5. Select the name of your

••• ISP. In PPPoE or

••• PPPoA mode, the

••• wizard asks the user

••• name and password.

••• Key in the information

••• and then click to the

••• next step. This page

••• does not appear in route

••• mode. If so, just go to the

••• next step.

6. This page shows the

••• service provider,

••• Encapsulation, protocol

••• and VPI/VCI values.

••• Check the configuration is

••• correct then click .

7. The installation is in

••• progress.

8. Wait the installation

••• completely. Click to exit

••• the Wizard.

9. In PPPoE and PPPoA connection mode, it creates two icons

••• on the desk top, “ AccessRunner DSL ” and “ AccessRunner

••• Control Panel ” .

10. If the service is not PPPoE

••••• or PPPoA, you still can find

••••• “ AccessRunner Control

••••• Panel ” in “ Control Panel ”

••••• field.

11. Double click

••••• “ AccessRunner DSL ” then

••••• click “ Dial ” box to connect

••••• to the ISP.

6 5

12. When the connection is

••••• up, the connection

••••• status will show the

••••• speed is 1.0 Mbps in the

••••• task bar.

13. “ Access Runner Control

••••• Panel ” is the utility to

••••• check the connection

••••• status and change the

••••• setting as you need.

••••• Double click the icon to

••••• open the utility.

14. Click Alt+P to open the content.

15. For more information please refer the manual on the CD

••••• and the Utility on-line manual under the root of

••••• Program.

P/N 2300-0348

Quick Installation Guide

ADSL USB Modem

Model No.: SP3302A

Web: www.micronet.info

7

Introduction

The ADSL USB Modem is capable of bringing data, voice and video into your computer 142 times faster than 56K modem. It provides a downloading speed up to 8 Mbps, and uploading speeds up to 1 Mbps. This bus-powered modem needs no external power or AC cords, and features a compact design. It is suitable for only one computer accessing Internet over ADSL line in your home or office.

Package Content

• ADSL USB Modem

• Quick Installation Guide

• Manual & Driver CD

• RJ-11 Cable

• USB Cable

Features

• Support ANSI T1.413 issue 2

• Support ITU G.992.1 (G.DMT)

• Support ITU G.992.2 (G.lite)

• Support G.994.1 (G.hs, Multimode)

• ADSL over POTS (Annex A) or ADSL over ISDN (Annex

• B/UR2)

• Maximum downstream rate up to 8Mbps

• Maximum upstream rate up to 1Mbps

• PPP over ATM VCMUX (RFC 2364)

• PPP over ATM LLC (RFC 2364)

• PPP over Ethernet VCMUX (RFC 2516)

• PPP over Ethernet LLCSNAP (RFC 2516)

• Bridged IP over ATM LLCSNAP (RFC 1483)

• Bridged IP over ATM VCMUX (RFC 1483)

• Routed IP over ATM LLCSNAP (RFC 1483)

• Classical IP over ATM (RFC 1577)

• Support VPI value range 0~255 and VCI value range 32~1023

1

System Requirements

• Pentium II 233MHz processor or above

• 64MB system memory or more

• 20MB available space on hard drive

• CD-ROM drive

• One available USB port

• Available ADSL service or connection to DSLAM or ADSL

• service emulator

• Microsoft Windows 98SE, ME, 2000, XP

Installation

The following instructions apply for Windows 98SE, ME, 2000 and XP. The auto-run program controls the whole instruction procedures. Only take a look at the country selected, user name and password.

1. Connect the ADSL USB

••• Modem to one of USB

••• ports on the computer.

••• System will detect a new

••• USB device is connected.

2. Click “ Cancel ” when the

••• “ Found New hardware

••• Wizard ” pops up.

3

2

3. Insert the CD in the CD

••• drive and wait the auto-

••• run program running a nd

••• popping up the selection

••• page.

4. Select “ Install Driver ” and click the hand icon to switch

••• between the two pages. Find your country name in the list.

••• There is a mark at the right corner, click the mark to go •••

••• to the next step.

4