITÉ IMPORTANTES ............................... 23
8. APPENDIXES ................................................................................. 24
APPENDIXES Exploded Diagram ............................................................ 24
1. INTRODUCTION
Congratulations on the purchase of a high quality SportsArt product, the N933
Independent Pec Deck machine. Constructed of high quality materials and designed for years of reliable performance, this product was made for full commercial use.
Before this product is assembled or operated, we recommend that you familiarize yourself with this manual. Understanding the correct assembly and operation of this product will help ensure that exercisers obtain their fitness goals safely and successfully.
1550mm (61 )
1397mm (55 )
2
2. SAFETY PRECAUTIONS
This product was designed and built for optimum safety. However certain precautions apply during the use of this product. Please note the following safety precautions:
• Please read the entire manual before assembly and operation. Make sure the product is installed and operated as instructed in this manual.
• Assemble and operate the product on a solid, level surface. Do not use outdoors or near water, including pools and saunas.
• Check the product before every use. Make sure all parts are assembled, and all fasteners are tightened. Do not use the product if it is disassembled in any way.
• Wear proper workout clothing. Do not wear loose clothing. Do not wear shoes with leather soles or high heels. Tie all long hair back. Do not go barefoot on this product.
• Keep away from moving parts. Moving parts may or may not stop immediately if an object becomes caught or impedes normal motion.
• Use this product only for its intended purpose as described in this manual.
• Be careful when mounting and dismounting the unit.
• Never operate this product if it has been damaged in any way. If it is not working properly, or has been dropped or damaged, contact a service technician for repairs.
• Do not use accessories or parts that are not specifically recommended by the manufacturer (SportsArt) . Such parts might cause injuries or cause the unit to fail and void the warranty. We will not be responsible for any safety issue that arises due to the misuse of accessories or parts. At the same time, we will terminate the warranty terms of this equipment.
• This product is not intended for use by persons (including children 12 or younger) with reduced physical, sensory, or mental capabilities, or by people who are otherwise deficient in product knowledge or experience. If such people use this product, they should be given training and be supervised at all times by someone responsible for their safety.
• Children ages 12 or younger should be supervised to ensure that they do not play on or near the product.
• Maintenance and repair must be performed by trained service personnel only. Improper maintenance would not only damage the machine, but also may present a danger to the exerciser.
• The user weight limit for this product is 227 kg (500 lb).
• Warning that any of the adjustment devices that could interfere with the user’s movement should not be left projecting.
CAUTION: If you feel any pain or any abnormal sensations, STOP YOUR
WORKOUT and consult your physician immediately. Work within your recommended exercise level. DO NOT work to exhaustion. Before beginning any exercise program, you should consult with your doctor. It is recommended that you undergo a complete physical examination.
Over exercise may result in serious injury or death. If you feel faint, stop exercising immediately.
*NOTE: Each machine provides a different resistance ratio of weight stack.
3
3. LIST OF PARTS
No.
Name
Assembly Parts
Qty. No.
Name Qty.
A1 Main Frame
A2 Foot Rest
1 A6 Dual 80 Oval Foot
1 A7 118 Oval Foot Cover A
1
1
A3 Weight Stack Front Cover 1 A8 118 Oval Foot Cover B 1
A4 Weight Stack Rear Cover 1 A9 U Clip 1
A5 Dual 80 Oval Foot Cover A 1 A10 Ground Fixing Bracket 1
4
No.
10 Push rivets
Components In the Hardware Kit
Name
L-shaped Allen wrench
L-shaped Allen wrench
Double open-end wrench
19 Cap nut
Qty.
Specification Notes
4
2 (M5)
1 (M6)
1 (8*17)
No.
20
21
Components on the Product
Name Specification
Mushroom head inner hex screw M8*L20
Spring washer M8
Flat washer
Mushroom top Phillips screw
(heat treatment)
Flat washer
D17*d8.3*t2
M5*0.8*L15
D13*d6*t1.0
Notes
5
4. ASSEMBLE THE PRODUCT
Follow instructions below to assemble this product. Note that in this manual
the words “left” and “right” are used to refer to the product and its parts. As
such, these designations correspond to the “left” and “right” sides of a person
in position to exercise on this product. Also, for brevity, the word “screws” or
“nuts” is used where washers and other hardware may be involved.
STEP 1 Install the Foot Rest
Follow steps (a) through (b) to install the foot rest.
(a). First, remove the screws (20) from the foot pedal frame (A2).
(b). Attach the foot rest (A2) onto the main frame (A1) and use screws (20)
to secure the assembly.
6
STEP 2 Install the Weight Stack Covers
(a). Attach both front and back weight stack covers (A3)(A4) onto the weight
stack frame (A1). (Note: before the attaching the front weight stack cover
(A3), make sure the inside hanger is hooked to the frame before securing
it to the weight stack frame.)
(b). Attach the oval foot covers (A5)(A6)(A7)(A8) onto the weight stack frame
(A1) legs. Align the ends before use push rivets (10) to secure the foot
covers together.
Note: If the holes don’t match up while installing the oval foot covers, change their direction and put them back in a new way. The cutout should face the inner side of the foot tube.
7
STEP 3 Install the Cap Nut
After completing the assembly, install the cap nut (19) as shown in the following figure.
Note: Make sure the cap nuts and screws are size-matching.
8
STEP 4 Secure the Unit
Please follow the instructions (a) through (c) to secure the unit and make sure it is firmly fixed to the floor when operating.
(a) Remove screws (21) from the ground fixing bracket (A10).
(b) Insert the U clip (A9) onto the machine (Make sure the U clip is in the
correct direction as shown below), and then secure the ground fixing
bracket (A10) with screws.
(c) Secure the ground fixing bracket to the floor with the ground fixing bolt,
nut and washer.
Note: The screw hole of ground fixing bracket is Ø9mm, make certain you use the suitable ground fixing bolt and drill the proper hole on the floor.
(a)
(b)
(c)
9
STEP 5 Handle Position Adjustment Instructions
Lift upward on lever until desired handle angle is achieved, and then release the lever to lock the handle in place.
10
STEP 6 Seat Position Adjustment Instructions
*Back angle adjustment: pull the lever (marked by arrow-A) out and move it
toward the left/right to adjust the back angle. If the desired angle is reached,
release the lever to lock in place.
*Seat height adjustment: pull the lever (marked by arrow-B) out to adjust the
seat height. Once you reach the desired height, release the lever to lock into
place.
* If the seat has not been used for a long time, or the height adjuster moves
unsmoothly, try pressing and holding down the seat several times before
adjusting seat height.
11
STEP 7 Belt Tension Adjustment Instructions
1. After finishing installation and the final positioning of the equipment,
perform the whole-machine-test to ensure it works properly.
2. If the belt tension is incorrect, perform the modification adjustment: First
loosen nut A then adjust nut B (as shown in the figure).
Note that if the belt is too long, adjust the nut down, and vice versa. Once
the belt reaches the desired position, tighten nut A to secure the belt
length.
Note: After adjusting the belt, the gap between nut A and B must be within
35mm(1.4”). If the gap still exceeds the 35mm limit, you need to perform
the following modifications:
A. Loosen the screws as pointed by the arrow-C, and adjust the belt to
the proper length.
B. Tighten the screws pointed by the arrow-C.
3. After finishing the above adjustments, perform the whole- machine -test
again to ensure the unit functions properly.
12
STEP 8 Minor Weight Stack Instructions
To adjust the minor weight stack, insert the upper pin to add 3.5Lbs/1.5kgs, or the lower pin to add 6.5Lbs/3kgs. When the minor weights are not in use, pull the pin to release the weight.
13
STEP 9 Unit Inspection
After completing the assembly or regular maintenance, please follow instructions (a) through (c) to inspect the unit. If the unit is disassembled or has been damaged in any way, it might cause injuries or cause the unit to fail.
(a) Make sure the unit is steady and is on a level surface. If not, make ad-
justments according to the instructions “Secure the Unit” in this manual.
(b) Make sure all parts are assembled and all fasteners are tightened.
(c) Please follow operating instructions to test operation and make sure that
the equipment is working properly. (Please refer to “Operate the Product”
in this manual.)
14
5. OPERATION THE PRODUCT
This section includes operational instructions.
OPERATION Safety Operating Area
(a) Safety clearance required is shown below. Do not allow access for peo-
ple to near this area when operating.
(b) Noise emission under load is higher than without load.
(c) Over exercise or improper workout position may result in serious injury.
(d) This equipment is intended to build chest muscles.
15
OPERATION Exercising Instructions
(a) Select the appropriate weight stacks according to your recommended
exercise level.
(b) Adjust the seat height and seat angle to the most comfortable position
and make sure the knob is engaged to secure the position.
(c) Perform the exercise in a controlled manner. Inhale when pushing up
against resistance and exhale when returning to original position.
* Always workout at a level that is tolerable, to stay in the proper training
zone for your body. DO NOT work to exhaustion.
* Use equipment ONLY under the supervision of trained and qualified ins-
tructors for safety reasons.
* Please follow operating instructions on the product sticker to test opera-
tion and make sure the equipment is working properly.
16
6. MAINTENANCE
This section covers maintenance topics and includes a maintenance schedule, task list, and log.
MAINTENANCE Safety Precautions
● Please follow standard safety precautions when servicing on this pro- duct.
● Do NOT use a damp towel to clean the product and do perform the following maintenances.
● Do NOT use cleaners with alcohol, ammonia, or other damaging chemicals.The use of such chemicals can damage the product and void the warranty. Never spray or pour any liquid directly onto the product. Doing so can damage components and void the warranty.
● Use a clean, lint-free towel, dampened with a mixture of Simple Green®allpurpose cleaner, to thoroughly clean the handlebar and the console.
● This product has moving parts that can be hazardous. Exercise cautionwhen maintaining, operating, or moving this product.
● Do not use accessories or parts that are not specifically recommend edby the manufacturer (SportsArt) . Such parts might cause injuries or cause the unit to fail and void the warranty. We will not be responsible for anysafety issue that arises due to the misuse of accessories or parts.
At the same time, we will terminate the warranty terms of this equipment.
● Maintenance and repair must be performed by trained service personnel only. Improper maintenance would not only damage the machine, but also may present a danger to the exerciser.
● Keep this product out of use until maintenance is completed.
17
MAINTENANCE Guide Rod Cleaning and Lubricating
1. Please clean and lubricate the guide rod once a week.
(a) Use a clean, lint-free towel to apply the lubricant onto the guide rods.
(b) Test the weight stacks on the guide rod and make sure the weight
stacks move smoothly.
(c) Repeat step (a) and (b) 2-3 times.
2. Ensure proper settling of the belt tension after maintenance.
18
MAINTENANCE Important Note
1. Once the machine belt reaches the warranty period, replace the belt im
mediately.
2. Safety belt inspection: After a one-year period of usage, check the belt
weekly for standard inspection. (The actual frequency of inspection de
pends upon the frequency of use)
Refer to the figure below for belt inspection: (A) the belt, (B) the belt ex
tension.
Note: If you have a damaged or worn belt, stop using the equipment and replace the belt immediately.
19
MAINTENANCE Schedule
Area Day Week Month Quarter Year
1 Exterior ●
2 Screws
3 Testing
4 Cushions
5 Belt
6 Guide Rod
7 Seat Tube
●
●
●
●
●
●
Notes
Clean.
Inspect and secure loose parts
Use performance testing to make sure the machine works as expected.
Use a cloth moistened with water then wrung well, and wipe the cushions gently
Check for damage or wear. If so, replace it with a new one
Clean and lubricate
Clean and lubricate
20
MAINTENANCE Task List
tLike cars, fitness products require maintenance. Regular maintenance extends product life, and failure to maintain products can void the manufacturer’s warranty. Copy the maintenance log sheet, and record maintenance work for each fitness product.
Daily tasks
1. Use a clean, lint-free towel to wipe down the product exterior.
2. Inspect all screws. Secure if necessary.
3. Make sure the machine is working properly.
4. Wipe cushions clean with a damp cloth.
Weekly tasks
1. Check the belt for damage or tear.
2. Clean and lubricate guide rods.
3. Clean and lubricate seat tube.
Caution
●Please follow standard safety precautions when working on this product.
●Do NOT use cleaners with alcohol, ammonia, or other damaging chemi-
cals. The use of such chemicals can damage the product and void the war-
ranty. Never spray or pour any liquid directly onto the product. Doing so can
damage components and void the warranty.Never spray or pour any liquid
directly onto the product. Doing so can damage components and void the
warranty.
21
MAINTENANCE Maintenance Log
Facility:____________________ Supervisor: ____________________
Product model number:_______ Serial number:__________________
Start date:__________________ End date:______________________
Week 15-21 Week 22-28 Daily Tasks
Completed
Daily Tasks
Completed
Week 1-7
Week 29-35
Week 8-14
Week 36-42 Week 43-49 Week 50-52
Weekly Tasks
Completed
Weekly Tasks
Completed
Week 1-7
Week 29-35
Week 8-14
Week 36-42
Week 15-21 Week 22-28
Week 43-49 Week 50-52
Monthly Tasks 1
Completed
2 3 4 5 6 7 8 9 10 11 12
Quarterly Tasks
Completed
Quarter 1 Quarter 2 Quarter 3 Quarter 4
Yearly Tasks
Completed
Year 1
Notes:________________________________________________
__________________________________________________
22
7. CONSIGNES DE SÉCURITÉ IMPORTANTES
Le produit SportsArt a été conçu et fabriqué afin d’assurer une sécurité optimale.
Cependant certaines précautions s’appliquent chaque fois que vous utilisez votre produit.
• Lisez entièrement le manuel avant l’assemblage et l’utilisation. Veuillez aussi noter les consignes de sécurité suivantes:
• Veuillez lire attentivement les instructions et installer le produit selon les instructions.
• Assemblez et faites fonctionner le produit sur une surface solide et plane; NE
PAS l’utiliser à l’extérieur ou près de l’eau.
• En aucun cas, ne laissez des enfants à proximité ou sur le produit.
• Vérifiez le tapis de course avant chaque utilisation. Assurez-vous que toutes les pièces sont assemblées et que tous les éléments de fixation sont serrés. NE PAS utiliser le produit si l’appareil est démonté de quelque façon.
• Gardez vos mains loin des pièces mobiles.
• Portez des vêtements d’entraînement appropriés; NE PORTEZ PAS de vêtements amples. NE PORTEZ PAS de chaussures à semelles en cuir ou à talons hauts. Attachez les cheveux longs.
• Soyez prudent lors du montage et démontage de l’appareil.
• NE PAS utiliser d’accessoire non spécifiquement recommandé par le fabricant.
Car cela pourraient provoquer des blessures ou entraîner une panne de l’appareil.
• Débranchez l’appareil de la prise avant l’entretien ou la suppression de toute pièce.
• Une surveillance étroite est nécessaire quand de produit est utilisé par ou à proximité d’enfants, de malades ou de personnes handicapées.
• Utilisez ce product uniquement pour l’usage prévu dans ce manuel.
• La limite de poids de l’utilisateur pour le produit est de 227 kg, 500 lb.
• Ce produit n’est pas destiné à être utilisé par des personnes (y compris des enfants) dont les capacités physiques, sensorielles ou mentales sont réduites ou qui ne disposent pas de l’expérience ou du savoir nécessaires, sauf si celles-ci ont au préalable été formées eu égard à l’utilisation de produit par une personne responsable de leur sécurité.
• Les enfants doivent être encadrés afin d’empêcher qu’ils ne jouent avec le produit.
• Ce produit n’est pas destiné à être utilisé par des personnes (y compris des enfants) dont les capacités physiques, sensorielles ou mentales sont réduites ou qui ne disposent pas de l’expérience ou du savoir nécessaires, sauf si celles-ci ont au préalable été formées eu égard à l’utilisation de ce produit par une personne responsable de leur sécurité.
• Les enfants doivent être encadrés afin d’empêcher qu’ils ne jouent avec le produit.
ATTENTION
Si vous ressentez une douleur ou si vous avez une sensation anormale, AR-
RÊTEZ VOTRE ENTRAÎNEMENT et consultez immédiatement votre médecin.
Entraînez-vous à votre niveau d’exercice recommandé. NE PAS s’entraîner jusqu’à l’épuisement. Avant de commencer un programme d’exercice, vous devriez consulter votre médecin. Il est recommandé de faire un examen physique complet.
Dans ce manuel, les mots “gauche” et “droit” sont utilisés en référence aux pièces et au produit. Comme tels, les mots “gauche” et “droit” font respectivement référence aux côtés gauche et droit de l’exerciseur. De même pour plus de concision, le mot «vis» est utilisé dans certains cas où des rondelles, des vis et autres matériels sont associés.
23
8. APPENDIXES
APPENDIXES Exploded Diagram
Note: We reserve the right to revise the following diagrams at any time without notice or obligation to notify any person of such revisions or changes.
Please visit our official website www.gosportsart.com for the latest version.
24
APPENDIXES Exploded Diagram
25
Your Authorized Distributor
26
advertisement
Key Features
- Full commercial use
- High-quality materials
- Optimum safety
- Years of reliable performance
Related manuals
Frequently Answers and Questions
What are the safety precautions for using this product?
What is the user weight limit for this product?
How do I adjust the handle position?
How do I adjust the seat position?
How do I adjust the belt tension?
advertisement