Imagine communications Selenio 6800 Installation And Operation Manual
Oglas
Oglas
Installation and Operation Manual
Selenio 6800™
HMX6803+ & OP+HMX+
8-AES Audio Multiplexer &
8-AES Audio Multiplexer with Fiber Output
Edition
E
175-100062-00
Delivering the Moment
Publication Information
© 2014 Imagine Communications Corp. Proprietary and Confidential.
Imagine Communications considers this document and its contents to be proprietary and confidential.
Except for making a reasonable number of copies for your own internal use, you may not reproduce this publication, or any part thereof, in any form, by any method, for any purpose, or in any language other than English without the written consent of Imagine Communications. All others uses are illegal.
This publication is designed to assist in the use of the product as it exists on the date of publication of this manual, and may not reflect the product at the current time or an unknown time in the future. This publication does not in any way warrant description accuracy or guarantee the use for the product to which it refers. Imagine Communications reserves the right, without notice to make such changes in equipment, design, specifications, components, or documentation as progress may warrant to improve the performance of the product.
Trademarks
6800+™, ADC™, CCS Navigator™, Channel ONE™, ChannelView™, ClipSync™, Delay™, D Series™, D Series DSX™, Deliver the Moment™, Delivering the Moment™, FAME™, Farad™, G8™, G Scribe™, HView™,
IconMaster™, IconLogo™, IconStation™, IconKey™, InfoCaster™, InfoCaster Creator™, InfoCaster Manager™, InfoCaster Player™, InstantOnline™, Invenio®, Live Update™, mCAPTURE™, Magellan™, Magellan CCS
Navigator™, Magellan Q SEE™, MultiService SDN™, NetPlus™, NetVX™, NewsForce™, Nexio® G8™, Nexio
AMP® ChannelView™, Nexio® Channel ONE™, Nexio® ClipSync™, Nexio® Delay™, Nexio® Digital Turnaround
Processor™, Nexio® Farad™, Nexio® G Scribe™, Nexio® IconKey™, Nexio® IconLogo™, Nexio® IconMaster™,
Nexio® IconStation™, Nexio® InfoCaster™, Nexio® InfoCaster Creator™, Nexio® InfoCaster Manager™,
Nexio® InfoCaster Player™, Nexio® InfoCaster Traffic™, Nexio® InstantOnline™, Nexio® mCAPTURE™, Nexio®
NewsForce™, Nexio® NXIQ™, Nexio® Playlist™, Nexio® Remote™, Nexio®RTX Net™, Nexio® TitleMotion™,
Nexio® TitleOne™, Nexio® Velocity ESX™, Nexio® Velocity PRX™, Nexio® Velocity XNG™, Nexio® Volt™,
OPTO+™, Panacea™, Platinum™, Playlist™, Predator II GRF™, Predator II GX™, Punctuate™, Remote™, RTX
Net™, QuiC™, Q SEE™, SD STAR™, Selenio™, Selenio 6800+™, SelenioNext™, Selenio X50™, Selenio X85™,
Selenio X100™, TitleMotion™, TitleOne™, Velocity ESX™, Velocity PRX™, Velocity XNG™, Versio™,
Videotek® SD STAR™, X50™, and X85™ are trademarks of Imagine Communications or its subsidiaries.
Altitude Express®, Connectus®, Enabling PersonalizedTV®, ICE® Broadcast System, ICE Illustrate®,
ICE Q® algorithms, ICEPAC®, Imagine ICE®, Inscriber®, Inscriber® Connectus®, Invenio®, NEO®, Nexio®,
Nexio AMP®, PersonalizedTV®, RouterWorks®, Videotek®, Videotek® ASI STAR®, Videotek® GEN STAR®, and Videotek® HD STAR® are registered trademarks of Imagine Communications or its subsidiaries.
Microsoft® and Windows® are registered trademarks of Microsoft Corporation. HD BNC is a trademark of
Amphenol Corporation. Some products are manufactured under license from Dolby Laboratories. Dolby and the double D symbol are registered trademarks of Dolby Laboratories. DTS Neural audio products are manufactured under license from DTS Licensing Limited. DTS and the Symbol are registered trademarks & the DTS Logos are trademarks of DTS, Inc. © 2008 2010 DTS, Inc. All other trademarks and trade names are the property of their respective companies.
Contact Information
Imagine Communications has office locations around the world. For locations and contact information see:
http://www.imaginecommunications.com/contact us/
Support Contact Information
For support contact information see:
▪ Support Contacts:
http://www.imaginecommunications.com/services/technical support/
▪ eCustomer Portal:
http://support.imaginecommunications.com
© 2014 Imagine Communications Corp. Proprietary and Confidential
HMX6803+
8-AES Audio Multiplexer
OP+HMX+
8-AES Audio Multiplexer
With Fiber Output
Installation and Operation Manual
Edition F
April 2013
Contents
Preface
........................................................................................................................ vii
Safety Standards and Compliances
............................................................................. xi
Restriction on Hazardous Substances (RoHS) Compliance ........................................... xi
Waste from Electrical and Electronic Equipment (WEEE) Compliance .......................... xi
Chapter 1 Introduction
.............................................................................................................. 1
....................................................................................................... 1
HMX + Module Types ........................................................................................... 2
..................................................................................................... 3
.................................................................................................................. 10
Chapter 2 Installation
............................................................................................................. 11
............................................................................................... 11
iii
iv Contents
and OP + HMX + Upgrade Options ............................................ 12
........................................................................................................... 13
Ω /Hi-Z Input Impedance Control ......................................... 13
+ Frame Power Ratings ...................................................................... 14
+ Modules ............................................................................................ 15
Installing and Removing HMX6803
+ Modules .......................................................... 15
+ HMX + Modules ................................................................................... 16
Chapter 3 Operation
.................................................................................................................. 21
..................................................................................... 21
and OP + HMX + Functions ....................................................... 21
Cross-Functional Parameter Changes
......................................................................... 32
Changing Parameter Settings Using Card-Edge Controls .......................................... 36
+ Remote Control Parameters ....................................................... 38
.......................................................................................................... 57
HMX6803
+
and OP
+
HMX
+
Installation and Operation Manual v
Chapter 4 Specifications
........................................................................................................ 63
Analog Audio Input (Analog Audio Enabled Modules Only) ..................................... 65
+ HMX + Only) ................................................................................... 66
HMX + Only) ..................................................................................... 67
............................................................................................................. 68
...................................................................................................... 68
.............................................................................................................. 69
.............................................................................................. 69
Appendix A Audio Bit Manipulation
.................................................................................... 71
Manipulating Validity and User Bits (V-Bit and U-Bit)
.............................................. 74
Identifying Audio Characteristics
(Audio Sampling Frequency and Word Length)
........................................................ 75
Appendix B Laser Safety Guidelines
.................................................................................... 77
................................................................................................................. 77
Appendix C Communication and Control Troubleshooting Tips
............................. 79
Software Communication Problems
.......................................................................... 79
Index
........................................................................................................................... 83
vi Contents
Preface
Manual Information
Purpose
This manual details the features, installation, operation, maintenance, and specifications for the HMX6803
+
and OP
+
HMX
+
auto-sensing SD/HD-SDI 8-AES audio demultiplexers.
Audience
This manual is written for engineers, technicians, and operators responsible for installation, setup, maintenance, and/or operation of the HMX6803
+
and OP
+
HMX
+ auto-sensing SD/
HD-SDI 8-AES audio demultiplexers.
Revision
History
Table P-1 Revision History of Manual
D
E
F
B
C
Edition Date
A April 2009
June 2009
Comments
Initial release
Additional AFD feature set
September 2010 Addition of level-B support
January 2012
January 2013
April 2013
Addition of analog audio submodule and features
Minor elucidation of Input Audio Level specification
Update signal flow diagram and add parameters from firmware version 1.10 vii
viii Preface
Writing
Conventions
To enhance your understanding, the authors of this manual have adhered to the following text conventions:
Table P-2 Writing Conventions
Term or
Convention
Bold
Description
Italics
Indicates dialog boxes, property sheets, fields, buttons, check boxes, list boxes, combo boxes, menus, submenus, windows, lists, and selection names
Indicates E-mail addresses, the names of books or publications, and the first instances of new terms and specialized words that need emphasis
CAPS
Code
Indicates a specific key on the keyboard, such as ENTER, TAB, CTRL,
ALT, or DELETE
Indicates variables or command-line entries, such as a DOS entry or something you type into a field
> hyperlink
Indicates the direction of navigation through a hierarchy of menus and windows
Indicates a jump to another location within the electronic document or elsewhere
Internet address Indicates a jump to a website or URL
Indicates important information that helps to avoid and troubleshoot problems
Obtaining
Documents
Product support documents can be viewed or downloaded from our website. Alternatively, contact your Customer Service representative to request a document.
Unpacking/Shipping Information
Unpacking a
Product
This product was carefully inspected, tested, and calibrated before shipment to ensure years of stable and trouble-free service.
1 Check equipment for any visible damage that may have occurred during transit.
2 Confirm that you have received all items listed on the packing list.
3 Contact your dealer if any item on the packing list is missing.
4 Contact the carrier if any item is damaged.
5 Remove all packaging material from the product and its associated components before you install the unit.
Keep at least one set of original packaging, in the event that you need to return a product for servicing.
HMX6803
+
and OP
+
HMX
+
Installation and Operation Manual ix
Product
Servicing
Except for firmware upgrades, HMX6803
+
and OP
+
HMX
+
modules are not designed for field servicing. All hardware upgrades, modifications, or repairs require you to return the modules to the Customer Service center.
Returning a
Product
In the unlikely event that your product fails to operate properly, please contact Customer
Service to obtain a Return Authorization (RA) number, and then send the unit back for servicing.
Keep at least one set of original packaging in the event that a product needs to be returned for service. If the original package is not available, you can supply your own packaging as long as it meets the following criteria:
The packaging must be able to withstand the product’s weight.
The product must be held rigid within the packaging.
There must be at least 2 in. (5 cm) of space between the product and the container.
The corners of the product must be protected.
Ship products back to us for servicing prepaid and, if possible, in the original packaging material. If the product is still within the warranty period, we will return the product prepaid after servicing.
References
ANSI/SMPTE 259M-1997
10-Bit 4:2:2 Component and 4fsc NTSC Composite Digital Signals - Serial Digital Interface
ITU-R BT.601-5
Studio Encoding Parameters of Digital Television for Standard 4:3 and Wide-Screen 16:9
Aspect Ratios
SMPTE 292M-1999
Bit-Serial Digital Interface for High-Definition Television Systems
ITU-R BT.709-4
Parameter Values for the HDTV Standards for Production and International Programme
Exchange
SMPTE 291M-1998
Ancillary Data Packet and Space Formatting
SMPTE RP 184-1996
Specification of Jitter in Bit-Serial Digital Systems
ANSI/SMPTE 276M-1995
Transmission of AES/EBU Digital Audio Signal Over Coaxial Cable
x Preface
AES3-2003
AES Recommended Practice for Digital Audio Engineering - Serial Transmission Format for
Two-Channel Linearly Represented Digital Audio Data
TIA/EIA-232-E 1991
Interface Between Data Terminal Equipment and Data Circuit-Terminating Equipment
Employing Serial Binary Data Interchange
EIA/TIA-422-B 1994
Electrical Characteristics of Balanced Voltage Digital Interface Circuits
EIA RS-485 1983
Standard for Electrical Characteristics of Generators and Receivers for use in Balanced
Digital Multipoint Systems
SMPTE 346-M 2000
Time Division Multiplexing Video Signals and Generic Data over High-Definition Interface
SMPTE 352-M 2002
Video Payload Identification for Digital Interfaces
SMPTE 424-M 2005 (Proposed)
3Gb/s Signal/Data Serial Interface
SMPTE 425-M 2005 (Proposed)
3Gb/s Signal/Data Serial Interface - Source Image Format Mapping
47 Code of Federal Regulations
Part 15 FCC rules—Radio Frequency Devices
EN55103-1
EMC emission requirements applies to professional audio, video, audio-visual and entertainment lighting control apparatus
EN55103-2
EMC immunity requirements applies to professional audio, video, audio-visual and entertainment lighting control apparatus
IEC 61754-4
Specifications for the fiber optic connector type SC/PC
IEC 61754-2
Specifications for the fiber optic connector type ST/PC terminated to a type BFOC/2,5
IEC 61754-13
Specifications for the fiber optic connector type FC/PC
HMX6803
+
and OP
+
HMX
+
Installation and Operation Manual xi
Safety Standards and Compliances
See Laser Safety on page 77 to find the safety standards and compliances for this OPTO
+ series product. A 6800
+ series safety manual is shipped with every 6800
+
Frame
Installation and Operation Manual and can be downloaded from our website. Alternatively, contact your Customer Service representative for a copy of this safety manual.
Restriction on Hazardous Substances (RoHS) Compliance
Directive 2002/95/EC—commonly known as the European Union (EU) Restriction on
Hazardous Substances (RoHS)—sets limits on the use of certain substances found in electrical and electronic equipment. The intent of this legislation is to reduce the amount of hazardous chemicals that may leach out of landfill sites or otherwise contaminate the environment during end-of-life recycling. The Directive, which took effect on July 1, 2006, refers to the following hazardous substances:
Lead (Pb)
Mercury (Hg)
Cadmium (Cd)
Hexavalent Chromium (Cr-V1)
Polybrominated Biphenyls (PBB)
Polybrominated Diphenyl Ethers (PBDE)
According to this EU Directive, all products sold in the European Union will be fully
RoHS-compliant and “lead-free.” (See our website for more information on dates and deadlines for compliance.) Spare parts supplied for the repair and upgrade of equipment sold before July 1, 2006 are exempt from the legislation. Equipment that complies with the
EU directive will be marked with a RoHS-compliant emblem, as shown in Figure 1 .
Figure P-1 RoHS Compliance Emblem
Waste from Electrical and Electronic Equipment (WEEE) Compliance
The European Union (EU) Directive 2002/96/EC on Waste from Electrical and Electronic
Equipment (WEEE) deals with the collection, treatment, recovery, and recycling of electrical and electronic waste products. The objective of the WEEE Directive is to assign the responsibility for the disposal of associated hazardous waste to either the producers or users of these products. As of August 13, 2005, the producers or users of these products were required to recycle electrical and electronic equipment at end of its useful life, and may not dispose of the equipment in landfills or by using other unapproved methods. (Some EU member states may have different deadlines.)
xii Preface
In accordance with this EU Directive, companies selling electric or electronic devices in the
EU will affix labels indicating that such products must be properly recycled. (See our website for more information on dates and deadlines for compliance.) Contact your local Sales representative for information on returning these products for recycling. Equipment that complies with the EU directive will be marked with a WEEE-compliant emblem, as shown in
.
Figure P-2 WEEE Compliance Emblem
Safety Terms and Symbols in this Manual
This product manual uses the following safety terms and symbols to identify certain
conditions or practices. See Laser Safety on page 77 and the
FR6802
+
Safety Instructions and Standards Manual for more information.
WARNING
Statements identifying conditions or practices that may result in personal injury or loss of life. High voltage is present.
CAUTION
Statements identifying conditions or practices that can result in damage to the equipment or other property.
1
Introduction
Product Description
The HMX6803
+
is an auto-sensing SD/HD-SDI 4-AES audio multiplexer and processing amplifier with one digital video input and one DARS reference input, and has four processed
SD/HD-SDI outputs. The OP
+
HMX
+
module has the same features, and an additional optical transmitter. The modules support embedding and passing of Dolby E™ metadata, and picture and sound control through integrated processing amplifiers. The basic HMX6803
+ and OP
+
HMX
+
provide SD and HD-SDI audio embedding, and there is an optional upgrade to 3G HD-SDI (including dual-link). Another optional upgrade adds four AES inputs, for a total of eight.
Each HMX6803
+
or OP
+
HMX
+
package includes a module-specific breakout cable with unbalanced (coaxial) audio connectors that expands the number of available connections beyond what would fit on a standard two-slot back connector. Balanced AES inputs are supported with external baluns. The breakout cable includes an RS-232/RS-422 serial connector to embed metadata.
HMX6803
+
and OP
+
HMX
+
can be operated locally (using card-edge controls); or operated and monitored remotely with control software applications such as CCS Navigator
™
, HTTP web browser, third-party SNMP-based control applications, or CCS-compliant remote control panels such as NUCLEUS. The modules are QSEE™-compliant, so you can monitor a thumbnail when it is installed in an Ethernet-equipped FR6802
+
QXF or FR6822
+
frame.
The HMX6803
+
and OP
+
HMX
+
back connector requires two frame slots within an
FR6802
+
XF, FR6822
+
, or FR6802
+
QXF frame. The HMX6803
+
AI
+
T and OP
+
HMX
+
AI
+
T require three slots within the same frames. There is no backward compatibility provided for use with 6800/7000 series frames or FR6802
+
DM frames. HMX6803
+
and OP
+
HMX
+
must be installed in a frame with fans.
Main
Features
All versions of HMX6803
+
and OP
+
HMX
+
include the following features:
Inputs
One serial digital SMPTE 292M/SMPTE 259M SDI input
Metadata
Four AES audio
DARS input (unbalanced, balanced compatible with external balun)
Outputs
Four serial digital SMPTE 292M/259M SDI processed outputs
One RS-232/RS-422 serial connector to embed metadata
1
2 Chapter 1
Introduction
10-bit video processing in the following standards and frame rates:
Standard definition 525/625
1080psf (progressive segmented frame), 23.98/24 Hz
1080i (interlaced), 25/29.97/30 Hz
1080p (progressive), 23.98/24/25/29.97/30 Hz
720p (progressive), 50/59.94/60 Hz
Up to 50 frames of SD video delay, up to 11 frames of HD video delay
Auto-detect or user-forced input video standard with HD/SD-SDI auto sensing
AFD/WSS/VI detector and inserter
Seamless sound functionality
V-fading of the output audio on source audio change
Automatic cable equalization
Embed on black or grey on loss of video mode
Video processing amplifier with luminance gain/offset and chrominance gain/offset controls
16-, 20-, or 24-bit audio processing
Shadowed/restored parameter settings when switching video standards
Card-edge control and monitoring
Serial and Ethernet remote control and monitoring
Video and audio test signal generators
Optional
Features
OP
+
HMX
+
has an optional fiber transmitter.
HMX68OPT
+
AES8 adds four balanced or unbalanced AES inputs, for a total of eight.
The HMX68OPT
+
3G upgrade option adds 10-bit video processing with 1080p (progressive) video standard at 50/59.94/60 Hz frame rates as per SMPTE 424M and dual-link as per
SMPTE 372M (data and audio embed/de-embed is fixed on link A).
HMX6803
+
AI
+
T and OP
+
HMX
+
AI
+
T add analog audio inputs.
OP
+
HMX
+
Module
Types
describes the different versions of the OP
+
HMX
+
product. The basic module outputs through an SC/PC connector. Hardware upgrade options are listed in
.
Table 1-1 OP
+
HMX
+
Modules
Description Module Name
OP
+
HMX
+
13D
OP
+
HMX
+
CxxD
Fiber transmitter set at 1310 nm
Fiber transmitter set at CWDM wavelength of 1xx0 nm
OP
+
HMX
+
AI
+
13T Fiber transmitter set at 1310 nm with analog audio inputs
OP
+
HMX
+
AI
+
CxxT Fiber transmitter set at CWDM wavelength of 1xx0 nm with analog audio inputs
HMX6803
+
and OP
+
HMX
+
Installation and Operation Manual
3
Hardware
Options
All OP
+
HMX
+
modules are shipped with standard SC/PC fiber connectors. Other connectors are available (see
).
Table 1-2 Available Connectors
Item
OP
+
OPT
+
SC
OP
+
OPT
+
ST
OP
+
OPT
+
FC
Description
SC/PC fiber optic connectors (standard)
ST/PC fiber optic connectors (optional)
FC/PC fiber optic connectors (optional)
Module Descriptions
HMX6803
+
and OP
+
HMX
+
hardware versions have minor variances in their specifications,
which are listed in Chapter 4, Specifications on page 63.
To determine which specifications apply to your module, see
Front Module
is a generic top-front view of a typical 6800
+
module and shows the general location of standard LEDs, controls, and jumpers. The number of control and monitoring
LEDs on 6800
+
modules varies.
Remote/local control
Modul e status
Mode select rotary
Navigation toggle
Control
LEDs
Figure 1-1 Typical 6800
+
Module
Monitoring
LEDs
Extractor handle
Table 1-3 on page 4 briefly describes generic 6800
+
LEDs, switches, and jumpers. See
Chapter 3, Operation for more information on specific HMX6803
+
and OP
+
HMX
+ module controls, LEDs, and jumpers.
4 Chapter 1
Introduction
Table 1-3 Generic 6800
+
Module Features
Feature Description
Module status
LEDs
Mode select rotary switch
Navigation toggle switch
Various color and lighting combinations of these LEDs indicate the module state. See information.
Monitoring LEDs on page 57 for more
This switch selects between various control and feedback parameters.
Control LEDs
Monitoring
LEDs
Local/remote control jumper
This switch navigates up and down through the available control parameters:
Down : Moves down through the parameters
Up : Moves up through the parameters
Various lighting combinations of these control LEDs
(sometimes referred to as “Bank Select LEDs”) indicate which
Each 6800
+
module has a number of LEDs assigned to indicate varying states/functions. See
Monitoring LEDs on page 57 for a description of these LEDs.
Local : This jumper setting locks out external control panels and allows card-edge control only; limits the functionality of remote software applications to monitoring
Remote : This jumper setting allows remote or local
(card-edge) configuration, operation, and monitoring of the HMX6803
+
and OP
+
HMX
+
(this is the default setting)
Back
Connectors
Figure 1-2 shows the double-slot back connector used by HMX6803
+
and OP
+
HMX
+ modules.
HMX6803
+
and OP
+
HMX
+
Installation and Operation Manual
5
Fiber SDI IN 1
SDI OUT 1
SDI OUT 2
SDI OUT 3
SDI OUT 4
HMX6803+
HDX6803+
SFS6803+
OP+HMX+
OP+HDX+
OP+SFS+
SDI IN
1
2
3
4
Two-slot back connector for
HMX6803
+
and OP
+
HMX
+
Three-slot back connector for
HMX6803
+
AO
+
T and
OP
+
HMX
+
AO
+
T
Figure 1-2 HMX6803
+
and OP
+
HMX
+
Back Connector
Note: To maintain optimal output video signal integrity, terminate unused output video
BNCs with 75
Ω
terminators.
Breakout
Cables
The standard HMX6803
+
and OP
+
HMX
+
ship with an unbalanced breakout cable, pictured
. For information on ordering cables, see Table 2-1 on page 11.
If you need to make your own breakout cable, pinouts are listed in
, and pin
numbers for the 44-pin connector are listed in Figure 1-4 on page 7.
6 Chapter 1
Introduction
AES1 IN
AES2 IN
AES3 IN
AES4 IN
AES5 IN
AES6 IN
AES7 IN
AES8 IN
AES1 OUT
AES2 OUT
AES3 OUT
AES4 OUT
AES5 OUT
AES6 OUT
AES7 OUT
AES8 OUT
AES 1 In
AES 2 In
AES 3 In
AES 4 In
AES 5 In
AES 6 In
AES 7 In
AES 8 In
AES 1 Out
AES 2 Out
AES 3 Out
AES 4 Out
AES 5 Out
AES 6 Out
AES 7 Out
AES 8 Out
DARS IN
DATA I/O
DARS In
Data I/O
Genlock (not used with HMX6803
+
and OP
+
HMX
+
)
GENLOCK
SERIAL Serial
Figure 1-3 HMX6803
+
and OP
+
HMX
+
Breakout Cable
HMX6803
+
and OP
+
HMX
+
Installation and Operation Manual
7
Figure 1-4 Pin Numbers for 44-Pin Connector
Table 1-4 Pinouts for 44-Pin Connector
27
28
29
30
24
25
25
26
15
16
17
18
19
20
21
22
23
11
12
13
14
7
8
9
10
5
6
3
4
1
2
Pin No. on
DB-44M
Connection Type
BNC
BNC GND
BNC GND
BNC
BNC GND
BNC
BNC GND
BNC
BNC GND
BNC
BNC GND
BNC
BNC GND
BNC GND
BNC
Not Connected
BNC
BNC
BNC GND
BNC
BNC GND
BNC
Description
GENLOCK
GENLOCK GND
AES OUT 7 GND
AES IN 4
AES IN 4 GND
AES IN 3
AES IN 3 GND
DATA IO
DATA IO GND
AES OUT 2
AES OUT 2 GND
AES OUT 1
AES OUT 1 GND
AES IN 7 GND
AES IN 7
AES OUT 7
DARS IN 1
DARS IN 1 GND
AES IN 2
AES OUT 3 GND
AES OUT 3
BNC GND AES OUT 6 GND
162A10019X (DB9.5) RS232_GND (DB9)
BNC GND
BNC
AES OUT 4 GND
AES OUT 4
BNC GND
BNC
BNC GND
BNC GND
AES OUT 5 GND
AES IN 8
AES IN 8 GND
AES IN 5 GND
AES OUT 7
DARS IN 1
DARS IN 1
AES IN 2
AES OUT 3
AES OUT 3
AES OUT 6
SERIAL
AES OUT 4
AES OUT 4
AES OUT 5
AES IN 8
AES IN 8
AES IN 5
Wire Label
GENLOCK
GENLOCK
AES OUT 7
AES IN 4
AES IN 4
AES IN 3
AES IN 3
DATA IO
DATA IO
AES OUT 2
AES OUT 2
AES OUT 1
AES OUT 1
AES IN 7
AES IN 7
Blue
Yellow
Yellow
White
Blue
Blue
Blue
Black
Blue
Blue
Blue
White
White
White
White
Yellow
Yellow
Blue
Blue
Blue
Blue
White
White
External
Cable Color
Black
Black
Blue
White
White
White
White
Yellow
Yellow
Blue
Blue
Blue
Blue
White
White
BNC
Color
Black
Black
Blue
White
White
White
Blue
Black
Black
White
Blue
Blue
Blue
N/A
Blue
Blue
Blue
White
White
White
8 Chapter 1
Introduction
41
42
43
44
36
37
37
38
39
33
34
35
35
Table 1-4 Pinouts for 44-Pin Connector (Continued)
Pin No. on
DB-44M
31
Connection Type Description
32
40
Wire Label
162A10019X (DB9.3) BALANCED SERIAL IN-
(DB9)
SERIAL
162A10019X (DB9.8) BALANCED SERIAL
IN+ (DB9)
SERIAL
BNC GND
BNC
AES OUT 8 GND
AES OUT 8
AES OUT 8
AES OUT 8
162A10019X (DB9.1) RS422_FR_GND (DB9) SERIAL
BNC GND AES IN 2 GND AES IN 2
BNC AES IN 1 AES IN 1
162A10019X (DB9.9) RS422_FR_GND (DB9) SERIAL
BNC GND
BNC
AES IN 1 GND
AES OUT 6
AES IN 1
AES OUT 6
162A10019X (DB9.7) BALANCED SERIAL
OUT- (DB9)
162A10019X (DB9.2) BALANCED SERIAL
OUT+ (DB9)
SERIAL
SERIAL
BNC
BNC GND
BNC
BNC
AES OUT 5
AES IN 6 GND
AES IN 6
AES IN 5
AES OUT 5
AES IN 6
AES IN 6
AES IN 5
External
Cable Color
Red
Yellow
Blue
Blue
Black
White
White
Black
White
Blue
Blue
Green
Blue
White
White
White
BNC
Color
N/A
N/A
N/A
Blue
White
White
White
Blue
Blue
N/A
White
White
N/A
White
Blue
N/A
RS-422/232
Cable
Figure 1-5 Pin Numbers for RS-422/232 Female Connector
Table 1-5 Pin Assignment of DB-9 Connector (Female) in RS-422 Format
8
3
2
7
4
6
9
5
Pin No.
1
Signal
FG
FG
FG
TA (Tx-)
TB (Tx+)
RA (Rx-)
RB (Rx+)
Not connected
Comments
Frame Ground
Frame Ground
Frame Ground
Transmitted Data -
Transmitted Data +
Received Data -
Received Data +
HMX6803
+
and OP
+
HMX
+
Installation and Operation Manual
9
Table 1-6 Pin Assignment of DB-9 Connector (Female) in RS-232 Format
Pin No.
1
9
5
8
3
2
7
4
6
Signal
FG
FG
FG
Tx
Not connected
Rx
Not connected
Comments
Frame Ground
Frame Ground
Frame Ground
Transmitted Data
Received Data
Weidmuller Connector for Analog Audio Inputs
The HMX6803
+
AI
+
T and OP
+
HMX
+
AI
+
T back modules have an additional connector. It has has the following connections:
Pin 1
Figure 1-6 Analog Audio Connector Pinouts
Table 1-7 Analog Audio Pinouts
5
6
3
4
1
2
Pin
Number
Signal
CH1A+
CH1B+
GND
CH2A+
CH2B+
GND
15
16
17
18
Pin
Number
13
14
Signal
CH1A-
CH1B-
GND
CH2A-
CH2B-
GND
Comments
Input 1
Input 2
10 Chapter 1
Introduction
Table 1-7 Analog Audio Pinouts (Continued)
9
10
11
12
7
8
Pin
Number
Signal
CH3A+
CH3B+
GND
CH4A+
CH4B+
GND
Pin
Number
19
20
21
22
23
24
Signal
CH3A-
CH3B-
GND
CH4A-
CH4B-
GND
Comments
Input 3
Input 4
Signal Flow
3G/HD/SD-SDI
Stereo analog audio in
HMX6803+AI+T
AES In
4
A
B
8
Equalizer
AFD/WSS/VI
Detector
Test pattern generator
Video
Delay
Sample rate converter
Audio delay
Audio proc amp
Laser
Driver
Driver
2
Driver
2
OP+SFS+(C)xxD
3G/HD/SD-SDI
3G/HD/SD-SDI
DARS
Metadata
DARS
Metadata router
CCS
&
QSEE monitoring control
&
CCS & SNMP control
1
Available via breakout cable (included).
Figure 1-7 HMX6803
+
and OP
+
HMX
+
Signal Flow Diagram
Note: 3G HD-SDI in and out are only available if your module has the optional
HMX68OPT
+
3G license key.
2
Installation
Unpacking the Module
Before you install modules, perform the following:
Check the equipment for any visible damage that may have occurred during transit.
Confirm receipt of all items on the packing list. See
for more information.
Note: Contact your Customer Service representative if parts are missing or damaged.
Remove the anti-static shipping pouch, if present, and all other packaging material.
Retain the original packaging materials for possible re-use.
See Unpacking/Shipping Information on page viii for information about returning a
product for servicing.
Checking the
Packing List
Table 2-1 Available Product Packages
Ordered Product Content Description
HMX6803
+
D One HMX6803
+
front module
One double-slot back connector
OP
+
HMX
+
D
One 6800
+
OPT
+
16CAPM breakout cable with unbalanced audio connectors
One HMX6803
+
and OP
+
HMX
+
Installation and Operation
Manual
One OP
+
HMX
+
front module
One double-slot back connector
One 6800
+
OPT
+
16CAPM breakout cable with unbalanced audio connectors
One HMX6803
+
and OP
+
HMX
+
Installation and Operation
Manual
11
12 Chapter 2
Installation
Table 2-1 Available Product Packages (Continued)
Ordered Product Content Description
HMX6803
+
AI
+
T One HMX6803
+
front module with submodule providing eight mono or four stereo analog audio inputs
OP
+
HDX
+
AI
+
T
One triple-slot back connector
One 6800
+
OPT
+
16CAPM breakout cable with unbalanced audio connectors
One HMX6803
+
and OP
+
HMX
+
Installation and Operation
Manual
One OP
+
HMX
+
front module with submodule providing eight mono or four stereo analog audio inputs
One triple-slot back connector
One 6800
+
OPT
+
16CAPM breakout cable with unbalanced audio connectors
One HMX6803
+
and OP
+
HMX
+
Installation and Operation
Manual
6800
+
OPT
+
16CAPM One breakout cable with unbalanced audio connectors
Choosing HMX6803
+
and OP
+
HMX
+
Upgrade Options
Basic HMX6803
+
and OP
+
HMX
+
modules have one SD-SDI input and four SD-SDI outputs with embedded audio. The following firmware upgrades are available:
Table 2-2 Available License Key Upgrades
Ordered Product
HMX68OPT-AES8
HMX68OPT-3G
Content Description
Adds four discrete AES inputs, for a total of eight
Adds 3G HD-SDI and Level B functionality to an 1.5G HD-SDI and SD-SDI module
To purchase additional license keys, contact your Sales representative. To activate a license key, see
Adding a License Key on page 22.
Selecting an
External
Balun
The following baluns from Neutrik® or equivalent are recommended for the unbalanced to balanced AES conversion:
NADITBNC-F: Female chassis XLR 110 Ω input - female BNC 75 Ω output. http://www.neutrik.com/fl/en/audio/210_309314683/NADITBNC-F_detail.aspx
NADITBNC-M: Female BNC 75 Ω input - male chassis XLR 110 Ω output. http://www.neutrik.com/fl/en/audio/210_2044239418/NADITBNC-M_detail.aspx
NADITBNC-FX: Female cable end XLR 110 Ω input - female BNC 75 Ω output. http://www.neutrik.com/fl/en/audio/210_1576769505/NADITBNC-FX_detail.aspx
NADITBNC-MX: Female BNC 75 Ω input - male cable end XLR 110 Ω output. http://www.neutrik.com/fl/en/audio/210_1923043515/NADITBNC-MX_detail.aspx
HMX6803
+
and OP
+
HMX
+
Installation and Operation Manual
13
Setting Jumpers
HMX6803
+
and OP
+
HMX
+
modules have one jumper, CJ1, which sets the module for local
or remote control. See Setting Jumper CJ1 for Local or Remote Control on page 13.
The submodule on HMX6803
+
AI
+
T, OP
+
HMX
+
AI
+
13T, and OP
+
HMX
+
AI
+
CxxT modules has eight impedance jumpers that can be set for High-Z or 660 Ω
Ω
/Hi-Z Input Impedance Control on page 13.
Setting Jumper CJ1 for Local or Remote Control
The HMX6803
+
and OP
+
HMX
+
module has one jumper, CJ1, which sets the module for local or remote control.
Note: You need to configure modules for local or remote operation prior to power-up. To change the configuration, first remove power from the module, reset the jumper, and then reapply power.
CJ1 jumper
Figure 2-1 Jumper Location
1 Locate jumper CJ1 on the module (behind the mode select rotary switch).
shows the location of the CJ1 jumper.
2 Place a jumper on pins 1 and 2 to set the module for Remote control, or pins 2 and 3 to set the module for Local
3 2 1 3 2 1
Remote control setting
Local control setting
Figure 2-2 CJ1 Settings for Local and Remote Control
Note: The white triangle near the jumper pins on the module indicates pin 1.
Setting Jumpers for 600
Ω
/Hi-Z Input Impedance Control
This procedure only applies to the HMX6803
+
AI
+
T, OP
+
HMX
+
AI
+
13T, and
OP
+
HMX
+
AI
+
CxxT analog audio submodule.
14 Chapter 2
Installation
Follow this procedure to select an analog impedance of 600
Ω or Hi-Z on each channel:
1 Locate jumpers CH1A, CH1B, CH2A, CH2B, CH3A, CH3B, CH4A, and CH4B on the analog audio module.
Figure 2-3 shows the location of these jumpers.
Impedance jumpers
CH1A-CH 4B
Figure 2-3 Impedance Jumpers on Analog Audio Submodule
2 Place a jumper on pins 1 and 2 to set the module for 600
Ω input, or pins 2 and 3 to set the module for Hi-Z analog impedance input, as in
.
Do this for all eight channel jumpers.
Channel 1B set for 600 Ω input
3 2 1
Channel 2A set for Hi-Z input
3 2 1
Figure 2-4 Jumper Settings for 600W or Hi-Z Inputs
Maximum 6800
+
Frame Power Ratings
See the FR6802
+
Frame Installation and Operation Manual for information about installing and operating an FR6822
+
, FR6802
+
QXF or FR6802
+
frame and its components.
CAUTION: Before installing this product, read the 6800
+
Series Safety Instructions
and Standards Manual shipped with every 6800
+
Frame Installation and Operation
Manual or downloadable from our website. This safety manual contains important information about the safe installation and operation of 6800
+
series products.
The power consumption for the HMX6803
+
and OP
+
HMX
+
describes the maximum allowable power ratings for 6800
+
frames. Note the given maximums before installing any 6800
+
modules in your frame.
HMX6803
+
and OP
+
HMX
+
Installation and Operation Manual
15
HMX6803
+
and OP
+
HMX
+
modules operate only in fan-cooled FR6802
+
and FR6822
+ frames, subject to the limitations shown in
. These modules cannot be installed in
6800/7000 series frames.
Note: To maintain proper temperatures, ensure that the front panel is closed at all times and that the fan module is fully operational.
Table 2-3 Maximum Power Ratings for 6800
+
Frames
6800
+
Frame Type
Max. Frame
Power
Dissipation
FR6802
+
XF
(frame with AC power supply)
FR6802
+
XF48
(frame with DC power supply)
120 W
105 W
FR6802
+
QXF frame
(with AC or DC power supply)
120W
FR6822
+
frame (with AC or DC power supply) 120W
Number of
Usable
Slots
20
20
20
20
Max. Power
Dissipation
Per Slot
6 W
5.25 W
6 W
6 W
Installing 6800
+
Modules
Required Frames and Back Connector Types
HMX6803
+
and OP
+
HMX
+
modules have double-width back connectors that can be installed in an FR6802
+
XF, FR6822
+
, or FR6802
+
QXF frame. HMX6803
+
and OP
+
HMX
+ modules cannot be installed in an FR6802
+
DM frame, a FR6800/7000 frame, or a frame without fans.
See your 6800
+
Frame Installation and Operation Manual for details on installing back connectors in an FR6802
+
or FR6822
+ frame.
A FR6802
+
RM (Rear Support Extension Rails for 6800
+
series frames) option is recommended for the HMX6803
+
and OP
+
HMX
+
modules. See your 6800
+
Frame
Installation and Operation Manual for installation instructions.
Installing and Removing HMX6803
+
Modules
These modules require no specialized installation or removal procedures. However, if installing both front and rear modules, ensure that the back module is installed first before plugging in the front module.
When removing both the front and rear modules, ensure that the front module is unplugged from the frame first, before removing the rear module.
See the 6800
+
Frame Installation and Operation Manual for information about installing and operating a frame and its components.
16 Chapter 2
Installation
See the 6800
+
Safety Instructions and Standards Manual for important information about safely installing your module.
Once you have installed your HMX6803
+
and OP
+
HMX
+
modules, you can connect them to the appropriate input and outputs.
Installing
OP
+
HMX
+
Modules
Front and back modules in the OPTO
+
series have plastic caps that protect the fragile laser connections from damage. You must remove these protective covers before you install the
back and front modules (see Figure 2-5
).
In addition, all fiber optic connections must be inspected and cleaned before they are assembled. Carefully follow the inspection and cleaning steps described in the next pages.
Additional safety information appears in
Laser Safety Guidelines on page 77.
CAUTION: Ensure that you remove the fiber optic protective covers from the front and back modules before installation. Take care to avoid touching the fiber optic connections. Thoroughly clean the connections before installation. Remove power from the frame before installing or removing back modules.
Remove this protective cover
Remove these protective covers
Figure 2-5 Protective Covers for Laser Connectors
Back Module Installation
Follow these steps to install the back module into an FR6802
+
XF, FR6802
+
XF48, FR6822
+
, or FR6802
+
QXF frame:
1 Remove a blank back plate from the frame.
Do not discard the blank back plates. They may be needed for future configurations.
HMX6803
+
and OP
+
HMX
+
Installation and Operation Manual
17
2 On the side of the back module that inserts into the front module, remove the inner protective cap from the fiber connection (see
CAUTION: Microscopic dust or other contaminants can seriously impair or disable a fiber optic network. Observe strict cleaning procedures. Do not touch the end of the fiber.
3
Follow the inspection and cleaning procedure that begins on page 18.
4 If it is already installed, remove the front module from the slot.
5 Install the new back module by inserting the bottom lip into the required frame slot, and then screwing it into place.
Ensure that the EMI gaskets on the right side of the back module remains in place during the installation. The EMI gaskets fit tightly.
6 Apply the adhesive label to the back module if it is supplied separately.
Front Module Installation
Follow these steps to install the front module:
1 Pull out the finger-release screws on the right and left side of the front panel of the frame, and then open it.
2 Locate the front module slot that corresponds with the matching back module.
3 Gently remove the outer and inner protective caps from the laser connections. (see
CAUTION: Microscopic dust or other contaminants can seriously impair or disable a fiber optic network. Observe strict cleaning procedures. Do not touch the end of the fiber.
4
Follow the fiber cleaning instructions that begin on page 18.
5 Ensure that your front module matches with a corresponding back module of the same name.
6 Slide the module into the guides in the frame.
7 When the module edge is flush with the guide, close the extractor handle.
The module is properly seated when its edge is flush with the guide edge and the extractor handle closes.
8 Close the front panel to ensure proper frame ventilation.
To prevent overheating, keep the front panel closed and all back module plate slots covered during operation.
Removing OP
+
HMX
+
Modules
Note: The removal steps provided here are similar to those outlined in your 6800
+
Frame
Installation and Operation Manual. Refer to that manual for detailed information about installing and operating a frame and its components.
Front Module
Follow these steps to remove a front module from a frame:
18 Chapter 2
Installation
1 Pull out the finger-release screws on the right and left side of the front panel of the frame, and then open the front panel.
2 Grasp the extractor handle on the installed module, and then pull the module out of its slot.
Use the handle as a lever.
3 Close the front panel to ensure proper frame ventilation.
Back Module
Follow these steps to remove a back module from a frame:
1 Remove the front module, as described above.
2 Unscrew the top of the corresponding back module, and then tip it towards you.
3 Pull the bottom lip of the back module from its slot.
4 Reinstall a new or blank back plate in the empty slot to ensure proper frame ventilation.
5 Reinstall the front module.
Inspecting and Cleaning Fiber Optic Connections
Small amounts of microscopic dust or other contaminants can seriously impair or disable a fiber optic network. To ensure that your network operates reliably, you must carefully inspect and clean each connection when installing OPTO
+
products.
lists some typical contaminants of a fiber optic connection. The inspection and
cleaning procedure begins on page 19.
Table 2-4 Typical Contaminants
Contaminant Comments
Dust particle, 1 micron Can block up to 1% of the light transmission, creating a loss of 0.05 dB
Dust particle, 9 microns
Human hair
Oil
Film residues
Powdery coatings
Although microscopic, the particle can completely block the fiber core
Typically 50 to 75 microns in diameter
Frequently caused by touching
Can accumulate from vapors or smoke
Can be left behind after water or other solvents evaporate
Important Points
Before you begin cleaning, always inspect the fiber connections.
Inspect and clean both fiber ends every time you make a connection.
Keep a protective cap on unplugged fiber connectors.
Do not touch the end of a fiber.
Store unused protective caps in a clean resealable container, located nearby for easy access.
Do not reuse cleaning tissues or swabs.
Do not allow alcohol or another wet cleaning agent to dry on a fiber end.
Never touch the dispenser tip of an alcohol bottle or any clean portion of a tissue or swab.
Scratches and dust
HMX6803
+
and OP
+
HMX
+
Installation and Operation Manual
19
Use care when handling the fiber; do not twist or pull.
Keep your cleaning fluids away from open flame or spark.
describes the acceptable limits of defects in a fiber connection.
Zone 1
(0 to 20 micron diameter)
No scratches or digs are allowed
Zone 2
(20 to 50 micron diameter)
Maximum of 3 scratches <1.0 micron width is acceptable;
Maximum 1.0 micron light dig is acceptable
Zone 3
(50 to 126 micron diameter)
Maximum 25 micron dig is acceptable;
Maximum scratch size of 1.0 micron is acceptable
Maximum 25 micron diameter dig is acceptable
Figure 2-6 Fiber Optic Cross Section
Inspection and Cleaning Procedure
Inspection
WARNING: Eye damage may occur if an optical instrument such as a microscope, magnifying glass, or eye loupe is used to stare at an energized fiber end.
To inspect and clean the fibers, follow these steps:
1 Ensure the fiber is not “live.”
2 Inspect the fiber endface with a fiberscope.
3
If the fiber endface is clean, return to the installation instructions on page 16 for back
modules or page 17 for front modules.
If the connector is dirty, proceed to the dry cleaning instructions below.
Dry Cleaning
If you are using cartridge or pocket-style dry cleaning tools, follow the manufacturer’s directions. If you are using lint-free wipes, follow these steps:
1 Fold the lint-free wipe four to eight times into a square, taking care to avoid touching the cleaning surface of the wipe.
20 Chapter 2
Installation
2 Lightly wipe the fiber tip in the central portion of the lint-free wipe.
CAUTION: Do not scrub the fiber. Excessive rubbing will leave scratches.
3 Repeat the wiping action on another clean section of the wipe or a new wipe.
4 Inspect the connector again with the fiberscope.
5
If the connection is clean, return to the installation steps on page 16 for back modules, or
If the connector is still dirty, proceed to the wet cleaning instructions.
Wet Cleaning
Using 99% isopropyl alcohol and lint-free wipes, follow these steps to wet clean the fiber:
1 Fold the wipe into a square, about four to eight layers thick.
2 Moisten one section of the lint-free wipe with one drop of 99% alcohol, ensuring that a portion of the wipe remains dry.
3 Lightly wipe the fiber end in the alcohol-moistened portion of the lint-free wipe.
4 Immediately repeat the wiping action on the dry section of the wipe, removing any residual alcohol.
5 Inspect the fiber endface again, and if necessary, repeat the wet cleaning with another clean section of the lint-free wipe.
CAUTION: Do not scrub the fiber. Excessive rubbing will leave scratches.
6 Dry clean any remaining residue, and then inspect the connector again.
7 If the contamination persists, repeat the dry and wet cleaning procedure until the endface is clean.
If the fiber end still remains dirty after repeated cleaning attempts, call Customer Service for further instructions.
If the fiber end is clean, return to the installation instructions on page 16 for back modules,
Upgrading
Module
Firmware
This module’s firmware can be updated using CCS Pilot, CoPilot, or Navigator version 3.1.1 or higher, or the HTTP software upgrade tool. In order to perform these upgrades, your frame must be equipped with a 6800
+
ETH module. See your frame manual for more information.
3
Operation
Operating
Notes
When you set the control parameters on the HMX6803
+
and OP
+
HMX
+
, observe the following:
If you make changes to certain parameters, other related parameters may also be affected. See
Cross-Functional Parameter Changes on page 32 for more
information.
When you change a parameter, the effect is immediate. However, the module requires up to 30 seconds to save the latest change. After 30 seconds, the new settings are saved and will be restored if the module loses power and must be restarted.
Q-SEE Compliant Thumbnails
When installed in an FR6802
+
QXF or FR6822
+
frame that also contains a 6800
+
ETH resource module, HMX6803
+
and OP
+
HMX
+
module control windows have an extra
Streaming tab in CCS Pilot and Navigator (version 3.2.1 or later). There you can view output video from the module.
In addition, video from the HMX6803
+
and OP
+
HMX
+
, displayed at up to three frames per second, can be displayed on the 6800
+
ETH’s control page, and (for CCS Navigator only) on
Graphical Navigation pages.
Note: HMX6803
+
and OP
+
HMX
+
modules all show a HMX6803
+
label in Navigator.
Thumbnail streaming is not supported for the following video standards:
1080i 60
720p 60
1080p 24/25/29.97/30
1080psF 23.98/24
1080p 50/59.94/60
Activating HMX6803
+
and OP
+
HMX
+
Functions
The following sections provide information about the HMX6803
+
and OP
+
HMX
+
special functions:
21
22 Chapter 3
Operation
Adding a License Key on page 22
Audio Embedding Modes on page 23
Audio Embedding Errors on page 27
Seamless Sound Function on page 29
Test Pattern Generator on page 30
Dolby-E Automatic Header Alignment on page 31
Maintaining Audio/Video Alignment on page 32
Adding a License Key
Note: For assistance with a license key, or to purchase a license key, please contact your
Sales representative.
To enter a license key to activate AES audio and/or 3G HD video, your CCS software must be in Control mode.
1 Select the HMX6803
+
module in the Navigation pane, right click, and then select Control to open the module’s Control window.
2 Select the Parameters tab.
3 Select General in the tree view, and then type your license key in the License Key field.
Note: HMX6803
+
and OP
+
HMX
+
modules appear as HMX6803
+
modules in Navigator.
If your license key is valid, the Installed Options field displays the features that are activated on the module, which in this case is 3G and/or AES .
Audio Test
Tones
describes the frequency and levels of each audio output test tone, available as a selection from each of the Output Ch ( 1–16 ) Source Select and Audio Procamp AES
(1A-8B) Out Source
Table 3-1 Audio Test Tones
Test Tone
Test Tone 1
Test Tone 2
Test Tone 3
Test Tone 4
EBU R68
SMPTE RP155
Frequency
400 Hz
1 kHz
2 kHz
4 kHz
1 kHz
1 kHz
Level
-18 dBFS
-18 dBFS
-18 dBFS
-18 dBFS
-18.06 dBFS
-20 dBFS
HMX6803
+
and OP
+
HMX
+
Installation and Operation Manual
23
Audio
Embedding
Modes
The audio embedder component in the HMX6803
+
and OP
+
HMX
+
is composed of several smaller subcomponent blocks:
One ancillary data stripper (ADS)
Four audio embedding subcomponents
The first subcomponent is an ancillary data stripper (ADS). This block removes all ancillary data packets in the input SDI stream, prior to embedding.
Following the ADS block are four separate audio-embedding subcomponents. Each subcomponent has the ability to operate on only one audio group, either appending or overwriting a predetermined group onto the SDI stream.
The audio embedding modes are Audio Group ( 1–4 ) Embedding Mode parameters (see
briefly describes the Append , OverWrt , and Auto options available from each of the embedding modes.
Table 3-2 Embedding Mode Options
Options
Append
OverWrt
Auto
Description
Attempts to insert the audio data and control packets immediately following the last existing audio data/control
packet in the horizontal ancillary region (see Append
Attempts to overwrite existing audio data and control packets of the same group number with the new audio data (see
Overwrite Embedding on page 25)
Attempts first to overwrite existing audio data and control packets of the same audio group number; failing that, it appends the new audio data and control packets immediately following the last existing audio data/control packet (refer to the Audio Group (1–4) Exists
determine what audio groups are already present in the incoming SDI signal)
Append Embedding
When you select Append embedding, the HMX6803
+
and OP
+
HMX
+
attempts to insert the audio data and control packets immediately following the last existing data/control packet in the horizontal ancillary data space (ADS). Append embedding is only valid if the audio group to be embedded does not already exist.
shows how append embedding will appear in the ancillary data space when there is no previous audio or other data.
ADS before embedding
EAV
ADS after embedding group 1
EAV Group 1
Figure 3-1 In Append Embedding Mode, Adding Group 1 When No Other Data is Present
24 Chapter 3
Operation
When auxiliary data exists in the ancillary data space, appended audio appears following that data, as shown in
.
ADS before embedding
EAV
Other auxilliary data
A
Other auxilliary data
B
ADS after embedding group 1
EAV
Other auxilliary data
A
Other auxilliary data
B
Group 1
Figure 3-2 In Append Embedding Mode, Adding Group 1 When Auxiliary Data is Present
If you attempt to insert audio into Group 1 when Group 1 audio data already exists in the
ancillary data space, an error will be returned, as shown in Figure 3-3 .
ADS before embedding
EAV
Pre-existing
Group 1
ADS after attempting to embed group 1
EAV
Pre-existing
Group 1
Result: Error is returned
Figure 3-3 Append Embedding Mode When Adding Group 1 and a Group 1 Already Exists
If you insert Group 2 audio when there is pre-existing Group 1 audio in the ancillary data space and no Group 2 audio, the Group 2 audio will be inserted following the Group 1
audio, as shown in Figure 3-4 .
ADS before embedding
EAV Group 1
ADS after embedding group 2
EAV Group 1 Group 2
Figure 3-4 Append Embedding Mode, Adding Group 2 Following Group 1
HMX6803
+
and OP
+
HMX
+
Installation and Operation Manual
25
If you insert Group 1 audio when there is pre-existing Group 2 audio in the ancillary data space and no Group 1 audio, the Group 1 audio will be inserted following the Group 2 audio, as shown in
.
ADS before embedding
EAV Group 2
ADS after embedding group 1
EAV Group 2 Group 1
Figure 3-5 Append Embedding Mode, Adding Group 2 Following Group 1
An audio group cannot be divided. In Append embedding, the audio group is always added following the last block in the ADS. If there is not enough room to append the audio group following the last block of auxiliary data or audio in the ADS, the attempt will result in an error, as shown in
ADS before embedding
EAV
Other auxillary data
Other auxillary data
Other auxillary data
ADS after attempting to embed group 1
EAV
Other auxillary data
Result: Error is returned
Other auxillary data
Other auxillary data
Figure 3-6 Append Embedding Mode Returns Error When Auxiliary Data Exists in all Audio Groups
Overwrite Embedding
When you select Overwrite embedding, the module attempts to overwrite any existing audio data and control packets of the same group number with the new audio data. This setting is valid only if the audio group to be embedded already exists. If the new sample distribution does not exactly match the existing audio data packet sample distribution, the embedder will mark some audio data packets for deletion (DID word will be set to 180h).
Note: To avoid sample distribution issues, activate the ADS Clean feature (see
26 Chapter 3
Operation
When you attempt Overwrite embedding and there is no previous audio (as in Figure 3-7 ),
it will return an error because there is nothing to overwrite.
ADS before embedding
EAV
ADS after attempting to embed group 1
EAV
Result: Error is returned
Figure 3-7 Overwrite Embedding Mode When There is No Pre-Existing Audio
Figure 3-8 shows how overwrite embedding will appear in the ancillary data space when
there is auxiliary data where Group 1 should be inserted.
ADS before embedding
EAV other auxilliary data
A other auxilliary data
B
ADS after attempting to embed group 1
EAV other auxilliary data
A other auxilliary data
B
Result: Error is returned
Figure 3-8 Overwrite Embedding Mode When There is Auxiliary Data on Group 1
Figure 3-9 shows how overwrite embedding will appear in the ancillary data space when
there is pre-existing Group 1 audio. This operation is successful.
ADS before embedding
EAV Pre-existing Group 1
ADS after embedding group 1 (with overwrite group specified as Group 1)
EAV
Group 1
Figure 3-9 Overwrite Embedding Mode When There is Group 1 Audio in the Group 1 Space
HMX6803
+
and OP
+
HMX
+
Installation and Operation Manual
27
Audio
Embedding
Errors
Group ( 1–4 ) Append Embedding Error and Group ( 1–4 ) Overwrite
Embed Error
audio embedding errors (also see page 48).
Table 3-3 Audio Embedding Error Descriptions
Error
Group (1–4)
Append
Embedding
Error
Description
This error occurs if the embedder is set to Append mode for a particular audio group, but that audio group already exists in the incoming SDI signal.
Group (1–4)
Overwrite
Embed Error
In this case, the embedder does not embed another audio data and control packet of the same audio group, as this will result in incorrect audio sample distribution.
This error occurs if the embedder is set to Overwrite mode for a particular audio group, but that audio group does not exist in the incoming SDI signal
To avoid embedding errors, follow these guidelines:
Set the embedding mode to Auto . If the group is present, it will be overwritten; if it is not present, it will be appended. The overwrite and append errors are actually warnings that the operation is not being performed.
In SD-SDI mode do not overwrite embedded groups of 20-bit audio samples with groups of 24-bit audio samples. The required extended data packet information appended to that group may overwrite a pre-existing audio group. For 24-bit audio embedding, use the ADS Clean feature provided.
Mono Channel Audio Embedding
To embed audio on a channel-by-channel (mono) basis, preserving some embedded audio channels while replacing others from external AES sources, follow these steps:
1 Configure the input audio routing path (Input > Audio > Routing) by selecting audio pair sources to the individual audio sample rate converters.
By default, SRCs 1-8 are assigned to the 8 deembedded audio sources (DMX Grp1 Ch1/2,
DMX Grp1 Ch3/4, DMX Grp2 Ch1/2, etc.) and SRCs 9-16 are assigned to the external AES audio sources ( AES1a/1b, AES2a/2b , etc.).
2 Configure the output audio routing path (Output > Audio Source Select > Embedded
Audio) by selecting sources to each mono embedded audio output channel.
Each SRC ( SRC1a, SRC1b, SRC2a, etc.) can be selected to any output embedded audio channel, allowing for any input-to-output audio configuration.
3 Remove or preserve existing embedded audio with the ADS Clean parameter (Processing >
Audio).
4 Use the Audio Group (1-4) Embedding Mode parameters (Processing > Audio >
Embedding) to select the desired audio group embedding mode for each audio group.
In Auto mode, non-existing audio groups are appended and existing audio groups are overwritten.
In Overwrite mode, the original audio is preserved using the settings in step 2.
In Off mode, audio groups are untouched unless the ADS Clean parameter is enabled.
28 Chapter 3
Operation
Example: Replacing Audio Channel 1 in Group 1 Only
To replace only embedded audio channel 1 in group 1 with audio from external AES 1A source, follow these steps:
1 Leave the input audio routing path at the default configuration (SRCs 1-8 from deembedded audio, SRCs 9-16 from external AES audio).
2 Route the output audio sources as follows (Output > Audio Source Select > Embedded
Audio):
Output Emb Ch 1 Source Select: SRC9a
Output Emb Ch 2 Source Select: SRC1b
Output Emb Ch 3 Source Select: SRC2a
Output Emb Ch 4 Source Select: SRC2b
3 Preserve existing embedded audio by setting the ADS Clean parameter (Processing >
Audio) to No .
4 Set the audio group embedding mode (Processing > Audio > Embedding):
Audio Group 1 Embedding Mode : Auto
Audio Group 2 Embedding Mode : Off
(incoming audio group 2 will be preserved)
Audio Group 3 Embedding Mode : Off
(incoming audio group 3 will be preserved)
Audio Group 4 Embedding Mode : Off
(incoming audio group 4 will be preserved)
Audio V-Fade
To enable a smooth deembedded audio V-fade transition when switching video sources, make the following settings:
Set the Audio V-Fade parameter to Enable .
Set the Audio LOV Output Mode parameter to Mute .
Set the ADS Clean parameter to Yes .
Note: AES outputs in this mode are not AES11 alignment compliant and are not aligned with video.
For proper operation in this mode, set the user delay parameters for all audio channels
(Processing > Audio > Delay) to the same value.
Input Audio
Rate
When embedding audio in PCM mode ( Audio Ch [ 1–16 ] Format = PCM or Audio Ch [ 1–
16 ] Format = Auto and Audio Ch [ 1–16 ] Format Feedback = PCM ), the input audio sample rate may be from 32 kHz to 108 kHz. This input audio will be sample rate converted to 48 kHz prior to embedding in the video signal; as well, the embedder will indicate 48 kHz in the “Rate” word of the audio control packet for each embedded audio group.
When embedding audio in Non-PCM mode ( Audio Ch [ 1–16 ] Format = Non-PCM or
Audio Ch [ 1–16 ] Format = Auto and Audio Ch [ 1–16 ] Format Feedback = Non-PCM ), the input audio sample rate must be 48 kHz, and it must be frequency locked to the source video. In this scenario, the sample rate conversion function is bypassed and the embedder will indicate 48 kHz in the “Rate” word of the audio control packet for each embedded audio group.
(The parameters are listed on page 39.)
HMX6803
+
and OP
+
HMX
+
Installation and Operation Manual
29
Audio Path
The output audio source selection consists of two sets of controls.
Input Sample Rate Conversion (SRC) routing source selections
Each SRC source can be assigned to one of the following sources:
AES In (1A/1B to 8A/8B) (with AES8 option)
Demuxed audio (Group 1 channels 1/2 to Group 4 channels 3/4)
Output Audio Source Selection for the embedded audio
Each output embedded Audio channel can be assigned to one of the following sources:
SRC (1a to 16b)
In Pair (SRC1a+1b to SRC16a+16b) Sum
TstTone 400 Hz
TstTone 1 kHz
TstTone 2 kHz
TstTone 4 kHz
EBU R68
SMPTE RP155
SRC1a+2a
SRC1b+2b
SRC2b+3b
SRC2a+4a
SRC2b+4b
(The parameters are listed on page 39.)
Seamless
Sound
Function
When used in conjunction with HDX6803
+
or SFS6803
+
in a de-embedding mode, the
HMX6803
+
can provide an uninterrupted (“popless”) embedding and de-embedding path for the discrete audio channels regardless of the presence or input switching of the video, as long as a constant video standard is maintained.
HMX6803
+
/OP
+
HMX
+
connected to HDX6803
+
/OP
+
HDX
+
HMX6803
+
/OP
+
HMX
+
parameter settings (embedding module):
Set the Seamless Sound Enable parameter (Processing > Audio) to Enable .
Set the Audio LOV Output Mode to Pass .
If an audio group already exists and you want to replace it, set the ADS Clean parameter to
Yes (Processing > Audio > Embedding).
Note: The ADS Clean parameter removes all audio groups from the video stream.
If the audio group already exists and you do not want to replace it, or if the audio group to be embedded does not exist, set the ADS Clean parameter to No (Processing > Audio >
Embedding).
To set an audio group to be embedded to the Append mode, set the Audio Group 1-4
Embedding Mode parameter to Append (Processing > Audio > Embedding).
For optional minimum propagation delay, set the Video Delay Bypass parameter to Yes
(Processing > Video > Delay).
30 Chapter 3
Operation
HDX6803
+
/OP
+
HDX
+
parameter settings (de-embedding module):
Set the Seamless Sound Enable parameter (Processing > Audio) to Enable .
Set the Audio LOV Output Mode to Pass .
To set the AES output(s) to be sourced directly from the audio deembedder by using the appropriate Demux Ch source, set the Output AES 1-8 Source Select parameter to
Demux Ch 1/2 , Demux Ch 3/4 , etc. (Output > Audio Source Select > AES Audio).
For optional minimum propagation delay, set the Video Delay Bypass parameter to Yes
(Processing > Video > Delay).
HMX6803
+
/OP
+
HMX
+
connected to SFS6803
+
/OP
+
SFS
+
HMX6803
+
/OP
+
HMX
+
parameter settings (embedding module):
Set the Seamless Sound Enable parameter (Processing > Audio) to Enable .
Set the Audio LOV Output Mode to Pass .
If an audio group already exists and you want to replace it, set the ADS Clean parameter to
Yes (Processing > Audio > Embedding).
Note: The ADS Clean parameter removes all audio groups from the video stream.
If an audio group already exists and you do not want to replace it, or if the audio group to be embedded does not exist, set the ADS Clean parameter to No (Processing > Audio >
Embedding).
To embed an audio group in Append mode, set the Audio Group 1-4 Embedding Mode parameter to Append (Processing > Audio > Embedding).
For optional minimum propagation delay, set the Video Delay Bypass parameter to Yes
(Processing > Video > Delay).
SFS6803
+
/OP
+
SFS
+
parameter settings (de-embedding module):
Set the Seamless Sound Enable parameter (Processing > Audio) to Enable .
Set the Audio LOV Output Mode to Pass .
To set the AES output(s) to be sourced directly from the audio deembedder using the appropriate Demux Ch source, set the Output AES 1-8 Source Select parameter (s) to
Demux Ch 1/2 , Demux Ch 3/4 , etc. (Output > Audio Source Select > AES Audio).
For optional minimum propagation delay, set the Frame Sync Bypass parameter to Yes
(Processing > Video > Synchronization).
Test Pattern
Generator
When the Test Pattern Enable
parameter (listed on page 51) is set to
On , the video output displays one of the following options:
75% color bars
Pathological
100% color Bars
HMX6803
+
and OP
+
HMX
+
Installation and Operation Manual
31
EQ Pathological
PLL Pathological
Dolby-E Automatic Header Alignment
When you embed Dolby E audio, the module automatically adjusts input audio delay such that the Dolby E header resides on the line specified by the Dolby E Start Line parameter, with a tolerance of ±1 line.
shows the ranges and default values for the Dolby E
Start Line parameter.
Table 3-4 Dolby E Automatic Header Alignment by Video Standard
Video Standard
525
625
1080i/p/psF
720p
Range
13–25
9–30
15–54
20–71
Default
15
11
19
25
Audio Delay
Ranges
Depending on the amount of delay applied to the video stream, the available range for the
audio delay parameters varies. The ranges are listed in Table 3-5 .
Table 3-5 Audio Delay Range Depending on the Amount of Video Delay
Condition
Video Delay greater than 31 frames
Video Delay less than 32 frames
Parameters
Input Audio Ch 1–16 Delay
Input Audio AES 1A–4B Delay
Input Audio Ch 1–16 Delay
Input Audio AES 1A–4B Delay
Range
0 to 660.00 ms
0 to 1320.00 ms
For Dolby-E automatic header alignment to operate correctly, the input SDI must be frequency locked to the same reference source as the Dolby-E source.
External Audio Processing Delay
Set the External Audio Delay parameter to the amount of processing delay that is incurred by external audio before it enters the HMX6803
+
. While external audio delay is not tracked by the audio synchronizer, an equivalent amount of video delay is applied to the video path to realign the output video with the externally applied audio.
The Actual Video Delay Used parameter monitors the amount of additional video delay applied. This parameter is a sum of this compensating video delay plus any video delay applied using the Video Delay parameter, measured in frames.
Set the associated SRC (1-16) Ext Audio Align parameter to On . (To determine which SRC is the source of the externally processed audio, check the parameter settings within the
Input > Audio > Routing menu.) This ensures the externally processed audio is realigned with output video once it is output from the module (embedded or AES output).
32 Chapter 3
Operation
Maintaining
Audio/Video
Alignment
When you use Sample Rate Conversion with PCM Audio to change audio rates and provide audio synchronization with output video, this introduces a delay in the audio signal path.
To maintain an alignment between video and audio in PCM mode, set the Audio/Video
Align parameter (Processing > Video > Delay) to Yes . This introduces a matching video delay and maintains audio/video alignment.
When using Non-PCM Audio, or when sample rate converters are bypassed, set the Audio/
Video Align parameter (Processing > Video > Delay) to No to avoid excessive video delay.
AFD/WSS/VI Detection and Insertion
AFD, WSS (625 only), and VI (526/625 only) embedded video metadata specify the active area to be displayed from a video input. These codes do not do any aspect ratio conversion themselves, but indicate how the video should appear to systems capable of interpreting the data.
Seven input parameters (Input > AFD/VI/WSS De-embedder) on HMX6803
+
modules indicate the presence of AFD, WSS, and VI data when you determine the lines where this data is likely to appear, if present.
The single processing parameter ( Out Aspect Ratio , which appears at Processing >
Video > AFD/VI/WSS) determines the options for the AFD Select and VI Select parameters.
Twelve output parameters (Output > AFD/VI/WSS Embedder) determine the line to embed AFD, WWS, and/or VI codes on, the code(s) to be embedded, and what happens when a code disappears from the input.
Cross-Functional Parameter Changes
When you configure certain parameters, you force a change in other associated parameters. The various conditions that affect parameter availability or settings are described in the following sections:
ADS Clean Parameter on page 33
PCM/Non-PCM Settings on page 33
Channel Word Length on page 34
Parameter Availability Based on Operating Mode on page 34
Out Aspect
Ratio
When the Out Aspect Ratio parameter (Processing > Video > AFD/VI/WSS) is set to 4:3, the AFD Select and VI Select parameters (Output > AFD/VI/WSS Embedder) have the following options:
16:9 top
14:9 top
>16:9 in 4:3
4:3 full
16:9 l
14:9 l
HMX6803
+
and OP
+
HMX
+
Installation and Operation Manual
33
4:3 a 14:9
16:9 l a 14:9
16:9 l a 4:3
When the Out Aspect Ratio parameter (Processing > Video > AFD/VI/WSS) is set to 16:9, the AFD Select and VI Select parameters (Output > AFD/VI/WSS Embedder) have the following options:
16:9 full
14:9 p
>16:9 in 16:9
4:3 p
16:9 prtctd
4:3 p a 14:9
16:9 a 14:9
16:9 a 4:3
ADS Clean
Parameter
Depending on the setting of the ADS Clean
parameter (listed on page 44), the
Audio
Group ( 1–4 ) Embedding Mode parameters will have different options.
Table 3-6 ADS Clean Parameter
ADS Clean
State
Yes
No
Audio Group (1–4)
Embedding Mode Options
Off
Append
Off
Append
OverWrt
Auto
PCM/
Non-PCM
Settings
If a channel’s format is PCM, that channel’s Gain and Invert parameters are activated. (The
parameters are listed on page 47.)
Table 3-7 describes how the PCM format setting for Output Embedded Ch 1 affects the
Gain and Invert options for embedded channel 1. Similar conditions apply to channels 2-16 and AES Outputs 1A–8B when their audio formats are changed.
34 Chapter 3
Operation
Note: The forced setting (center column) takes effect before the identified parameter (right column) becomes activated or deactivated.
Table 3-7 Cross-Functional Parameters
Condition Forced Setting
Audio Ch 1 Format = Non-PCM or
Audio Ch 1 Format = Auto and
Audio Ch 1 Format Feedback = Non-PCM
Audio Ch 1 Format = PCM or
Audio Ch 1 Format = Auto and
Audio Ch 1 Format Feedback= PCM
Audio Ch 1 Gain = 0 dB
Audio Ch 1 Invert = No
Enabled/Disabled
Parameters
Audio Ch 1 Gain = Disabled
Audio Ch 1 Invert = Disabled
Audio Ch 1 Gain = Enabled
Audio Ch 1 Invert = Enabled
Channel
Word Length
When the incoming video is 3G or 1.5G HD-SDI (and you have the optional license key for those video input and outputs), the default value for all Audio Ch XX-XX Word Length parameters is 24 bits.
When the incoming video is SD-SDI, the default value is 20 bits. However, if at least one channel is set to 24 bits, the corresponding embedder will enable 24 bits embedding.
The Audio Channel Word Length
parameters are listed on page 53.
Parameter Availability Based on Operating Mode
Some parameters may or may not be available depending on whether the module is in HD or SD mode.
The HD parameters apply when the SDI Video Standard Set parameter is set to one of the HD operating modes, or when it is set to Auto and SDI IP Video Standard
Feedback is one of the HD operating modes.
HMX6803
+
and OP
+
HMX
+
Installation and Operation Manual
35
The SD parameters apply when SDI Video Standard Set is set to either 525i 59.94 or
625i 50, or when it set to Auto and SDI IP Video Standard Feedback is 525i 59.94 or
625i 50.
Table 3-8 Parameter Availability Based on Operating Mode
Condition
1080i/p/psf and
720p 3G or 1.5G
HD Operating
Mode
Available Parameters
Y CRC/Link B Error Counter
C CRC/Link B Error Counter
Y CRC/Link A Error Counter
C CRC/Link A Error Counter
CRC Error Counter Clear
SDI 525i 59.94
Operating Mode
SDI 625i 50
Operating Mode
EDH Present
EDH Error
Counter
EDH Error
Counter Clear
VI Detect Line
Fld1
VI Detect Line
Fld2
VI AFD Present
VI Scan Present
EDH Present
EDH Error
Counter
EDH Error
Counter Clear
VI Detect Line
Fld1
VI Detect Line
Fld2
VI AFD Present
VI Scan Present
Out Aspect Ratio
VI Control
VI Embed Line
Out Aspect Ratio
VI Control
VI Embed Line
VI Select
SD Out VI with AFD
VI Output (AFD)
VI Output (Scan)
VI Select
SD Out VI with AFD
VI Output (AFD)
VI Output (Scan)
WSS Detect Line
WSS Present
WSS Control
WSS Embed Line
WSS Select
WSS Output
Unavailable Parameters
EDH Present VI Select
EDH Error Counter SD Out VI with AFD
EDH Error Counter
Clear
VI Detect Line Fld1
VI Detect Line Fld2
VI AFD Present
VI Scan Present
Out Aspect Ratio
VI Control
VI Embed Line
Y CRC/Link B Error
Counter
C CRC/Link B Error
Counter
Y CRC/Link A Error
Counter
C CRC/Link A Error
Counter
CRC Error Counter
Clear
Y CRC/Link B Error Counter
C CRC/Link B Error Counter
Y CRC/Link A Error Counter
C CRC/Link A Error Counter
CRC Error Counter Clear
VI Output (AFD)
VI Output (Scan)
WSS Detect Line
WSS Present
WSS Control
WSS Embed Line
WSS Select
WSS Output
WSS Detect Line
WSS Present
WSS Control
WSS Embed Line
WSS Select
WSS Output
36 Chapter 3
Operation
Changing Parameter Settings
You can change parameter settings at the card edge. You can change the parameter settings, view read-only parameters, view alarms, and adjust alarm settings using CCS software. See the following topics:
Changing Parameter Settings Using Card-Edge Controls on page 36
Changing Parameter Settings Using CCS Software on page 38
Changing Parameter Settings Using Card-Edge Controls
1 Rotate the hex switch (mode select rotary switch) to 0 .
2 Once the hex switch is set to “0,” toggle the navigation switch up or down to select a bank.
View the two control LEDs next to the navigation toggle switch to see which bank is
currently selected. (See Table 3-9 .)
See
to view the various banks, hex switch positions, and corresponding parameter options and values.
Table 3-9 Selected Bank as Indicated by Control LEDs
7
8
9
A (10)
B (11)
C (12)
D (13)
E (14)
F (15)
5
6
3
4
1
2
Bank Number
0
LED 3
Off
Off
Off
Off
Off
Off
Off
Off
On
On
On
On
On
On
On
On
Off
On
On
On
On
On
Off
Off
Off
Off
On
On
On
LED 2
Off
Off
Off
On
Off
Off
On
On
On
Off
Off
On
On
Off
Off
On
LED 1
Off
Off
On
LED 0
Off
On
Off
On
Off
On
Off
On
Off
On
Off
On
Off
On
Off
On
3 Rotate the hex switch to the parameter number (1 to 9) or letter (A to F) of the option you want to set.
4 Toggle the navigation switch to select and set the value of the chosen parameter.
5 Do either of the following:
Rotate the hex switch to another parameter number/letter in the current bank, and then repeat step 4.
HMX6803
+
and OP
+
HMX
+
Installation and Operation Manual
37
Rotate the hex switch to “0” again to select a different bank, and then repeat steps 3 and 4.
Use an available 6800
+
software control option to aid in viewing, setting, and confirming the parameter value.
Recalling Factory Default Parameter Settings
Parameters on page 39 describes all of the parameter
settings for HMX6803
+
and OP
+
HMX
+
modules, including the original factory defaults. To return this module to its factory default settings, you can either reset each parameter individually or do a global recall following this procedure.
1 Rotate the hex switch to 0 .
2 Toggle the navigation switch to the bank number 0 .
3 Use the control LEDs to verify which bank you have selected, or use an available 6800
+ software control option (serial/local or Ethernet/remote) to aid in confirming your bank selection.
4 Rotate the hex switch to the global recall parameter F .
5 Toggle the navigation switch to On .
Use an available 6800
+
software control option to aid in viewing, setting, and confirming the parameter value.
Reading Software and Hardware Versions
The current software version of your module can viewed using a HTTP browser, a
CCS-enabled control panel, or a CCS software application, such as Pilot or Navigator. To determine the hardware version number for HMX6803
+
and OP
+
HMX
+
modules, follow these steps:
In CCS Navigator,
1 Discover the frame that contains the module, and save results of your discovery.
2 In the Navigation pane, right-click on the module and select Configuration .
3 In the Configuration dialog box, select the Version tab.
4 In the Item Name list, look at the Hardware menu item. If it is expandable and provides a version number, then the revised specifications apply to your module. If the Hardware menu item is non-expandable and provides no version information, then the original specifications apply.
In an internet browser,
1 Enter the IP address of the frame that contains the module.
2 In the Navigation pane, click on the module to expand its menu, and then select
Configuration > Version .
If the Hardware item displays a version number, then the revised specifications apply to your module. If the Hardware menu item provides no version information, then the original specifications apply.
38 Chapter 3
Operation
Changing Parameter Settings Using CCS Software
Before using CCS Navigator to change your module’s parameter settings, you must discover the module. Discovery is the process by which CCS Navigator finds, and then connects to your module.
Identifying Your Module in CCS Software
Whether your module is a HMX6803
+
or an OP
+
HMX
+
, when you discover it in CCS
Navigator or refresh it in
+
Pilot Lite, the module will be identified as a HMX6803
+
.
If your module has an optional laser OP
+
HMX
+
component, the Laser Wavelength parameter displays the wavelength. If the module does not have an optical component, the
Laser Wavelength parameter displays Not Installed .
In addition, if the module is an OP
+
HMX
+
, it will have one additional alarm that standard
HMX6803
+
modules do not. This alarm is Laser Failed .
Discovering Your Module Using CCS Software
To discover your module, your Navigator software must be in Build mode.
1 If the Discovery window is not open, click Tools > Discovery in the main menu.
A Discovery window opens, most likely in the bottom left corner of the screen.
2 Click Options , and then click Add .
3 Enter the IP address of the frame that contains your module, the frame that contains your
ICE6800
+
module, or the frame that contains a 6800
+
ETH module that provides access to your module.
4 Click OK to close the Add Host dialog box, and then OK again to close the Discovery
Options dialog box.
5 Click Start .
This triggers Navigator to run a discovery.
Discovery Completed is displayed in the Discovery pane.
6 Click Save to save the results of your discovery to the Discovery folder of the Navigation pane.
7 Switch to Control mode by selecting Operational Mode > Control from the main menu.
8 Double-click HMX6803
+
in the Navigation pane.
The Control window opens displaying the module’s controls.
You can now switch to Control mode by selecting Operational Mode > Control from the main menu. Double-click HMX6803
+
in the Navigation pane (OP
+
HMX
+
modules are also referred to as HMX6803
+
in the Navigator pane). The Control dialog box opens displaying the module’s controls.
Setting HMX6803
+
Remote Control Parameters
Table 3-10 lists all of the remote control parameters and options for the HMX6803
+
. To access these parameters, you can use CCS Navigator, an HTTP web browser, or a third-party
SNMP-based control application (depending on your host frame’s options). See your software user manual for more information.
HMX6803
+
and OP
+
HMX
+
Installation and Operation Manual
39
Note that rows in the table that contain a range of numbers in parentheses indicate that a series of numbered parameters contain that same function and range.
Legend
Bold option=Indicates that this is the default setting for the parameter.
Rows of the table that are in grey are read-only parameters.
All parameters clip unless otherwise indicated.
Table 3-10 HMX6803
+
and OP
+
HMX
+
Parameters
Path Parameter Name
Bank/
Switch
Function
General
Serial Number
License Key
Installed Options
Factory Recall
Global Audio Phase
Reset
0, F
Options or User Range
Displays the module’s unique identifier
Activates options
(string)
String
Displays activated options 3G
Recalls the factory default settings
No
Yes
Resets the audio phase across all audio channels
No
Yes
Laser Wavelength
Product Information
Shows the wavelength of the laser submodule if the module is an OP
+
HMX
+
; if the module is a
HMX6803
+
, this parameter displays Not
Installed
String
Reports the full module name (for OP
+
HMX
+ modules only)
String
Serial Port
Metadata Interface
Type
12, 8 Selects the metadata interface type
RS-232
RS-422
40 Chapter 3
Operation
Table 3-10 HMX6803
+
and OP
+
HMX
+
Parameters (Continued)
Path Parameter Name
Bank/
Switch
Function
Input > SDI
SDI Video Standard
Set
0, 1
Options or User Range
Selects the SDI video signal standard
** Standards are available with the optional 3G HD license only.
Auto
525i 59.94
625i 50
1080i 50 (295M)
1080i 60
1080i 59.94
1080i 50
1080p 30
1080p 29.97
1080p 25
1080p 24
1080p 23.98
1080psf 24
1080psf 23.98
720p 60
720p 59.94
720p 50
1080p 60**
1080p 59.94**
1080p 50**
1080p 60 DL**
1080p 59.94
DL**
1080p 50 DL**
SDI Electrical IP
Present
SDI Electrical IP Video
Std Fb
Y CRC/Link B Error
Counter
Reports the presence of the SDI input video signal
Reports the detected SDI video signal standard
No
Yes
Unknown
1080p 25
720p 59.94
720p 60
1080p 23.98
1080p 24
1080p 29.97
1080p 30
1080i 50
1035i 59.94
1035i 60
1080i 50 (295M)
1080i 59.94
1080i 60
525i 59.94
0 to 16777215
625i 50
720p 50
1080psf 23.98
1080psf 24
720p 29.97
720p 30
720p 25
720p 23.98
720p 24
1080p 50
1080p 59.94
1080p 60
1080p 50 DL
1080p 59.94 DL
1080p 60 DL
C CRC/Link B Error
Counter
Reports the number of luminance CRC errors that have occurred
Reports the number of chrominance CRC errors that have occurred
0 to 16777215
Y CRC/Link A Error
Counter
Reports the number of luminance CRC errors that have occurred
0 to 16777215
HMX6803
+
and OP
+
HMX
+
Installation and Operation Manual
41
Table 3-10 HMX6803
+
and OP
+
HMX
+
Parameters (Continued)
Path Parameter Name
Bank/
Switch
Function
C CRC/Link A Error
Counter
Reports the number of chrominance CRC errors that have occurred
CRC Error Counter
Clear
0, 4 Clears all CRC error counters
Options or User Range
0 to 16777215
No
Yes
0 to 16777215 Y CRC/Link B Error
Counter
EDH Error Counter
Clear
EDH Present
525 VBI Duration
0, 5
Reports the number of luminance CRC errors that have occurred
Clears the EDH error counter
Reports the presence of
EDH in the input SDI signal
Reports if the VBI duration in 525i 59.94 is normal or short
No
Yes
No
Yes
Normal
Short
Input > Genlock/DARS
DARS Present Reports the presence of the DARS reference signal
No
Yes
DARS Locked to
Video
Reports the locked status of the DARS input signal
Input > Audio > Analog (HMX6803
+
AI
+
T and OP
+
HMX
+
AI
+
T only)
No
Yes
Analog Audio Input
CH (1A-4B) Level
Reports the dBFS operational level for the specified analog audio input channel
10 dBu - 28 dBu ( 24 dBu )
Input > Audio > AES
Input AES (1–8)
Present
Reports the presence of the specified AES input signal
Yes
No
42 Chapter 3
Operation
Table 3-10 HMX6803
+
and OP
+
HMX
+
Parameters (Continued)
Path Parameter Name
Bank/
Switch
Function
Input > Audio > Routing
SRC(1–16) Input
Select
0, 7
0, E
Selects the input audio source for the specified
Channel’s Sample Rate
Converter
1, 1
1, 8
Options or User Range
DMX Grp1 Ch1/2 (Default for SRC1)
DMX Grp1 Ch3/4 (Default for SRC2)
DMX Grp2 Ch1/2 (Default for SRC3)
DMX Grp2 Ch3/4 (Default for SRC4)
DMX Grp3 Ch1/2 (Default for SRC5)
DMX Grp3 Ch3/4 (Default for SRC6)
DMX Grp4 Ch1/2 (Default for SRC7)
DMX Grp4 Ch3/4 (Default for SRC8)
AES1a/1b (Default for SRC9)
AES2a/2b (Default for SRC10)
AES3a/3b (Default for SRC11)
AES4a/4b (Default for SRC12)
AES5a/5b (Default for SRC13)
AES6a/6b (Default for SRC14)
AES7a/7b (Default for SRC15)
AES8a/8b (Default for SRC16)
Analog 1a/1b (HMX6803
+
AI
+
T and
OP
+
HMX
+
AI
+
T only)
Analog 2a/2b (HMX6803
+
AI
+
T and
OP
+
HMX
+
AI
+
T only)
Analog 3a/3b (HMX6803
+
AI
+
T and
OP
+
HMX
+
AI
+
T only)
Analog 4a/4b (HMX6803
+
AI
+
T and
OP
+
HMX
+
AI
+
T only)
Input > Audio > V-bit
V-bit Mute Enable 4, C Enables automatic muting of audio outputs when the V-bit is set
Note Muting on a detected
V-Bit applies to PCM audio channels only. Non-PCM audio channels will not be muted.
Reports the validity bit status of the specified audio channel
No
Yes
Off
On
Aud Ch(1-32)
(SRC1a-16b) V-bit
Status
Input > Audio > Format
Aud Ch(1-32)
(SRC1a-16b) Format
1, 9
3, A
Selects the AES format
(Auto/PCM/Non-PCM) of the selected input audio channel
Auto
PCM
Non-PCM
HMX6803
+
and OP
+
HMX
+
Installation and Operation Manual
43
Table 3-10 HMX6803
+
and OP
+
HMX
+
Parameters (Continued)
Path Parameter Name
Bank/
Switch
Function
Input > Audio > Status
Input AES (1A–8B)
Status
Input Analog Audio
Ch (1A - 4B) Status
Options or User Range
Reports the current status of the specified audio input channel
Reports the current status of the specified analog audio input channel
(HMX6803
+
AI
+
T and
OP
+
HMX
+
AI
+
T only)
Normal
Silence
Peak
Not Present
Normal
Silence
Peak
Not Present
Input > Metadata
Embedded Metadata
Present
External Metadata
Present
Reports the presence of embedded metadata
Reports the presence of external metadata
No
Yes
No
Yes
Input > AFD / VI / WSS De-embedder
AFD Present Indicates the presence of
AFD packets
VI Scan Present Indicates the presence of
VI packet Scan Part (526/
625 only)
None
UNDEF
RSVD
16:9 top
14:9 top
>16:9 in 4:3
4:3 full
16:9 l
14:9 l
4:3 a 14:9
16:9 l a 14:9
None
NO INFO
525 4:3
625 4:3
16:9 l a 4:3
16:9 full
14:9 cntr
>16:9 in 16:9
16:9 full
4:3 p
16:9 prtctd
14:9 p
4:3 p a 14:9
16:9 a 14:9
16:9 a 4:3
RSVD
525 16:9
625 16:9
44 Chapter 3
Operation
Table 3-10 HMX6803
+
and OP
+
HMX
+
Parameters (Continued)
Path Parameter Name
Bank/
Switch
Function
VI AFD Present
VI Detect Line Fld 1
VI Detect Line Fld 2
WSS Present
Options or User Range
Indicates the presence of
VI packet AFD Part (526/
625 only)
None
UNDEF
RSVD
16:9 top
14:9 top
>16:9 in 4:3
4:3 full
16:9 l
16:9 l a 4:3
16:9 full
14:9 cntr
>16:9 in 16:9
16:9 full
4:3 p
16:9 prtctd
14:9 p
14:9 l
4:3 a 14:9
4:3 p a 14:9
16:9 a 14:9
16:9 l a 14:9 16:9 a 4:3
12 to 19 (525 Input) ( 14 )
8 to 22 (625 Input) ( 11 )
Controls the video line number to detect VI packet embedded in field
1 (526/625 only)
Controls the video line number to detect VI packet embedded in field
2 (526/625 only)
275 to 282 (525 Input) ( 277 )
321 to 335 (625 Input) ( 324 )
Indicates the presence of
WSS packet (625 only)
None
Full frame
14:9 center
14:9 top
16:9 center
16:9 top
>16:9
Full a 14:9
16:9 Anamorphic
WSS Detect Line Controls the video line number to detect WSS packet embedded in field
1 (625 only)
8 to 23
Processing > Audio
Audio Control Style
Fade Rate
ADS Clean
Audio V-Fade
Seamless Sound
Enable
7, 7
12, A
14, A
14, 9
Switches between Mono and Stereo control styles
Mono
Stereo
Controls the rate of fading when channels are swapped or muted
0.0 s to 10.0 s ( 0.1 s )
Cleans the Ancillary Data
Space prior to audio embedding
No
Yes
Disables audio V-fade
(clean audio hotswitch)
Enables seamless sound functionality
Disable
Enable
Disable
Enable
HMX6803
+
and OP
+
HMX
+
Installation and Operation Manual
45
Table 3-10 HMX6803
+
and OP
+
HMX
+
Parameters (Continued)
Path Parameter Name
Bank/
Switch
Function
Audio LOV Output
Mode
12, 5 Selects the output audio mode when the input video is disrupted
Processing > Audio > Sample Rate Conversion
SRC (1–16) Control 3, B
4, B
Controls insertion of the audio sample rate converter in the processing path
SRC (1–16) Status Reports the state of the specified sample rate converter
Processing > Audio > Delay
Delay Lock 5, 4
Aud Ch (1–2)
(SRC1a–1b) Delay
SRC1 Ext Audio Align
Aud Ch (3–4)
Aud Ch (5–6)
Aud Ch (7–8)
(SRC2a–2b) Delay
SRC2 Ext Audio Align
(SRC3a–3b) Delay
SRC3 Ext Audio Align
(SRC4a–4b) Delay
SRC4 Ext Audio Align
Aud Ch (9–10)
(SRC5a–5b) Delay
SRC5 Ext Audio Align
Aud Ch (11–12)
(SRC6a–6b) Delay
5, 5
5, 6
5, 7
5, 8
5,9
5, A
5, B
5, C
5, D
5, E
5, F
6, 1
Options or User Range
Pass
Mute
Auto
Enable
Bypass
Enabled
Bypassed
Couples fixed delay controls
No
Yes
Adjusts delay for the specified audio channel
Provides audio-video alignment for SRC1 when externally processed
0.000 ms to
1320.000 ms
Off
On
Adjusts delay for the specified audio channel
Provides audio-video alignment for SRC2 when externally processed
0.000 ms to
1320.000 ms
Off
On
Adjusts delay for the specified audio channel
Provides audio-video alignment for SRC3 when externally processed
0.000 ms to
1320.000 ms
Off
On
Adjusts delay for the specified audio channel
Provides audio-video alignment for SRC4 when externally processed
0.000 ms to
1320.000 ms
Off
On
Adjusts delay for the specified audio channel
Provides audio-video alignment for SRC5 when externally processed
0.000 ms to
1320.000 ms
Off
On
Adjusts delay for the specified audio channel
0.000 ms to
1320.000 ms
46 Chapter 3
Operation
Table 3-10 HMX6803
+
and OP
+
HMX
+
Parameters (Continued)
Path Parameter Name
Bank/
Switch
Function
SRC6 Ext Audio Align
Options or User Range
Provides audio-video alignment for SRC6 when externally processed
Off
On
Aud Ch (13–14)
(SRC7a–7b) Delay
SRC7 Ext Audio Align
6, 2
6, 3
Adjusts delay for the specified audio channel
Provides audio-video alignment for SRC7 when externally processed
0.000 ms
Off
On
to
1320.000 ms
Aud Ch (15–16)
(SRC8a–8b) Delay
SRC8 Ext Audio Align
6, 4
6, 5
Adjusts delay for the specified audio channel
Provides audio-video alignment for SRC8 when externally processed
0.000 ms
Off
On
to
1320.000 ms
Aud Ch (17–18)
(SRC9a–9b) Delay
SRC9 Ext Audio Align
6, 6
6, 7
Adjusts delay for the specified audio channel
Provides audio-video alignment for SRC9 when externally processed
0.000 ms
Off
On
to
1320.000 ms
Aud Ch (19–20)
(SRC10a–10b) Delay
SRC10 Ext Audio
Align
6, 8
6, 9
Adjusts delay for the specified audio channel
Provides audio-video alignment for SRC10 when externally processed
0.000 ms
Off
On
to
1320.000 ms
Aud Ch (21–22)
(SRC11a–11b) Delay
SRC11 Ext Audio
Align
6, A
6, B
Adjusts delay for the specified audio channel
Provides audio-video alignment for SRC11 when externally processed
0.000 ms
Off
On
to
1320.000 ms
Aud Ch (23–24)
(SRC12a–12b) Delay
SRC12 Ext Audio
Align
6, C
6, D
Adjusts delay for the specified audio channel
Provides audio-video alignment for SRC12 when externally processed
0.000 ms
Off
On
to
1320.000 ms
Aud Ch (25–26)
(SRC13a–13b) Delay
SRC13 Ext Audio
Align
6, E
6, F
Adjusts delay for the specified audio channel
Provides audio-video alignment for SRC13 when externally processed
0.000 ms
Off
On
to
1320.000 ms
Aud Ch (27–28)
(SRC14a–14b) Delay
7, 1
7, 2
Adjusts delay for the specified audio channel
0.000 ms to
1320.000 ms
HMX6803
+
and OP
+
HMX
+
Installation and Operation Manual
47
Table 3-10 HMX6803
+
and OP
+
HMX
+
Parameters (Continued)
Path Parameter Name
Bank/
Switch
Function
SRC14 Ext Audio
Align
Provides audio-video alignment for SRC14 when externally processed
Aud Ch (29–30)
(SRC15a–15b) Delay
7, 3
7, 4
Adjusts delay for the specified audio channel
SRC15 Ext Audio
Align
Aud Ch (31–32)
(SRC16a–16b) Delay
SRC16 Ext Audio
Align
7, 5
7, 6
Provides audio-video alignment for SRC15 when externally processed
Adjusts delay for the specified audio channel
Provides audio-video alignment for SRC16 when externally processed
Processing > Audio > Input Gain
Aud Ch (1- 8) (SRC1a
- 4b) Gain
Adjusts input gain for the specified audio channel
Options or User Range
Off
On
0.000 ms to
1320.000 ms
Off
On
0.000 ms to
1320.000 ms
Off
On
-36.0 dB to 36.0 dB ( 0.0 dB )
Processing > Audio > Test Tones
Test Tone 400 Hz
Level
7, 8
Test Tone 1 kHz Level 7, 9
Test Tone 2 kHz Level 7, A
Test Tone 4 kHz Level 7, B
Sets the tone amplitude -36.0 dBFS to 0.0 dBFS (
Processing > Audio > Output Gain
Gain Lock Couples the gain controls No
Yes
Processing > Audio > Output Gain > Embedded Audio
Output Emb Ch (1 -
16) Gain
Adjusts gain for the specified output embedded audio channel
-36.0 dB to 36.0 dB
( 0.0 dB )
Processing > Audio > Invert > Embedded Audio
Output Emb Ch (1 -
16) Invert
Inverts the selected audio channel to correct for phase error
No
Yes
Processing > Audio > Mute
Master Mute 7, C Enables muting for all output audio channels
Off
On
18.0 dBFS )
48 Chapter 3
Operation
Table 3-10 HMX6803
+
and OP
+
HMX
+
Parameters (Continued)
Path Parameter Name
Bank/
Switch
Function
Processing > Audio > Mute > Embedded Audio
Output Emb Ch (1 -
16) Mute
Enables muting for specified output embedded audio channel
Processing > Audio > Embedding
Dolby-E Start Line 12, 9
Audio Group (1-4)
Exists
Audio Group (1–4)
Embedding Mode
12, B
12, E
14, E
Options or User Range
Off
On
Specifies the starting video line of embedded
Dolby bitstreams
Reports the presence of the specified audio group in the SDI stream
15 to 54 (1080p, 1080i, and 1080psf formats) ( 19 )
20 to 71 (720p formats) ( 25 )
13 to 25 (525i 59.94 format) ( 15 )
9 to 30 (625i 50 format) ( 11 )
No
Yes
Selects the embedding mode for the specified audio group
Append (when ADS Clean is set to On)
OverWrt
Auto (when ADS Clean is set to Off)
Audio Group (1–4)
Pair (1–2) Embed
Control
Enables embedding of the selected pair in the audio group
Disable
Enable
15, 6
Group 1 Append
Embedding Error
No
Yes
Group 1 Overwrite
Embed Error
Group 2 Append
Embedding Error
Group 2 Overwrite
Embed Error
Group 3 Append
Embedding Error
Group 3 Overwrite
Embed Error
Reports if an append embedding error has occurred in the group 1 embedder
Reports if an overwrite embedding error has occurred in the Group 1 embedder
Reports if an append embedding error has occurred in the group 2 embedder
Reports if an overwrite embedding error has occurred in the group 2 embedder
Reports if an append embedding error has occurred in the group 3 embedder
Reports if an overwrite embedding error has occurred in the group 3 embedder
No
Yes
No
Yes
No
Yes
No
Yes
No
Yes
HMX6803
+
and OP
+
HMX
+
Installation and Operation Manual
49
Table 3-10 HMX6803
+
and OP
+
HMX
+
Parameters (Continued)
Path Parameter Name
Bank/
Switch
Function
Group 4 Append
Embedding Error
Reports if an append embedding error has occurred in the group 4 embedder
Group 4 Overwrite
Embed Error
Reports if an overwrite embedding error has occurred in the group 4 embedder
Processing > Metadata
Metadata
Embedding Enable
12, 6
Metadata
Embedding DID
Metadata
Embedding SDID
Metadata
Embedding Line
Number
12, 7
Options or User Range
No
Yes
No
Yes
Enables embedding of metadata
Selects the DID to use when embedding metadata
Disable
Enable
0x45
0x50
Selects the SDID to use when embedding metadata
1 to 9
Controls the line to which metadata packets will be embedded
Note 1080p (50/59.94/60) ranges apply with the optional 3G HD license only.
9 to 41 (1080p) (13)
9 to 25 (720p) (13)
9 to 20 (1080i) (13)
12 to 19(525i 59.94) (13)
8 to 22 (625i 50) (13)
Processing > Video
Loss Of Video Output
Mode
14, 2 Selects the output video mode when the input video is disrupted
Black
Grey
Processing > Video > Delay
Video Delay Bypass 13, C Controls insertion of the video delay circuit into the signal processing path
No
Yes
50 Chapter 3
Operation
Table 3-10 HMX6803
+
and OP
+
HMX
+
Parameters (Continued)
Path Parameter Name
Bank/
Switch
Function
Horizontal Phase
Vertical Phase
Video Delay
Audio/Video Align
14, 3
14, 4
14, 5
14, 6
Options or User Range
Adjusts the horizontal timing
Note: 1080p (50/59.94/60) ranges apply with the optional 3G HD license only.
Adjusts the vertical timing
Note: 1080p ranges apply with the optional 3G HD license only.
Controls the amount of video delay in frames
Provides a fixed delay to the video processing path to compensate for audio processing delay
0.000 us to 29.616 us (1080p30, 1035i
60, 1080i 60)
0.000 us to 14.808 us (1080p 60)
0.000 us to 29.646 us (1080p 29, 1035i
59, 1080i 59)
0.000 us to 14.823 us (1080p 59)
0.000 us to 35.542 us (1080p 25, 1080i
25)
0.000 us to 17.771 us (1080p 50)
0.000 us to 37.024 us (1080p 24,
1080psf 2)
0.000 us to 37.061 us (1080p 23,
1080psf23)
0.000 us to 31.987 us (1080i 25_295)
0.000 us to 22.209 us (720p60)
0.000 us to 22.231 us (720p50)
0.000 us to 26.653 us (720p50)
0.000 us to 44.431 us (720p30)
0.000 us to 44.475 us (720p29)
0.000 us to 53.320 us (720p25)
0.000 us to 63.518 us (525i 59.94)
0.000 us to 63.963 us (625i 50)
0 to 1124 lines (1080p/i/psf)
0 to 1249 lines
(1080i 25_295M)
0 to 749 lines (720p)
0 to 524 lines (525i 59.94)
0 to 624 lines (625i 50)
0 -8 frames (HD sync mode)
0 -10 frames (HD delay mode)
0 -50 frames (SD)
No
Yes
Actual Video Delay
Used
External Audio Delay
Reports the actual video delay in frames
0 frm to 100 frm
Represents the amount of audio processing delay external to the module
0 ms to 2000 ms
HMX6803
+
and OP
+
HMX
+
Installation and Operation Manual
51
Table 3-10 HMX6803
+
and OP
+
HMX
+
Parameters (Continued)
Path Parameter Name
Bank/
Switch
Function
Processing > Video > Processing Amplifier
Video ProcAmp
Enable
12, F Enables the video processing amplifier
Options or User Range
Y Gain
Cb Gain
Cr Gain
Y Offset
Cb Offset
Cr Offset
White Clip Enable
White Clip Level
Black Clip Enable
Black Clip Level
Hue
13, 1
13, 2
13, 3
13, 4
13, 5
13, 6
13, 7
13, 8
13, 9
13, A
13, B
Adjusts gain for the Y channel
Adjusts gain to the Cb color difference component
Adjusts gain to the Cr color difference component
Adjusts offset for the Y channel
Adjusts offset for the Cb channel
Adjusts offset for the Cr channel
Controls level clipping according to the White
Clip Level control
Sets the white clip level
Controls level clipping according to the Black
Clip Level control
Sets the black clip level
Adjusts the hue of the incoming digital video signal
No
Yes
-3.0 to +3.0 dB ( dB dB dB
)
-3.0 to +3.0 dB (
)
-3.0 to +3.0 dB (
±100.6 mV (
±100.6 mV (
±100.6 mV (
0
0
636.9 to 763.1 mV (
)
Disable
Enable
Disable
Enable
0
0 mV
0 mV
0 mV )
)
)
-47.9 to +47.9 mV (
-180 to +180° (0° )
Processing > Video > Test Pattern Generator
Test Pattern Select
Test Pattern Enable
14, 7
14, 8
Selects the test pattern to display
Enables the internal test pattern generator
75% color Bars
Pathological
100% color Bars
Off
On
Processing > Video > VBI
VBI Control Type
VBI Line (746–750)
Delete
Provides a master control for the VBI line processing
Deletes to black the active video portion of the selected VBI line (720p output only)
Individual
Set All Pass
Set All Delete
Off
On
700 mV
0.0 mV
)
)
EQ Pathological
PLL Pathological
52 Chapter 3
Operation
Table 3-10 HMX6803
+
and OP
+
HMX
+
Parameters (Continued)
Path Parameter Name
Bank/
Switch
Function
VBI Line (1122–1123)
Delete
Options or User Range
Deletes to black the active video portion of the selected VBI line (1080p output only)
Off
On
VBI Line (1124–1125)
Delete
Deletes to black the active video portion of the selected VBI line (1080i/ psf, 1080p output only)
Off
On
VBI Line 6 Delete Deletes to black the active video portion of the selected VBI line (625,
1080p, 720p output only)
Off
On
VBI Line (7–9) Delete Deletes to black the active video portion of the selected VBI line (625,
1080i/psf, 1080p, 720p output only)
Off
On
VBI Line (10–20)
Delete
Deletes to black the active video portion of the selected VBI line (all standards)
Off
On
VBI Line (21–23)
Delete
Deletes to black the active video portion of the selected VBI line (525,
625, 1080p, 720p output only)
Off
On
VBI Line (24–25)
Delete
Deletes to black the active video portion of the selected VBI line (1080p,
720p output only)
Off
On
VBI Line (26–41) Deletes to black the active video portion of the selected VBI line (1080p output only)
Off
On
VBI Line (272–286)
Delete
Deletes to black the active video portion of the selected VBI line (525 output only)
Off
On
VBI Line (318–336)
Delete
Deletes to black the active video portion of the selected VBI line (625 output only)
Off
On
VBI Line (561–562)
Delete
Deletes to black the active video portion of the selected VBI line (1080i output only)
Off
On
HMX6803
+
and OP
+
HMX
+
Installation and Operation Manual
53
Table 3-10 HMX6803
+
and OP
+
HMX
+
Parameters (Continued)
Path Parameter Name
Bank/
Switch
Function
VBI Line (569–583)
Delete
Options or User Range
Deletes to black the active video portion of the selected VBI line (1080i output only)
Off
On
Processing > Video > AFD / VI / WSS
Out Aspect Ratio Sets the aspect ratio of SD output in auto ARCing control
4:3
16:9
Output > Audio Word Length > Embedded Audio
Audio Ch 1/2 Word
Length
Audio Ch 3/4 Word
Length
7, D
7, E
Adjusts the sample resolution for the selected output audio channel pair
24 bits (default for HD mode)
20 bits (default for SD mode)
16 bits
7, F Audio Ch 5/6 Word
Length
Audio Ch 7/8 Word
Length
8, 1
Audio Ch 9/10 Word
Length
8, 2
8, 3 Audio Ch 11/12
Word Length
Audio Ch 13/14
Word Length
8, 4
Audio Ch 15/16
Word Length
8, 5
54 Chapter 3
Operation
Table 3-10 HMX6803
+
and OP
+
HMX
+
Parameters (Continued)
Path Parameter Name
Bank/
Switch
Function Options or User Range
Output > Audio Source Select > Embedded audio
Output Emb Ch (1–
16) Source Select
8, E
9, E
Selects the source for the specified output channel
SRC1a
Default for each channel is the corresponding source -- for example, the default for Output Emb
Ch 9 Source Select is SRC
13a.
SRC8b
SRC1a+1b
SRC2a+2b
SRC3a+3b
SRC4a+4b
SRC5a+5b
SRC6a+6b
SRC7a+7b
SRC8a+8b
SRC9a (default for Output Emb Ch 1
Source Select)
SRC16b (default for Output Emb Ch 16
Source Select)
SRC9a+9b
SRC10a+10b
SRC11a+11b
SRC12a+12b
SRC13a+13b
SRC14a+14b
SRC15a+15b
SRC16a+16b
Test Tone 400Hz
Test Tone 1kHz
Test Tone 2kHz
Test Tone 4kHz
Mute
EBU R68
SMPTE RP155
SRC1a+2a
SRC1b+2b
SRC2a+3a
SRC2b+3b
SRC2a+4a
SRC2b+4b
HMX6803
+
and OP
+
HMX
+
Installation and Operation Manual
55
Table 3-10 HMX6803
+
and OP
+
HMX
+
Parameters (Continued)
Path Parameter Name
Bank/
Switch
Function Options or User Range
Output > Audio Format > Embedded audio
Output Emb Ch (1–
16) Format Feedback
Reports the AES format
(PCM/non-PCM) of specified output embedded audio channel
PCM
Non-PCM
Unknown
Output > Video Status
Output Video Frozen Reports the output video frozen status
No
Yes
Output > AFD /VI / WSS Embedder
AFD Control
AFD Embed Line
AFD Select
AFD Output
Controls the embedding of the AFD packet
Controls the video line number where the AFD packet gets embedded to in field 1
Remove
Insert Custom
Pass
Convert from VI (525/625 input only)
Convert from WSS (625 input only)
12 to 19 (525)
8 to 22 (625)
9 to 20 (1080i)
9 to 25 (720p)
9 to 41 (1080p)
Controls the AFD code that gets embedded
Indicates current AFD output code
When Out Aspect
Ratio is set to 4:3:
16:9 top
14:9 top
>16:9 in 4:3
4:3 full
16:9 l
14:9 l
4:3 a 14:9
16:9 l a 14:9
16:9 l a 4:3
None
16:9 top
14:9 top
>16:9 in 4:3
4:3 full
16:9 l
14:9 l
4:3 a 14:9
16:9 l a 14:9
When Out Aspect
Ratio is set to 16:9:
16:9 full
14:9 p
>16:9 in 16:9
4:3 p
16:9 prtctd
4:3 p a 14:9
16:9 a 14:9
16:9 a 4:3
16:9 l a 4:3
16:9 full
14:9 p
>16:9 in 16:9
4:3 p
16:9 prtctd
4:3 p a 14:9
16:9 a 14:9
16:9 a 4:3
56 Chapter 3
Operation
Table 3-10 HMX6803
+
and OP
+
HMX
+
Parameters (Continued)
Path Parameter Name
Bank/
Switch
Function
VI Control
VI Embed Line
Options or User Range
Controls the embedding of the VI packet (526/625 only)
Controls the video line number where the VI packet gets embedded to in field 1 (526/625 only)
Remove
Insert Custom
Convert from AFD
Pass
Convert from WSS (valid for 625 input only)
12 to 19 (525)
( 14 )
8 to 22 (625) ( 11 )
VI Select
SD Out VI with AFD
VI Output (AFD)
VI Output (Scan)
Controls the VI code that gets embedded (526/625 only)
Controls whether the VI output supports the AFD upper bits part
Indicates current VI output code AFD part
(526/625 only)
Indicates current VI output code Scan part
(526/625 only)
When Out Aspect
Ratio is set to 4:3:
16:9 top
14:9 top
>16:9 in 4:3
4:3 full
16:9 l
14:9 l
4:3 a 14:9
16:9 l a 14:9
16:9 l a 4:3
No
Yes
None
16:9 top
14:9 top
>16:9 in 4:3
4:3 full
16:9 l
14:9 l
4:3 a 14:9
16:9 l a 14:9
None
525 4:3
625 4:3
525 16:9
625 16:9
When Out Aspect
Ratio is set to 16:9:
16:9 full
14:9 p
>16:9 in 16:9
4:3 p
16:9 prtctd
4:3 p a 14:9
16:9 a 14:9
16:9 a 4:3
16:9 l a 4:3
16:9 full
14:9 p
>16:9 in 16:9
4:3 p
16:9 prtctd
4:3 p a 14:9
16:9 a 14:9
16:9 a 4:3
HMX6803
+
and OP
+
HMX
+
Installation and Operation Manual
57
Table 3-10 HMX6803
+
and OP
+
HMX
+
Parameters (Continued)
Path Parameter Name
Bank/
Switch
Function
WSS Control
WSS Embed Line
Options or User Range
Controls the embedding of the WSS packet (625 only)
Controls the video line number where the WSS packet gets embedded to in field 1 (625 only)
Remove
Insert Custom
Convert from AFD
Convert from VI
Pass
8 to 23
WSS Select
WSS Output
Custom On Loss
Controls the WSS code that gets embedded (625 only)
Indicates current WSS output code (625 only)
Controls whether to insert custom code when upstream code disappears in code bypass mode
Full frame
14:9 center
14:9 top
16:9 center
None
Full frame
14:9 center
14:9 top
16:9 center
No
Yes
16:9 top
>16:9 center
Full a 14:9
16:9 Anamorphic
16:9 top
>16:9 center
Full a 14:9
16:9 Anamorphic
LEDs and Alarms
Monitoring
LEDs
The HMX6803
+
and OP
+
HMX
+
have 11 monitoring LEDs that serve as quick monitoring
shows the location of the monitoring LEDs on an HMX6803
+
and
OP
+
HMX
+
module.
Table 3-11 describes each LED in more detail.
58 Chapter 3
Operation
Module status LED
Monitoring
Table 3-11 Monitoring LEDs
LED
AUTO
Color Indicators
Green
720P
1035I
1080P/SF
1080I
525
625
VID PRES ELECT
VID PRES FIBER
ELECT IN SEL
FIBER IN SEL
REF PRES
FREEZE
DARS PRES
AUDIO 1
AUDIO 2
AUDIO 3
AUDIO 4
Figure 3-10 Location of HMX6803
+
and OP
+
HMX
+
LEDs
Green
Green
Green
Green
Green
Green
Green
Green
Green
Green
Green
Yellow
Green
Green
Green
Green
Green
Meaning
Auto detection of the SD-SDI input standard is active
Selected video standard is 720p
Unused
Selected video standard is 1080p or 1080psf
Selected video standard is 1080i
Selected video standard is 525
Selected video standard is 625i 50
Electrical input video is present
Unused
Unused
Unused
Unused
Unused
Indicates presence of DARS
Presence of AES audio on AES input 1
Presence of AES audio on AES input 2
Presence of AES audio on AES input 3
Presence of AES audio on AES input 4
HMX6803
+
and OP
+
HMX
+
Installation and Operation Manual
59
Table 3-11 Monitoring LEDs (Continued)
LED
AUDIO 5
AUDIO 6
AUDIO 7
AUDIO 8
Color Indicators
Green
Green
Green
Green
Meaning
Presence of AES audio on AES input 5
Presence of AES audio on AES input 6
Presence of AES audio on AES input 7
Presence of AES audio on AES input 8
Module
Status LEDs
HMX6803
+
and OP
+
HMX
+
modules do not have any card-edge alarms. Instead, a module status LED on the corner of the module lights up if an error is detected. See
for the location of these LEDs, and Table 3-12 for a definition of the LED colors.
Note: If the LED is flashing red, please contact your Customer Service representative.
Table 3-12 Module Status LED Descriptions
LED Color Sequence Meaning
Off There is no power to the module; the module is not operational.
Green
Red
Flashing red
Amber
There is power to the module; the module is operating properly.
There is an alarm condition.
The module has detected a hardware/firmware fault.
The module is undergoing configuration.
Alarms
If a major or minor alarm is triggered within your HMX6803
+
and OP
+
HMX
+
module, the
Status LED lights red.
Alarms are usually logged and monitored within available software control applications (for example, CCS Navigator). You can only differentiate between major and minor alarms within a software control application. See the appropriate software control user manual or online help for more information.
60 Chapter 3
Operation
The following settings can be made for each alarm within Pilot or Navigator software.
Table 3-13 Alarm Options
Alarm Option Effect
Enable/Disable This option toggles between Enabled and Disabled.
If the alarm is Enabled , an alarm condition will generate an alarm; but if it is Disabled , the alarm condition will be ignored.
By default, all alarms are disabled.
Alarm priority
Trigger (s)
This setting determines whether a triggered alarm will be reported as major or minor. The range is 1–
10. A priority of 6 or higher is a major alarm, and a priority of 5 or lower is a minor alarm
This option determines how long an alarm condition must exist (in seconds) before the alarm is triggered.
If the alarm level is reached for less time than the
Trigger duration, the alarm will not trigger. Choose any duration from 0 to 7200 seconds (or 2 hours). If this option is set to 0 and the alarm condition exists for any period of time, the alarm will trigger.
Clear (s)
Ack
This option determines the amount of time the alarm condition must be in abatement in order for the alarm to be turned off. Choose any duration from 0 to 7200 seconds (or 2 hours). If this option is set to 0 and the alarm condition ceases for any period of time, the alarm will clear.
When an alarm is active, click this option to allow other users on the network to see that you have acknowledged the alarm.
Table 3-14 describes the specific alarms for the HMX6803
+
and OP
+
HMX
+
. You can only identify specific alarms using a software control application.
Table 3-14 Alarm Definitions
Alarm Name
Video Standard Mismatch
Unsupported Video Standard
Loss of Electrical SDI Input
Input AES (1A-8B) Silent
Input AES (1A-8B) Peak
Group (1–4) Append Embedding Error
Group (1–4) Overwrite Embedding Error
AES (1–8) In Missing
Output Video Frozen
V-Bit Mute On
Master Mute On
1
4
6
1
5
6
6
9
1
8
8
Alarm Option Default Settings
Priority Trigger
1 sec
1 sec
1 sec
30.0 s
0.0 s
2 sec
2 sec
2 sec
2 sec
0.0 s
0.0 s
Clear
2 sec
2 sec
2 sec
0.0 s
0.0 s
2 sec
2 sec
2 sec
2 sec
2.0 s
2.0 s
HMX6803
+
and OP
+
HMX
+
Installation and Operation Manual
61
Table 3-14 Alarm Definitions (Continued)
Alarm Name
Laser Failed
(OP
+
HMX
+
modules only)
Loss of AFD
Input Analog Audio (1A–4B) Peak
(HMX6803
+
AI
+
T and OP
+
HMX
+
AI
+
T only)
Input Analog Audio (1A–4B) Silence
(HMX6803
+
AI
+
T and OP
+
HMX
+
AI
+
T only)
5
1
1
Alarm Option Default Settings
Priority
6 (Major)
Trigger
1 sec
Clear
2 sec
0 sec
1 sec
1 sec
0 sec
2 sec
2 sec
62 Chapter 3
Operation
4
Specifications
Specifications and designs are subject to change without notice.
Inputs
SDI Video Inputs
Note: 3G HD-SDI video input specifications only apply if you have installed a HMX68OPT-3G license key.
Table 4-1 SDI Video Inputs
Item
Number
Standard
3G HD-SDI
Specification
1
1080p (SMPTE 424M)
1080p DL (SMPTE 372M)
Connector BNC (IEC169-8)
Impedance 75 Ω
1.5G HD-SDI
Specification
1
1080i/p (SMPTE 274M)
720p (SMPTE 296M)
BNC (IEC169-8)
75 Ω
SD-SDI Specification
1
SMPTE 259M-C, 270 Mbps,
525/625 component
BNC (IEC169-8)
75 Ω
63
64 Chapter 4
Specifications
Table 4-1 SDI Video Inputs
Item
3G HD-SDI
Specification
1.5G HD-SDI
Specification
Frame rate 1080p: 50, 59.94, 60 Hz 1080i/p: 23.98, 24, 25,
29.97, 30 Hz
720p: 50, 59.94, 60 Hz
> 15 dB from 5 MHz to 1485 MHz
Return loss > 15 dB from 5 MHz to
1485 MHz
>10 dB from 1485 MHz to 2970 MHz
Equalization Original modules:
Adaptive cable equalization for up to
230 ft (70 m) (typical) of
Belden 1694A coaxial cable
Revised modules and hardware revision 1.01:
Adaptive cable equalization for up to
459 ft (140 m) (typical) of Belden 1694A coaxial cable
Original modules: Adaptive cable equalization for up to
492 ft (150 m) (typical) of
Belden 1694A coaxial cable
Revised modules and hardware revision 1.01:
Adaptive cable equalization for up to 656 ft (200 m)
(typical) of Belden 1694A coaxial cable
SD-SDI Specification
525: 59.94 Hz
625: 50 Hz
> 15 dB up to 270 MHz
Adaptive cable equalization for up to 984 ft (300 m)
(typical) of Belden 8281 coaxial cable
AES/DARS Inputs
Table 4-2 AES Inputs
Item
Standard
Connector
Sensitivity
Impedance
Return loss
Common mode rejection
Input audio rate
Balanced/DARS Specification
(Requires External Balun)
AES 3
3-pin connector, female XLR with external balun
<200 mV
110 Ω ± 20% (0.1 to 6 MHz)
N/A
0 V to 7 V (0 kHz to 20 kHz)
Unbalanced/DARS
Specification
AES 3, SMPTE 276M
BNC (IEC 169-8)
<100 mV
75 Ω
> 25 dB, 0.1 to 6 MHz
N/A
32 kHz to 108 kHz (DARS 48 kHz only)
Maximum input signal 10 V pk-to-pk
Bits 16, 20, or 24
Channel status and user bit
32 kHz to 108 kHz (DARS 4 8kHz only) n/a
16, 20, or 24
Maintained, but professional mode, 48 kHz (see Appendix A for full details)
HMX6803
+
and OP
+
HMX
+
Installation and Operation Manual
65
Analog Audio Input (Analog Audio Enabled Modules Only)
Table 4-3 Analog Audio Input
Item
Number of inputs
Connector
Input audio level
Input impedance
CMRR
Linearity
Frequency response
THD
SNR
Specification
8 mono channels
Weidmuller 24-pin locking header-socket pair
28 dBu to 12 dBu for 0 dBFs
(adjustable in 1 dB increments)
High-Impedance or 600 Ω , jumper selectable
> 80 dB at 60 Hz, typical
< ±0.5 dB (to -100 dBFS)
< ±0.05 dB (20 Hz to 20 kHz), typical
> 100 dB (at -1 dBFS, 20 Hz to 20 kHz), typical
> 100 dB
Outputs
SDI Video Outputs
Note: 3G HD-SDI video output specifications only apply if you have installed a
HMX68OPT+3G license key.
Table 4-4 SDI Video Outputs
Item
Number
Standard
Frame rate
Connector
Impedance
3G HD-SDI Specification
4 processed
1080p (SMPTE 424M)
1080p DL (SMPTE 372M)
1080p: 50, 59.94, 60 Hz
BNC (IEC169-8)
75 Ω
1.5G HD-SDI Specification SD-SDI Specification
4 processed
1080i (SMPTE 274M)
720p (SMPTE 296M)
SMPTE 292M with SMPTE
299M embedded audio
1080i: 50, 59.94, 60
1080p: 23.98, 24, 25,
29.97, 30 Hz
1080psf: 23.98, 24 Hz
720p: 50, 59.94, 60 Hz
BNC (IEC 169-8)
75 Ω
4 processed
SMPTE 259M-C,
270 Mb/s, 525/625 component
525i 59.94
625i 50
BNC (IEC 169-8)
75 Ω
66 Chapter 4
Specifications
Table 4-4 SDI Video Outputs (Continued)
Item
Return loss
Signal level
D.C. offset
Rise and fall time
Overshoot
Jitter
Delay
3G HD-SDI Specification
> 15 dB from 5 MHz to
1485 MHz
>10 dB from 1485 MHz to
2970 MHz
800 mV ± 10%
0.0 V ± 0.5 V
1.5G HD-SDI Specification SD-SDI Specification
> 15 dB from 5 MHz to 1485
MHz
800 mV ± 10%
0.0 V ± 0.5 V
< 135 ps < 270 ps, within 100 ps of each other
< 10% of amplitude
>100kHz: < 0.3 UI (101 ps) pk-to-pk
>10 Hz: < 2.0 UI (675 ps) pk-to-pk
< 10% of amplitude
>100 kHz: < 0.2 UI
(135 ps) pk-to-pk
>10 Hz: < 1 UI
(675 ps) pk-to-pk
Up to 11 frames Up to 11 frames
> 15 dB up to 270 MHz
800 mV ± 10%
0.0 V ± 0.5 V
0.4–1.5 ns
< 10% of amplitude
< 0.2 UI (740 ps) pk-to-pk
Up to 50 frames
Laser Output (OP
+
HMX
+
Only)
OP
+
HMX
+
(C)xxD optical modules comply with laser product performance standards set by the Center for Devices and Radiological Health (except for deviations), pursuant to Laser
Notice No. 50, dated July 26, 2001. Additionally, OP
+
HMX
+
(C)xxD modules comply with the provisions of IEC 60825-1.
Table 4-5 Optical Specifications for Laser Modules
Laser Module
Model
OP
+
HMX
+
13D
OP
+
HMX
+
CxxD
Wavelength (nm)
1310
1270
1290
1310
1330
1350
1370
1430
1450
1470
1490
1510
1530
1550
1570
1590
1610
Output
Optical
Power
Pulse
Duration
Laser Product
Class/Laser
Radiation Class
-7 dBm typical Continuous 1/I
0 dBm typical
HMX6803
+
and OP
+
HMX
+
Installation and Operation Manual
67
Optical Port (OP
+
HMX
+
Only)
Table 4-6 Fiber Option Video Output
Item
Number of outputs
Connector
Specification
1
SC/PC per IEC 61754-4-1 (standard)
ST/PC per IEC 61754-2 (optional)
FC/PC per IEC 61754-13 (optional)
Table 4-7 Optical Port Performance Specifications - Output (Transmitter)
Item Min Typical Max
Fixed Wavelength Modules (OP
+
HMX
+
13D)
Peak wavelength (FP) 1290 nm 1310 nm 1340 nm
Spectrum width (RMS) (FP) 2 nm 4 nm
Conditions
Average output power (FP) -8 dBm -7 dBm -6 dBm
Multiple Wavelength Modules (OP
+
HMX
+
CxxD)
Peak wavelength (CWDM) n-3 nm n nm n+3 nm Peak wavelength n = 1270; 1290;
1310; 1330; 1350; 1370; 1430; 1450;
1470; 1490; 1510; 1530; 1550; 1570;
1590; 1610
-1 dBm 0 dBm +2 dBm Average output power
(CWDM)
All Modules
Extinction ratio
Optical rise time
Optical fall time
6 dB
-
-
8 dB
-
135 ps
-
135 ps
150 ps
2.1 GHz filter (4th order Bessel filter)
No filter, 20%~80%
No filter, 20%~80%
CAUTION: To prevent overload damage, ensure that you observe the following:
Before connecting any standard-sensitivity (PIN) optical receiver to a fiber network, ensure the power level is tested to fall within the published specifications of the receiver. Failure to verify optical power before connection will void the warranty.
To ensure error-free operation, the input power must be less than -7 Bm.
68 Chapter 4
Specifications
RS-232/
RS-422
Table 4-8 RS-232/RS-422
Item
Standard
Connector
Specification
Electrical specification EIA-232C
DB-9
232/422 switchable
Propagation Delay
Table 4-9 HMX6803
+
/HDX6803
+
System Video Propagation Delay
Note: Video delay is bypassed for these measurements
Video Format
3G
HD
SD
Video Path
HMX6803
+ electrical in to fiber out to HDX6803+ fiber in to electrical out
HMX6803
+
electrical path (SDI in to out)
HMX6803
+
electrical in to fiber out to HDX6803+ fiber in to electrical out
HMX6803
+
electrical path (SDI in to out)
HMX6803
+
electrical in to fiber out to HDX6803+ fiber in to electrical out
HMX6803
+
electrical path (SDI in to out)
Specification
3.10 µs
1.50 µs
5.8 µs
3.0 µs
33.7 µs
16.0 µs
Table 4-10 HMX6803
+
/HDX6803
+
System Audio Propagation Delay
Video Format Conditions Delay
When HDX6803
+
AES Output Source Selection parameter is set to Audio Proc
SD AES IN to AES OUT; SRCs ON 8.1 ms
HD
AES IN to AES OUT; SRCs OFF
AES IN to AES OUT; SRCs ON
2.3 ms
8.7 ms
3G
AES IN to AES OUT; SRCs OFF
AES IN to AES OUT; SRCs ON
3.0 ms
8.2 ms
AES IN to AES OUT; SRCs OFF 2.4 ms
When HDX6803
+
AES Output Source Selection is set to Demux Ch (Direct, SRC bypassed)
SD / HD / 3G AES IN to AES OUT; SRCs ON 4.7 ms
AES IN to AES OUT; SRCs OFF 1.8 ms
HMX6803
+
and OP
+
HMX
+
Installation and Operation Manual
69
Power Consumption
Table 4-11 Power Consumption Specifications
Module
HMX6803
+
and OP
+
HMX
+
Power Consumption
< 12 W
Start-Up
Time
The start-up time for HMX6803
+
and OP
+
HMX
+
modules is <10 seconds.
Operating Temperature
The operating temperature for HMX6803
+
and OP
+
HMX
+
modules is 41° to 113°F (5° to
45°C).
70 Chapter 4
Specifications
A
Audio Bit Manipulation
Overview
The tables in this appendix contain information on the manipulation of bits that occur when using HMX6803 + and OP + HMX + modules.
The following items are documented:
Manipulating Channel Status Bits (C-Bit) on page 72
Manipulating Validity and User Bits (V-Bit and U-Bit) on page 74
Identifying Audio Characteristics (Audio Sampling Frequency and Word
Table A-1 Description of Short Forms in the Appendix
RX Key
Y=Recognized
S=Recognized and stored, passed-through, or both
TX Key
N=Not recognized N=Not transmitted
Y=Transmitted
Sample Rate Indication Audio Word Length
Byte 0 Bits [6,7],
Byte 4 Bits [3,4,5,6]
[00,0100] = 96 kHz
[01,0000] = 48 kHz
[11,0000] = 32 kHz
[00,1000] = 24 kHz
[00,0101] = 88.2 kHz
[10,0000] = 44.1 kHz
[00,1001] = 22.05 kHz
Byte 2 Bits [0,1,2]
[000] = Maximum word length
20 bits (auxiliary bit use not indicated)
[001] = Maximum word length
24 bits (auxiliary bits used for audio)
Byte 2 Bits [3,4,5]
[100] = Encoded word length
=Maximum word length - 4 bits
[101] = Encoded word length
=Maximum word length - 0 bits
71
72 Appendix A
Audio Bit Manipulation
Manipulating Channel Status Bits (C-Bit)
Table A-2 Channel Status (C-Bits) Data Description
Byte
0
0
Bit
0
1
Function
[0] Consumer Use
[1] Professional Use
[0] Audio
[1] Non-Audio
S
S
RX TX
N
Y
N
Y
Y
Y
0
Remarks
RX ignores bit
TX sets bit to 1
RX sets up audio channel to pass data
(Gain=0 dB, Invert=off)
TX bit passed unmodified or forced, according to Output
Chxx Format and Out
Chxx Format Fb parameters
RX ignores bits
TX passed bits unmodified
0
0
1
1
2
2 to 4 [000] Not Indicated
[100] No Emphasis
[110] 50/15 µs
[111] CCITTJ17
5 [0] Locked
[1] Unlocked
6 to 7 [00] Not indicated
[01] 48 kHz
[10] 44.1 kHz
[11] 32 kHz
0 to 3 [0000] Not indicated
[0001] Two channel
[0010] Mono
[0011] Prim/sec
[0100] Stereo
[0101] to [1111] Undefined
4 to 7 [0000] Not indicated
[0001] 192 bit block
[0010] AES18 (HDLC)
[0011] User defined
[0100] to [1111] Undefined
0 to 2 [000] Aux. bit use is not indicated
[001] Aux. bit use is audio data
[010] Aux. bit use is co-ordination signal
[011] to [111] Undefined
Y
N
N
N
N
N
N
Y
N
N
Y
Y
N
N
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
N
N
N
N
N
N
N
Y
Y
Y
Y
N
N
N
N
S
S
S
S
S
S
S
S
S
N
N
RX ignores bits
TX sets bit to [0]
RX ignores bits
TX sets bits to [01]
RX ignores bits
TX sets bits to [0000]
RX ignores bits
TX passes bits unmodified
RX ignores bits
TX sets bits according to transmitted word length
HMX6803
+
and OP
+
HMX
+
Installation and Operation Manual
73
Table A-2 Channel Status (C-Bits) Data Description (Continued)
Byte
2
2
3
Bit Function
3 to 5 [000] Not indicated
[001] Max Length - 1
[010] Max Length - 2
[011] Max Length - 3
[100] Max Length - 4
[101] Max Length
[110] to [111] Undefined
6 to 7 [00] Alignment level not indicated
[01] Alignment to SMPTE RP155
[10] Alignment to EBU R68
[11] Reserved
0 to 6 Bit 7 = 0: Channel number
Bit 7 = 1: [0,1,2,3] Channel number
[4,5,6] Multi-channel mode
RX TX
N
N
N
N
N
N
N
N Y
Y
Y
N
N
N
N
N
N Y
3 N Y
4
4
7 [0] Undefined multi-channel mode
[1] Defined multi-channel mode
0 to 1 [00] Not a reference
[01] Grade 1 reference
[10] Grade 2 reference
[11] Undefined
2 Reserved
N
N
N
N
N
Y
N
N
N
Y
4 N Y
Remarks
RX ignores bits
TX sets bits according to transmitted word length
RX ignores bits
TX sets bits to [00]
RX ignores bits
TX sets bits to
[0000000]
RX ignores bits
TX sets bits to [0]
RX ignores bits
TX sets bits to [00]
RX ignores bits
TX sets bits to [0]
RX ignores bits
TX sets bits to [0000]
4
5
3 to 6 [0000] Not indicated
[1000] 24 kHz
[0100] 96 kHz
[1100] 192 kHz
[1001] 22.05 kHz
[0101] 88.2 kHz
[1101] 176.4 Hz
[1111] User defined
7 [0] Sample frequency not scaled
[1] Sample frequency scaled by 1/
1.001
0 to 7 Reserved
N
N
Y
Y
RX ignores bits
TX sets bits to [0]
6 to 9
10 to 13
0 to 7
0 to 7
Alphanumeric channel origin data
Alphanumeric channel destination data
S
S
Y
Y
RX ignores bits
TX sets bits to
[00000000]
RX ignores bits
TX passed bits unmodified
RX ignores bits
TX passed bits unmodified
74 Appendix A
Audio Bit Manipulation
Table A-2 Channel Status (C-Bits) Data Description (Continued)
Byte Bit Function
14 to 17 0 to 7 Local sample address code
RX TX
S Y
18 to 21
22
22
22
22
22
23
0 to 7
0 to 3
4
5
6
7
0 to 7
Time-of-day sample address code
Reserved
Bytes 0 to 5 reliability flag
Bytes 6 to 13 reliability flag
Bytes 14 to 17 reliability flag
Bytes 17 to 21 reliability flag
CRC
S
N
N
S
S
S
Y
Y
Y
Y
Y
Y
Y
Y
Remarks
RX ignores bits
TX passed bits unmodified
RX ignores bits
TX passed bits unmodified
RX ignores bits
TX passed bits unmodified
RX ignores bits
TX passed bits unmodified
RX ignores bits
TX passed bits unmodified
RX ignores bits
TX passed bits unmodified
RX ignores bits
TX passed bits unmodified
RX ignores bits
TX calculates CRC on output
Manipulating Validity and User Bits (V-Bit and U-Bit)
Table A-3 V-Bit and U-Bit Data Descriptions
Item
Validity (V) bit
User (U) bit
RX
S
S
TX
Y
Y
Remarks
RX optionally mutes data if enabled
TX passes bit unmodified
RX ignores bits
TX passed bits unmodified
Identifying Audio Characteristics
(Audio Sampling Frequency and Word Length)
Table A-4 Audio Sampling Frequency and Word Length
Item
Audio sampling frequency
Audio word length
Remarks
RX: 32 to 108 kHz
TX: 48 kHz
RX: 16 to 24 bits
TX: 16 to 24 bits
HMX6803
+
and OP
+
HMX
+
Installation and Operation Manual
75
76 Appendix A
Audio Bit Manipulation
B
Laser Safety Guidelines
Laser
Safety
WARNING
Use of controls, adjustments, and procedures other than those specified in this document may result in hazardous laser radiation exposure.
Optical fiber telecommunication systems use semiconductor laser transmitters that emit infrared light that is normally not visible to the human eye. Although a conventional laser produces a small beam of light, the power density is very high, and it can cause damage to your eyes.
If a beam of laser light enters the eye, the eye magnifies and focuses the energy on the retina. The energy that reaches the retina can be as much as 100,000 times more than at the cornea and, as a result, it can burn the retina.
Laser transmission products are classified in four major groups (Class 1, 2, 3, and 4), according to their emissions and potential for causing injury. Fiber optic transmitter modules in this series are designated Class 1.
Precautions for Enclosed
Systems
In its normal operating mode, an optical fiber communication system is totally enclosed and presents no risk of eye injury. However, if the fiber optic cables that interconnect various components of an optical fiber disconnect or break, you may be exposed to laser emissions.
Also, technicians may be exposed to laser emissions during installation and servicing.
Unlike some other laser designs, semiconductor lasers have a highly divergent beam that decreases rapidly with distance. The greater the distance, the less energy will enter the eye, and the less potential risk for eye injury.
WARNING
Eye damage may occur if an optical instrument such as a microscope, magnifying glass, or eye loupe is used to stare at the energized fiber end.
Under normal operating conditions, optical fiber telecommunication systems are completely enclosed; nonetheless, observe the following precautions:
1 Do not stare into optical connectors or broken fibers.
77
78 Appendix B
Laser Safety Guidelines
2 Ensure technicians have satisfactorily completed an approved training course before performing installation or maintenance.
3 Ensure there are appropriate warning labels near the optical ports of the modules.
Precautions for
Unenclosed
Systems
During service, maintenance, or restoration, an optical fiber telecommunication system is considered unenclosed. Under these conditions, follow these practices:
CAUTION
Only authorized, trained personnel shall be permitted to do service, maintenance, and restoration.
1 Avoid exposing the eye to emissions from unterminated, energized optical connectors at close distances.
2 Ensure that only authorized, trained personnel use optical test equipment during installation or servicing.
3 Turn off all laser sources before scanning a fiber with an optical test set.
4 Keep all unauthorized personnel away from the immediate area of the optical fiber systems during installation and service.
For guidance on the safe use of optical fiber communication systems in the workplace, consult ANSI Z136.2, American National Standard for Safe Use of Lasers in the U.S., or outside the U.S., IEC-60825, Part 2 .
Labels
The label shown in
Figure B-1 is applicable to Class 1 laser products.
CLASS 1
LASER PRODUCT
Figure B-1 Label for Class 1 Laser Products
C
Communication and Control
Troubleshooting Tips
79
Software Communication Problems
Problem
The frame is powered up, but the module does not communicate with CCS Navigator or the web GUI interface.
Solutions
Ensure you have specified the proper module slot.
See your 6800 + Frame Installation and Operation Manual for more information about slot identification.
Confirm there is an 6800 + ETH module installed in the frame.
Remove any legacy 6800 series product that is in the frame.
CCS software cannot communicate with legacy 6800 series products, even if these modules may operate with card-edge controls in the frame. Legacy 6800 products do not have the “ + ” symbol on their extractor handles.
Check for damaged pins on the back module by following this procedure: i.
Unplug the front module. ii.
Unscrew and remove the back module. iii.
Inspect the 20- or 30-pin spring connector at the bottom of the back module, and verify that the connector does not have any slightly bent, or severely depressed pins.
iv.
Carefully reposition any bent or depressed pins. If this is not possible, contact Harris
Customer Support.
Figure C-1 Typical Back Module Spring Connector
80 Appendix C
Communication and Control Troubleshooting Tips
Problem
The IP address of the frame has been forgotten.
Solution
Follow this procedure:
1 Remove the ETH6800 + module from the frame.
2 Select DIP switch 2 on the ETH6800 + module and slide the tab to the forward position.
This sets the ETH6800 + module to its default IP address of 192.168.100.250
.
Slide this DIP switch tab forward for default IP address
Figure C-2 ETH6800 + DIP Switch
3 Use CCS Navigator or the web browser to interface with the ETH6800 + module and then set the desired IP address.
4 Set the DIP switch back to its normal position and then re-insert the module.
Problem
There is no Ethernet connectivity with the frame.
Solutions
Verify that the correct IP address is being used. If your are not certain, refer to the above procedure to set to default IP.
Verify that the ethernet cable is the correct type (a crossover cable is required for direct connection from a PC).
Verify the Link and Activity (left and right) status LEDS are active on the RJ-45 connector at the rear of the frame.
Verify the Status LED is lit and green on the ETH6800+ card, as viewed from the front of the frame with the door open.
Verify that the security settings on the PC allow for connection to a frame (TCP port 80 and UDP ports 4000/4050 must be open).
Verify that the PC is configured for and can communicate on the desired subnet.
Verify that the frame reference signal has not been mistakenly connected to a
Communications port on the rear of the frame.
HMX6803
+
and OP
+
HMX
+
Installation and Operation Manual
81
Problem
CCS software sees the frame, but does not find all of the modules.
Solutions
Remove any legacy 6800 series products.
Plug your modules in before starting the discovery.
Start your discovery after the frame and all modules have fully powered up.
Refresh the CCS software and ensure that the installed modules are fully powered up first before discovery.
Problem
CCS Software does not respond after it is launched.
Solutions
Close any CCS software that is already launched.
Problem
CCS software shows a module in the Control window, but cannot control it.
Solution
Follow this procedure:
1 Set the module’s Local/Remote jumper to Remote.
2 Ensure the module name in the Control window matches the module type in the frame.
3 Gently push the module into its slot in the frame to ensure it is seated properly and powered up.
4 Verify that the Control window indicates the device is ready.
Hardware Communication Problems
Problem
After a power failure, the frames and PC do not communicate.
Solution
Follow this procedure:
1 Wait four minutes for the frames to recover from the power failure.
2 Close the CCS software, and then restart the PC.
3 Restart the software application.
82 Appendix C
Communication and Control Troubleshooting Tips
Problem
The module does not seem to work.
Solutions
Ensure the correct frame is powered up.
Verify that all appropriate rear connections are secure.
Gently push the module into its slot in the frame to ensure it is seated properly. Then verify the Status LED on the module is lit and green.
Ensure the back module does not have any slightly bent, or severely depressed pins.
F ollow this procedure: i.
Unplug the front module. ii.
Unscrew and remove the back module.
iii.
Carefully reposition any slightly bent, or severely depressed pins. If this is not possible, contact Customer Support.
Index
A
Acknowledge, alarm
ADS (ancillary data stripper)
ADS clean parameter
AES input specification
AES optional license
AFD alarm
detection and insertion
parameters
Alarms
module-specific
priority
Ancillary data
Append embedding
,
Audio
AES input specification
balanced inputs
bit manipulation
embedding errors
embedding mode
format
input rate
path
PCM/non-PCM
sampling frequency
test tone
unbalanced breakout cable
inputs
word length
,
Audio delay
Auto-detection of video standards
Available parameters
B
Back connector
,
,
installing
Balanced audio inputs
Bank selection
Black clip
Breakout cables
C
Card-edge controls
C-bit
CCS applications changing parameter settings
Changing parameters
Channel status bits
Channel word length
CJ1 jumper
Clean, ADS
Cleaning fiber optic connections
Clear, alarm
Compatible frames
Connections external
internal
Control LEDs
,
Control packet
Control parameters, changing using CCS applications
Controls, card-edge
Cross section of optical fiber
D
Default IP address
Default parameter settings
Defects in a fiber connection
Delay
Description, general
Discovering a module
Dry cleaning
E
Embed mode parameters
Embedder ancillary data
errors
mode
83
84 Index
Equalization
Error counter
External audio processing delay
F
Factory default settings
Features
Fiber optic specifications
Format, audio
FR6802+ frames
Frames, compatible
Front module
installation and removal
G
Gain parameters
Genlock
H
Hardware version
HD operating mode
,
features
specifications
Horizontal phase
I
Input video standard
Inputs
AES specification
audio rate
video specification
Inspecting and cleaning fiber connections
Installation
Invert parameter
IP address
J
Jumper CJ1 for local/remote control
L
Laser output specifications
Laser precautions
–
,
LEDs
control
module status
monitoring
License keys
adding
purchasing
Local control
jumper for setting
M
Manual information
Maximum allowable power ratings
Metadata parameters
Module status LEDs
,
Modules back
front
installation and removal
–
Monitoring LEDs
N
Navigation switch
Non-PCM audio
O
OP
+
HMX
+
specifications
Operating notes
Operating temperature
Optical output specifications
Optional licenses
features
Outputs audio channel source
laser specifications
test tone
video specifications
Overwrite embedding
P
Packing list
Parameter availability
Parameter settings, changing using CCS applications
Parameters changing using CCS applications
cross-functional changes
defaults
HD operating mode
remote control
SD operating mode
setting at card-edge
Path, audio
PCM audio
Phase, horizontal and vertical
Pinouts breakout cable
RS-422/RS-232
Power consumption specifications
maximum frame ratings
Priority, alarm
Product description
Product servicing
Propagation delay specifications
Q
Q-SEE compliant thumbnails
R
Recalling default parameter settings
Remote control
Removing a module
Required frames
Reset factory defaults
Returning a product
Revision history of the manual
RoHS compliance
Rotary switch
RS-422/RS-232
specifications
S
Safety precautions with lasers
–
standards and compliances
terms and symbols
Safety precautions
Sampling frequency
SD operating mode
specifications
Serial number
Shipping information
Signal flow
Software controlling module
Software version
Source select parameter
Specifications
fiber optic video output
laser output
Standards
RoHS compliance
WEEE compliance
Start-up time specification
HMX6803
+
and OP
+
HMX
+
Installation and Operation Manual
85
T
Temperature
Test pattern generator
Test tone frequencies
Thumbnails, Q-SEE compliant
Trigger, alarm
U
Unbalanced audio breakout cable
inputs
Unpacking information
Usable slots
User bits (U-bits)
V
Validity bits (V-bits)
Vertical phase
VI detection and insertion
parameters
Video delay bypass parameter
gain parameters
input specification
input standard
offset parameters
output specifications
proc amp enable
W
WEEE compliance
Wet cleaning
White clip
Word length
,
,
WSS detection and insertion
parameters
86 Index
Prenesi
Javna povezava posodobljena
Javna povezava do vašega klepeta je bila posodobljena. You may view and manage your chat links after registration here.
Javna povezava do dokumenta
Oglas
