Phoenix Notebook Computer User Manual

Add to My manuals
115 Pages

advertisement

Phoenix Notebook Computer User Manual | Manualzz

User's Guide

Notebook

Computer

Preface

 Copyright 2003

All Rights Reserved.

Manual edition, 2003

The information in this document is subject to change without prior notice in order to improve reliability, design and function and does not represent a commitment on the part of the manufacturer.

In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use the product or documentation, even if advised of the possibility of such damages.

This document contains proprietary information protected by copyright. All rights are reserved. No part of this manual may be reproduced by any mechanical, electronic, or other means in any form without prior written permission of the manufacturer.

Trademarks

Phoenix is a trademark of Phoenix BIOS Corporation. AutoCAD and Autoshade are trademarks of Autodesk, Inc. IBM, OS/2, and VGA are trademarks of International

Business Machines Corp. Lotus, 1-2-3, and Symphony are trademarks of Lotus

Development Corp. Windows, Word, MS-DOS, and Microsoft are trademarks of

Microsoft Corp. VESA is a trademark of Video Electronics Standards Association.

Other product names mentioned herein are used for identification purposes only and may be trademarks and/or registered trademarks of their respective companies.

Limitation of Liability

While reasonable efforts have been made to ensure the accuracy of this manual, the manufacturer and distributor assume no liability resulting from errors or omissions in this manual, or from the use of the information contained herein.

Notices

Federal Communications Commission Radio Frequency Interference

Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio TV technician for help.

Notice:

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. ii

Shielded interface cables and a non-shielded AC power cord must be used in order to comply with emission limits.

This equipment is to be used with power supply:

I/P: 100-240 Vac, 50-60Hz, 1.5A

O/P: 19Vdc, 4.74A

There is no internal power supply.

Canadian DOC Notice For Class B Computing Devices

This Class B digital apparatus meets all requirements of the Canadian Interference -

Causing Equipment Regulations.

Cet appareil numerique de la classe B repecte toutes les exigences du Règlement sur le matèriel brouilleur du Canada.

Safety Precautions

This section is designed to assist you in identifying potentially unsafe conditions while working with this product. Required safety features have been installed in the computer to protect you from injury. However, you should use good judgment to identify potential safety hazards:

1.

2.

3.

Please read these safety instructions carefully.

Please keep this User's Manual for later reference.

4.

5.

6.

Please disconnect this equipment from AC outlet before cleaning. Don't use liquid or sprayed detergent for cleaning. Use moisture sheet or cloth for cleaning.

For pluggable equipment, that the socket-outlet shall be installed near the equipment and shall be easily accessible.

Please keep this equipment from humidity.

7.

Lay this equipment on a reliable surface when installed. A drop or fall could cause injury.

Make sure to use the right voltage for the power source when connecting the iii

8.

9.

10.

11.

12.

13.

14.

15.

16.

17. equipment to the power outlet.

Place the power cord in such a way that people can not step on it. Do not place anything on top of the power cord.

All cautions and warnings on the equipment should be noted.

If the equipment is not use for a long time, disconnect the equipment from the main power outlet to avoid being damaged by transient overvoltage.

Never pour any liquid into the opening, this could cause fire or electrical shock.

Never open the equipment. For safety reason, the equipment should only be opened by a qualified service personnel.

If on the following situations arises, get the equipment checked by a service personnel: a. The Power cord or plug is damaged. b. Liquid has penetrated into the equipment. c. The equipment has been exposed to moisture. d. The equipment has not worked well or you cannot get it work according to the user's manual. e. The equipment has dropped and damaged. f. If the equipment has obvious sign of breakage.

Do not leave this equipment in an environment unconditioned, storage temperature above 60 ° C (140 ° f), it may damage the equipment.

The unit can be operated at an ambient temperature of max. 35 ° C.

The sound pressure level at the operators position according to IEC 704-1: 1982 is equal or less than 70 dB(A).

Power Cord Requirements

The power cord set used with the AC adaptor must meet the requirements of the country where you use the AC adaptor, whether it is 100-120 or 200-240 Vac. The following information explains the requirements for power cord set selection. iv

18.

19.

A.

B.

• The cord set must be approved for the country in which it is used.

• The appliance coupler must have a configuration for mating with a

CEE22/EN6032/IEC 320 appliance inlet.

For U.S. and Canada:

• The cord set must be UL Listed and CSA Certified.

• The minimum specifications for the flexible cord are No. 18 AWG.

For Japan:

• All components of the cord set must bear a “ T ” mark and registration number in accordance with the Japanese Dentori Law.

• The minimum specifications for the flexible cord are .75m

㎡ conductors.

C. For Other Countries:

• The cord set fittings must bear the certification mark of the agency responsible for evaluation in a specific country.

• The flexible cord must be of a HAR (harmonized) type H05VV-F.

• The cord set must have a current capacity of a least 2.5 Amperes and voltage rating of 125 or 250 Vac.

When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons. These precautions includes the following:

1. Do not use this product near water, for example, near a bathtub, washbowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool.

2. Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning.

3. Do not use the telephone to report a gas leak in the vicinity of the leak.

4. Use only the power cord indicated in this manual.

Do not use the AC adapter near open water or other liquids. Never spill liquid into v

20.

21. the AC adapter.

Laser Warning: Laser Class I Product Caution - Invisible laser radiation when open avoid exposure to beam.

Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer's instructions. Never remove the battery pack while the power is on as this may result in data loss when the system loses power.

Wichtige Sicherheitshinweise

1.

2.

3.

4.

5.

6.

7.

8.

9.

10.

11.

Bitte lesen Sie diese Hinweis sorgfältig durch.

Heben Sie dirse Anleitung für den späteren Gebrauch auf.

Vor jedem Reinigen ist das Gerät vom Stromnetz zu trennen. Versenden Sie Keine

Flüssig- oder Aerosolreiniger. Am besten eignet sich ein angefeuchtetes Tuch zur

Reinigung.

Die Netzanschlu β steckdose soll nahe dem Gerät angebracht und leicht zugänglich sein.

Das Gerät ist vor Feuchtigkeit zu schützen.

Bei der Aufstellung des Gerätes ist auf sicheren Stand zu achten. Ein Kippen oder

Fallen könnte Beschädigungen hervorrufen.

Beachten Sie beim Anschluß an das Stromnet die Anschlußwerte.

Verlegen Sie die Netzanschlußleitung so, daß niemand darüber fallen kann. Es sollte auch nichts auf der Leitun abgestellt werden.

Alle Hinweise und Warnungen, die sich am Gerät befinden, sind zu beachten.

Wird das Gerät üeinen längeren Zeitraum nicht benutzt, sollten Sie es vom

Stromnetz trennen. Somit wird im Falle einer Überspannung eine Beschädigung vermieden.

Durch die Lüftungsöffnungen dürfen niemals Gegenstände oder Flüssigkeien in das vi

12.

13.

14.

15.

16.

17.

Gerät gelangen. Dies könne einen Brand bzw. Elektrischen Schlag auslösen.

Öffnen Sie niemals das Gerät. Das Gerät darf aus Gründen der elektrischen

Sicherheit nur von authorisiertem Servicepersonal geöffnet werden.

Wenn folgende Situationen auftreten ist das Gerät vom Stromnetz zu trennen und von einer qualifizierten Servicestelle zu Überprüfung.: a. Netzlabel oder Netzstecker sind beschädigt. b. Flüssigkeit ist in das Gerät eingedrungen. c. Das Gerät war Feuchtigkeit ausgesetzt. d. Wenn das Gerät nicht der Bedienungsanleitung entsprechend funktioniert oder Sie mit Hilfe dieser Anleitung keine Verbesserung erzielen. e. Das Gerät ist gefallen und/oder das Gehäuse ist beschädigt. f. Wenn das Gerät deutliche Anzeichen eines Defektes aufweist.

VORSICHT : Explosiongsgetahr bei unsachgemäßen Austausch der Batterie.

Ersatz nur durch denselben oder einem vom Hersteller empfohlenem ähnlichen Typ.

Entsorgung gebrauchter Batterien nach Angaben des Herstellers.

Dieses Schaltnetzteil kann bis zu einer Außentemperatur von maximal 35ºC.

Die Ausgangswerte dürfen nicht die auf dem Label angegebenen Werte

überschreiten.

Anforderungen an das Stromkabel

Das Kabel-Set, das an das Netzteil angeschlossen wird, muss den Anforderungen des Landes, in dem Sie das Netzteil einsetzen, genügen, je nachdem, ob die

Netzspannung 100-120 oder 200-240V Wechselspannung beträgt.

• Das Kabel-Set muss für das Land, in dem es eingesetzt wird, zugelassen sein.

• Der Gerätestecker des Kabels muss in eine CEE22/ EN603/ IEC 320

Buchse passen.

A. Für die USA und Kanada: vii

viii

18.

19.

20.

B.

• Das Kabel-Set muss UL-gelistet und CSA zertifiziert sein.

• Die Minimalanforderungen für das Kabel entsprechen No. 18 AWG.

Für Japan:

• Alle Teile des Kabel-Sets müssen entsprechend dem japanischen

Dentori Law mit einem “T”-Symbol markiert sein

• Die Minimalanforderungen für das Kabel sind .75m ㎡ Leiter.

C. Für andere Länder:

• Die Zubehörteile des Kabel-Sets müssen das Prüfsiegel derjenigen

Stelle, die in dem jeweiligen Land für die Sicherheitsprüfung zuständig ist, tragen.

• Das Kabel muss vom HAR (harmonisierten) Typ H05VV-F sein.

• Das Kabel-Set muss eine Stromkapazität von mindestens 2,5 Ampere haben und Spannungen von 125 oder 250 V Wechselstrom gestatten.

Bei der Benutzung Ihres Telefongerätes sollten Sie immer die grundlegenden

Sicherheitsmaßnahmen beachten, um das Risiko von Feuer, Stromschlägen und

Verletzungen zu minimieren. Zu beachten sind u.a. folgende Punkte:

1. Benutzen Sie das Gerät nicht in der Nähe von Wasser, wie zum Beispiel

Badewanne, Waschbecken, Spülbecken, Waschbottich, in feuchten

Kellerräumen oder in der Nähe von Schwimmbecken.

2. Benutzen Sie kein Telefon (ausgenommen schnurlose Modelle) während eines Gewitters. Es besteht das geringe Restrisiko eines Blitzschlages.

3. Benutzen Sie das Telefon nicht um ein Gasleck zu melden, falls es sich in der Nähe des Lecks befindet.

4. Benutzen Sie nur solch ein Stromkabel, wie in dieser Anleitung beschrieben.

Benutzen Sie das Netzteil nicht in unmittelbarer Nähe zu Wasser oder anderen

Flüssigkeiten. Gießen Sie nie Flüssigkeiten über das Netzteil.

Achtung Laser: Laser Produkt der Klasse I. Achtung - Unsichtbarer Laserstrahl,

vermeiden Sie Kontakt mit dem Strahl bei offenem Gehäuse.

21. Es besteht Explosionsgefahr, wenn der Akku nicht ordnungsgemäß ersetzt wird.

Ersetzen Sie den Akku nur durch einen Akku gleichen oder äquivalenten Typs, der vom Hersteller empfohlen wird. Entsorgen Sie Akkus entsprechend den

Anweisungen des Herstellers. Entfernen Sie den Akku auf keinen Fall bei eingeschaltetem Notebook, da hierdurch Daten verloren gehen könnten.

Personal Inventory

This Notebook computer system is designed for years of productive and pleasurable computing. Use this section to keep notes about details of your purchase. Update this section when you add new options.

Date of Purchase:

Dealer’s Name:

Phone:

Address:

E-Mail Address:

WWW Site:

Serial Number:

CPU Type:

Hard Disk Capacity:

Memory Capacity:

Optional Equipment: ix

Introduction

1

WARNING:

There are more and more people spending large amounts of time in front of computer monitors now that scientists from many fields including anatomy, psychology, and occupational safety are involved in the study of ergonomically sound work environments.

A few tips to help you work effectively without a lot of physical discomfort:

Purchase a chair with armrests and good back support. Don't slouch when sitting; keep your back straight.

Try to place the LCD panel or external monitor so that there is little glare from the sun on the monitor.

Walk around the room every hour.

Every half hour look away from the computer screen for a few minutes.

Place everything that you need to work within easy reach.

Welcome to the Notebook PC

Congratulations on your purchase of the Notebook PC. Your Notebook features the latest advances in portable computing technology. The Notebook’s modular design provides maximum expandability without compromising portability. The high-performance CPU and enhanced IDE hard drive provides you with extra processing power for handling complex graphics and running large programs.

One PCMCIA slot gives you the ability to use standard PCMCIA cards, such as a LAN adapter or memory cards.

2

Getting to Know Your Computer

Opening the LCD Panel

At the front of the Notebook you will find two external speaker on both sides of the display panel that locks the display in closed position when the Notebook is not in use.

1. Pull up the two external speaker at both sides to make it adjacent to the LCD panel.

2.

3.

4.

Raise the LCD panel.

At any time you can tilt the display toward or away from you to a comfortable viewing position.

To close the LCD panel, raise down the panel then pull down the two external speaker.

3

4

To avoid damage to the display panel:

1. Try not to slam the display upon closing it.

2. Try not to place any object on top when it is closed or open.

3. Be sure the system is turned off or in suspend mode before you close the display panel.

With the LCD screen open, you will see several features important for operating your

Notebook computer.

Each of these features is briefly described below:

5

1.

LCD Screen

Your Notebook computer is equipped with a replaceable color Liquid Crystal Display

(LCD) screen that supports up to 1024 x 768 or 1400 x 1050 x 16M LCD resolution utilizing an AGP BUS.

A built-in backlight allows you to comfortably view the screen even when ambient lighting is low.

2.

External Stereo Speaker

These two speakers provide a true stereo sound for your system.

3.

Short-cut Keys

These two short-cut keys are assigned as functions for: Explorer and mail respectively.

1.

2.

Internet Explorer Button

Use this key to open the Internet Explorer.

Outlook Express Button

Use this key to open Microsoft's Outlook to send/receive your mail.

4.

Power/Resume Button

Pressing this button for 1-2 seconds will turn on the system or pressing this button when the computer is in Suspend mode will resume normal operation. Pressing this button for 4-6 seconds will also turn off the system.

6

5.

Keyboard

Your computer has an 88-key enhanced keyboard that provides all the functions of a standard 101/102 key keyboard.

6.

TouchPad

The TouchPad is hardware-compatible with the IBM PS/2 mouse and softwarecompatible with the Microsoft mouse.

7.

TouchPad Buttons

The buttons below the TouchPad correspond to the left and right buttons on a standard mouse. The PS/2 compatible mouse will work with the Notebook PC’s TouchPad simultaneously.

8.

Scroll Button

Use this button to scroll up and down the scrolling bar.

9.

The Built-in Microphone

The built-in microphone is located to the left of the TouchPad.

10.

System Status Indicator Panel

The system status indicator panel keeps you informed of the computer’s operating status. There are also two system status indicators — Power and Charge LED — on the left side of the notebook. (Please refer to "The Left Side" section description)

Indicates the the computer is accessing the PCMCIA drive.

7

The Front

Indicates that the computer is accessing the DVD-ROM drive.

Indicates that the computer is accessing the hard disk drive.

Indicates that the keyboard is in Num Lock mode.

Indicates when the keyboard is in Caps Lock mode. In this mode, the keyboard produces uppercase text when you press a key. When you press the Caps Lock key again, the indicator goes off and the keyboard produces lowercase text.

Indicates when the keyboard is in Scroll Lock mode. Some applications will move information across the screen differently when

Scroll Lock is on.

8

This application does not apply when the system is power on.

The function of this application is the same as when you are using the Windows based Media Player in playing a music CD.

1.

The Play/Pause Button

Press the Play button to play a selected track. Press the Pause button to freeze the music when necessary. Pressing the button again resumes playing the track from where it was frozen.

2.

The Stop/Eject Button

Press this button to stop a track. If you then press the Play button or the button of the stopped track, the track restarts from its very beginning.

Press this button to open the disc tray. The button then changes to Close, waiting for you to change the disc and close the tray.

3.

The Previous Track Button

Press this button to start the previous track.

4.

The Next Track Button

Press this button to start the next track.

5.

The Volume Buttons

Press the left button to decrease the volume or the right button to increase the volume of the played track.

6.

Audio DJ Power Button

Slide this Power button to power on the audio DJ.

You will not be able to use this button to turn off the

Windows based CD Player application when the notebook computer is in operation.

9

The Left Side

10

1.

Ventilation Opening

Please don’t block this opening during operation of the system.

2.

The LAN Port

This jack provides a standard RJ-45 connection for integration with an existing network or a high-speed (ADSL or cable) connection via a network cable.

When using a LAN, please use an EMI Shielding Cable to minimize an inteference when transmitting.

3.

1394 USB

A fast external bus standard that supports data transfer rates of up to 400 Mbps (400 million bits per second). Can be used to connect up 63 external devices, also supports isochronous data -- delivering data at a guaranteed rate.

This makes it ideal for devices that need to transfer high levels of data in real-time, such as video devices. Also supports both Plug-and-Play and hot plugging, and also provides power to peripheral devices.

4.

PCMCIA Socket Cover

Open this cover to access the PCMCIA socket. The computer’s PCMCIA socket lets you extend the capabilities of your computer by inserting PC cards.

5.

PCMCIA Socket Button

The computer has one PCMCIA type II socket

LEDIndicator

11

1.

Battery Charge/Suspend

This indicator will lit when the battery is in charging status. It also indicates when the system enter suspend mode.

2.

Power On

This indicator will lit when the notebook is powered on.

The Right Side

12

1.

The DVD-ROM or DVD Combo

Your Notebook comes with a swappable 5.25" IDE 8X DVD-ROM or 16X Combo drive.

2.

USB Ports

Your computer includes four Universal Serial Bus (USB) 2.0 port. USB2.0 is the latest development in Plug and Play technology.

It will eventually replace the need for separate connectors for external keyboards, serial ports, and parallel (printer) port.

The Rear

1.

Audio Line Out/SPDIF Jack

You can plug an external speaker, headphone or connect the line out jack to an audio device such as a cassette recorder to record the notebook's audio output.

S/PDIF engine receives the digital format data from DVD-ROM or Combo drive, regroup the date to be synchronous signal and de-multiplexes audio and other digital data.

2.

External Microphone Jack

This mono microphone jack is used to connect an external microphone.

13

14

3.

Infrared Data Port

The Infrared Data Port allows your Notebook to become truly wireless. You can use this port to transfer large amounts of data very quickly to any other machine

(Notebook computers, printers, etc.) which is also equipped with an IrDA-compliant

IR port.

This allows you to print documents without any inconvenient cable hookups.

4.

Parallel Port

This port allows you to easily connect a parallel printer or plotter using this 25-pin bidirectional female port.

5.

External CRT Port

This port allows you to easily connect an external VGA/SVGA display monitor into your Notebook using the 15-pin female connector.

6.

TV Out Port

This 4-pin S-Video port allows you to view the Notebook's Video output on a television monitor.

7.

The Modem Port

This jack is an internal 56K voice/fax/data modem. You will connect your computer to your phone line through this port.

Always disconnect all telephone lines from the wall outlet before servicing or disassembling this equipment. To reduce the risk of fire use only No. 26 AWG or larger telecommunication line cord.

8.

DC IN Connector

Plug the AC adapter into this connector.

9.

Ventilation Opening

Please don’t block this opening during operation of the system.

The Bottom Panel

15

1.

Battery

Your notebook comes equipped with a factory-installed battery pack module. After the battery runs down, the module can be removed and replaced with a charged battery.

2.

Battery Release Latch

Lift up this latch to release the battery from its bay.

3.

Hard Disk Drive

Your computer includes a 2.5-inch IDE hard disk drive (9.5mm in height). The notebook PC's BIOS automatically detects IDE drive types.

4.

DVD-ROM Release Latch

Push this latch to release the DVD-ROM from its bay.

5.

Expansion Compartment

This compartment will serve as an expansion to upgrade your RAM module.

6.

CPU Compartment

This compartment will serve as upgrading your system CPU.

16

Getting Started

2

Connecting to a Power Source

Connecting the AC Adapter

A universal AC adapter is provided to supply your computer with power and also charge the computer’s battery pack.

The adapter’s AC input voltage can range anywhere from 100 to 240 volts, covering the standard voltages available in almost every country.

The power cord for the AC adapter requires a three-hole grounded AC outlet. To connect the computer to an external power source:

1. Plug the AC adapter’s connector into the DC-IN connector on the rear of the computer.

2. Connect the power cord to the AC adapter and then to a wall outlet.

18

The best kind of AC power source to connect your Notebook to is a UPS (Uninterruptible

Power Supply). Lacking this, use a power strip with a built-in surge protector. Do not use inferior extension cords as this may result in damage to your Notebook. The

Notebook comes with its own AC adapter. Do not use a different adapter to power the computer and other electrical devices.

Whenever possible, keep the AC adapter plugged into the Notebook and an electrical outlet to recharge the battery.

Never turn off or reset your Notebook while the hard disk is in use and the HDD status icon is lit; doing so can result in loss or destruction of your data. Always wait at least 5 seconds after turning off your Notebook before turning it back on; turning the power on and off in rapid succession can damage the Notebook’s electrical circuitry.

Turning On Your Notebook Computer

Turn on your Notebook by pressing the power button. Hold the button down for a second or two and release. The Power-On Self Test (POST) runs automatically.

After the POST is completed, the computer reads the operating system from the hard disk drive into computer memory (this is commonly referred to as “booting” a computer). If your OS (Operating System such as Windows ME, Windows 2000…. etc) is installed, it should start automatically.

To turn the Notebook off, save your work and close all open applications, click on Start , then Shut Down and select Shut down the computer and click " Yes " or press the power button for 4-6 seconds.

Operating on Battery Power

Your computer comes with a rechargeable battery pack that lets you operate the computer without an external power source. When the battery pack is fully charged, you can operate the computer for approximately 2 hours under the following conditions:

19

The battery pack initially has a full charge.

No peripheral devices are installed.

The disk/DVD-ROM drives run no more than 10% of the time.

Only use batteries that are approved by an authorized dealer. All batteries are not the same and therefore should not be treated as such. Using the wrong battery could cause serious damage to your computer and yourself through toxic emissions.

Inserting and Removing the Battery Pack

The battery pack should already be inserted in your Notebook computer when you unpack it. If not inserted, follow these directions:

1. Turn over the notebook with the front of the unit facing you and place it on a solid, flat surface.

2. Angle the battery into the bay. The front edge of the battery should slide into the grooves in the system case.

20

3.

To remove the battery pack:

1. Turn off the notebook, and disconnect the AC adapter. Close the LCD panel and turn it over and place it on a solid, flat surface.

2.

Gently lower the battery into the bay and push it until it clicks securely in the bay.

Lift the release latch to release the battery from the bay. At this time the battery will now be angled slightly out of the bay.

21

22

3. Hold the battery at the finger grip and lift it out of the compartment.

Charging the Battery Pack

The installed battery pack charges automatically any time the computer is connected to the AC adapter and an external power source.

If this is your first t fully discharge the fully charged. ime to use the battery, be sure to battery and recharged until it is

Using the Noteboo k

Computer

3

23

Adjusting the LCD Screen Display

The LCD screen display can be adjusted by the following key combinations.

KEYS FUNCTIONS

[Fn] + [F7] Decreases the brightness level.

[Fn] + [F8] Increases the brightness level.

[Fn] + [F10] Use this key combination to expand your video screen or reset to its original size.

[Fn] + [F12] This key combination toggles the display between the LCD, CRT, simultaneous LCD/CRT, TV, simultaneous CRT/TV.

LCD Care

L CD screens are delicate devices that need careful handling. Please pay attention to the fo llowing precautions:

When you are not using the computer, keep the LCD screen closed to protect it from dust.

If you need to clean y our LCD screen, use a soft tissue to gently wipe the LCD surface.

D o not put your fingers or sharp objects directly on the surface and never spray cleaner di rectly onto the display.

D o not press on, or store any objects on the cove r when it is closed. Doing so may cause the LCD to break.

External CRT Display

You can hook up an external monitor through the 15-pin CRT connector. Five configurations are available:

LCD only

CRT only

24

Simultaneous display of the LCD scre

TV only en and CRT monitor

Simultaneous display of the TV screen and CRT monitor

You can s witch between these display configu

+ [F12] . F or information on connecting an ext rations by pr essing the key combination [Fn] ernal display , please refer to Chapter Four.

A Tour of the No tebook’s Keyboard

The Notebo ok ’s keyboard uses a standard QWERTY layout with the addition of special function key keyboard su s and an embedded numeric keypad for number intensive data ent pports Windows by incorporating the two Windows sp ry. Your ecific keys. With the two Window s keys you will be able to access and take advantage of many of the timesaving fe atures of Windows software.

The function keys (F1-F12) on the top row of the keyboard, serve different purposes and carry out different task s depending on the application you are running.

The cursor (arrow) keys (which are all located in the lower right corner of your keyboar d) and the [P gUp], [PgDn], [Home] and [End] keys (which are located along the right edge of th e keyboard) allow you to move the active cursor of the computer to various locations on the screen or within the document.

Th e embedded numeric key pad consists of 15 keys that make number intensive input more convenient. Like the [Num Lock] key, these keys are labeled in blue on the key caps.

Numeric assignments are located at the upper right of each key.

When the numeric keypad is engaged, the NumLock icon will appear in the System

Window. The keypad is ac tivated by pressing the [Fn] + [NumLk] key. If an external keyboard is connected, pr essing the NumLock key on either the Notebook or external keyboard will enable/disable NumLock of both keyboards in unison.

To disable the Notebook nu key board activated, meric keypad while keeping the keypad on an external use the [Fn] + [NumLk] hot key on the Notebook keyboard.

25

The Notebook’s Hot Key Controls

KEYS FUNCTION(S)

Power Button Press this button once to power on or enter the suspend/resume mode.

Press this button for more than 4 seconds to power off the system.

Internet Button Open Internet WWW Home short-cut key

Email Button Open Email Reader short-cut key

[Fn] + [F2]

[Fn] + [F3]

[Fn] + [F4]

[Fn] + [F7]

[Fn] + [F8]

[Fn] + [F10]

[Fn] + [F12]

This key combination turns on/off the volume.

Decreases the speaker volume.

Increases the speaker volume.

Decreases the brightness level.

Increases the brightness level.

Use this key combination to expand your video screen or reset to its original size.

This key combination toggles the display between the LCD, CRT, simultaneous LCD/CRT, TV, simultaneous CRT/TV.

The T ouchPad

The touchpad is a rectangular electronic panel located just below your keyboard. You can use the static-sensitive panel of the touchpad and slit it to move the cursor. You can use the buttons below the touchpad as left and right mouse buttons.

26

TouchPad Precautions

The TouchPad is a pressure sensitive device. Please take note of the following precautions.

• Make sure the TouchPad does not come into contact with dirt, liquids or grease.

Do not touch the TouchPad if your fingers are dirty.

Do not rest heavy objects on the TouchPad or the TouchPad buttons.

You can use the TouchPad with Microsoft Windows as well as non-Windows applications.

27

Connecting an External Tracking Devices

The system will only enables you to use one tracking device whether it is an intern al or external tracking device.

Data Storage and Retrieval

Data storage and retrieval are two of the most fundamental tasks you will perform when working with your computer. The Notebook is equipped with a hard disk drive (HDD).

The HDD is removable allowing for easy upgrades.

The DVD-ROM/ Combo

Features of the DVD-ROM/Combo Module

The features of the DVD-ROM/Combo drive are listed below.

The Audio Play feature allows you to play music CDs

Front panel load/unload button

Supports CD-DA, DVD-ROM mode 1 and mode 2, Multi-Session Photo CD™, CD-

I/Video CD (pcs.)

Low power consumption

12.7mm height

Precautio ns for Handling DVD-ROM/Combo Discs

Always hold the disc by the edges, avoid touching the surface.

Use a clean, dry, cloth to remove dust, smudges, or fingerprints. Wipe from the center outward.

Do not write or place objects on the surface of the disc.

28

Store discs in a cool dry place not to damage the disc.

Do not use benzene, thinners, or cleaners with de tergent. Only use DVD-ROM cleaning kits.

Do not bend or drop the discs.

Loading a Disc

To play a CD disc, follow the instructions listed below.

1. Push the DVD-ROM/Combo eject button on the CD drive door. Gently pull the tray all the way out.

2. Carefully lift the D VD-ROM/Combo by the edges and make sure the shiny surface is face down (the si the tray. Push the D de with no writing on it). Carefully insert the DVD-ROM onto

VD-ROM down gently so that it snaps onto the center ring.

3. Push the tray back into the drive.

To remove a disk, do the following:

1. Check the LED display and make sure that the computer is not accessing the DVD-

ROM drive.

2. Push the eject button and pull the tray all the way out.

3. Carefully pick up the CD disk by the edges and – while pressing down on the center ring – remove th e DVD-ROM/Combo from the tray.

D o not insert any foreign objects into the disc tray. If you experience difficulty when ejecting the CD disk tray, stretch a paper clip (or use a pin or a th insert it into the emergency eject hole l in metal rod) and ocated on the right side of the front panel. The CD dis k tray should eject immediately. This procedure can also be used to remove a CD from the drive when the Notebook is powered off.

29

30

1. Push the r elease latch into the direction of the arrow as described in the illust ration.

2. Pull out the DVD-ROM drive from the bay.

PCMCIA Cards and Expansion Sockets

The Noteboo k features one PCMCIA expansion socket design to interface with one

II card.

Type

31

Inserting a PCMCIA Card

The co mputer will emit a medium tone followed by a high tone when a PC c ard is inserted.

When y ou eject a card, the computer will emit a high tone followed by a me dium tone.

You can ins ert and remove a PC card whether the computer is turned On or Off .

Follow these instructions to insert a PCMCIA card:

1.

2.

Hold the PCMCIA card with the arrow side up and the connector side toward socket. the

Align the card connectors with the socket and carefully slide into the so cket until it locks into place. The system will beep once to indicate that it has dete cted the PC card.

To remov e a PC card push the eject button, the button will pop out, push th e button again to eject the PCMCIA.

When inserting a Type II PC card, make sure the connector is inserted in the socket. Before ejec ting a PC card, ensure that it is not being accessed by the S ystem.

For example, if the message “Write protect error wri ting

Drive x” is displayed, the user has to change the wri protect switch setting on the memory card. To cha te nge the switch setting, (a) eject the card, (b) change the switch setting, and (c) re-insert the card.

Alway s disconnect all telephone lines from the wall outlet before servicing or disassembling this equipment. To reduce the risk of fire, use only No. 26 AWG or larger telecommunication line cord.

32

Power Saving Modes

This section contains information on the Notebook’s power system, including the AC

Adapter, the battery system, recharging the battery, and tips for conserving battery power.

The power system is comprised of two parts, the AC Adapter and the battery system. The

AC Adapter converts AC power from a wall ou tlet to the DC power required by the comp uter.

The Battery Power System

A full y charged pack will provide approximately 2 hours of battery life depending on yo ur sy stem conf iguration application it runs.

Before using the computer on battery power for the first time, check the battery status icon on the Windows To olbar to make sure the battery is fully charged.

S ee Battery St at us later in this section for a description and explanation of the Windows

Battery icon. Ch arging the battery takes about 3 hours to charge when the system is in off st ate. If poss i ble , always charge the battery completely.

Removing th e Battery Pack

To remove the b and Removing t attery pack from its compartment, please refer to Chapter Two, Inse he Battery Pack . rting

Preparing the Battery Pack for Use

Before using the battery pack for the first time, the Smart Battery IC within the battery pack should be calibrated in order to get accurate reporting of remaining battery life status.

To calibrate the battery pack follows the instructions below:

1. Insert the battery into the battery compartment and turn on the Notebook. If the battery is completely without power go to the next step.

33

Otherwise, let t he battery run down until the battery low-low warning beeps are heard.

The system will automatically enter Suspend mode.

2. Turn the Notebook off. Connect the AC adapter and let the battery fully recharge.

When the battery charge indicator turns off, the battery is fully charged.

3. Turn On the notebook, let the battery run down until the battery is in low-low state and you hear a warning beeps. The system will automatically enter the Suspend mode . You can now connect the AC adapter.

4. The battery pack is now cal ibrated properly.

In general, using the battery until the low-low battery-warning indicator appears and fully recharges the battery each time (full discharge/charge cycle) will ensure the accurate reporting of the battery gauge status.

Automatic Battery Pack Charging Function

You can automatically charge the battery pack by using the AC Adapter. The charge time is about three hours when the Notebook power is turned off. The following table summarizes the charging modes:

Charge Mode

Fast

Pre-Charge

Charge Time

3 hours with the system off or in Suspend mode. The temperature must be 25 ° C or below room temperature.

A pre-charge is supplied to the Li-Ion battery pack.

Battery Status

Windows 98/ME/2000/XP has an applet in the Control Panel that will display an icon in the Windows taskbar indicating when the Notebook is running on battery power or is attached to the AC adapter.

34

This applet also displays a meter that indicates how much charge is remaining in the battery.

Batte ry Low Warning

When the pack initially reaches the “Battery Low” state approximately 10 ~ 15 minutes of the us able battery life is left.

You w ill hear an audible beep signal every 1.5 seconds alerting you to the “Battery Low ” status . When the battery power reaches the “Battery Low Low” status the beeping soun will acce lerate. d

Your b attery now has 1 ~ 2 minutes of battery ch arge remaining. You must save your data or connect AC power immediately; otherwise, you may lose your data.

Sound Meaning

Continuous beeping every 1.5 seconds

Battery Lo w: remaining.

Indicates that there is 7 to 10 minutes charge

Beeping accelerates Battery Low Low: Indicates that there is 1 to 2 minutes of battery charge remaining. Save your work and turn off the

Notebook, or connect the AC adapter.

When there is only one minute of battery charge remaining, the Notebook will suspend to the HDD and power off. You should connect AC power and resume to save your work.

S mal l Battery for the Real Time Clock

T here is a s mall built-in battery pack that supplies power to the maintain certain system information while the power is off.

system in order to

If the Notebook is left without a power source for long period of time, this battery will be exhausted and system information will be lost.

Danger of explosion if battery is incorrectly replaced.

Replace o nly with the same or equivalent type recommended by the manufacturer. Dispose of used

35

batteries according to the manufacturer's instructions.

Never remove the battery pack while the power is on as this may result in data loss when the system loses power.

Resetting the System

After installing a software application package, you may be prompted to reset the system to load the changed operating environment. To reset the system, or “ reboot ,” press the

[Ctrl] + [Alt] + [Delete] keys simultaneously. This is known as “ warm boot .” This key combination acts as “ software ” reset switch when you encounter hardware or software problems, which lock up the Notebook.

If this key combination does not shut down the Notebook, you can reset the Notebook by using the Notebook’s power button. Should the Notebook lock up fo r some reason, pressing this but ton powers the Notebook off.

A djusting the Br ight ness

To adjust the brightness on the LCD screen, press and hold down the [Fn] key in the lower left hand corner of the keyboard and press the [F7] key to reduce the brightness or

[F8] to increase the brightness.

36

Desktop Operation

4

Audio

ur notebook is capable of providing you with efficient and productive mobile computing, it also has the speed and capacity to service as a desktop system.

This chapter discusses those functions of your notebook that are typical of desktop systems.

The Multimedia Sound System

The Notebook’s built-in audio capabilities allow you to take advantage of a wide range of education and entertainment multimedia software. The Notebook is equipped with two internal stereo speakers, a microphone, and input audio ports for external audio units.

An hea external microphone can be connected to the microphone jack. dphones can be connected to the Notebook’s audio-out jack.

External speakers or

External audio devices can be connected to the Line in jack. All audio features are software controlled. The Notebook’s multimedia sound system includes the following features:

Supports Windows Sound System compatibility

Full Duplex operation

Dynamic filtering reduces noise and distortion rate

16-bit digitized audio playback

A built-in microphone for convenient recording

Two built-in stereo speakers

Digitized audio recording through the Notebook’s built-in microphone or any external source

38

Audio Volume Control

The Notebook is equipped with hot-key volume controls: Pressing the [Fn] + [F3] hot-key combination decreases the audio output volume, press the [Fn] + [F4] hot-key combination increases the audio output volume.

Audio Software

Your notebook comes equipped with an integrated sound system capable of providing you with quality audio sound through th e built-in speakers or through external speakers connected via the system ports.

Sound Recording

Your system allows you to record sounds and store them as files using the microphone via the microphone jack on the rear of the notebook computer. Check the Windows Help and

Support Center in Windows for information on using the various elements in sound recording.

For a high-quality sound, click on the "Volume Control" at the lower right end of your s creen. From the Volume

Control windows, click on the "Advanced" tab, click and select the "Microphone Boost" item.

Playing Sound Files

Your notebook can play audio files stored in MIDI, WAVE or MP3 file format. Check the Help and Support Center in Windows for information on the functions of the Medi a

Pla yer.

39

External Speakers and Microphone

The sound system is capable in providing high-quality sound to external speakers and receiving and processing sounds from an external microphone or external sound source.

Connecting Peripheral Devices

To expand your computing capabilities, you can add a variety of external devices to your computer. You may, for example, want to add a mouse, modem, or a printer.

The computer is equipped wit h several interface ports, including an enhanced parallel

(printer) port, a serial port, and USB ports. These are provided as a means of connecting peripheral devices to th e computer.

Connect peripheral devices to the computer's interface ports as shown below:

40

41

42

Running BIOS

Setup

5

Introduction

The BIOS (Basic Input and Output System) Setup program is a menu driven utility that enables you to make changes to the system configuration and tailor your system to reflect installed hardware or alter system performance. When the Notebook is turned ba system is configured with the values stored in CMOS. With easy-to-use menus ck on, the

, you can configure such items as:

• Hard drives and peripherals

• Boot up Drive Sequence

• Password protection

• Power Management Features

The settings made in the BIOS Setup program intimately affect how the Notebook performs.

Navigating through BIOS Setup

The Setup program has been designed to make it as easy to use as possible. If you accidentally make a setting and don’t know which one to switch back to, the Setup program has a hot key that allows you to return to the previo us value.

Accessing the BIOS Setup Program

To access the BIOS Setup program, press the F2 key after the Notebook has run through its

POST.

Item Specific Help

On the right side of the Setup screen is an area labeled Item Specific Help. This area will list navigation key shortcuts and information that is specific for the item that you are currently editing.

44

The Menu Bar

The top of the screen has a menu bar with the following selections:

• Main - Use this menu to make changes to the basic system configuration.

• Advanced - Use this menu to enable and make changes to the advanced features available on your system.

• Security - Use this menu to set a password. The password allows boot up and controls access to the BIOS setup menu.

• Boot - Use this menu to c the Operating System onfigure the default system device used to locate and load

and for booting up the Notebook.

• Exit - Use this menu to exit th e current menu or specify how to exit the Setup program.

To access the menu bar items, press the right or left arrow key on the keyboard until the desired item is highlighted.

The Legend Bar

At the bottom of the Setup screen you will notice a legend bar. The keys in the legend bar allow you to navigate through the various setup menus.

The following table lists the keys found in the legend bar with their corresponding alternates and functions.

Legend Key Alternate Key

F1 Alt + H

Esc

Alt + X

Function

Displays the General Help window. It can be enabled from anywhere in the BIOS.

Jumps to the Exit menu or returns to the Main menu from a submenu.

Selects the menu item to the left.

Selects the menu item to the right.

45

↑ or ↓

Tab

Shift + Tab

Minu e

(

-

)

Keypad arrow keys

Enter

F5

Plus y F6, Space

Home

End

F9

PgUp

PgDn

Moves the cursor up and down between fields.

Moves the cursor to the next position available in the field.

Moves the cursor to previous position available in the field.

Scrolls backward through the values for the highlighted fie ld.

Scrolls forward through the values for the highlighted field.

Moves the cu rsor to the field at the top of the window.

Moves the cursor to the field at the bottom of the window.

Sets the parameters for values. the current menu to their de fault

F10

Enter Will select a sub menu or show a range of options for a field.

Launching Submenus

Note that a right pointer symbol

appears to the left of certain fields. This pointer indicates that a submenu can be launched from this field. A submenu contains additional options for a field parameter. To call up a submenu, simply move the cursor to highlight the field and press the [ Ente r ] key. Use the [ Esc ] key to return to the Main menu.

Genera l Help

In ad dition to the Item Specific Help window, the BIOS Setup program also provides a

General Help screen can be calle d up from an y menu by simply pressing [ F1 ] or the [ Alt ] +

[ H ] combination.

46

Use the [ PgUp ] and [ PgDn ] ke ys or the up and down arrow keys ( ↑↓ ) to scroll through the e ntire he la st pa lp docu ge. To exi ment. Press t t the h he elp windo

Home key to display the first page, press End w, press the [ Enter ] or the [ Esc ] key.

to go to the

Save Changes and Exit the Setup Program

Re fer to the Exit me nu section of exiting th e setup program. this chapter for detailed information on saving change s and

The Main Menu

When the Setup program is access ed, the following screen appears:

47

System Time

Sets your system to the time that you specify. The format is hour, minute, second.

Use the [Tab] or [Shift] + [Tab] keys to move between the hou r, minute, and second fields.

System Date

Sets your system to the date that you specify (usually the current date). The format is month, day, year. Use the [Tab] or [Shift] + [Tab] keys to move between the mo nth, day, and year fields.

`

Primary Master

This fiel d is used to configure the IDE Hard Disk installed in the system. To configure a hard disk d rive, move the cursor to highlight the Primary Master field:

`

Prim ary Master [IC25N040ATCS04-0- (PM)]

Pressing th e [Enter] key at this point will reveal the Primary Master submenu:

48

Before attempting to configure a hard disk drive, make sure you have the configuration information supplied by the manufacturer of your hard drive. Incorrect settings can result in your system not recognizing the installed hard disk.

Type

The following options are available for this field:

Auto (default value), None

Select Auto to automatically configure an IDE type drive. This option only works with standard IDE drives. If your drive is an IDE type, it will be automatically

49

50 recognized and properly configured.

If automatic detection is successful, the correct values will be filled in for the remaining fields on this submenu. If no drive is installed or if you are rem oving a drive and not replacing it, select None .

DVD-ROM if a DVD-ROM is installed as the IDE Adapter 0 Master.

To configure a drive that is not an IDE type drive, if it is User . Manually enter the number of cylinders, heads and sectors per track for your drive. Refer to your drive’s documentation or look on the drive if you need to obtain this information.

ATAPI Removable if the drive is an ATAPI type drive that supports high-capacity storage diskettes. This option would be used in the event that you have swappe d the

DVD-ROM for an ATAPI type removable drive.

Total Sectors

This field configures the drive’s number of sectors per track. If the s ystem has successfully detected the drive automatically, there is no need to adjust this field. In order to make changes to this field, the Type field must be set to User.

Maximum Capacity

Th is field gives the maximum formatted capacity of the hard disk drive. This is a dis pl ay only field.

M ul ti-Sector Transfers

This option automatically sets the number of sectors per block to the highest numb suppo er rted by the drive. This field can also be configured manually. Note that when this field is automatically configured, the set value may not always be the fastest value for the drive.

Ref t h your hard drive to determine the optimal value and set it manually. In order to make changes to this field, the Type field must be set to User. Configuration options are:

Disabled, 2 Sectors, 4 S value) ectors, 8 Sectors, 16 Sectors (default

LBA Mode Control

When enabled, this option uses 28-bit addressing of he hard drive without regard for cylinders, heads, and sectors.

Note that Logical Block Access may decrease the access speed of the hard disk.

In order to make changes to this field, the Type field must be set to User.

Configuration options are:

Disabled, Enabled (default value)

32 Bit I/O

When enabled, this option speeds up communication between the CPU and the IDE controller. Th is option supports PCI local bus only. ISA bus is not supported. Set the Type field to Auto to provide the optimum transfer mode. Configuration options are:

Disabled, Enabled (default value)

Transfer Mode

When enabled, this option speeds up communication between the system and the

IDE controller by using enhanced I/O transfer modes (PIO) Modes.

Set the Type field to Auto to provide the optimum transfer mode. Configurations are:

Standard, Fast PIO 1, Fast PIO 2, Fast PIO 3, Fast PIO 4, FPIO 3

/ DMA 1, FPIO 4 / DMA 2

Ultra DMA Mode

When enabled, this option speeds up data transfer to and from the drive. In order to make changes to this field, the Type field must be set to User .

51

Set the T pe field to Auto to provide the optimum transfer mode. Configurations a re:

Disabl ed, Mode 0, Mode 1, Mode 2 (default value), Mode 3,

Mode 4

After using the legend ke ys to make changes to this submenu, press the [Esc] key to exit back to the Main menu.

`

Second ary Master

The value in this field indicates the type of your Notebook’s DVD-ROM drive. The arrowhead icon configure a DV

indicates that this

O

field contains a submenu. The submenu is used to

D-R M installed in the system.

To configur press the [E e a DVD-R nter] key.

OM, move the cursor to highlight the Secondary Master field, and

The Secondary Master submenu screen will appear. When the Type field is set to “Auto”, only the 32 Bit I/O and Ultra DMA Mode fields are available. When set to “Use r” the fields and options on this submenu are the same as the IDE Adapter 0

Master sub menu described above.

After using the legend keys to make your selections to this submenu, press the [Esc] key to exit back to the n

52

Summary Screen

This field display the system configuration when you boot up the system.

Disabled (default value), Enabled

System Memory

This field display the amount of conventional memory detected by the system during bootup. You do not need to make changes to this field. This is a display only field.

Extended Memory

This field displays the amount of extended memory detected by the system during

53

boot-up. You do not need to make changes to this field. This is a display onl y field.

The Advanced Menu

Selecting Advanced from the menu bar displays the advanced menu:

54

`

I/O Device Configuration

This menu allows you to configure the notebook's serial and parallel ports diskette controller as well as th e peripherals connected to your system. Each field on this submenu is covere d below.

Parallel Port

This field allows you to configure the Notebook’s parallel port.

The following options are available:

Disabled, Enabled (default value)

Changing the default a ddress and IRQ settings for COM1 and the LPT Port can cause conflicts with other sy stem devices or installed peripherals.

55

IrDA/FIR

This field allows you to enable or disable the Notebook's Fast Infrared (FIR) communication module. The following configuration options are available:

Disabled, Enabled (default value)

Base I/O Address

When the Parallel Port is set to Enabled, the "Base I/O Address" field becomes available and you can set the parallel port's I/O address. Available configuratio ns are:

3F8, 2F8 (default value), 3E8, 2E8

Interrupt

Use this option to choose the Interrupt for the Sound chip. Available configurations are:

IRQ 3 (default value), IRQ 4

Mode

This field allows you to configure the notebook's Fast Infrared (FIR) co mmunication module. Available configurations are:

IrDA, FIR (default value)

The Security M enu

The Notebook s advan ced system of security allows yo u to set a password to prevent unauthorize d access to system resources, data, and the BIOS Setup Program.

56

Supervisor Password Is:

This field will show Set when you have set a Supervisor Password as described below. If you have not set the Supervisor Password, the field will show is a display only field.

Clear . This

User Password Is:

This field will show Set when you have set a User Password as described below. If you have not set the User Password, the field will show Clear . This is a display only field.

57

Set Supervisor Password

This field allows you to set the Supervisor password. To set the password, highlight this field and press the [Enter] key. The following

Supervisor dialog box appears:

Set Supervisor Password

Enter New Password

Confirm New

Password

[ ]

[ ]

Type the password and press the [Enter] key. You can type up to seven alphanumeric characters. Symbols and other keys are ignored. To confirm the password, type the password again and press the [Enter] key. The Supervisor password is now set. This password allows full access to the BIOS Setup m enus.

To clear a password, highlight this field and press the [Enter] key. The sa me dialog box as above will appear. Press the [Enter] key twice. The password is now cleared.

Set User Password

This field allows you to set the User password. To set the User password, follow the same instructions for setting the Supervisor password. The User pass restricted access to the Setup menus. word allows

This password also requires that the Supervisor password be set prior to setting the

User password.

Diskette Access

This option requires prior setting of the Supervisor password to function. When set to User , the system will then require either the Supervisor or User password before allowing access to the Floppy Disk Drive (FDD). When set to Supervisor , only the

Supervisor password will allow access to the FDD. The options for this field are:

User (default value), Supervisor

58

Password on Boot

This option requires prior setting of the Supervisor password to function. When enabled, the system will then require either the Supervisor or User password before the system can bootup. The options for this field are:

Disabled ( default value), Enabled

Fixe d Disk Boot Sector

This option r equires prior setting of the Supervisor password to function. When set to Normal , the sy stem will allow normal access to the HDD boot sector. When set to

Write Protect , the BIOS blocks all accesses to the boot sector. The options for this field are:

Normal (default value), Write Protect

Write protecting the HDD boot sector will protect the HDD against boot sector viruses. However, this option may interfere with the normal operation of certain operating systems or a nti-virus programs, which would normally need access to the boot sector area.

The Boot Men u

The Boot m enu allows the user to specify the order in which the Notebook is to check for a device to boot the system. You can also configure the way that the system will boot up. To make chang es, select Boot fro m the menu bar.

The followi ng screen appears:

59

Use the up and down arrows to select the boot device. Then press either the plus key [+] to move the devi ce up the list or the minus key [-] to move the device down the list.

The Exit Menu

Once you have made all of your selections from the various menus in the Setup program, you should save your changes an d exit Setup. Select Exit from the menu bar to display the following menu:

60

Pressing the [Esc] key does not exit this menu. You to exit this menu. must select one of the options from this menu or a menu bar item

Exit Saving Changes

Once you are finished making your selections, choose this option from the Exit menu to ensure the values you selected are saved to Non-Volatile RAM.

Setup Confirmation

Save configuration changes and exit now?

61

[Yes] [No]

Select Yes to save changes and exit the BIOS setup program or press to the Exit menu.

[Esc] to return

The next time you bootup the Notebook, the BIOS will attempt to load t he values you saved in Non-Volatile memory. If these values cause the system boot to fail, reboot and press [F2] to enter the Setup program.

Once in Setup, you can try to change the values that caused the system boot to fail.

If the problem persists, load the default values as described below.

If you attempt to exit the Setup program without sa ving your changes, the program will prompt you with a message asking if you want to save your changes before exi ting.

Exit Discarding Changes

This option should only be used if you do not want to save the changes you have made to the Setup program. If you have made changes to the fields ot system date, system time and password, the system will ask for confirm her than ation when choosing Exit Discarding Changes.

Warning

Configuration has not been saved!

Save before exiting?

[Yes] [No]

Select Yes to save changes and exit the BIOS setup program, select No to exit BIOS without saving your changes, or press [Esc] to return to the Exit menu.

62

Load Setup Defaults

This option allows you to load the default values for each of the parameters on the

Setup menus.

Setup Confirmation

Load default configuration now?

[Yes] [No]

Select Yes to load default values. You can now select Exit Saving Changes or make oth er changes before saving the values to Non-Volatile RAM.

This opti on allows you to discard the selections you’ve made and restore the values you previously saved.

Setup Confirmation

Load previous configuration now?

[Yes] [No]

Select Yes to discard any changes and load the previously saved values.

Save Change s

This option saves your return to other menus

selections without exiting the

and make changes.

Setup program. You can then

Setup Confirmation

Save configuration changes now?

[Yes] [No]

Select Yes to save any changes to Non-Volatile RAM. To exit the BIOS Setup program, open the Exit menu and select one of the exit options.

63

To exit BIOS S etup without saving your changes, select Exit

Discarding Chan ges from the Exit menu and press [Enter].

When prompted by BIOS to save your changes before exiting , select [No] and press [Enter].

64

The Software

Utilities Disks

6

There are two separate procedures on how to install the driver: AutoRun installation and Manual installation .

AutoRun Installation

Follow the step-by-step procedures on the DVD-ROM to execute the “AutoR un” application by selecting the topic of “Driver Installation”.

To re-run the “AutoRun” installation, please refer to the procedures on the “Manual

Installation” for a more detailed explanation.

Intalling the AGP Driver for WinXP

1. Insert the DVDROM Driver into your DVD-ROM drive.

2. Click “Start” and Select “Run”.

3. Type the follo wing: D:\Driver\AGP\SiSSetup.exe (If D is not your DVD-ROM drive, substitu te D with the correct drive letter).

4. Click on “Setup” to begin the Installation Wizard.

5. Follow the Wizard’s on-screen instructions to complete the installation.

6. Restart the system.

Installing VGA Display Drivers for WinXP

This section describes the operation and installation of VGA display software drivers supplied on the Driver Utility DVD-ROM that is shipped with your computer.

1. Insert the DVD-ROM Driver into your DVD-ROM drive.

2. Click “Start” and Select “Run”.

66

3. Type the following: D:\Driver\VGA\ Setup.exe (If D is not your DVD-ROM drive, substitut e D with the correct drive letter).

4. Click on “ Setup” to begin the Installation Wizard.

5. Follo w th e Wizard’s on-screen instructions to complete the installation.

6. Restart the syste m.

Intalling the Audio Driver for WinXP

1.

2.

3.

Insert the DVD-ROM Driver into your DVD-ROM driv e.

Click “Start” and Select “Run”.

Type the following: D:\Driver\Audio\Set substitute D with the correct drive letter) up.exe (If D is not your DVD-ROM drive,

.

4. Click on “Setup” to begin the Installation Wizard.

5.

6.

Follow the Wizard’s on-screen instructions to complete the installation.

Restart the system.

Intal ling the LAN Driver for WinXP

To ins tall the LAN driver you must first remove the curr ently installed driver.

1. Insert the DVD-ROM Driver into your DVD-ROM drive.

2. Click “Start” and Select “Run”.

3. Type the following: D:\Driver\LAN\Setup.exe (I f D is not your DVD-ROM drive, substitute D with the correct drive letter).

4. Click on “Setup” to begin the Installation Wizard.

5.

6.

Follow the Wizard’s on-screen instructions to complete th e installation.

Restart the system.

67

Installing the USB20 Driver for WinXP

To ins tall the USB20 driver you must first remov e the currently installed driver.

1. Insert the DVD-ROM Driver into your DVD-ROM drive .

2.

3.

Click “Start” and Select “Run”.

Type the following: D:\Driver\USB20\USB20.exe (If D is not your DVD-ROM drive, substitute D with the correct drive letter).

4. Click on “USB20” to begin the In stallation Wizard.

5.

6.

Follow the Wizard’s on-screen instructions to complete th e installation.

Restart the system.

Please note that Window XP Service Pack 1 provides builtin driver for USB 2.0. Do not inst all USB 2.0 driver from driver CD if you already have Wi ndows XP Service Pack 1

Installing the IR Driver for WinXP

To install the IR driver you must first remove the currently installed driver.

1. Insert the DVD-ROM Driver into your DVD -ROM drive.

2. Click “Start” and Select “Run”.

3. Type the following: D:\Driver\IR\Setup.exe (If D is not y substitute D with the correct dri ve letter). our DVD-ROM drive,

4. Click on “Setup” to begin the Installation Wizard.

5.

6.

Follow the Wizard’s on-screen instruction s to complete the installation.

Restart the system.

68

Manua

Installing the TouchPad&StickPoint Driver for WinXP

4.

5.

6.

To install the touchpad driver you must first remove the currently installed driver.

1. Insert the DVD-ROM Driver into your DVD-ROM drive.

2.

3.

Click “Start” and Select “Run”.

Type the following: D:\Driver\Touchpad&StickPoint\Setup.exe (If D is not your

DVD-ROM drive, substitute D with the correct d rive letter).

Click on “Setup” to begin the Installation Wizard.

Follow the Wizard’s on-screen instructions to complete the installation.

Restart the system.

To install the driver manually, follow the step-by-step procedures described on each individual section for a more clear installatio n.

Installation des CardBus-Treibers für WinXP

Gehe n Sie folgendermaßen vor, um den CardBus-Treiber zu inst allieren:

1. Klicken Sie unter "Start" auf da s Symbol "Arbeitsplatz". Klicken Sie auf

"Systeminformationen anzeigen ".

2.

3.

Klicken Sie im Dialogfenster "Systemeig enschaften" auf das Register "Hardware".

Klicken Sie auf die Schaltfläche "Geräte-Manager" .

4. Doppelklicken Sie auf "PCMCIA-Adapter". Doppelklicken Sie auf "Gen eric

CardBus Controller " und auf das Register "Treiber".

5. Klicken Sie auf das Register "Treiber aktualisieren" und wählen das Menüelement

69

"Software von einer Liste oder bestimmten Quelle installieren (für fortgeschrittene

Benutzer)". Klicken Sie auf „Weiter".

6. Wählen Sie das Menüelement "Folgende Quelle ebenfalls durchsuchen:" und klicken auf "Durchsuchen". Geben Sie die Position Ihres Treibers an

D:\Driver\Cardbus\ENE1410\WinXP, um mit der Installat ion fortzufahren.

Insta lling the Actiontec Combo /Wireless LAN Driver for WinXP

1. Click the "My Computer" icon and click on the "Control Pan el" item to open the

Control Panel.

2.

3.

Double click on the "System" icon. Click the "Device Manager" tab.

Click on the "Other Devices" (denoted by the yellow mark symbol), select the

"Ethernet Controller" and click on the "Properties" tab.

4. From the "Eth select the "Up ernet Controller Properties" window, click on the "Driver" tab and date Driver" button.

5. Click on the "Specify the location of the driver (Advanced)" and again click on the

"Next" button.

6. Select the "Specify a location" and click the "Browse" button to locate the disk drive of your DVD-ROM driver.

D:\Driver\MiniPCI\Actiontec\Wireless\WinXP to proceed with th e installation.

Insta lling the Accton Combo/Wireless LAN Driver for WinXP

1.

2.

3.

Click the "My Computer" icon and click on the "Control Panel" item to open the

Control Panel.

Double click on the "System" icon. Click the "Device Manag er" tab.

Click on the "Other Devices" (denoted by the yellow mark symbol), select th e

"Network Controller" and click on the "Properties" tab.

70

4. From the "Network Controller Properties" window, click on the "Driver" tab and select the "Update Driver" button.

5. Click on the "Specify the location of the driver (Advanced)" and again click o

"Next" button. n the

6. Select the "Specify a location" and click the "Browse" button to locate the di sk drive of your DVD-ROM driver.

D:\Driver\MiniPCI\Accton\wireless to proceed with the installation.

Installing the Actiontec MiniPCI Combo Card Modem Driver for

Win XP

1.

2.

3.

4.

5.

Insert the CD-ROM Driver into your CD-ROM/DVD-ROM drive.

Click “Start” and Select “Run”.

Type the following: D:\Driver\MiniPCI\Actiontec\Modem\WinXP\Setup.exe (If D is not your CD-ROM/DVD-ROM drive, substitute D with the correct drive letter).

Click on “Setup” to begin the Installation Wizard.

Follow the Wizard’s on-screen instructions to complete the installation. Restart the system.

Install ing the Modem AM303W Driver for WinXP

1. From your screen, click on the “My Computer” icon and use your mouse or touchpad right button to select the “Properties” item.

2.

3.

Click on the “Hardware” tab from the “System Properties” dialog window.

Double click “Device Manager” tab.

4.

5.

Select the “PCI Modem” in the “Modem” group (denoted by a yellow mark sy mbol).

Click the “Driver” tab then click the “Update Driver” it em.

71

6. Select the “Search for a suitable driver for my device (recommended)” item and click “Next”.

7. Click the “Browse” button and specify for the designate location of your CD driver.

(D:\Driver\MiniPCI\AM303W\WinXP).

Insta lling the Accton Combo/AC-link MODEM Driver for WinXP

1. In sert the CD-ROM Driver into your CD-ROM/DVD-ROM drive.

2. Click “Start” and Select “Run”.

3. Type the following: D:\Driver\MiniPCI\Accton\Modem\WinXP\Setup.exe (If D is not your CD-ROM/DVD-ROM drive, substitute D with the correct drive letter).

4.

5.

6.

Click on “Setup” to begin the Installation Wizard.

Follow the Wizard`s on-screen i

Restart the system. nstructions to complete the installation.

VGA Utilit ies

After you have restarted Windows, open the “Control Panel” and double click on the

“Disp lay” ic on. From the “Display Properties” window, select the “Settings” tab and click on the “Advanced” tab to enter the “Default Monitor a nd MOBILITY RADEON

8500 Properties" window.

72

You will notice three new entries have been made in the Display Properties window: ATI

Displays, ATI color, ATI OpenGL, ATI Direct 3D, ATI POWERPLAY™, ATI Overlay and ATI Options.

73

ATI Display

With ATI Display, you can connect up to three displays simultaneously to the notebook .

You can watch a DVD movie on an external television while checking email on y our notebook screen - or surf the web on a CRT monitor while working on a presentation on digital flat p anel. The option is yours with these features.

a

74

ATI Color

You can adjust the right resolution for your screen display.

75

ATI OpenGL

Play the latest and greatest OpenGL based games as well as CAD/Design programs.

76

ATI Direct 3D

An API for manipulating and displaying 3-dimensional objects.

77

ATI Options

Display all the items concerning the ATI related function.

78

ATI POWERPLAY™

79

ATI Overlay

80

Troubleshooting

7

81

This chapter describes locating and solving problems that you may encounter while using your computer.

Locating a Problem

Problems with your computer can be caused by something as minor as an unplugged power cord – or as major as a damaged hard disk. The information in this chapter is designed to help you find and solve minor problems. If you try all the suggested and you still have a problem, make a list of what steps you have taken to c

solutions orrect the problem and contact your dealer.

Successful troubleshooting is the result of careful observation, deductive reasoning, and an organized approach to solving the problem.

The problem problems and s that you will encounter can be divided into two basic

software problems. Hardware problems can be further

categories: hardware divided into electrical and mechani cal problems. You will know you have a hardware pr oblem if the screen is dark, the co mputer cannot read the disk drives, or you get an error message during the

Power-On Self Test (POST).

Software errors can occur at several levels. The ROM BIOS and the operating system can give you a large number of error messages. On top of this, each application software package has its own set of error messages. It is important to determine whether the software error message you are getting is from the application or the operating system.

Once you know this, you can look in the respective manual for a solution to the problem.

Checking Cables and Connections

Start by performing a careful visual inspection of the exterior of the computer. If no

LEDs are illuminated, make sure that your computer and its peripherals are getting power and communicating with each other properly.

To check the power cables, and connections:

1. If you have been using battery power, connect the Notebook to an external power

82

source and make sure that the battery has a charge.

2. If you are using the Notebook with the AC adapter, check the power outlet, the power cord, and any power switches that may affect your computer.

• Check th e wall outlet or power strip with an item that you know is functioning properly. A lamp or radio is a convenient item for checking the power. You may also need to check the fuses and breakers in your electric box.

• If the outlet is controlled by a wall switch, make sure that the switch is on.

• If the outlet is controlled by a dimmer switch, use a different outlet.

• If your computer is plugged into a power strip with an On/Off switch, make sure the switch is on.

3. With the computer’s power switched off, check all cable connections. If the computer is connected to any peripheral d evices, look for loose or disconnected cables. If the computer is too close to a wall, a cable connection may be loose or the cables may be crimped.

Do not substitute cables for different devices (other than the manufacturer recommended cables) even if they look

exactly alike. The wiring inside the cable may be different.

4. When you are certain that you have power available and all connections are good, turn the computer on again. If the computer still does not start, you may have a hardware problem.

The Power-On Self Test

The Power-On Self Test (POST) runs every time you turn on or reset the Notebook. The

POST checks memory, the main system board, the display, the keyboard, the disk drives, and other installed options.

83

A few seconds after you turn on your computer, a copy right message appears on your displa y screen. A memory test message appears next; as increa the test continues, memory size ses until all installed memory is tested. Normally, the only test routine visible on the screen will be the memory test.

• Error messages that indicate a failure with either the hardware, the software, or th

Basic Input/Output System (BIOS). These critical malfunctions prevent the e computer from operating at all or could cause incorrect and apparent result s. An example of a critical error is microprocessor malfunction.

• Messages that furnish important information on the power-on and boot processes

(such as memory status). These non-critical malfunctions are those that cause incorrect results that may not be readily apparent. An example of a non-cri tical error would be a memory chip failure.

In gen eral, if the POST detects a system board failure (a critical error), the computer ha lts and g enerates a series of beeps. I f failure is detected in an area other than the system board (such as and

th the screen te e display, keyboard, or an adapter card) an error message is displayed sting is stopped. It is important to remember that the POST does not t

on est all areas of th e computer, only those that allow it to be operational enough to r un diagno stic pr o gr ams.

If you r system does not successfully complete the POST, but displays a blank scree n, emits a series of beeps, or displays an error code, consult your dealer.

General Ha rdware Probl ems

A few common hardware problems and suggested solutions are presented in the table below:

Problem: The capacity of the battery is between 95 to 99% but can not fully charged.

Solution: Please discharged to less than 95% of its capacity then recharge the battery.

84

Problem: Failure in the installation of the Audio driver.

Solution: Be sure to first remove the current audio device from your system. Please follow the instruction on the installation of audio driver.

Problem: The display screen is dark

Sol io Make sure that the computer is not in Suspend mode. Check the Brightness controls for the screen. If the controls are turned too far down, the screen will be dark.

Proble m: An incorrect date and time are displayed.

Sol io Correct the date and time using the DOS DATE and TIME commands or the options i n the Setup Utility. If the date and time become incorrect after a short time, yo ur

CMOS b attery may be depleted. Contact your dealer to change the battery.

Problem: The message: “ Invalid system disk, Replace the disk, and then press any key ” appears during boot.

Solution: Check and make sure that you do not have a non-bootable floppy diskette inserted in your floppy drive. If your USB FDD is empty, you may not have an operating system installed on your drive. Contact technical support for assistance.

Problem: You hear irregular beeps during operation of the Notebook and the system halts.

Solution: The problem is beyo nd the scope of this manual. Contact technical support.

Problem: An unidentified message is displayed.

Solution: Reboot the computer and run the BIOS system setup. Confirm the Setup parameters.

If the same message is displayed after booting up again, contact technical support for assistance.

Problem: The system cannot access the DVD-ROM drive.

85

Solution: Check that a CD is properly inserted in the drive the correct program for that kind of CD. For example, the sy

. Make sure that you are using stem cannot read a data CD using an au dio program.

Problem: You cannot operate the printer.

Solution: Check the printer cable co nnection. Ensure that the printer power switch is turned on. Confirm that the printer is on-line.

Problem: You can’t save data to disk.

Solution: Ensure that the disk has been formatted.

Consult you r operating system manual for information on formatting floppy diskettes.

Problem: The diskette is write-protected.

Solution: Eject the diskette, remove the write protection, and try again.

Problem: The diskette if full.

Solution: Try using another diskette or free up some space on the diskette. The disk drive is not operating. Contact your dealer for support.

Problem: You cannot use the mouse.

• Check the cable connection.

• Ch eck the mouse with another application to see if there is a software incom patibility problem.

• If p ossible, check the mouse with another computer to see if it works. If it doesn’t operate on a different system, the mouse m ight be broken.

86

Contacting Your Dealer

If you still ha ve a problem after reading the p receding sections, the next step is to contact your dealer.

Your dealer can determine if the problem is something that requires the computer to b e taken to the shop.

Be fore you call your dealer, however, prepare t he following information:

• Ho w is your computer configure d? Your dealer needs to know what peripheral devices you are using.

• Wh at messages, if any, are on the screen?

• What software were you running at the time?

• Wh at have you done already to try t o solve the problem? If you have overlooked a step, your dealer may be able to solve the problem over the phone.

87

88

Upgrading your

System

8

Upgrading your Memory

Refer to the following instructions and illustration for information on upgrading your notebook's memory.

90

1. Turn off the computer and disconnect the AC adapter and all peripherals.

2. Turn the notebook over so that the rear ports are facing you and locate the memory module compartment.

3. Remove the screws that secure the RAM module compartment cover and set it aside in a safe place.

4. Remove the compartment cover and then angling it up and out.

5. If you need to install a higher capacity module, gently push the edge clips on both sides to release the m odule. Angle the card slightly upward and gently slide it from its edge connector slot. Store the card in the anti-static bag that contains your new module(s).

6. To install the ne w memory card, hold the card with its gold edge connector toward the edge connector slot of the compartment. To help you orient the card s, the edge connector has been made with two unequal-length sections. You will only be able to insert the card in one direction.

7.

8.

Insert the edge connector into the slot. The gold edge connector of the card should not be visible when the card is fully inserted.

Press the card downward where you should hear an audible click as the latch es of the connector secure the card in place.

9.

10.

Once the module is properly seated, you can replace the cover on this co mpartment.

Replace and tighten the screw.

The Easy to Upgrade HDD Module

The h ard drive in your notebook computer is made to be easily swapped out for upgrading .

You shou ld back up your hard drive before attempting o change the hard drive.

Make sure that before you install a new drive, all t he files in your system should be backed up.

To upgrade your Hard Drive

1.

2.

Power down the syste m completely. Turn the system over with the front of the unit facing you.

Remove the thre e screws that secure the compartment cover and set them in a safe place.

91

3. Slide the HDD cover away from the compartment.

4. The drive is attached to a special bracket that secures it to the notebook computer.

There are 4 screws hold the bracket. Remove the screws and set them in a safe place.

5.

6.

Push the HDD slightly in the direction of the arrow as shown in the illustration to release it from the pins of the drive.

Gently hold the grip of the HDD, lift it up to release from its compartment.

92

7. To install the new HDD, you will need to align the tabs on the drive bracket with the slots on the bay. Press down gently on the drive bracket until it engages with the system. Do not force the drive into place this can bend the pins on the hard drive.

8. Slide t he compartment cover into place and be sure the screw holes on the cover align completely with the screw holes in the case.

9. Secure the cover with the three screws.

CPU Upgr ade

To up grade your CPU, follow the procedures below:

1.

2.

3.

4.

5.

6.

7.

Turn the notebook over so that the rear ports are facing you.

Locate for the expansion compartment.

Unscrew and remove the cover of the CPU compartment.

Remove all the screws attached to the heatsink.

Before removing the screws, there are certain measures to followed in remo ving the heatsink

To remove the heatsink, first loosen the screw carefully.

After loosening one screw, be certain that the next to be loosen should be the screw on its adjacent side as shown on the illustration.

93

94

Be sure to loosen all the screws first before removing it totally to release the heatsink.

Failure to do so will cause a major damage to the heatsink.

8. Now you can totally remove all the screws also in that order when you first loosen the screw.

95

96

Specification

A

Detailed Notebook Specifications

General

CPU

• Intel uFCPGA478 P4/Northwood CPU, 512KB L2 cache on die, FSB=533MHz up to 3.2GHz HT

Memory

Main Me mory

• 2 e xpansion slots for 200 pin DDR module, up t o 1GB system memory

• Su pport 2.5V DDR 266/333 module

ROM

• 512KB Flash ROM

• Boot block protection

Core Logic

• SiS 645DX+962, support Hyper Threading (HT) Function

• 4X AGP bus interface

• Supports host bus at 533MHz

• AGP v2.0 compliant

• 3.3V PCI version 2.2 compliance

• ACPI v1.0b

• USB 2.0 compatible

98

• Expansion 2 slots of 200 pin DDR SDRAM module.

Mass Storage

HDD

• Support enhanced IDE (PIO mode 4) and bus master (Ultra DMA

33/66/100 mode)

• Easily upgradable 2.5" 9.5mm HDD

Module Bay

• Supports DV D-ROM/Combo/DVD Multi Drive; 5.25" 12.7mm height

• Fast IDE and ATAPI interface DVD-ROM/Combo Drive

PCMCIA Sockets

• 1 Type I I, support CardBus

Synaptics To uchPad

Support four way scrolling feature

• US/Europe, DOS/V keyboard for Japan, full size keyboard alike pitch

• 300 mm keyboard with key stroke 3.0mm

• Twe e f

• Inte al ard 101/102 desktop keyboard

• 2 sh t-c

Audio

• Dua ull ct Sound Channels

• Hardware SoundBlaster Pro for real -mode DOS legacy compatibility

99

100

• 18-bit DC & DAC resolution

• Support SPD IF out

• AC97 2.1, SP DIF, 5.1 channel support, built-in four stereo speakers

I /O Ports

• One ara llel port supported EPP/ECP (25-pin female D-connector)

• One -vi deo TV out port for TV

• One DC input port for External AC adapter (2-pin D C jack)

• One Type II PCMCIA card socket

• One ide o port for external analog VGA monitor (15-pin female D-connector)

• USB 2.0 port x 4

• MIC-in, headphone jack w/ adaptor for 5.1 channel SP/DIP support

• RJ-11 jack for Fax/Modem

• RJ-45 jack for L AN

• 1394A

Display

• 16" SXGA+/UXGA

AC Adapter

• External universal type AC adapter, 90W or 120W (for 3.0GHz CPU or above)

Smart Battery

• 12 x 18650 Li-Ion battery pack @87.02W or 95.46W (for 3.06G CPU)

• User int erchangeable

• Rem ovable and rechargeable

• Charge modes - 3.5 hours to full charge when system is off or in su spend mode

• More than 2.5 hours of battery lif e time under Ziff-Davis Inc. BatteryMark 4.0

Test with Intel 478 pin Northwood 2.0GHz CPU and 16.1" S XGA+UXGA LCD installed at 25°C

• Weight: 3.8Kg with 16.1" display panel, battery and DVD-ROM drive installed

• Size: 371mm (W) x 286.7mm (D) x 37.8/47.5mm (H)

Temperature

• Operating:

• Stora ge:

Humi dity

5°C ~ 35°C

-20°C ~ 60°C

• Op erating:

• Non-operating:

30% ~ 90% (non-condensing)

10% ~ 90% (non-condensing)

Altitude

• Operating: -200 to 10,000 feet above sea level

• Non-operating: -200 to 30,000 feet above sea level.

101

102

Options

• Li-Ion battery pack

• Factory option: Fax/Modem miniPCI card, 802.11b wireless LAN + mo dem combo miniPCI card

• Factory option: Audio DJ

• Factory option: K/B with StickPoint & dual-pointing touch pad

• Memory Extension card

• Module bay: DVD-ROM/Combo (DVD-ROM+CD-RW)/DVD Multi Drive

Accessories

• User's manual (option)

• Driver CD title

• AC adapter

• Power cord

Software Specifications

System Software

• System BIOS: Phoenix BI OS

• Support ed Operating Systems

Optional Windows XP or above version

• Standard Software Driver

VGA driver s

Audio driver

1394 driver

TouchPad&StickPoint driver

IR driver (optional)

Modem driver

LAN driver

Wireless LAN driver

CardBus driver

USB20 driver

103

advertisement

Related manuals

advertisement