Comtrol ES7110-VB Installation Guide

Comtrol ES7110-VB is an industrial Power over Ethernet (PoE) switch designed for use in harsh environments. It features eight Fast Ethernet PoE ports and two Gigabit uplink ports, allowing for high-bandwidth connections. The ES7110-VB is compliant with the IEEE 802.3af PoE standard and can deliver a maximum of 15.4W per port with a total output power budget of 65W. This makes it suitable for powering IP cameras, VoIP phones, and other PoE-powered devices.

In addition to its PoE capabilities, the ES7110-VB also supports QoS (Quality of Service) to prioritize traffic and ensure that critical data is delivered with minimal latency. It also has a Fault Relay that can be used to alert administrators of any failures, such as a port link break.

PDF

Belge

Reklam

ROCKET

LINX ES7110

ES7110/ES7110-VB

QUICK INSTALLATION GUIDE

2000550 Rev E | Release Date - August 2015

INTRODUCTION

The RocketLinx ES7110 series is an industrial Power over Ethernet (PoE) switch with eight Fast Ethernet ports and two Gigabit uplink ports to ensure high-bandwidth connection. The ES7110 is compliant with the IEEE 802.3af

PoE standard to deliver a maximum of 15.4 W per port with a total output power budget of 65W. The ES7110 series offers the following models:

• ES7110 - with eight Fast Ethernet PoE ports and two RJ45 Gigabit uplink ports (48VDC)

• ES7110-VB - with eight Fast Ethernet PoE ports and two RJ45 Gigabit uplink ports (12-24VDC)

To ensure the high quality of video data transmission, the ES7110 not only provides Gigabit bandwidth uplink for large image traffic, but also supports

QoS to adjust the priority of data transfer. Using the Fault Relay, the

ES7110 can automatically warn the administrator if there are any failures.

The compact IP30 rigid aluminum case allows the ES7110 to be reliably operated in an extreme environment. Refer to the Comtrol website for more information about specific ES7110 model features.

WIRE THE POWER

Use the following procedure to wire the power.

1. Insert the positive and negative wires (12-24AWG) into the PWR+ and

PWR contacts.

Note: Power should be disconnected from the power supply before connecting it to the switch. Otherwise, your screwdriver blade can inadvertently short your terminal connections to the grounded enclosure.

2. Tighten the wire-clamp screws to prevent the wires from coming loose.

Electrical Specification ES7110 ES7110-VB

Power Input 48VDC

Power Consumption (without PD loading) 7W

Power Consumption (with PD loading)

Maximum Output/Power PoE Port

Total PoE Power Budget

75W

15.4W

65W

12-24VDC

11W@ 24VDC

80W @ 24VDC

15.4W

65W

DC Power output

Power Supply

AC Power input

12 to 24AWG

Wire

Relay PWR

Power Supply Requirements

ES7110 48VDC/96W (Min)

ES7110-VB 12-24VDC/96W (Min)

WIRE THE ALARM RELAY OUTPUT AND GROUND

The ES7110 provides one alarm relay output. The relay contacts are energized (open) for normal operation and close under a faulty condition, such as an Ethernet port link break. Configure the alarm relay output with the DIP switches.

1. Insert positive and negative wires into Relay A and Relay B.

2. Tighten the wire-clamp screws to prevent the wires from coming loose.

3. Connect a ground wire between the chassis and earth ground using

12-24AWG wire to ensure that the ES7110 is not damaged by noise or electrical shock.

a. Loosen the earth ground screw on the bottom of the ES7110

with a screw driver.

b. Tighten the screw after the earth ground wire is connected.

Earth Ground

Maximum 1A/24VDC

Alarm System

Extra Power

System

Port Alarm

SET THE DIP SWITCH

The ES7110 has a 10-pin DIP switch located on the bottom panel to configure the Port Link Alarm for the Ethernet ports. The following table shows the DIP switch number mapping to the corresponding

PoE and Gigabit ports as follows.

Port G2 Port G1 Port 1 Port 2 Port 3 Port 4 Port 5 Port 6 Port 7 Port 8

DIP 1 DIP 2 DIP 3 DIP 4 DIP 5 DIP 6 DIP 7 DIP 8 DIP 9 DIP 10

The port break alarm is limited to an auto-negotiation 10/100 full-duplex device.

DIP Switch Status

1 - 2 On

3 - 10

Description

Enables the Gigabit port failure alarm for this port

Off (Default) Disables the Gigabit port failure alarm for this port

On Enables the PoE port failure alarm for this port

Off (Default) Disables the PoE port failure alarm for this port

MOUNT THE ES7110

The ES7110 can be mounted on a DIN rail or on a wall panel. The DIN rail clip is already attached to the ES7110 at the factory.

Note: The ES7110 will disperse heat through the metal case during PoE port operation. The ES7110 should be installed and mounted onto a panel that provides good heat dispersion.

You can use this procedure to mount the ES7110 on a DIN rail.

1. Insert the upper end of the DIN rail clip into the back of the DIN rail track from its upper side.

2. Lightly push the bottom of the DIN rail clip into the track.

3. Verify that the DIN rail clip is tightly attached to the track.

CONNECT THE POE OR RJ45 UPLINK PORTS

You can use the following information to connect Ethernet cables between the ES7110 ports and the network nodes.

• Ports G1 and G2 are Gigabit Ethernet ports that support 10BASE-T,

100BASE-TX, and 1000BASE-TX.

• Ports 1-8 are Fast Ethernet 10/100BASE-TX PoE ports that are IEEE

802.3af (PoE) compliant. The Fast Ethernet ports support 10BASE-T and

100BASE-TX, full- or half-duplex modes.

The following table shows the RJ45 pin-out assignments for the PoE and

Gigabit ports.

All ports automatically detect the signal from the connected devices to negotiate the link speed and duplex mode. Auto MDI/MDIX allows you to connect another switch, hub, or workstation without changing straightthrough or crossover cables. Crossover cables cross-connect the transmit lines at each end to the received lines at the opposite end.

Connect one side of an Ethernet cable into any switch port and connect the other side to your attached device. Make sure that the cables are less than

100 meters (328 feet).

1000BASE-TX

• Uplink ports:

10BASE-T: 2-pair

Category 3, 4, 5

cable

• Uplink ports:

100BASE-TX:

2-pair Category 5

• Uplink ports:

1000BASE-TX:

4-pair Category 5

cable

• PoE ports: 4-pair

Category 5e / 6

cable

RJ45 Pin 10/100BASE-TX PoE

(Alternative B)

RX+

RX -

TX +

Vport+

TX -

Vport-

BI_DA+

BI_DA-

BI_DB+

BI_DC+

BI_DC-

BI_DB-

BI_DD+

BI_DD-

LEDs

This table provides information about the status LEDs.

LEDs Status Description

Power Green

Off

Alarm Red

Off

Valid DC input power applied

No power

A power link failure has occurred

No failure has occurred

This table provides details about the port status LEDs.

Port Status

PoE 1-8

Link/

Activity

PoE 1-8

Full-

Duplex/

Collision

G1/G2

Link/

Activity

G1/G2

Speed

LED Description

Green The port is connected

Blinking Transmitting or receiving packets

Off The port link is inactive

Yellow Full-duplex mode connection

Blinking Data collision

Off The link is inactive or operating in half-duplex mode

Green The port is connected

Blinking Transmitting or receiving

Off The port link is inactive

Yellow Full-duplex mode connection

Blinking 3 blinks per cycle -

1000Mbps

2 blinks per cycle -

100Mbps

1 blink per cycle -

10Mbps

Off The link is inactive

COMTROL CUSTOMER SERVICE

You can use one of the following methods to contact Comtrol.

Contact Method

Support

Downloads

Website

Phone

Web Address or Phone Number http://www.comtrol.com/support http://downloads.comtrol.com/html/default.htm

http://www.comtrol.com

+1 763.957.6000

Merhaba! Ben, Comtrol ES7110-VB Installation Guide konusunda size yardımcı olmak için özel olarak eğitilmiş bir yapay zeka sohbet robotuyum. Belgeyi iyice inceledim ve ihtiyacınız olan kesin bilgileri bulmanıza veya içeriği açık ve basit terimlerle açıklamanıza yardımcı olabilirim. Belirli özellikler, sorun giderme adımları veya genel kullanım hakkında rehberlik arıyorsanız, sorularınızı sormaktan çekinmeyin. Endişeleriniz veya ihtiyaçlarınız hakkında ne kadar çok ayrıntı verirseniz, o kadar doğru ve etkili bir şekilde size yardımcı olabilirim!