HP Engage One Prime User Guide
HP Engage One Prime is a compact and versatile thermal printer designed for various applications. It offers high-quality printing at speeds of up to 90mm/s, with a maximum print width of 48mm and a resolution of 203 x 203 DPI. The printer supports multiple international character sets, including Traditional Chinese, Simplified Chinese (GB2313/18030), Japanese, Korean, English, and HK. It also features a range of 1D and 2D barcodes, making it suitable for retail, hospitality, and other industries.
Advertisement
Advertisement
User Guide
© Copyright 2019 HP Development Company,
L.P.
Linux® is the registered trademark of Linus
Torvalds in the U.S. and other countries.
The information contained herein is subject to change without notice. The only warranties for
HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein.
RMN: HSTN-RP01
First Edition: May 2019
Document Part Number: L67803-001
Table of contents
iii
iv
1 General best practices
Before installing and using the printer, carefully read the following items. To keep your printer in optimal operating condition, follow these guidelines.
● Install the printer on a flat and stable surface.
● For convenient operation and maintenance, reserve adequate space around the printer.
● Keep the printer away from water, and avoid direct exposure to sun, strong light, and fire.
● Do not use or store the printer in a place exposed to high temperature, moisture, or serious pollution.
● Do not install the printer in a place exposed to vibration or impact.
● Do not allow condensation to form on the printer. If condensation does form, do not turn on the printer until the condensation has evaporated completely.
● Do not let water or conductive materials, such as metal, enter the printer. If this happens, immediately turn off the printer.
● If there is no paper loaded in the printer, do not attempt to print anything. Printing when no paper is loaded damages both the print head and platen roller.
● To ensure print quality, use the recommended paper.
● To keep the print head in good condition, set the print darkness to the lowest grade that provides acceptable print quality.
● Only a manufacturer-certified technician should disassemble or repair the printer.
● When necessary, reference this user guide.
1
2 Specifications
Printing specifications
Table 2-1 Printer specifications and their parameters
Printer specification
Print method
Print resolution
Paper width
Print width
Print speed
USB interface
Cash drawer interface
Memory
Printer status detection
Cut mode
1D barcodes
2D barcodes
Fonts
Parameter
Direct line thermal printing
203 × 203 DPI
57.5 mm
Maximum 48 mm
Maximum 90 mm/s
USB 2.0 port (full speed)
Can control 1 or 2 cash drawers
● RAM: 8 MB
● Flash: 8 MB
● Paper end sensor/paper presence detection
● Open cover detection
● Print head temperature detection
● Printer voltage detection
● Cutter anomaly detection
● Full cut
● Partial cut
● UPC-A
● UPC-E
● Code 39
● Code 93
● Code 128
● EAN8
● EAN13
● ITF
● CODABAR
● PDF417
● QR
● GS1
● Font A: 12 × 24
2 Chapter 2 Specifications
Table 2-1 Printer specifications and their parameters (continued)
Printer specification Parameter
Character set
Character enlargement
Character rotation
Command
Paper type
Paper roll OD
Paper thickness
Power supply input
Human-machine interface power switch
Human-machine interface button
Lifetime of print head
Lifetime of cutter
Operation temperature and humidity
Storage temperature and humidity
Overall dimensions
● Font B: 9 × 17
● Kanji font A: 24 × 24
● 95 alphanumeric
● 14 types of international characters
● 128 × 68 code page
● User-defined font (95) and code page
● Optional: Traditional Chinese, Simplified Chinese
(GB2313/18030), Japanese, Korean, English, HK
Enlarge up to 6 times horizontally and vertically
Rotation printing in four directions (0°, 90°, 180°, 270°)
ESC/POS compatible
Thermal continuous paper
Maximum 51 mm
0.06 mm–0.08 mm thermal paper
9 V/3.6 A DC
Support
Support
≥ 50 Km (standard test sample with 12.5% duty ratio)
500,000 cuts (standard test condition)
-10°C–45°C, 20%–90% relative humidity (RH)
-30°C–65°C, 10%–95% RH
96 mm (L) × 96 mm (W) × 121 mm (H)
Cutter specifications
Table 2-2 Cutter specifications and their parameters
Cutter specification
Cutting method
Cutting time
Cutting interval
Applicable paper types
Operation voltage
Maximum operation current
Cutter lifetime
Parameter
Sliding blade
1 s (per cut)
2 s
0.06 mm–0.08 mm thermal paper
9 V DC
350 mA
500,000 cuts (standard test condition)
Cutter specifications 3
Paper specifications
Table 2-3 Paper specifications and their parameters
Paper specification
Paper type
Paper supply mode
Paper width
Paper thickness
Thermal layer
Paper roll
Parameter
Thermal paper
Paper roll
57.5 mm
0.06 mm–0.08 mm
Outward
Paper roll OD maximum ф51 mm, core ID minimum ф11.5 mm
NOTICE: Use either the recommended paper or an equivalent quality paper. Using low-quality paper might affect the print quality and shorted the lifetime of the print head.
Do not insert paper into the core shaft.
If the paper is contaminated by chemicals or oil, it might become discolored or lose heat sensitivity at the contaminated spot, which affects the print quality.
Do not rub the paper surface with hard objects, because this might affect the print quality.
If the environment temperature is above 70°C, the paper discolors. Do not use or store the paper in high temperature, high humidity, or strong light environments.
4 Chapter 2 Specifications
3 Components
Front and top
1
2
3
4
Table 3-1 Front and top components
Component
Top cover
Case
Button
Error light
Front and top 5
5
6
Table 3-1 Front and top components (continued)
Component
Base
Case cover
Light
Table 3-2 Light status and description
Status
Flashing slowly
Flashing slowly
Flashing slowly
Flashing slowly
Flashing slowly
Error
The print head is overheating.
The printer voltage is abnormal.
There is a cutter error.
The print head is lifted up.
The paper roll needs to be replaced.
NOTICE: The temperature of the print head is detected by a thermal resistor. If the print head is overheating, the protective circuit automatically turns off the power to the printer and stops the current print operation.
Bottom
7
8
Table 3-3 Bottom components
Component
Cash drawer connector
USB Type-C port and power connector
6 Chapter 3 Components
Internal
Table 3-4 Internal components
Component
13
14
15
9
10
11
12
Platen roller
Paper roll holder
Mechanism chassis
Print head
Pendulum block
Paper presence sensor
Guide paper board
Internal 7
4 Setup
Placing the printer
Use the following guidelines to properly place the printer.
● Place the printer horizontally on the table. The incline installation angle must not exceed 5°.
● Do not place the printer near a water source.
● Do not place the printer in an environment exposed to vibration and impact.
● Be sure that the printer power supply is grounded.
8 Chapter 4 Setup
● Be sure that there is space around the printer for convenience during operation and maintenance. There must be room to open the case 128°.
Downloading the drivers
1.
Go to http://www.hp.com/support and follow the instructions to find your product.
2.
Download and install the latest drivers.
Downloading the drivers 9
Connecting the printer to power
1.
Before setting up the printer, turn off the host computer and other attached devices.
2.
Connect a USB Type-C cable to the USB Type-C port and power connector.
3.
Connect the other end of the USB Type-C cable to a USB Type-C port and power connector connected to the host computer.
NOTE: Never disconnect from the computer while the printer is on.
Connecting the cash drawer
1.
Before setting up the printer, turn off the host computer and other attached devices.
2.
Connect the cash drawer cable to the cash drawer connector.
NOTE: Do not attempt to connect a telephone cable to the cash drawer connector.
Using the cable clip
1.
Insert the cables into the clip (1).
2.
Slightly tighten the clip (2).
10 Chapter 4 Setup
3.
Insert the end of the buckle into the hole on the printer case (3) and then slide the clip along the buckle until it cannot move (5).
4.
Connect the USB Type-C cable (5) and the cash drawer cable (6) to the appropriate ports.
5.
Be sure the cables are routed through the hole in the printer case (7), and then tighten the clip until it is locked (8).
Installing a paper roll
1.
Verify that you have the correct paper roll. See Paper specifications on page 4
.
2.
Turn off the printer.
3.
Rotate the top cover counterclockwise until the cover assembly ejects, and then open the cover assembly.
Installing a paper roll 11
4.
Place the paper roll into the paper compartment, and then pull the edge of the paper past the cover.
NOTE: Be sure the thermal side of the paper roll is exposed.
To prevent paper jams and other malfunctions, be sure that the paper is tightly rolled and that the paper is inserted in the middle of the paper guide stop.
Be sure that the paper roll is installed horizontally and not at an incline.
5.
Rotate the cover clockwise until it is fully closed.
Starting the printer
▲ After the printer is connected to the host computer and power via USB Type-C and a paper roll is installed, the light turns green. Press the paper feed button to prepare for printing.
12 Chapter 4 Setup
5 Maintenance
IMPORTANT: Before starting maintenance, be sure that power is disconnected from the printer.
Do not use organic solvents such as gasoline or acetone.
Do not restore power to the printer until the isopropyl alcohol completely evaporates.
Perform this maintenance cycle once a month.
Cleaning the print head and platen roller
1.
Turn off the printer and twist the top cover counterclockwise to open it.
2.
If you have recently printed, wait for the print head to cool completely.
3.
Dampen a piece of cotton with isopropyl alcohol, and use it to wipe the dust and stains from the surface of the print head and the platen roller.
4.
After the isopropyl alcohol has completely evaporated, close the top cover.
Cleaning the sensor
When the printer cannot identify the mark effectively, you must clean the sensor.
1.
Turn off the printer and twist the top cover counterclockwise to open it.
2.
Dampen a piece of cotton with isopropyl alcohol, and use it to wipe the dust and stains from the sensor.
3.
After the isopropyl alcohol has completely evaporated, close the top cover.
Clearing jammed paper
1.
Turn off the printer and twist the top cover counterclockwise to open it.
2.
Clear and reload the paper.
3.
Close the top cover and restore power to the printer.
Resetting the cutter
1.
Turn off the printer and twist the top cover counterclockwise to open it.
2.
Close the top cover and restore power to the printer to automatically reset the cutter.
3.
Then, clear the paper jam. See
Clearing jammed paper on page 13
.
Cleaning the print head and platen roller 13
6 Interface signal
USB interface
Interface specifications
Table 6-1 USB interface specifications
Parameter
Data transmission
Connector
Interface signal definition and function
Table 6-2 Interface signal definition and function
Pin number Signal name
A4/B4/A9/B9
A7/B7
A6/B6
A1/B1/A12/B12
VBUS
DATA-
DATA+
GND
Interface connector
Specifications
USB 2.0 full-speed protocol
USB Type-C connector (supports USB hub)
Description
Power
Data minus
Data plus
Ground
Table 6-3 Interface pin numbers and signals
Pin number
A1
B12
A2
B11
A3
B10
14 Chapter 6 Interface signal
Signal name
GND
GND
TX1+
RX1+
TX1-
RX1-
Table 6-3 Interface pin numbers and signals (continued)
Pin number
B4
A10
B3
A11
B6
A8
B5
A9
B2
A12
B1
B8
A6
B7
A7
A4
B9
A5
Signal name
VBUS
RX2-
TX2-
RX2+
D+
SBU1
CC2
VBUS
VBUS
VBUS
CC1
D-
D-
SBU2
D+
TX2+
GND
GN
Mode
The USB interface can work in either API mode or Windriver mode. API mode is the manufacturer self-defined mode, which requires you to install the USB driver provided by the manufacturer. Windriver mode is also called class mode and requires only the generic driver. The default setting is API mode. To use the printer with a Linux® computer, switch to class mode.
Cash drawer interface
Electrical specifications
Table 6-4 Electrical specifications
Parameter
Driving voltage
Driving current
Cash drawer status detection signal
Specifications
24 V DC
Maximum 1 A
“L” = 0 V–0.5 V; “H” = 3.3 V
Cash drawer interface 15
Interface connector
The cash drawer connector is an RJ-12 6P connector.
Interface signal definition and function
Table 6-5 Interface signal definition and function
Number Signal name
1
2
3
4
5
6
FG
DRAWER 1
DRSW
VDR
DRAWER 2
GND
Description
Frame ground
Cash drawer 1 driving signal
Cash drawer status detection signal
Cash drawer driving power
Cash drawer 2 driving signal
Circuit share ground
16 Chapter 6 Interface signal
Download
Advertisement
Key features
All-in-One 35.6 cm (14")
Touchscreen
Qualcomm Snapdragon 2.2 GHz
LPDDR3-SDRAM 4 GB
45 W