PRODUCT SHEET
GB
- The internal temperatures of the appliance depend on the ambient temperature, frequency of opening the doors, as well as location of the appliance. Temperature setting must consider these factors.
- The appliance accessories are not suitable for washing in dishwasher.
A. Refrigerator Compartment
2.
Lighting
3.
Shelves / Shelf area
4.
Multi-flow cold air system
5.
Cooler compartment
6.
Rating plate with commercial name
8.
Crisper divider
9.
Reversibility kit
10.
Egg tray
11.
Separator
12.
Door trays
13.
Storage baskets for frozen food items
13a.
“Eco green” basket (only in models with ECO
GREEN function)
14.
Shelves
15.
Bottom basket (freezing zone)
16.
Ice tray and/or cold accumulator
18.
The freezer door trays for pizza or other frozen products with a short storage time
Depending on the model the number and type of accessories may vary.
The freezer compartment can be used without the two upper baskets to increase storage for large products. The lower basket must not be removed.
Place the food products directly on the racks.
After inserting food, ensure that the freezer compartment door closes properly.
C. Control panel
Anti-bacterial protection :
1.
Filter in fan (depending on the model)
7.
Crisper with antibacterial additives (depending on the model)
17.
Door seals
The crisper and the door seals are manufactured from materials that inhibit bacterial growth.
Notes:
- In case of power failure the cold accumulator helps to keep optimal storage temperature longer.
- All shelves and door trays are removable.
FAN WITH A BUTTON
The fan gives more even temperature distribution inside the refrigerator compartment, allowing better preservation of stored food.
To switch on the fan press the button ( 1a ). It is advisable to activate the fan when the ambient air temperature is over 27 ÷ 28°C or if you perceive drops of water on the glass shelves or in the severe humidity conditions.
Note:
Do not obstruct the air intake area with food items.
The fan will run ONLY when the compressor is in operation.
Remember to turn off the fan when there is a lower ambient air temperature.
If the appliance has the fan it can be equipped with the antibacterial filter.
Remove it from the box (found in the crisper drawer
(item 7 ) and insert into the cover of fan (item 1b ).
The replacement procedure is attached with the filter.
HOW TO START THE APPLIANCE
After plugging the appliance to the mains, it starts the operation automatically. The indicator lamps on the control panel light up for approximately 1 second, and after initialization process, setpoint is displayed.
Note: if food is placed in the refrigarator before the appliance has cooled completely, it may deteriorate.
If fresh food is loaded in freezer position 3 on control panel should be chosen.
CONTROL PANEL DESCRIPTION
1.
extra low temperature
2.
low temperature
3. "ECO GREEN" position (depending on the model)
4.
high temperature
5.
temperature selection/stand-by (3 sec.) pushbutton
6.
internal light switch
OPERATION DESCRIPTION
Temperature adjustment is made with pushbutton ( 5 ).
Temperature setpoint is done for both compartments at one time – fridge and freezer.
D GB F NL E P I GR S N DK FIN PL CZ SK H RUS BG RO
high temperature low temperature extra low temperature
PRODUCT SHEET
At first plug-in of appliance factory setpoint is chosen – medium position (ECO Green, depending on model).
Following table shows set-points level
GB
ABNORMAL APPLIANCE OPERATION
When the product is plugged in to the mains, during first
10 minutes of its performance, possible temperature sensor failure will be displayed according to following table:
Refrigerator sensor failure
Freezer sensor failure
Refrigerator freezer sensor failure
Description Lamp OFF Lamp Flashing
Description Lamp OFF Lamp ON
The appliance will work preserving the food stored, but it is necessary to contact after-sales service and provide alarm code.
GUIDE TO SELECTING FUNCTIONS
Temperature selection / stand-by pushbutton is used to set desired temperature level, from warmest through lower to coldest . Pressing pushbutton setpoint will change cyclically.
Stand-by / ON function
To put the appliance in Stand-by state press and hold
Temperature selection / stand-by pushbutton for 3 seconds.
Note: When the product is in stand-by mode the light operates normally, all other loads are disabled and control panel shows no indication. When the appliance has to be left for a longer period with fridge door open to avoid odour, power cord has to be unplugged from the power supply.
To switch on the product when it is in Stand-by state, press Temperature selection / stand-by pushbutton for 3 seconds.
Appliance comes back to normal operation, control panel displays previously chosen setpoint.
Note: in case of power failure, appliance goes back to normal operation and previously chosen setpoint is restored.
ECO GREEN function
This function gives best food preservation performance with the smallest energy consumption possible (around 5-
10% less in comparison with the normal settings) if there is lower amount of food to be preserved in the appliance.
The best food preservation conditions when ECO function is activated are in the ECO compartments:
- 2 “eco green” shelves in the fridge (with green frames)
- 1 “eco green” basket in freezer compartment.
DEFROSTING THE FREEZER
COMPARTMENT
Whirlpool No Frost freezers provide chilled air circulation around the storage areas and prevent the formation of ice, thereby completely eliminating the need for defrosting. Frozen items don't stick to the walls, labeling stays legible and storage space remains neat and clear.
DEFROSTING THE REFRIGERATOR
COMPARTMENT
Refrigerator compartment defrosting is completely automatic.
Droplets of water on the rear wall inside the refrigerator compartment indicate that the automatic defrost phase is in progress. The defrost water is automatically run into a drain hole and collected in a container, where it evaporates.
REPLACING THE LIGHT BULB
Always disconnect the refrigerator from the power supply before replacing any light bulb.
If the inside light is not working, it is necessary to:
1.
Remove the light cover: put the fingers into the side ventilation holes ( 1 ), stretch the cover gently and move it upwards.
2.
Check the bulb. If necessary unscrew the broken bulb and replace it with the new one (use maximum 15W bulb).
3.
Put on the light cover.
Do not leave the bulb uncovered.
D GB F NL E P I GR S N DK FIN PL CZ SK H RUS BG RO
