advertisement
▼
Scroll to page 2
of 4
Installation Guide AF-AT Single Arm Desktop Monitor Mount COMPONENT CHECKLIST A VESA head (x1) D Rotation limiter (x1) B Monitor arm (x1) H Screw M8 x 60mm (x1) C Pole Assembly (x1) N Pole top cap (x1) E Primary arm cable cover (x1) I J Screw Security Screw M8 x 30mm M4 x 16mm (x1) (x1) O Bolt through base (x1) P 5mm Allen key (x1) Q Mounting screws M4 x 10mm (x4) F Secondary arm cable cover (x1) K Steel washer (x1) G Desk clamp assembly (x1) L Cable stop (x2) R Mounting screws M4 x 12mm (x4) M Cable clip (x1) S Mounting screws M4 x 16mm (x4) REQUIRED TOOLS • Phillips Head Screwdriver WEIGHT RANGE Flat Monitors 0 - 8kg (0 - 17.6lbs) Curved Monitors 0 - 5.5kg (0 - 12lbs) IMPORTANT INFORMATION ! Please ensure this product is installed as per these installation instructions. ! This product is compatible with the range of AF Poles and arms. ! The manufacturer accepts no responsibility for incorrect installation. ! Curved monitors, deep devices (such as all-in-one PCs) and offset VESA locations exert additional leverage that can exceed the capacity of the mount even though the monitor weight may be within the stated range. Please contact Atdec if you would like further information. AF-AT Page 1 of 4 1. Desk overview Desk Clamp The desk clamp bracket can be repositioned to suit different mounting surface thicknesses. Default Inverted 52mm (2.1”) 88mm (3.5”) 140mm (5.5”) 55mm (2.2”) MIN THICKNESS - 0mm (0”) MAX THICKNESS - 39mm (1.5”) MIN THICKNESS - 35mm (1.4”) MAX THICKNESS - 76mm (3”) 2. How to reconfigure desk clamp 2.1 Remove screws (M8 x 16mm Countersunk screw) 2.2 Remove clamp plate 2.3 Invert bracket 2.4 Replace clamp plate 2.5 Reattach bracket 3. Post mount configuration 3.1 Attach clamp to post 3.2 Place in desired location 3.3 Screw pressure plates in and tighten firmly. Pressure Plate M8 x 30mm Countersunk screw Tighten firmly M10 Desk Clamp Screw 5mm Allen Key 4. Bolt through - Drill Hole 5. Bolt Pole to work surface 4.1 Drill 9mm hole in desired post position on work surface. 9mm (3/8”) M8x60mm Screw 25 of mm fse t 5mm Allen Key Bolt Through Plate Note orientation of plate with pole AF-AT Page 2 of 4 6. Install VESA monitor head 6.1 Install VESA monitor head as shown. 100mm 75mm Screen VESA monitor head M4x10/12/16mm Phillips Head Mounting Screws 100mm 75mm 7. Install arm assembly 7.1 Unlock handgrip and raise so that handgrip tab protrudes Handgrip Tab 7.2 OPTIONAL ROTATION LIMITER Insert rotation limiter for 180� rotation around mounting pole 7.3 Slip the Arm Assembly over the Handgrip Tab and then onto the Pole Arm Assembly 7.4 Slide the Arm Assembly and Handgrip down the pole before locking the handgrip at the desired height 7.5 Insert Pole Top Cap into Pole. This is also where the Allen Key is stored. 5mm Allen Key Pole Top Cap 8. Mounting Monitor 8.1 Insert VESA monitor head into the receptacle in the Arm Assembly 8.2 OPTIONAL SECURITY SCREW Ensure the Monitor is supported, then loosen the Monitor head screw with the 5mm Allen Key and tilt screen up before installing the M4 x 16mm Security Screw into the Security Screw hole Monitor head screw Note: Support Screen when adjusting tilt. VESA monitor head Security Screw Hole Loosen Tighten Arm Assembly M4 x 16mm Security Screw Phillips Head Screwdriver 5mm Allen Key AF-AT Page 3 of 4 9. Adjusting Height 9.1 Unlock Handgrip ensuring both the screen and arm assembly are supported 9.2 Lift/Lower the Screen to the desired height. Move both Screen and Arm assembly together 9.3 Lock Handgrip firmly 10. Cable Management 10.1 After plugging in your cables, install the Cable Covers. 10.2 Push Cable Covers away from Elbow Joint to secure in place. 10.3 Cable Clips and Cable Stops can be installed to further manage cables. Cable Stop Lock Slot Lock Slot Insert Cable Covers up intoLock Slots. ‘click’ ‘click’ Note: Ensure enough cable slack is given to allow for movement. ‘click’ Elbow Joint Cable Clip ‘click’ Elbow Joint 11. Insert Cable Stops 11.1 Insert Cable Stop on one edge of the Pole Slot Note: Press down firmly onto the other edge of the Cable Stop and hold. This allows the rear profile to flex in place 11.2 Insert allen key into top cap on pole Allen Key Storage 12. Adjusting the Display Bracket Portrait/ Landscape Tilt (Screen angle up/down) Pan (Screen angle left/right) VESA 75 x 75 / 100 x 100mm 100mm 75mm Loosen 100mm 75mm 5mm Allen Key Tighten No Allen Key necessary Note: Support Screen when adjusting tilt. No Allen Key necessary No portion of this document or any artwork contained herein should be reproduced in any way without the express written consent of Atdec Pty Ltd. Due to continuing product development, the manufacturer reserves the right to alter specifications without notice. ©20191024A atdec.com | atdec.co.uk | atdec.com.au AF-AT Page 4 of 4
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement