Eden PACK SOLO Technical Manual

PACK SOLO

Standalone Biometric reader

Access control

Technical manual

Technical manual PACKSOLO

– V1.5

Contents

Contents ......................................................................................................................... 2

Warning .......................................................................................................................... 3

Acknowledgement ......................................................................................................... 4

Information and recommendations .............................................................................. 5

Technical characteristics .............................................................................................. 6

1) Biometric reader ...................................................................................................... 6

2) Remote control opening .......................................................................................... 6

Wiring diagram ............................................................................................................... 7

3) Connecting the reader to the control module .......................................................... 7

4) Connecting to a third party intrusion control unit ..................................................... 8

5) Connecting an exit push button and a door contact ................................................ 8

6) Switch configuration ................................................................................................ 9

7) Power failure door activator .................................................................................. 10

8) Electromagnetic door lock triggered by a power failure ......................................... 10

9) Standard door activator: triggered by a voltage pulse ........................................... 11

Initial power-on – Factory configuration .................................................................... 12

Installation of more than one reader on the same site ............................................. 13

User management ........................................................................................................ 14

1) Add a user with a badge plus fingerprint ............................................................... 14

2) Add a user with badge only ................................................................................... 15

3) Add user with a fingerprint only ............................................................................. 15

4) Add an “Alarm” user with a badge and fingerprint ................................................. 16

5) Add an “Alarm” user with fingerprint only .............................................................. 17

6) Deleting a badge ................................................................................................... 17

7) Deleting a user with fingerprint only ...................................................................... 18

8) Deleting all users (fingerprints and badges only) .................................................. 18

Restore to factory settings ......................................................................................... 19

Signaling LEDs ............................................................................................................ 20

Connector blocks ........................................................................................................ 21

Check list ...................................................................................................................... 22

Notes ............................................................................................................................. 23 p.2/24

Warning

Technical manual PACKSOLO

– V1.5

Caution: This product is designed to work only in a standalone mode p.3/24

Technical manual PACKSOLO

– V1.5

Acknowledgement

Dear client,

You have just purchased a “

PACKSOLO

” reader with remote control opening built by the

French company EDEN INNOVATIONS.

The entire EDEN INNOVATIONS team would like to thank you for your interest as well as your confidence in our security solution.

We hope that you will be completely satisfied with the level of security it provides for your com pany’s premises.

Should you have any comments, please contact us via our web site at www.eden-innovations.com

The EDEN INNOVATIONS team. p.4/24

Technical manual PACKSOLO

– V1.5

Information and recommendations

p.5/24

 Pursuant to European directive UTE C00-200, incorporating directives 89/336 EEC and

92/31 EEC, PACKSOLO complies with the following standards:



NF EN 50081-1 governing electromagnetic radiation, and



NF EN 50082-1 governing electromagnetic susceptibility.

 Cabling recommendations: the cables used to connect readers, the network and other peripherals must be installed in accordance with the instructions for Level 2 (protected environment) of standard NF EN 61000-4-4.

 This product must be installed by an approved company.

Incorrect installation and usage may result in electric shock or fire. Before installing the product, read the technical information and comply with the recommendations.

 Once the power is turned off, all the internal capacitors will discharge themselves to a safe level after 60 seconds under normal conditions. However, in the event of a power failure, the charge may be maintained for much longer and suitable precautions should be taken before handling the product.

Technical manual PACKSOLO

– V1.5

Technical characteristics

1) Biometric reader

Maximum power consumption ........ 300mA @12V

Power supply voltage ...................... 9

– 14VDC

Weight ............................................. 175 g

Housing dimensions ........................ 119 x 77 x 40 mm

Operating temperature .................... - 20°C to + 50°C

........................................................ - 4°F to +122°F

Fingerprints ..................................... 500 templates

2) Remote control opening

Maximum power consumption ........ 200mA @12V

Power supply voltage ...................... 9 – 14VDC

Weight ............................................. 200g

Housing dimensions ........................ 77 x 55 x 25 mm

Operating temperature .................... - 20°C to + 50°C

........................................................ - 4°F to +122°F

Control relay .................................... 1A / 12V – 1A / 24V

Transistored output ......................... 100mA/active at 0V p.6/24

Technical manual PACKSOLO

– V1.5

Wiring diagram

3) Connecting the reader to the control module

Data sheet:

12 V DC power supply

4 wires (3 pairs recommended)

Ø

1200 m (2730 ft)

0.6 mm (1/30 in) (SYT recommended)

Characteristic: Sensitive connection

Screen: Mandatory

To achieve 1200 m (2730 ft), you need to install a 120



resistor at each end of the network between points A and B (see above).

Note: The total length must not exceed the recommended distance. p.7/24

Technical manual PACKSOLO

– V1.5

4) Connecting to a third party intrusion control unit

Commutator outputs open

Third party intrusion control unit

Input: intrusion trigger

Input: “activation”

Output: “Status of the control unit”

Note: To connect a third party intrusion control unit, ensure that a common earth is connected between the control module and the control unit.

Input: dry contact:

If the input is set to 0V: The alarm is activated

(opening impossible, mandatory inactivation of the alarm before opening, using an alarm fingerprint or manually)

5) Connecting an exit push button and a door contact

Intrusion trigger p.8/24

Press button

Technical manual PACKSOLO

– V1.5

6) Switch configuration

The control module has 3 configuration switches:

 Switches 1 and 2: configuration of the time delay for the opening control

Bistable mode

5 seconds

10 seconds

20 seconds



Switch 3: configuration of the “Alarm activation/inactivation” output

(activation/inactivation of a third party intrusion control unit)

Bistable mode

Impulsion 1 second p.9/24

Technical manual PACKSOLO

– V1.5 p.10/24

7) Power failure door activator

Non-return diode

12V 0V

Power supply

Note: In order to avoid any random malfunctions that may interfere with the correct use of the system caused by return currents, it is essential to use and connect the non-return diodes supplied with the product in accordance with the wiring diagram above.

Even when using an additional backed-up power supply for locking, which is separate from the reader's power supply, it is obligatory to follow the wiring diagram above.

8) Electromagnetic door lock triggered by a power failure

Non-return diode

12V 0V

Power supply

Note: In order to avoid any random malfunctions that may interfere with the correct use of the system caused by return currents, it is essential to use and connect the non-return diodes supplied with the product in accordance with the wiring diagram above.

Even when using an additional backed-up power supply for locking, which is separate from the reader's power supply, it is obligatory to follow the wiring diagram above.

Technical manual PACKSOLO

– V1.5 p.11/24

9) Standard door activator: triggered by a voltage pulse

Non-return diode

+12V 0V

Power supply

Note: In order to avoid any random malfunctions that may interfere with the correct use of the system caused by return currents, it is essential to use and connect the non-return diodes supplied with the product in accordance with the wiring diagram above.

Even when using an additional backed-up power supply for locking, which is separate from the reader’s power supply, it is obligatory to follow the wiring diagram above.

Technical manual PACKSOLO

– V1.5 p.12/24

Initial power-on – Factory configuration

When you first start the product, you need to register the 3 configuration cards ( Add , Add Alarm and Delete ) with the reader in order to activate it. To do this, follow the procedure below:

( blue and green LEDs blink alternately) Present the

Add badge

After this stage, your product is activated.

Present the

Add Alarm badge

(

Present the

Delete

Blue

badge

LED blink)

Technical manual PACKSOLO

– V1.5 p.13/24

Installation of more than one reader on the same site

If you use the badge with fingerprint access for several readers on the same site, so as to remember the same code for each reader (therefore to not repeat the addition of badges on each reader), you must only use one set of configuration badges for all readers on the same site.

Reader 1

Reader 2

Reader 3

Technical manual PACKSOLO

– V1.5

User management

1) Add a user with a badge plus fingerprint

Present the Add badge at the same time as the badge for the user you wish to add

You have 10 seconds to present the second finger of the user to be added 3 times (if you only want to enrol one finger, wait for 10 seconds) p.14/24

You have 10 seconds to present the first finger of the user to be added 3 times

Present the badge for the user that you want to add again and wait for the enrolment confirmation BEEP

Technical manual PACKSOLO

– V1.5 p.15/24

2) Add a user with badge only

Present the Add badge at the same time as the badge for the user you want to add

3) Add user with a fingerprint only

Wait 10 seconds Present the badge for the user that you want to add again and wait for the enrolment confirmation BEEP

Present the Add badge You have 10 seconds to present

3 times the first finger of the user to be added

You have 10 seconds to present 3 times the second finger of the user to be added (if you only want to enrol one finger, wait for 10 seconds)

Technical manual PACKSOLO

– V1.5 p.16/24

4) Add an “Alarm” user with a badge and fingerprint

Note: An “Alarm” user can, by presenting his/her second fingerprint, activate or inactivate a third party alarm system.

Present the Add Alarm badge at the same time as the badge for the user you want to add

You have 10 seconds to present the access finger of the user to be added 3 times

You have 10 seconds to present the alarm finger of the user to be added 3 times (if you do not enrol a second fingerprint, the badge added will be encrypted as for a standard user – without an alarm function)

Present the badge for the user that you want to add again and wait for the enrolment confirmation BEEP

Technical manual PACKSOLO

– V1.5

5) Add an “Alarm” user with fingerprint only

Present the badge

6) Deleting a badge

Add Alarm You have 10 seconds to present the access finger of the user to be added 3 times

You have 10 seconds to present the alarm finger of the user to be added

3 times (if you do not enrol a second fingerprint, the user added will not have an alarm function)

Present the Delete p.17/24

badge at the same time as the badge for the user you want to delete then wait for the confirmation BEEP

Technical manual PACKSOLO

– V1.5

7) Deleting a user with fingerprint only p.18/24

Present the badge

Delete

You have 10 seconds to present one of the 2 fingers of the user to be deleted. If the user is recognised, he/she will immediately be deleted

8) Deleting all users (fingerprints and badges only)

Present the Delete badge and leave it in front of the reader for 10 seconds then wait for the confirmation BEEP

Technical manual PACKSOLO

– V1.5 p.19/24

Restore to factory settings

Switch off the power

Note : Should you lose your configuration badges, you need to reset the reader to its factory settings in order to register a new set of configuration badges. This process will delete all the users (fingerprints only and badges).

To restore to factory settings:

Press the

RESET button and hold it down while switching the power back on

Wait for 10 seconds

After 10 seconds, the green and blue

LEDs will flash alternately, now proceed with activation

Technical manual PACKSOLO

– V1.5 p.20/24

Signaling LEDs

An explanation of the different status of the blue and green LEDs:

Blue LED Green LED Reader status

Flashing alternately

Flashing Off

Reader in factory configuration: waiting for configuration badges/cards ( Add , Add Alarm , Delete )

Normal operation: waiting for a user

-

On

On

-

Door open

Alarm activated: Refusing “standard” users and waiting for inactivation of the alarm (alarm fingerprint or manual inactivation)

The fingerprint sensor is off when no fingerprint is stored. The fingerprint is on (red) when at least one fingerprint is stored.

Technical manual PACKSOLO

– V1.5

Connector blocks

p.21/24

Technical manual PACKSOLO

– V1.5

Check list

Pack SOLO



Serial number



ID number



Gasket



Torx bit



Torx screw



Bag



Wall seal

:

:

:

:

:

:

: p.22/24

Technical manual PACKSOLO

– V1.5 p.23/24

Notes

-------------------------------------------------------------------------------------------------------------------------------

-------------------------------------------------------------------------------------------------------------------------------

-------------------------------------------------------------------------------------------------------------------------------

-------------------------------------------------------------------------------------------------------------------------------

-------------------------------------------------------------------------------------------------------------------------------

-------------------------------------------------------------------------------------------------------------------------------

-------------------------------------------------------------------------------------------------------------------------------

-------------------------------------------------------------------------------------------------------------------------------

-------------------------------------------------------------------------------------------------------------------------------

-------------------------------------------------------------------------------------------------------------------------------

-------------------------------------------------------------------------------------------------------------------------------

-------------------------------------------------------------------------------------------------------------------------------

-------------------------------------------------------------------------------------------------------------------------------

-------------------------------------------------------------------------------------------------------------------------------

-------------------------------------------------------------------------------------------------------------------------------

-------------------------------------------------------------------------------------------------------------------------------

-------------------------------------------------------------------------------------------------------------------------------

-------------------------------------------------------------------------------------------------------------------------------

-------------------------------------------------------------------------------------------------------------------------------

-------------------------------------------------------------------------------------------------------------------------------

-------------------------------------------------------------------------------------------------------------------------------

-------------------------------------------------------------------------------------------------------------------------------

-------------------------------------------------------------------------------------------------------------------------------

-------------------------------------------------------------------------------------------------------------------------------

Technical Support: [email protected]

Zone Commerciale et Artisanale

670, route de Berre

13510 EGUILLES

France www.eden-innovations.com