Buy parts on line at https://Dynashop.co.uk/ for all things Dynabrade
Air Tools For The Body Shop
Model:
18180
AUTOMOTIVE
Parts Page Reorder No. APD01•05
Effective March, 2001
3" Disc Sander
.5 Hp/7˚
Air Motor and Machine Parts
!
WARNING
Always operate, inspect and maintain this tool in accordance with the Safety Code for portable air tools
(ANSI B186.1) and any other applicable safety codes and regulations. Please refer to Dynabrade’s
Warning/Safety Operating Instructions for more complete safety information.
Index Key
No. Part Description
1 50113 Roloc ® Pad
2 18864 Lock Ring
3 18863 Silencer
4 18862 Air Control Ring
5 18861 Rotor Nut
6 18428 Bearing
7 18826 Front End Plate
8 18821 Pin
9 18825 Rotor Spacer
10 18870 Rotor
11 18823 Rotor Blade (4/pkg.)
12 18822 Cylinder
13 18820 Rear End Plate
14 18819 Bearing
15 18869 Gasket
16 18865 7˚ Housing
17 18867 Plug
18 18446 Lock Ring
19 18866 Washer
20 18400 Housing
21 18420 Valve Screw
22 18419 O-Ring
23 18418 O-Ring
24 18417 Regulator
25 18416 Spring
26 18415 O-Ring
27 18413 Valve Stem
28 18414 O-Ring
29 18412 Valve Bushing
30 18411 Stop Rod
31 18410 Safety Lever Spring
32 18408 Throttle Lever
33 18409 Spring Pin
34 18407 Lever Pin
35 18403 O-Ring
36 18868 Exhaust Plug
37 18405 Air Inlet
38 18439 Filter
23 N•m T
1
2
16
23 N•m T
4
3
7
23 N•m T
18
17
8
9
5
19
T 23 N•m
10
20
Left Hand Treads
6
22
24
26
28
11
29
12
8
13
21
23
25
27
30
14
23 N•m T
31
15
35
36
O
1
37
A
8
38
34
33
KEY
O
Oil: O
1
= Air Lube 32
G
Grease: G
1
= Lubriplate 630AA
A Adhesive: A
2
= Loctite #271
T Torque: N•m x 8.85 = In. - lbs.
Buy parts on line at https://Dynashop.co.uk/ for all things Dynabrade
Buy parts on line at https://Dynashop.co.uk/ for all things Dynabrade
Autobrade Red Important Operating, Maintenance and Safety Instructions
Carefully read all instructions before operating or servicing any Dynabrade ® Abrasive Power Tool.
Warning: Hand, wrist and arm injury may result from repetitive work motion and overexposure to vibration.
Important: All Dynabrade air tools must be used with a Filter-Regulator-Lubricator to maintain all warranties.
Operating Instructions:
Warning: Eye, face, respiratory, sound and body protection must be worn while operating power tools. Failure to do so may result in serious injury or death.
Follow safety procedures posted in workplace.
1.
With power source disconnected from tool, securely fasten abrasive/accessory on tool.
2.
Install air fitting into inlet bushing of tool. Important: Secure inlet bushing of tool with a wrench before attempting to install the air fitting to avoid damaging valve body housing.
3.
Connect power source to tool. Be careful not to depress throttle lever in the process.
4.
Check tool speed with tachometer. If tool is operating at a higher speed than the RPM marked on the tool or operating improperly, the tool should be serviced to correct the cause before use.
Maintenance Instructions:
1.
Check tool speed regularly with a tachometer. If tool is operating at a higher speed than the RPM marked on the tool, the tool should be serviced to correct the cause before use.
2.
Some silencers on air tools may clog with use. Clean and replace as required.
3.
All Dynabrade rotary vane style air motors should be lubricated. Dynabrade recommends one drop of air lube per minute for each 10 SCFM (example: if the tool specifications state 40 SCFM, set the drip rate of your filter-lubricator at 4 drops per minute).
Dynabrade Air Lube (P/N 95842 : 1pt. 473ml.) is recommended.
4.
An Air Line Filter-Regulator-Lubricator must be used with this air tool to maintain all warranties. Dynabrade recommends the following: 11405 Air Line
Filter-Regulator-Lubricator — Provides accurate air pressure regulation, two-stage filtration of water contaminants and micro-mist lubrication of pneumatic components. Operates 40 SCFM @ 100 PSI has 3/8" NPT female ports.
5.
Use only genuine Dynabrade replacement parts. To reorder replacement parts, specify the Model # , Serial # , and RPM of your machine.
6.
Mineral spirits are recommended when cleaning the tool and parts. Do not clean tool or parts with any solvents or oils containing acids, esters, keytones, chlorinated hydrocarbons or nitro carbons.
Safety Instructions:
Products offered by Dynabrade should not be converted or otherwise altered from original design without expressed written consent from Dynabrade, Inc.
• Important: User of tool is responsible for following accepted safety codes such as those published by the American National Standards Institute (ANSI).
• Operate machine for one minute before application to workpiece to determine if machine is working properly and safely before work begins.
• Always disconnect power supply before changing abrasive/accessory or making machine adjustments.
• Inspect abrasives/accessories for damage or defects prior to installation on tools.
• Please refer to Dynabrade’s Warning/Safety Operating Instructions Tag (Reorder No. 95903 ) for more complete safety information.
• Warning: Hand, wrist and arm injury may result from repetitive work, motion and overexposure to vibration.
Autobrade Red Tool Warranty
Following the reasonable assumption that any inherent defect which might prevail in a product will become apparent to the user within 6 months from the date of purchase, “Autobrade Red” tools are warranted against defects in workmanship and materials under normal use and service.
We shall, at our option, repair or replace at our factory, any “Autobrade Red” tool which shall, within 6 months after delivery to the original purchaser, indicate upon our examination to have been defective.
Our obligation is contingent upon proper use of “Autobrade Red” tools in accordance with factory recommendations, instructions and practices.
The warranty shall not apply in these cases:
1. Normally wearable parts such as bearings, rotor blades, etc.
2. Consumables such as sanding pads, etc.
3. Misuse, neglect in maintaining tool or tool modification.
4. Lack of lubrication or evidence of rust, dirt or corrosion.
5. Tools requiring normal tune-up or cleaning.
6. Tools being used after they are badly worn such as using ratchet with worn yoke.
7. Ratchets, anvils damaged by excessive hand torquing.
8. Use in production-type applications.
Products to be considered for warranty must be sent back to our factory, transportation prepaid by the user. Please send tool back to attention of
“Repair Department” with note fully explaining the nature of the problem along with a copy of original invoice indicating model and serial number.
Return product to:
Dynabrade, Inc.
Attn: Repair Department
8989 Sheridan Dr.
Clarence, NY 14031
Visit our Web Site: www.dynabrade.com
Air Tools For The Body Shop
DYNABRADE
®
DYNABRADE Automotive Aftermarket 8989 Sheridan Drive • Clarence, NY 14031-1490 • Phone: (716) 631-0100 • Fax: 716-631-2073
© DYNABRADE, INC., 2001 PRINTED IN USA
Buy parts on line at https://Dynashop.co.uk/ for all things Dynabrade
