OPERATING INSTRUCTIONS
Dishwasher DOD651PHXXLS
Technical information
Technical data
Height: 34 1/2 - 35 1/2"
Width:
Depth:
Weight:
24 5/8"
25"
1)
163 lb (74 kg)
2)
Water pressure:
Electrical connection:
Rated power:
4.2
– 140 psi
See serial number plate
See serial number plate
1)
2)
27 1/4" including handle.
Weight can vary due to different specifications.
19
Installation instructions
24 5/8 25
52
2 3/8
['']
20
4 7/8
Important safety instructions
• Connections to electricity, water, and drainage must be performed by a qualified professional.
• Always follow applicable regulations for water, drainage, and electricity.
• Take care during installation! Wear protective gloves! There must always be two people!
• Place a drip tray on the floor beneath the dishwasher to prevent damage from any water leaks.
• Before screwing the dishwasher into place, test the dishwasher by running the Rinse and hold program. Check that the dishwasher fills with water and drains. Also check that none of the connections leak.
WARNING!
Turn off the water supply when installing the dishwasher!
The plug must be disconnected or power to the outlet turned off while installing the dishwasher!
Nominal dimensions. Actual measurements may vary.
Transport protection for the door
Do not forget to remove the transport protection for the door when unpacking the dishwasher.
REMOVE
Operating environment
Do not place this appliance (including the PEX fill hose and drain hose) where it will be hit by direct sunlight or exposed to extreme weather conditions.
Do not place the outdoor dishwasher close to a swimming pool. Water splashing on the machine ’ s surfaces can ultimately lead to corrosion
(rust).
This appliance is designed to operate outdoors. It is set to operate within the ambient temperature limits between 50 °F (10 °C) and 104 °F
(40 °C). These temperature limits should not be exceeded.
Placing the dishwasher
The dishwasher is intended for freestanding installation, but can also be installed under a countertop.
Use caution when the appliance is installed or removed to reduce the likelihood of damage to the power supply cord.
Adjust the height and slide the dishwasher into place
5/8''
1''
Freestanding
1 Make sure the area where the dishwasher will be installed is firm.
Adjust the dishwasher's height using the four adjustable feet to level the unit. The dishwasher may lean no more than 0.2" (5 mm).
2 Lock the steel feet with the lock nuts.
3 Once the feet are properly adjusted, tighten the anti-tip feet firmly against the floor.
Anti-tip feet
Built-in
1 Start by measuring the height from the floor to the bottom edge of the countertop.
2 Measure the height from the floor to the top edge of the dishwasher.
3 Adjust the dishwasher's feet by turning them clockwise to raise or counterclockwise to lower the machine.
4 Verify there is an air gap of at least 1/8'' between the underside of the countertop and the top edge of the dishwasher.
5 Tighten the lock nuts (lock nut) on the rear feet.
6 Slide the dishwasher into place.
• Pull the drain and supply hoses through the opening as the dishwasher is slid into place.
• Check that the hoses have no kinks or sharp bends, and check that there is nothing that can damage the hoses.
7 Make any final adjustments to the front feet (the dishwasher may lean no more than 1/4'') and tighten the lock nuts.
8 Once the feet are properly adjusted, tighten the anti-tip feet firmly against the floor.
21
22
Drain connection
The high loop is necessary for proper draining. Therefore, the dishwasher has the drainage hose attached to the top back of the unit.
This gives the drainage hose an automatic high loop. The drainage hose is fastened at the best high loop height.
High loop
The hose must always discharge at least 13 3/4'' above the bottom of the machine.
min.
1/2''
Connect the drain hose to, for example, the sink's water trap. The connection nipple must have an internal diameter of at least 1/2''. The water trap must be ventilated.
The drain hose may be extended by a maximum of 87" (2.2 m) (the total length of the drain hose must not exceed 177" (4.5 m)). Any joins and connecting pipes must have an internal diameter of at least 1/2''.
However, the drain hose should ideally be replaced with a new hose without joins.
No part of the drain hose may be more than 37 3/8'' above the bottom of the dishwasher.
Attach the drain hose with a hose clamp. Ensure that the drain hose has no kinks.
NOTE!
Do not remove the high loop attached to the back of the dishwasher!
To accommodate a drain on the left side of the dishwasher, remove the drain hose and reverse the direction in the high loop bracket.
Connection to water supply
Use only the inlet hose supplied with the dishwasher. Do not re-use old or other spare hoses.
The supply pipe must be fitted with a water supply valve. The water supply valve must be easily accessible, so that the water can be shut off if the dishwasher has to be moved.
Once the installation is complete, turn on the water supply valve and allow the pressure to settle for a while. Check that all connections are watertight.
Water supply
The machine can be connected to either a cold or a hot (max. 160 °F
(70 °C)) water supply. The water pressure should be 4.2-140 psi.
Connection to cold water supply
Connect the dishwasher to the cold water supply if the building is heated using oil, electricity, or gas.
Connection to hot water supply
Connect the dishwasher to the hot water supply (max. 160 °F (70 °C)) if the building is heated using an energy-efficient means such as district heating, solar power, or geothermal power. Choosing a hot water connection cuts dishwashing times and reduces the dishwasher's energy consumption.
NOTE!
Do not exceed the permitted water supply temperature. Certain materials used in some cookware cannot withstand strong heat. See
Fragile dishes in the chapter Loading the dishwasher.
Electrical connection
Information about the electrical connection can be found on the serial number plate. This specification must match the electricity supply.
The power supply receptacle for the appliance must be installed in a cabinet or on a wall adjacent to the undercounter space in which the appliance is to be installed. Do not use an extension cord for this appliance.
The access hole for the the electrical supplie must be round and smooth and no bigger than 1 1/2'' in diameter. If the partition is metal, it needs to be covered with an edge protector.
Use caution when the appliance is installed or removed to reduce the likelihood of damage to the power supply cord.
Grounding Instructions
This appliance must be grounded. In the event of a malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current. This appliance is equipped with a cord fitted with an equipment grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is installed and grounded in accordance with all local codes and ordinances.
WARNING!
Improper connection of the equipment grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service representative if you are in doubt as to whether the appliance is properly grounded. Do not modify the plug provided with the appliance. If it does not fit the outlet, have an appropriate outlet installed by a qualified electrician.
WARNING!
Risk of electric shock. Do not use an extension cord for this appliance.
Connect dishwasher cord directly to a dedicated outlet suitable for installation in damp or wet locations and protected by a Ground-Fault
Circuit-Interrupter (GFCI) in accordance with local codes. If an outlet is not provided, contact a qualified electrician for proper installation.
