ROCKET
LINX ES7110
ES7110/ES7110-VB
QUICK INSTALLATION GUIDE
2000550 Rev E | Release Date - August 2015
INTRODUCTION
The RocketLinx ES7110 series is an industrial Power over Ethernet (PoE) switch with eight Fast Ethernet ports and two Gigabit uplink ports to ensure high-bandwidth connection. The ES7110 is compliant with the IEEE 802.3af
PoE standard to deliver a maximum of 15.4 W per port with a total output power budget of 65W. The ES7110 series offers the following models:
• ES7110 - with eight Fast Ethernet PoE ports and two RJ45 Gigabit uplink ports (48VDC)
• ES7110-VB - with eight Fast Ethernet PoE ports and two RJ45 Gigabit uplink ports (12-24VDC)
To ensure the high quality of video data transmission, the ES7110 not only provides Gigabit bandwidth uplink for large image traffic, but also supports
QoS to adjust the priority of data transfer. Using the Fault Relay, the
ES7110 can automatically warn the administrator if there are any failures.
The compact IP30 rigid aluminum case allows the ES7110 to be reliably operated in an extreme environment. Refer to the Comtrol website for more information about specific ES7110 model features.
WIRE THE POWER
Use the following procedure to wire the power.
1. Insert the positive and negative wires (12-24AWG) into the PWR+ and
PWR contacts.
Note: Power should be disconnected from the power supply before connecting it to the switch. Otherwise, your screwdriver blade can inadvertently short your terminal connections to the grounded enclosure.
2. Tighten the wire-clamp screws to prevent the wires from coming loose.
1
Electrical Specification ES7110 ES7110-VB
Power Input 48VDC
Power Consumption (without PD loading) 7W
Power Consumption (with PD loading)
Maximum Output/Power PoE Port
Total PoE Power Budget
75W
15.4W
65W
12-24VDC
11W@ 24VDC
80W @ 24VDC
15.4W
65W
DC Power output
Power Supply
AC Power input
12 to 24AWG
Wire
Relay PWR
Power Supply Requirements
ES7110 48VDC/96W (Min)
ES7110-VB 12-24VDC/96W (Min)
WIRE THE ALARM RELAY OUTPUT AND GROUND
The ES7110 provides one alarm relay output. The relay contacts are energized (open) for normal operation and close under a faulty condition, such as an Ethernet port link break. Configure the alarm relay output with the DIP switches.
1. Insert positive and negative wires into Relay A and Relay B.
2. Tighten the wire-clamp screws to prevent the wires from coming loose.
3. Connect a ground wire between the chassis and earth ground using
12-24AWG wire to ensure that the ES7110 is not damaged by noise or electrical shock.
a. Loosen the earth ground screw on the bottom of the ES7110
with a screw driver.
b. Tighten the screw after the earth ground wire is connected.
2
Earth Ground
Maximum 1A/24VDC
Alarm System
Extra Power
System
Port Alarm
SET THE DIP SWITCH
The ES7110 has a 10-pin DIP switch located on the bottom panel to configure the Port Link Alarm for the Ethernet ports. The following table shows the DIP switch number mapping to the corresponding
PoE and Gigabit ports as follows.
Port G2 Port G1 Port 1 Port 2 Port 3 Port 4 Port 5 Port 6 Port 7 Port 8
DIP 1 DIP 2 DIP 3 DIP 4 DIP 5 DIP 6 DIP 7 DIP 8 DIP 9 DIP 10
The port break alarm is limited to an auto-negotiation 10/100 full-duplex device.
3
DIP Switch Status
1 - 2 On
3 - 10
Description
Enables the Gigabit port failure alarm for this port
Off (Default) Disables the Gigabit port failure alarm for this port
On Enables the PoE port failure alarm for this port
Off (Default) Disables the PoE port failure alarm for this port
MOUNT THE ES7110
The ES7110 can be mounted on a DIN rail or on a wall panel. The DIN rail clip is already attached to the ES7110 at the factory.
Note: The ES7110 will disperse heat through the metal case during PoE port operation. The ES7110 should be installed and mounted onto a panel that provides good heat dispersion.
You can use this procedure to mount the ES7110 on a DIN rail.
1. Insert the upper end of the DIN rail clip into the back of the DIN rail track from its upper side.
2. Lightly push the bottom of the DIN rail clip into the track.
3. Verify that the DIN rail clip is tightly attached to the track.
CONNECT THE POE OR RJ45 UPLINK PORTS
You can use the following information to connect Ethernet cables between the ES7110 ports and the network nodes.
• Ports G1 and G2 are Gigabit Ethernet ports that support 10BASE-T,
100BASE-TX, and 1000BASE-TX.
• Ports 1-8 are Fast Ethernet 10/100BASE-TX PoE ports that are IEEE
802.3af (PoE) compliant. The Fast Ethernet ports support 10BASE-T and
100BASE-TX, full- or half-duplex modes.
The following table shows the RJ45 pin-out assignments for the PoE and
Gigabit ports.
All ports automatically detect the signal from the connected devices to negotiate the link speed and duplex mode. Auto MDI/MDIX allows you to connect another switch, hub, or workstation without changing straightthrough or crossover cables. Crossover cables cross-connect the transmit lines at each end to the received lines at the opposite end.
4
Connect one side of an Ethernet cable into any switch port and connect the other side to your attached device. Make sure that the cables are less than
100 meters (328 feet).
1000BASE-TX
• Uplink ports:
10BASE-T: 2-pair
Category 3, 4, 5
cable
• Uplink ports:
100BASE-TX:
2-pair Category 5
• Uplink ports:
1000BASE-TX:
4-pair Category 5
cable
• PoE ports: 4-pair
Category 5e / 6
cable
RJ45 Pin 10/100BASE-TX PoE
(Alternative B)
5
6
7
3
4
1
2
8
RX+
RX -
TX +
Vport+
Vport+
TX -
Vport-
Vport-
BI_DA+
BI_DA-
BI_DB+
BI_DC+
BI_DC-
BI_DB-
BI_DD+
BI_DD-
LEDs
This table provides information about the status LEDs.
LEDs Status Description
Power Green
Off
Alarm Red
Off
Valid DC input power applied
No power
A power link failure has occurred
No failure has occurred
5
This table provides details about the port status LEDs.
Port Status
PoE 1-8
Link/
Activity
PoE 1-8
Full-
Duplex/
Collision
G1/G2
Link/
Activity
G1/G2
Speed
LED Description
Green The port is connected
Blinking Transmitting or receiving packets
Off The port link is inactive
Yellow Full-duplex mode connection
Blinking Data collision
Off The link is inactive or operating in half-duplex mode
Green The port is connected
Blinking Transmitting or receiving
Off The port link is inactive
Yellow Full-duplex mode connection
Blinking 3 blinks per cycle -
1000Mbps
2 blinks per cycle -
100Mbps
1 blink per cycle -
10Mbps
Off The link is inactive
6
COMTROL CUSTOMER SERVICE
You can use one of the following methods to contact Comtrol.
Contact Method
Support
Downloads
Website
Phone
Web Address or Phone Number http://www.comtrol.com/support http://downloads.comtrol.com/html/default.htm
http://www.comtrol.com
+1 763.957.6000
7
