The Power of Being There
Quick Installation Guide
DSR
®
1021/1022 Switch
The following instructions will help you
to connect your DSR switch.
To connect a DSR switch
Should you require further assistance, please
consult your installer/user guide.
1 Connecting power to the
DSR switch
Power down all servers that will be part of your DSR switching system. Locate the power cord that came with the DSR switch. Plug one end into the power socket on the rear of the DSR switch. Plug the other end into an appropriate AC wall outlet.
5
Connect the switch to the network.
2
Connecting the local port
Plug a VGA monitor and the PS/2 keyboard and mouse cables into the appropriately labeled
DSR ports.
1
Power down all servers and attach the appropriate power cord to the
DSR switch.
3 Connecting a DSRIQ module to the DSR switch
Choose an available port on the rear of your DSR switch. Plug one end of a CAT 5 cable (4-pair, up to
10 meters) into a numbered port and plug the other end into the RJ-45 connector of a DSRIQ module.
4
Connecting a server to the
DSRIQ module
Plug the DSRIQ module into the appropriate ports on the back of the server. Repeat this procedure for all servers that are to be connected to the DSR switch.
7
Connect your
SPC device to the target servers.
5 Connecting network users
Plug a CAT 5 cable from your Ethernet network into the LAN connector on the back of your DSR switch.
Network users will access the DSR switch through this port.
(Continued on reverse side)
A1
2
Ethernet
Plug in the keyboard, monitor and mouse for your local connection.
SPC Power
Control Device
Modem
Telephone network
DSR1021 Switch
Local Connection
Server
Server
Server
Server
6
Plug in the external modem.
3
Connect DSRIQ modules to the
DSR switch.
4
Connect servers to the DSRIQ modules.
8
Power up target servers and then the
DSR switch.
Check our web site at www.avocent.com/support to search the knowledge base or use the online request.
Avocent, the Avocent logo, The Power of Being There and DSR are registered trademarks of Avocent Corporation. All other marks are the property of their respective owners. ©2004 Avocent Corporation. All rights reserved. 590-4286 03A
The Power of Being There
Quick Installation Guide
DSR
®
1021/1022 Switch
The following instructions will help you
to connect your DSR switch.
To connect a DSR switch
(continued from reverse side)
Should you require further assistance, please
consult your installer/user guide.
5
Connect the switch to the network.
6 Connecting an external modem (optional)
The DSR switch may also be accessed using an
ITU V.92, V.90 or V.34-compatible modem. Plug one end of a 9-pin serial cable into the MODEM connector on the back of your DSR switch. Plug the other end into the connector on the back of the modem.
NOTE: Using a modem connection instead of a
LAN connection will limit the performance capability of your DSR switch.
1
Power down all servers and attach the appropriate power cord to the
DSR switch.
Ethernet
Modem
A1
2
Plug in the keyboard, monitor and mouse for your local connection.
Telephone network
DSR1021 Switch
Local Connection
7
Connecting the SPC device to the
DSR switch (optional)
Plug one end of the cable supplied with the SPC power control device into the SPC connector on the
DSR switch and plug the other end into the SPC device. Plug the power cords from the target servers into the SPC power outlets. Plug the SPC device into an appropriate AC wall outlet.
8
Power up targets and switch
Power up each target server and then power up the
DSR switch.
7
Connect your
SPC device to the target servers.
For additional information
For further instructions on DSR switch connection, software setup and security configuration, please refer to the installer/user guide included with the switch. Check http://register.avocent.com for the latest DSR software and firmware updates.
SPC Power
Control Device
Server
Server
Server
Server
Check our web site at www.avocent.com/support to search the knowledge base or use the online request.
Avocent, the Avocent logo, The Power of Being There and DSR are registered trademarks of Avocent Corporation. All other marks are the property of their respective owners. ©2004 Avocent Corporation. All rights reserved.
6
Plug in the external modem.
3
Connect DSRIQ modules to the
DSR switch.
4
Connect servers to the DSRIQ modules.
8
Power up target servers and then the DSR switch.
A1
The Power of Being There
A1
The Power of Being There
A1
The Power of Being There
A1
The Power of Being There
A1
The Power of Being There
A1
The Power of Being There
