www.BEAinc.com
BEA ARCHITECTURAL SPECIFICATION SHEET
Automatic Door Solutions: Push Plate – LPR36 Vertical Actuator Bar
(Wireless)
Product Specifications
Vertical actuation bar shall be a UL listed assembly that utilizes 4 redundant membrane switches and provide greater than 200 square inches of activation area. Push Plate for sliding, swinging, folding and revolving doors.
Device shall not require a force to activate that is greater than 2 pounds of pressure, and shall not have horizontal movement greater than 3/16 in. (.47 cm) along the vertical plane.
1. 6 in. (15.24 cm) wide by 36 in. (91.44 cm) high activation area. Capable of being activated from any angle
2. Faceplate shall be constructed of 304-grade stainless steel and covered with a clear, fingerprint resistant powder coat.
3. Backplate shall be constructed of 1/8” (.31 cm) thick extruded aluminum
4. 900MHz or 433MHz transmitter to be pre-wired at the factory and housed within an
ABS end cap.
5. Thermal Range Requirements: Provide touch-activation device that can be used in all climates, allow for thermal range from - 32°F (-35°C) to 212°F (100°C).
6. Vertical Actuation Bar shall have flat face to allow activation of the entire assembly width. Vertical edges to be tapered with friction-fit to be weather resistant and prevent impact from objects and vandalism.
7. Low voltage membrane switch: 100 milliamps, .1 to 50 VDC, 1 Watt
Model 10LPR36-433 – Hardwired only, marked with two (2) Handicapped Logos and PUSH
TO OPEN
Model 10LPR36L-433 – Hardwired, (2) large handicapped only
Model 10LPR36-900
– Hardwired only, marked with two (2) Handicapped Logos and PUSH
TO OPEN
Model 10LPR36L-900 – Hardwired, (2) large handicapped only
Note To Specifier: Product to be specified with one (1) 433 or 900 MHz receiver per door operator. Product included factory installed wireless transmitter of desired frequency.
BEA Inc.
RIDC Park West
100 Enterprise Drive
Pittsburgh, PA 15275-1213
Phone: 1.800.52v3.2462
Fax: 1.888.523.2462
79.0252.01 20151203
Product image and Application Photo
www.BEAinc.com
Technical Specs:
Switch Traces FR4 Gold Plated
Membrane
Switches
3M 7993MP
Base Plate Aluminum
Technical Specs: Hard wired
Contact
Configuration
SPST N.O.
Switching Voltage .1 to 50 VDC
Switching
Capacity
1 Watt
Switching Current .005 to 100 mA DC
Contact Bounce
< .3 ms make;
< .6 ms break
BEA Inc.
RIDC Park West
100 Enterprise Drive
Pittsburgh, PA 15275-1213
Phone: 1.800.52v3.2462
Fax: 1.888.523.2462
79.0252.01 20151203
Faceplate Stainless Steel
Switch Actuator Nylon 6/6
End Cap UL94 ABS
Trip Force
Two Conductor
Cabling
Operation
Temperature
Contact Life
Transmitter
Frequency
1.5 lbs
24 awg
7 x 32 stranding UL 1007
-32º F to 212º F
-35º C to 100º C
2 million cycles
300, 433 or 900 MHz
www.BEAinc.com
900 MHz Tech Specs
900 MHz Wireless Receiver 900 MHz Wireless Transmitters
Frequency Range 908 – 918 MHz
Channels
3 channels, frequency hopping
Digital Modulation
Data Rate
Capacity
Signaling
Frequency Shift Key
Programmable
Capable of 74 unique transmitters
Frequency Range 908 – 918 MHz
Channels
Activation
Buttons
3 channels, frequency hopping
Hardwired: 1
Range
Power
Wireless: 1, 2, 3, or 4
Hardwired: Signal strength may vary per application.
Contact technical services for more information.
Wireless: < 500 feet
–
Open Air
Hardwired: 2 AAA batteries
@ 3 VDC
Wireless: 1 Lithium Ion coin battery @ 3 VDC
Signaling 1 LED, Transmit
Sync Management
Certifications
RF Antenna
Receiver Power
Contact Relays
2 LEDs, learn and activation
1 LED, range finding signal strength smart
LED
FCC Part 15, IC
1/2 wavelength external RF antenna
12 - 24 V AC/DC
1 relay
Battery Life
Certifications
Operating
Temperature
Power
Consumption
Emitted Radio
Power
300,000 activations
FCC Part 15, IC
14°F (-10°C) to 131° F
(55°C)
30 mA
-25 dBm
Maximum Switch
Power
Power
Consumption
Dip Switches
120 VAC @ 0.5 amp
60 VDC @ 0.3 amp
40 mA 24 VDC @ 1 amp
3 dip switches
BEA Inc.
RIDC Park West
100 Enterprise Drive
Pittsburgh, PA 15275-1213
Phone: 1.800.52v3.2462
Fax: 1.888.523.2462
79.0252.01 20151203
Behavior Settings
Learn, Delay,
Activation, Hold time
Potentiometer 0 to 30 second delay
433 MHz Wireless Technical Specs:
Frequency 433 MHz
Radio Control
Type
Digital
Emitted Radio
Power
Power
Consumption
Input Voltage
−28.7 dBm (transmitter)
3 mA (transmitter); 30 mA (receiver)
12 to 24 VAC / VDC
Contact Rating
1.0 A @ 30 VDC
0.5 A @ 125 VAC
0.3 A @ 60 VDC
Operating Temp
Operating Temp
(cont.)
14ºF to 131ºF
-10ºC to 55ºC
Max. Transmitters per Receiver
100 transmitters
LED Functionality
Blue
Relay Activity
Receiver/Transmitter
Red
Learn
Dimensions
(L×W×H)
Receiver
Transmitter
2.75” × 2.125” × 1.0”
(7.0 cm x 5.38 cm x 2.54 cm)
2.75” × 1.375” × 0.6”
(7.0 cm x 3.49 cm x 1.52)
Certifications
BEA Inc.
RIDC Park West
100 Enterprise Drive
Pittsburgh, PA 15275-1213
Phone: 1.800.52v3.2462
Fax: 1.888.523.2462
79.0252.01 20151203
CE, FCC, IC www.BEAinc.com
Dimensions:
www.BEAinc.com
BEA Inc.
RIDC Park West
100 Enterprise Drive
Pittsburgh, PA 15275-1213
Phone: 1.800.523.2462
Fax: 1.888.523.2462
79.0252
