York Fitness G510 Instruction Manual
Show HTML Add to My manuals36 Pages
York Fitness G510 is a versatile home gym system designed to provide a full-body workout experience. With a weight capacity of up to 50kg and various attachments, it allows users to perform a wide range of exercises targeting different muscle groups. The adjustable seat and multiple press arms enable customization for users of different heights and fitness levels. The G510 features a leg extension unit for leg workouts, a lat pulldown attachment for back exercises, and a pec deck for chest exercises.
advertisement
F I T N
E S
S
Press 1 : 1 Resistance same as weight selectedLat Pulldown 1 : 1 Resistance same as weight selected
Low Row1.5 : 1 Resistance 1.5 times weight selected
WEIGHT : RATIO
Press
Lat
Low Row
Leg Ext.
Pec
2 : 1 or 1:1 of weight selected (max 100kg)
1 : 1 of weight selected (max 50kg)
1 : 1 of weight selected (max 50kg)
1 : 1 of weight selected (max 50kg)
1 : 1 of selected weight (max 50kg)
TOP PLATE & STEM PLUS 9 WEIGHT PLATES
GIVES TOTAL 50 KG ( 110 lbs ) Dimensions when built :
L = 160cm, W = 96cm, H = 208cm. G.W. = 104kg.
Maximum user weight 100kg
30
M10 x 72mm HEX HEAD BOLT x 4
49
We recommend you have someone assist you in lifting and assembling your YORK G510 Gym.
Follow these instructions carefully and it will make it easier for you to assemble your YORK G510 Gym.
Only half tighten bolts/nuts (unless otherwise stated) until assembly is complete.
INSTRUCTION
1
Attach the RIGHT FRONT UPRIGHT SUPPORT (1),
LEFT FRONT UPRIGHT SUPPORT (2) to the BOTTOM CROSS SUPPORT (3) using fixings
( Nuts / bolts / washers etc ) as detailed.
Locate the REAR STABILIZER (4) to the BOTTOM CROSS SUPPORT (3) and secure using fixings ( Nuts / bolts / washers etc ) as detailed.
M10 x 23mm x 2mm
FLAT WASHER x 8
48
M10 NYLON
LOCKNUT x 4
49
30
30
49
48
49
49 48
REAR
4
STABILIZER
3 BOTTOM CROSS
SUPPORT
2
LEFT FRONT
UPRIGHT
SUPPORT
RIGHT FRONT
UPRIGHT
SUPPORT
1
49 48
SHOULD YOU REQUIRE ANY ASSISTANCE REGARDING THIS PRODUCT PLEASE CONTACT YORK DIRECTLY
YORK G510 / 02
INSTRUCTION
2
Insert both WEIGHT PLATE POSTS (6) into the rear of BOTTOM CROSS SUPPORT (3) and secure using fixings ( Nuts / Bolts / Washers etc ) as detailed.
Make sure that the 65mm bolts pass through the holes at the bottom of the WEIGHT PLATE POSTS (6).
Slide the 2 x 63.5mm RUBBER BUMPER PAD (75) to the bottom of the WEIGHT PLATE POSTS (6).
Attach the
MAIN FRAME SUPPORT
(5) to the front end of
BOTTOM CROSS SUPPORT
(3) with two BOTTOM CONNECTING PLATE (7) and secure using fixings ( Nuts / Bolts / Washers etc) as detailed.
32
29
49
M10 x 75mm HEX HEAD BOLT x 4
M10 x 65mm HEX HEAD BOLT x 2
48
M10 x 23mm x 2mm
FLAT WASHER x 12
M10 NYLON
LOCKNUT x 6
CHROME WEIGHT
PLATE POST
MAIN FRAME
SUPPORT
BOTTOM
CONNECTING
PLATE
Slide the
2 x 63.5mm RUBBER
BUMPER PAD
(75) to the bottom of the
WEIGHT PLATE POST
(6).
RUBBER BUMPER PAD through the holes at the bottom of the
WEIGHT PLATE POST
(6).
BOTTOM CONNECTING
PLATE
SHOULD YOU REQUIRE ANY ASSISTANCE REGARDING THIS PRODUCT PLEASE CONTACT YORK DIRECTLY
YORK G510 / 03
63
INSTRUCTION
3
Ensure the entry point for the SELECTOR PIN (64) faces towards the left hand side on each of the plates.
Slide each of the 9 x CAST IRON WEIGHT PLATES (61) down the WEIGHT PLATE POST (6).
Locate the CAST IRON TOP PLATE (62) on top of the plates ( Ensure that the hole faces towards left ).
Find the M12 x 40mm TOP PLATE FIXING BOLT (63)
& WEIGHT PLATE SELECTOR STEM (8).
While keeping hold of the top of the WEIGHT SELECTOR
STEM (8) slide it down into the middle of the CAST IRON
TOP PLATE (62) & CAST IRON WEIGHT PLATES (61).
Line up the threaded hole on the CAST IRON TOP PLATE (62) with the threaded hole on the SELECTOR STEM (8).
Insert & tighten the M12 x 40mm FIXING BOLT (63).
FIXING BOLT
ENTRY POINT FOR SELECTOR PIN FACES
TOWARDS THE LEFT SIDE.
SELECTOR
PIN
M12 x 40mm FIXING BOLT x 1
WEIGHT PLATE
SELECTOR STEM
THREADED HOLE
ON WEIGHT
SELECTOR STEM
CAST IRON
TOP PLATE
CAST IRON
WEIGHT
PLATES
Slide each of the
9 x CAST IRON
WEIGHT PLATES (61) down the WEIGHT
PLATE POST (6).
SHOULD YOU REQUIRE ANY ASSISTANCE REGARDING THIS PRODUCT PLEASE CONTACT YORK DIRECTLY
YORK G510 / 04
INSTRUCTION
4
Locate and attach the TOP CROSS SUPPORT (9)
& fixings. ( Ensure that the holes on the underside of the TOP CROSS SUPPORT (9) are located over the WEIGHT PLATE POSTS (6). )
Attach the top cross support to MAIN FRAME
SUPPORT (5) with TOP CONNECTING
PLATE (R) (11) and TOP CONNECTING
PLATE (L) (10) and secure using fixings
( Nuts / Bolts / Washers etc) as detailed.
31
49
TOP CONNECTING
PLATE (L)
29
49
10
29
M10 x 75mm HEX HEAD BOLT x 4
31
49
M10 x 68mm HEX HEAD BOLT x 2
48
M10 x 23mm x 2mm
FLAT WASHER x 12
M10 NYLON
LOCKNUT x 6
5
9
TOP CROSS
SUPPORT
49
48
TOP CONNECTING
PLATE
(R)
11
49
48
SHOULD YOU REQUIRE ANY ASSISTANCE REGARDING THIS PRODUCT PLEASE CONTACT YORK DIRECTLY
YORK G510 / 05
42
INSTRUCTION
5
Locate the LEG EXTENSION UNIT (12) and fix to the front of the BOTTOM CROSS
SUPPORT (3) using the detailed fixings.
( Ensure that the LOW PULL BAR STOP BRACKET faces forwards. )
51
M12 x 75mm HEX HEAD BOLT x 1
47 65
M12 x 25mm x 2mm
FLAT WASHER x 2
M12 NYLON
LOCKNUT x 1
M12 PLASTIC
NUT CAP x 2
ROUND HEAD
PULL PIN 3
BOTTOM
CROSS
SUPPORT
STOP
BRACKET
FACES
FORWARDS
LEG EXTENSION UNIT
SHOULD YOU REQUIRE ANY ASSISTANCE REGARDING THIS PRODUCT PLEASE CONTACT YORK DIRECTLY
YORK G510 / 06
INSTRUCTION
6
Locate the PEC CAM COVER (R) (14)
& PEC CAM COVER (L) (15) to the
PEC ARM TOP SUPPORT (13) and fixings.
Assemble as per diagram using the fixings shown & tighten .
PEC CAM
COVER (L)
44
M5 x 10mm FLAT HEAD
MACHINE SCREW x 8
PEC CAM
COVER (R)
PEC ARM TOP
SUPPORT )
INSTRUCTION
7
Find the
PIVOT SHAFT ROD
(16) and fixings.
Line up the top support assembly and slide the
PIVOT SHAFT ROD
(16) through the
PEC ARM TOP SUPPORT
(13) and the
TOP CROSS SUPPORT
(9)
Tightly secure in place using fixings
(Bolts & Washers) as detailed.
PIVOT SHAFT ROD
41
M8 x 25mm ALLEN
HEAD BOLT x 2
53
M8 x 28mm x 2mm
FLAT WASHER x 2
HAND WHEEL
KNOB
58
13
TOP CROSS
SUPPORT
9
NOTE:
Locate
HAND WHEEL KNOB
(58) through
PEC ARM
TOP SUPPORT
(13) and tighten into
TOP CROSS SUPPORT
(9)
SHOULD YOU REQUIRE ANY ASSISTANCE REGARDING THIS PRODUCT PLEASE CONTACT YORK DIRECTLY
YORK G510 / 07
INSTRUCTION
8
Slide one ARM FOAM ROLLER (80) onto the RIGHT PEC ARM (17) .
Slide one ARM FOAM ROLLER (80) onto the LEFT PEC ARM (18) .
LEFT PEC ARM
RIGHT PEC ARM
NOTE: Moisten the inside of the foam rollers with water
or house hold furniture polish before you slide it
onto the pec arm.
SHOULD YOU REQUIRE ANY ASSISTANCE REGARDING THIS PRODUCT PLEASE CONTACT YORK DIRECTLY
YORK G510 / 08
INSTRUCTION
9
Fit the PEC ARM ASSEMBLIES (17 & 18) into the PEC ARM TOP SUPPORT (13) and tightly secure using fixings (Bolts & washers) as detailed.
Insert the
HANDLE PIVOT SHAFT
(19) into the bottom of the
PEC ARM (L)
(18) and secure the shaft using the fixings.
Thread the PRESS HANDLE (21) onto the HANDLE PIVOT SHAFT (19) via
FIXING BRACKET
(20).
(Repeat same for opposite side)
50
33
43
49
M10 x 60mm HEX HEAD BOLT x 2
M10 x 20mm HEX HEAD BOLT x 2
48
M10 x 23mm x 2mm
FLAT WASHER x 4
M10 NYLON
LOCKNUT x 2
M10 x 38mm x 2mm
FLAT WASHER x 2
PEC ARM
ASSEMBLY (L)
PEC ARM
ASSEMBLY (R)
HANDLE
PIVOT SHAFT
FIXING
BRACKET
PRESS
HANDLE
SHOULD YOU REQUIRE ANY ASSISTANCE REGARDING THIS PRODUCT PLEASE CONTACT YORK DIRECTLY
YORK G510 / 09
INSTRUCTION
10
Fix the BACK REST UPHOLSTERY (82) to the MAIN FRAME POST (5).
The BACK REST UPHOLSTERY (82) should be central to the MAIN FRAME POST (5).
Fix the SEAT UPHOLSTERY (81) to the BOTTOM CROSS SUPPORT (3).
The SEAT UPHOLSTERY (81) should be central to the BOTTOM CROSS SUPPORT (3).
Slide the FOAM ROLLER POST (22) through the holes, in LEG EXTENSION UNIT (12) , then fit two LEG FOAM ROLLERS (79) as illustrated.
NOTE: Moisten the inside of the foam rollers
with a little water or household furniture
polish before you slide it onto the
FOAM ROLLER POST (22).
39
40
52
M8 x 65mm HEX HEAD BOLT x 2
M8 x 90mm HEX HEAD BOLT x 2
M8 x 16mm x 2mm
FLAT WASHER x 4
BACK REST
UPHOLSTERY
F I T
N
E S
S
5
3
SEAT
UPHOLSTERY
FOAM
ROLLER POST
LEG FOAM
ROLLERS
SHOULD YOU REQUIRE ANY ASSISTANCE REGARDING THIS PRODUCT PLEASE CONTACT YORK DIRECTLY
YORK G510 / 10
INSTRUCTION
11
Locate the LAT PULL CABLE (88) with threaded bolt and route as shown.
Fix a SNAP LOCK HOOK (60) to the end with the ball stop.
(NOTE: Fix the pulley assemblies in place once cable is
routed - this may save them having to be removed
and re-located.)
Not inside slot
Pulley cover wrong
Exit point
Pulley cover right
Entry point
Locate and fit all PULLEY WHEEL (83) + PULLEY
WHEEL COVER ASSEMBLIES (84) as shown using fixings
(Nuts / Bolts / Washers etc) as detailed.
When fitted correctly pulley covers will protect you from potential squeeze points ensure that the cable enters and exits from the pulley through the channels provided in the pulley covers.
Ensure that the cables are located in the grooves where they enter and exit the pulley.
54
Ensure PULLEY WHEEL SPACERS (54) are fitted where illustrated.
11.5mm LONG
SPACER x
48
M10 NYLON
LOCKNUT x 6
34 Locate 1 x ADJUSTABLE PULLEY BRACKET (23) and the fixings to assemble the central pulley assembly.
32
M10 x 50mm HEX HEAD BOLT x 4
M10 x 65mm HEX HEAD BOLT x 2
SPACER 49
M10 x 23mm x 2mm
FLAT WASHER x 12
ADJUSTABLE
PULLEY BRACKET
THREAD THIS
END FIRST
SHOULD YOU REQUIRE ANY ASSISTANCE REGARDING THIS PRODUCT PLEASE CONTACT YORK DIRECTLY
YORK G510 / 11
LAT PULL CABLE & PULLEY ASSEMBLIES
LAT
PULL
CABLE
3025mm
LONG
88
Screw the threaded end of the LAT PULL CABLE (88) about half-way into the top of the WEIGHT SELECTOR STEM (8) once the thread is about half way down, tighten the lock nut.
NOTE: You can make slight adjustments to the cable tension
later using the threaded cable end and lock nut.
88
LAT PULL CABLE 3025mm LONG x 1
SHOULD YOU REQUIRE ANY ASSISTANCE REGARDING THIS PRODUCT PLEASE CONTACT YORK DIRECTLY
YORK G510 / 12
INSTRUCTION
1 2
Lay 1 x
SQUARE PULLEY FIXING PLATE
(90) on floor, slot FEMALE SCREW BOLTS (91) through the 4 holes from under side upwards and slot a
PULLEY COVER (84) onto the top 2 bolts followed by
PULLEY WHEEL
(83) as illustrated in step A.
Feed
PEC CABLE
(86) around both
PULLEY WHEELS (83) as illustrated in step B.
Slot a
PULLEY COVER
(84) onto the bottom 2 bolts followed by PULLEY WHEELS (83) and wrap
CONNECTING CABLE (87) around them as illustrated in step D.
Slot PULLEY COVER (84) on top of
2 x
PULLEY WHEELS
(83) as illustrated in step C.
Note: Be sure to fit
PEC CABLE
(86) through plastic guides in each
PULLEY COVER
(84) as illustrated.
D
Slot PULLEY COVER (84) on top of 2 x PULLEY WHEELS (83) as illustrated in step E.
Note: Be sure to fit
PEC CABLE
(86) through plastic guides in each
PULLEY COVER (84) as illustrated.
A
Fit other SQUARE PULLEY FIXING
PLATE
(90) over bolts and attach using
MALE SCREW BOLT
(92) as detailed.
91
10mm X 35mm X M8
FEMALE SCREW BOLT x 4
92
86
M8 X 15mm
MALE SCREW BOLT X 4
PEC CABLE 1780mm LONG x 1
87
E
C
CONNECTING
CABLE
87
F
B
PEC
CABLE
86
CONNECTING CABLE 3135mm LONG x 1
SHOULD YOU REQUIRE ANY ASSISTANCE REGARDING THIS PRODUCT PLEASE CONTACT YORK DIRECTLY
YORK G510 / 13
INSTRUCTION
1 3
Attach each end of PEC CABLE (86 to PEC ARMS
(17 & 18) using fixings (nuts/bolts/washers etc) as detailed.
NOTE:
Be sure to loop assembled pulley bracket from
instruction12around back of
BACK REST
UPHOLSTERY
(82)
37
M8 X 35mm HEX HEAD BOLT X 2
Mount 2 x PULLEY WHEELS (83) with their
PULLEY COVERS (84) underneath PEC CABLE (86) into brackets on
TOP CONNECTING PLATES
(10 & 11) using fixings (Nuts / bolts / washers etc) as detailed.
34
46
49
52
M10 X 23mm
WASHER X 2
52 3 7
52
M10 X 50mm HEX HEAD BOLT X 4
46
37
52
52
46
84 83 84 49 34
M8 X 16mm
WASHER X 2
M8 NYLON
LOCKNUT X 2
34
49
84
83
84
23
86
PEC
CABLE
SHOULD YOU REQUIRE ANY ASSISTANCE REGARDING THIS PRODUCT PLEASE CONTACT YORK DIRECTLY
YORK G510 / 14
INSTRUCTION
14
Attach screw end of CONNECTING CABLE (87) to top of
BENCH PRESS RATIO BRACKET
(26).
Locate
PULLEY WHEEL
(83) above loop of
CONNECTING CABLE (87) and attach
PULLEY WHEEL (83) inside
HOOKED PULLEY BRACKET (93) using fixings as illustrated, then hook to triangular bracket on
BOTTOM CROSS SUPPORT
(3).
52 46
49
M8 X 16mm
WASHER X 2
48
M8 NYLON
LOCKNUT X 1
M10 X 23mm
WASHER X 2
M10 NYLON
LOCKNUT X
38
34
M8 X 30mm HEX HEAD BOLT X 1
1
M10 X 50mm HEX HEAD BOLT X 1
CONNECTING
CABLE
87
46
52
52
38
26
83
84
48
49
93
49
34
BENCH PRESS
RATIO BRACKET
SHOULD YOU REQUIRE ANY ASSISTANCE REGARDING THIS PRODUCT PLEASE CONTACT YORK DIRECTLY
YORK G510 / 15
INSTRUCTION
15
Locate the LOW PULL CABLE (85) and insert small ball end first and route as illustrated.
33
When fitted correctly pulley covers will protect you from potential squeeze points.
Ensure that the LOW PULL CABLE (85) enters and exits from the pulley through the channels provided in the pulley covers.
Once the cable has been routed, locate and fix 3 x PULLEY ASSEMBLIES as shown.
Ensure that you use PULLEY COVER
ASSEMBLIES (84) where shown.
49
M10 x 60mm HEX HEAD BOLT x 1
48
M10 x 23mm x 2mm
FLAT WASHER x 4
M10 NYLON
LOCKNUT x 2
55
8.5mm LONG
SPACER x 2
84
83
84
49
94
LOW PULL CABLE
48
SPACER
49
55
84
83
84
55
49
33
35
START
HERE
48
49
84
83
84
Attach end of CONNECTING CABLE (87) to left side of
BOTTOM CROSS SUPPORT
(3) using 2 x
PULLEY WHEELS
(83) fixing bolt as illustrated.
M10 x 125mm HEX HEAD BOLT x 1
SHOULD YOU REQUIRE ANY ASSISTANCE REGARDING THIS PRODUCT PLEASE CONTACT YORK DIRECTLY
YORK G510 / 16
LOW PULL CABLE & PULLEY ASSEMBLIES
85
LOW PULL
CABLE
3850mm LONG
85
LOW PULL
CABLE
3850mm LONG
85
LOW PULL CABLE 3850mm LONG x 1
SHOULD YOU REQUIRE ANY ASSISTANCE REGARDING THIS PRODUCT PLEASE CONTACT YORK DIRECTLY
YORK G510 / 17
INSTRUCTION
16
Locate 2 x PULLEY ASSEMBLIES and fixings to connect the ADJUSTABLE PULLEY ASSEMBLY (23).
Use the bottom hole on the adjustable pulley bracket as the upper holes can be used to increase the tension later on in the product’s life.
Screw the threaded end of the CONNECTING CABLE (87) about half way into the end of the RATIO PULLEY BRACKET (26) before the pulley assembly fixing.
NOTE: This can be used to make slight adjustment
to the cable tension later.
Locate 1 x PULLEY ASSEMBLY and fixings to connect the RATIO PULLEY ASSEMBLY (26).
34
49
M10 x 50mm HEX HEAD BOLT x 2
M10 x 23mm x 2mm
FLAT WASHER x 4
48
M10 NYLON
LOCKNUT x 2
RATIO PULLEY
BRACKET
23
ADJUSTABLE
PULLEY
ASSEMBLY
34
49
84
CONNECTING
CABLE
83
84
49
48
57
PEC RATIO PIN
SHOULD YOU REQUIRE ANY ASSISTANCE REGARDING THIS PRODUCT PLEASE CONTACT YORK DIRECTLY
YORK G510 / 18
PULLEY ASSEMBLY
85
LOW PULL
CABLE
3850mm LONG
85
LOW PULL
CABLE
3850mm LONG
SHOULD YOU REQUIRE ANY ASSISTANCE REGARDING THIS PRODUCT PLEASE CONTACT YORK DIRECTLY
YORK G510 / 19
INSTRUCTION
17
Attach SNAP LOCK HOOKS (60) x 2 to both ends of the CHAIN (59) and connect one end to LOW PULLEY
CABLE (85) and other end to LOW PULL CABLE (85).
Using the SNAP LOCK HOOKS (60) attach the TOP LAT BAR (28) and LOW PULLING BAR (27).
28
60
59
60
85
27
SHOULD YOU REQUIRE ANY ASSISTANCE REGARDING THIS PRODUCT PLEASE CONTACT YORK DIRECTLY
YORK G510 / 20
PEC CURL EXERCISE
You can perform this exercise when HAND WHEEL KNOB (58) is fixed as shown.
58
HAND
WHEEL
KNOB
SHOULD YOU REQUIRE ANY ASSISTANCE REGARDING THIS PRODUCT PLEASE CONTACT YORK DIRECTLY
YORK G510 / 21
PRESS EXERCISE
You can perform this exercise when HAND WHEEL KNOB (58) is removed as shown.
SHOULD YOU REQUIRE ANY ASSISTANCE REGARDING THIS PRODUCT PLEASE CONTACT YORK DIRECTLY
YORK G510 / 22
LOW PULLEY EXERCISE
You can perform this exercise when RETAINING PIN (56) is fitted as shown.
RETAINING PIN
56
SHOULD YOU REQUIRE ANY ASSISTANCE REGARDING THIS PRODUCT PLEASE CONTACT YORK DIRECTLY
YORK G510 / 23
LEG EXTENSION / CURL EXERCISE
You can perform this exercise when RETAINING PIN (56) is removed as shown.
SHOULD YOU REQUIRE ANY ASSISTANCE REGARDING THIS PRODUCT PLEASE CONTACT YORK DIRECTLY
YORK G510 / 24
PRESS HANDLE ADJUSTMENT: NARROW / WIDE GRIP
Loosen the PRESS HANDLE (21) by unscrewing anti-clockwise and pulling outwards as show.
17 & 18
1.
21
2.
Pull & rotate the
FIXING BRACKET
(20) out from the
PEC ARM
(17/18).
4.
17 & 18
20
3.
Fold handle up onto side of PEC ARM
(17/18).
Secure
PRESS HANDLE
(21) onto
FIXING BRACKET (20) by screwing clockwise until tight.
To revert to narrow grip reverse above instructions.
6.
21
21
5.
17 & 18
20
SHOULD YOU REQUIRE ANY ASSISTANCE REGARDING THIS PRODUCT PLEASE CONTACT YORK DIRECTLY
YORK G510 / 25
PEC ARM LOCKING HAND WHEEL
When performing the Pec Exercise ensure the HAND WHEEL KNOB (58) is fitted securely first.
When performing the Press Exercise ensure the HAND WHEEL KNOB (58) is removed first.
58
WEIGHT RATIO ADJUSTMENT FOR PEC / PRESS ARMS
When performing the Press Exercise you can increase the max weight from 50kg to 100kg.
Max Weight 100KG, (2:1 Ratio, 5kg plate = 10kg)
Fit
PULL PIN
(57) to retaining
LOW PULL CABLE (85)
to BOTTOM CROSS SUPPORT (3).
Max Weight 50kg, (1:1 Ratio, 5kg plate = 5kg)
Remove PULL PIN (57) from LOW PULL CABLE (85)
and fit back into BOTTOM CROSS SUPPORT (3)
only for storage.
85
3 57
LEG EXTENSION ASSEMBLY RETAINING PIN
When performing Leg Extension / Curl Exercise ensure PULL PIN (56) is removed from
LEG EXTENSION UNIT (12) first and inserted into storage hole under SEAT (81) in BOTTOM
CROSS SUPPORT (3).
When using low pulley ensure PULL PIN (56) is fitted to
LEG EXTENSION UNIT
(12) first and locked in the down position.
12
56
3
SHOULD YOU REQUIRE ANY ASSISTANCE REGARDING THIS PRODUCT PLEASE CONTACT YORK DIRECTLY
YORK G510 / 26
EXPLODED PARTS DRAWING
31
49
49
48
6
88
8
73
63
64
32
49
49
48
49
48
62
61
75
SHOULD YOU REQUIRE ANY ASSISTANCE REGARDING THIS PRODUCT PLEASE CONTACT YORK DIRECTLY
YORK G510 / 27
EXPLODED PARTS DRAWING
SHOULD YOU REQUIRE ANY ASSISTANCE REGARDING THIS PRODUCT PLEASE CONTACT YORK DIRECTLY
YORK G510 / 28
EXPLODED PARTS DRAWING
F
T
N
E
S
S
SHOULD YOU REQUIRE ANY ASSISTANCE REGARDING THIS PRODUCT PLEASE CONTACT YORK DIRECTLY
YORK G510 / 29
PARTS LIST
5630-17
5630-18
5630-19
5630-20
5630-21
5630-22
5630-23
5630-25
5630-26
5630-27
5630-28
5630-29
5630-30
5630-31
5630-32
5630-33
5630-01
5630-02
5630-03
5630-04
5630-05
5630-06
5630-07
5630-08
5630-09
5630-10
5630-11
5630-12
5630-13
5630-14
5630-15
5630-16
5630-34
5630-90
5630-37
5630-38
5630-39
5630-40
5630-41
5630-42
5630-43
5630-44
5630-45
5630-46
5630-47
KEY NO. PART NO. Q'TY(PCS) DESCRIPTION
30
31
32
33
26
27
28
29
21
22
23
25
17
18
19
20
13
14
15
16
9
10
11
12
7
8
5
6
3
4
1
2
39
40
41
42
34
35
37
38
43
44
45
46
47
4
3
4
2
1
8
1
1
1
1
2
1
2
2
1
1
1
1
1
1
1
1
1
1
2
1
1
2
1
1
1
1
2
1
2
2
2
1
10
1
2
3
2
8
1
RIGHT FRONT UPRIGHT SUPPORT
LEFT FRONT UPRIGHT SUPPORT
BOTTOM CROSS SUPPORT
REAR STABILIZER
MAIN FRAME SUPPORT
WEIGHT PLATE POST ( CHROME )
BOTTOM CONNECTING PLATE
SELECTOR STEM
TOP CROSS SUPPORT
TOP CONNECTING PLATE ( L )
TOP CONNECTING PLATE ( R )
LEG EXTENSION UNIT
PEC TOP SUPPORT
PEC CAM COVER ( R )
PEC CAM COVER ( L )
PIVOT SHAFT ROD
PEC ARM ( R )
PEC ARM ( L )
PEC HANDLE PIVOT SHAFT
PEC FIXING BRACKET
PRESS HANDLE
LEG FOAM ROLLER POST
CABLE ADJUSTABLE PULLEY BRACKET
CABLE ADJUSTABLE BOLT
BENCH PRESS RATIO BRACKET
LOW PULLING BAR
TOP LAT BAR
M10 X 75mm HEX HEAD BOLT
M10 X 72mm HEX HEAD BOLT
M10 X 68mm HEX HEAD BOLT
M10 X 65mm HEX HEAD BOLT
M10 X 60mm HEX HEAD BOLT
M10 X 50mm HEX HEAD BOLT ( TL= 15mm )
M10 X 125mm HEX HEAD BOLT
M8 X 35mm HEX HEAD BOLT
M8 X 30mm HEX HEAD BOLT
M8 X 90mm HEX HEAD BOLT
M8 X 65mm HEX HEAD BOLT
M8 X 25mm ALLEN HEAD BOLT
M12 X 75mm HEX HEAD BOLT
M10 X 20mm HEX HEAD BOLT
M5 X 10mm FLAT HEAD MACHINE SCREW
M4 X 10mm MACHINE SCREW
M8 NYLON LOCKNUT
M12 NYLON LOCKNUT
SHOULD YOU REQUIRE ANY ASSISTANCE REGARDING THIS PRODUCT PLEASE CONTACT YORK DIRECTLY
YORK G510 / 30
PARTS LIST
5630-64
5630-65
5630-66
5630-67
5630-68
5630-69
5630-70
5630-71
5630-72
5630-73
5630-74
5630-75
5630-76
5630-77
5630-78
5630-79
5630-48
5630-49
5630-50
5630-51
5630-52
5630-53
5630-54
5630-55
5630-56
5630-57
5630-58
5630-59
5630-60
5630-61
5630-62
5630-63
5630-80
5630-81
5630-82
5630-83
5630-84
5630-99
5630-93
5630-100
5630-101
5630-89
5630-95
5630-96
5630-97
5630-98
KEY NO. PART NO. Q'TY(PCS) DESCRIPTION
76
77
78
79
72
73
74
75
68
69
70
71
64
65
66
67
60
61
62
63
56
57
58
59
52
53
54
55
48
49
50
51
88
89
90
91
92
93
84
85
86
87
80
81
82
83
2
2
2
4
1
2
2
1
6
2
2
2
4
2
1
2
1
1
3
9
1
1
1
SET
4
2
10
2
2
2
29
60
2
4
1
3
4
1
1
1
34
1
1
18
2
1
M10 NYLON LOCKNUT
M10 X 23mm X 2mm FLAT WASHER
M10 X 38mm X 2mm FLAT WASHER
M12 X 25mm X 2mm FLAT WASHER
M8 X 16mm X 2mm FLAT WASHER
M8 X 28mm X 2mm FLAT WASHER
PULLEY WHEEL SPACER ( t = 11.5mm )
PULLEY WHEEL SPACER ( t = 8.5mm )
PULL PIN / M10 X 65mm ROUND HEAD
ROUND HEAD PULL PIN / M10 X 30mm
HAND WHEEL KNOB
CHAIN ( 12 LINKS )
SNAP HOOK ( Φ8 X 80mm )
5 KG WEIGHT PLATE / 260mm X 130mm X 25mm
TOP PLATE / 210mm X 100mm X 94.5mm
TOP PLATE FIXING BOLT / M12 X 40mm
SELECT PIN / Φ10 X 116mm X 44mm
PLASTIC BOLT CAP / 19 X 19
OIL BEARING / Φ38mm X Φ25mm X 18mm
OIL BEARING / Φ28.5mm X Φ15.88mm X 10.5mm
OIL BEARING / Φ25mm X Φ12mm X 15mm
50mm X 75mm INTERNAL END CAP ( t = 1.5mm )
45mm SQ. INTERNAL END CAP ( t = 1.5mm )
45mm SQ. INTERNAL END CAP ( t = 2mm )
Φ25.4mm INTERNAL END CAP ( t = 2mm )
Φ25.4mm INTERNAL END CAP / ROUND HEAD
Φ45mm X 25mm RUBBER BUMPER
Φ63.5mm X 25mm RUBBER BUMPER
Φ25mm X 8mm RUBBER BUMPER
Φ31.8mm X 125mm HAND GRIP
Φ12mm X 110mm SLEEVE
LEG FOAM ROLLER / 90mm X 180mm
ARM FOAM ROLLER / 100mm X 550mm
SEAT UPHOLSTERY
BACK REST UPHOLSTERY
PULLEY WHEEL ASSEMBLY / 90mm OD.
PULLEY WHEEL COVER
LOW PULL CABLE / 3850mm LONG
PEC DEC CABLE / 1780mm LONG
CONNECTING CABLE / 3135mm LONG
LAT PULL CABLE / 3025mm LONG
50mm X 75mm INTERNAL END CAP ( t = 2mm )
SQUARE PULLEY FIXING PLATE
10mm X 35mm X M8 FEMALE SCREW BOLT
M8 X 15mm MALE SCREW BOLT
HOOK PULLEY BRACKET
SHOULD YOU REQUIRE ANY ASSISTANCE REGARDING THIS PRODUCT PLEASE CONTACT YORK DIRECTLY
YORK G510 / 31
F I T N E S S
PLACE
STAMP
HERE
PLACE
STAMP
HERE
PLACE
STAMP
HERE
advertisement