TH-1040-CTS
TH-1040-CTL
TH-1040-CTSW
TH-1040-CTLW
Installation Instructions
Ceiling Tilt Short Mount / Ceiling Tilt Long Mount
Component Checklist
Hardware
Display Mounting
Screws
Mounting Plate False Ceiling Cover
Coach Screw (x4)
2.5/3/5mm
Allen Key
M4x16/25mm (x4 each)
Mounting Plate Cover
Tools Required:
•
•
•
•
•
Power drill
7mm (¼”) drill bit
12mm
(½”) masonry drill bit
Phillips head screw driver
VESA Plate
17mm
( 11 /
16
”)
Socket Wrench or Shifter
Pole Assembly
Nylon Anchor (x4)
M4/5 Spacer (x4)
M4/5/10 Washer
(x4 each)
M6/8 Spacer (x4)
(optional) Security Screw Set Screw
M5x16/25mm (x4 each)
M6x16/30mm (x4 each)
M8x16/30mm (x4 each)
IMPORTANT INFORMATION:
! IMPORTANT - Install 1040 Ceiling Tilt Mount (Short/Long) as per Installation Instructions.
! This product supports a maximum load of 25kg (55lbs).
! This product supports VESA mounting hole configurations 75x75mm, 100x100mm, 200x100mm, 200x200mm.
! The manufacturer accepts no responsibility for incorrect installation.
Step 1. Check Components
Check you have received all parts against the Component Checklist and Hardware above.
Step 2. Install Mounting Plate Step 3. Install Mounting Plate Cover
Masonry Ceiling Timber Ceiling
Nylon Anchor
Mounting Plate
M10 Washer
Coach Screw
OR
Pole Assembly
PUSH
Using the Mounting
Plate as a template, mark out and drill 4x Ø7mm
(¼”) holes, Ø12mm (½”) for masonry ceilings,
70mm (2.75”) deep.
Step 4. Attach Pole Assembly to Mounting Plate
Mounting Plate Cover
Step 5. Position Mounting Plate Cover
TWIST
Mounting Plate
3mm
Allen Key
Pole
Assembly
A.
Screw Pole Assembly into Mounting Plate by twisting top half of the
Pole Assembly only.
B.
Set Screw
Insert Set Screw into the
Mounting Plate to lock the
Pole Assembly in position.
PUSH
Mounting Plate
Cover
Pole Assembly
Step 6. Set Height of Pole
A. Whilst supporting the lower half of Pole
Assembly loosen the Socket Cap Screws (x2).
Socket Cap
Screw
ADJUST
HEIGHT
5mm Allen Key
LOOSEN
B. Slide Pole Assembly to the desired height.
C. Tighten the Socket Cap
Screws (x2) to set the height.
2.5mm
Allen Key
TIGHTEN
FIRMLY
Pole Joint
Set Screw
D. If necessary, centralise the
Pole Joint by tightening the
Set Screws (x2) to suit.
Step 8. Attach Display to Pole Assembly Step 7. Attach VESA Plate to Display
Mounting
Screws
TOP
VESA plate Spacers
(optional, for recessed mounting holes)
Choose the appropriate mounting hardware to suit the Display.
Step 9. Cable Management
A. HOOK
Security
Screw
B. PUSH
C. (optional) Once Display is attached, insert
Security Screw using
Phillips-head screwdriver
Step 10. Height Adjustment
5mm
Allen Key SLIDE
Cable
Access Port
A. Feed cables down the Pole
Assembly through the Cable
Access Port.
B. Pull cables out from lower half of the Pole Assembly and connect to Display.
Step 11. Final Adjustment
TILT
VESA Ball Mount
Tension Plate at rear
Donut
Socket Cap
Screw
A. Loosen Socket Cap
Screws (x2) on the Donut.
B. Slide the height of the
Donut as required. Tighten
Socket Cap Screws to lock.
Step 12. Install False Ceiling Cover
CLICK
False Ceiling
Cover
Lower Pole
PUSH
PAN
PORTRAIT TO
LANDSCAPE
3mm Allen Key
A. Pan, Tilt and Rotate the Display as required.
B. If necessary tighten the VESA
Ball Mount by adjusting the
Tension Plate. Using the 3mm
Allen Key adjust screws evenly.
Installation Complete
If the Lower Pole hangs below a suspended ceiling, clip the False
Ceiling Cover over the Lower Pole, and push up to the ceiling.
No portion of this document or any artwork contained herein should be reproduced in any way without the express written consent of Atdec Pty Ltd.
Due to continuing product development, the manufacturer reserves the right to alter specifications without noticed. Published 05.02.16 ©
