advertisement
Updated 07/2002
Special
Order
Products
MY-CU-PH/B
Video Monitor
MK Video Door Answering with Panasonic® Phone System
- INSTRUCTIONS -
This monitor allows one or two MK video door stations to be used for video door answering, where the communication is through a Panasonic® telephone system and the video appears on the Aiphone monitor(s). The MY-CU-PH/B integrates MK PanTilt door stations with Panasonic's KX-T series systems. (Works with KX-TA Advanced Hybrid series and KX-TD Digital Super Hybrid series.)
WIRING DIAGRAM:
MK-DBC*
A1
A2
MY-CU-PH/B
1A1
1A2
MYH-CU
+
-
U1
U2
A1
A2
B1
B2
VIDEO OUTPUT TO CABLE
DISTRIBUTION OR CCTV MONITOR:
Use Aiphone MYW-MD/B Demodulator, wired with 4 conductor, 18 AWG wire from the MY-CU-PH/B monitor or last MYH-CU in the system. Output is a standard 1V peak-to-peak video signal.
MK-DBC*
A1
A2
*VIDEO DOOR STATIONS:
Any Aiphone MK or MY Series video door station can be used:
-MK-DAC: Surface mount, black
-MK-DBC: Semi-flush mount, black
-MK-DGC: Semi-flush mount, metal cover
-MK-DGV: Semi-flush mount, vandal
proof, stainless steel cover
-MK-DS/B: Surface mount, fixed camera,
Black
PS-1820UL
+
-
2A1
2A2
B1
B2
+
-
U1
U2
MYH-CU
+
-
U1
U2
B1
B2
A1
A2 PS-1820UL
+
-
MYW-MD/B
DA1
DA2
+
-
DV+
DV-
Move jumper to bottom 2 pins
DV+ to core of Coax
DV- to shield of coax
Raw video output
MY-CU-PH/B TERMINAL DEFINITIONS:
1A1 2-Wire connection
1A2 for Door Station #1
2A1
2A2
B1
B2
U1
U2
-
+
2-Wire connection for Door Station #2
Video out to sub monitors
Control wires
Control wires
Positive 18V DC
Negative
To Panasonic Phone System:
D1
D2
E
Door 1 call-in & audio
Door 2 call-in & audio
Common audio
D1
E
D2
(Analog wiring shown)
1 2
3 4
PHONE JACK TERMINAL BLOCK WIRING
With KX-TA62460 Doorphone card (Analog):
D1 = 1 (Green)
D2 = 3 (Black)
E = 2 (Red)
E = 4 (Yellow)
Modular cord from terminal block to Door
Adaptor in
Panasonic KSU
With KX-TD160 Doorphone card (Digital):
D1 = 2 (Red) E = 1 (Green)
D2 = 4 (Yellow) E = 3 (Black)
With KX-TD161 Doorphone card (Digital):
D1 = 1 (Green) E = 2 (Red)
D2 = 4 (Yellow) E = 3 (Black)
SPECIFICATIONS:
Power Source:
Consumption:
18V DC.
Use one PS-1820UL for every three monitors.
MY-CU-PH/B Standby: 0.12A; Max. 0.9A
MYH-CU Standby: 0A; Max .4A
Communication:
Calling:
Video Monitor:
Through Panasonic® Telephone system
Hands free at door station
Monitors activate and Panasonic phones ring
4" direct view flat CRT
Scanning lines: 525 lines
Dimensions (HxWxD): 8-14"" x 6" x 2"
Weight: MY-CU-PH/B: 2.2 lbs.
MYH-CU: 1.98 lbs Pg. 1
OPERATIONS:
RECEIVING A CALL FROM THE DOOR STATION:
1. When the door station button is pressed, the MY-CU-PH/B and any additional monitors come
on and the telephones ring, indicating a call from the door.
2. To answer the call, simply pick up the telephone at any extension. The visitor speaks hands free.
3. If the handset isn't picked up, the monitor will turn off automatically in approximately 45 seconds.
If the call is answered, the monitor will turn off when the handset is hung up.
4. If there are two door stations in the system, a phone with an LCD readout will indicate which door
is calling in, and the view from the calling door will be seen on the monitors. When any handset is
picked up, the communication will be established with the calling door station location.
MONITORING FROM INSIDE
1. To view outside from the monitor, press the MONITOR button. The video door station angle can
be adjusted to view a wider area with the PanTilt control pad. (Overall viewing range of the MK series
cameras is 70" x 35".) To turn the monitor off, press MONITOR again, or it will automatically turn off in
approximately 2-½ minutes.
2. If two video door stations are included in the system, pressing the MONITOR button once
activates camera #1, twice activates camera #2, and a third time turns the monitor off.
3. To establish two way communication with the door station from inside, pick up the handset or
press "speakerphone", and dial the door station number (intercom 31 or 32). The monitor will also
come on with a view of the entry area when the door is called from a phone. The monitor will stay
on for approximately 2-½ minutes, or until the communication is completed.
VIDEO OUTPUT TO CABLE DISTRIBUTION OR CCTV MONITOR:
(Output from MYW-MD/B is standard 1V, peak to peak video.)
1. For video output on the system, use the MYW-MD/B Demodulator. The output can be wired with coaxial
cable to a multiplexing system, or into a standard monitor input. If connecting into a
television input, an RF modulator is required (Not supplied by Aiphone).
2. When the MY-CU-PH/B monitor is on, the video signal will be present.
3. When a call is heard from a door station, the TV can be changed to the channel that the door
camera is assigned to, and a view of the entry area will be seen. Simply pick up the phone to
speak to the visitor while viewing the TV.
AUDIO ONLY DOOR STATION:
1. The Panasonic® phone system allows two door stations to be included. When a second "audio only" door
station is required, use the Panasonic® audio door station. The call-in and communication functions are
the same as described above.
WIRING:
MK Door station to MY-CU-PH/B
MY-CU-PH/B to KSU
MY-CU-PH/B to MYH-CU
Monitor to MYW-MD/B
PS-18C to MY-CU-PH/B
# of wires
2 cond.
2 c. per door
6 cond.
4 or 6 cond.
2 cond.
Gauge
18
22 or 18
18
18
18
Distance
330'
500'
245'
245'
16'
Aiphone Wire #
841802
822202, 841802
841806
841806
841802
COMPATIBILITY:
The MY-CU-PH/B Video door answering monitor interfaces with selected Panasonic® phone systems.
Compatible with:
KX-TA62460 Doorphone card.
KX-TD160 Doorphone card.
KX-TD161 Doorphone card.
Aiphone Communication Systems
1700 130th Ave. N.E.
Bellevue, WA 98005
(425) 455-0510
FAX (425) 455-0071
TOLL FREE TECHNICAL SUPPORT:
(800) 692-0200
TOLL FREE FAX LINE:
(800) 832-3765
E-MAIL: [email protected]
Pg. 2
MY-CU-PH/B Instr.
0703bkjs
advertisement
Related manuals
advertisement