Model: PRO 94 BT2
TRANSMITTER PROGRAMMING GUIDE
The transmitters included in the security system kit are pre-programmed at the factory, with button assignments (channels) prioritized in a standard format.
Refer to the chart for standard factory configuration.
Factory Settings for Transmitter Buttons
BUTTON
Button 1
CHANNEL
1
SYSTEM FUNCTION
Remote Arm/Disarm
Remote Emergency Panic
Door Lock/Unlock (Optional)
Button 2
Both Buttons
2
3
Pulsed Output
*(Optional Devices)
Switched Output
* (Optional Devices)
* Some of the more common accessories for these channels are;
AS 9151
AS 9256
AS 9154
AS 9153
Remote Car Starter
Remote Trunk Release Relay
Remote Garage Door Interface
Remote Window Roll Up
Released 7-10-95.
128-4618 sht. 1 of 4
These factory programmed settings can be prioritized based on an individual's frequency of use, (i.e. pressing both buttons simultaneously to activate channel
1, arm/disarm etc.) by following the normal programming instructions below.
Please note when changing the button sequences of the factory settings, it is necessary to perform steps 5, 9, and 12 three times using "transmitter A", followed by one time using "transmitter B".
PROGRAMMING TRANSMITTERS:
It is important to remember that during programming, each individual step of the procedure must be executed within 15 seconds of the previous step. When the
15 second time limit is allowed to expire, the system will automatically exit program mode. This is indicated by a long "chirp"(*) from the siren.
Additionally, any time the ignition key is turned off while programming, the system will immediately exit program mode. This is also indicated by a long "chirp"(*) from the siren.
TO PROGRAM ADDITIONAL TRANSMITTERS:
1. Enter the vehicle, and turn the ignition key to the "on" position.
2. Move the valet/bypass switch on - off - on - off - on then off.
3. The dash L.E.D. will flash(*) one time, and the siren will "chirp"(*) one time, indicating the system is ready to accept programming for channel 1, or the arm/disarm and panic functions.
4. You can assign any of the three transmitter button functions listed below to channel 1.
a) Pressing button 1 on the keychain transmitter.
b) Pressing button 2 on the keychain transmitter.
c) Pressing both buttons simultaneously on the keychain transmitter.
5. Press and hold the selected choice a, b, or c above, until the siren emits a long
"chirp"(*) to confirm that programming of channel 1 was successful.
6. Move the valet/bypass switch on, then off again.
7. The dash mounted L.E.D. will flash (*) 2 times, and the siren will "chirp"(*) one time, indicating that the system is ready to accept programming for channel
2, or the pulsed ground output for remote trunk release, remote car starter, etc.
8. You can assign any one of the two remaining button functions listed in 4a, 4b, or 4c above to operate channel 2. You cannot use the button(s) that operate channel 1, selected in step 5, to operate channel 2.
9. Press and hold the selected choice. The siren will emit a long "chirp"(*) to confirm that programming of channel 2 was successful.
* Except PRO-9246R & PRO-9445
128-4618 sht. 2 of 4
10. Move the valet/bypass switch on, then off again.
11. The dash mounted L.E.D. will flash(*) 3 times, and the siren will "chirp"(*) one time, indicating that the system is ready to accept programming for channel
3. (PRO-9249R & PRO-9246R)
12. Press and hold the remaining transmitter button function. The siren will emit a long "chirp"(*) to confirm that programming of channel 3 was successful.
13. To exit program mode, either turn the ignition key to the off position, or move the valet switch on then off one additional time. This is indicated by a long
"chirp"(*) from the siren.
QUICK REFERENCE:
You can program any individual channel, without reprogramming all channels, by following the quick reference chart below.
CHANNEL
1
2
3
VALET SWITCH
ON then OFF 3 Times
ON then OFF 4 Times
ON then OFF 5 Times
L.E.D.
1 Flash
2 Flashes
3 Flashes
After the desired channel is programmed, turn the ignition key to the off position to exit programming mode.
* Except PRO-9246R & PRO-9445
BATTERY REPLACEMENT:
The transmitter incorporates a small red L.E.D. built into the case. This L.E.D.
can be used to indicate battery condition. You will notice a decrease in transmitter range as the battery condition deteriorates. To replace the battery...
1. Remove the transmitter cover by removing the small screw from the back of the transmitter case.
2. Remove the discharged battery, making note of the orientation of the + and
- contacts, and dispose of properly.
3. Install the new (type GP 23A) battery, taking care to orient the + and - contacts properly.
4. Replace the transmitter cover, taking care not to damage the L.E.D. or switches on the circuit board.
128-4618 sht. 3 of 4
ORDER FORM FOR 2 BUTTON TRANSMITTER
MODEL NO. PRO 94 BT2
IMPORTANT: To help us expedite your order, please print all of the information legibly, and mail this form and your payment according to the instructions below.
1. Name : ________________________________________________________
Address : ________________________________________________________
City : ______________________ State : ________ Zip Code : ________________
2. Telephone Number : (__________) __________________________________
3. Enter the total number of transmitters required here : ______________________
4. The cost per transmitter is $ 65.00.
5. Enter the total amount enclosed here : _________________________________
( New York state residents must include the appropriate sales tax. )
6. Method of payment; check one of the boxes below.
Mastercard
Visa
Check or money order * (do not send cash)
* Make checks payable to Audiovox Corporation
7. Credit Card Number : _____________________________________________
8. Credit Card Expiration Date : _________________________
Credit card purchasers can order additional or replacement transmitters by phone. Simply dial 1 - 800 - 645 - 4994, and follow the instructions from the operator interface.
9. Mail this form, and your check, to ;
Audiovox Corporation
150 Marcus Blvd.
Hauppauge, N.Y. 11788
Attn: TRANSMITTER DEPARTMENT
Form No. 128-4618
128-4618 sht. 4 of 4
