advertisement
AUDIO/VIDEO MULTI-CHANNEL
RECEIVER
Operating Instructions
Thank you for buying this Pioneer product.
Please read through these operating instructions so you will know how to operate your model properly. After you have finished reading the instructions, put them away in a safe place for future reference.
In some countries or regions, the shape of the power plug may sometimes differ from that shown in the explanatory drawings. However, the method of connecting and operating the unit is the same.
This product complies with the Low Voltage
Directive (73/23/EEC, amended by 93/68/EEC), EMC
Directives (89/336/EEC, amended by 92/31/EEC and
93/68/EEC).
CAUTION:
THE STANDBY/ON BUTTON IS SECONDARY CONNECTED
AND THEREFORE DOES NOT SEPARATE THE UNIT FROM
MAINS POWER IN STANDBY POSITION. THEREFORE INSTALL
THE UNIT SUITABLE PLACES EASY TO DISCONNECT THE
MAINS PLUG IN CASE OF THE ACCIDENT. THE MAINS PLUG
OF UNIT SHOULD BE UNPLUGGED FROM THE WALL SOCKET
WHEN LEFT UNUSED FOR A LONG PERIOD OF TIME.
H017BEn
This product is for general household purposes. Any failure due to use for other than household purposes
(such as long-term use for business purposes in a restaurant or use in a car or ship) and which requires repair will be charged for even during the warranty period.
K041_En
Operating Environment
H045 En
Operating environment temperature and humidity:
+5 ° C – +35 ° C (+41 ° F – +95 ° F); less than 85%RH (cooling vents not blocked)
Do not install in the following locations
• Location exposed to direct sunlight or strong artificial light
• Location exposed to high humidity, or poorly ventilated location
2
En
VENTILATION:
When installing this unit, make sure to leave space around the unit for ventilation to improve heat radiation (at least 20 cm at top, 50 cm at rear, and 10 cm at each side).
WARNING:
Slot and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating, to prevent fire hazard, the openings should never be blocked and covered with items, such as newspapers, tablecloths, curtains, etc. Also do not put the apparatus on the thick carpet, bed, sofa, or fabric having a thick pile.
H040 En
Features
Compatibility with the Home
Theater Formats
Dolby Digital, DTS Sound Decoders
These highly evolved multichannel sound formats are the heart of home theater. They deliver realistic multichannel sound that can turn any living room into a theater, reproducing all the sound effects of the original movie. The VSX-C100 has the flexibility to decode all these formats.
Dolby Pro Logic II Decoder
The VSX-C100 reproduces this industry-leading format with excellent clarity. With it you can get multichannel surround sound even from two channel and Dolby
Surround sources.
Easy-to-use Remote Control
This new remote control is extremely convenient to use.
One button is dedicated to one task in the control of the receiver, eliminating confusing buttons whose purpose are unclear. In addition, this remote can be used to operate a variety of other components simply by recalling the appropriate setup codes.
Easy Setup for Quick Home Use
This receiver features an automatic setup function that senses which speakers you have hooked up and automatically sets the receiver for proper surround sound. Thus, you can start enjoying home theater immediately after hooking up your speakers and components, without worrying about difficult setup procedures.
Home Theater Listening Modes
Custom Designed Listening Modes (p.33)
These modes enhance the sound of sources from movies and music to TV and video games for a more dramatic effect. These are each designed to accentuate specific sound qualities, giving the listener a wide range of possibilities.
VIRTUAL Mode (p.33)
This especially designed listening mode uses only two channels but through sound imaging imitates a full surround sound. It allows you to experience surround sound with only two speakers.
PHONES SURROUND Mode (p.33)
This new headphone mode allows the user to get a surround-like sound while listening on headphones designed to accommodate this technology.
Sound Modes (p.35)
This unit also has especially created Sound Modes that can enhance your listening experience and bring out the best in each soundtrack. Each mode is designed to bring out a specific quality of the soundtrack or balance the sound. The NATURAL corrects the frequencies for small speakers to achieve better theater-like surround sound.
The MIDNIGHT listening mode allows you to obtain excellent surround sound effects even when listening at low volumes, something that was previously impossible.
The MANNER mode provides good sound by smoothing out harsh noises in the soundtrack. This is achieved by reducing the bass and treble. The BRIGHT mode flattens out the total frequency output to match the charactersics of the front speakers. The S.BASS mode gives you added bass for that driving punch that really livens up your music or makes a film more realistic.
The Energy-saving Design
This unit is designed to use less than 1 W of energy when the receiver is in standby mode.
Manufactured under license from Dolby Laboratories. "Dolby", "Pro Logic", and the double-
D symbol are trademarks of Dolby Laboratories.
“DTS” and “DTS Digital Surround” are trademarks of Digital Theater Systems, Inc.
TruSurround and the ® symbol are trademarks of SRS Labs, Inc. TruSurround technology is incorporated under license from SRS
Labs, Inc.
3
En
4
En
Contents
Congratulations on buying this fine Pioneer product.
Please read through these operating instructions so you will know how to operate your model properly. After you have finished reading the instructions, put them away in a safe place for future reference.
01
Contents 4
Quick Start Guide 5
Introductory Information 9
Checking the Supplied Accessories 9
When Making Cable Connections 9
Operating Range of Remote Control Unit 10
Maintenance of External Surfaces 10
02 Connecting Your Equipment 11
Coaxial Cords/Optical Cables 11
Connecting a DVD Player & TV 12
Connecting a Digital Tuner/Set Top Box 13
Connecting a TV with an Internal Digital Tuner 14
Connecting Video Components 14
Operating other Pioneer Components with this
07
08
Using the Tuner 36
Tuning Directly to a Station 37
Recalling Memorized Stations 38
The Receiver’s Internal Program
Using Other Functions 43
Changing the Display Brightness (DIMMER button) 43
Default Settings for the Receiver 45
03
04
Displays & Controls 20
Basic Playback 24
Checking the Settings on Your DVD (or other)
Program Format/Speaker Channel Indicators 24
09 Controlling the Rest of Your System 46
Changing the Remote Control Mode 46
CD/MD/CD-R/VCR/DVD/LD/DVD recorder/
Cable TV/Satellite TV/Digital TV/TV Controls
10 Additional Information 54
05 Fine Tuning Your Surround Sound 26
Personalizing Your Surround Sound 27
Setting the Volume Level of Each Channel 32
06 Playback Modes 33
11 Techno Know How 57
Understanding DVD Packaging 57
Quick Start Guide
Home Theater: The Basics
Most consumers are used to using stereo equipment to listen to music but many people are not used to home theater systems that give you many more options when listening to soundtracks. In fact, home theater is not really complicated and this little guide should give you an understanding of basics.
The main reasons why it seems so difficult is that there are three different factors involved in home theater and each will contribute to what kind of sound you get.
These factors are:
1) The equipment you are using for you home theater set up. Particularly important is the number of speakers you are using. We call this your speaker configuration. The default settings should be fine in most cases.
2) The 'source' material you are using. This is the actual product (like a DVD) or broadcast (like cable TV) you are listening to/watching. We call this the source.
3) The last factor is the listening mode you choose on the VSX-C100 receiver. These are explained below and in subsequent chapters but most likely the default setting will be fine.
Let's start with the home theater set up you have in your home.
Your Home System
The heart of your system is the VSX-C100 receiver and it is very flexible in getting you theater-like surround sound.
You can use this receiver with anywhere from two to five speakers (front left, front right, center, surround left and right) and a subwoofer to get home theater surround sound. However we recommend you use five speakers. If you only have two speakers choose the Listening mode that offers surround sound for your home setup. Also, a DVD player is essential for home theater and you can also hook up satellite or cable TV tuner to this receiver and get a more home theater like sound from those programs.
The Source Material
DVDs have become the basic source material for home theater because they offer excellent sound and picture quality, allow users to choose the movies they want, and are easy to store, etc. You can also enjoy home theater with other sources, such as digital satellite TV, cable TV and VHS videotapes. The important part here is all these sources have soundtracks recorded on them with various kinds of technology (this is called the sound encoding). Home theater sources are recorded (encoded) with multiple sound channels, that is discrete parts of the overall sound. CDs (which are stereo sources) work the same way but they only have two sound channels, the left channel and the right channel.
These two channels carry different parts of the soundtrack and mix together when you hear it to make an enjoyable, stereo sound. The same idea applies to home theater sources except home theater sources are recorded with multichannels, that is, more than two channels. For example, Dolby Pro Logic encoding has four channels (front left, front right, center and a single channel for both surround speakers), Dolby Pro Logic II, Dolby Digital and DTS encoding usually have six channels (front left, front right, center, surround left and right and a channel that powers the subwoofer). Since the subwoofer channel is only for bass sounds this multichannel set up has been named 5.1
channel sound. These multiple channels are what create a surround sound effect and give you a similar experience of that of a movie theater. It is important you consult the manual that came with your DVD player as well to make sure the player is outputting a surround soundtrack and all the other settings are appropriate for home theater.
The Listening Modes
This receiver has many different listening modes and they are designed to cover all the speaker configurations and types of sources you might be using. In general, if you follow the recommend advice and have five speakers hooked up in most cases the AUTO listening mode is the easiest way to get realistic home theater sound. This is the default setting so you don't have to do anything. Other possibilities (like listening to a stereo CD with all five speakers or, conversely taking a stereo source and it getting multichannel home theater-like sound) are explained in Listening modes (page 33).
These are the three basic factors that contribute to your home theater sound. The easiest thing is to hook up five speakers and simply play your DVDs with AUTO mode. This will give you realistic and enjoyable home theater sound.
5
En
6
En
Quick Start Guide
No Frills Setup
This receiver was designed with the easiest possible setup in mind so if you just want to hook up your equipment and start enjoying quality home theater movies follow the four steps below and use these easy settings on the VSX-C100.
In most cases you can leave the receiver in the default settings.
Default Settings:
• Speaker Setting: Automatically sensed by the receiver
• Input Setting: DVD
• Signal Select: AUTO
• Listening Mode: AUTO
• Sound Mode: NATURAL
1) Hook up your DVD player, speakers, subwoofer and TV.
Connect your DVD player to this unit using either the coaxial digital terminal or the optical digital terminals, depending on which type of digital terminal your DVD has. The quality of these two types of connection is the same so it’s simply a matter of matching like with like, and you don’t need to do both. It is easiest, however, if you follow this receiver’s default settings and connect your DVD player to coaxial terminal. If your DVD player does not have an coaxial terminal, use one of the optical terminal to hook it up to this receiver. (In this case you need to assign the
DVD function to that terminal. See p.31 in order to do this.) Follow the diagram below to hook up your DVD player to either the coaxial or optical terminal(s). Then, hook up the speakers you want to use with this receiver. This receiver can be used with just two speakers but it’s better to have five speakers to get accurate surround sound. See pages 16-17 for more details on connecting your speakers. Next, hook up your powered subwoofer, if you have one.
For all speakers make sure to connect the positive (+) and negative (–) terminals on the receiver and speakers with the same wire (positive to positive, negative to negative).
Before hooking up your speakers affix the color-coded sticker with the appropriate name (for example,
“FRONT R”) to the speaker wire so you always know which speaker that wire is connected to.
T V/
SAT
(DVD)
OPT1
DVR /
VCR
OPT2
DVD
( T V /
S AT )
COA X
DIGITAL IN
T V/
SAT
IN
DVR /
VCR
IN
DVD
IN
R
AUD IO
L
1
MONITOR
OUT
2
R
F M UNBAL75
Ω
AM LOOP
ANTENNA
L
VIDEO
DVR /
VCR
OUT
AUDIO
Coaxial cable
(sold separately)
Optical cable
(sold separately, don’t pinch or bend cable sharply)
Audio cord
(sold separately)
SUB
WOOFER
OUT
R
FRONT
L
SPEAKERS
CENTER R
SURROUND
L
While pressing down the speaker tab push the speaker wire into the terminal and release speaker terminal tab.
IN OUT
CONTROL
Speaker wire
(sold separately)
AC IN
LINE LEVEL
DIGITAL AUDIO OUT
COAXIAL
OPTICAL
STANDBY/ON
7 8
OPEN/
CLOSE
0
3 Î
DVD Player
(DV-454, etc.)
When you’re hooking up your subwoofer make sure its power cord is disconnected.
Front R
(R)
Powered
Subwoofer (SW)
Front L
(L)
Center
(C)
Surround R
(RS)
Surround L
(LS)
If you only hook up two speakers set the Listening mode to one of the modes for two channel outputs.
Quick Start Guide
T V/
SAT
(DVD)
OPT1
DVR /
VCR
OPT2
DVD
( T V /
S AT )
COA X
DIGITAL IN
T V/
SAT
IN
DVR /
VCR
IN
DVD
IN
R
AUD IO
L
Video cord
(sold separately)
Video cord
(sold separately)
1
MONITOR
OUT
2
R
F M UNBAL75
Ω
AM LOOP
ANTENNA
L
VIDEO
DVR /
VCR
OUT
AUDIO
SUB
WOOFER
OUT
MONITOR IN
R
FRONT
L
SPEAKERS
CENTER R
SURROUND
L
IN OUT
CONTROL
AC IN
STANDBY/ON
S
VIDEO OUT
1
4
¡
¢ 7 8
OPEN/
CLOSE
0
3 Î
DVD Player
(DV-454, etc.)
TV
To wall outlet
Power cord
Lastly, hook up your DVD player to the DVD IN VIDEO and your TV to the MONITOR OUT VIDEO terminals as shown above and plug in the receiver’s power cord to a power outlet.
Automatic speaker setup (receiver automatically configures Front, Center, Surround speakers and Subwoofer)
Once you have completed the above tasks, the receiver will automatically detect which speakers you have connected and configure your speaker settings according to that. You don’t have to do anything. This setup establishes the size and configuration of the speaker system you have connected and is the easy way to setup your speakers for surround sound. If you don’t have surround speakers or want to make more exact speaker settings, go to page 27.
The Automatic speaker setup will give you acceptable surround sound.
2) Turn on the power on the receiver, your DVD player, your powered subwoofer and TV.
• Make sure your TV is set to the receiver. If it is not, check the input jack this receiver is hooked up to on your TV and consult the manual that came with the TV to figure out the proper TV setting.
• Confirm that DVD appears in the receiver’s display, indicating that the receiver is set to the DVD input. If it does not, press the DVD button to set the receiver to DVD input.
3) Confirm the settings on your DVD player are correct for the source you want to play.
Make sure your DVD player is outputting a digital signal and choose the soundtrack (Dolby Digital, DTS, etc.) that you want to hear. If you are unsure about your DVD player’s settings, see page 24 for more information and/or consult the manual that came with your DVD player.
4) Play a source (like a DVD) and adjust the volume to your liking.
You are now ready to experience home theater with your new surround sound system.
7
En
8
En
Quick Start Guide
Advanced/Customized Settings
If you want to customize your home theater to your environment, equipment or personal tastes, many settings are available. One of the most important advanced settings, called Room Setup, establishes the distances between your speakers and your normal listening position (as well as volume levels, etc.). Making this setting should improve your surround sound. Room Setup is explained on page 26. After that you could go on to fine tune your surround sound for maximum sound quality. These settings start on page 27.
The VSX-C100 has many different listening modes to accommodate many different kinds of sources, speaker configurations and sound reproduction. Experiment with these features to figure out what suits your tastes.
The listening mode explanations and settings start on page 33.
The above is a quick guide to getting you started with your home theater system and a few setup suggestions. It is a good idea, however, to read this manual in its entirety so you understand what you can do with the VSX-C100 and the possibilities of home theater in general. You may find many hints in these explanations that help you get better sound and let you operate all your equipment more effectively.
Introductory Information
Checking the Supplied
Accessories
Please check that you've received the following supplied accessories:
• AM loop antenna
• FM wire antenna
• Power cord
• Dry cell batteries (AA Size / IEC R6P) x2
• Remote control unit
• Operating instructions
• Speaker cord labels
• Don’t place anything on top of the receiver except for a Pioneer DV-454, 350, 444 or 545 DVD player. If you do place one of these pieces of equipment on top of the receiver be sure to leave the ventilation space over it as prescribed above.
• The receiver may become hot while in use, please take care around it.
Installing the Receiver
• When installing this unit, make sure to put it on a secure and level plane that is stable.
• Don’t place it on the following places:
– on a color TV (the screen may distort)
– near a cassette deck (or close to a device that gives off a
magnetic field) This may interfere with the sound.
– in direct sunlight
– in damp or wet areas
– in extremely hot or cold areas
– in places where there is a vibration or other movement
– in places that are very dusty
– in places that have hot fumes or oils (such as a kitchen)
When Making Cable
Connections
Be careful not to arrange cables in a manner that bends the cables over the top of this unit. If the cables are laid on top of the unit, the magnetic field produced by the transformers in this unit may cause a humming noise to come from the speakers.
Ventilation
• When installing this unit, make sure to leave space around the unit for ventilation to improve heat dispersal (at least 20 cm at the top, 50 cm at the rear, and 10 cm at each side). If not enough space is provided between the unit and walls or other equipment, heat will build up inside, interfering with performance and/or causing malfunctions. See below for exceptions to this.
• If using a rack to hold the receiver make sure the back of the rack and the left side are open.
• Also, if you’re using a case with glass doors, leave the glass doors open when using the receiver.
• Do not place on a thick carpet, bed, sofa or fabric having a thick pile. Do not cover the receiver with fabric or other covering. Anything that blocks ventilation will cause the internal temperature to rise, which may lead to breakdown or fire hazard.
Cassette deck placement
Depending on where the cassette deck is placed, noise may occur during playback of your cassette deck which is caused by leakage flux from the transformer in the receiver. If you experience noise, move the cassette deck farther away from the receiver.
Storing optical cable
When storing optical cable, coil loosely as shown below.
The cable may be damaged if bent around sharp corners.
01
more
+ than =
(15 cm)
9
En
Introductory Information
Loading the Batteries
The remote control operates on two AA batteries
(supplied).
1
2
Maintenance of External
Surfaces
• Use a polishing cloth or dry cloth to wipe off dust and dirt.
• When the surfaces are dirty, wipe with a soft cloth dipped in some neutral cleanser diluted five or six times with water, and wrung out well, and then wipe again with a dry cloth. Do not use furniture wax or cleansers.
• Never use thinners, benzine, insecticide sprays or other chemicals on or near this unit, since these will corrode the surfaces.
3
10
En
CAUTION:
Incorrect use of batteries may result in such hazards as leakage and bursting. Observe the following precautions:
• Never use new and old batteries together.
• Insert the plus and minus sides of the batteries properly according to the marks in the battery case.
• Batteries of the same shape may have different voltages. Do not use different batteries together.
• When disposing of used batteries, please comply with governmental regulations or environmental public institution’s rules that apply in your country or area.
Operating Range of the
Remote Control Unit
The remote control may not work properly if:
• There are obstacles between the remote control and the receiver's remote sensor.
• Direct sunlight or fluorescent light is shining onto the remote sensor.
• The receiver is located near a device that is emitting infrared rays.
• The receiver is operated simultaneously with another infrared remote control unit.
30
30
7m
Connecting Your Equipment
Audio/Video Cords
Use audio/video cords (not supplied) to make analog audio and video connections.
Connect red plugs to R (right), white plugs to L (left), and the yellow plugs to VIDEO.
Be sure to insert completely.
R
L
VIDEO
Coaxial Cords/Optical Cables
Commercially available digital audio coaxial cords
(standard video cords can also be used) or optical cables
(not supplied) are used to connect digital components to this receiver.
Be sure to insert completely and in the case of the optical cable, right-side up. If it is inserted improperly it can break the shutter on the optical terminal (this won't, however, affect the connection or insertion of an optical cable).
Coaxial cord
(or standard composite video cord)
Optical cable
02
11
En
12
En
Connecting Your Equipment
Before making or changing the connections, switch off the power and disconnect the power cord from the AC wall outlet.
Connecting a DVD Player & TV
In order to play PCM/ 2 Digital/DTS multichannel soundtracks, you need to make digital audio connections.
Connect your DVD player to this unit using either the coaxial digital terminal or the optical digital terminals, depending on which type of terminal your DVD has. The quality of these two types of connection is the same so it’s simply a matter of matching like with like. It is easiest, however, if you follow this receiver’s default settings and connect your DVD player to coaxial terminal. If your DVD player does not have an coaxial terminal, use the optical terminal to hook it up to this receiver. In this case you need to assign the DVD function to that terminal. See p.31 in order to do this. Follow the diagram below to hook up your DVD player to either the coaxial or optical terminal(s).
Also, connect your TV to this receiver as shown below.
The basic default settings for the DIGITAL IN terminals are as follows: COAX: DVD; OPT. 1: TV/SAT; OPT. 2: DVR. If you need to use an optical terminal for your DVD use OPT.1. In this case, assign your coaxial terminal to TV/SAT (see p.31) and the optical default settings change to: OPT. 1: DVD; OPT. 2: DVR.
STANDBY/ON
DVD Player (DV-454, etc.)
OPEN/
CLOSE
0
3 Î ¡
¢ 7 8
Optical cable
(sold separately, don’t pinch or bend cable sharply)
DIGITAL AUDIO OUT
COAXIAL
OPTICAL
Coaxial cable (sold separately)
ANALOG OUT
R L
S
VIDEO OUT
Video cord
(sold separately)
T V/
(DVD)
OPT1
DVR /
VCR
OPT2
DVD
( T V /
S AT )
COA X
DIGITAL IN
T V/
SAT
IN
DVR /
VCR
IN
DVD
IN
R
AUD IO
L
Why you need an analog connection as well as a digital one:
• If you don’t have an digital output on your DVD player you will need to use the analog connection shown here.
• If you want to get an audio signal from the VCR out you need an analog connection.
• If you want to use your DVD player for karaoke you need an analog connection.
1
MONITOR
OUT
2
R
F M UNBAL75
Ω
AM LOOP
ANTENNA
L
VIDEO
DVR /
VCR
OUT
AUDIO
R
FRONT
L
SPEAKERS
CENTER R
SURROUND
L
SUB
WOOFER
OUT
Video cord (sold separately)
MONITOR IN
TV
Connecting Your Equipment
Before making or changing the connections, switch off the power and disconnect the power cord from the AC wall outlet.
Connecting a Digital Tuner/Set Top Box
If you have an external digital tuner (like a set top box for satellite or cable TV) you need to connect it to either the optical digital terminals or the coaxial digital terminal in order to play digital cable/satellite broadcasting. The quality of these two types of connection is the same so it’s simply a matter of matching like with like. It is easiest, however, if you follow this receiver’s default settings and connect your cable/satellite tuner (or TV/SAT as it’s called on the remote control) to optical terminal 1. If your TV/SAT does not have an optical terminal, use the coaxial terminal to hook it up
(consult the DVD hook up information on the previous page). In this case you need to assign the TV/SAT function to that terminal. See p.31 in order to do this. Follow the diagram below to hook up your TV/SAT to either the optical or coaxial terminal.
Make sure you use a digital connection as well as an analog one for the audio on the cable/satellite tuner, as pictured below.
The basic default settings for the DIGITAL IN terminals are as follows: COAX: DVD; OPT. 1: TV/SAT; OPT. 2: DVR. If you need to use the coaxial terminal for your TV/SAT, then assign the coaxial terminal to TV/SAT. The digital terminals settings change to: COAX: TV/SAT; OPT. 1: DVD; OPT. 2: DVR. (see p.31)
T V/
SAT
(DVD)
OPT1
DVR /
VCR
T V/
SAT
IN
OPT2
DVD
( T V /
S AT )
DVR /
VCR
IN
Optical cable (sold separately, don’t pinch or bend cable sharply)
COA X
DIGITAL IN
DVD
IN
Coaxial cable
(sold separately)
R
AUD IO
L
1
MONITOR
OUT
2
R
F M UNBAL75 Ω
AM LOOP
ANTENNA
L
VIDEO
DVR /
VCR
OUT
AUDIO
Video cord (sold separately)
Audio cord
(sold separately)
Match the shape of terminal and the optical plug.
R L
AUDIO OUT DIGITAL OUT VIDEO OUT
SUB
WOOFER
OUT
R
FRONT
SPEAKERS
L CENTER R
SURROUND
L
Digital Set Top Box
Why you need an analog connection as well as a digital one:
• If you don’t have an digital output on your TV tuner you will need to use an analog connection.
• If the program you want to watch isn’t output from the digital terminals you need an analog connection.
• If you want to get a signal from a video deck instead of a TV tuner you need an analog connection.
13
En
Connecting Your Equipment
Before making or changing the connections, switch off the power and disconnect the power cord from the AC wall outlet.
Connecting a TV with an Internal Digital Tuner
If you have an TV with an internal digital tuner follow the directions above for an external digital tuner and in addition hook up your TV, if you have not already done so when you hooked up your DVD player (see the previous page). Make sure you use a digital connection as well as an analog one for the audio, as pictured below.
R
FRONT
L
SPEAKERS
CENTER R
SURROUND
L
T V/
SAT
(DVD)
OPT1
DVR /
VCR
OPT2
DVD
( T V /
S AT )
COA X
DIGITAL IN
T V/
SAT
IN
DVR /
VCR
IN
DVD
IN
R
AUD IO
L
1
MONITOR
OUT
2
R
F M UNBAL75 Ω
AM LOOP
ANTENNA
L
VIDEO
DVR /
VCR
OUT
AUDIO
SUB
WOOFER
OUT
Match the shape of terminal and the optical plug.
Optical cable (sold separately, don’t pinch or bend cable sharply)
Coaxial cable (sold separately)
Audio cord
(sold separately)
DIGITAL OUT
ANALOG OUT
14
En
TV with an internal digital tuner
Connecting Video Components
Connect your video components to the terminals as shown below.
If you have a Digital Video Recorder (a DVR) you need to connect it digitally to either the optical digital terminals or the coaxial digital terminal in order to play and/or record multichannel sound. The quality of these two types of connection is the same so it’s simply a matter of matching like with like and using the available terminal(s) after you’ve hooked up your DVD player and cable/satellite/TV tuner.
Basically the easiest way to connect a DVR is to follow this receiver’s default settings and connect your cable/satellite tuner (or TV/SAT as it’s called on the remote control) and DVR to optical terminals 1 and 2 respectively, and connect the DVD to the coaxial terminal.
If this isn’t possible due to the types of terminals each component is equipped with, then you need to figure out which component will be used for the coaxial terminal and assign it properly (see p. 31). After that follow the optical terminal defaults (as below).
If you connected the coaxial terminal to DVD and thus left it on the default DVD setting the optical terminals default settings are:
OPT. 1: TV/SAT
OPT. 2: DVR
If you assigned the coaxial terminal to TV/SAT the optical terminals default settings are:
OPT. 1: DVD
OPT. 2: DVR
All video decks (both DVRs and VCRs) should be hooked up with analog connections as well. If you want to record programs it is necessary to connect to the DVR/VCR IN AUDIO terminals as shown next page.
Connecting Your Equipment
T V/
SAT
(DVD)
OPT1
DVR /
VCR
OPT2
DVD
( T V /
S AT )
COA X
DIGITAL IN
T V/
SAT
IN
DVR /
VCR
IN
DVD
IN
R
AUD IO
L
Optical cable (sold separately, don’t pinch or bend cable sharply)
OPTICAL COAXIAL
DIGITAL OUT
1
MONITOR
OUT
2
VIDEO
DVR /
VCR
OUT
R
AUDIO
F M UNBAL75 Ω
AM LOOP
ANTENNA
L
Audio/video cord
(sold separately)
SUB
WOOFER
OUT
VIDEO
L
OUTPUT
R
INPUT 2
/AUTO REC
AUDIO
STANDBY/ON
OPEN
FL OFF
FL DIMMER
2
DIGITAL
DISCNAVI
Î
DVD
TIMER
AUTO REC
OPEN/CLOSE
0
FUNCTION
DVD RECORDER DVR-7000
SMART JOG
7
STOP
3
PLAY
8
PAUSE
REC
DVD Recorder (DVR-7000, etc.)
R
FRONT
L
SPEAKERS
CENTER R
SURROUND
L
Audio/video cord
(sold separately)
IN OUT
CONTROL
You can only record audio signals from video components hooked up with analog connections.
If the input component and the receiver are only connected with an digital cable (coaxial or optical), which is for audio, you need to connect analog video and audio cables in order to be able to record video programs with soundtracks.
Front
Select the component hooked up to the Front video connections with the FRONT button on the remote control or front panel.
FRONT INPUT
STANDBY/ON
PHONES
VIDEO L AUDIO R
DIGITAL IN
INPUT SIGNAL
2
DIGITAL
DTS AUTO
SURROUND MODE
PHONES
/VIRTUAL
2
PRO LOGIC II
ADVANCED
SOUND
MODE
VIDEO IN/OUT AUDIO IN/OUT
Match the shape of terminal and the optical plug.
COLOR BRIGHT MONITOR
DIGITAL OUT (OPTICAL)
PHONES ON/OFF HOLD
Portable DVD Player (etc.)
15
En
Connecting Your Equipment
Before making or changing the connections, switch off the power and disconnect the power cord from the AC wall outlet.
Connecting Speakers
A full complement of five speakers is shown here but, naturally, everyone’s home setup will vary. Simply connect the speakers you have in the manner described below. The receiver will sense which speakers you have hooked up. The receiver will work with just two stereo speakers (called “Front” speakers in the diagram) but we recommend you use five speakers. If you don’t hook up surround speakers you need to adjust the Listening mode settings (see p. 33).
Make sure you connect the speaker on the right to the right terminal and the speaker on the left to the left terminal.
Also make sure the positive and negative (+/–) terminals on the receiver match those on the speakers.
• Use speakers with a nominal impedance of 6
Ω
to 16
Ω
.
Before hooking up your speakers affix the color-coded stickers with the appropriate names (for example,
“FRONT R”) to the speaker wire so you always know which speaker each wire is connected to.
T V/
SAT
(DVD)
OPT1
DVR /
VCR
OPT2
DVD
( T V /
S AT )
COA X
DIGITAL IN
IN
DVR /
VCR
IN
DVD
IN
R
AUD IO
L
1
MONITOR
OUT
2
R
F M UNBAL75
Ω
AM LOOP
ANTENNA
L
VIDEO
DVR /
VCR
OUT
AUDIO
SUB
WOOFER
OUT
R
FRONT
L
SPEAKERS
CENTER R
SURROUND
L
While pressing down the speaker tab push the speaker wire into the terminal and release speaker terminal tab.
AC IN
IN OUT
CONTROL
Audio cord
(sold separately)
Speaker wire
(sold separately)
16
En
LINE LEVEL
When you’re hooking up your subwoofer make sure its power cord is disconnected.
Powered
Subwoofer (SW)
Front R
(R)
Front L
(L)
Center
(C)
Surround R
(RS)
Surround L
(LS)
Speaker terminals
Use good quality speaker wire to connect the speakers to the receiver.
1 Twist about 10 mm of bare wire strands together.
2 Push in the speaker terminal tab and insert the wire.
3 Release speaker terminal tab, it should snugly grip the speaker wire.
ª
·
10 mm
Caution:
Make sure that all the bare speaker wire is twisted together and inserted fully into the speaker terminal. If any of the bare speaker wire touches the back panel it may cause the power to cut off as a safety measure.
Hints on Speaker Placement
Speakers are usually designed with a particular placement in mind. Some are designed to be floor standing, while others should be placed on stands to sound their best. Some should be placed near a wall; others should be placed away from walls. Follow the guidelines on placement that the speaker manufacturer provided with your particular speakers to get the most out of them.
• Place the front left and right speakers at equal distances from the TV.
• When placing speakers near the TV, we recommend using magnetically shielded speakers to prevent possible interference, such as discoloration of the picture when the TV is switched on. If you do not have magnetically shielded speakers and notice discoloration of the TV picture, move the speakers farther away from the TV.
• Install the center speaker above or below the TV so that the sound of the center channel is localized at the TV screen.
CAUTION!
If you choose to install the center speaker on top of the TV, be sure to secure it by suitable means to reduce the risk of damage or injury resulting from the speaker falling from the TV in the event of external shocks such as earthquakes.
• If possible, install the surround speakers slightly above ear level.
• Try not to install the surround speakers farther away from the listening position than the front and center speakers. Doing so can weaken the surround sound effect.
• Install the subwoofer on the same plane as the front speakers.
Connecting Your Equipment
Overhead view of speaker set up
Front Left (L) Center (C)
Front
Right (R)
Subwoofer
(SW)
Surround
Left (LS)
Listening Position
3-D view of speaker set up
Surround
Right (RS)
To achieve the best possible surround sound, install your speakers as shown on the right. Be sure all speakers are installed securely to prevent accidents and improve sound quality.
17
En
Connecting Your Equipment
Before making or changing the connections, switch off the power and disconnect the power cord from the AC wall outlet.
Connecting Antennas
Connect the AM loop antenna and the FM wire antenna as shown below. To improve reception and sound quality, connect external antennas (see Using External Antennas, below).
T V/
SAT
(DVD)
OPT1
DVR /
VCR
OPT2
DVD
( T V /
S AT )
COA X
DIGITAL IN
T V/
SAT
IN
DVR /
VCR
IN
DVD
IN
R
AUD IO
L
1
MONITOR
OUT
2
R
F M UNBAL75
Ω
AM LOOP
ANTENNA
L
VIDEO
DVR /
VCR
OUT
AUDIO
SUB
WOOFER
OUT
R
FRONT
L
SPEAKERS
CENTER R
AM loop antenna
Assemble the antenna and connect to the receiver.
Attach to a wall, etc. (if desired) and face in the direction that gives the best reception.
AM Antenna connectors
Twist the exposed wire strands together push the tab back, insert into the hole and release connector.
18
En
Using External Antennas
To improve FM reception
Connect an external FM antenna.
PAL connector
75
Ω
coaxial cable
F M UNBAL75
Ω
AM LOOP
ANTENNA
10mm
FM wire antenna
Connect the FM wire antenna and fully extend vertically along a window frame or other suitable area.
To improve AM reception
Connect a 5-6 m length of vinyl-coated wire to the AM antenna terminal without disconnecting the supplied AM loop antenna.
For the best possible reception, suspend horizontally outdoors.
Outdoor antenna
Indoor antenna
(Vinyl-coated wire)
5–6m
F M UNBAL75
Ω
AM LOOP
ANTENNA
Connecting Your Equipment
Operating other Pioneer Components with this Unit’s Sensor
By connecting a control cord to the CONTROL terminals of the respective equipment, you can control several Pioneer components using one remote sensor. Following the diagram below you will see that one component feeds the
CONTROL OUT terminal and on the other end another component is connected to the CONTROL IN terminal. The component that is the end point (the one that has a cord hooked up to its CONTROL OUT only) it is the component whose sensor you will use. Point the remote control at that sensor when you want to operate the any of the equipment connected by this system. In the example below you would point the remote control unit towards the remote sensor of the equipment on the left.
• You can also control Pioneer components by pointing the receiver's remote control directly at the component.
This type of operation does not require control cords. See page 47 for more information.
• To use this kind of remote control you have to hook up a control cord AND the have the component and receiver hooked up with analog RCA audio/video cords as well (see pages 12–15).
Point remote control towards remote sensor of component that only has a cord connected to its CONTROL OUT terminal
Components with an CONTROL terminals
Mono mini plug
(optional)
R
FRONT
L
SPEAKERS
CENTER R
SURROUND
L
T V/
SAT
(DVD)
OPT1
DVR /
VCR
OPT2
DVD
( T V /
S AT )
COA X
DIGITAL IN
T V/
SAT
IN
DVR /
VCR
IN
DVD
IN
R
AUD IO
L
1
MONITOR
OUT
2
R
F M UNBAL75
Ω
AM LOOP
ANTENNA
L
VIDEO
DVR /
VCR
OUT
AUDIO
SUB
WOOFER
OUT
Components with an CONTROL terminals
Mono mini plug
(optional)
AC IN
IN OUT
CONTROL
Plugging in the Receiver
After you have connected all your components, including the speakers, plug the receiver into a wall outlet.
R
FRONT
L
SPEAKERS
CENTER R
SURROUND
L
IN OUT
CONTROL to wall outlet
AC IN
Power cord CAUTION!
Handle the power cord by the plug. Do not pull out the plug by tugging the cord and never touch the power cord when your hands are wet as this could cause a short circuit or electric shock. Do not place the unit or a piece of furniture, etc., on the power cord, or pinch the cord.
Never make a knot in the cord or tie it with other cords. The power cords should be routed such that they are not likely to be stepped on.
A damaged power cord can cause a fire or give you an electrical shock. Check the power cord once in a while. When you find it damaged, ask your nearest PIONEER authorized service center or your dealer for a replacement.
• The power cord is removable from main unit for storage.
19
En
03
Displays & Controls
Front Panel
0 = ~ !
9
$ @ #
1
FRONT INPUT
STANDBY/ON
PHONES
2
VIDEO L AUDIO R
DIGITAL IN
3
INPUT SIGNAL
2
DIGITAL
DTS AUTO
SURROUND MODE
PHONES
/VIRTUAL
2
PRO LOGIC II
ADVANCED
SOUND
MODE
AUDIO/ VIDEO MULTI-CHANNEL RECEIVER
VSX-C100
MASTER
VOLUME
DVD TV/SAT DVR/VCR FM/AM FRONT
DOWN UP
4
1 STANDBY/ON (Main power) button
Pressing this button switches the receiver ON from
STANDBY mode.
RECEIVER button on the remote control also toggles between ON and STANDBY mode.
The receiver uses a small amount of electricity (less than 1W) in STANDBY mode.
2 PHONES jack
Use to connect headphones (this switches the speakers off).
3 FRONT INPUT
You can connect a portable DVD player, video camera, video game system, or whatever equipment you would like to have handy, to the FRONT INPUT
(refer to page 15).
4 INPUT SIGNAL indicators
Indicates the kind of input signal.
2 DIGITAL:
When a 2 DIGITAL source is input this indicator will light.
DTS:
When a DTS source is input this indicator will light.
5 SURROUND MODE indicators
Indicates the SURROUND mode of input signal.
AUTO:
Lights when the AUTO mode is selected. This mode automatically selects which kind of signal is being input and plays back in the appropriate mode.
PHONES/VIRTUAL:
Lights when the VIRTUAL or PHONES SURROUND mode is selected. The VIRTUAL mode simulates surround sound for two speakers (when headphones are not plugged in, see p.33). The PHONES SUR-
ROUND mode simulates surround sound for headphones, when they are plugged in.
2 PRO LOGIC II:
Lights when the 2 PRO LOGIC II mode is selected.
This mode automatically plays back in 2 PRO
LOGIC II (see p.33).
5 6 7 8
ADVANCED:
Lights when an ADVANCED mode is selected. These modes playback emphasizing certain characteristics of the sound (see p.33–34).
6 SOUND MODE
Lights when you have chosen one of the sound modes to be applied to playback (see p.35).
7 Input buttons
Use to select the playback source: the possibilities are
DVD, TV/SAT, DVR/VCR, FM/AM and FRONT.
8 MASTER VOLUME
Use to set the overall listening volume.
DISPLAY
9 TUNER indicators
STEREO: Lights when a stereo FM broadcast is being received in auto stereo mode.
TUNED: Lights when a broadcast is being received.
MONO: Lights when the mono mode is set using
MPX (on the remote control).
RDS: Lights when an RDS broadcast is received.
RF ATT: Lights when the RF ATT is on (see p.36).
0 Digital (DIG) & Analog (ANA) indicators
Light according to the kind of signal, digital or analog, received (see p.44).
96kHz playback indicator
Lights when a 96 kHz source is being played.
= Format indicator
Shows which speakers are currently in use based on the listening mode chosen, the source material and the type of decoding being used (see p.24).
~ SLEEP indicator
Lights when the SLEEP function is set or active (see p.44).
!
OVER indicator
Lights when the analog signal is too powerful, causing possible distortion (see p.31).
20
En
@ EON indicators
EON lights when it has been set. The dot indicator next to it lights when the station you are currently tuned to carries the EON data service.
Displays & Controls
# Volume level indicator
$ Character display
Shows the current input (DVD, TV/SAT, etc.), listening mode, radio frequency, etc.
Rear Panel
1 TV/SAT IN terminals (connect a TV/SAT set top box here, see page 13)
Use these terminals to input a TV/SAT signal (or from another kind of source, if you choose). Make sure to connect to the video terminals and both the analog and optical digital terminals for audio. To be able to play digital surround soundtracks you need to make digital connections. To do this it’s best to use the optical digital terminal here but you can use the coaxial digital terminal if necessary (in this case you need to assign the terminal to the TV/SAT function.
See page 31 in order to do this).
2 MONITOR OUT terminals (connect a TV or monitor here, see pages 12,14)
Use these terminals to output the signal from the above terminals 1 , 5 or 6 and FRONT INPUT.
These are video jacks. MONITOR 2 outputs the same signal as MONITOR 1.
3 ANTENNA terminals
Connect AM or FM antennas here (see page 18).
4 SPEAKERS terminals
Use these terminals to connect speakers to the receiver (see page 16).
5 DVR/VCR IN/OUT terminals (connect a DVR or
VCR here, see page 14–15)
Use the optical digital terminal to connect a DVR out digitally to this receiver. There are also analog terminals to input and output the audio and video signal from a DVR, VCR (or a video camera, etc.).
6 DVD IN terminals (connect a DVD player here, see page 12)
Use these terminals to input the signal from a DVD player. Make sure to connect to the video terminals and both the analog and coaxial digital terminals for audio. To be able to play Dolby Digital and other surround soundtracks you need to make digital connections. To do this it’s best to use the coaxial digital terminal but you can use the OPT 1 digital terminal if necessary (in this case you need to assign the coaxial digital terminal to the TV/SAT function.
See page 31 in order to do this).
7 SUBWOOFER OUT terminals
Use this terminal to connect a powered subwoofer to the receiver (see page 16).
8 CONTROL IN/OUT terminal
You can use this jack to hook up other PIONEER equipment, that bears the CONTROL terminal, so that you can control them all with the remote control for this receiver (see page 19).
9 AC IN (Power In)
Hook up the power cord to this terminal.
21
En
22
En
Displays & Controls
Remote Control
All the buttons on the remote control are explained here. See pages 49 & 50 for details relating to using the remote control with other components (like your DVD player or TV/SAT tuner).
1
2
3
4
5
6
7
8
9
0
RECEIVER
SIGNAL SELECT
SOURCE
SLEEP
DVD TV / SAT FRONT
DIMMER
DVR/ VCR F M / A M
AUTO SURROUND ADVANCED
SOUND
MODE
SETUP TEST TONE CH_SELECT
ROOM
SETUP
ENTER
MUTE
MASTER
VOLUME
TOP MENU DISPLAY T.EDIT
MENU
TUNE
P MENU
ST
ENTER
ST
AUDIO
P
EXIT
EON
TUNE
SUBTITLE
RF ATT
GUIDE
A
SEARCH
B
CLASS
C
MPX
D
D.ACCESS
E
RECEIVER
ENTER
10
TV CONTROL
CHANNEL
INPUT
SELECT
CHANNEL VOLUME
#
$
-
=
~
!
@
%
^
&
1 RECEIVER (Power) button:
This switches between STANDBY mode and power
ON for this receiver.
2 SIGNAL SELECT button (See p.44):
Press SIGNAL SELECT repeatedly to select one of the following:
ANALOG: To select an analog signal.
DIGITAL: To select a digital signal.
AUTO: This is the default. If there are analog and digital signals input, the receiver automatically selects digital. If only analog is input the receiver will select analog.
3 Input/Control Mode Select buttons:
Use to put the receiver/remote control in the input mode stated on the button. The FM/AM button puts the receiver in tuner mode if it was in another mode and switches between the FM and the AM band if the receiver was already in tuner mode.
4 Listening Mode buttons:
AUTO button:
Use this button for direct decoding of the input signal with no added sound effects. The receiver will automatically detect what kind of signal (stereo, multichannel, etc.) is being input and play accordingly.
SURROUND button (see page 34):
Use this button to choose one of the surround listening modes this receiver is equipped with.
ADVANCED button (see page 34):
Use this button to choose one of the advanced listening modes this receiver is equipped with.
SOUND MODE button (see page 35):
Use this button to choose one of the sound modes this receiver is equipped with.
5 System setup buttons:
SETUP button (see page 27):
Use this button to start the receiver setup process which adjusts the settings to your particular system.
TEST TONE button (see page 32):
Use to sound the TEST TONE when setting the volume level of each channel.
CH SELECT button (see page 32, note):
Use to select a speaker when setting the volume level of each channel.
ROOM SETUP button (see page 26):
Use to set the distance from your speakers to your normal listening position.
+/– buttons (see pages 28–32):
Use these buttons when making adjustments to the
SETUP, TEST TONE, or CH.SELECT features.
ENTER button:
Use this button to enter Room Setup commands.
You can also use this button to exit a SETUP mode.
6 Volume buttons:
MASTER VOLUME +/– buttons:
Use to set the overall listening volume.
MUTE button (see page 43):
Use to mute the sound or restore the sound if it has been muted.
7 TOP MENU button:
Use to return to the most basic menu on a DVD player or disc. Also used for some tuner commands.
8 AUDIO button:
Use to switch the audio tracks of a DVD when in
DVD mode or to access the EON function when in tuner mode.
9 Number buttons:
Use to enter track number on discs or radio frequencies.
0 CHANNEL +/– buttons:
Use to select channels on other components such as a DVR or satellite tuner.
LED indicator:
This indicator flashes when a command is sent from the remote control to the receiver. It also flashes at when teaching the receiver preset codes.
= SOURCE (Power) button:
Use this button to turn on and off the power of other components.
~ SLEEP button (see page 44):
Use to put the receiver in sleep mode and select the amount of time before the receiver turns off.
!
DIMMER button (see page 43):
Press to change the display brightness. The
DIMMER button allows you to cycle through the four different brightness strengths for the display.
@ MENU button:
Use to return to the most basic menu on a DVD player or disc. Also used for some tuner commands.
# } ] ’ ‘ & ENTER buttons
Use these arrow buttons when adjusting the tuner or navigating TV or DVD menus. See these respective sections for more information.
$ SUBTITLE button:
Use to switch the subtitles on a DVD player or disc. Also used to turn on RF ATT when in tuner mode.
Displays & Controls
% Component/Tuner/Satellite Tuner/CATV control buttons:
The main function of these buttons ( 3 , 7 , etc.) is to control a component (CD, for example) after you have selected it using the Input/Control
Mode Select buttons. The tuner/satellite tuner controls above these buttons can be accessed after you have selected the corresponding Input/
Control Mode Select buttons (TUNER or SAT, etc.). In this case the buttons marked with letters
(A, etc.) or EXIT will access preset channels or functions, depending on your particular satellite/ cable TV system.
SEARCH button:
Use when searching for stations in RDS mode.
CLASS button (page 37–38):
Switches between the three banks (classes) of radio station presets.
MPX button (page 36):
Switches between stereo and mono reception of
FM broadcasts. If the signal is weak then switching to mono will improve the sound quality. Also acts as a stop button for CDs, tapes, or DVDs.
D. ACCESS button (page 37):
After pressing, you can access a radio station directly using the number buttons.
^ ENTER button (page 49–50):
It can be used to enter commands for TV, CATV and TUNER.
& TV CONTROL buttons:
These controls are for your TV. They are dedicated TV controls and will work no matter what mode the remote control is in. They can, however, be set for different TVs. By default they will control the TV. Thus if you only have one TV, assign it to the TV/SAT button (see page 47).
23
En
04
Basic Playback
Checking the Settings on Your DVD (or other) Player
If you don’t set the following two features correctly you may experience problems with your surround sound (for example: no sound whatsoever; the sound is unidimensional or lacks punch; or other problems).
1 Digital output from your DVD player or other component outputting a digital source
Set the DVD player so the signals below are output from the optical terminal (if you are unsure how to do this check the manual that came with your DVD player). It may or may not be necessary to set the digital output on other components, like a satellite tuner. Check the manual that came with the component.
• Dolby Digital
• DTS
• 96 kHz PCM (2 channel stereo)
2 Checking the soundtrack on your disc
Choose the surround sound signal (for example, Dolby Digital 5.1 ch or Dolby Surround) that you want to hear from the disc. Check the manual that came with your DVD player for more information.
• Depending on your DVD player or source discs you may not be able to output sound from other than digital 2 channel stereo and analog. In this case you need to change the listening mode to SURROUND if you want multichannel surround sound.
Program Format/Speaker Channel Indicators
One very useful feature of this receiver is the Program Format/Speaker Channel Indicators. This indicator looks something like this:
The letters
(Input indicator)
The triangular segments and SW
(Output indicator)
With this indicator you can determine which channels are present in a Dolby Digital or DTS source as well as the speakers that are currently being used. The letters L, C, R, LFE, LS & RS represent the signal being input for each channel respectively, with LFE being the Low Frequency Effects channel which feeds your subwoofer. These letters will only appear if the input is a Dolby Digital or DTS signal.
The triangular segments and SW represent the output from the receiver. The upper segments represent the front left, center, and front right speakers while the bottom segments represent the surround left and surround right channels. SW represents the subwoofer channel. If you have all of these speakers connected and are using either a multichannel signal (for example, Dolby Digital 5.1 ch or Dolby Surround), or a listening mode to get five channels sound, all five of the segments will light. For stereo signals only the front left, center, and front right speakers segments will light.
In some cases, depending on the source and listening mode, the output channels may not light up.
24
En
Basic Playback
Playing a Source
Here are the basic instructions for playing a disc or videotape (or any other source) with your home theater system.
The following pages will tell you about refinements you can make to the sound but the below procedure (with the settings you have already made) should allow you to get enjoyable home theater.
2
3
RECEIVER
SIGNAL SELECT
SOURCE
SLEEP
DVD TV / SAT FRONT
DIMMER
DVR/ VCR F M / A M
AUTO SURROUND ADVANCED
SOUND
MODE
SETUP TEST TONE CH_SELECT
ROOM
SETUP
ENTER
MUTE
MASTER
VOLUME
TOP MENU DISPLAY T.EDIT
MENU
TUNE
P MENU
ST
ENTER
ST
AUDIO
P
EXIT
EON
TUNE
SUBTITLE
RF ATT
GUIDE
A
SEARCH
E
CLASS
C
MPX
D
D.ACCESS
E
ENTER
10
CHANNEL
TV CONTROL
CHANNEL VOLUME
4
7
1 Turn on the power of the playback component (for example a DVD player), your TV and subwoofer (if you have one).
2 Press
RECEIVER
to turn the power on.
3 Select the source (like a DVD player) you want to playback using the individual Input buttons on the remote control.
4 Set the signal select to AUTO (if necessary).
5 Make sure the TV is set to this receiver.
If you’re not sure which input on your TV this receiver is hooked up to confirm the input jack on the back of the TV and consult the manual that came with your TV to figure out the proper setting.
6 Start playback of the component you selected in step 3.
7 Press
MASTER VOLUME (+/–)
to adjust the volume level.
RECEIVER
2
STANDBY/ON button
FRONT INPUT
STANDBY/ON
PHONES
VIDEO L AUDIO R
DIGITAL IN
INPUT SIGNAL
2
DIGITAL
DTS AUTO
SUR
PHON
/VIRTU
• If you want to use analog sources choose analog with the SIGNAL SELECT button (see page 44).
• When you’re using your TV’s internal tuner the TV shouldn’t be set to this receiver (step 5 above).
• For Karaoke make sure the equipment is hooked up with analog connections and choose analog with the
SIGNAL SELECT button (see page 44).
3
Input buttons
7
MASTER VOLUME
SURROUND MODE
PHONES
/VIRTUAL
2
PRO LOGIC II
ADVANCED SOUND
MODE
AUDIO/ VIDEO MULTI-CHANNEL RECEIVER
VSX-C100
MASTER
VOLUME
DVD TV/SAT DVR/VCR FM/AM FRONT
DOWN UP
25
En
05
Fine Tuning Your Surround Sound
Room Setup
This setup establishes the distances from your speakers to your normal listening position. It is important for the receiver to know these distances so it can output proper surround sound. Alternatively, you can make more precise speaker distance settings on page 27-29. You don’t have to do both, however.
There are three choices for speaker distances here. They are marked ‘S’, ‘M’ and ‘L’ but they represent the relationship between how far your front speakers and your surround speakers are from your normal listening position, i.e. the relationship in distance between the speakers and your listening position. ‘S’ should be used when your surround speakers are nearer your main listening position than your front speakers. ‘M’ should be used when all your speakers are equidistant from your main listening position. ‘L’ should be used when your surround speakers are farther from your main listening position than your front speakers.
Follow the instructions below to set the room type.
S
L
(surround speakers closer to listening position)
C R SW
M
(speakers are equidistant to listening position)
L C R SW
L
L
(front speakers are closer to listening position)
C R SW
26
En
LS RS
1 RECEIVER
SIGNAL SELECT
SOURCE
SLEEP
DVD TV / SAT FRONT
DIMMER
DVR/ VCR
F M / A M
AUTO
SURROUND ADVANCED
SOUND
MODE
SETUP
TEST TONE CH_SELECT
ROOM
SETUP
ENTER
MUTE
MASTER
VOLUME
TOP MENU DISPLAY T.EDIT
MENU
P
AUDIO
ST
P
EXIT
EON
TUNE
ENTER
ST
MENU
TUNE
SUBTITLE
RF ATT
GUIDE
A
SEARCH
E
CLASS
C
MPX
D
D.ACCESS
E
2
3
ENTER
1
STANDBY/ON button
FRONT INPUT
STANDBY/ON
PHONES
VIDEO L AUDIO R
DIGITAL IN
INPUT SIGNAL
2
DIGITAL
DTS
LS RS
LS RS
1 Press
RECEIVER
to turn the power on.
2 Press
ROOM SETUP
.
Cycle through the ‘S’, ‘M’, or ‘L’ settings using the ROOM
SETUP button and choose the one that best represents the placement of your speakers around the room.
The setting will blink for five seconds.
3 While the display is blinking press
ENTER
.
The setting is input into the system and the display shows
ENTERED.
• These speaker settings will automatically adjust the distance between your listening position and the speakers as well as the output level from each speaker. It is also possible to select these functions manually. To do so see below. For the distance between the listening position and the speakers see pages 27-29; For the output level of each speaker see page
32.
• The settings made most recently, whether here or manually, on the pages mentioned directly above, will supercede any previous settings.
• The default setting is ‘M’.
Personalizing Your Surround
Sound
This receiver will make the necessary speakers settings automatically so you can use it to get enjoyable surround sound without doing anything, but making more exact settings here will give you finer surround sound.
For better surround sound complete the instructions that follow the speaker settings. Use the first two steps on this page and continue on page 28. In this way you can get maximum performance out of the receiver.
You only need to do these settings once (unless you change the placement of your current speaker system or add new speakers, etc.). The following pages offer a more detailed description of the settings available for each mode. The default setting is also shown on each page.
1
2
RECEIVER
SIGNAL SELECT
SOURCE
SLEEP
DVD TV / SAT FRONT
DIMMER
DVR/ VCR F M / A M
AUTO
SURROUND ADVANCED
SOUND
MODE
SETUP TEST TONE CH_SELECT
ROOM
SETUP
ENTER
MUTE
MASTER
VOLUME
TOP MENU
DISPLAY T.EDIT
MENU
P
ST
TUNE
ENTER
ST
MENU
AUDIO
P
EXIT
EON
TUNE
SUBTITLE
RF ATT
GUIDE
A
SEARCH
E
CLASS
C
MPX
D
D.ACCESS
E
ENTER
10
TV CONTROL
CHANNEL
INPUT
SELECT
CHANNEL VOLUME
RECEIVER
3
Fine Tuning Your Surround Sound
For best results, start with Front speakers setting mode and make your initial adjustments in the order described below.
The current settings are displayed automatically.
• Front speakers setting mode (page 28)
Use to specify the size and configuration of the
FRONT speakers you have connected.
• Center speaker setting mode (page 28)
Use to specify the size and configuration of the
CENTER speaker you have connected.
• Surround speaker setting mode (page 28)
Use to specify the size and configuration of the
SURROUND speakers you have connected.
• Subwoofer setting mode (page 28)
Use to set the subwoofer output and determine at which frequency the bass tones will be sent to the subwoofer (if it is on).
• LFE (Low Frequency Effects) attenuator setting mode (page 29)
Use to lower the level for the LFE channel (a special bass channel) when the LFE level is so high as to distort.
• Front speakers distance setting mode (page 29)
Use to specify the distance from your listening position to your front speaker.
• Center speakers distance setting mode (page 29)
Use to specify the distance from your listening position to your center speaker.
• Surround speakers distance setting mode (page
30)
Use to specify the distance from your listening position to your surround speakers.
• Dynamic range control setting mode (page 30)
Use to compress the dynamic range of a Dolby Digital soundtrack with this feature (for non-Dolby Digital soundtracks use the MIDNIGHT mode for the same effect).
• Dual mono setting (page 30)
Use with soundtracks that have dual mono encoding if you want to isolate one channel to a particular speaker.
• Input attenuator setting (page 31)
Use to reduce the analog input level coming into the receiver when it is so loud as to make it distort.
• Coaxial connection setting (page 31)
Use to tell the receiver (assign) which component is hooked up the other coaxial digital terminal.
3 Press
ENTER
to exit the setting mode.
1 Press
RECEIVER
to turn the power on.
2 Press
SETUP
.
Make the adjustments that match your home setup using the +/– buttons. When finished with one setting continue to cycle through the setting modes using the
SETUP
button and make adjustments in the same way.
The setting mode is automatically exited if no operation is performed within 20 seconds.
27
En
28
En
Fine Tuning Your Surround Sound
Front speakers setting
This settings establishes the size and configuration of the front speakers you have connected more exactly than the automatic setup. Select either Large ( L ) or Small ( S ). This will determine if bass sounds are sent by the receiver to the speakers being set.
Large: If the cone size (diameter) of your speaker(s) is larger than 12 centimeters, set to Large.
Small: If the cone size (diameter) of your speaker(s) is 12 centimeters or smaller, set to Small.
Follow steps 1&2 on page 27 (if necessary).
Use the
+/ –
buttons to choose a speaker setting according to the speakers you hooked up.
Press SETUP to advance to the next receiver setting mode.
Press
ENTER
if you want to exit the setting mode.
Surround speakers setting
This settings establishes the size and configuration of the surround speaker you have connected more exactly than the automatic setup. Select either Large ( L ) or Small ( S ).
This will determine if bass sounds are sent by the receiver to the speaker being set. If no speakers are connected choose “–”.
Large: If the cone size (diameter) of your speaker(s) is larger than 12 centimeters, set to Large.
Small: If the cone size (diameter) of your speaker(s) is 12 centimeters or smaller, set to Small.
None (–): Choose this setting if you have no speaker(s) hooked up to this terminal. Sound coming from this channel in the original source will be down-mixed to one of the active speakers.
Follow steps 1&2 on page 27 (if necessary).
Use the
+/ –
buttons to choose a speaker setting according to the speakers you hooked up.
Press SETUP to advance to the next receiver setting mode.
Press
ENTER
if you want to exit the setting mode.
Center speaker setting
This settings establishes the size and configuration of the center speaker you have connected more exactly than the automatic setup. Select either Large ( L ) or Small ( S ).
This will determine if bass sounds are sent by the receiver to the speaker being set. If no speakers are connected choose “–”.
Large: If the cone size (diameter) of your speaker(s) is larger than 12 centimeters, set to Large.
Small: If the cone size (diameter) of your speaker(s) is 12 centimeters or smaller, set to Small.
None (–): Choose this setting if you have no speaker(s) hooked up to this terminal. Sound coming from this channel in the original source will be down-mixed to one of the active speakers.
Follow steps 1&2 on page 27 (if necessary).
Use the
+/ –
buttons to choose a speaker setting according to the speakers you hooked up.
Press SETUP to advance to the next receiver setting mode.
Press
ENTER
if you want to exit the setting mode.
• If the front speakers are set to Small ( S ) you can’t choose Large ( L ) for the center speaker.
• If the center and surround speakers are set to None (–) the listening modes for all the inputs will automatically go into AUTO mode.
• If the front speakers are set to Small ( S ) you can’t choose Large ( L ) for the surround speakers.
• If the center and surround speakers are set to None (–) the listening modes for all the inputs will automatically go into AUTO mode.
Subwoofer setting
The Subwoofer setting divides the high and low sounds
(frequencies) between the speakers. Since most smaller speakers can’t handle deep bass tones, this setting allows you to send those sounds to the subwoofer instead of the speakers set to Small ( S ) in your system. Choose the point at which you want the frequency routed to the subwoofer.
We recommend setting this to 200 Hz if smaller bookshelf-type speakers are used for your “Small” speakers.
Also, when a subwoofer is used, you have the option of selecting the PLS setting, which adds extra bass.
Follow steps 1&2 on page 27 (if necessary).
Use the
+/ –
buttons to choose subwoofer setting 100 Hz, 150 Hz, 200 Hz, PLS (plus) or – – – (off).
SUBWF 200 Hz
Sends bass frequencies below 200 Hz to the subwoofer.
SUBWF 150 Hz
Sends bass frequencies below 150 Hz to the subwoofer.
SUBWF 100 Hz
Sends bass frequencies below 100 Hz to the subwoofer.
SUBWF PLS
Adds extra bass to the soundtrack.
SUBWF – – –
Select if you didn’t connect a subwoofer.
Press SETUP to advance to the next receiver setting mode.
Press
ENTER
if you want to exit the setting mode.
Fine Tuning Your Surround Sound
Front speakers distance setting
Set the distance from the front speakers to the listening position.
Follow steps 1&2 on page 27 (if necessary).
Use the
+/ –
buttons to choose the distance of the front speakers from the main listening position (within a range from 0.3 m to 9.0 m).
Press SETUP to advance to the next receiver setting mode.
Press
ENTER
if you want to exit the setting mode.
• The Subwoofer setting will appear automatically, depending on whether you have connected a subwoofer or not.
• The default setting is “200 Hz”.
• You can only select PLS when the front speakers are set to Large ( L ).
• If the all the speakers are set to Large ( L ) you can only select 100 kHz, PLS or off (– – –) for the
Subwoofer.
• Setting the front speakers to Small ( S ) means you will use a subwoofer, thus its setting cannot be turned off. In this case make sure you set the subwoofer and choose its cutoff frequency.
• There are some cases where no sound will come from the subwoofer even if it is (this depends on the speaker setting, the listening mode and/or the kind of source material).
• The default setting is “1.8 m”.
• One step equals about 0.3 m.
• If you do the Room Setup (see page 26) after the settings here, those will take precedence.
Center speaker distance setting
Set the distance from the center speakers to the listening position.
Follow steps 1&2 on page 27 (if necessary).
Use the
+/ –
buttons to choose the distance of the center speaker from the main listening position (within a range from 0.3 m to 9.0 m).
Press SETUP to advance to the next receiver setting mode.
Press
ENTER
if you want to exit the setting mode.
LFE attenuator setting
Dolby Digital and DTS audio sources include ultra-low bass tones. Set the LFE attenuator as needed to prevent the ultra-low bass tones from distorting the sound from all the active speakers.
Follow steps 1&2 on page 27 (if necessary).
Use the
+/ –
buttons to choose the attenuation level 0 dB, 10 dB or LFE OFF.
0 dB
No attenuation.
10 dB
LFE volume is reduced.
LFE OFF
LFE channel is off.
Press SETUP to advance to the next receiver setting mode.
Press
ENTER
if you want to exit the setting mode.
• The default setting is “1.5 m”.
• One step equals about 0.3 m.
• When “ CENTER –” is selected in Center speaker setting, the Center speaker distance cannot be set.
• If you do the Room Setup (see page 26) after making the settings here, those will take precedence.
• The default setting is “0 dB”.
29
En
30
En
Fine Tuning Your Surround Sound
Surround speakers distance setting
Set the distance from the surround speakers to the listening position.
Follow steps 1&2 on page 27 (if necessary).
Use the
+/ –
buttons to choose the surround speakers from the main listening position
(within a range from 0.3 m to 9.0 m).
Press SETUP to advance to the next receiver setting mode.
Press
ENTER
if you want to exit the setting mode.
• The default setting is “1.8 m”.
• One step equals about 0.3 m.
• When “ SURR. –” is selected in Surround speakers setting, the Surround speakers distance cannot be set.
• If you do the Room Setup (see page 26) after the settings here, those will take precedence.
Dual mono setting
Dual mono has two different audio channels in it. You can use it to listen to soundtracks that have one language on one channel and a different language on the other.
The dual mono setting can only be used when listening to discs that have dual mono software encoded in them, for example some Dolby Digital discs. As of now these are not that widely used.
The ch1 setting plays channel 1 through your center speaker. If you have selected no Center speaker in the speakers setting (or are in a 2 ch listening mode) then you will hear ch1 out of both front speakers. The ch2 setting plays channel 2 through your center speaker. If you have selected no Center speaker in the speakers setting (or are in a 2 ch listening mode) then you will hear channel 2 out of both front speakers. In the L. c1
R. c2 setting the speakers will play the soundtrack independently of each other. The left front speaker will play channel 1 and the right front speaker will play channel 2.
Follow steps 1&2 on page 27 (if necessary).
Use the
+/ –
buttons to choose the Dual mono setting (ch1, ch2 or L. c1 R. c2).
Press SETUP to advance to the next receiver setting mode.
Press
ENTER
if you want to exit the setting mode.
Dynamic range control setting
Dynamic range is the difference between the loudest and softest sounds in any given signal. The dynamic range control helps you playback sounds so the quieter sounds are audible yet the louder sounds don’t get distorted. It does this by compressing the dynamic range. When watching a movie at low volume, setting this function enables low level sounds to be heard more easily but you won’t be jolted by louder sounds.
Follow steps 1&2 on page 27 (if necessary).
Use the
+/ –
buttons to choose the dynamic range control (OFF, MAX, or MID).
Dynamic range control is operative only when a
Dolby Digital soundtracks with this feature encoded into it is being played back. For other sources use the
MIDNIGHT mode (see page 35) to achieve the same effect.
Press SETUP to advance to the next receiver setting mode.
Press
ENTER
if you want to exit the setting mode.
• The default setting of this feature is “ch1”.
• The default setting is “OFF”.
• When listening at high volume, set to OFF.
• For best results at low volumes, set to “MAX” for maximum dynamic range compression.
• Dynamic range control is expressed as DRC in the display.
Fine Tuning Your Surround Sound
Input attenuator setting
You can set the input signal to be lowered if it is distorting. This is only possible for analog signals, digital signals can’t be attenuated.
Follow steps 1&2 on page 27 (if necessary).
Use the
+/ –
buttons to set the input attenuator ON or OFF.
Press SETUP to advance to the next receiver setting mode.
Press
ENTER
if you want to exit the setting mode.
• The default setting is “OFF”.
• When the OVER indicator light please put the input attenuator ON.
• The Input Attenuator is expressed as IN.ATT in the display.
Coaxial connection setting
(assigning the coaxial terminal)
This receiver has two different ways you can connect your digital video components (like a DVD player, satellite tuner, or DVR). You can connect them with an optical or coaxial cords (see p.11). The easiest way to hook your equipment is using the default settings of this receiver. In this case, use a coaxial cord to connect your
DVD player. If you use the coaxial terminal for your satellite or TV tuner (called TV/SAT on the receiver) you need to assign that component to the remote (that is, tell the remote that you used the coaxial terminal for your TV/SAT). The optical terminals’ default settings will change in accordance with how you assign the coaxial terminal here. See the next heading for more information.
Follow steps 1&2 on page 27 (if necessary).
Use the
+/ –
buttons to choose the component that you hooked up with coaxial cords.
Press SETUP to advance to the next receiver setting mode.
Press
ENTER
if you want to exit the setting mode.
Optical connection default settings
You can connect your digital video components (like a
DVD player, satellite tuner, or DVR) with optical or coaxial cords, as explained directly above and on page
11. However, the optical terminals cannot be assigned, you must follow their default settings in order to match your equipment to the remote control buttons (and display names, etc.) of this receiver. Thus if you followed the default setting for the coaxial terminal and hooked a DVD up to that terminal the optical terminal default settings are:
OPT. 1: TV/SAT
OPT. 2: DVR
If you assigned your TV/SAT (displayed as SAT) to the coaxial terminal (see “Coaxial connection setting” above and “Connecting Your Equipment” page 12–14) then the defaults for the optical terminals will change
(because you cannot have one component assigned to two different places). Thus they become:
OPT. 1: DVD
OPT. 2: DVR
Follow the default settings when hooking up equipment to the optical terminals.
31
En
32
En
Fine Tuning Your Surround Sound
Setting the Volume Level of
Each Channel (adjusting the speaker volume balance)
Use to set the relative volume of each channel as you find necessary.
1
4
(+/
−
button)
RECEIVER
SIGNAL SELECT
SOURCE
SLEEP
DVD TV / SAT FRONT
DIMMER
DVR/ VCR F M / A M
AUTO SURROUND ADVANCED
SOUND
MODE
SETUP TEST TONE CH_SELECT
ROOM
SETUP
ENTER
MUTE
MASTER
VOLUME
TOP MENU DISPLAY T.EDIT
MENU
TUNE
P
MENU
ST ST
ENTER
AUDIO
P
EXIT
EON
TUNE
SUBTITLE
RF ATT
GUIDE
A
SEARCH
E
CLASS
C
MPX
D
D.ACCESS
E
ENTER
10
TV CONTROL
CHANNEL
INPUT
SELECT
CHANNEL VOLUME
3,5
CH SELECT button
2
4 Use the
+
or
–
buttons to adjust speaker levels so that you hear the test tone at the same volume from each speaker when seated in your main listening position.
• If a speaker is deselected in the center, surround speaker or subwoofer setting mode (see page 28) then no test tone will be output for that speaker.
• The channel level range is ± 10 dB.
• Levels can be set for each surround mode.
5 Press
TEST TONE
to turn off the test tone.
• Since the subwoofer transmits an ultra-low frequency its sound may seem quieter than it actually is. Be careful not to turn up your subwoofer too much and check the volume with an actual source.
• The subwoofer volume is best controlled with the volume control on the powered subwoofer.
• The speaker volume can be adjusted without outputting the test tone by pressing CH SELECT and
+/
−
button.
• The default setting is 0 dB for all channels.
• If you have adjusted the channel level using the + button, even if the master volume is all the way up you’ll never actually get a volume level that is 0 dB
(full volume).
RECEIVER
1 Press
RECEIVER
to turn the power on.
2 Press
MASTER VOLUME +
or
–
to adjust the volume to an appropriate level.
3 Press
TEST TONE
to output the test tone.
The test tone is output in the following order.
Front L
(L)
Center
(C)
Front R
(R)
Subwoofer
(SW)
Surround L
(LS)
Surround R
(RS)
The test tone sequence corresponds to the speaker settings.
Playback Modes
Listening Modes
Intrinsic to home theater, surround sound delivers a realistic and powerful soundtrack that recreates the movie theater experience. You may need to experiment with these different modes to see which suit your home system and personal tastes, but in general you should listen to movie sources (like DVDs) in one of the listening modes for multichannel outputs.
AUTO
This mode automatically detects what kind of signal is being input and employs the proper listening mode of the receiver. If you don’t know what kind of signal (stereo, multichannel, etc.) you are using or don’t want to bother with switching listening modes, use this feature. This is the basic home theater decoding mode.
06
SURROUND
These modes are generally used for two channel sound sources though you can use multichannel sources like
Dolby Digital. If you use multichannel sources with these modes you won’t be able to select the first three.
Try the modes with sources that seem to match the description of the mode below and decide if you like the results. What modes you are able to access in any given situation will depend on the source you are using, the surround settings and other receiver factors (for example, you won’t be able to access PHONES SURROUND mode unless you have the headphones plugged). Also, according to the speaker settings you have made and the signal input you may or may not be output from a subwoofer in these modes.
2 PRO LOGIC
This mode gives 4.1 channel surround sound. It is less sensitive to the quality of the source material so it may be useful when PRO LOGIC II MOVIE/MUSIC do not give good results.
2 PRO LOGIC II MOVIE (MOVIE)
This mode gives 5.1 channel surround sound. It is suitable for movies, especially those recorded in Dolby Surround.
The channel separation and movement of surround effects is comparable to Dolby Digital 5.1.
2 PRO LOGIC II MUSIC (MUSIC)
This mode gives 5.1 channel surround sound and is suitable for music. The surround effect is more enveloping than
PRO LOGIC II MOVIE.
VIRTUAL (TRUSURROUND VIRTUAL)
This mode imitates surround sound with two speakers. The sound will only be heard from two speakers in this mode but the feeling of an all-encompassing surround sound is reproduced.
PHONES SURROUND
When listening with headphones the above mode becomes PHONES SURROUND. Here the effect of overall surround sound is reproduced for headphone listening.
STEREO
Use this mode to listen to conventional stereo sources and retain a stereo sound. Even if a multichannel source is input when you are using this listening mode, you will only hear two channel sound.
ADVANCED
These modes are used to decode all sound sources but each mode emphasizes certain characteristics of the sound. Experiment with the modes and different sound sources to get an effect that suits you. You cannot choose ADVANCED modes when inputting 96 kHz signals.
MOVIE
This mode simulates the relaxed environment of a medium size movie theater, and is suitable for watching drama.
MUSIC
This mode simulates the acoustics of a large concert hall and is suitable for music or musical sources.
33
En
Playback Modes
TV SURROUND
This mode produces surround sound even for mono or stereo TV sources. It is useful for old movies. A mono TV signal will be able to approximate the effect of overall surround sound.
GAME
Use this mode when playing a video game. It works especially well with sound moving from left to right in such software as racing games, shooting games, and those kind of games with movement in them.
VIRTUAL Surround Back (VIRTL SB)
This mode is especially designed to simulate surround back channels for sources that don’t have them. It emulates the effect of surround back speakers in your listening space.
EXPANDED
This mode is especially designed to give sound depth to Dolby Surround sources. The overall effect expands the sound, giving a dynamic and broad sound to these sources while allowing a faithful reproduction of five speaker sound.
5-CH STEREO (5 STEREO)
This mode is especially designed to give sound depth to Stereo sources. The overall effect builds a dynamic and broad sound space, allowing a reproduction with five speakers.
34
En
Selecting a Listening Mode
Choose a listening mode that suits the soundtrack you are listening to or achieves the effect you want, as explained on the previous page. It will probably be necessary for you to experiment with different modes until you find ones which suit your tastes.
1 Press
AUTO, SURROUND
or
ADVANCED
.
RECEIVER
SIGNAL SELECT
SOURCE
SLEEP
DVD TV / SAT FRONT
DIMMER
DVR/ VCR F M / A M
AUTO SURROUND ADVANCED
SOUND
MODE
SETUP TEST TONE CH_SELECT
ROOM
SETUP
ENTER
MUTE
MASTER
VOLUME
TOP MENU DISPLAY T.EDIT
MENU
P
AUDIO
ST
P
EXIT
EON
TUNE
ENTER
ST
MENU
TUNE
SUBTITLE
RF ATT
GUIDE
A
SEARCH
E
CLASS
C
MPX
D
D.ACCESS
E
ENTER
10
TV CONTROL
CHANNEL
INPUT
SELECT
CHANNEL VOLUME
RECEIVER
1-2
2 If you choose one of the latter two, cycle through the modes using the
SURROUND
or the
ADVANCED
button and select the one suits the soundtrack you’re listening to.
Refer to page 33 for more details about each listening mode.
• The default setting is AUTO. With headphones the default setting is STEREO.
• You can only select the STEREO or PHONES SUR-
ROUND mode when headphones are plugged into the headphone jack.
• The listening mode you choose with headphones is fully independent of the listening mode with speakers.
• If you disconnect the headphones while in PHONES
SURROUND mode the receiver will return to the listening mode it was in before you selected PHONES
SURROUND.
• When inputting a 96 kHz PCM signal you can only use
STEREO listening modes.
• If you are in a different mode than STEREO and then input a 96 kHz PCM signal the receiver will automatically switch to AUTO.
• Each playback component can be set independently and retains its sound mode when another component is being used.
• If you did not connect center and surround speakers you can only choose VIRTUAL or STEREO in SURROUND mode.
Playback Modes
Sound Modes
The Sound Modes allow you to add certain sound elements when playing all kinds of sources (two-channel/stereo sources, Dolby Surround sources, Dolby Digital or DTS sources). They can be used in conjunction with the listening modes explained on the previous page.
NATURAL
This mode flattens the total frequency output to make it match the characteristics of the small speakers. When playing a multichannel source using the small speakers this setting corrects the frequency to achieve better theaterlike surround sound.
MIDNIGHT
This mode makes the softer sounds more audible and the louder sounds a bit softer so you can hear the entire soundtrack, especially quiet sounds and dialog, with a good surround sound feeling when listening at low volumes.
MANNER
This mode reduces the bass and treble in the signal. It is best used when you feel sounds are too harsh or sharp and would like to smooth them out.
BRIGHT
This mode is used for 2ch Stereo, and is only audible from the front speakers. It flattens the total frequency output to make it match the characteristics of the front speakers. When playing two channel sources the bass trim often becomes muddy and this mode offers clear, true sound in low and high frequencies.
S.BASS
This mode increases the bass in the signal and puts the beat of the music or soundtrack in the forefront.
OFF
No sound mode is applied.
Selecting a Sound Mode
The receiver has three tone effect types that you can add to the Listening mode you are using.
RECEIVER
SIGNAL SELECT
SOURCE
SLEEP
DVD TV / SAT FRONT
DIMMER
DVR/ VCR F M / A M
AUTO
SURROUND ADVANCED
SOUND
MODE
SETUP TEST TONE CH_SELECT
ROOM
SETUP
ENTER
MUTE
TOP MENU DISPLAY
TUNE
P
ST
T.EDIT
MENU
ENTER
ST
MENU
AUDIO
P
EON
TUNE
SUBTITLE
RF ATT
GUIDE
1-2
1 Press
SOUND MODE
.
2 Cycle through the different possibilities using the
SOUND MODE
button and select the one you want.
Refer to above for more details about each sound mode.
• The default setting is NATURAL.
• Each playback component can be set independently and retains its sound mode when another component is being used.
• When you choose VIRTUAL mode (page 33) you can’t select a Sound mode.
• When inputting a 96 kHz PCM signal you can’t select a
Sound mode.
35
En
07
Using the Tuner
Finding a Station
The following steps show you how to tune in to FM and
AM radio broadcasts using the automatic (search) and manual (step) tuning functions. If you already know the exact frequency of the station you want to listen to, see
“Tuning Directly to a Station” on page 37. Once you are tuned to a station you can memorize the frequency for recall later—see “Memorizing Stations” on page 37 for more on how to do this.
Automatic tuning
To search for stations in the currently selected band, press and hold either the TUNE + or TUNE – buttons for about a second. The receiver will start searching for the next station, stopping when it has found one.
Repeat this step to search for other stations.
Manual tuning
To change the frequency one step at a time, press the
TUNE + or TUNE – buttons.
High speed tuning
Press and hold the TUNE + or TUNE
−
buttons for high speed tuning, releasing the button once the desired frequency is reached.
1,2
RECEIVER
SIGNAL SELECT
SOURCE
SLEEP
DVD TV / SAT FRONT
DIMMER
DVR/ VCR
F M / A M
AUTO
SURROUND ADVANCED
SOUND
MODE
SETUP
TEST TONE CH_SELECT
ROOM
SETUP
ENTER
MUTE
MASTER
VOLUME
TOP MENU
DISPLAY
T.EDIT
MENU
P
AUDIO
ST
P
EXIT
EON
TUNE
ENTER
ST
MENU
TUNE
SUBTITLE
RF ATT
GUIDE
A
SEARCH
E
CLASS
C
MPX
D
D.ACCESS
E
ENTER
10
TV CONTROL
CHANNEL
INPUT
SELECT
CHANNEL VOLUME
3
RF ATT
MPX
MPX mode
If there is interference or noise during a FM radio broadcast, or the radio reception is weak, press the MPX button to switch the receiver into mono reception mode.
This should improve the sound quality and allow you to enjoy the broadcast.
RF ATT mode
If the radio signal is too strong and/or the sound is distorting press the RF ATT button to attenuate (lower) the radio signal input and reduce the distortion (for FM stations only).
RECEIVER
1 Press the
FM/AM
button on the remote control to put it in tuner mode.
2 Press the
FM/AM
button again to change the band (FM or AM), if necessary.
Each press switches the band between FM and AM.
3 Tune to a station using the
TUNE +
or
TUNE
buttons.
36
En
Using the Tuner
Tuning Directly to a Station
Sometimes, you'll already know the frequency of the station you want to listen to. In this case, you can simply enter the frequency directly using the number buttons on the remote control.
Memorizing Stations
If you often listen to a particular radio station, it's convenient to have the receiver store the frequency for easy recall whenever you want to listen to that station.
This saves the effort of manually tuning in each time.
The receiver can memorize up to 30 stations, stored in three banks, or classes, (A, B and C) of 10 stations each.
When memorizing FM frequencies, the receiver also stores the MPX setting (auto stereo or mono, see page
36) and the RF ATT setting (see p.36).
1
RECEIVER
SIGNAL SELECT
SOURCE
SLEEP
DVD TV / SAT FRONT
DIMMER
DVR/ VCR F M / A M
AUTO SURROUND ADVANCED
SOUND
MODE
SETUP TEST TONE CH_SELECT
ROOM
SETUP
ENTER
MUTE
MASTER
VOLUME
TOP MENU DISPLAY T.EDIT
MENU
P
AUDIO
ST
P
EXIT
EON
TUNE
ENTER
ST
MENU
TUNE
SUBTITLE
RF ATT
GUIDE
A
SEARCH
E
CLASS
C
MPX
D
D.ACCESS
E 3
5
3
MUTE
MASTER
VOLUME
TOP MENU DISPLAY T.EDIT
MENU
P
AUDIO
ST
P
EXIT
EON
TUNE
ENTER
ST
MENU
TUNE
SUBTITLE
RF ATT
GUIDE
A
SEARCH
E
CLASS
C
MPX
D
D.ACCESS
E
ENTER
10
2
4
ENTER
10
TV CONTROL
CHANNEL
INPUT
SELECT
CHANNEL VOLUME
4
TV CONTROL
CHANNEL
INPUT
SELECT
CHANNEL VOLUME
RECEIVER
RECEIVER
1 Press the
FM/AM
button on the remote control to put it in tuner mode.
2 Press the
FM/AM
button again to change the band (FM or AM), if necessary.
Each press switches the band between FM and AM.
3 Press
D.ACCESS
(Direct access).
4 Use the number buttons to enter the frequency of the radio station.
Example: To tune to 106.00 (FM), press 1 – 0 – 6 – 0
– 0
• If you make a mistake while inputting the frequency, press the D.ACCESS button twice to cancel the frequency and start again.
1 Tune to a station you want to memorize.
See “Finding a Station” on page 36 and “Tuning
Directly to a Station” on this page for more detail on how to do this.
2 Press
T.EDIT
.
The display shows a blinking memory class.
3 Press
CLASS
to select one of the three classes.
Repeatedly pressing this button cycles through the three available classes, A, B and C.
4 Press the
ST +
or
ST –
buttons (or the number buttons) to select the station memory number you want.
Pressing these buttons repeatedly cycles through the
10 available station memories in each class.
After choosing the location you want, the preset class and number blink.
5 Press
ENTER
while the display is blinking to input your choice.
6 Repeat steps 1 to 4 to memorize up to 30 stations.
37
En
38
En
Using the Tuner
Naming Memorized Stations
You can input a name of up to four characters for each preset station in the receiver’s memory (see the previous page). This name can be anything you choose. For example, you could input "BBC1" for that station and when you listen to it the name, rather than the frequency number, will appear on your display.
1
SLEEP
DVD TV / SAT FRONT
DIMMER
DVR/ VCR F M / A M
AUTO SURROUND ADVANCED
SOUND
MODE
SETUP TEST TONE CH_SELECT
ROOM
SETUP
ENTER
MUTE
8 Press
ENTER
when you have got the characters you want to enter.
9 Repeat steps 2 to 6 to memorize up to 30 preset broadcast station names.
To erase or change the station name
Perform the procedures of “Naming Memorized Stations” and enter four spaces to erase the memorized station name.
When you want to change a memorized station name, input the new station name using the same procedure.
TOP MENU DISPLAY
TUNE
P
ST
T.EDIT
MENU
ENTER
ST
MENU
AUDIO
P
EXIT
EON
TUNE
SUBTITLE
RF ATT
GUIDE
A
SEARCH
E
CLASS
C
MPX
D
D.ACCESS
E
4
3,5,6,8
Recalling Memorized Stations
Having memorized up to 30 stations (see the previous explanation for how to do this), preset stations can be easily recalled.
2
1 Press the
FM/AM
button on the remote control.
2 Press
CLASS
repeatedly to select the class.
Repeatedly pressing this button cycles through the three available classes, A, B and C.
3 Press
ST +
or
ST –
to select the FM preset channel.
4 Press
T.EDIT
twice to select the station name mode.
1
RECEIVER
SIGNAL SELECT
SOURCE
SLEEP
DVD
TV / SAT
FRONT
DIMMER
DVR/ VCR F M / A M
AUTO SURROUND ADVANCED
SOUND
MODE
SETUP TEST TONE CH_SELECT
ROOM
SETUP
ENTER
MUTE
MASTER
VOLUME
TOP MENU DISPLAY T.EDIT
MENU
P
AUDIO
ST
P
EXIT
EON
TUNE
ENTER
ST
MENU
TUNE
SUBTITLE
RF ATT
GUIDE
A
SEARCH
E
CLASS
C
MPX
D
D.ACCESS
E
3
2
ENTER
5 Press
]
(
ST +
) or
}
(
ST –
) to choose the first character.
Scroll through the letters, numbers and symbols you can input. Stop on the one you want.
6 Press
ENTER
to input the first of the four characters.
That character lights steadily in the display and the cursor automatically moves to the next space.
7 Enter up to three more characters in the same way.
1 Press the
FM/AM
button on the remote control.
2 Press
CLASS
to select the class in which the station is stored.
Repeatedly pressing this button cycles through the three available classes, A, B and C.
3 Use the
ST +
or
ST –
buttons (or the number buttons) to select the station memory in which the station is stored.
Alternatively, recall the station memory using the number buttons on the remote control.
Any time you want to exit the process you can press the T.EDIT button.
• If the receiver is left disconnected from the AC power outlet or the power is turned off for more than one month, the station memories will be lost and will have to be reprogrammed.
Using the Tuner
An Introduction to RDS
Radio Data System, or RDS as it’s usually known, is a system used by FM radio stations to provide listeners with various kinds of information—the name of the station and the kind of show they’re broadcasting, for example. This information shows up as text on the display, and you can switch between the kind of information shown. Although you don’t get RDS information from all FM radio stations, you do with most.
Probably the best feature of RDS is that you can search automatically by type of program. So, if you felt like listening to jazz, you could search for a station that’s broadcasting a show with the program type, "JAZZ."
There are around 30 such program types, including various genres of music, news, sport, talk shows, financial information, and so on.
The receiver lets you display three different kinds of RDS information: “Radio Text”, “Program Service Name”, and
“Program Type”.
“Radio Text” ( RT ) is messages sent by the radio station.
These can be anything the broadcaster chooses—a talk radio station might give out it telephone number as RT, for example.
“Program Service Name” ( PS ) is the name of the radio station.
“Program Type” ( PTY ) indicates the kind of program currently being broadcast.
The receiver can search for and display the following program types:
NEWS
AFFAIRS
INFO
SPORT
News
Current affairs
General information
Sport
EDUCATE Educational material
DRAMA Radio plays or serials
CULTURE National or regional culture, theatre, etc.
SCIENCE Science and technology
VARIED Usually talk-based material, such as quiz
POP M
ROCK M
M.O.R. M shows or interviews.
Pop music
Rock music
“Middle of the road” music also called soft rock
LIGHT M ‘Light’ classical music
CLASSICS ‘Serious’ classical music
OTHER M Other music not fitting any of the above categories
WEATHER Weather
FINANCE Stock market reports, commerce, trading, etc.
CHILDREN Programs for children
SOCIAL A Social affairs
RELIGION Programs concerning religion
PHONE IN Public expressing their views by phone
TRAVEL Holiday-type travel rather than traffic announcements
LEISURE
JAZZ
Leisure interests and hobbies
Jazz
COUNTRY Country music
NATION M Popular music in a language other than
OLDIES
FOLK M
English
Popular music from the ’50s and ’60s
Folk music
DOCUMENT Documentaries
In addition, there are two other program types, ALARM, and NO TYPE. ALARM used for exceptional emergency announcements. You can’t search for this, but the tuner will switch automatically to this RDS broadcast signal.
NO TYPE appears when a type cannot be found.
Using the RDS display
To display the different types of RDS information available (RT, PS and PTY as explained above), press FM/
AM on the remote control and use the DISPLAY button to cycle through the types of RDS information.
Each press changes the display as follows:
RT PS
Frequency
PTY
• In the RT mode, if any noise is picked up while displaying the RT scroll, some characters may be displayed incorrectly temporarily.
• In the RT, when no RT data is transmitted from the broadcast station, NO RADIO TEXT DATA is displayed once and after that the PS data is displayed. If you have entered a name for that station it will be displayed.
• In the PTY mode, there are cases where NO DATA is displayed. In this case the tuner will automatically switch to the PS mode after a few seconds.
• If reception conditions are strong but the RDS data is displayed incorrectly, press RF ATT.
39
En
40
En
Using the Tuner
Searching for RDS Programs
One of the most useful features of RDS is the ability to search for a particular kind of radio program. You can search for any of the program types listed on the previous page —these cover all kinds of music, as well as news, weather forecasts, sports programs, and a variety of others.
When the tuner finds a program type you searched for, the frequency display will blink for about 5 seconds and then the display will show FINISH briefly.
1
4
RECEIVER
SIGNAL SELECT
SOURCE
SLEEP
DVD TV / SAT FRONT
DIMMER
DVR/ VCR F M / A M
AUTO SURROUND ADVANCED
SOUND
MODE
SETUP TEST TONE CH_SELECT
ROOM
SETUP
ENTER
MUTE
TOP MENU DISPLAY
TUNE
P
ST
T.EDIT
MENU
ENTER
ST
MENU
AUDIO
P
EXIT
EON
TUNE
SUBTITLE
RF ATT
GUIDE
A
SEARCH
E
CLASS
C
MPX
D
D.ACCESS
E
3
2
1 Press the
FM/AM
button to put the receiver in tuner mode. Press again to select the FM band (if necessary).
RDS is only broadcast on FM.
2 To select the PTY search mode press the
SEARCH
button.
If NO PTY is displayed it means the tuner couldn’t find that program type at the time of the search.
• This function searches RDS stations preset in the 30station memory. If this function is set when no stations have been preset, NO PTY will be displayed.
If the desired PTY could not be found amongst the
RDS stations in memory, the same display appears.
3 Use the
]
(
ST +
) or
}
(
ST –
) buttons to select the program type you want to hear.
4 Press
ENTER
to search for the program type.
The tuner searches through the FM stations stored in the station memories.
If the tuner finds a matching program type, the tuner plays 5 seconds of the station. To listen to that station, press the ENTER button. (The tuner stops searching.)
If you don’t press the ENTER button during the above mentioned 5 seconds, the tuner resumes the search.
Using the Tuner
An Introduction to EON
EON (Enhanced Other Network information)
EON is a function that allows you to set the receiver to switch to a frequency automatically when a program featuring traffic information or news is being broadcast. It cannot be used in areas that EON information is not transmitted and when FM broadcast stations do not transmit PTY data. When the broadcast ends, the tuner returns to the original frequency or function.
There are two types of EON you can set the tuner to:
1) TA (Traffic Announcement)
This mode will set the tuner to pick up traffic information when it is broadcast.
2) NEWS
This mode will set the tuner to pick up news when it is broadcast.
Setting EON allows automated reception of TA/NEWS broadcasts
When EON is turned on, the receiver will automatically jump to those EON-linked broadcasts. Even if a receiver function other than the tuner is being used, the receiver function will switch to the FM station automatically when an
EON-linked Traffic Information or News program begins. When the program ends, the original function will be restored. The EON function will not operate, however, when the tuner is on AM.
The Receiver’s Internal Program Identification Function
PI (Program Identification)
This is an identifying marker the tuner automatically attaches to stations stored in your preset memory classes (see p.37). The marker distinguishes between stations which transmit RDS data and those that don’t, so that the receiver knows which stations to look at when searching for RDS or EON transmissions. The code is not displayed on the receiver and you don’t need to do anything in regards to setting the PI codes.
PI code registration and erasure
The receiver will automatically register a PI code for any station you input into the memory classes (see p.37) which can receive RDS or EON data. If you want to have a station preset in your memory banks but DON’T want the receiver to search this station for RDS information you can erase the PI code and then the receiver will ignore this station when searching for RDS transmissions.
To erase PI codes, follow this procedure:
1. When tuned to the station whose PI code you want to erase press the EON button for two seconds or more.
ERASE PI will be displayed.
2. Press the ENTER button within 5 seconds.
41
En
42
En
Using the Tuner
Using EON
1
3
RECEIVER
SIGNAL SELECT
SOURCE
SLEEP
DVD TV / SAT FRONT
DIMMER
DVR/ VCR F M / A M
AUTO SURROUND ADVANCED
SOUND
MODE
SETUP TEST TONE CH_SELECT
ROOM
SETUP
ENTER
MUTE
MASTER
VOLUME
TOP MENU DISPLAY T.EDIT
MENU
P
AUDIO
ST
P
EXIT
EON
TUNE
ENTER
ST
MENU
TUNE
SUBTITLE
RF ATT
GUIDE
A
SEARCH
E
CLASS
C
MPX
D
D.ACCESS
E
2
1 Press the
FM/AM
button to put the receiver in FM tuner mode.
2 Tune into an FM station (see p. 36).
When an FM station is broadcasting a news of traffic information program, the dot indicator ( ÷ ) lights in the display to inform you that the currently tuned station carries the EON data service.
3 Press the
EON
button to select the EON mode.
There are two EON modes: EON TA and EON
NEWS. EON TA will automatically search for traffic reports and EON NEWS will automatically search for news reports among your preset stations.
Each press changes the display as follows:
EON TA EON NEWS
OFF
4 EON mode has been set. If the receiver finds such information in the EON-linked broadcast, it will automatically jump to it and the
EON indicator will blink while receiving the broadcast.
The receiver is set to receive EON information even when it is not in tuner mode. If such information is found the receiver will automatically switch into tuner mode to pick up the EON broadcast. When the program ends the receiver will return to the original mode.
• The EON mode is canceled if you switch to AM reception while setting EON. Start once again after you return to FM reception.
• Simultaneous requests for Traffic Information (TA) and News programs is not possible.
• When EON is turned on and a function other than the tuner is selected, the function will switch to the
FM station automatically when Traffic Information or
News begins. When the program ends, the original function will be restored.
• You cannot operate the T.EDIT and SEARCH buttons while the EON indicator in the display lights.
• Functions cannot be changed while the EON indicator in the display blinks (while receiving EON broadcast). If you want to change to a source other than tuner, press the EON button and turn the EON reception off.
• When EON has been set the EON indicator lights.
During reception of news or traffic information broadcast the EON indicator blinks.
Using Other Functions
Muting the Sound
Use this feature to mute the volume.
1
RECEIVER
SIGNAL SELECT
SOURCE
SLEEP
DVD TV / SAT FRONT
DIMMER
DVR/ VCR F M / A M
AUTO
SURROUND ADVANCED
SOUND
MODE
SETUP TEST TONE CH_SELECT
ROOM
SETUP
ENTER
MUTE
MASTER
VOLUME
TOP MENU
DISPLAY T.EDIT
MENU
TUNE
P MENU
1 Press the
MUTE
button on the remote control.
No sound will be audible until the MUTE button is pressed again to cancel the muting. Alternatively, you can press the MASTER VOLUME +/
−
buttons to cancel the muting.
Changing the Display
Brightness (DIMMER button)
The display on the receiver has four brightness settings.
Use the instructions below to adjust the brightness of the display.
RECEIVER
SIGNAL SELECT
SOURCE
SLEEP
DVD TV / SAT FRONT
DIMMER
DVR/ VCR
F M / A M
AUTO
SURROUND ADVANCED
SOUND
MODE
SETUP TEST TONE CH_SELECT
ROOM
SETUP
ENTER
MUTE
MASTER
VOLUME
TOP MENU
DISPLAY T.EDIT
MENU
TUNE
P MENU
ST ST
ENTER
AUDIO
P
EXIT
EON
TUNE
SUBTITLE
RF ATT
GUIDE
A
SEARCH
E
CLASS
C
MPX
D
D.ACCESS
E
ENTER
10
1
Using the Headphones
The headphone features are explained here.
TV CONTROL
CHANNEL
INPUT
SELECT
CHANNEL VOLUME
RECEIVER
FRONT INPUT
PHONES
STANDBY/ON
VIDEO L AUDIO R
DIGITAL IN
1 Use the
DIMMER
button to cycle through the different display brightness settings.
There are four brightness settings, including display off.
PHONES jack
Plug headphones into the PHONES jack on the front of the receiver.
No sound will be audible from the speakers when headphones are plugged in.
• In the off mode all the lights in the display are off except for the master volume indicator, which appears very dimly.
• If you operate the receiver when the display is in the off or dimmed modes the display will light for about two seconds and then go off again.
• When using the headphones you can only select
STEREO or PHONES SURROUND listening modes.
08
43
En
44
En
Using Other Functions
Input Signal Select
This button selects the type of input signal, ANALOG,
DIGITAL or AUTO, sent to the receiver. You need to take special care to switch to the appropriate input when necessary. For example, the switch would have to be on
DIGITAL to hear Dolby Digital or DTS surround sound material but it would have to be on analog to record from the ANALOG out jacks on the receiver. The default setting is AUTO which chooses digital over analog when both are available but goes with whatever is available if it is the only choice.
1
RECEIVER
SIGNAL SELECT
SOURCE
SLEEP
DVD TV / SAT FRONT
DIMMER
DVR/ VCR F M / A M
AUTO SURROUND ADVANCED
SOUND
MODE
SETUP TEST TONE CH_SELECT
ROOM
SETUP
ENTER
MUTE
MASTER
VOLUME
1 Use the
SLEEP
button to cycle through the three sleep time lengths (90 min., 60 min., and 30 min.) and set the sleep timer.
SLEEP indicator
• When the SLEEP timer has been set, or is active, a dot indicator will appear in the display (to the left of the volume indicator).
• Press the SLEEP button once to view how much time is left on the timer before shutdown. Each press after that will cycle through the possible SLEEP time lengths.
1 Use the
SIGNAL SELECT
button to cycle through the three input modes.
Resetting the System
Use this feature to reset the system to its factory default settings.
SEL. AUTO
SEL. DIG
SEL. ANA
AUDIO/ VIDEO MULTI-CHANNEL RECEIVER
VSX-C100
MASTER
VOLUME
DVD TV/SAT DVR/VCR FM/AM FRONT
URROUND MODE
NES
TUAL
2
PRO LOGIC II
ADVANCED SOUND
MODE
DOWN UP
• If there are no digital inputs (see p.12–15), the
SIGNAL SELECT will default to AUTO.
• Set the SIGNAL SELECT to ANALOG if you want to use the receiver for karaoke.
1 1
1 Press the
TV/SAT
button and the
FRONT
button at the same time for five seconds to return all of the settings to their default mode.
The SLEEP Function
Use this function to listen to the receiver and have it turn off at a specified time without you having to do anything.
As is clear from the title this function is useful for drifting off to sleep while listening to music.
• If the receiver is disconnected from a power source for more than a month, or the main power is turned off, it will reset to the default settings.
• The above reset doesn’t affect the presets that you have programmed into the remote control (see page
46-47).
• The receiver resets to STANDBY.
RECEIVER
SIGNAL SELECT
SOURCE
SLEEP
DVD TV / SAT FRONT
DIMMER
DVR/ VCR F M / A M
AUTO SURROUND ADVANCED
SOUND
MODE
SETUP TEST TONE CH_SELECT
ROOM
SETUP
ENTER
MUTE
1
Setting Type
Input
MASTER VOLUME
Listening mode
Listening mode (with headphones)
Sound mode
Input signal select
Speakers (Front, Center, Surround) setting
Subwoofer setting
LFE attenuator
Front speakers distance
Center speakers distance
Surround speakers distance
Dynamic range control
Dual mono
Input attenuator
Coaxial connect setting
Setting the volume level of each channel
Using Other Functions
Default Settings for the Receiver
All the settings that return to their defaults when you reset the system are listed here (see the previous page “Resetting the System”).
Default Settings
DVD
– – – dB (no sound)
AUTO (all inputs)
STEREO (all inputs)
NATURAL
AUTO automatically sensed
200 kHz
0 dB
1.8 m
1.5 m
1.8 m
OFF ch1
OFF
DVD (OPT1 TV/SAT)
Front “0 dB”, Center “0 dB”,
Surround “0 dB”, Subwoofer “0 dB”
Page
page 21 page 20 page 33 page 33 page 35 page 44 page 28 page 28 page 29 page 29 page 29 page 29 page 30 page 30 page 30 page 31 page 32
• The default settings for the remote control to control other components are listed on page 43.
45
En
09
Controlling the Rest of Your System
Changing the Remote Control Mode
The remote control that comes with this receiver is very flexible and can be switched from controlling this receiver to controlling other components, even components not made by Pioneer. You can set up the remote to control so it will be able to control everything in your system and thus you’ll only need to use this remote when operating your home theater system.
The settings to control other components on this remote control are for Pioneer equipment but you can include most other brand makers. You do this by inputting preset codes that have been decided for each brand maker into the remote (see the next page). After these codes are input you’ll be able to operate the equipment.
For this remote, when you press an input button (like DVD) it also changes the remote control from controlling the receiver to controlling DVD functions as well as switching the input to the receiver.
Switching the Operation Mode of the Remote
Press the button for the piece of equipment you want to control with this remote (for example DVD). Since the buttons have different functions when operating different equipment pages 46 &47 will give you detailed information on what each button does in each operation mode.
Buttons for controlling other components
Receiver Control buttons
Input/Control
Mode Select buttons
Press the button of the component you want to use this remote to operate. This will both change the input into the receiver and the remote control operation mode.
The factory settings for all Input/Control Mode Select buttons are explained here. All the settiings are all for Pioneer components but you can change this.
DVD: DVD player
TV/SAT: TV
DVR/VCR: DVD recorder
FM/AM: the built-in radio tuner
FRONT: VCR
TV: TV
(For a detailed chart of the factory settings see “Clearing the Preset
Codes” on page 48)
Buttons for controlling other components
Dedicated TV
CONTROL buttons
46
En
• The TV CONTROL buttons are dedicated to controlling the TV. They will always control the TV no matter what operation mode the remote is in. Of course, you need to input the preset code for your TV (if it is not Pioneermade) in order to control it with this remote. If, however, you input the code for a similar component (like a satellite TV tuner) for a different button (like the TV/SAT button) the TV CONTROL buttons may take on the controls of that component when in that mode (i.e. when you press the TV/SAT button the TV CONTROL buttons might control your satellite TV tuner, not your TV).
Controlling the Rest of Your System
Recalling Preset Codes
The following steps show you how to recall preset codes for each Input/Control Mode Select button or the TV
CONTROL buttons. In the former case, once the preset code is assigned, pressing the button will automatically set the remote to operate the respective component.
• Refer to “Preset Code List” on pages 51–53 for the components and manufacturers available. You should have no problem controlling a component if you find the manufacturer in this list, but you can only set these codes for the button that is assigned to that component. So, for example, the TV codes can only be set to the TV/SAT button.
Please note that there are cases where only certain functions may be controllable after assigning the proper preset code, or the codes for the manufacturer in the list will not work for the model that you are using.
• Refer to “Controlling the Rest of Your System” on pages 49 & 50 for detailed explanations on how to operate your other components.
1 While pressing the
ENTER
button press the
Input/Control Mode Select
button you want to preset. For the
TV CONTROL
buttons press the
TV CONTROL
(Power) button while pressing the
ENTER
button.
The LED lights.
To cancel the preset mode at any time
Press ENTER .
The remote control will also return to the previous mode after thirty seconds of inactivity.
2 Use the number buttons to enter the 3 digit setup code (see pages 51–53 for “Preset Code
List”).
The LED turns off.
After a code has been input the power of the component being input will turn on or off.
The remote will return to the previous mode after thirty seconds of inactivity.
The power of the component being input will only turn on or off if that component is able to be turned on directly by remote control.
3 Repeat process to assign preset codes for as many components as you want.
LED
1
1
TV CONTROL
(power)
RECEIVER
SIGNAL SELECT
SOURCE
SLEEP
DVD TV / SAT FRONT
DIMMER
DVR/ VCR F M / A M
AUTO SURROUND ADVANCED
SOUND
MODE
SETUP TEST TONE CH_SELECT
ROOM
SETUP
ENTER
MUTE
TOP MENU DISPLAY
TUNE
P
ST
T.EDIT
MENU
ENTER
ST
MENU
AUDIO
P
EXIT
EON
TUNE
SUBTITLE
RF ATT
GUIDE
A
SEARCH
E
CLASS
C
MPX
D
D.ACCESS
E
ENTER
10
TV CONTROL
CHANNEL
INPUT
SELECT
CHANNEL VOLUME
1
2
• You can only input a code for the component type written on each Input/Control Mode Select button.
• Even if you don’t input a preset code for the TV (TV/
SAT Input/Control Mode Select button) you will be able to control your TV using the dedicated TV
CONTROL on the remote.
CAUTION:
• You may not be able to use a particular code even if it is listed on pages 51–53.
• The remote control buttons will not be able operate other equipment unless preset with the method above.
RECEIVER
47
En
48
En
Controlling the Rest of Your System
Clearing the Preset Codes
Clears all presets, all learned functions and restores the factory presets.
1 While pressing the
ENTER button
press and hold the
0
button for three seconds.
The LED on the remote control blinks three times indicating all the preset codes have been cleared. The remote control will reset as described in the box below.
RECEIVER
SIGNAL SELECT
SOURCE
SLEEP
DVD TV / SAT FRONT
DIMMER
DVR/ VCR F M / A M
AUTO
SURROUND ADVANCED
SOUND
MODE
SETUP TEST TONE CH_SELECT
ROOM
SETUP
ENTER
MUTE
MASTER
VOLUME
TOP MENU DISPLAY T.EDIT
MENU
P
ST
TUNE
ENTER
ST
MENU
AUDIO
P
EXIT
EON
TUNE
SUBTITLE
RF ATT
GUIDE
A
SEARCH
E
CLASS
C
MPX
D
D.ACCESS
E
ENTER
10
TV CONTROL
CHANNEL
INPUT
SELECT
CHANNEL VOLUME
1
1
RECEIVER
Input/Control
Mode Select button
DVD
TV/SAT
DVR/VCR
Preset
Code
000
600
456
Component
(Manufacturer)
DVD (PIONEER)
TV (PIONEER)
DVD Recorder
(PIONEER)
VCR (PIONEER) FRONT
TV
CONTROL
400
600 TV (PIONEER)
Controlling the Rest of Your System
CD/MD/CD-R/VCR/DVD/LD/DVD recorder/Cassette Deck Controls
This remote control can control these components after entering the proper codes or teaching the receiver the commands (see page 47).
Use Input/Control Mode Select buttons to put the remote control in the stated mode.
¡
1
3
7
N u m b e r
B u t t o n s
B u t t o n ( s )
S O U R C E
4
¢
8
F u n c t i o n
P r e s s t o s w i t c h t h e c o m p o n e n t s b e t w e e n S T A N D B Y a n d
P r e s s s k i p s t o t o r e t u t h e r n s t a r t o t t o f h e p r s t a r t e v i o u o s f t t r h e a c c u r r e n t k s o r c h a t r a c k p t e r .
o r c h a p t e r .
R e p e a t e d p r e s s e s
P l a y t h e r e v e r s e s i d e o f t h e t a p e o n a r e v e r s i b l e d e c k .
P r e s s s k i p s t o t o a d v t h e a n c e s t a r t t o o f t h f o e l l o s t a r t o f w i n g t h e t r a c k s n e x t o r c t r a c k h a p t o e r .
r c h a p t e r .
R e p e a t e d p r e s s e s
P l a y t h e f o r w a r d s i d e o f t h e t a p e o n a r e v e r s i b l e d e c k .
P a u s e p l a y b a c k o r r e c o r d i n g .
+ 1 0 B u t t o n
’ ‘
M E N U
T O P M E N U
A U D I O
S U B T I T L E
} ’
& E N T E R
H o l d d o w n f o r f a s t f o r w a r d p l a y b a c k .
H o l d d o w n f o r f a s t r e v e r s e p l a y b a c k .
S t a r t p l a y b a c k .
S s t o p t o p p p l a y e d b a w i l l c k ( o n c a u s e s o m e t h e d m i s c o d t r e l s , a y p t o r e s s o p e i n g n ) .
t h i s w h e n t h e d i s c i s a l r e a d y
D i r e c t l y a c c e s s t r a c k s o n a p r o g r a m s o u r c e .
D i r e c t l y a c c e s s c h a p t e r o n a p r o g r a m s o u r c e .
D i r e c t l y s e l e c t a c h a n n e l .
S n e u l e c t m b e t r a r t c o k s g e o r t t c h h e a p t e r t r a c k h o i r g h e c h r a t h a n p t e r
1 0 .
( + 1 0
P
B r e u s s t t o t h i s n + b
3 u
= t t o n a n d t r a c k o r t h c h e a r e m a i n i n g p t e r 1 3 ) .
S w i t c h e s s u b t i t l e s f o r D V D o r v i d e o g a m e c o n t r o l p a d .
S t a r t r e p r e s s e d c t o r d i n g .
o g e t h e r
T
.
o p r e v e n t a c c i d e n t a l r e c o r d i n g , t h e s e b u t t o n s m u s t b e
D i s p l a y s m e n u s c o n c e r n i n g t h e c u r r e n t D V D o r D V R y o u a r e u s i n g .
D i s p l a y s t h e t o p m e n u o f t h e c u r r e n t D V D o r D V R y o u a r e u s i n g .
C h a n g e s t h e a u d i o t r a c k o f d i s c s w i t h m o r e t h a n o n e a u d i o t r a c k .
D i s p l a y s / c h a n g e s t h e s u b t i t l e s o n m u l t i l i n g u a l D V D s
N a v i g a t e D V D m e n u s / o p t i o n s .
C o m p o n e n t s
C D / M D / C D R / V C R / D V D / L D /
D V D r e c o r d e r / C a s s e t t e d e c k
C D / M D / C D R / D V D / L D /
D V D r e c o r d e r
C a s s e t t e d e c k
C D / M D / C D R / D V D / L D /
D V D r e c o r d e r
C a s s e t t e d e c k
C D / M D / C D R / V C R / D V D / L D /
D V D r e c o r d e r / C a s s e t t e d e c k
C D / M D / C D R / V C R / D V D / L D /
D V D r e c o r d e r / C a s s e t t e d e c k
C D / M D / C D R / V C R / D V D / L D /
D V D r e c o r d e r / C a s s e t t e d e c k
C D / M D / C D R / V C R / D V D / L D /
D V D r e c o r d e r / C a s s e t t e d e c k
C D / M D / C D R / V C R / D V D / L D /
D V D r e c o r d e r / C a s s e t t e d e c k
C D / M D / C D R / L D
D V D / D V D r e c o r d e r
V C R
C D / M D / C D R / V C R /
D V D / L D / D V D r e c o r d e r
V i d e o g a m e
V C R /
M D /
D V D
C D R r e c o r d e r /
/ C a s s e t t e d e c k
D V D / D V D r e c o r d e r
D V D / L D / D V D r e c o r d e r
D V D / L D / D V D r e c o r d e r
D V D / D V D r e c o r d e r
D V D / D V D r e c o r d e r
• Depending on the maker and individual model, there are some buttons that may not be able operate some equipment or may operate it in a different way.
49
En
50
En
Controlling the Rest of Your System
Cable TV/Satellite TV/Digital TV/TV Controls
This remote control can control these components after entering the proper codes or teaching the receiver the commands (see page 47).
Use Input/Control Mode Select buttons to put the remote control in the stated mode.
B u t t o n ( s )
T V
I N P U T
S E L E C T
C
+ /
H
−
A N N E L
V O L U
+ /
−
M E
M E N U
F u n c t i o n
P r e s s t o s w i t c h t h e T V o r C A T V b e t w e e n S T A N D B Y a n d
P r e s s t o s w i t c h t h e T V i n p u t .
S e l e c t c h a n n e l s .
A d j u s t t h e T V v o l u m e .
T a k e s y o u t o t h e T V m e n u o f t h a t s y s t e m .
C o m p o n e n t s
C a b l e T V / S a t e l l i t e T V / T V
C a b l e T V / S a t e l l i t e T V / T V
C a b l e T V / S a t e l l i t e T V / T V
T O
¡
P
1
4
¢
M E
D I S P L A Y
N U
8
7
+ 1 0 B u t t o n
N u m b e r
B u t t o n s
} ]
E N T E R
’ ‘
&
T a k e s y o u t o t h e g u i d e m e n u o f t h a t s y s t e m .
T a k e s y o u t o t h e p r e v i o u s c h a n n e l
A
E x i t s t h e m e n u y o u a r e v i e w i n g .
U s e t o m o v e b a c k a p a g e i n t h e m e n u .
B / R E D
U s e t o m o v e f o r w a r d a p a g e i n t h e m e n u .
E / B L U E
C
D
U
/ G
/ Y E
S e l e c t t o g e t c h a n n n e l t h e t r a c k s e
R E t
L L O W o
E N s e l e c t a s h i g h e r o r c h a p t h t e r a n
(
1
+ 1
0
0
.
P r e s s
B u t t o n t h i s
+ b
3 = u t t o n t r a c k a n d o r t h e r e m c h a p t e r a i
1 3 n i n g
) .
p e c i f i c T V c h a n n e l .
P r e s s t o s e l e c t o r a d j u s t a n d n a v i g a t e i t e m s o n t h e m e n u s c r e e n .
n u m b e r
C a b l e T V / S a t e l l i t e T V / T V
C a b l e
D i g i t a l
T V /
T V
S a t e l l i t e T V / T V /
C a b l e
D i g i t a l
T V /
T V
S a t e l l i t e T V / T V /
T V
S a t e l l i t e T V
C a b l e
T V
T V / S a t e l l i t e T V / D i g i t a l
C a b l e T V
S a t e l l i t e T V / D i g i t a l T V
C a b l e T V
S a t e l l i t e T V / D i g i t a l T V
S a t e l l i t e T V / D i g i t a l T V
S a t e l l i t e T V / D i g i t a l T V
T V
C a b l e T V / S a t e l l i t e T V / T V
C a b l e T V / S a t e l l i t e T V / T V
• Depending on the maker and individual model, there are some buttons that may not be able operate some equipment or may operate it in a different way.
Controlling the Rest of Your System
Manufacturer
SONY
PHILIPS
HITACHI
RADIOLA
MITSUBISHI
DENON
TELEFUNKEN
PIONEER
TV
Manufacturer
PHILIPS
SONY
GRUNDIG
PANASONIC
TOSHIBA
TELEFUNKEN
SHARP
SAMSUNG
HITACHI
SABA
BRANDT
SANYO
THOMSON
FERGUSON
NOKIA
MITSUBISHI
SCHNEIDER
GOLDSTAR
BLAUPUNKT
NORDMENDE
RADIOLA
JVC
DAEWOO
ORION
SIEMENS
ACURA
ADMIRAL
AKAI
AKUBA
ALBA
DVD
Manufacturer
TOSHIBA
SONY
PANASONIC
JVC
SAMSUNG
SHARP
AKAI
RCA
DENON
HITACHI
PHILIPS
ZENITH
THOMSON
S O N Y
(video game)
LOEWE
GOLDSTAR
PIONEER
LD
Preset Code List
Code
001
002
003
004
005
006
007
009, 011
003, 010
012
013
014
015
016
013
014
000, 003, 008, 111
Code
101, 102
104
109
104
100
110
100
100, 111(DVD/LD)
Code
607, 631, 634, 656
604
631, 653
608, 622, 631, 642
605, 653
636, 637, 652
602
607, 638, 644, 646
606, 631, 633, 634,
636, 642, 643, 654
631, 636, 642, 651
636
635, 645, 648
636, 651, 652
607, 636, 651
632, 642, 652
609, 631
607, 641, 647
607, 650
631
632, 636, 651, 652
607
613
607, 644, 656
607, 632, 639, 640
631
644
631
632, 635, 642
641
607, 639, 641, 644
A M S T R A D
ANITECH
ASA
ASUKA
AUDIOGONIC
BASIC LINE
BAUR
BEKO
BEON
BLUE SKY
BLUE STAR
BPL
BTC
BUSH
CASCADE
CATHAY
CENTURION
CGB
CIMLINE
CLARIVOX
CLATRONIC
CONDOR
CONTEC
CROSLEY
CROWN
CRYSTAL
CYBERTRON
DAINICHI
DANSAI
DAYTON
DECCA
DIXI
DUMONT
ELIN
ELITE
ELTA
EMERSON
ERRES
FINLANDIA
FINLUX
FIRSTLINE
FISHER
FORMENTI
FRONTECH
FRONTECH/
PROTECH
FUJITSU
FUNAI
GBC
GEC
GELOSO
GENEXXA
GOODMANS
GORENJE
GPM
GRAETZ
GRANADA
GRANDIENTE
GRANDIN
HANSEATIC
HCM
HINARI
HISAWA
HUANYU
607
607
642
644
607
638
638
644
632
638, 644
642
641
641
607
644
607, 648
642, 644, 647
644
645
641
607, 636
641, 644
607, 631, 642
638
607
641
618
618
641
607, 641, 642, 644,
647, 656
644
607, 644
653
607
641
644
642
607
635, 643, 655
607, 632, 645, 648,
653, 654, 655
640, 644
632, 635, 638, 645
607, 632, 642
631, 642, 646
632
648
640, 646
632, 642
607, 634, 648
632, 644
631, 641
607, 639, 647, 648,
656
638
641
631, 642
607, 635, 642, 643,
648
657
618
607, 642
618, 644
607, 641, 644
618
656
H Y P S O N
ICE
IMPERIAL
INDIANA
INGELEN
INTERFUNK
INTERVISION
ISUKAI
ITC
ITT
JEC
KAISUI
KAPSCH
KENDO
KENNEDY
KORPEL
607, 618, 646
646, 647
638, 642
607
631
607, 631, 632, 642
646, 649
641
642
631, 632, 642
605
618, 641, 644
631
642
632, 642
607
KOYODA
LEYCO
644
607, 640, 646, 648
LIESENK & TTER 607
LOEWE 607
LUXOR 632, 642, 643
M ELECTRONIC 631, 644, 645, 654,
655, 656
M-ELECTRONIC 607, 636, 651
MAGNADYNE
MAGNAFON
MANESTH
MARANTZ
632, 649
649
639, 646
607
MARK
MATSUI
607
607, 639, 640, 642,
644, 647, 648
634 MCMICHAEL
MEDIATOR
MEMOREX
METZ
MINERVA
607
644
631
631, 653
MULTITECH 644, 649
NECKERMANN 607, 631
NEI
NIKKAI
607, 642
605, 607, 641, 646,
648
649 NOBLIKO
OCEANIC
OSAKI
OSO
OSUME
631, 632, 642
641, 646, 648
641
648
OTTO VERSAND 607, 631, 632, 642
PALLADIUM 638
PANAMA 646
PATHO CINEMA 642
PAUSA
PHILCO
644
632, 642
PHOENIX
PHONOLA
PROFEX
PROTECH
QUELLE
632
607
642, 644
607, 642, 644, 646,
649
607, 631, 632, 642,
645, 653
607 R-LINE
RBM
REDIFFUSION
REX
ROADSTAR
SAISHO
SALORA
SAMBERS
SBR
653
632, 642
631, 646
641, 644, 646
639, 644, 646
631, 632, 642, 643
649
607, 634 51
En
52
En
Controlling the Rest of Your System
SCHAUB LORENZ 642
SEG
SEI
642, 646
632, 640, 649
SELECO
SIAREM
SINUDYNE
SKANTIC
631, 642
632, 649
632, 639, 640, 649
643
SOLAVOX
SONOKO
SONOLOR
SONTEC
SOUNDWAVE
STANDARD
STERN
SUSUMU
631
607, 644
631, 635
607
607
641, 644
631
641
SYSLINE
TANDY
TASHIKO
TATUNG
607
631, 641, 648
634
607, 648
TEC
TELEAVIA
TELETECH
TENSAI
THORN
642
636
644
640, 641
TOMASHI
TOWADA
ULTRAVOX
UNIVERSUM
607, 631, 642, 645,
648
618
642
632, 642, 649
607, 631, 638, 642,
645, 646, 654, 655
607 VESTEL
VOXSON
WALTHAM
WATSON
WATT RADIO
631
643
607
632, 642, 649
WHITE
WESTINGHOUSE 607
YOKO
PIONEER
607, 642, 646
600, 607, 631, 632,
636, 642, 651
STB (SATELLITE/CATV)
Manufacturer
JERROLD
SA
ZENITH
PIONEER
On digital STB
Manufacturer
PIONEER
VCR
Code
716
706, 708
717
200, 204, 231, 700
Code
200
Manufacturer
PHILIPS
PANASONIC
THOMSON
SONY
JVC
GRUNDIG
AKAI
HITACHI
Code
414, 428
408, 432
417, 428, 449
416, 417, 457, 458
459
407, 417, 428
408, 414, 441, 453
454, 455
417, 442
406, 417, 441
TOSHIBA
MITSUBISHI
SHARP
ORION
SANYO
FERGUSON
BLAUPUNKT
NOKIA
SELECO
AIWA
AKIBA
ALBA
405, 409, 414, 417
428
407, 409, 414
402
424, 445, 446
444
417, 449, 450
408, 417, 432, 455
417, 442, 444
417
441, 446
453
424, 446, 447, 448
452
452 AMBASSADOR
AMSTRAD
ANITECH
ASA
BAIRD
BASIC LINE
BRANDT
441
453
411, 414
417, 441, 444, 450
448, 452, 453
449, 451
BRANDT
ELECTRONIQUE 417
BUSH 424, 446, 447, 448
453
CATRON
CGB
CIMLINE
CLATRONIC
452
441
453
452
CONDOR
CROWN
DAEWOO
DANSAI
DE GRAAF
DECCA
DUAL
DUMONT
ELCATECH
FIDELITY
FINLANDIA
FINLUX
FIRSTLINE
452
448, 452, 453
448, 452
453
406
414, 441
417
414, 441, 444
453
441
414, 444
406, 414, 441, 444
405, 409, 411, 424
453
444
452
FISHER
FRONTECH
FUNAI
GBC
GENERAL
GOLDSTAR
GOODMANS
441
414
452
411
411, 441, 448, 452
453
417, 444
414, 444
GRAETZ
GRANADA
GRANDIENTE
GRANDIN
HCM
HINARI
HYPSON
IMPERIAL
441
411, 441, 453
453, 454
445, 446, 453, 454
453
441
414
417, 428, 442, 444
INTERFUNK
ITT
ITV
KAISUI
KENDO
KORPEL
LEYCO
LOEWE
411, 448
453
424, 444
453
453
411, 414, 432
LUXOR 409, 442, 444
M-ELECTRONIC 441
MANESTH 405, 453
MARANTZ
MATSUI
MEMOREX
MEMPHIS
414
424, 445, 446
411, 441, 444
453
METZ
MINERVA
MULTITECH
MURPHY
432, 455
455
441, 453
441
NBC 407, 417
NECKERMANN 414
NESCO
NORDMENDE
453
417, 428
OCEANIC
OSAKI
417, 441
411, 441, 453
OTTO VERSAND 414
PALLADIUM 411, 417, 453
PATHE MARCONI 417
PENTAX 406
PERDIO
PHONOLA
441
414
PORTLAND
PROLINE
PYE
QUELLE
RADIOLA
REX
ROADSTAR
SABA
452
441, 454
414
414
414
417, 428
411, 448, 453
417, 428, 449
SAISHO
SALORA
SANSUI
SBR
424, 445
409, 442
407, 417
414
SCHAUB LORENZ 417, 441
SCHNEIDER 414, 441, 453
SEI
SENTRA
414
452
SHINTOM
SIEMENS
SINGER
SINUDYNE
SOLAVOX
SUNSTAR
SUNTRONIC
TASHIKO
453
411, 444, 455
405
414
452
441
441
441
TATUNG
TEC
TELEAVIA
TELEFUNKEN
TENOSAL
TENSAI
THORN
UNIVERSUM
YAMISHI
YOKAN
YOKO
PIONEER
414, 417, 441
452
417
417, 428, 449, 451
453
441
417, 444
411, 414, 441, 442
455
453
453
452
400, 407, 414, 443
DVD Recorder
Manufacturer
PIONEER
TAPE
Code
456
Manufacturer
AKAI
A R C A M
DENON
FISHER
GRUNDIG
J V C
KENWOOD
L U X M A N
M A R A N T Z
M E M O R E X
MITSUBISHI
NAKAMICHI
ONKYO
PHILIPS
SANSUI
SHERWOOD
SONY
TANDBERG
TECHNICS
TOSHIBA
YAMAHA
PIONEER
CD
Manufacturer Code
AKAI
ARCAM
ASUKA
AUDIO TON
335
336
337
336
332 BUSH
CALIFORNIA
AUDIO LAB
CYRUS
DENON
DUAL
FISHER
GOLDSTAR
GRUNDIG
HITACHI
INTERSOUND
JVC
KENWOOD
KODAK
LINN
LUXMAN
304
336
309
319, 337
340
330
336
334
337
331
310, 311
322
336
341
M ELECTRONIC 344
MARANTZ 304, 336
MATSUI
MCS
MEMOREX
MERIDIAN
336
304
300
336
MITSUBISHI
NAD
NAIM
ONKYO
PANASONIC
PHILIPS
QUAD
335
316
336
342
304
322, 336
336
Code
829
810
810, 827
813
821
802
804, 807, 822
815
821
825
829
816
817, 819
821
824
818
814, 823
820
803
826, 828
811, 822
800, 825
Controlling the Rest of Your System
QUASAR
R O A D S TA R
ROTEL
S A B A
S A N Y O
S H A R P
S O N Y
304
344
336
319
340
343
316, 329
TECHNICS 304, 333
TELEFUNKEN 319
THOMSON
UNIVERSUM
319
336
YAMAHA
PIONEER
338, 339
300
CD-R
Manufacturer
PIONEER
PHILIPS
DENON
MARANTZ
MD
Code
345
346
346
346
Manufacturer
SONY
KENWOOD
SHARP
TEAC
ONKYO
DENON
PIONEER
DAT
Manufacturer
PIONEER
Code
901
903
902
904
905
906
900, 902,
Code
907
CAUTION:
• You may not be able to use a particular code even if it is listed in these pages.
53
En
10
Additional Information
Troubleshooting
Incorrect operations are often mistaken for trouble and malfunctions. If you think that there is something wrong with this component, check the points below. Sometimes the trouble may lie in another component. Investigate the other components and electrical appliances being used. If the trouble cannot be rectified even after exercising the checks listed below, ask your nearest PIONEER authorized service center or your dealer to carry out repair work.
54
En
Symptom
The power does not turn on.
AMP ERR blinks in the display and the unit turns off.
HEAT UP blinks in the display.
OVERHEAT blinks in the display and no sound is output.
THDCT NG blinks in the display and no sound is output.
The unit does not respond when the buttons are pressed.
No sound is output when the AM/FM is selected.
Considerable noise in radio broadcasts.
Broadcast stations cannot be selected automatically.
activated.
panel.
Cause
• The power plug is disconnected.
• The protection circuit may have been
• Speaker wire may be touching the rear
• Static electricity caused by dry air.
• The receiver has a serious problem.
• The receiver has gotten too hot.
• The receiver has gotten too hot.
• The thermistor (temperature sensor) is out of order.
• Improper connections.
• Sound is muted.
• The volume is turned down.
• Incorrect frequency.
• The antenna is not connected.
Remedy
• Connect the power plug to the wall outlet.
• Disconnect the power plug from the outlet, and insert again.
• Make sure there are no loose strands of speaker wire touching the rear panel. This could cause the receiver to shut off automatically.
• Disconnect the power plug from the outlet, and insert again.
• Unplug the receiver from the wall and call a
Pioneer-accredited repair center.
• Allow the receiver to cool down with good ventilation. If problem persists turn off receiver, unplug from wall and allow it to cool down.
• Turn the receiver off and allow it to cool down with good ventilation. If problem persists turn the volume down.
• Turn the receiver off, unplug from wall and call a Pioneer-accredited repair center.
• Make sure the component is connected correctly (refer to pages 12–15).
• Press MUTE on the remote control.
• Adjust the MASTER VOLUME.
• Tune in the correct frequency.
• Connect the antenna (refer to page 18).
FM broadcasts
• The FM antenna is not fully extended or is poorly positioned.
• Weak radio signals.
• Fully extend the FM wire antenna, position for best reception, and secure to a wall.
• Connect an outdoor FM antenna (refer to page 18).
AM broadcasts
• The AM antenna is poorly positioned.
• Weak radio signals.
• Interference caused by other equipment
(fluorescent lamp, motor, etc.).
• The radio signal is too weak .
• Adjust the direction and position for best reception.
• Connect an additional internal or external
AM antenna (refer to page 18).
• Turn off the equipment causing the noise or move it away from the receiver.
• Place the antenna farther away from the equipment causing the noise.
• Connect an outdoor antenna (refer to page
18).
Additional Information
Symptom
No sound from surround or center speakers.
No sound from subwoofer
Sound is produced from analog components, but not from digital ones
(DVD, LD, CD-ROM etc.).
Cause Remedy
• Surround or center speaker settings are incorrect.
• The surround and/or center levels are turned down.
• The surround and/or center speakers are disconnected.
• Refer to speakers setting mode on page
28 to check the speaker settings.
• Turn levels up. Refer to “Setting the
Volume Level of Each Channel” on page
32 to check the speaker levels.
• Connect the speakers (refer to page 16).
• The subwoofer is disconnected.
• The subwoofer's settings are incorrect.
• The subwoofer's levels are too low.
• The LFE Attenuator is set to OFF.
• Connect the subwoofer (refer to page 16).
• Set the subwoofer (refer to page 28).
• Set the front speakers to Small ( S ) (refer to page 28).
• Refer to “Setting the Volume Level of
Each Channel” on page 32 to check the speaker levels.
• Set the LFE Attenuator to either 0 dB or
10 dB (refer to page 29).
• Digital connections are incorrect.
.
• The digital output of the player is turned off.
• Make digital connections (refer to page
11–14)
• Turn on the digital output of the player on (consult the manual that came with the player, if necessary).
• Use a player that is compatible with this receiver.
• The CD-ROM player is outputting a data stream (not an audio signal) which is incompatible with this receiver.
• Digital connections are incorrect.
• Analog input has been selected.
• The digital input assignment is wrong.
• Make digital connections (refer to page
11–14).
• Select digital input (refer to page 44).
• Assign the digital input (refer to page 31).
No sound is output or a noise is output when
Dolby Digital/DTS software is played back.
When a search is performed by a DTS compatible CD player during playback, noise is output.
The Dolby/DTS indicator doesn't light when playing Dolby/DTS software.
When playing a 96 kHz/
24bit disc the sound is too loud.
• A DVD player not compatible with
Dolby Digital/DTS is being used.
• The settings on the DVD player are incorrect and/or the DTS signal output is turned off.
• The digital output level is turned down on a CD player or other component equipped with digital output level adjustment capability. (The DTS signal has been altered by the player, and cannot be read.)
• Make sure your DVD player is compatible with Dolby Digital/DTS.
• Make sure the player's settings are correct and/or the DTS signal out is on.
Refer to the instruction manual supplied with the DVD player.
• Set the digital volume level of the player to full, or to the neutral position.
• The search function performed by the player slightly alters the digital information, making it unreadable.
• This is not a malfunction, but be sure to turn the volume down to prevent the output of loud noise from your speakers.
• The player is paused.
• The player's sound output settings are wrong.
• Press play.
• Set the player correctly (consult the manual that came with the player, if necessary).
• Different discs have different recording levels so some may be louder than others.
• Turn the volume down.
55
En
Additional Information
56
En
Symptom Cause Remedy
The sound distorts.
• The analog signal is too strong.
• Master volume is too loud.
You can only hear treble from speakers.
• The front speakers are set to small.
• Turn on input attenuator (see page 30).
• Turn the volume down.
• Set the front speakers to large (refer to page 28).
No image is output when an input is selected.
• The video connections are incorrect.
• The input source is not properly selected.
• The DVD/video player settings are incorrect.
• Make sure the video component is connected correctly (refer to pages 11 to 14).
• Make sure the proper component is selected by pressing the correct function button (see page 20).
• Set correctly. Refer to the instruction manual supplied with the DVD/video player.
The settings have all been cleared.
• The receiver has been unplugged or the main power turned off for more than a month.
• Set the receiver again (refer to page 26-
30).
OVERLOAD blinks in the display and the power turns off automatically.
• There is a short in your speaker cable.
• The output is too high.
• Fix the short or get new speaker cable.
• Turn the volume down.
You can't set the subwoofer frequency route.
• All the speakers are set to either large or
NO (i.e. no speakers are set to small).
• Change the speaker settings (refer to page
27–29).
The display is dark or off.
• The DIMMER feature is set to dark or off.
• Press DIMMER on the remote control repeatedly to select a different brightness.
After making an adjustment the display goes off.
• The DIMMER feature is set to off.
• Press DIMMER on the remote control repeatedly to select a different brightness.
The receiver cannot be remote controlled.
• The remote control batteries have worn out.
• You are too far away or at a bad angle for operation.
• There is an obstacle between the receiver and the remote control.
• Strong light such as fluorescent light.
• Replace the batteries (refer to page 10).
• Operate within 7 m, 30° of the remote sensor on the front panel (refer to page
10).
• Remove the obstacle or operate from another angle of position.
• Avoid exposing the remote sensor on the front panel to direct light.
• Disconnect the CONTROL terminal.
• The CONTROL terminal has been hooked up.
Other components cannot be remote controlled.
• The proper code hasn't been input into the remote control to control that component.
• The remote control is in a mode to make some setting or control something on the receiver.
• Something is plugged into the "CON-
TROL IN Terminal " (see page 19).
• Input the proper code into the remote control (see page 47).
• Press the button of the component you want to control.
• Either point remote at the remote sensor of the unit that is plugged into the "Control Terminal in" or unplug the cable from the "CONTROL IN
Terminal" and use remote normally.
The shutter of the optical terminal doesn’t close after removing plug.
• The plug was inserted improperly.
• The terminal is fine but the shutter won’t close.
If the unit does not operate normally due to external effects such as static electricity.
Disconnect the power plug from the outlet and insert again to return to normal operating conditions.
Techno Know How
Understanding DVD Packaging
DVD packaging usually states what sound formats are included on the DVD.
The diagram here shows what you might see on a typical DVD box. The terms used (Dolby Digital, etc.) are explained in the following sections.
LANGUAGE
CAPTIONS
SUBTITLES
English
5.1
SURROUND
5.1
SURROUND
Captioned
Digital Audio Formats
Home theater uses various types of methods to encode the sound on to the digital sources and these are known as digital formats. The most common digital formats are explained below.
Dolby Digital and Dolby Surround
1
Dolby Digital is the most widely used system to record soundtracks on DVDs and other media. It's a sound compression format which records the sound of 6 channels of the theater surround system (Dolby Digital) on a movie film digital track. Of the 6 channels, the subwoofer channel is intended for bass only, and because the frequency range is smaller than a main channel, the overall soundtrack is called 5.1 channels.
Dolby Digital is the name of the Dolby surround multichannel digital system that was developed after the Dolby
Surround System and Dolby Pro Logic Surround System.
Dolby Digital is also known as the 5.1 channel system. It is equipped with 5 channels (front left, front right, center, surround left, surround right) in the frequency range from 20 Hz to 20 kHz and an independent Low
Frequency Effect (LFE) channel. The subwoofer channel is also called Low Frequency Effect (LFE).
This channel can be used with a powered subwoofer to get strong bass sounds.
R
DTS
DTS is another widely used system to record soundtracks on DVDs and other media. It has been adopted as a sound recording format in the latest movie theaters since the release of “JURASSIC PARK” in 1993, and has a good reputation for high quality sound and dynamic surround effects.
In this system, 6 channels of digital sound are recorded on CD-ROM, rather than on the film. DTS adopts a simultaneous playback format. With a low rate of compression of sound signals and a high rate of transmittance, a higher sound quality format is produced. Also, unlike the process of recording digital sounds on film directly, the only components required are a CD-ROM player as might be used with a personal computer and a DTS processor, and therefore less investment is required than with other formats. For this reason, the format is being introduced in more and more movie theaters, and is being adopted in home movie software (DVD, LD) and music software (5.1 channel CD).
PCM (Pulse Code Modulation)
This is an uncompressed 2 channel stereo format found on most CDs and DATs. PCM can be used as one of the audio recording formats for DVD but as it's only 2 channel stereo. It is sometimes used for DVD audio discs (or
DVD-A).
11
57
En
Techno Know How
Recording Formats
These are the recording formats. Determining what kind of playback format is being employed with any particular recording format depends on three things: 1) how the signal is encoded and transmitted; 2) how the signal is decoded; and 3) how the sound is actually heard through the speakers (where your speaker configuration and the sound mode you choose have a big effect).
All the possibilities are listed below.
2 Channel Stereo
In this format the signal is recorded on two channels (i.e. stereo), left and right. Most music CDs use this format.
2 Channel Surround (Dolby Surround)
Used mainly for videotape, this is one of the original home theater formats and can be decoded by this receiver.
Because it developed over a time it is the most complicated system explained here. The developers had to solve the problem of how to offer surround sound to the people who had the proper decoder but at the same time deliver 2 channel sound to those without the proper decoder. Thus the Dolby Surround format encodes four channels (left, right, center, surround) into two channels for storage and transmission.
5.1 Channel Surround
This is a format with five channels (front left & right, center, surround left & right) and a channel for bass. (This is called the LFE channel and is usually output from a subwoofer. Since it is only for bass sounds it is thus expressed as .1 of a channel.) With this format you can get movie theater-like, powerful surround sound.
58
En
Playback Formats
This receiver is equipped with many different playback formats and this flexibility should allow you to get stereo or surround sound playback (depending on the kind of source you're using) with all speaker configurations.
2 Channel Stereo Playback
This is conventional stereo playback from the left and right speakers (called "front" speakers on this receiver).
Virtual Surround Playback (PHONES/VIRTUAL indicator lights)
With this playback method you can get multichannel-like surround sound even when using just two speakers.
This is achieved by the Virtual surround listening mode which uses SRS Tru Surround technology.
Headphone Surround Playback (PHONES/VIRTUAL indicator lights)
With this playback method you can get multichannel-like surround sound like effects even when listening on headphones. This new technology is useful for getting a surround sound feeling even when listening with the privacy of headphones.
Dolby Pro Logic II Playback (
2
PRO LOGIC II indicator lights)
Dolby Pro Logic II
Dolby Pro Logic II is an improved version of Dolby Pro Logic technology with extended matrix decoding technology that can create 5.1 channel sound playback from two channel sources. Dolby Pro Logic II creates basic
5 channel sound by using the innovative "steering logic" circuit. Therefore when listening to typical two-channel sources like CD, the listener can enjoy a richer spatial effect. When using software encoded with Dolby Surround, this decoding system affords the listener an improved surround experience with greater sound detail.
This unit has a three Dolby Pro Logic II functions. The first is "MOVIE" (suitable for film soundtracks); "MUSIC"
(suitable for music); "Pro Logic Mode" (this mode is less sensitive to the quality of the source material, so may be useful when Movie Mode or Music Mode do not give good results). One can select one of them for playback depending on your soundtrack of choice.
Multichannel Surround Playback (ADVANCED indicator lights)
These are different multichannel playback methods which are each suited to various sources. These modes will give you realistic and powerful surround sound playback for five speakers.
Techno Know How
Specifications
Amplifier Section
Continuous Power Output (STEREO MODE)
FRONT ...... 25 W + 25 W (DIN 1 kHz, THD 1 %, 8
Ω
)
Continuous Power Output (SURROUND MODE)
FRONT ..................... 30 W/ch (1 kHz, THD 1 %, 8
Ω
)
CENTER ....................... 30 W (1 kHz, THD 1 %, 8
Ω
)
SURROUND ............. 30 W/ch (1 kHz, THD 1 %, 8
Ω
)
Continuous Power Output (STEREO MODE)
FRONT ...... 25 W + 25 W (DIN 1 kHz, THD 1 %, 8
Ω
)
RMS Power Output
FRONT ................... 41 W/ch (1 kHz, THD 10 %, 6
Ω
)
CENTER ..................... 41 W (1 kHz, THD 10 %, 6
Ω
)
SURROUND ........... 41 W/ch (1 kHz, THD 10 %, 6
Ω
)
• Above specifications are applicable when the power supply is 230V.
Input (Sensitivity/Impedance)
DVD, TV/SAT, DVR/VCR, FRONT ....... 200 mV/47 k
Ω
Frequency Response
DVD, TV/SAT, DVR/VCR, FRONT
Output (Level/Impedance)
VCR OUT ........................................... 200 mV/2.2 k
Ω
Signal-to-Noise Ratio
[DIN (Continuous rated power output/50 mW)]
DVD, TV/SAT, DVR/VCR, FRONT ............ 88 dB/64 dB
VIDEO Section
Input (Sensitivity/Impedance)
DVD, TV/SAT, DVR/VCR, FRONT ........... 1 Vp-p/75
Ω
Output (Level/Impedance)
DVR/VCR, MONITOR ............................. 1 Vp-p/75
Ω
Frequency Response
DVD, TV/SAT, DVR/VCR, FRONT
→
MONITOR
................................................ 5 Hz to 7 MHz +0
–3
dB
Signal-to-Noise Ratio .......................................... 55 dB
FM Tuner Section
Frequency Range ...................... 87.5 MHz to 108 MHz
Usable Sensitivity
........................ Mono:15.2 dBf, IHF (1.6 µV/ 75
Ω
)
50 dB Quieting Sensitivity ................... Mono: 20.2 dBf
....................................................... Stereo: 41.2 dBf
Signal-to-Noise Ratio ............. Mono: 76 dB (at 85 dBf)
.......................................... Stereo: 72 dB (at 85 dBf)
Distortion .................................. Stereo: 0.6 % (1 kHz)
Alternate Channel Selectivity ............. 70 dB (400 kHz)
Stereo Separation ................................... 40 dB (1 kHz)
Frequency Response .............. 30 Hz to 15 kHz (±1dB)
Antenna Input (DIN) ........................ 75
Ω
unbalanced
AM Tuner Section
Frequency Range ...................... 531 kHz to 1,602 kHz
Sensitivity (IHF, Loop antenna) .................... 350 µV/m
Selectivity ........................................................... 30 dB
Signal-to-Noise Ratio .......................................... 50 dB
Antenna .................................................. Loop antenna
Miscellaneous
Power Requirements
UK model ........................... AC 220 – 230 V, 50/60 Hz
European model ................. AC 220 – 230 V, 50/60 Hz
Power Consumption ......................................... 120 W
In Standby ....................................................... 0.75 W
Dimensions ............... 420 (W) x 65 (H) x 319 (D) mm
Weight (without package) .................................. 4.8 kg
Furnished Parts
AM loop antenna ....................................................... 1
FM wire antenna ........................................................ 1
Dry cell batteries (AA size IEC R6P) ........................... 2
Remote control unit ................................................... 1
Power cord ................................................................ 1
Speaker cord labels .................................................... 1
Operating instructions ............................................... 1
• Specifications and the design are subject to possible modifications without notice, due to improvements.
59
En
Published by Pioneer Corporation.
Copyright © 2002 Pioneer Corporation.
All rights reserved.
PIONEER CORPORATION
4-1, Meguro 1-Chome, Meguro-ku, Tokyo 153-8654, Japan
PIONEER ELECTRONICS [USA] INC.
P.O. BOX 1540, Long Beach, California 90801-1540, U.S.A.
PIONEER ELECTRONICS OF CANADA, INC.
300 Allstate Parkway, Markham, Ontario L3R OP2, Canada
PIONEER EUROPE NV Haven 1087, Keetberglaan 1, B-9120 Melsele, Belgium TEL: 03/570.05.11
PIONEER ELECTRONICS AUSTRALIA PTY. LTD.
178-184 Boundary Road, Braeside, Victoria 3195, Australia, TEL: [03] 9586-6300
PIONEER ELECTRONICS DE MEXICO S.A. DE C.V.
San Lorenzo 1009 3er Piso Desp. 302 Col. Del Valle Mexico D.F. C.P. 03100
TEL: 55-5688-5290
<TNGZC/02C00001> Printed in china <ARB7260-A>
advertisement
Related manuals
advertisement