QCY TWS Bluetooth Earbuds QCY-T5 User Manual

 QC —Z
QCY-T5
TWS Bluetooth Earbuds
Function Introduction
Overview
Choose Your Eartips
LED
Touch bar
Tuning Hole
Pogo Pins
Please try medium eartips first as they fit most people.
Functions Current status Operation/result LED Prompt
Power-off with no Keep touching the bar for 1s to power on LED blinks TONE
connectivity record and earbud will auto enter pairing mode red and green
eee TWS Power off then keep LED blink red and
ode touching the bar for 5s to Double touch the bar to enter TWS mode green then right LED \
enter pairing mode turns off
Power-off Keep touching the bar for 1s LED glows green
for 1s
Power-on LED glows green TONE
Charging Pick up earbuds from the case for e 8
power off, if earbuds are not connected to device) LED glows red for 2s
Power-off Power-on TONE
Pop earbud into the case to power off LED glows red
LED blinks red and green 3
times then earbud turns off(if
power off both earbuds,
then keep touching both bars
Remove Power-off Keep touching the bar for 10s to remove for Los to remove connectivity \
connectivity record connectivity record one LED blinkeat first, then >
both LEDs start to blink red
and green for 3 times)
Answer/end call Incoming call/calling Double touch the bar \ TONE
Ignore call Incoming call Keep touching the bar for 2s \ TONE
Voice assistant Connected Triple touch left bar \ TONE
: . . Triple touch right bar to switch on/off On: two b
Gaming mode Playing/gaming gaming mode \ Off: three beeps
. . . Double touch the bar to pause,double touch
Music pause/play Music playing again to resume playin \ \
: : : Keep touching right/left bar to skip track
Skip track Music playing forward/backward \ \
How to Pair
First Time Pairing:
1. Pick up both earbuds.
2. On cellphone, search for QCY-T5 and tap to connect.
“Once paired earbuds will auto power on upon picking
up from the case. If earbuds fail to auto power on, please
charge them and try again.
Switch Paired Device:
1. Turn off phoneA's Bluetooth faculty and earbuds will
auto disconnect and enter into pairing mode.
2. On phoneB, search for QCY-T5 and tap to connect.
*Multi-point connection is not available. Earbuds will
auto reconnect to phoneB upon powering up again.
Warranty Card
Warranty Period
12 months after you purchase this item.(or you may
inquire your local shopper for more details.)
Free Service:
Supposing any defects caused by quality issues occur
within the warranty period, please take this warranty
card and purchase receipts to your distributor for free
exchange service.
Model Number:
Date of Purchasing:
User's Name:
User's Phone:
User's Address:
Shop's Name:
Shop's Address:
Comments:
Free exchange service will not be accessed under
following circumstances:
1. Damages caused unauthorized disassembly.
2. Defects or physical damages caused by leaking or
dropping off.
3. Damages by act of God.Supposing your item is within
any damages or defects except the above circumstances,
please return to us or your distributor for free repairing.
Factory Setting
(Try the following steps to fix connectivity issue)
Set to factory:
1. On cellphone, search for QCY-T5, tap and choose ignore
or cancel pairing.
2. Pick up two earbuds, keep touching both bars for 8s or
until LEDs glow red for 2s to power off.
3. Keep touching both bars for 10s or until LEDs blink red
and green 3 times then blink red to set earbuds to factory.
“Please refer "First Time Pairing" to connect after factory
setting.
FCC Statement
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more
of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation
is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including
interference that may cause undesired operation.
Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to
operate the equipment.
How to Wear
1.Rotate earbud and pop it into your ear then shake
head to check wearing stability.
2.Please adjust mic towards your mouth to gain better
calling experience.
Three-way Calling & Switch
Earphones are connected with phoneA. Double press
MFB to answer incoming call from phoneB. If another call
is coming from phoneC in sync, double press MFB to put
the first call on held while activating the second call.
Hold MFB to switch between active call and held call.
Ignore the second call in three-way calling: earphones are
connected with phoneA. Double press MFB to answer
incoming call from phoneB. If another call is coming from
phoneC in sync, hold MFB to ignore the second call while
keeping the first call.
Hazardous substances and their contents in the item
Hazardous Substances
Part Cr
Name | Pb | Hg | Cd (vi) |PBB |PBDE| DIBP |DEHP| DBP | BBP
Mainbody| X | O[JOJO|OJ|OJOJO|O|O
Battery [O|OJ|OJO|JOJOJOJO|OJ|O
Eartips [O | OJOJO|OJOJOJO|O|O
Accessories] O | OJO|OJOJOJO|OJOJ|O
Charging хо ооо
This form is made by SJ/T 11364 regulation.
O: means that hazardous substance content in the
homogeneous materials of this part is within the
limits of (EU) 2015/863 regulation .
X : means that hazardous substance content in ‚at least,
one certain homogeneous material of this part is
beyond the limits of (EU) 2015/863 regulation ,but
there is no mature alternative in the industry at present,
it still conforms to the EU ROHS Directive in the scope
of exemption.
Notes: Please arrange using time properly as your hearing
may be damaged by using the device for a long time.
Perform standard: Q/HL 1-2019 ; Q/HL 2-2017
Manufacturer: Dongguan Hele Electronics Co., Ltd.
Address: Daojiao Town, Dongguan City, Guangdong, China
Mono Mode
1, Power off earbud then keep touching the bar for 5s to enter
pairing mode (LED blinks red and green )
2. On cellphone, search for QCY_T5
3. Tap to connect
Charging Earbud
Push earbud into the case to charge. LED will glow solid red
when charging and turn to green for 1 minute once top up.
Charging the Case
Charge the case via USB cable. LED will glow solid green
when charging and turn off once top up.
Product Parameters
Model:In1925
Bluetooth version: V5.0
Charging time: approx. 2hr
Talking time: approx. 4hr
Operation range: 10m(with no obstacle)
Battery type: li-ion
Battery capacity(earbud):3.7V 40mAh
Battery capacity(charging case):3.7V 380mAh
Input parameter(charging case):5V ==500mA
Bluetooth profiles: HSP/HFP/A2DP/AVRCP
Pairing name: QCY-T5
Stand time: approx. 70hr
Music time: approx. 4 or 5hr
Tips
1. Before using the headset, please read the manual
carefully and keep it for future references.
2. The headset need to be fully charged prior to first-time use.
3. If the headset is left unused for over two weeks, please
recharge it periodically.
4, Please use the chargers made by qualified manufacturer.
5. If the headset cannot be found by your phone, please check
whether it is in pairing mode; if left unconnected for a long
while, the headset will exit pairing mode, please re-enter
the mode; if a procedure error of your phone occurs, reboot
it; if a procedure error of the headsetoccurs, reboot or reset it.
Caveats
1. Never disassemble or modify your headset for any
reasons to avoid any damages and danger.
2. Do not store the headset in extreme temperatures (under
0°C or over 45°C).
3. Avoid using the indicator close to the eyes of children or
animals.
4. Do not use this headset during a thunderstorm to avoid
irregular function and increased risk of electricshock.
5. Do not use harsh chemicals or strong detergents to
clean the headset.
6. Keep the headset dry.
До м г
064 ©
CMIIT ID: 2019DP6793