MasterForce FlexPower 267-3293 Operator's Manual

Cordless String Trimmer

267-3293

OPERATOR’S MANUAL

CAUTION: To Reduce the Risk of Injury, User Must

Read and Understand the Operator’s Manual. Save These

Instructions For Future Reference.

For questions / comments, technical assistance or repair parts –

Please Call Toll Free: 1-866-917-4374 (M-F 8:30am-5:00pm EST).

TABLE OF CONTENTS

Safety Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 2

Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 3

Overview/Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 7

Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 8

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 11

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 16

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 17

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 18

SAFETY SYMBOLS

Some of these following symbols may be used on this tool. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and more safely.

Symbol Name

V Volts

A Amperes

Hz n o

Hertz

No-load speed

RPM Per minute

� Direct current

Designation / Explanation

Voltage

Current

Frequency (cycles per second)

Rotational speed at no load

Revolutions, strokes, surface speed orbits, etc., per minute

Type or characteristic of current

WARNING:

To ensure safety and reliability, all repairs should be performed by a qualified service technician.

Page 2

SAFETY INSTRUCTIONS

The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and the explanations with them, deserve your careful attention and understanding. The symbol warnings do not, by themselves, eliminate any danger. The instructions and warnings they give are no substitutes for proper accident prevention measures.

WARNING:

Be sure to read and understand all safety instructions in this manual, including all safety alert symbols such as “DANGER”, “WARNING” and “CAUTION” before using this tool. Failure to follow all instructions listed below may result in electric shock, fire, and/or serious personal injury.

SYMBOL MEANING

SAFETY ALERT SYMBOL: Indicates DANGER, WARNING, OR CAUTION.

May be used in conjunction with other symbols or pictographs.

DANGER:

Indicates an imminently hazardous situation, which, if not avoided, will result in death or serious injury.

WARNING:

Indicates a potentially hazardous situation, which, if not avoided, could result in death or serious injury.

CAUTION:

Indicates a potentially hazardous situation, which, if not avoided, could result in minor or moderate injury.

NOTICE:

(Without Safety Alert Symbol) Indicates a situation that may result in property damage.

SAVE THESE INSTRUCTIONS!

Page 3

SAFETY INSTRUCTIONS

IMPORTANT SAFETY

INSTRUCTIONS

WARNING:

When using electric trimmers, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and personal injury, including the following:

READ ALL INSTRUCTIONS

DANGER:

Do not rely on the tool’s insulation against electric shock. To reduce the risk of electrocution, never operate the tool in the vicinity of any wires or cables which may carry electric current.

CAUTION:

Wear appropriate personal hearing protection during use.

Under some conditions and durations of use, noise from this product may contribute to hearing loss.

1. Avoid dangerous environments.

Don’t use appliances in damp or wet location.

2. Don’t use in rain.

3. Keep children away. All visitors should be kept at least 100 ft. away from work area.

4. Dress properly.

Do not wear loose clothing or jewelry. They can be caught in moving parts. Use of rubber gloves and substantial footwear is recommended when working outdoors. Wear protective hair covering to contain long hair.

5. Use safety glasses. Always use face or dust mask if operation is dusty.

6. Use the right appliance. Do not use the tool for any job except that for which it is intended.

7. Avoid unintentional starting. Don’t carry the trimmer with your finger on the trigger.

Always remove the battery pack whenever leaving the trimmer unattended.

8. Don’t force the appliance.

It will do the job better and with less likelihood of a risk of injury at the rate for which it was designed.

9. Don’t overreach.

Keep proper footing and balance at all times.

10. Stay alert. Watch what you are doing.

Use common sense. Do not operate the appliance when you are tired.

11. Keep guards in place and in working order.

12. Keep hands and feet away from the cutting area.

13. Store idle appliances indoors.

When not in use, the appliances should be stored indoors in a dry and high or locked-up place with the battery pack removed out of reach of children.

14. Maintain appliance with care.

Keep cutting edge sharp and clean for best performance and to reduce the risk of injury. Follow instructions for lubricating and changing accessories. Keep handles dry, clean, and free from oil and grease.

15. Check damaged parts. Before further use of the appliance trimmer, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function.

Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting, and any other condition that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced by an authorized service center unless indicated elsewhere in this manual.

16. Do not charge the battery pack in rain, or in wet locations.

17. Remove or disconnect battery pack before servicing, cleaning or removing material from the trimmer.

18. Use only with the battery packs and chargers listed below:

Battery pack

252-8024, 252-8029,

252-8030, 252-8031,

252-8032, 252-8033,

252-8034, 252-8035

Charger

252-8025,

252-8036,

252-8037,

252-8044

19. Do not dispose of the battery in a fire. The cells may explode.

Check with local codes for possible special disposal instructions.

Page 4

SAFETY INSTRUCTIONS

20. Do not open or mutilate the battery.

Released electrolyte is corrosive and may cause damage to the eyes or skin.

It may be toxic if swallowed.

21. Exercise care in handling batteries in order not to short the battery with conducting materials such as rings, bracelets, and keys. The battery or conductor may overheat and cause burns.

22. Do not operate the trimmer while under the influence of alcohol or drugs.

23. Clear the area to be cut before each use. Remove all objects such as rocks, broken glass, nails, wire, or string that can be thrown or become entangled in the cutting attachment.

Make sure that other persons and pets are at least 100 ft. (30.5m) away.

30. A loose head may vibrate, crack, break or come off the trimmer, which may result in serious or fatal injury. Make sure that the cutting attachment is properly fixed in position.

If the head loosens after fixing it in position, replace it immediately.

31. Never use a trimmer with a loose cutting attachment.

32. Replace a cracked, damaged or wornout cutting head immediately, even if damage is limited to superficial cracks.

Such attachments may shatter at high speed and cause serious or fatal injury.

with both hands on the handles, while operating. Wrap your fingers and thumbs around the handles.

25. To reduce the risk of injury from loss of control, never work on a ladder or on any other insecure support. Never hold the cutting attachment above waist height.

26. Do not operate the trimmer in gaseous or explosive atmospheres. Motors in these appliances normally spark, and the sparks might ignite fumes.

27. Wear heavy long pants, long sleeves, boots, and gloves.

Avoid loose garments or jewelry that could get caught in moving parts of the machine or its motor.

regular short intervals during operation, or immediately if there is a noticeable change in cutting behavior.

34. When replacing the cutting line, use triangle-shaped twisted nylon cutting line with a size that does not exceed

0.08 in. (2.0 mm); using heavier lines than recommended by the manufacturer increases the load on the motor and reduces its operating speed. This results in overheating and damage to the trimmer.

35. To reduce the risk of serious injury, never use wire or metal-reinforced line or other material in place of the nylon cutting lines. Pieces of wire could break off and be thrown at high speed toward the operator or bystanders.

a foreign object with the trimmer or it becomes entangled, stop the tool immediately, check for damage and have any damage repaired before further operation is attempted.

Do not operate with a broken guard or spool.

29. If the equipment should start to vibrate abnormally, stop the motor and check immediately for the cause. Vibration is generally a warning of trouble.

replacement parts.

Use of any other accessory or attachment which is not recommended for use with this tool may increase the risk of injury.

37. Do not wash with a hose; avoid getting water in motor and electrical connections.

38. Save these instructions. Refer to them frequently and use them to instruct others who may use this tool.

If you lend this tool to someone else, also lend these instructions to them to prevent misuse of the product and possible injury.

Page 5

DANGER:

People with electronic devices, such as pacemakers, should consult their physician(s) before using this product. Operation of electrical equipment in close proximity to a heart pacemaker could cause interference or failure of the pacemaker.

WARNING:

• Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the state of California to cause cancer, birth defects, or other reproductive harm. Some examples of these chemicals are:

–Lead from lead-based paints.

–Crystalline silica from bricks, cement, and other masonry products.

–Arsenic and chromium from chemicallytreated lumber.

• Your risk from these exposures varies, depending upon how often you do this type of work. To reduce your exposure to these chemicals:

–Work in a well-ventilated area.

–Work with approved safety equipment, such as dust masks that are specially designed to filter out microscopic particles.

–Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling, and other construction activities. Wear protective clothing and wash exposed areas with soap and water. Allowing dust to get into your mouth or eyes or to lie on the skin may promote absorption of harmful chemicals.

SAVE THESE INSTRUCTIONS!

Page 6

OVERVIEW

Trimmer Head

Front-assist Handle

Rear Handle

Lock-off Button

Variable-speed

Trigger Switch

Trimmer Shaft

Hinge

Rated Voltage

No-load Speed

Cutting-line Type

Cutting Width

Guard

Bump Knob

SPECIFICATIONS

20 V d.c.

5800-7000 RPM

0.08 in. twisted nylon line

12 in.

Page 7

ASSEMBLY

WARNING:

If any part is broken or missing, DO NOT attach the battery pack or operate the tool until the broken or missing part is replaced. Failure to do so could result in possible serious injury.

WARNING:

Do not attempt to modify this tool or create accessories not recommended for use with this tool. Any such alteration or modification is misuse and could result in a hazardous condition leading to possible serious injury.

WARNING:

Your tool should never be connected to the battery pack when you are assembling parts, making adjustments, installing or removing blades, cleaning, or when it is not in use. Disconnecting the tool will prevent accidental starting, which could cause serious personal injury.

CONTENTS

Cordless string trimmer, front-assist handle, guard, screw knob, bolt, hexagon screw (×2), screw with washer (×2) for the guard, and instruction manual.

UNPACKING

1. Carefully remove the string trimmer and any accessories from the carton. Make sure that all items listed in the packing list are included.

2. Inspect the string trimmer carefully to make sure that no breakage or damage occurred during shipping.

3. Do not discard the packing material until you have carefully inspected and satisfactorily operated the string trimmer.

ASSEMBLY

UNFOLD THE SHAFT

WARNING:

Always take care that the cable and your hands are not pinched by the shaft when you are unfolding or folding the string trimmer. Do not attempt to start the trimmer until the shaft has been locked.

1. Remove the battery pack from the trimmer.

2. Put the trimmer on the ground and carefully unfold the shaft. Make sure that the cable is inside the shaft so that it will not be pinched when closing the joints (Fig.1).

3. Use a hex wrench (not included) to lock the shaft with the hexagon screws supplied

(Fig.2).

CAUTION:

If you want to fold the shaft again, remove two hexagon screws near the rear handle side.

FIG. 1

Page 8

FIG. 2

FIG. 3

ASSEMBLY

Hexagon Screws

2. Lift the trimmer head and face it upward; align the groove on the bottom of the guard with the raised portion on the base of the trimmer head, and then slide the guard onto the base (Fig 3).

3. Make sure that the two mounting holes in the guard are aligned with the two assembly holes in the base of the shaft. Insert a screw into each washer, and then lock the guard in place by tightening the two screws with a screwdriver (not included) (Fig 4).

FIG. 4

Guard

Screw

Washer

Trimmer Head

MOUTING THE FRONT-ASSIST

HANDLE (FIG.5)

MOUTING THE GUARD

WARNING:

• Always wear gloves when mounting or replacing the guard. Be careful of the blade on the guard and protect your hands from being injured by the blade.

• Always remove the battery pack from the product when you are assembling parts, making adjustments, cleaning, or when the product is not in use.

1. Remove the battery pack from the trimmer.

WARNING:

Always remove the battery pack from the product when you are assembling parts, making adjustments, cleaning, or when the product is not in use.

1. Remove the battery pack from the trimmer.

2. Remove the screw knob and the bolt from the front-assist handle.

3. Press the front-assist handle onto the shaft of the string trimmer. Make sure that the front-assist handle faces upward so that it points toward the top of the handle.

4. To attach the front-assist handle on the shaft, insert the bolt into the hole on the front-assist handle, and then use the screw knob to tighten the bolt.

Page 9

ASSEMBLY

TO ADJUST THE FRONT-ASSIST

HANDLE POSITION

TO ATTACH BATTERY PACK

The handle should be adjusted so that your front arm will be straight when using the trimmer.

To adjust the front-assist handle position, loosen the screw knob so that the frontassist handle can be moved to the desired position of the shaft. Tighten the screw knob so that the handle cannot move on the shaft during operation.

FIG. 5

Front-assist Handle

1. Make sure that the switch is in the OFF position.

2. Align the raised portion on the battery pack with the grooves on the bottom of the tool, and then slide the battery pack onto the tool as shown.

3. Ensure that the battery-release button on the battery pack snaps into place and the battery pack is secured to the tool before beginning operation.

NOTICE:

When placing the battery pack on the tool, be sure that the raised rib on the battery pack aligns with the groove on the tool and the latches snap into place properly. Improper assembly of the battery pack can cause damage to internal components.

Screw Knob

Bolt

TO ATTACH/REMOVE BATTERY

PACK (FIG 6)

FIG. 6

Battery-release

Button

TO REMOVE BATTERY PACK

1. Make sure that the switch is in the OFF position.

2. Press the battery-release button to release the battery pack.

3. Pull rearward on the battery pack to remove it from the tool.

WARNING:

Battery tools are always in operating condition. Therefore, the trigger switch should always be in the

OFF position when the tool is not in use or when carrying the tool at your side.

Page 10

OPERATION

HOLDING THE STRING TRIMMER

(FIG.7)

TO START/STOP THE STRING

TRIMMER (FIG.8)

FIG. 7 FIG. 8

Lock-off Button

Variable-speed

Trigger Switch

WARNING:

Dress properly to reduce the risk of injury when operating this tool. Do not wear loose clothing or jewelry. Wear eye and ear/hearing protection. Wear heavy, long pants, boots, and gloves. Do not wear short pants or sandals or go barefoot.

Before operating the unit, stand in the operating position and check that:

1. The operator is wearing eye protection and proper clothing.

2. One arm is slightly bent, and the hand on that arm is holding the rear handle.

3. The other arm is straight, with that hand holding the front-assist handle.

4. The trimmer head is parallel to the ground and easily contacts the material to be cut without the operator having to bend over.

Before starting the string trimmer:

• Make sure that you have a secure and balanced footing.

• Stand upright and hold the string trimmer in a relaxed position.

• Make sure that the cutting line is not touching the ground or any other objects.

• Hold the string trimmer with both hands: one hand on the rear handle and the other hand on the front-assist handle.

1. To turn the string trimmer on, press the lock-off button and then depress the variable-speed trigger switch.

2. The variable-speed trigger switch delivers higher speed with increased trigger pressure and lower speed with decreased trigger pressure.

3. To turn it off, release the variable-speed trigger switch and allow the trimmer to come to a complete stop.

WARNING:

Always remove the battery pack from the string trimmer during work breaks and after finishing work.

Page 11

OPERATION

USING THE STRING TRIMMER TIPS FOR BEST TRIMMING RE-

SULTS

FIG. 9

Direction of

Rotation

WARNING:

• To avoid serious personal injury, wear goggles or safety glasses at all times when operating this unit. Wear a face mask or dust mask in dusty locations. Wear proper clothing and footwear during operation to reduce the risk of injury that may be caused by flying debris.

Best Cutting

Area

CHECK FOR DAMAGED/WORN

PARTS BEFORE EACH USE

WARNING:

To prevent serious personal injury, remove the battery pack from the tool before servicing, cleaning, changing attachments or removing material from the unit.

Check the bump head, guard and frontassist handle and replace any parts that are cracked, warped, bent, or damaged in any away.

• Clear the area to be cut before each use.

Remove all objects, such as rocks, broken glass, nails, wire, or string that can be thrown or become entangled in the cutting attachment. Clear the area of children, bystanders, and pets. At a minimum, keep all children, bystanders and pets at least

100 ft. (30.5 m) away; there still may be risk to bystanders from thrown objects.

• Bystanders should be encouraged to wear eye protection. If you are approached, stop the motor and cutting attachment immediately.

The correct angle for the cutting attachment is parallel to the ground.

• This string trimmer allows you to rest the bump knob on the ground for more comfortable operation.

The line-cutting blade on the edge of the guard can dull over time. It is recommended that you periodically sharpen it with a file or replace it with a new blade.

WARNING:

Always wear gloves when mounting or replacing the guard or when sharpening or replacing the blade.

Note the location of the blade on the guard and protect your hand from injury.

• Do not force the trimmer. Allow the very tip of the line to do the cutting (especially along walls). Cutting with more than the tip will reduce cutting efficiency and may overload the motor.

• The cutting height is determined by the distance of the cutting line from the lawn surface.

• Grass over 8 in. (200 mm) should be cut by working from top to the bottom in small increments to avoid premature line wear or motor drag.

Page 12

OPERATION

• Slowly move the trimmer into and out of the area being cut, maintaining the cutting head position at the desired cutting height.

This movement can be either a forwardbackward motion or a side-to-side motion.

Cutting shorter lengths produces best results.

Always keep the trimming line fully extended.

Line release becomes more difficult as the cutting line becomes shorter.

WARNING:

Do not remove or alter the line cutting blade assembly. Excessive line length will cause the motor to overheat and may result in serious personal injury.

• Trim only when grass and weeds are dry.

• Wire and picket fences can cause extra string wear or breakage. Stone and brick walls, curbs, and wood may wear strings rapidly.

• Avoid trees and shrubs. Tree bark, wood moldings, siding, and fence posts can easily be damaged by the strings.

CLEAN THE TRIMMER AFTER

EACH USE

WARNING:

To prevent serious personal injury, remove the battery pack from the tool before servicing, cleaning, changing attachments or removing material from the unit.

ADJUSTING CUTTING LINE

FIG. 10

LENGTH (FIG 10)

Bump Knob

The trimmer head allows the operator to release more cutting line without stopping the motor. As line becomes frayed or worn, additional line can be released by lightly tapping the bump knob on the ground while operating the trimmer.

For best results, tap the bump knob on bare ground or hard soil. If line release is attempted in tall grass, the motor may overheat.

1. Clear any grass that may have wrapped itself around the motor shaft or trimmer head.

2. Use only a clean, dry and soft cloth to clean the tool. Never let any liquid get inside the tool; never immerse any part of the tool into a liquid.

3. Keep the air vents in the rear housing free from debris at all times.

NOTICE:

Obstructing the vents will prevent the air from flowing into the motor housing and may result in overheating or damage to the motor.

WARNING:

Never use water for cleaning your trimmer. Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to damage from various types of commercial solvents.

Use clean clothes to remove dirt, dust, oil, grease, etc.

Page 13

OPERATION

LINE REPLACEMENT

NOTICE:

Always use triangle-shaped twisted nylon cutting line with a diameter that does not exceed 0.08 in. (2.0 mm).

Using line other than that specified may cause the string trimmer to overheat or become damaged.

WARNING:

Never use metalreinforced line, wire, or rope, etc. These can break off and become dangerous projectiles.

WIND THE SPOOL WITH NEW

LINE

WARNING:

To prevent serious personal injury, remove the battery pack from the tool before servicing, cleaning, changing attachments or removing material from the unit.

1. Press the two release tabs on the spool base and remove the spool retainer by pulling it straight out (Fig.11).

2. Remove the spool. Use a clean cloth to clean the inner surface of the spool retainer and spool base.

NOTICE:

Always clean the spool retainer and spool base before reassembling the trimmer head.

6. Wind the line, in two even and tight layers, onto the spool. Wind the line in the direction indicated on the spool.

NOTICE:

Failure to wind the line in the direction indicated will cause the trimmer head to operate incorrectly.

7. Place the ends of the line in the two opposite notches in the spool, with approximately 5 in. (12.5 cm) protruding from each side (Fig.13).

8. Align the notches of the spool from which the lines protrude with the eyelets in the spool retainer and position the spool in the retainer (Fig.14).

9. Holding the spool and spool retainer, grasp one end of the line and pull it to release the line from the notch in the eyelet (Fig.15). Repeat with the other end.

10. With the spool base facing downward, align the slots in the spool retainer with the tabs on the spool base and press the retainer evenly down until it snaps into place (Fig.16).

NOTICE:

Make sure that the tabs on the spool base snap into place or the spool will come out during operation.

CAUTION:

After each line replacement, tap the bump knob on the ground for several times before trimming on grass to check that whether the cutting line can be released normally.

3. Check the spool retainer, spool and spool base for wear parts.

4. Take approximately 15 ft. (4.5 m) of 0.08 in. (2.0 mm) diameter cutting line. Fold the line in half and then adjust it so that one end is 4.5 in. (11 cm) longer than the other (Fig.12).

5. Hook the folded end of the cutting line onto either of the slots in the spool.

Page 14

FIG. 11

Tap

OPERATION

FIG. 12

4.5 in.

(11 cm)

FIG. 13 FIG. 14

FIG. 15 FIG. 16

Slot

Tap

Page 15

MAINTENANCE

WARNING:

All maintenance should only be carried out by a qualified service technician. Before cleaning or performing any maintenance, remove battery from the tool. For safe and proper operation, always keep the tool and its ventilation slots clean.

STORAGE

Clean the tool thoroughly before storing it.

Store the unit in a dry, well-ventilated area, locked-up or up high, out of the reach of children. Keep away from corrosive agents, such as garden chemicals and de-icing salts.

CLEANING

Always use only a soft, dry cloth to clean your string trimmer; never use detergent or alcohol. Clear any grass that may have wrapped itself around the motor shaft or trimmer head. Keep the air vents free of obstructions.

Page 16

TROUBLESHOOTING

PROBLEM

Tool does not work.

String trimmer stops while cutting.

Trimmer head will not advance line.

CAUSE

Low battery capacity.

SOLUTION

Charge the battery pack.

The motor shaft or trimmer head is bound with grass.

The motor is overloaded

The battery pack or string trimmer is too hot.

The motor shaft or trimmer head is bound with grass.

There is not enough line on the spool.

Stop the trimmer, remove the battery, and remove the grass from the motor shaft and trimmer head.

Move the trimmer head to cut the grass no more than 8 in. of length in a single cut. Remove the trimmer head from the grass and restart the tool.

Release the trigger switch, wait for the tool to cool down, and then start the tool again.

Stop the trimmer, remove the battery, and clean the motor shaft and trimmer head.

Remove the battery and replace the cutting line; follow the section “Line

Replacement” in this manual.

Page 17

Cordless String Trimmer

WARRANTY

90-DAY MONEY BACK GUARANTEE:

This MASTERFORCE TM brand power tool carries our 90-DAY Money Back

Guarantee. If you are not completely satisfied with your MASTERFORCE TM brand power tool for any reason within ninety (90) days from the date of purchase, return the tool with your original receipt to any MENARDS® retail store, and we will provide you a refund – no questions asked.

3-YEAR LIMITED WARRANTY:

This MASTERFORCE TM brand power tool carries our famous No Hassle 3-Year Limited

Warranty to the original purchaser. If, during normal use, this MASTERFORC TM power tool breaks or fails due to a defect in material or workmanship within three (3) years from the date of original purchase, simply bring this tool with the original sales receipt back to your nearest MENARDS® retail store. At its discretion, MASTERFORCE TM agrees to have the tool or any defective part(s) repaired or replaced with the same or similar MASTERFORCE TM product or part free of charge, within the stated warranty period, when returned by the original purchaser with original sales receipt. Not withstanding the foregoing, this limited warranty does not cover any damage that has resulted from abuse or misuse of the Merchandise. This warranty: (1) excludes expendable parts including but not limited to blades, brushes, belts, bits, light bulbs, and/or batteries; (2) shall be void if this tool is used for commercial and/or rental purposes; and (3) does not cover any losses, injuries to persons/property or costs. This warranty does give you specific legal rights and you may have other rights, which vary from state to state. Be careful, tools are dangerous if improperly used or maintained.

Seller’s employees are not qualified to advise you on the use of this Merchandise.

Any oral representation(s) made will not be binding on seller or its employees. The rights under this limited warranty are to the original purchaser of the Merchandise and may not be transferred to any subsequent owner. This limited warranty is in lieu of all warranties, expressed or implied including warranties or merchantability and fitness for a particular purpose. Seller shall not be liable for any special, incidental, or consequential damages. The sole exclusive remedy against the seller will be for the replacement of any defects as provided herein, as long as the seller is willing or able to replace this product or is willing to refund the purchase price as provided above.

For insurance purposes, seller is not allowed to demonstrate any of these power tools for you.

For questions / comments, technical assistance or repair parts –

Please call toll free: 1-866-917-4374 (M-F 8:30am – 5:00pm EST).

SAVE YOUR RECEIPTS

THIS WARRANTY IS VOID WITHOUT THEM

Page 18

© 2018 Menard, Inc., Eau Claire, WI 54703 02/2018