LADEN C 445 BL Dishwasher Program Chart

C 445

Before using the dishwasher, read the user instructions!

Quick Reference Guide

GB

Start button

Switches “on” when the dishwasher is operating. Flashes when a fault occurs.

Switches off at the end of the programme.

Indicators

Add regeneration salt

Only add regeneration salt immediately before starting a wash programme.

Program selector knob

On / Off button

Programmes

Programme chart

Loading instructions

Pre-Rinse cold

Crockery to be washed later.

Rapid 40°C

Lightly soiled crockery with no dried-on food.

Detergent

2)

A

Consumption

3)

B Litres kWh Minutes

5.0

0.02

10

X 13.0

0.70

30

Normal

1)

50°C

Normally or heavily soiled crockery.

X X 16.0

1.05

130

Intensive 70°C

Recommended programme for heavily soiled crockery, especially suitable for pans and saucepans.

X X 17.0

1.90

125

1) Reference programme for energy label in compliance with

EN 50242 regulations;

2) Refer to “User instructions”;

3) Program data obtained in conformity with European standard EN 50242. Values may vary in relation to usage, e.g.: different loads, water temperatures - above or below

15°C - as well as water hardness and power supply voltage, etc.

Important information for Test Laboratories:

For detailed information on the EN comparison test and other tests, contact the following address:

“[email protected]”.

5019 696 93146

(We reserve the right to make technical modifications)

LA/I/B/GB

How to use the appliance

Further indications are given in the single chapters and in the user instructions.

Switch on the appliance

Press the ON/OFF button.

How to fill the detergent

Check the rinse aid level

Large compartment A:

With each wash cycle.

Small compartment B:

For programmes with pre-wash only.

Mechanical indicator C.

Electric indicator on control panel (if provided).

A B C

Check the regeneration salt level

On models with water softener system only.

Mechanical indicator D. Electric indicator on control panel (if provided).

Load the racks

Close the dishwasher door,

turn on the water tap

Refer to the dishwasher loading instructions.

Select a programme

The last programme selected will light up.

Select the desired programme (using the specific button or knob).

The corresponding indicator lamp lights up.

Select options

If necessary (and if provided) the corresponding indicator lamp lights up.

Press the Start button

Switch off the appliance

The selected programme is then memorised (even in the event of power failure).

“Change programme”

Press the START button for 2 sec. until the Start indicator lamp switches off;

Select another programme and press the START button again.

- Only open the dishwasher if necessary

(Warning: beware of hot steam).

- If the appliance is switched off during a wash cycle, when switched on again it will resume the cycle from where it was interrupted.

Only after the START button has switched off: Press the ON/OFF button.

All the indicator lamps switch off.

Turn off the water tap, unload the racks

Warning: when the door is opened steam comes out!

Unload the appliance, starting from the lower rack.

LA/II/B/GB

Dishwasher loading instructions and racks provided

Upper rack:

Fold down glass holder (A):

Depending on the position, for example small or long-stemmed glasses.

Crockery holders (B):

Depending on the position, for example plates, cups and long-stemmed glasses.

Rack height adjustment (also when loaded):

Lower adjustment:

Upper adjustment:

Pull the two rack handles

(C) outwards and lower the rack.

Pull the two rack handles

(C) upwards until the rack clicks into place (factory setting).

The rack must be level on both sides.

Lower rack:

Plate holders (D).

Cutlery basket (E)

A grid (F) can be fitted onto the cutlery basket to keep items separated.

Sharp knives and forks that might cause injury must be placed in the cutlery basket with the handles positioned upwards.

Only use dishwasher-proof crockery and dishes. Do not use the appliance for items not suitable for washing in a dishwasher, for example wooden items, aluminium, plastic utensils, tin, hand-decorated crockery (unglazed), silver cutlery.

LA/III/GB

What to do if...

If a fault occurs, before contacting our After-Sales Service, make the following checks to try and remedy the problem

(* see also the corresponding chapter in the user instructions).

Problem Cause Remedy

The appliance is not working

• No water supply.

• Open the tap.

• The appliance does not load sufficient water.

• There is a power failure.

• Starting the selected programme.

• Insufficient rinse aid.

• Clean the water supply tap filter.

• Ensure there are no kinks in the water hose.

• Insert the plug into the mains socket.

• Press the Start button.

• Close the door.

• Check the domestic circuit fuse.

• The programme can be set to “0” to start.

• Increase dosage *.

If crockery is not perfectly dry

If crockery is not perfectly clean

Sandy or grainy residues

Colour of plastic parts faded

• Residual water in cavities.

• Load crockery at an angle.

• The water jet does not reach the crockery.

• Arrange crockery so that items do not touch each other. Load crockery upside down.

• Insufficient detergent.

• Unsuitable programme.

• Spray arms blocked.

• Spray arm nozzles clogged.

• Follow recommended detergent dosage.

• Select a more intense wash cycle.

• The spray arms must be able to turn freely.

• Remove any impurities obstructing the water flow *.

• Incorrect detergent/detergent too old. • Use a good quality detergent.

• Clogged filters.

• Filters incorrectly assembled.

• Tomato/carrot juice,...

• Check filters regularly/if necessary clean *.

• Insert the filter correctly *.

• Depending on the material, if necessary use a detergent with a greater whitening power.

Deposits on crockery

• removable

• not removable

• Streaks on the crockery/glasses.

• Streaks on glasses.

• Layer of salt on crockery/glasses.

• Insufficient water softening, calcium deposits.

• Increase the rinse aid dosage *.

• Reduce the rinse aid dosage *.

• Close the salt container lid properly *.

• Change water hardness setting, if necessary add salt *.

• Cannot be washed in the dishwasher.

• Use suitable glasses.

Opaque glasses/ glasses not sparkling

Rust on cutlery • Not made of stainless steel.

• Use suitable cutlery.

Identifying appliance faults

• The START indicator lamp flashes.

• Indicator F... (if provided).

• Ensure that the filter assembly is not clogged and if necessary clean it *.

Start the programme again. Press the Start button for

2 seconds, until the Start indicator lamp switches off.

Select a new programme and press the Start button again.

• Call the After-Sales Service.

If after carrying out the above checks the malfunction persists or appears again, turn the appliance off and turn off the water supply tap, then call our After-Sales Service (see guarantee).

Before contacting our After-Sales Service, take note of the following:

• The nature of the fault.

• The appliance type and model.

• The service code (the number indicated on the adhesive rating plate) inside the door on the right-hand side.

LA/IV/GB