01CPX385/EN最終  02.11.7 4:15 PM  ページ 1

LCD Projector CP-X385W

USER'S MANUAL

Vol.1 (Basic)

Thank you for purchasing this projector.

WARNING • Please read the accompanying manual “SAFETY

INSTRUCTIONS” and this “USER'S MANUAL” thoroughly to ensure correct usage through understanding. After reading, store this instruction manual in a safe place for future reference.

NOTE

• The information in this manual is subject to change without notice.

• The manufacturer assumes no responsibility for any errors that may appear in this manual

• The reproduction, transmission or use of this document or contents is not permitted without express written authority.

TRADEMARK ACKNOWLEDGEMENT :

• PS/2, VGA and XGA are registered trademarks of the International Business Machines Corporation.

• Apple, Mac and ADB are registered trademarks of Apple Computer, Inc.

• VESA and SVGA are trademarks of the Video Electronics Standard Association.

• Windows is a registered trademark of Microsoft Corporation.

• All other trademarks are the property of their respective owners.

CONTENTS

Page

PROJECTOR FEATURES ................2

PREPARATIONS ..............................2

PART NAMES ...................................4

SETTING UP

THE PROJECTOR ............................6

CONNECTING

YOUR DEVICES................................8

USING THE REMOTE

CONTROL .......................................13

TURNING ON THE POWER ...........14

TURNING OFF THE POWER .........16

ADJUSTING THE VOLUME ...........17

TEMPORARILY MUTING

THE SOUND....................................17

ADJUSTING THE POSITION..........18

USING THE AUTOMATIC

ADJUSTMENT FEATURE ..............19

Page

CORRECTING KEYSTONE

DISTORTIONS ................................20

USING THE MAGNIFY

FEATURE........................................21

FREEZING THE SCREEN ..............21

SIGNAL SEARCHING.....................22

SELECTING THE ASPECT

RATIO..............................................22

TEMPORARILY BLANKING

THE SCREEN..................................22

USING THE MENU

FUNCTIONS....................................23

OPERATING THE PC SCREEN .....24

THE LAMP ......................................25

THE AIR FILTER.............................27

THE HANDLE..................................29

OTHER CARE .................................29

1

01CPX385/EN最終  02.11.7 4:15 PM  ページ 2

PROJECTOR

FEATURES

This liquid crystal projector is used to project various computer signals as well as NTSC / PAL /

SECAM video signals onto a screen. Little space is required for installation and large images can easily be realized.

●

Keystone Distortion Correction

Quick correction of distorted images electrically

●

Ultra High Brightness

Crisp, ultra-bright presentations is achieved by using a UHB (ultra high brightness) lamp and a highly efficient optical system

●

Partial Magnification Function

Interesting parts of images can be magnified for closer viewing

●

Whisper Mode Equipped

Special mode is available for reducing projector noise to achieve quieter operation

PREPARATIONS

Your projector should come with the items shown below. Check to make sure that all the items are included. Contact your dealer if anything is missing.

NOTE • Keep the original packing material for future reshipment.

2

Power cord

(US Type)

Power cord

(UK Type)

Power cord

(Europe Type)

Projector

(with Lens Cap)

Liquid Crystal Projector

CP-X385W

ENGLISH

USER'S MANUAL Vol.1 Basic

Please read this user's manual thoroughly to ensure correct usage through understanding.

BEDIENUNGSANLEITUNG Teil 1 Grundlagen

Bitte lessen Sie diese Benutzerhandbuch zugunsten der korrekten Bedienung aufmerksam.

MANUEL D'UTILISATION Vol.1 Fondements

Nous vous recommandons de lire attentivement ce manuel pour bien assimiler le fonctionnement de l'appareil.

MANUALE D'ISTRUZIONI Vol.1 Informazioni di base

Vi preghiamo voler leggere attentamente il manuale d'istruzioni in modo tale da poter comprendere quanto riportato ai fini di un corretto utilizzo del proiettore.

MANUAL DE USUARIO Vol.1 Básico

Lea cuidadosamente este manual del usuario para poder utilizar corretamente el producto.

GEBRUIKSAANWIJZING Vol.1 Basis

Lees voor het qebruik alstublieft deze handleiding aandachtig door, om volledig profijt te hebben van de uitgebreide mogelijkheden.

BRUKERHÅNDBOK Vol.1 Grunnleggende

Vennligst les denne bruksanvisningen grundig for å være garantert driftssikker bruk.

INSTRUÇÕES DO PROPRIETÁRIO Vol.1 Básico

Para assegurar o uso correto do equipamento, por favor leia atentamente este manual do utilizador.

DEUTSCH

FRANÇAIS

ITALIANO

ESPAÑOL

NEDERLANDS

NORSK

PORTGÊS

中 文

REGULATORY

NOTICES

User's Manuals

(Vol.1/Vol.2)

Safety Instructions

Carrying Bag

RGB cable

Handle

Video/Audio cable Mouse cable

(PS/2)

STANDBY/ON

LASER

BLANK

VIDEO RGB

Two AA batteries

(for the remote control)

AUTO

MENU KEYSTONE

ENTER

POSITION

RESET

ASPECT FREEZE ESC

MAGNIFY

ON OFF

MUTE

VOLUME

SEARCH

Remote Control

Transmitter

01CPX385/EN最終  02.11.7 4:15 PM  ページ 3

WARNING Precautions to observe in regards to the power cord: Please use extra caution when connecting the projector's power cord as incorrect or faulty connections may result in FIRE AND/OR ELECTRICAL SHOCK. Please adhere to the following safety guidelines to insure safe operation of the projector:

• Only plug the power cord into outlets rated for use with the power cord's specified voltage range.

• Only use the power cord that came with the projector.

• NEVER ATTEMPT TO DEFEAT THE GROUND CONNECTION OF THE THREE-

PRONGED PLUG!

• Make sure that you firmly connect the power cord to the projector and wall outlet.

1

Connect your devices to the projector

Connect your computer, VCR and/or other devices you will be using to the projector.

8 〜 12

2

Insert the batteries into the remote control

13

3

Connect the power cord

(1) Connect the connector of the electrical power cord to the AC inlet of the main unit.

(2) Firmly plug the power cord's plug into the outlet

Power outlet

(2)

Power cord

(1)

AC inlet

3

01CPX385/EN最終  02.11.7 4:15 PM  ページ 4

PART NAMES

Speaker

Handle Hook

29

Power Switch 14

AC Inlet

(to the Power Cord)

3

Ventilation Openings

(Intake)

THE PROJECTOR

Indicates the corresponding reference page

15

15

Zoom Ring

Focus Ring

13

Remote Control

Sensor

Lens

14 Lens Cap

6

Foot Adjuster

STANDBY/ON Button

KEYSTONE Button

14

20

Foot Adjuster Button 6

Filter Cover 27

( ) for the Cooling Fan

Rear Foot Adjuster

6

4

S-VIDEO Port 11

COMPONENT VIDEO

Y Port

C B /P B Port

C R /P R Port

11

11

11

VIDEO IN Port 11

AUDIO IN R Port 11

AUDIO IN L Port 11

AUDIO IN 1 Port 10

AUDIO IN 2 Port 10

AUDIO OUT Port

9

1 RGB IN 2

AUDIO IN VIDEO IN S-VIDEO IN

AUDIO

IN

1 2 AUDIO OUT USB

RGB OUT CONTROL

TERMINAL PANEL

15

26

INPUT Button

LAMP Indicator

27

14

TEMP Indicator

POWER Indicator

18

23

RESET Button

MENU Button

Ventilation Openings

(exhaust)

13

10

Remote Control

Sensor

RGB IN 1 Port

10

RGB IN 2 Port

10 CONTROL Port

12 RGB OUT Port

10 USB Port

01CPX385/EN最終  02.11.7 4:15 PM  ページ 5

THE REMOTE CONTROL

STANDBY/ON button

14

VIDEO button 15

STANDBY/ON

LASER

BLANK

VIDEO RGB

Disk Pad 24

AUTO button 19

MENU button 23

, , ,

Cursor buttons

23

POSITION button 18

ASPECT button 22

MAGNIFY button 21

AUTO

MENU KEYSTONE

ENTER

POSITION RESET

ASPECT FREEZE ESC

MAGNIFY

ON OFF

MUTE

VOLUME

SEARCH

5 LASER button

22 BLANK button

15 RGB button

24

MOUSE / RIGHT

Button

20 KEYSTONE button

23 ENTER button

18 RESET button

21 FREEZE button

23 ESC button

17 MUTE button

17 VOLUME button

22 SEARCH button

WARNING • The laser pointer of the remote control transmitter is used in place of a finger or rod. Never look directly into the laser beam outlet or point the laser beam at other people. The laser beam can cause vision problems.

AVOID EXPOSURE-

LASER RADIATIONS IS

EMITTED FROM THIS

APERTURE

C A U T I O N

LASER RADIATION-

DO NOT STARE INTO BEAM

MAX. OUTPUT: 1mW

WAVE LENGTH: 650nm

CLASS2 LASER PRODUCT

LASER RADIATION

DO NOT STARE INTO BEAM

CLASS2 LASER PRODUCT

MAX. OUTPUT: 1mW

WAVE LENGTH: 650nm

IEC60825-1 : 1993+A1:1997

Complies with 21 CFR 1040. 10 and 1040. 11 except for deviations pursuant to Laser Notice No.50, dated 2001.7.26

SMK CORPORATION

6-5-5 Togoshi Shinagawa-ku, Tokyo, JAPAN 142-8511

MANUFACTURED Novemver 2001

PLACE OF MANUFACTURER: A

NOTE • Keep the remote control transmitter away from children and pets.

• Do not give the remote control transmitter any physical impact. Take care not to drop.

• Do not place the heavy objects on the remote control transmitter.

• Do not wet the remote control transmitter or place it on any wet object.

• Do not place the remote control transmitter close to the cooling fan of the projector.

• Do not disassemble the remote control transmitter.

5

01CPX385/EN最終  02.11.7 4:15 PM  ページ 6

SETTING UP THE PROJECTOR

CAUTION • Install the projector in a suitable environment according to instructions of the accompanying manual “SAFETY INSTRUCTIONS” and this manual.

• If you press the elevator buttons without holding the projector, the projector might crash down, overturn, smash your fingers and possibly result in malfunction. To prevent damaging the projector and injuring yourself, ALWAYS HOLD THE

PROJECTOR whenever using the elevator buttons to adjust the elevator feet.

Angle Adjustment

Use the foot adjusters on the bottom of the projector to adjust the projection angle. It is variable within 0˚ to 9˚ approximately.

1

L i f t u p t h e f r o n t s i d e o f t h e projector, and pressing the foot a d j u s t e r b u t t o n , a d j u s t t h e projection angle.

Press the foot adjuster button

2

Release the button to lock at the desired angle.

3

Turn the rear foot adjuster to adjust the left-right slope. Do not force the foot adjuster screws. This could damage the adjusters or cause the lock to fail.

Rear Foot Adjuster

6

01CPX385/EN最終  02.11.7 4:15 PM  ページ 7

Adjusting the Screen Size and Projection Distance

Refer to the illustrations and tables below to determine the screen size and projection distance.

The values shown in the table are calculated for a full size screen a:Distance from the projector to the screen (±10%) b:Distance from the lens center to the bottom of the screen (±10%) c:Distance from the lens center to the top of the screen (±10%)

If 4:3 aspect ratio

4

3

Top View a

Side View

Screen size

[inches (m)]

40 (1.0)

60 (1.5)

80 (2.0)

100 (2.5)

120 (3.0)

150 (3.8)

200 (5.0) a [inches (m)]

Min.

62 (1.6)

94 (2.4)

Max.

82 (2.1)

123 (3.1)

127 (3.2)

160 (4.1)

192 (4.9)

241 (6.1)

323 (8.2)

164 (4.2)

205 (5.2)

246 (6.3)

308 (7.8)

411 (10.4)

7

01CPX385/EN最終  02.11.7 4:15 PM  ページ 8

CONNECTING YOUR DEVICES

Devices You Can Connect to the Projector

(Refer to this section for planning your device configuration to use for your presentation.)

CAUTION • Incorrect connecting could result in fire or electrical shock. Please read this manual and the separate “SAFETY INSTRUCTIONS”.

ATTENTION Precautions to observe when connecting other devices to the projector

• Whenever attempting to connect other devices to the projector, please thoroughly read the manual of each device to be connected.

• TURN OFF ALL DEVICES prior to connecting them to the projector. Attempting to connect a live device to the projector may generate extremely loud noises or other abnormalities that may result in malfunction and/or damage to the device and/or projector. Refer to the “TECHNICAL” of the USER’S MANUAL (Vol.2) for the pin assignment of connectors and RS-232C communication data.

• Make sure that you connect devices to the correct port. Incorrect connection may result in malfunction and/or damage to the device and/or projector.

• A component cable and some other cables have to be used with core set. Use the accessory cable or a designated-type cable for the connection. For cables that have a core only at one end, connect the core to the projector.

• Secure the screws on the connectors and tighten.

Indicates the corresponding reference page

12 Display monitors

11 DVD players

11 VCRs

10 Laptop computers

10 Desktop computers

8

01CPX385/EN最終  02.11.7 4:15 PM  ページ 9

Ports and Cables

Refer to the table below to find out which projector port and cable to use for connecting a given device. Use this table for determining which cables to prepare.

Function

RGB input

RGB output

Audio input

(from the computer)

USB mouse control

PS/2 mouse control

ADB mouse control

Serial mouse control

RS-232C communication

S-video input

Video input

Projector Port

RGB IN 1

RGB IN 2

RGB OUT

AUDIO IN 1

(interlocked with RGB IN 1)

AUDIO IN 2

(interlocked with RGB IN 2)

USB

CONTROL

Connection Cables

Accessory RGB cable or optional RGB cable with D-sub 15-pin shrink jack and inch thread screws

Optional audio cable with stereo mini jack

Optional USB cable

Accessory PS/2 mouse cable

Optional ADB mouse cable

Optional serial mouse cable

Optional RS-232C cable

Optional S-video cable with mini DIN 4-pin jack

Accessory audio/video cable

Component video input

Audio input

(from video equipment)

Audio output

S-VIDEO IN

VIDEO IN

COMPONENT VIDEO Y

COMPONENT VIDEO C

B

/P

B

COMPONENT VIDEO C

R

/P

R

AUDIO IN L

AUDIO IN R

AUDIO OUT

Optional component video cable

Accessory audio/video cable or optional audio cable with RCA jack

Optional audio cable with stereo mini jack

NOTE About Plug-and-Play Capability

• This projector is compatible with VESA DDC 1/2B. Plug-and-Play can be achieved by connecting this projector to computers that are VESA DDC (display data channel) compatible. Please take advantage of this function by connecting the accessory RGB cable to the RGB IN 1 port (DDC 1/2B compatible). Plug-and-Play may not work properly if any other type of connection is attempted.

• Plug-and-Play is a system composed of the computer, its operating system and peripheral equipment (i.e. display devices).

• Please use the standard drivers as this projector is a Plug-and-Play monitor.

• Plug-and-Play may not function properly with some type of computers. Use the RGB

IN 2 port if Plug-and-Play does not function correctly.

9

01CPX385/EN最終  02.11.7 4:15 PM  ページ 10

CONNECTING YOUR DEVICES (continued)

Connecting to a Computer

ATTENTION Whenever attempting to connect a laptop computer to the projector, be sure to activate the laptop's RGB external image output (set the laptop to CRT display or to simultaneous LCD and CRT display). For details on how this is done, please refer to the instruction manual of the corresponding laptop computer.

1

A

RGB IN 2

AUDIO IN VIDEO IN S-VIDEO IN

AUDIO

IN B

1 2 AUDIO OUT USB

B

RGB OUT CONTROL

A

USB cable

If connecting to a

USB port equipped computer

AUDIO IN VIDEO IN S-VIDEO IN

AUDIO

IN

1 2 AUDIO OUT

C

USB

D

1

RGB OUT

RGB IN 2

A

B

CONTROL

D C

A B

10

Laptop computer Desktop computer

NOTE

• Some computers may have multiple display screen modes. Use of some of these modes will not be possible with this projector.

• For some RGB input modes, the optional Mac adapter is necessary.

01CPX385/EN最終  02.11.7 4:15 PM  ページ 11

Connecting to a DVD Player

A A A

AUDIO IN VIDEO IN

AUDIO

IN

1 2 AUDIO OUT

S-VIDEO IN

B B B C

USB

A

1 RGB IN 2

RGB OUT

B

CONTROL

C

S-VIDEO cable

If using a S-video connection

If using a component  video connection

If using an audio/video  connection

DVD player

Connecting to a VCR

1 RGB IN 2

AUDIO IN VIDEO IN S-VIDEO IN

A A A B

AUDIO

IN

1 2 AUDIO OUT USB

A

RGB OUT

B

CONTROL

S-VIDEO cable

If using a S-video

connection

VCR

11

01CPX385/EN最終  02.11.7 4:15 PM  ページ 12

CONNECTING YOUR DEVICES (continued)

Connecting to a Display Monitor

1 RGB IN 2

AUDIO IN VIDEO IN S-VIDEO IN

AUDIO

IN

1 2 AUDIO OUT USB A

RGB OUT

A

CONTROL

Display monitor

12

01CPX385/EN最終  02.11.7 4:15 PM  ページ 13

USING THE REMOTE CONTROL

Putting batteries into the remote control unit

CAUTION Precautions to observe in regards to the batteries

Always handle the batteries with care and use them only as directed. Improper use may result in battery cracking or leakage, which could result in fire, injury and/or pollution of the surrounding environment.

• Keep the battery away from children and pets.

• Be sure to use only the batteries specified for use with the remote control. Do not mix new batteries with used ones.

• When inserting batteries, verify that the plus and minus terminals are aligned correctly (as indicated in the remote control).

• When you dispose the battery, you should obey the law in the relative area or country.

1

Remove the battery cover

Push the knob while lifting up the battery cover in the direction of the arrow.

2

Insert the batteries

Align and insert the two AA batteries (that came with the projector) according to their plus and minus terminals (as indicated in the remote control).

3

Close the battery cover

Replace the battery cover in the direction of the arrow and snap it back into place.

Operating the remote control

• The remote control works with both the projector's front and rear remote sensors.

• The range of the remote sensor on the front and back is 3 meters with a 60-degree range (30 degrees to the left and right of the remote sensor).

• Since the remote control uses infrared light to send signals to the projector (Class 1 LED), be sure to use the remote control in an area free from obstacles that could block the remote control's output signal to the projector.

30 degrees

30 degrees approximately

3 meters

30 degrees

30 degrees approximately

3 meters

• Only use the accompanying remote control. Using other remote controls (even of similiar models) to control the

CP-X385W may result in unexpected operation.

ATTENTION Precautions to observe when using the remote control

• Do not drop or otherwise expose the remote control to physical impact.

• Do not get the remote control wet or place it on wet objects. Doing so may result in malfunction.

• Remove the batteries from the remote control and store them in a safe place if you won't be using the remote control for an extended period.

• Replace the batteries whenever the remote control starts to malfunction.

• When strong light, such as direct sunlight or light from an extremely close range (such as from an inverter fluorescent lamp), hits the projector's remote sensor, the remote control may cease to function.

Adjust the direction of the projector to keep light from directly hitting the projector's remote sensor.

13

01CPX385/EN最終  02.11.7 4:15 PM  ページ 14

TURNING ON THE POWER

Precautions

Connect all devices to be used to the projector prior to turning on the power.

8

〜

12

WARNING When the power is ON, a strong light is emitted. Do not look into the lens.

STANDBY/ON

LASER

BLANK

VIDEO RGB

1

Make sure that the power cord is firmly and correctly connected to the projector and outlet

3

2

Turn on the projector's power

Set the power switch to [ | ] (ON). The projector will go to STANDBY mode and the POWER indicator will light to solid orange.

POWER-indikator

Control panel på/av-bryter

14

NOTE Turn the power on/off in right order.

• Power on the projector before the computer or video tape recorder.

• Power off the projector after the computer or video tape recorder.

3

Press the STANDBY/ON button (control panel or remote control)

• The projector begins warming up and the POWER indicator blinks green.

STANDBY/ON

• The POWER indicator stops blinking and lights to solid green once the projector's power is completely on.

4

Remove the lens cap

The picture is projected.

01CPX385/EN最終  02.11.7 4:15 PM  ページ 15

Selecting an Input Signal

5 Using the remote control

If selecting RGB input

Press the RGB button

Press this button to toggle between the devices connected to RGB IN 1 and 2.

As illustrated below, each time you press the RGB button, the projector switches between RGB IN 1 and 2.

Select the signal you wish to project.

RGB

RGB IN 1 RGB IN 2

Using the projector's control panel

Press the INPUT button

As illustrated below, each time you press the INPUT button, the projector switches between its input signal ports. Select the signal you wish to project.

INPUT

RGB IN 1 RGB IN 2 VIDEO IN

If selecting video input

Press the VIDEO button

Press this button to toggle between the devices connected to VIDEO IN, S-

VIDEO IN and COMPONENT VIDEO. As illustrated below, each time you press the VIDEO button, the projector switches between VIDEO IN, S-VIDEO

IN and COMPONENT VIDEO. Select the signal you wish to project.

VIDEO VIDEO IN S-VIDEO IN

COMPONENT VIDEO S-VIDEO IN

COMPONENT VIDEO

6

Use the zoom ring to adjust the screen size

7

Use the focus ring to focus the picture

15

01CPX385/EN最終  02.11.7 4:15 PM  ページ 16

TURNING OFF THE POWER

STANDBY/ON

LASER

BLANK

VIDEO RGB

1

Press the STANDBY/ON button (control panel or remote control)

The message "Power off?" will appear on the screen for approximately 5 seconds.

STANDBY/ON

AUTO

MENU KEYSTONE

ENTER

POSITION RESET

ASPECT FREEZE ESC

MAGNIFY

ON OFF

MUTE

VOLUME

2

Press the STANDBY/ON button again

(control panel or remote control)

Press the STANDBY/ON button again while the "Power off?" message is visible. The projector lamp goes off and starts cooling down. The POWER indicator blinks orange while the lamp cools down. (Pressing the STANDBY/ON button while the POWER indicator is blinking orange has no effect.)

The system goes into the STANDBY mode after cooling down and the POWER indicator stops blinking orange and then lights to solid orange.

STANDBY/ON

Control panel

3

Check that the POWER indicator stops blinking and lights to solid orange.

Switch the power switch to [O] (OFF).

POWER-indikator på/av-bryter

16

NOTE

• Except in emergencies, follow the abovementioned procedure for turning power off.

4

Confirm that the POWER indicator has gone off and then attach the lens cap.

When the projector has completed powering down, the

POWER indicator will go off.

01CPX385/EN最終  02.11.7 4:15 PM  ページ 17

ADJUSTING THE VOLUME

STANDBY/ON

LASER

BLANK

VIDEO RGB

1

Press the VOLUME button

As illustrated on the right, a dialog will appear on the screen to aid you in adjusting the volume.

VOLUME

AUTO

MENU KEYSTONE

ENTER

POSITION RESET

ASPECT FREEZE ESC

MAGNIFY

ON OFF

MUTE

VOLUME

SEARCH

VOLUME

16

2 Press the , buttons to adjust the volume

Press the VOLUME button again to close the dialog and complete this operation. (Even if you don't do anything, the dialog will automatically disappear after a few seconds.)

VOLUME

Press this to increase the volume

Press this to decrease the volume

16

TEMPORARILY MUTING THE SOUND

AUTO

MENU KEYSTONE

ENTER

POSITION RESET

ASPECT FREEZE ESC

MAGNIFY

ON OFF

MUTE

VOLUME

SEARCH

1

Press the MUTE button

As illustrated on the right, a dialog will appear on the screen indicating that you have muted the sound. Press the VOLUME button to close the dialog. (Even if you don't do anything, the dialog will automatically disappear after a few seconds.)

Press the MUTE button again to restore the sound.

VOLUME

MUTE

16

17

01CPX385/EN最終  02.11.7 4:15 PM  ページ 18

ADJUSTING THE POSITION

STANDBY/ON

LASER

BLANK

VIDEO RGB

1

Press the POSITION button

As illustrated on the right, a dialog will appear on the screen to aid you in adjusting the position.

POSITION

POSITION

AUTO

MENU KEYSTONE

ENTER

POSITION RESET

ASPECT FREEZE ESC

MAGNIFY

ON OFF

MUTE

VOLUME

SEARCH

2

Use the , , , buttons to adjust the position

When you want to initialize the position, press the RESET button during adjustment.

Press the POSITION button again to close the dialog and complete this operation. (Even if you don't do anything, the dialog will automatically disappear after a few seconds.)

This function is only available for RGB IN 1/2 input.

Control panel

18

01CPX385/EN最終  02.11.7 4:15 PM  ページ 19

USING THE AUTOMATIC ADJUSTMENT FEATURE

1

Press the AUTO button

AUTO STANDBY/ON

LASER

BLANK

VIDEO RGB

Automatic Adjustment for RGB Input

Horizontal position (H. POSIT), vertical position (V.

POSIT), clock phase (H. PHASE) and horizontal size (H.

SIZE) are automatically adjusted.

Make sure that the application window is set to its maximum size prior to attempting to use this feature.

Dark pictures may still be incorrectly adjusted. Use a bright screen when adjusting.

AUTO

MENU KEYSTONE

ENTER

POSITION RESET

ASPECT FREEZE ESC

MAGNIFY

ON OFF

MUTE

VOLUME

SEARCH

Automatic Adjustment for Video Input

The signal type best suited for the respective input signal is selected automatically.

This feature is available only if VIDEO is set to AUTO in the INPUT menu.

NOTE

The automatic adjustment operation requires approximately 10 seconds. Also, please note that it may not function correctly with some input signals.

19

01CPX385/EN最終  02.11.7 4:15 PM  ページ 20

CORRECTING KEYSTONE DISTORTIONS

STANDBY/ON

LASER

BLANK

VIDEO RGB

1

Press the KEYSTONE button

As illustrated on the right, a dialog will appear on the screen to aid you in correcting the distortion.

KEYSTONE KEYSTONE

KEYSTONE

16

2

Use the , buttons to select the direction of distortion to correct ( / )

AUTO

MENU KEYSTONE

ENTER

POSITION RESET

ASPECT FREEZE ESC

MAGNIFY

ON OFF

MUTE

VOLUME

SEARCH

3

Use the , buttons to correct the distortion

Press the KEYSTONE button again to close the dialog and complete this operation. (Even if you don't do anything, the dialog will automatically disappear after a few seconds.)

Control panel

20

NOTE

• This function may not be work well with some types of input signals.

• The adjustable range for correcting keystone distortions will vary with the type of input signal.

01CPX385/EN最終  02.11.7 4:15 PM  ページ 21

USING THE MAGNIFY FEATURE

STANDBY/ON

LASER

BLANK

VIDEO RGB

1

Press the MAGNIFY (ON) button

The projector enters MAGNIFY mode.

ON

2

Press the POSITION button, then use the , ,

, buttons to select the area to enlarge and then press the POSITION button again to confirm your selection

POSITION POSITION

AUTO

MENU KEYSTONE

ENTER

POSITION RESET

ASPECT FREEZE ESC

MAGNIFY

ON OFF

MUTE

VOLUME

SEARCH

3

Press the , buttons to zoom in and out of the selected area.

Press the MAGNIFY (OFF) button to exit MAGNIFY mode and restore the screen to normal. (The projector will also automatically exit MAGNIFY mode if there is a change in the input signal's state.)

NOTE

The projector will automatically exit from MAGNIFY mode if either the INPUT SELECT,

AUTO, ASPECT or VIDEO feature is used, or, if there is a change in the input signal's state.

FREEZING THE SCREEN

ENTER

POSITION

ASPECT FREEZE ESC

MAGNIFY

ON OFF

RESET

MUTE

1

Press the FREEZE button

The [II] icon appears and the screen will freeze at the current image. Press the FREEZE button again and the [ ] appears as the projector exits

FREEZE mode.

FREEZE

VOLUME

SEARCH

NOTE

• The projector will automatically exit from FREEZE mode if either the POSITION, VOLUME, MUTE, AUTO,

BLANK ON/OFF or MENU ON/OFF feature is used, or, if there is a change in the input signal's state.

• If the projector continues projecting the same image for a long time (i.e. you forget to exit FREEZE mode), the image might possibly remain as an afterimage. Do not leave the projector in FREEZE mode for too long.

21

01CPX385/EN最終  02.11.7 4:15 PM  ページ 22

SIGNAL SEARCHING

POSITION RESET

ASPECT FREEZE ESC

MAGNIFY

ON OFF

MUTE

VOLUME

SEARCH

1

Press the SEARCH button

When you press the SEARCH button, the projector begins searching for input signals. If it detects an input signal, the search will cease and the projector will project the detected signal. If the projector is unable to find an input signal at any of its ports, it will return to the state it was in prior to the search.

SEARCH

RGB IN 1 RGB IN 2 VIDEO IN

COMPONENT VIDEO S-VIDEO IN

SELECTING THE ASPECT RATIO

AUTO

MENU KEYSTONE

ENTER

POSITION RESET

ASPECT FREEZE ESC

MAGNIFY

ON OFF

MUTE

VOLUME

SEARCH

1

Press the ASPECT button

ASPECT

RGB IN 1, RGB IN 2, COMPONENT VIDEO

(HDTV signals : 1125i (1035i/1080i), 750p)

4:3 16:9

VIDEO IN, S-VIDEO IN, COMPONENT VIDEO

(Non-HDTV signals : 525i, 525p,625i)

4:3 16:9 SMALL

22

TEMPORARILY BLANKING THE SCREEN

STANDBY/ON

LASER

BLANK

VIDEO RGB

1

Press the BLANK button

The input signal screen is shut off, and a blank screen appears. You can set the blank screen using the menu

(from the SCREEN menu, select BLANK). Press the BLANK button again to remove the blank screen, and return to the input signal screen.

BLANK

AUTO

01CPX385/EN最終  02.11.7 4:15 PM  ページ 23

USING THE MENU FUNCTIONS

STANDBY/ON

LASER

BLANK

VIDEO RGB

1

Press the MENU button

MENU

The menu display appears on the screen. The projector has the following menus: MAIN,

PICTURE-1, PICTURE-2, INPUT, SCREEN, and

OPTION. Select a menu using the / buttons. The current settings of the items that can be manipulated via the selected menu appear.

AUTO

MENU KEYSTONE

ENTER

POSITION RESET

ASPECT FREEZE ESC

MAGNIFY

ON OFF

MUTE

VOLUME

2

Select a menu using the / buttons, then press the or ENTER button.

The display of the selected menu appears.

[ex. Adjusting SHARPNESS]

Use the the

/ buttons to select PICTURE-1, then press or ENTER button.

ENTER

MENU

MAIN

PICTURE-1

PICTURE-2

INPUT

SCREEN

OPTION

COLOR BAL R

COLOR BAL B

SHARPNESS

COLOR

TINT

–1

+1

–1

+1

–1

: SELECT

3

Select an item using the / buttons, then press the or ENTER button.

The operation display of the selected item appears. To adjust a numerical value, press the or ENTER button again to switch to the single menu (small display showing only the operation display area).

[ex. Adjusting SHARPNESS]

Use the press the

/ buttons to select SHARPNESS, then or ENTER button.

MENU

MAIN

PICTURE-1

PICTURE-2

INPUT

SCREEN

OPTION

COLOR BAL R

COLOR BAL B

SHARPNESS

COLOR

TINT

ENTER

0

: SELECT

4 Press the / buttons to adjust the level.

Press the MENU button to hide the menu and finish your operation. Alternatively, press the or ESC button to return to the previous display.

[ex. Adjusting SHARPNESS]

Use the / buttons to adjust the SHARPNESS.

23

01CPX385/EN最終  02.11.7 4:15 PM  ページ 24

OPERATING THE PC SCREEN

You can use the remote control as a simplified mouse or keyboard.

CAUTION Caution: Mistaken use of the mouse/keyboard control could damage your equipment.

• Only connect to a PC.

• Before connecting, read the manuals of the device you will connect.

• Do not plug or unplug the connector cables while the computer is operating.

STANDBY/ON

LASER

BLANK

VIDEO RGB

PS/2, ADB, Serial Mouse Control

1. Turn off the projector and PC power, and connect the projector’s

CONTROL terminal to the computer via the mouse cable.

2. If a USB cable is connected, disconnect it. If a USB cable is connected, the USB control function is given priority, and mouse control from the CONTROL terminal will not function.

3. Turn on the projector power, then the computer.

The functions in the table below can be controlled. If you have difficulty with control, restart the computer (either from the software or by pressing the restart button).

Available Functions

Move Pointer

Left click with mouse

Right click with mouse

Remote Control Operation

Use button

Press button

Press button

AUTO

MENU KEYSTONE

ENTER

POSITION RESET

ASPECT FREEZE ESC

MAGNIFY

ON OFF

MUTE

VOLUME

SEARCH

USB Mouse Control

1. Connect the projector’s USB terminal to the computer using a USB cable.

The functions in the table below can be controlled.

Available Functions

Move Pointer

Left click with mouse

Right click with mouse

Remote Control Operation

Use button

Press button

Press button

NOTES

• It may not be possible to control notebook PCs, and other computers with built-in pointing devices (e.g.

track balls), using this remote control. In this case, before connecting go into BIOS (system setup) and select external mouse, and disable the pointing devices. In addition, the mouse may not function if the computer does not have the needed utility program. See your computer’s hardware manual for details.

• The USB control can be used with Windows 95 OSR 2.1 or higher. It may not be possible to use the remote control, depending on the computer’s configurations and mouse drivers.

• The USB control can only be used for the functions listed above. You cannot do things like press two buttons at once (for instance, pressing two buttons at the same time to move the mouse pointer diagonally).

• This function is not available while the lamp is warming up (the POWER indicator flashes green), while adjusting the volume and display, correcting for trapezoidal distortion, zooming in on the screen, using the BLANK function, or displaying the menu screen.

24

01CPX385/EN最終  02.11.7 4:15 PM  ページ 25

THE LAMP

HIGH VOLTAGE

HIGH TEMPERATURE

HIGH PRESSURE

Before replacing the lamp, check the serial number of the replacement lamp bulb (sold separately:

DT00431), then contact your local dealer. Before replacing the lamp, turn off the power, and unplug the power cord, then wait at least 45 minutes, in order to ensure that the lamp is properly cooled.

Removing the lamp bulb while it is still hot could cause burns, or cause the lamp bulb to burst.

WARNING

The LCD projector uses a glass lamp bulb. It is a mercury lamp with high internal pressure. High-pressure mercury lamps can break with a loud bang, or burn out, if jolted or scratched, or through wear over time. Each lamp has a different lifetime, and some may burst or burn out soon after you start using them. In addition, when the bulb bursts, it is possible for shards of glass to fly into the lamp housing, and for gas containing mercury to escape from the projector’s vent holes.

• Handle with care: jolting or scratching could cause the lamp bulb to burst during use.

lamp for long periods of time, or past the replacement date, could cause it to burst. Do not use old (used) lamps; this is a cause of breakage.

• If the lamp breaks soon after the first time it is used, it is possible that there are electrical problems elsewhere besides the lamp. If this happens, contact your local dealer.

• If the lamp should break (it will make a loud bang when it does), ventilate the room well, and make sure not to breathe the gas that comes out of the projector vents, or get it in your eyes or mouth.

• If the lamp should break (it will make a loud bang when it does), unplug the power cord from the outlet, and make sure to request a replacement lamp from your local dealer. Note that shards of glass could damage the projector’s internals, or cause injury during handling, so please do not try to clean the projector or replace the lamp yourself.

• Obey local ordinances when disposing of used lamps. In most cases, it is possible to dispose of used bulbs in the same manner as used glass bottles, but in some cases, bulbs are sorted separately.

• Do not use the projector with the lamp cover removed.

25

01CPX385/EN最終  02.11.7 4:15 PM  ページ 26

THE LAMP (continued)

Replacing the lamp

All projector lamps will wear out eventually. If used for long periods of time, the image could become darkened, and the color contrast could be impacted as well. We recommend that you replace your lamps early. If the LAMP indicator turns red, or a message prompts you to replace the lamp when you power up

1 witch the projector OFF, remove the power cord from the power outlet, and wait at least 45 minutes for the unit to cool.

2

Prepare a new lamp.

3

Check that the projector has cooled sufficiently, and gently turn it upside down.

4

Loosen the two screws as shown in the diagram, and remove the lamp cover.

6

Install the new lamp and tighten the three screws firmly. Also steadily push the opposite side of the screwed lamp into the unit.

7

Replace the lamp cover in position and tighten the two screws firmly.

5

Loosen the three screws, and gently remove the lamp while holding the grips. Touching the inside of the lamp case may result in uneven coloring.

8

Gently turn the projector rightside up.

ATTENTION • Make sure that the screws are screwed in firmly. Loose screws could result in damage or injury.

• Do not use with lamp cover removed.

• Do not reset the lamp timer without replacing the lamp. Reset the lamp timer always when replacing the lamp. The message functions will not operate properly if the lamp timer is not reset correctly.

• When the lamp has been replaced after the message of "CHANGE THE LAMP ...THE POWER

WILL TURN OFF AFTER 0 hr." is displayed, or the LAMP indicator is red, complete the following operation within 10 minutes of switching power ON.

26

NOTE • The LAMP indicator is also red when the lamp unit reaches high temperature.

Before replacing the lamp, switch power OFF, wait approximately 20 minutes, and switch power

ON again. If the LAMP indicator is still red, replace the lamp.

01CPX385/EN最終  02.11.7 4:15 PM  ページ 27

THE AIR FILTER

Caring for the air filter

The air filter should be cleaned about every 100 hours. If the LAMP indicator and

TEMP indicator blink red simultaneously, or a message prompts you to clean the air filter when you turn on the unit, the filter needs to be cleaned. (See "Related

1

Turn off the projector, and unplug the power cord

2

Apply a vacuum cleaner to the top of the air filter cover to clean the air filter

Filter Cover

3

Turn on the projector, and use the menu to reset the filter timer

• To reset the air filter timer, from the OPTION menu, select FILTER TIME.

27

01CPX385/EN最終  02.11.7 4:15 PM  ページ 28

THE AIR FILTER (continued)

Replacing the air filter

If the soiling will not come off the air filter, or it becomes damaged, then it needs to be replaced. Please contact your local dealer, after confirming the model of your

1

Turn off the projector, and unplug the power cord. Prepare a new air filter (one specified for your projector)

2

Remove the air filter cover and air filter

3

Insert the new filter, and replace the filter cover

4

Turn on the projector power, and using the menu, reset the filter timer

• To reset the lamp timer, from the OPTION menu, select FILTER TIME.

ATTENTION • Make sure to turn off the power and unplug the power cord before caring for the unit. Please carefully read "Safety Instructions", in order to care for your projector correctly.

• Do not use with air filter cover removed.

• If the air filter becomes clogged by dust or the like, internal temperature rises and could cause malfunction. The power is automatically turned off in order to prevent the unit from overheating internally.

28

01CPX385/EN最終  02.11.7 4:15 PM  ページ 29

THE HANDLE

Fixing the Handle

Fix the enclosed handle if you need.

1

Raise up the handle hook, and pass one end of the handle through the hole of handle hook.

2

Buckle the end of the handle, as the right drawing.

3

Fix the other end of the handle to the other handle hook in the same way.

CAUTION • Make sure the handle is fixed before carrying the projector with the handle. If the projector should be dropped from the handle should be off, it could result in an injury, and continued use could result in fire or electrical shock. Do not flourish the projector with the handle.

OTHER CARE

Caring for the inside of the projector :

In order to ensure the safe use of your projector, please have it cleaned and inspected by your local dealer about once every 2 years. Never try to care for the inside of the unit yourself. Doing so is dangerous.

Caring for the lens :

Lightly wipe the lens with a commercially available lens-cleaning wipe. Do not touch the lens directly with your hand.

Caring for the cabinet and remote control transmitter :

Wipe lightly with gauze or a soft cloth. If soiling is severe, dip a soft cloth in water or a neutral cleanser diluted in water, and wipe lightly after wringing well. Then, wipe lightly with a soft, dry cloth.

ATTENTION • Make sure to turn off the power and unplug the power cord before caring for the unit. Please carefully read "Safety Instructions" in this manual, in order to care for your projector correctly.

• Do not use cleaners or chemicals other than those listed above, including benzene and paint thinner.

• Do not use aerosols or sprays.

• Do not polish or wipe with hard objects.

29