Smart Technologies Document Camera 650 User Guide
Reklama
Reklama
SMART Document Camera 650
USER GUIDE
SDC-650
Was this document helpful?
smarttech.com/docfeedback/171733
Learn more
This guide and other resources for SMART Document camera 650 are available in the
Support section of the SMART website ( smarttech.com/support ). Scan this QR code to view these resources on your mobile device.
FCC warning
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the manufacturer’s instructions, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
Trademark notice
SMART Board, smarttech, the SMART logo and all SMART taglines are trademarks or registered trademarks of SMART Technologies ULC in the U.S. and/or other countries. All thirdparty product and company names may be trademarks of their respective owners.
Copyright notice
© 2021 SMART Technologies ULC. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system or translated into any language in any form by any means without the prior written consent of SMART Technologies ULC. Information in this manual is subject to change without notice and does not represent a commitment on the part of SMART.
This product and/or use thereof is covered by one or more of the following U.S. patents: www.smarttech.com/patents
April 7, 2021 smarttech.com/kb/171733 2
SMART Document Camera 650
Important information
WARNING
l
Failure to follow the installation instructions included with the SMART product could result in injury and product damage which may not be covered by the warranty.
l
Ensure that any cables that cross the floor to the SMART product are properly bundled and marked to avoid a trip hazard.
l
Do not puncture, crush, heat or disassemble the battery, expose it to fire or any liquid, short its terminals, or abuse the battery in any other way as this may cause the battery to explode or ignite, and could cause a fire or injury.
l
Don’t install the battery backwards or reverse the polarity. Don’t install other types of battery in the remote control. Both of these actions can cause damage to the remote control and can cause a fire or injury.
l
To reduce the risk of fire or electric shock, do not expose the SMART product to rain or moisture.
l
Do not push foreign objects into the openings on your
SMART product.
l
Do not open or disassemble the SMART product. You risk electrical shock from the high voltage inside the casing. Opening the casing also voids your warranty.
l
The camera arm on your SMART product has joint that present a pinch hazard when your move the camera arm. Keep clear of the pinch points.
l
Do not stare into the light or shine the light directly into someone’s eyes. Turn off the light when capturing images of people.
l
Do not overload power outlets or extension cords as this can result in a fire or electric shock.
l
Turn off and disconnect your SMART product before a thunderstorm. During a thunderstorm, do not touch your
SMART product or the plug, because there is a risk of electrical shock.
l
Only use your SMART product with the type or power source that is written on the power supply and do not modify the plug.
l
Do not short circuit or allow contract with conductive objects to the battery terminals.
l
Do not disassemble batteries.
CAUTION
l
Place your SMART product on a solid surface to prevent it from falling.
l
If you have a security cable attached to your SMART product, do not carry or swing your SMART product by the security cable.
l
Do not connect non-shielded interface cables to your
SMART product and do no leave cables connected to unused connectors, because this can cause interference level that exceed FCC regulations.
l
Avoid setting up and using the SMART product in an area with excessive levels of dust, humidity and smoke.
l
Do not block or cover the opening or slots on your
SMART product. These slots provide ventilation, ensure reliable operation and protect your SMART product from overheating.
l
Do not carry your SMART product by the camera arm.
Carry it by the base of the unit.
l
Do not aim the camera lens at the sun.
l
If the SMART product requires replacement parts, make sure the service technician uses replacement parts specified by SMART Technologies or parts with the same characteristics as the original.
l
Ensure that batteries are stored in a cool and dry place.
l
Do not discard batteries in water, fire, or domestic waste. Dispose batteries at collection points.
l
Remove the batteries in the remote control if you are not in for an extended period of time. Battery corrosion or leakages can damage the remote control.
l
Do not mix new and used batteries.
l
Do not mix different types of batteries: alkaline, nickelcadmium (rechargeable), or carbon-zine.
Federal Communication Commission
Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
smarttech.com/kb/171733 3
SMART Document Camera 650
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
l
Reorient or relocate the receiving antenna.
l
Increase the separation between the equipment and receiver.
l
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
l
Consult the dealer or an experience radio/TV technician for help.
Ce dispositif est conforme à la norme CNR-210 d’Industrie
Canada applicable aux appareils radio exempts de licence. Son fonctionnement est sujet aux deux conditions suivantes:
1. le dispositif ne doit pas produire de brouillage préjudiciable, et
2. ce dispositif doit accepter tout brouillage reçu, y compris un brouillage susceptible de provoquer un fonctionnement indésirable.
CAUTION
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
For operation within 5.15 ~ 5.25GHz / 5.47 ~5.725GHz frequency range, it is restricted to indoor environment. The band from 5600-5650MHz will be disabled by the software during the manufacturing and cannot be changed by the end user. This device meets all the other requirement specified in
Part 15E, Section 15.407 of the FCC Rules.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20cm between the radiator & your body.
FCC
Supplier’s Declaration of Conformity
47 CFR § 2.1077 Compliance Information
Unique Identifier: SDC-650, WD650
Responsible Party – U.S. Contact Information
SMART Technologies Inc.
2401 4th Ave, 3rd Floor
Seattle,WA 98121 [email protected]
Innovation, Science, and Economic
Development Canada Statement
This device complies with RSS-210 of the Industry Canada Rules.
Operating is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.
CAUTION
i. the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;
ii. the maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725 MHz shall comply with the e.i.r.p. limit; and
iii. the maximum antenna gain permitted for devices in the band 5725-5825 MHz shall comply with the e.i.r.p. limits speci"ed for point-to-point and non point-to-point operation as appropriate.
iv. Users should also be advised that high-power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to
LE-LAN devices.
Avertissement:
i. Le guide d’utilisation des dispositifs pour réseaux locaux doit inclure des instructions précises sur les restrictions susmentionnées, notamment :
ii. les dispositifs fonctionnant dans la bande 5 150-5 250
MHz sont réservés uniquement pour une utilisation à l’intérieur a"n de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux;
iii. le gain maximal d’antenne permis pour les dispositifs utilisant les bandes 5 250-5 350 MHz et 5 470-5 725 MHz doit se conformer à la limite de p.i.r.e.;
iv. le gain maximal d’antenne permis (pour les dispositifs utilisant la bande 5 725-5 825 MHz) doit se conformer à la limite de p.i.r.e. spéci"ée pour l’exploitation point à point et non point à point, selon le cas.
v. De plus, les utilisateurs devraient aussi être avisés que les utilisateurs de radars de haute puissance sont désignés utilisateurs principaux (c.-à-d., qu’ils ont la priorité) pour les bandes 5 250-5 350 MHz et 5 650-5 850 MHz et que ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL.
Radiation Exposure Statement:
This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20 cm between the antenna of this device and all nearby persons.
smarttech.com/kb/171733 4
SMART Document Camera 650
Déclaration d'exposition aux radiations:
Cet équipement est conforme aux limites d’exposition aux rayonnements ISED établies pour un environnement non contrôlé.Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps.
EU Declaration of Conformity
Hereby, SMART Technologies ULC declares that the ratio equipment type Wireless AC Dual Band Adapter, WD650 is an compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: smarttech.com/compliance .
Waste Electrical and Electronic Equipment regulations (WEEE and Battery Directive)
Electrical and electronic equipment and batteries contain substances that can be harmful to the environment and to human health. The crossed-out wheeled bin symbol indicates that products should be disposed of in the appropriate recycling stream and not as regular waste.
Batteries
The SMART Document Camera 650 contains rechargeable lithium-ion batteries. The remote contains two AAA batteries.
Recycle or dispose of batteries properly.
See smarttech.com/compliance for more information.
WARNING
This equipment is compliant with Class A of CISPR 32. In a residential environment, this equipment may cause radio interference.
The frequency band and the maximum transmitted power in EU are listed below:
Transmitting Band
(MHz)
2400-2483.5
5180- 5320
5500-5700
Maximum Transmit Power EIRP
(dBm)
20
19
21
Restrictions in (5GHz)
AT/BE/BG/CZ/DK/EE/FR/DE/IS/IE/IT/EL/ES/CY/LV/LI/LT/LU/HU/M
T/NL/NO/PL/PT/RO/SI/SK/TR/FI/SE/CH/UK/HR. 5150MHz-
5350MHz is for indoor use only.
CAUTION: EXPOSURE TO RADIO FREQUENCY
RADIATION
This equipment complies with EU radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body.
Hardware environmental compliance
SMART Technologies supports global efforts to ensure that electronic equipment is manufactured, sold and disposed of in a safe and environmentally friendly manner.
smarttech.com/kb/171733 5
Contents
Understanding Camera and PC modes
Setting up your document camera
Turning your document camera on and off
Installing software for your document camera
Connecting to a computer or display
Chapter 3: Using your document camera
Using the on-screen display menu
Using Camera mode to display objects and documents
Capturing images and videos to a USB drive
Using a microscope with your document camera
Using Miracast to view images on a display
Chapter 4: Using the SMART Document Camera 650 software
Viewing a document camera’s live image
Using the software to control the live image
Viewing saved images and videos in the library
Chapter 5: Using with SMART Notebook software
Using the Document Camera Viewer in SMART Notebook
smarttech.com/kb/171733
6
Chapter 1:
Chapter 1
Welcome
Understanding Camera and PC modes
Computer Pass-Through (PC) mode
About this guide
This guide is for users who set up and use the SMART Document Camera 650 in their organizations.
It includes information about setting up the document camera and using the document camera’s on-screen display menu and software.
For more information, such as videos, training, and how-to topics, visit support.smarttech.com/docs/redirect/?product=doccamera650 .
smarttech.com/kb/171733 7
Chapter 1
Welcome
Features
The SMART Document Camera 650 connects digital learning to the physical world. This easy-to-use 4K
Ultra HD visualizer captures live video and images directly to the SMART Board® interactive display, SMART
Notebook® software, or your desktop. The SDC-650 is a fully UVC-compliant camera with built-in microphone that can be used as a high-quality webcam with SMART Board displays, keeping the continuity of a classroom experience even while video conferencing.
The document camera includes the following features:
Feature
Camera
Output/input
Physical construction
Software
Image and video storage
Details
l
High resolution CMOS sensor
l
23x digital zoom
l
Up to 60 frames per second
l
Automatic, manual, or area focus
l
Maximum shooting area 17 4/8" × 9 6/8"
l
HDMI 4K, 1080p @ 50 Hz / 60 Hz, 720p @ 50 Hz / 60 Hz
l
USB mini-B (for connecting to a computer)
l
USB 2.0 Type A (with pre-installed Wi-Fi dongle)
l
USB 2.0 Type A (for a USB storage device)
l
Built-in battery
l
Built-in LED illumination lamp
l
Anti-theft slot l
Mechanical arm
l
Integrated microphone in base
l
Supports the following software on a connected Windows or macOS computer:
o
SMART Notebook 20.1 or later collaborative learning software (includes
SMART Ink and Product Drivers)
o
SMART Document Camera 650 software
l
Supports USB storage smarttech.com/kb/171733 8
Chapter 1
Welcome
Components
The SMART Document Camera has a flexible arm for positioning the lens at any angle. The camera head has
LED overhead lighting to enhance lighting conditions.
The SMART Document Camera 650 consists of the following components:
6
7
8
9
2
3
4
5
No.
1
Name
Camera head
LED light
Camera arm
IR sensor
Control panel
Built-in mic
Front panel
Right panel
Handle smarttech.com/kb/171733 9
Chapter 1
Welcome
Control panel
The control panel to enables you to switch among Camera, Computer Pass-Through, and Playback modes.
You can also use the control panel to adjust the settings and features in the Camera mode’s on-screen display (OSD) menu.
The document camera’s control panel consists of the following:
1
No.
2
3
Name
Power/Power indicator
Wi-Fi connection indicator
More information
l
Turn the document camera ON/OFF
l
Power indicator:
o
Solid red: Standby
o
No light: Power off
o
Solid green: Power on
l
Solid blue: P2P / Wi-Fi Mode Ready
l
Slow flashing blue: Camera is connected to the SMART Document Camera software
l
Short flashing blue: Connecting to Wi-Fi
l
Quick flashing green: Scanning for a Miracast device
l
Slow flashing green: Starting Miracast stream
l
Solid green: Connected to a Miracast device
l
Increase or decrease the image magnification in Camera mode
l
Access options from the OSD menu
4
Zoom in/out and
Navigate up/down
Brightness increase/decrease and
Navigate left/right
l
Increase or decrease the level of brightness when capturing a live images
l
Access options from the OSD menu smarttech.com/kb/171733 10
Chapter 1
Welcome
6
7
8
9
10
11
12
No.
5
Name
Auto-Focus / Select
Wi-Fi/USB mode
Record
Freeze
Lamp
Capture
Info
Camera/PC mode
More information
l
Automatically adjust focus
l
Selection option for Playback mode and OSD menu
l
Start or pause video playback
l
Switch between using Wi-Fi or the USB connection mode
l
Start or stop recording video and audio
l
Pause or resume an image frame in Camera mode
l
Turn the overhead light ON/OFF
l
Capture an image in Camera mode
l
Access the on-screen display (OSD) menu
l
Switch the video signal between Camera and Computer Pass-Through (PC) modes
(see Understanding Camera and PC modes on page 15)
Right panel
The right panel of the document camera consists of the following:
1
No.
2
3
Name
HDMI input
HDMI output
DC power jack
More information
l
Use to connect a computer to the document camera
l
Use to connect to an external display (monitor, projector, or interactive display)
l
Use to recharge the document camera’s battery smarttech.com/kb/171733 11
Chapter 1
Welcome
Front panel
2
3
4
5
The front panel of the document camera consists of the following:
1
No.
Name
Battery charge indicator
More information
l
Solid green:
o
Three power bars: battery is fully charged
o
Two power bars: battery is 30 to 60% charged
o
One power bar: battery is 5 to 30% charged
l
Solid red: Battery is 0 to 5% charged
l
Flashing red: Battery is out of power
l
Solid orange: Battery needs servicing; contact SMART support
USB mini port
USB port
Wi-Fi dongle receiver
Anti-theft slot
l
Port for connecting the document camera to a computer using a USB connection
l
Port for a USB flash drive
l
Receiver for the Wi-Fi dongle
l
Attachment for a Kensington compatible lock smarttech.com/kb/171733 12
Chapter 1
Welcome
Remote control
All features of the SMART Document Camera 650 can be accessed with the remote control. The remote control requires two AAA batteries.
5
6
No.
1
2
3
4
Name
Power
WiFi/USB
Mute
Camera/PC mode
Capture
Record
More information
l
Turn the document camera ON/OFF
l
Switch between Wi-Fi and USB connection mode
l
Mute the volume
l
l
Capture still image in Camera mode. When in continuous capture mode, press this button again to stop.
l
Start or stop recording video and audio
NOTE
Video recording can be saved to a connected USB drive or a connected computer only when using SMART Notebook or SMART Document Camera 650 software.
smarttech.com/kb/171733 13
Chapter 1
Welcome
No.
7
8
9
20
21
22
13
14
15
10
11
12
18
19
16
17
Name
Resolution
Freeze
Auto-Exposure lock
Lamp
Rotate
Mode
Delete
Info
Select
Navigate
Auto-focus
Zoom In/Out
Volume
Brightness
Zoom 1X
Reset
More information
l
Press to switch among the following modes:
o
Auto detect
o
1024 × 768 (if the HDMI device supports it)
o
K 60Hz (if the HDMI device supports it)
l
Pause or resume an image frame in Camera mode
l
Lock the exposure to stop the document camera from adjusting the exposure automatically
l
Turn the overhead light ON/OFF
l
Rotate an image in Camera mode
l
Switch among Normal, High frame, High quality, Microscope, Infinity, or Macro modes.
l
Delete image or video in Playback mode
l
Press to view system information and battery status
l
Press to make a selection
l
Navigate through the on-screen display menu (OSD)
l
Automatically adjust focus
l
Increase or decrease the image magnification on camera and picture Camera mode
l
Adjust the volume
l
Increase or decrease the brightness when capturing live images
l
Reset to default zoom magnification (100%)
l
Reset to factory default settings
Power adapter
Your document camera comes with a power adapter, including a country specific power cord (for EU, UK, and North America) that connects to the external power supply.
USB cable
Use the USB cable to connect your document camera to your computer. You can display objects, capture images to SMART Notebook files, and control your document camera from SMART Notebook software.
If you need to extend the USB connection, see the Troubleshooting and extending USB 2.0 and USB 3.0 connection knowledge base article for guidance.
Wi-Fi dongle
Use the Wi-Fi dongle to connect your document camera to the network.
See Using the HDMI method to connect on page 22.
smarttech.com/kb/171733 14
Chapter 1
Welcome
Understanding Camera and PC modes
You can use your document camera in Camera or Computer Pass-Through (PC) mode. Each mode enables you to do different things and requires a specific connection to a display, projector, or computer.
Camera mode
In Camera mode, you can view live images captured by the document camera:
l
In SMART Notebook software using the USB connection
l
In SMART Document Camera software using the USB or WiFI connection
l
On a display or projector using the HDMI out connection
or Miracast (if the display or projector supports
it)
Computer Pass-Through (PC) mode
PC mode enables you to view your computer’s desktop on a connected display or projector. In this mode, the document camera acts as a pass-through device between the computer and the display or projector.
To use this mode, connect an HDMI cable to your computer and then to the HDMI IN port on the document camera, then connect a second HDMI cable from the document camera’s HDMI OUT port to a display or projector.
NOTES
l
The Capture button on the document camera’s control panel has no effect in PC mode.
l
In PC mode, you can view the document camera live image only in SMART Notebook software.
smarttech.com/kb/171733 15
Chapter 1
Welcome
Features of each mode
The following table describes the differences between each mode.
Feature
View computer input
View document camera image
Control the document camera from a computer
Capture to SMART Notebook software
Access the related on-screen display menu
Capture to a USB drive
Camera mode
No
Yes
Yes
Yes
Yes
Yes
No
No
No
PC mode
Yes
No
No smarttech.com/kb/171733 16
Chapter 2:
Chapter 2
Getting started
Setting up your document camera
Turning your document camera on and off
Installing software for your document camera
Connecting to a computer or display
Using the USB method to connect
Using the HDMI method to connect
Using the P2P method to connect
Connecting your document camera to Miracast
Setting up your document camera
Before you use the SMART Document Camera, unfold and position it, then connect it to power to fully
After the software’s installed, you can connect the document camera to that device .
To unfold and position your document camera
1. Hold the handle of the document camera to stabilize it.
2. Lift the camera arm up, then pull the camera arm outward.
3. Rotate the camera head and aim the lens at your object.
smarttech.com/kb/171733 17
Chapter 2
Getting started
To connect your document camera to the power supply and charge the battery
1. Connect the provided power supply cable to the DC port on the right connection panel.
NOTE
Before you use the camera for the first time, charge the battery fully. The battery charge indicator on the front panel shows you the battery’s status. For more information about the battery charge
indicator, see Battery charge indicator on page 12.
2. Connect the power supply cable to a power outlet.
After the power is connected, the document camera enters Standby mode and starts charging.
Turning your document camera on and off
After you’ve completed the basic connections, you are ready to turn the document camera on for the first time.
To turn on your document camera
Press on the control panel or the remote control until the power indicator light turns green.
To turn off your document camera
Press on the control panel or remote control for three seconds.
The power indicator light turns off.
NOTE
If you press and hold the power button for less than three seconds, the document camera enters
Standby mode and the power indicator light shines solid red.
smarttech.com/kb/171733 18
Chapter 2
Getting started
Installing software for your document camera
Before you use your document camera, download the required software to get the most out of your document camera. Download and install the latest version of the following software before you connect your document camera to a device:
Software
SMART Notebook 20.1 or later (includes
SMART Ink and Product Drivers)
Supported operating systems or devices
l
Windows computer
l
Mac computer
SMART Document Camera software
NOTE
Refer to SMART Notebook’s computer requirements for complete system requirements.
l
Windows
l macOS
l
Android (including the iQ experience on
SMART Board interactive displays)
To access downloads and installation instructions for the software on Windows and Mac operating systems, see support.smarttech.com//docs/redirect/?product=doccamera650&context=downloads .
The SMART Document Camera 650 Android app for SMART Board interactive displays with iQ is available from the iQ app store or from the Google Play store for other Android devices.
smarttech.com/kb/171733 19
Chapter 2
Getting started
Connecting to a computer or display
There are a number of ways to connect your SMART Document Camera to a display device, such as a computer or SMART Board interactive display:
Method
USB Out
Description
Use this method if you will be using the document camera with a computer or a
SMART Board interactive display with iQ.
NOTE
This method is required if you plan to use the document camera with SMART Notebook software.
HDMI Out Use this method to connect directly to a display that has an HDMI port, such as a
SMART Board interactive display.
Wireless Use this method to connect to a Wi-Fi-enabled device, such as a computer or SMART Board interactive display, from anywhere in the classroom. There are three wireless connection methods:
l
Peer-to-Peer (P2P) (recommended)
l
Wi-Fi
l
Miracast
Read the sections below for the connection method you want to use.
IMPORTANT
Before completing these procedures, make sure you install the required software .
smarttech.com/kb/171733 20
Chapter 2
Getting started
Using the USB method to connect
Use the included USB cable to connect the document camera to a computer.
To connect your document camera to a computer with a USB cable
1. Use the included USB cable to connect the USB B port on the document camera to a USB port on the computer:
TIP
If you need to extend the USB connection, see Troubleshooting and extending USB 2.0 and USB 3.0 connection .
2. Press on the control panel until the Wi-Fi indicator light is off.
3. Turn the document camera on and then press Camera/PC on the control panel or remote control.
4. Open the SMART Document camera software or SMART Notebook software, depending on which application you want to use to display the document camera’s live images.
smarttech.com/kb/171733 21
Chapter 2
Getting started
Using the HDMI method to connect
Use the HDMI Out port to connect the document camera to a display. Using this method only displays the document camera’s live image on the connected display device. Use the remote control or control panel to change the picture (for example, zoom in, focus, freeze, and so on). If you want to record video or save captures of the live image, first attach a USB drive to the document camera.
To connect your document camera to a display device
1. Connect the HDMI cable to the HDMI OUT port on the document camera’s rear connection panel.
2. Locate the HDMI IN port on the display device and connect the HDMI cable.
3. Press the Camera/PC button on the control panel or remote control to switch the video signal to the display device.
Using the P2P method to connect
You can use the included Wi-Fi dongle to create a direct Peer-to-Peer (P2P) wireless connection between the document camera and your computer. This direct connection enables you to quickly connect the document camera without having to enter a password to connect school’s network.
This is the easiest and recommended way to connect wirelessly.
smarttech.com/kb/171733 22
Chapter 2
Getting started
NOTES
l
If you connect using P2P, the document camera’s built-in mic cannot be used to record sound.
Instead, you must use the mic on the device you are connecting to for recording sound.
l
SMART Notebook software cannot be used with this connection method. To use the document
camera with SMART Notebook, use a USB connection .
To connect using P2P
1. Download and install the SMART Document Camera software
.
IMPORTANT
For macOS, this download includes a driver for the Wi-Fi dongle that must be installed separately on the computer.
2. Connect the included Wi-Fi dongle to a USB port on your computer.
3. Open the SMART Document Camera software.
You will see your document camera listed.
TIP
Check the serial number on the bottom of the camera to find the camera name.
4. Click .
5. Click Next .
smarttech.com/kb/171733 23
Chapter 2
Getting started
6. (Optional) Enter a name and password for the document camera. A name helps you identify the document camera more easily, while the password will prevent unwanted users from connecting to your document camera wirelessly. If no name is entered, a default name is used.
TIP
You can change the name and password later by selecting the Info button for the document camera.
7. Click Done .
The connection should be complete in about 60 seconds. When connection is successful, the camera’s live image appears in the SMART Document Camera software.
To learn more about using the SMART Document Camera software’s controls, see page 39.
Using the Wi-Fi connection
The document camera has its own Wi-Fi which you can connect to directly from your device.
To connect your document camera to a wireless network
1. Download and install the SMART Document Camera software
.
2. Press on the control panel.
The Wi-Fi indicator light turns blue.
3. Open the SMART Document Camera software.
The software automatically detects available document cameras.
4. Click for the document camera you want to connect with.
A message appears asking if you want to set up Wi-Fi mode.
smarttech.com/kb/171733 24
Chapter 2
Getting started
5. Click Yes .
You are prompted to select a Wi-Fi network to connect with.
6. Select the network you want to use and enter its password.
7. Click Connect .
8. (Optional) Enter a name and password for the document camera. A name helps you identify the document camera more easily, while the password will prevent unwanted users from connecting to your document camera wirelessly. If no name is entered, a default name is used.
TIP
You can change the name and password later by selecting the Info button for the document camera.
9. Click Done .
10. After the document camera is connected, click .
The camera’s live image appears in the SMART Document Camera software.
To learn more about using the SMART Document Camera software’s controls, see page 39.
Connecting your document camera to Miracast
If your computer or device you want to connect to supports Miracast, you can also set that up to quickly display images captured by the document camera to the device.
To connect your document camera to Miracast
1. Press Info on the control panel or remote control.
The on-screen (OSD) menu appears on your display.
2. Use the right arrow button on the remote control or
Wireless tab.
on the control panel to browse to the
NOTE
If the Wireless tab is disabled, the Wi-Fi mode is turned off. To turn it on, press the Wi-Fi button and wait for the indicator light on the document camera to turn blue.
3. Browse to Mode and then press .
smarttech.com/kb/171733 25
Chapter 2
Getting started
4. Select Miracast and then press .
The Miracast setup option is now available.
5. Use the down arrow button on the remote control or
Miracast Setup and then press .
on the control panel to browse to
6. Select your remote display from the list.
The camera’s image appears on the remote display’s screen after connecting.
smarttech.com/kb/171733 26
Chapter 3:
Chapter 3
Using your document camera
Using the on-screen display menu
Browsing to the OSD menus and sub-menus in Camera mode
Using Camera mode to display objects and documents
Rotating and mirroring the image
Changing the picture mode or adding an effect
Capturing images and videos to a USB drive
Using a microscope with your document camera
Connecting your document camera to a microscope
Using Miracast to view images on a display
Using the on-screen display menu
Use the on-screen display (OSD) menu to adjust settings for your document camera in Camera mode.
The OSD has the following options:
Tab
Image
Wireless
Options
The Image tab contains options for adjusting these live image settings:
l
Brightness
l
Contrast
l
Saturation
l
Preview Mode
l
Effect
l
Mirror
l
Exposure
l
White balance
The Wireless tab contains options for setting the wireless connection, such as AP, Wi-Fi, or Miracast.
smarttech.com/kb/171733 27
Chapter 3
Using your document camera
Tab
System
Options
The System tab contains a variety of system settings and information, including:
l
Language setting
l
Output Display resolution setting
l
Flicker (refresh rate) settings
l
Information about the document camera (such as model, software version, and so on)
l
Reset to factory default
Browsing to the OSD menus and sub-menus in Camera mode
Press Info on the control panel or remote control to open the OSD menu. After the OSD menu is open, use the following controls on the remote control or control panel to navigate and make selections:
Press Info on the control panel or remote control to exit the OSD menu.
Accessing the Image menu
1. Set your document camera to Camera mode.
2. Press Info on the control panel or remote control.
The OSD menu appears.
3. Browse to and select the Image tab.
smarttech.com/kb/171733 28
Chapter 3
Using your document camera
4. Select the setting you want to adjust:
Image setting options
Brightness
Contrast
Preview Mode
Effect
Mirror
Exposure Setup
White Balance Setup
Description
Adjust the image brightness level manually.
Adjust the image contrast level manually.
Select a mode to use for displaying the live image from the camera:
o
Normal : This is the default mode. In most cases, Normal mode provides the best sharpness and color.
o
Motion : Increases the frame rate to make movement in the live image smoother.
o
High Quality : Provides the best image quality for your chosen shooting area and connected display.
o
Microscope : For use when using the microscope adapter with the document camera.
o
Macro : For use while capturing objects is 4" (10 cm) or less away from the document camera.
o
Infinity : For use while capturing objects that are more than 30" (80 cm) away from the document camera.
Convert the image to color, black/white, or film negative.
Select to flip the image:
o
ON – displays a mirrored image.
o
OFF – displays a normal image.
Select the exposure settings:
o
AUTO – automatically adjust the camera exposure.
o
MANUAL – manually adjust the camera exposure. When you select this option, the Manual Exposure setting becomes available. Select it to manually adjust the exposure.
Select the White Balance settings for various light conditions:
o
AUTO – automatically adjust the white balance.
o
MANUAL – manually adjust the red and blue color levels. When you select this option, the Manual White Balance Blue and Manual White Balance Red options become available for you to adjust.
Accessing the Wireless menu
1. Set your document camera to Camera mode.
2. Press Info on the control panel or remote control.
The OSD menu appears.
smarttech.com/kb/171733 29
Chapter 3
Using your document camera
3. Press the button on the control panel or remote control to browse to the Wi-Fi tab.
Wireless setting options
Mode
Miracast Setup
Description
Choose a wireless mode to use for connecting the document camera to a computer or display. Options are:
o
AP
o
Wi-Fi
TIP
The Wi-Fi option may appear disabled unless you have set up a
o
Miracast
If you enable Miracast mode, select the device you want to connect to from this menu.
Accessing the System menu
1. Set your document camera to Camera mode.
2. Press the Info button on the control panel or remote control.
The OSD menu appears.
3. Press the button on the control panel or remote control to browse to the System tab.
System setting options
Language
Description
Select or change the language.
smarttech.com/kb/171733 30
Chapter 3
Using your document camera
System setting options
Output Display
Flicker
Information
Default
Description
o
Set the resolution to display an image on the screen:
o
1024 × 768
o
1280 × 720
o
1280 × 800
o
1280 × 1024
o
1600 × 1200
o
1920 × 1080
o
Select TV System to switch between NTSC and PAL video systems.
NOTE
This selection is disabled in TV output mode.
Select refresh rate:
o
50 Hz
o
60 Hz
Display the product information.
Restore all the settings to the factory default settings.
Using Camera mode to display objects and documents
When your document camera is connected to a projector, interactive display, or TV, you can display a fullscreen image from your document camera. You can also access features and settings in the on-screen display (OSD) menu.
IMPORTANT
Your document camera must be connected to a display to use the OSD menu.
Using Camera mode
1. Connect your document camera to a projector or flat-panel display with an HDMI cable.
2. Press Camera/PC on the control panel or remote control.
The camera’s image appears on the display.
smarttech.com/kb/171733 31
Chapter 3
Using your document camera
Displaying printed documents
When you set your document camera to Camera mode, you can display documents.
TIP
Use the anti-glare sheet to reduce glare and optimize image quality. The anti-glare sheet is a special coated film that helps eliminate the glare you might encounter while displaying glossy objects, such as magazines and photos. Place the anti-glare sheet on top of an object to reduce reflected light.
To display documents
1. Place your documents on the table.
2. Adjust the document camera, and then aim its lens at your documents.
TIP
To change the orientation of the lens, twist the control on the camera head.
3. Press Auto Focus on the control panel or remote control to adjust the focus.
Displaying objects
1. Press Camera/PC on the control panel or remote control.
2. Place the object, such as a document or a model, you want to display under the camera.
3. Rotate the camera head to aim the lens at your object.
4. If the image is too dark, press Lamp on the control panel or remote control.
Rotating and mirroring the image
To rotate the image
Adjust the camera head to the desired shooting area, and press Rotate on the remote control to rotate the image 180° or twist the control on the camera’s head to rotate the image 90°.
smarttech.com/kb/171733 32
Chapter 3
Using your document camera
To mirror the image
1. Press Info on the control panel or remote control to open the OSD menu.
2. Select Image .
3. Browse to and select MIRROR .
4. Select ON .
5. Press Info again to exit the OSD menu.
Changing the picture mode or adding an effect
Using the remote control or OSD menu, you can change the image mode used to capture the object or document. You can also use the OSD menu to add an effect, such as switching the image to black and white or negative.
To change the picture mode
1. Press Mode on the remote control to switch between picture modes.
OR
Press Info on the control panel or remote control to open the OSD menu, select Image > Preview
Mode , and then select the mode you want.
Both methods provide the following options for image mode:
o
Normal : This is the default mode. In most cases, Normal mode provides the best sharpness and color.
o
Motion : Increases the frame rate to make movement in the live image smoother.
o
High Quality : Provides the best image quality for your chosen shooting area and connected display.
o
Microscope : For use when using the microscope adapter with the document camera.
o
Macro : For use while capturing objects is 4" (10 cm) or less away from the document camera.
o
Infinity : For use while capturing objects that are more than 30" (80 cm) away from the document camera.
smarttech.com/kb/171733 33
Chapter 3
Using your document camera
To add an effect
1. Press Info on the control panel or remote control to open the OSD menu, navigate to Image >
Effect , and then select the effect you want to add:
o
Color
o
B/W (Black and white)
o
Film negative
2. Press Info again to exit the OSD menu.
Capturing images and videos to a USB drive
Use the USB port on the SMART Document Camera to save images and videos to a USB drive. To do this,
set your document camera to Camera mode
and connect a USB drive to the document camera.
TIP
You can also capture images and videos to your computer using SMART Notebook
.
Then, using the remote control or document camera’s control panel, press the Capture button to save an image, or press the or Record button to start recording video. Press the Record button again to stop recording. When you are ready to view the files, connect the USB drive to a computer or interactive display.
smarttech.com/kb/171733 34
Chapter 3
Using your document camera
Using a microscope with your document camera
Connect your document camera to a microscope to examine microscopic objects on a bigger screen.
Connecting your document camera to a microscope
1. Select the appropriate rubber coupler size for the microscope eyepiece and insert it in the microscope adapter.
2. Attach the microscope adapter to the document camera and tighten the three bolts until the adapter is secured.
IMPORTANT
Make sure the arrow on the camera head and microscope adapter are on the same side. smarttech.com/kb/171733 35
Chapter 3
Using your document camera
3. Attach the microscope adapter to the microscope's eyepiece and then connect the document camera to the microscope.
4. Turn the microscope adapter counterclockwise to line up the arrows and lock the microscope adapter in place.
To optimize microscope images
1. Press Info on the control panel or remote control to open the on-screen display (OSD) menu.
2. Select the Image tab.
3. Browse to the Preview Mode sub-menu and press .
4. Select Microscope and press .
5. Adjust and aim the camera head at the furthest point, and then press the AUTO FOCUS button on the control panel or remote control.
6. Adjust the microscope’s focus as needed.
Displaying a microscope slide
1. Place a slide or object on the stage of the microscope.
2. Focus the microscope so that the subject is sharp.
smarttech.com/kb/171733 36
Chapter 3
Using your document camera
3. Position the microscope under your document camera so the camera lens is aligned with the microscope eyepiece.
CAUTION
Ensure you do not hit your document camera lens with the microscope. This could damage your document camera’s lens.
4. Press the CAMERA/PC button on the control panel or remote control so that the document camera is in Camera mode.
5. Press Info on the control panel or remote control to open the on-screen display (OSD) menu.
6. Select the Image tab.
7. Navigate to the Preview Mode sub-menu, and press .
8. Select Microscope and press .
Using Miracast to view images on a display
If you’re using a display that supports Miracast, you can use Miracast to wirelessly share the images captured by the SMART Document Camera 650 to the display.
To use Miracast to share live images from the document camera
1. Press Info on the control panel or remote control.
The on-screen (OSD) menu appears on your display.
2. Use the right arrow button on the remote control or
Wireless tab.
on the control panel to browse to the
NOTE
If the Wireless tab is disabled, the Wi-Fi mode is turned off. To turn it on, press the Wi-Fi button and wait for the indicator light on the document camera to turn blue.
3. Browse to Mode and then press .
4. Select Miracast and then press .
The Miracast setup option is now available.
5. Use the down arrow button on the remote control or
Miracast Setup and then press .
on the control panel to browse to smarttech.com/kb/171733 37
Chapter 3
Using your document camera
6. Select your remote display from the list.
The camera’s image appears on the remote display’s screen after connecting.
smarttech.com/kb/171733 38
Chapter 4:
Chapter 4
Using the SMART Document Camera
650 software
Viewing a document camera’s live image
Using the software to control the live image
Viewing saved images and videos in the library
Adding images or videos to your library from other sources (Windows only)
You can use the SMART Document Camera software to view live images from the document camera to a
device connected through a USB or wireless connection
. When you first open the SMART Document
Camera 650 software, you will see the following main window with the following features: smarttech.com/kb/171733 39
Chapter 4
Using the SMART Document Camera 650 software
Downloading the software
To download the software for Windows and Mac operating systems, visit support.smarttech.com//docs/redirect/?product=doccamera650&context=downloads .
For SMART Board interactive displays with iQ, visit the iQ app store on the display to download the software for Android.
Viewing a document camera’s live image
When you open the SMART Document Camera 650 software, you will see the available cameras you can connect to. If there are multiple cameras are listed, you can filter the list or add a document camera to your favorites. smarttech.com/kb/171733 40
Chapter 4
Using the SMART Document Camera 650 software
To connect to an available camera
1. Open the SMART Document Camera 650 software.
2. Find the document camera you want to connect to and select .
TIPS
o
If you use the document camera often, select to save it to your favorites list for quicker connection in the future.
o
Select Filter and select In my classroom to view a local list of available wireless cameras.
NOTE
If you are trying to connect to a wireless camera, you may need to select before you can start viewing the live image.
The live stream window opens, showing the live image from the document camera.
To add and connect to a document camera manually using its IP address
1.
Open the On-screen display menu for the document camera.
2. Navigate to the System > Information tab to find the IP address.
smarttech.com/kb/171733 41
Chapter 4
Using the SMART Document Camera 650 software
3. In the SMART Document Camera 650 software, select Add Camera .
The Add Document Camera dialog box opens.
4. Enter the document camera’s IP address and select Next .
When the connection is successful, the Save Camera screen appears.
5. (Optional) Enter a name and password for the document camera. A name helps you identify the document camera more easily, and the password will prevent unwanted users from connecting to your document camera wirelessly. If you don’t enter a name, the document camera’s serial number is used.
6. Click Done .
Using the software to control the live image
When you view the live image from a connected document camera, the following controls appear: smarttech.com/kb/171733 42
Chapter 4
Using the SMART Document Camera 650 software
3
4
5
No.
Description
1
2
Closes the live image viewer.
Freezes the document camera’s live image. Select again to unfreeze.
Opens the drawing tools to annotate over the live image.
Takes a screen capture of the entire live image.
Opens the video recording tools:
6
l
Select the microphone to mute or unmute the microphone.
l
Select Record to begin the recording.
l
Select the pause button to pause the recording.
l
Select Stop to end the recording.
Takes a screen capture of a selected section of the live image.
smarttech.com/kb/171733 43
Chapter 4
Using the SMART Document Camera 650 software
No.
Description
7 Opens the focus controls:
8 Enters split-screen mode to view images side-by-side with the document camera’s live image.
Click Add File to browse to an image saved on your device and add it to your split-screen bar at the bottom of the window:
Then select the images you want to view alongside the live image, then click the check mark.
9
To stop split-screen mode, clear the selection of all the images you previously selected, then click the check mark to apply the changes.
Click the X in the split-screen bar to close it.
Rotates the live image.
smarttech.com/kb/171733 44
Chapter 4
Using the SMART Document Camera 650 software
No.
Description
10 Accesses the zoom and panning controls:
11 Opens the document camera’s settings. .
Changing settings
From the settings menu, you can change settings for the camera, display, recordings, and network usage options.
Tab
Camera
Display
Record
Settings
Adjust resolution and the document camera’s image mode and image frequency.
Select the tools you want to appear in the toolbar, such as Freeze, Annotate, Screen shot, and so on.
Choose settings for video recording and screen captures, such as:
l video format and quality
l location for saved video and image files on your device
l microphone settings
l image file format
Advanced Adjust the usage rate for network bandwidth.
Viewing saved images and videos in the library
Recordings or screen captures you take using the SMART Document Camera 650 software are saved to the
Library, which is synchronized with your device’s local drive. To view saved images and videos, open the
Library tab. Then select either the Image or Video folder to see saved files.
smarttech.com/kb/171733 45
Chapter 4
Using the SMART Document Camera 650 software
TIP
Saved files and videos can be used during split screen mode to show side-by-side with the live image.
Adding images or videos to your library from other sources (Windows only)
When using the SMART Document Camera 650 software on a Windows computer, you can add and export images and videos in the software’s library.
To add images or videos on a Windows computer
1. Open Windows’ File Explorer .
2. For images, browse to Pictures > SMART Document Camera 650 software .
OR
For videos, browse to Videos > SMART Document Camera 650 software .
3. Copy the files you want to a new location.
To export images or videos on a Windows computer
1. Open Windows’ File Explorer .
2. For images, browse to Pictures > SMART Document Camera 650 software .
OR
For videos, browse to Videos > SMART Document Camera 650 software .
3. Copy the files you want to a new location.
smarttech.com/kb/171733 46
Chapter 5:
Chapter 5
Using with SMART Notebook software
Using the Document Camera Viewer in SMART Notebook
Use SMART Notebook software to save images and then present them later. If your computer is connected to an interactive whiteboard, projector, or television, you can deliver your SMART Notebook presentation with live images from your document camera.
Connecting to SMART Notebook
The document camera is compatible only with SMART Notebook software using the USB connection mode.
To connect to the computer and turn on USB connection mode
1. Connect the document camera to the computer using the included USB cable.
2. Turn the document camera on and then press Camera/PC on the control panel or remote control.
3. On the computer, open SMART Notebook.
smarttech.com/kb/171733 47
Chapter 5
Using with SMART Notebook software
4. From the Notebook menu, select Insert > SMART Document Camera Viewer .
OR
If you are using the 4K Notebook presenter, select View > 4K presenter > Insert > SMART Document
Camera Viewer .
The SMART Document Camera Viewer window opens in the Notebook page:
The regular SMART Document Camera Viewer window in SMART Notebook:
The SMART Document Camera Viewer window in 4K presenter:
NOTE
The 4K presenter is recommended to use when you are connected to a 4K display device so that you ensure the best picture quality. Otherwise, the controls and features are the same.
smarttech.com/kb/171733 48
Chapter 5
Using with SMART Notebook software
Using the Document Camera Viewer in
SMART Notebook
The SMART Document Camera viewer includes the following controls and features:
3
4
5
No.
Description
1 This area shows the document camera’s live image.
2 There are three image capture controls:
l
Capture and Close: Use this to capture the current live image and insert it on the current
SMART Notebook page. This will also close the SMART Document Camera viewer.
l
Capture to New Page: Use this to capture the current live image and insert it on a new
SMART Notebook page.
l
Capture with Time-Lapse: Use this to capture a time-lapse of the document camera’s live image. You can choose a duration for the time-lapse recording.
NOTE
If you press the Capture button on the document camera’s control panel or remote control, it saves the live image to the SMART Notebook page and closes the SMART Document Camera viewer. Pressing the Capture button again re-opens the SMART Document Camera viewer.
Use these controls to zoom in or out on the live image.
Use these controls to increase or decrease the brightness of the live image.
Use these controls to adjust the focus. You can select Auto-Focus, Focus Out, and Focus In.
smarttech.com/kb/171733 49
Chapter 5
Using with SMART Notebook software
No.
Description
6 Select this control to view the following additional settings for changing the live image’s appearance:
l
Rotate 180°
l
Convert to color
l
Convert to black and white l
Convert to negative
l
Convert to positive smarttech.com/kb/171733 50
SMART TECHNOLOGIES smarttech.com/support smarttech.com/contactsupport smarttech.com/kb/171733
Preuzimanje
Javni link je ažuriran
Javni link do vašeg ćaskanja je ažuriran. You may view and manage your chat links after registration here.
Javni link dokumenta
Reklama
