Atdec A F -AT-W Installation Manual

Wall Mounted Monitor Arm

Installation Guide

AF-AT-W

COMPONENT CHECKLIST

A

Arm Assembly

(x1)

E

Primary arm cable cover

(x1)

F

Secondary arm cable cover

(x1)

G

2.5mm

Allen key

(x1)

H

5mm

Allen key

(x1)

B

VESA head

(x1)

C

End Cap

(x1)

D

Wall Plate

(x1)

I

Nylon Anchor

Plug

(x2)

J

Countersunk

Screws

M4 x 12mm

(x2)

K

Countersunk

Screws

M6 x 50mm

(x2)

L

Mounting screws

M4 x 10mm

(x4)

M

Mounting screws

M4 x 12mm

(x4)

N

Mounting screws

M4 x 16mm

(x4)

O

Security Screw

M4 x 16mm

(x1)

REQUIRED TOOLS

• Power Drill

• Drill Bit

• Phillips Head Screwdriver

WEIGHT RANGE

0 - 8kg

(0 - 17.6lbs)

IMPORTANT INFORMATION

! Please ensure this product is installed as per these installation instructions.

! The manufacturer accepts no responsibility for incorrect installation.

AF-AT-W Page 1 of 4

1.

Position Wall Plate

As a guide, it is recommended that the bottom of the

Wall Plate be positioned approximately 140mm (5 1/2”) above the desktop.

Note: The wall-mounted arm provides vertical adjustment of 128mm.

128mm (5”)

140mm (5 1/2”)

2.

Choose the appropriate installation procedure depending on your wall type

Masonry

Nylon

Anchors

Timber Stud

Timber

Stud

8mm (5/16”)

Hole

M6 x 50mm

Countersunk

Screw

5.5mm

(1/4”) Hole

M6 x 50mm

Countersunk

Screw

Wall Plate

3.

Mount Arm Assembly

3.1

Unlock the Locking Dial before inserting the Arm Assembly into the

Wall Plate

Locking Dial

Wall Plate

Wall Plate v

3.2

Slide the Arm Assembly to the preferred height and lock to secure the arm

3.3

Secure the End Cap with the supplied M4x12mm Countersunk

Screws and 2.5mm Allen Key

M4x12mm

Countersunk Screw

End Cap

2.5mm Allen Key

Locking Dial

AF-AT-W Page 2 of 4

4.

Install VESA monitor head

4.1

Install VESA monitor head as shown

100mm

Screen

VESA monitor head

M4x10/12/16mm

Phillips Head Mounting

Screws

Optional Spacers (may be required for recessed and uneven surfaces)

100mm

5.

Mounting Monitor

5.1

Insert VESA monitor head into the receptacle in the Arm Assembly

VESA monitor head

Arm Assembly

5.2

OPTIONAL SECURITY SCREW

Ensure the Monitor is supported, then loosen the Monitor head screw with the 5mm Allen Key and tilt screen up before installing the M4 x 16mm Security Screw into the Security

Screw hole

Note: Support Screen when adjusting tilt.

Monitor head screw

Security Screw

Hole

Loosen

Tighten

Phillips Head

Screwdriver

5mm Allen Key

M4 x 16mm

Security Screw

6.

Adjusting Height

6.1

After plugging in your cables,

install the Cable Covers.

6.2

Lift/Lower Screen to the desired height. Move both Screen and Arm assembly together.

6.3

Lock the Lock Dial firmly.

AF-AT-W Page 3 of 4

7.

Cable Management

7.1

After plugging in your cables, install the Cable Covers.

Insert Cable Covers up into Lock Slots.

Lock Slot

7.2

Push Cable Covers away from Elbow Joint to secure in place.

‘click’

‘click’

Elbow Joint

7.3

Cable Clips and Cable Stops can be installed to further manage cables.

Note: Ensure enough cable slack is given to allow for movement.

8.

Adjusting the Display Bracket

Portrait/ Landscape Tilt (Screen angle up/down) Pan (Screen angle left/right)

No Allen Key necessary

Loosen

Tighten

5mm Allen Key

Note: Support Screen when adjusting tilt.

No Allen Key necessary

No portion of this document or any artwork contained herein should be reproduced in any way without the express written consent of Atdec Pty Ltd. Due to continuing product development, the manufacturer reserves the right to alter specifications without notice. ©20180206B atdec.com | atdec.co.uk | atdec.com.au

AF-AT-W Page 4 of 4