Operating Manual & Parts List

9681121

Read carefully and follow all safety rules and operating instructions before first use of this product.

9644210.01-0519

Model #: ___________________

Serial #: ____________________

Purch. Date: ________________

GETTING STARTED

Structural Requirements

Make sure all supporting structures and load attaching devices are strong enough to hold your intended loads. If in doubt, consult a qualified structural engineer.

Electrical Requirements

The motor is designed for operation on the voltage and frequency specified. Normal loads will be handled safely on voltages not more than 10% above or below the specified voltage.

Running the unit on voltages which are not within the range may cause overheating and motor burn-out. Heavy loads require that the voltage at motor terminals be no less than the voltage specified.

Tools Needed

Standard mechanic’s hand tool set.

DESCRIPTION

NORSE Belt & Disc Sander/Grinder is used for grinding, deburring, squaring, polishing and finishing metals, woods and plastics. The

Belt & Disc Sander/Grinder has a totally enclosed, fan-cooled direct drive motor, fully adjustable tool rests and OSHA compliant safety guards. Belt housing swivels from vertical to horizontal for grinding long workpieces features and a quick release belt tension and tracking mechanism.

UNPACKING

Check for shipping damage. If damage has occurred, a claim must be filed with the carrier immediately. Check for completeness.

Immediately report missing parts to dealer.

If you suspect a belt or disc of being damaged, replace it immediately.

SAFETY RULES

For your own safety, read operating instructions manual before operating tool.

PROPOSITION 65 WARNING: Some dust created by using power tools contain chemicals known to the state of California to cause cancer, birth defects or other reproductive harm.

Some examples of these chemicals are:

• Lead from lead-based paints

• Crystalline silica from bricks and cement and other masonry products.

• Arsenic and chromium from chemically treated lumber.

Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals; work in a well ventilated area and work with approved safety equipment. Always wear OSHA/NIOSH approved, properly fitting face mask or respirator when using such tools

Be Prepared for Job

• Wear proper apparel. Do not wear loose clothing, gloves, neckties, rings, bracelets or other jewelry which may get caught in moving parts of machine.

• Wear protective hair covering to contain long hair.

• Wear safety shoes with non-slip soles.

• Wear safety glasses complying with United States ANSI Z87.1.

Everyday glasses have only impact resistant lenses. They are

NOT safety glasses.

• Wear face mask or dust mask if operation is dusty.

• Be alert and think clearly. Never operate power tools when tired, intoxicated or when taking medications that cause drowsiness.

Unpack

Do not discard packing materials until after machine has been inspected for damage and completeness. Locate loose parts and set aside. Refer to Assembly on page 3 for contents list.

Inspect

• After unpacking the unit, carefully inspect for any damage that may have occurred during transit. Check for loose, missing or damaged parts. Shipping damage claims must be filed with the carrier.

• All tools should be visually inspected before use, in addition to regular periodic maintenance inspections.

• Be sure that the voltage labeled on the unit matches your power supply.

Prepare Work Area for Job

• Keep work area clean. Cluttered work areas and work benches invite accidents.

• Do not use power tools in dangerous environments. Do not use power tools in damp or wet locations. Do not expose power tools to rain.

• Work area should be properly lighted.

• Proper electrical plug should be plugged directly into properly grounded, three-prong receptacle.

• Extension cords should have a grounding prong and the three wires of the extension cord should be of the correct gauge.

• Keep visitors at a safe distance from work area.

• Keep children out of the workplace. Make workshop childproof.

Use padlocks, master switches or remove switch keys to prevent any unintentional use of power tools.

1

SAFETY RULES (CONTINUED)

Tool Should Be Maintained

• Always unplug tool prior to inspection.

• Consult manual for specific maintaining and adjusting procedures.

• Keep tool clean for safest operation.

• Remove adjusting tools. Form habit of checking to see that adjusting tools are removed before turning machine on.

• Keep all parts in working order. Check to determine that the guard or other parts will operate properly and perform their intended function.

• Check for damaged parts. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting and any other condition that may affect a tool’s operation.

• Replace worn or damaged cord immediately.

• A guard or other part that is damaged should be properly repaired or replaced. Do not perform makeshift repairs. (Use the parts list to order replacement parts.)

• Maintain tools with care. Keep tools sharp and clean for best and safest performance. Follow instructions for lubricating and changing accessories.

Know How to Use Tool

• Use right tool for job. Do not force tool or attachment to do a job for which it was not designed.

• Disconnect tool from power when changing accessories such as grinding wheels, buffing wheels and the like.

• Avoid accidental start-up. Make sure that the switch is in the off position before plugging in.

• Do not force tool. It will work most efficiently at the rate for which it was designed.

• Keep hands away from moving parts and grinding surfaces.

• Never leave a tool running unattended. Turn the power off and do not leave tool until it comes to a complete stop.

• Do not overreach. Keep proper footing and balance.

• Never stand on tool. Serious injury could occur if tool is tipped over.

• Know your tool. Learn the tool’s operation, application and specific limitations.

• Use recommended accessories. Understand and obey all safety instructions supplied with accessories. The use of improper accessories may cause risk of injury to persons.

• Turn machine off if it jams. Belt or disc jams when it digs too deeply into workpiece. (Motor force keeps it stuck in the work.)

• Maintain 1/16˝ maximum clearance between tool rest and abrasive belt/disc.

• Handle the workpiece correctly. Whenever possible, use tool rest to support workpiece during grinding operation. Turn tool off if it jams.

2

• Make sure the tool is secured to a steady, flat working surface.

When used with a stand, make sure the stand is bolted to a flat surface to prevent tipping over.

• Support workpiece with tool rest.

• Clean sanding dust from beneath tool frequently.

SPECIFICATIONS

Belt Size

Belt Platen Area

Belt Drum Dimensions

Belt Table Dimensions

Belt Table Tilts

Belt Dust Chute Diameter

Belt Speed

Disc Diameter

Disc Table Dimensions

Disc Table Tilts

Disc Dust Chute Diameter

Disc Speed

Base Dimensions

Switch

Motor

Weight

Shipping Weight

49G990B

6 × 48˝

7 1 ⁄

8

× 17˝

3 × 6 1 ⁄

8

˝

5 7 ⁄

8

× 9 13 ⁄

16

˝

0 To 60º

2˝

2700 SFPM

9˝

5 7 ⁄

8

× 11 13 ⁄

16

˝

0 to 45º

1 1 ⁄

4

˝

3450 RPM

14 1 ⁄

2

× 14 1 ⁄

2

˝

SP, Locking rocker

1 HP, 120/240 V, 9/4.5 Amps

100 lbs

110 lbs

ASSEMBLY

Refer to Figures 1, 2 and 6, page 10.

Do not attempt to operate tool until it is completely assembled according to instructions.

Do not attempt assembly if parts are missing. Use this manual to order repair parts.

Assemble Stand

Refer to Figure 1.

NOTE: Finger tighten bolts and nuts until assembly is complete.

Then tighten all fasteners securely.

1. Install foot by pressing onto all four legs.

2. Attach one top frame to one pair of legs using carriage bolts, flat washers and hex nuts. Repeat for second pair of legs.

3. Attach one brace to each pair of legs using carriage bolts, flat washers and hex nuts.)

4. Connect the two leg sets with the two remaining top frames.

Make sure that the square holes in the legs align with the square holes in the top frame. Also make sure that the slots on top of the frame members are aligned at each corner. Secure frames to legs using carriage bolts, flat washers and hex nuts.

5. Attach the two remaining braces by aligning the square holes in the legs and the braces. Insert carriage bolts, flat washers and secure with hex nuts.

Top Frame

Assemble Disc Table

Refer to Figure 2.

1. Attach disc guard to end shield using three pan head screws, three flat washers and three lock washers.

2. Remove tape from key and armature. Slide aluminum disc with abrasive disc onto armature with keyway in disc aligned with key in armature. Secure disc to armature using set screw.

3. Slide disc dust chute onto disc guard from below the 9˝ disc with exhaust port to rear of tool. Secure dust chute to disc guard with two pan head screws.

4. Slide disc table with attached trunnions onto the raised bosses on each side of disc guard. Mount two handles and flat washers through trunnions into threaded holes on each side of disc guard.

5. Locate table in desired position and secure with handles.

6. Be sure the gap between the disc and disc table is 1/16˝ or less.

7. If adjustment is necessary, loosen set screw in aluminum disc through the opening at top-rear of disc guard. Position disc

1/16˝ or less from edge of table. Secure disc with set screw.

End Shield

Armature and Key

Disc Guard

Set Screw

Aluminum Disc with Abrasive

Disc

Carriage

Bolt

Hex

Nut

Flat

Washer Brace

Leg

Foot

Figure 1 - Assemble stand.

Mount Sander to Stand

1. Place sander on the stand.

2. Align mounting holes of sander with slots on top frame.

3. Secure sander to stand on all four corners using four 5/16-18 x

2˝ hex head bolts, eight 5/16˝ flat washers and four 5/16-18 hex nuts.

Trunnion

Disc Table

Flat Washers

Figure 2 – Assemble disc table.

Handle

Dust Chute

Assemble Belt Table

Refer to Figure 6, page 10.

Slide belt table assembly (Ref. No. 76) into trunnion groove of pivot bracket (Ref. No. 47). Mount using socket head bolt and flat washer (Ref. Nos. 2 and 75). Locate table in desired position. Be sure that gap between belt table and belt is 1/16˝ or less. Tighten bolt securely.

3

INSTALLATION

Refer to Figures 3, 4 and 5.

All electrical connections must be performed by a qualified electrician.

Power Source

The motor is designed for operation on the voltage and frequency specified. Normal loads will be handled safely on voltages not more than 10% above or below the specified voltage.

Running the unit on voltages which are not within the range may cause overheating and motor burnout. Heavy loads require that voltage at motor terminals be no less than the voltage specified on nameplate. Power supply to the motor is controlled by a single pole locking rocker switch. Remove the key to prevent unauthorized use.

Grounding Instructions

Improper connection of equipment grounding conductor can result in the risk of electrical shock. Equipment should be grounded while in use to protect operator from electrical shock.

• Check with a qualified electrician if grounding instructions are not understood or if in doubt as to whether the tool is properly grounded.

• This tool is equipped with an approved 3-conductor cord rated at 300V and a 3-prong grounding type plug (See Figure 3) for your protection against shock hazards.

• Grounding plug should be plugged directly into a properly installed and grounded 3-prong grounding-type receptacle, as shown (Figure 3).

Properly grounded outlet

Grounding prong

3-Prong plug

Figure 3 – 3-Prong receptacle.

• Do not remove or alter grounding prong in any manner. In the event of a malfunction or breakdown, grounding provides a path of least resistance for electrical shock.

Do not permit fingers to touch the terminals of plug when installing or removing from outlet.

• Plug must be plugged into matching outlet that is properly installed and grounded in accordance with all local codes and ordinances. Do not modify plug provided. If it will not fit in outlet, have proper outlet installed by a qualified electrician.

• Inspect tool cords periodically, and if damaged, have repaired by an authorized service facility.

• Green (or green and yellow) conductor in cord is the grounding wire. If repair or replacement of the electric cord or plug is necessary, do not connect the green (or green and yellow) wire to a live terminal.

• Where a 2-prong wall receptacle is encountered, it must be replaced with a properly grounded 3-prong receptacle installed in accordance with National Electric Code and local codes and ordinances.

This work should be performed by a qualified electrician.

• A temporary 3-prong to 2-prong grounding adapter (See Figure

4) is available for connecting plugs to a two pole outlet if it is properly grounded.

Grounding lug

Adapter

Make sure this is connected to a known grounded receptacle

3-Prong plug

2-Prong receptacle

Figure 4 – 2-Prong receptacle with adapter.

• Do not use a 3-prong to 2-prong grounding adapter unless permitted by local and national codes and ordinances.

(A 3-prong to 2-prong grounding adapter is not permitted in

Canada.) Where permitted, the rigid green tab or terminal on the side of the adapter must be securely connected to a permanent electrical ground such as a properly grounded water pipe, a properly grounded outlet box or a properly grounded wire system.

• Many cover plate screws, water pipes and outlet boxes are not properly grounded. To ensure proper ground, grounding means must be tested by a qualified electrician.

Extension Cords

Use proper extension cord. Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. Table shows the correct size to use depending on cord length and nameplate ampere rating. If in doubt, use the next heavier gage. The smaller the gage number, the heavier the cord.

Ampere Rating

More

0

6

10

12

Not

6

10

12

16

Extension Cord Table

Volts

120

240

Total Length of Cord in Feet

18

18

16

14

25 50 100 150

50 100 150 300

Minimum Gage for Cord

16 16 14

16 14 12

16 14 12

12 Not Recommended

4

INSTALLATION (CONTINUED)

Electrical Connections

All electrical connections must be performed by a qualified electrician. Make sure tool is off and disconnected from power source while motor is mounted, connected, reconnected or anytime wiring is inspected.

• Motor and wires are installed as shown in wiring diagram (See

Figure 5). Motor is assembled with approved, 3-conductor cord to be used at 120/240 volts. Motor is prewired at the factory for

120 volts.

• To use the grinder with a 240V power supply, have a qualified electrician rewire motor and attach a 240 volt, 15A three-prong plug onto grinder line cord.

Blue Red White Brown Blue Red White Brown

• For optimum performance do not stall motor or reduce speed.

Do not force the work into the abrasive.

• Support workpiece with tool rest when grinding with belt/disc.

• Never push a sharp corner of workpiece rapidly against belt/disc. Abrasive backing may tear.

• Replace abrasives when they become loaded (glazed) or frayed.

• When grinding metal, move workpiece across abrasive to prevent heat build-up.

• Never attempt wet sanding. If work-piece becomes too hot to handle, cool it in water.

• Do not expose to rain or use in damp locations.

120V

Figure 5 – Wiring diagram.

240V

OPERATION

Operation of any power tool can result in foreign objects being thrown into eyes which can result in severe eye damage. Always wear safety goggles complying with United States ANSI Z87.1 (shown on package) before commencing power tool operation.

Always observe the following safety precautions:

• Whenever adjusting or replacing any parts on the sander turn power off and remove the plug from power source.

• Recheck tool rest bolts, they must be tightened securely.

• Make sure all guards are properly attached. All guards should be securely fastened.

• Make sure all moving parts are free and clear of any interference.

• Make sure all fasteners are tight and have not vibrated loose.

• With power disconnected, test operation by hand for clearance and adjust if necessary.

• Always wear eye protection or face shield.

• Make sure abrasive belt tracks properly. Correct tracking gives optimum performance.

• After turning switch on, always allow belt and disc to come up to full speed before sanding or grinding.

• Abrasive belt must travel towards tool rest.

• Avoid kickback by grinding in accordance with the directional arrows.

• Keep your hands clear of abrasive belt/disc and all moving parts.

Replacing Abrasive Belt

Refer to Figure 6, page 10.

Abrasive belt should be replaced when worn, torn, or glazed.

Loosen belt cover knobs (Ref. No. 18) and open belt cover.

1. Release belt tension by pushing tension lever (Ref. No. 35) towards idler drum. Slide old belt off the idler and drive wheels.

NOTE: There may be an arrow on the inside of the belt. The arrow should point down toward the belt table to ensure that the splice in the belt will not come apart.

2. Slide new belt over the drive and idler drums; center belt on drums.

3. Push tension lever towards drive drum to tension belt.

4. Rotate belt by hand to check tracking. Belt should ride centered on drive and idler drums. Adjust thumb nut (Ref. No.

29) as needed to center belt on drums. When belt tracks properly, tighten hex nut. (Ref. No. 28) If adjustment of thumb nut does not provide desirable tracking, adjust the stud (Ref.

No. 30) using a flat screwdriver. To adjust stud, loosen hex nut and turn stud counterclockwise to move belt to the right or clockwise to move belt to the left until belt rides centered on drive and idler drums. Tighten hex nut while holding the stud in place.

5. Close belt cover and tighten knobs.

Adjust Belt Assembly Position

Refer to Figure 6, page 10.

Sanding belt assembly can be adjusted from horizontal to vertical position.

1. Loosen socket head bolt (Ref. No. 37 is threaded into pivot bracket.

2. Tilt belt assembly to desired position (from horizontal to vertical). Secure belt assembly position by tightening socket head bolt in pivot bracket.

5

OPERATION (CONTINUED)

Adjust Belt Table

Refer to Figure 6, page 10.

1. To adjust belt table angle, loosen socket head bolt (Ref. No.

75).

2. Tilt belt table to desired position. Adjust for 1/16˝ maximum clearance between the belt and the table. Secure by tightening socket head bolt.

Replacing Abrasive Disc

Refer to Figure 6, page 10.

1. Remove disc table and dust chute (Ref. Nos. 4 and 8).

Remove old abrasive disc by peeling it from the aluminum disc.

Removing aluminum disc from motor shaft is not necessary.

2. Clean aluminum disc if necessary. Select the proper abrasive disc and apply to aluminum disc.

3. Replace dust chute and disc table.

Horizontal Belt Sanding

Refer to Figure 6, page 10.

The belt platen can be tilted from a vertical to a horizontal position.

1. Remove the belt table by removing the socket head bolt and flat washer (Ref. Nos. 2 and 75). Loosen the socket head bolt

(Ref. No. 37) in the pivot bracket; tilt the belt platen assembly to the horizontal position and tighten the socket head bolt to secure position.

Adjusting Disc Table Angle

Refer to Figure 6, page 10.

Disc table is adjustable from 0 to 45º for beveled work.

1. To adjust the disc table, loosen the two handles (Ref. No. 1) and pivot to the desired angle.

2. Use the scale on disc table trunnions to set table from 0 to 45º from abrasive disc.

3. When disc table is at desired angle, lock it into position by securely tightening the handles.

Work Stop

Refer to Figure 6, page 10.

The work stop (Ref. No. 74) can be used instead of the belt table.

1. Remove socket head bolt and flat washer (Ref. Nos. 2 and 75) holding belt table on pivot bracket. Remove belt table.

2. Mount work stop to pivot bracket using the socket head bolt and washer.

Abrasive Disc Finishing

Excessive force on the disc will shorten the life of the disc and the motor.

• Abrasive disc sanding is well suited for finishing small flat surfaces and convex edges.

• Move workpiece across down side (right) of abrasive disc.

• Abrasive disc moves fastest and removes more material at outer edge.

• For accuracy, use miter gauge.

Abrasive Belt Finishing

Excessive force on the belt will shorten the life of the belt and the motor.

• Finishing flat surfaces: Hold workpiece firmly with both hands; keep fingers away from abrasive belt.

Use work stop. Work stop is used to position and secure work being sanded. Keep end butted against work stop and move work evenly across abrasive belt. Use extra caution when finishing very thin pieces.

Finishing long pieces: remove work stop. Apply only enough pressure to allow abrasive belt to remove material.

• Finishing curved edges: Finish outside curves on flat portion of abrasive belt. Finish inside curves on idler drum portion of abrasive belt.

• Finishing end grain: It is more convenient to finish ends of long workpieces with the abrasive belt in a vertical position.

Position table on belt side of sander. Lock into position with socket head bolt and washer. Move work evenly across abrasive belt. For accuracy, use miter gauge. Table may be tilted for beveled work.

Using Miter Gauge

• The miter gauge is used on both belt and disc tables. Use the miter gauge for securing the work and holding the proper angle while sanding.

• Adjust angle by repositioning the miter gauge scale and locking it into place with knob.

• Check accuracy of miter gauge scale.

• Use a combination square to adjust miter gauge square to disc. Indicator should be at zero. Loosen screw and reposition indicator if necessary.

6

MAINTENANCE

Make certain that the unit is disconnected from power source before attempting to service or remove any component.

Cleaning

• Keep machine and workshop clean. Do not allow sawdust to accumulate on the tool.

• Keep the drums clean. Dirt on drums will cause poor tracking and belt slippage.

• Operate tool with dust collector to keep dust from accumulating.

After sanding wood or non-metallic material, always clean dust collector and guards of sawdust before grinding metal. Sparks could ignite debris and cause a fire.

• Be certain motor is kept clean and is frequently vacuumed free of dust.

• Use soap and water to clean painted parts, rubber parts and plastic guards.

Lubrication

• The shielded ball bearings in this tool are permanently lubricated at the factory. They require no further lubrication.

• When operation seems stiff, a light coat of paste wax applied to the belt table and disc table will make it easier to feed the work while finishing.

• Do not apply wax to the belt platen. Belt could pick up wax and deposit it on wheels causing belt to slip.

Keep Tool In Repair

• If power cord is worn, cut or damaged, have it replaced immediately.

• Replace worn abrasives when needed.

• Replace any damaged or missing parts. Use parts list to order parts.

• Any attempt to repair motor may create a hazard unless repair is done by a qualified service technician.

7

8

TROUBLESHOOTING GUIDE

Symptom

Motor will not start.

Possible Cause(s)

1. Blown line fuse or tripped circuit breaker.

2. Low line voltage.

Motor will not start; fuses blown or circuit breakers tripped.

3. Defective switch.

4. Defective, blown capacitor.

1. Overloading due to binding.

2. Defective plug.

3. Defective cord.

4. Defective switch.

5. Motor wired for different line voltage.

Motor fails to develop full power

(power output of motor decreases rapidly with decrease in voltage at motor terminals).

Motor overheats

Motor stalls

(resulting in blown fuses or tripped circuit breakers).

6. Faulty internal wiring.

1. Power line overloaded with lights, appliances and other motors.

2. Undersized wires or circuits too long.

3. General overloading of power company’s facilities.

Motor overloaded

1. Short circuit in motor or loose connections.

Machine slows down while operating.

Abrasive belt runs off top wheel.

2. Low voltage.

3. Motor wired for different line voltage.

4. Incorrect fuses or circuit breakers in power line.

5. Motor overloaded.

Applying too much pressure to workpiece.

Not tracking properly.

Corrective Action

1. If fuse is blown, replace with fuse of proper size. If breaker tripped, reset it.

2. Check power supply for voltage and correct as needed.

3. Replace switch.

4. Replace capacitor.

1. Clean around wheels and shaft and/or replace bearings.

2. Replace plug.

3. Replace cord.

4. Replace switch.

5. Rewire motors as per line voltage (See

Electrical Connections, page 5).

6. Have a qualified electrician service unit.

1. Reduce load on power line.

2. Increase wire sizes, or reduce length of wiring.

3. Request a voltage check from power company.

Reduce load on motor.

1. Inspect connections in motor for loose or shorted terminals or worn insulation on lead wires.

2. Correct the low line voltage conditions.

3. Rewire motor as per line voltage.

4. Install correct fuses or circuit breakers (See

Electrical Connections, page 5).

5. Reduce load on motor.

Ease up on pressure.

See Operation section “Tracking abrasive belt”.

NOTES

9

10

11

REPAIR PARTS ILLUSTRATION FOR STAND

1

7

6

8

9

5

4

3

2

Figure 7 – Replacement parts illustration for stand.

12

REPAIR PARTS LIST FOR STAND

Ref.

No.

7

8

5

6

9

3

4

1

2

Description

Top Frame

Brace

Leg

Foot

Carriage bolt M6 ×12

Flat washer M8

Hex Nut M8

Hex head bolt M8 ×55

Flange Nut M6

(∆) Not shown.

(▲) Not included.

(N/A) Not available as replacement part.

(*) Standard hardware item, available locally.

Part

Number

*

*

*

*

*

9636351.00

9636352.00

9636353.00

9636354.00

Qty.

4

4

32

8

32

4

4

4

4

13

NORSE Operating Manual & Parts List 9681121

NORSE WARRANTY

NORSE by C.H. Hanson warrants their products to be free of defects in material or workmanship. This warranty does not cover defects due directly or indirectly to misuse, abuse, normal wear and tear, failure to properly maintain the product, heated, ground or otherwise altered, or used for a purpose other than that for which it was intended.

The warranty does not cover expendable and/or wear part (i.e. v-belts, screws, abrasives, jaws), damage to tools arising from alteration, abuse or use other than their intended purpose, packing and freight. The duration of this warranty is expressly limited to the terms noted below beginning from the date of delivery to the original user.

The NORSE branded items carry the following warranties on parts:

All NORSE branded Tools and Accessories 1 YEAR

The obligation of NORSE by C.H. Hanson is limited solely to the repair or replacement, at our option, at its factory or authorized repair agent of any part that should prove inoperable. Purchaser must lubricate and maintain the product under normal operating conditions at all times. Prior to operation become familiar with product and the included materials, i.e. warnings, cautions and manuals.

Failure to follow these instructions will void the warranty.

This warranty is the purchaser's exclusive remedy against C. H. Hanson for any inoperable parts in its product. Under no circumstances is C. H. Hanson liable for any direct, indirect, incidental , special or consequential damages including loss of profits in any way related to the use or inability to use our products. This warranty gives you specific legal rights which may vary from state to state.

SERVICE & REPAIR

1. If a NORSE product requires a repair or warranty service DO NOT return the product to the place of purchase.

2. All warranty related work must be evaluated and approved by NORSE.

3. Prior to returning any item the user must obtain factory approval and a valid RGA number.

4. For instructions and RGA number call toll free (800) 827-3398.

NORSE - a C.H. Hanson brand

2000 N. Aurora Rd., Naperville, IL 60563 U.S.A.

or call: 1-800-827-3398

18-0307