KitchenAid KONP 6610/IX Oven Program Chart

Instructions for use

Installing the built-in / under the counter column oven

Safeguarding the environment

Warnings

Before using the oven

Oven accessories

Care and Maintenance

Troubleshooting guide

After Sales Service

13

13

8

9

6

7

5

6

Installing the built-in / under the counter column oven

Recommendations

Important: Disconnect the oven from the mains before carrying out any installation work or servicing.

• It must be installed by a qualified electrician following the instructions provided by the manufacturer and in compliance with local safety standards in force.

• Once you have unpacked the oven, check that the appliance has not been damaged during transportation and that the door closes properly. If you have any doubts, contact the Customer Care

Centre.

• Once you have unpacked the oven, avoid removing it from the polystyrene base: this will prevent the appliance from getting damaged.

• You should wear protective gloves when installing the appliance.

• The oven has two proFIT ( B ) side handles, there to make installation easier (Fig. 7).

Preparing the housing unit

• The kitchen units next to the oven must be heat resistant (min.

90°C).

• Cut the kitchen unit to fit before installing the appliance. Make sure you remove all the wood shavings that could inhibit the perfect functioning of the appliance.

• The dimensions of the housing unit are shown in Figures 1, 2 and

3. The oven dimensions are shown in Figure 4.

• In order to ensure adequate ventilation, leave an open space at the back of the unit (following the sizes indicated in the Figure 6).

When installation has been completed, the bottom of the oven must be inaccessible.

• Install the oven taking care that their walls do not come into direct contact with the adjacent units (Fig. 5).

• With ovens installed under worktops, there must be a slot of at least 5mm between the upper border of the oven and the lower border of the worktop (Fig. 5). Do not obstruct this slot in anyway as this could compromise the perfect working order of the appliance.

• If the kitchen unit is not securely fixed to the wall, it must be anchored with standard brackets ( A ) (Fig. 6) available on the market.

Fig. 3

Fig. 1

Fig. 2

Fig. 6 Fig. 4

4

Fig. 5

Installing the built-in / under the counter column oven

Electrical connection

Regulations require that the apparatus be earthed.

• The electrical connection must be made by a qualified electrician following the instructions provided by the manufacturer and in compliance with local safety standards in force.

• The installer is responsible for ensuring that the electrical connection of the appliance is carried out properly and in compliance with local safety standards in force.

• The oven power cable must be long enough to connect the builtin appliance to the mains.

• Observance of safety directives requires that a multi pole switch with a minimum contact gap of 3 mm be used for the installation.

• Never use adapters or extension leads.

• Once the installation is complete, the electrical parts should no longer be accessible.

Connecting to the oven

• Make sure that the voltage indicated on the rating plate is the same as the mains voltage. The rating plate is on the front edge of the oven (visible when the door is open).

• If the oven does not have a power supply cable proceed as follows:

1. Remove the two fastening screws of the terminal box cover located on the bottom part of the oven's rear covering.

2. Remove the cover to gain access to the terminal box cover and insert the power cable (see table) through the opening located on the bottom of the oven.

3. Connect the cable to the terminal box, tighten the screws as far as they will go and secure it to the cable fastener.

4. Put the cover back on by inserting the two blades in the slots and fasten it with the two screws.

Fig. 7

Power supply cable table

No. of conductors Type of cable

IN+ ~ H05 RR-F 3 X 1,5 mm 2

Securing the oven

• Lift the oven using the proFIT handles on each side ( B ) and insert it in the unit, making sure you do not get the power supply cable caught (Fig. 8).

• Center the oven in the housing unit before securing it definitively.

• Continue fitting the oven into the unit using the screws provided

(as shown in Fig. 9).

Fig. 8

Fig. 9

5

Safeguarding the environment

Disposing of packaging

• The packing material can be 100% recycled as confirmed by the recycling symbol .

• The various pieces of packaging should not be disposed off into the environment but disposed of in compliance with local authority standards.

Disposal of old appliances

• The appliances are made with recyclable or re-usable material. Disposal must be carried out in accordance with local environmental regulations for waste disposal. Cut the power cable to make them unusable before disposing of them.

Product

• This appliance is marked according to the European Directive 2002/96/EC, Waste Electrical and

Electronic Equipment (WEEE).

• By ensuring that this product is disposed of correctly, you will help prevent potentially negative consequences for the environment and human health.

• The symbol on the product or on the documents accompanying the product indicates that this appliance should not be treated as household waste. Instead, it should be handed over to the applicable collection point for the recycling of electrical and electronic equipment.

Disposal must be carried out in accordance with local environmental regulations for waste disposal.For

more detailed information on treatment, recovery and recycling of this product, contact your local authority, the household waste disposal service or the shop where you purchased the product.

Energy saving

• Only preheat the oven if indicated in the product description sheet cooking table or in your recipe.

• Use dark, black lacquered or varnished oven moulds because they absorb heat much better.

Warnings

• This appliance is not intended for use by persons (including children) with reduced physical, sensor or mental capabilities or lack of experience and knowledge unless they have been given initial supervision or instruction concerning use of the applaince by a person responsible for their safety.

• The oven is for home use and the cooking of food only. No other use is allowed. The Manufacturer denies all responsibility for improper use or for the incorrect setting of the controls.

• Only a qualified electrician can carry out repair work or maintenance.

• Avoid exposing the oven to atmospheric agents.

• Do not place heavy items on the door as this could damage the oven opening and the hinges.

• Do not hang onto the door.

• Do not hang anything on the oven door handle.

• Do not cover the bottom of the oven with aluminium foil or other objects.

• The oven door must shut properly. Keep the door seal surfaces clean.

• Never pour water directly into a hot oven. The varnish could get damaged.

• Fruit juices that drip from a tray could leave indelible marks. We would advise you to clean the oven before using it again.

• Do not drag pots or pans across the bottom of the oven as this could scratch the surface.

6

Warnings

• Residual condensation after the last use, could over time, damage the oven and the surrounding units.

We advise you to:

- always use the lowest temperature;

- cover the food;

- remove the food from the oven when cooked;

- dry the damp parts of the cold oven.

• The oven screen and door handle heat up when the appliance stays on for a long period of time at a high temperature.

• Never touch the oven with any wet part of the body or operate it with bare feet.

• Do not pull the appliance or power cable to disconnect it from the socket.

• Keep children away from:

- the oven and its controls, especially during or just after use, to prevent injury;

- packaging (bags, polystyrene, metal parts, etc.)

- the oven when scrapped.

• Make sure the wiring from other appliances in use near the oven do not come into contact with hot parts of the oven and do not get trapped in the oven door.

• The oven is fitted with an air cooling system to prevent the front part and the cabinet cavity from reaching excessively high temperatures.

Attention: steam and smoke are vented through an opening between the control panel and the oven door. Do not obstruct the vent opening.

• Do not place inflammable material in the oven or near it: if the appliance is inadvertently turned on, a fire could start.

• Use oven gloves to remove hot pans and accessories in the oven.

• If you are adding alcohol (e.g. rum, cognac, wine etc.) while roasting meats or baking cakes, remember that alcohol evaporates at a high temperature. You should, therefore, bear in mind that the vapours released by the alcohol can ignite when they come into contact with the electrical heating element.

• Do not heat up or cook food in sealed containers inside the oven. The pressure that builds up inside the container could explode, damaging the oven.

• Do not use containers made of synthetic material to cook (except ones specifically designed for this purpose; see information provided by the Manufacturer). They could melt at high temperature.

• Keep an eye on what you are cooking if you are using a lot of fat or oil. The oil and fat could overheat and cause a fire!

• Never pull out fully loaded shelves. Use extreme caution.

Before using the oven

• Before use, remove:

- stickers on the front of the oven and the door with the exception of the rating plate.

- cardboard protection and protective plastic film from the control screen and other parts of the oven

- any sticky labels from accessories (for example, under the drip tray).

• Remove the accessories from the oven and heat it up at 200°C for approx. one hour to eliminate smells and fumes produced by insulating material and protective greases. You should keep the window open when doing this.

7

Oven accessories

The accessories vary according to the model. The accessories provided with the oven are listed in the separate Product

Description Sheet (under Accessories).

Drip tray (1)

Placed under the grid to collect grease or pieces of food or used as a plate, for example, to cook meat, chicken, fish with or without vegetables. Pour some water into the drip tray to prevent fat spatters or smoke.

Baking tray (2)

For baking biscuits, cakes and pizzas.

Wire shelf (3)

For cooking food or as a support for pots, cake tins and any other cooking receptacles. It can be placed on any of the runners in the oven. The wire shelf can be inserted with the curved side upwards or downwards.

Turnspit (4)

See relative chapter in the separate Product Description Sheet for use.

Grill Pan Set (5)

The set includes a trivet, an enamel drip tray and a handle. The Grill pan should be placed on the wire shelf and used with the Grill function

Grease filter (6)

For use only with particularly fatty cooking. Hook onto the rear wall of the cavity in front of the fan. It can be washed in the dishwasher and should not be used with the 'Fan' option as the filter will effect the cooking results.

Dehydration rack (7)

To dry any kind of fruit, vegetable and mushrooms.

6

7

4

5

1

2

3

8

Care and Maintenance

Important: Do not use water pressure cleaners or steam cleaners.

Oven exterior and internal frame of the oven

• Clean with a damp cloth. If it is very dirty, add a few drops of washing up liquid to the water. Wipe with a dry cloth.

• Do not use corrosive or abrasive cleaning products, which could dull the surface. If one of these products should accidentally come into contact with the oven, clean it with a damp cloth immediately.

• Slight differences in colour in the front part of the appliance are due to different materials such as glass, plastic and metal being used.

Accessories

• Soak the accessories in water with washing up detergent immediately after use. Food residues can be easily removed using an appropriate brush or a sponge.

Oven cavity

• Do not use abrasive sponges or pan scourers. Use specific cleaning products for ovens and follow the manufacturer’s instructions.

• Leave the oven to cool after each use then clean it to prevent ingrained dirt forming as a result of residue food.

• During prolonged cooking or cooking on several levels, especially in the case of food with a high water content (pizza, stuffed vegetables etc.), condensation can form inside the door and on the seal. When the oven is cool, dry the part inside the door with a cloth or sponge.

• Clean the glass on the door with an appropriate liquid cleaning product.

• The oven door may be removed to facilitate cleaning.

9

Care and Maintenance

Pyrolysis cleaning

This function allows you to eradicate the traces of food produced during the cooking cycles. These traces, burnt at a temperature of approx. 500°C, can be easily removed with a damp sponge once the oven has cooled down.

• You only need to carry out a pyrolytic cleaning when the oven is particularly dirty and not after each use.

• If the oven is installed under a worktop, make sure that the hot plates or rings are not on when carrying out the pyrolytic cycle.

• Prior to starting a pyrolytic cycle, all the accessories and runner grids must be removed from the oven, to avoid ruining them and to maximise the pyrolytic cycle performance itself. Remove the enamelled side panels because their fitted handles could be subject to colour change. Remove them following the instructions in the chapter on “Cleaning runner grids and varnished side panels”.

• To maximise the pyrolytic cleaning results on the door, you should remove the larger splatters with a damp cloth before starting the pyrolytic cycle.

• The pyrolytic cleaning function has two different functions to adapt to any situation:

- an energy saving cycle (EXPRESS PYROLYSIS) with a 25% reduction in energy consumption compared to the standard pyrolysis cycle. If used regularly (every 2 or 3 uses), your oven will always be clean.

- a standard cycle (PYROLYSIS), that guarantees an in-depth clean when the oven is particularly dirty.

• As a safety measure, the oven door seals shut as soon as the

Pyrolytic cycle starts. It is impossible to open the door even if the button is at 0 because of the extremely high temperatures reached inside the oven during the pyrolytic cycle.

• The oven light switches off when the oven reaches a certain internal temperature to prolong its lifespan.

When should a pyrolytic cycle be used?

This function should be used if the oven is smoking when heating up and there is a lot of smoke when cooking, or when there are unpleasant smells when the oven is cold after cooking different kinds of food (lamb, fish, grilled meats, etc.).

COOKING THAT LEAVES LITTLE TRACE OF DIRT

Biscuits, vegetables, cakes, quiches, soufflés. They do not splatter when cooking

COOKING THAT PRODUCES AN AVERAGE AMOUNT OF

DIRT

Meat, fish (in an oven tray), stuffed vegetables.

COOKING THAT PRODUCES A LARGE AMOUNT OF DIRT

Large pieces of meat on a spit or use of the Turbogrill.

10

Care and Maintenance

Warning: use protective gloves for the following operations.

Follow these instructions very carefully to prevent injury and damaging the oven door and hinges.

Make a careful note of the position of the pieces of glass before dismantling it so that you fit them back on again in the right position.

Do not touch the hinges when cleaning and/or removing the door (Fig. 1).

Fig. 1

How to remove the oven door:

• Use protective gloves.

• Open the door fully (see Fig. 2).

• Lift the two catches and push them forward as far as they can go

(see Fig. 3).

• Partially close the door to remove it, lifting it upwards (see Fig. 4).

Fig. 2

To remove the oven door:

• Place the oven door on a flat surface (Fig. 5).

• Slacken the screws on the two glass supports (A) next to the hinges and put them to the side (Fig. 5, Fig. 6).

Fig. 3

Fig. 4

Fig. 5

Fig. 6

11

Instructions for removing the door

• Remove the internal glass by lifting it by the side and removing it from its position (Fig. 7).

• Remove the second and third piece of glass, paying attention to the position of the lettering “REFLECTING SIDE” if present (Fig.

8).

• Follow the reverse procedure to refit the glass:

- the lettering “REFLECTING SIDE” on the intermediate pieces of glass should be positioned so that it is legible;

- if an intermediate piece of glass does not have the lettering

“REFLECTING SIDE”, place it as close as possible to the internal glass.

• Place the internal glass into its position, making sure that the lettering “EASY CLEAN” is facing the upper part of the door (on the plastic profile side).

• Replace and tighten the two glass supports A (Fig. 5 and Fig. 6).

Take particular care with the hinges when cleaning and/or dismantling the door (Fig. 9).

Note: a slight gap between the internal glass and the side posts on the door is normal as this acts as compensation for the glass expanding when hot.

How to remount the door:

• Insert the hinges in their grooves and lower the door fully (Fig. 4).

• Lower the two catches again (Fig. 3).

• Fully close the oven door.

Changing the rear oven lamp bulb

• Disconnect the oven from the electrical supply.

• Let the oven cool before turning the lamp cover left to unscrew it

(see Fig. 10).

• Change the bulb (see note).

• Screw the lamp cover back on.

• Reconnect the oven to the electrical supply.

Note: only use 40 W - 230V lamps, such as E-14, T 300°C, available from the Customer Care Centre.

Important: do not use the oven without replacing the lamp cover.

Fig. 7

Fig. 8

Fig. 9

Fig. 10

12

Troubleshooting guide

Oven not working:

• Make sure there is a power supply and that the oven is connected to the mains supply.

• Turn the oven off and restart it to see if the fault persists.

If the door is blocked:

• Turn the oven off and restart it to see if the fault is repeated.

IMPORTANT:

• Make sure that the oven control knob is not turned to “ 0 ” or to the “lamp” symbol .

- If the electronic programmer is showing “STOP”, consult the separate Product Description Sheet and/or the description of the electronic programmer.

- If the electronic programmer is showing “ F HH ”, contact the Customer Care Centre. In this case, specify the number following the letter “ F ”.

After Sales Service

Before contacting the Customer Care Centre:

1. Try to solve the problem yourself based on the descriptions given in the “Troubleshooting guide”.

2. Turn the appliance off and restart it to see if the fault persists.

If after carrying out the above checks, the fault persists, contact the Customer Care Centre .

Please give:

• a short description of the fault;

• the exact model of the oven;

• the service number (this is the number found after the word

Service on the rating plate), located on the internal edge on the right hand side of the oven opening (visible when the oven door is open). The service number can also be found in the warranty booklet;

• your full address;

• your telephone number.

If repair work has to be carried out, contact the Customer Care

Centre (Use of original spare parts and a proper repair is guarenteed).

Failure to comply with these instructions could compromise the safety and quality of your product.

DECLARATION OF CONFORMITY

• This oven was designed to come into contact with food stuffs and complies with EEC (CE) Regulation n. 1935/2004.

• It was exclusively designed for use as a cooking appliance.

Any other use of the appliances (e.g. heating rooms) is considered improper and subsequently dangerous.

• It was designed, produced and launched onto the market in compliance with:

- safety objectives of the “Low Voltage” Directive

2006/95/CE (which replaces 73/23/CEE and subsequent amendments).

- the safety requirements in the “EMC” Directive

89/336/EEC.

- the requirements of Directive 93/68/EEC.

13

Printed in Italy

02/09

5019 710 02083 n

GB