Oki PT390 Parallel POS Printer User's Guide
Advertisement
Advertisement
PT390
Windows Driver User’s Guide
Windows Driver User's Guide 1.0.1.1
Table of Contents
Copyright (C) 2012 Oki Data Corporation 1 of 56
Windows Driver User's Guide 1.0.1.1
1 Introduction
1.1 Overview
This document describes how to use the Windows printer driver for the PT390 printer.
The PT390 Windows printer driver is a software program for printing documents from Windows applications to the PT390 printer. It converts printing data from applications into the format required by the PT390 and sends it to the printer. You can also set various printing functions such as bar codes, paper saving, print position alignment, and paper cutting.
1.2 Trademarks
All company names and product names contained in this manual are registered trademarks or trademarks of their respective owners.
This printer driver can be used with the following system configurations.
Printer Setup
Error : Auto Recovery
Cover Open Error: Auto Recovery
<Guide> The above settings are the factory defaults.
Usually, you do not have to modify the setting. However, the OPOS driver uses
"Recovery by Command" as the [Error] setting and therefore you need to change the default value in this case.
For information on how to set the value, please see the printer User's Guide.
Host Hardware
A personal computer with the following interfaces running one of the listed operating systems
(OS).
Serial
Parallel compatible with Centronics
USB
LAN
<Guide> LAN Interface
When using the driver on a LAN, install the "PR-PortManager", printing client software.
For information on how to install and use "PR-PortManager", please see the ”Installation
Guide”.
Copyright (C) 2012 Oki Data Corporation 2 of 56
Windows Driver User's Guide 1.0.1.1
Operating System (OS)
Microsoft® Windows® 2000
Microsoft® Windows® XP Professional
Microsoft® Windows® XP Home Edition
Microsoft® Windows Vista® Enterprise
Microsoft® Windows Vista® Business
Microsoft® Windows Vista® Ultimate
Microsoft® Windows Vista® Home Premium
Microsoft® Windows Vista® Home Basic
Microsoft® Windows® 7 Ultimate
Microsoft® Windows® 7 Enterprise
Microsoft® Windows® 7 Professional
Microsoft® Windows® 7 Home Premium
Microsoft® Windows® 7 Starter
Microsoft® Windows Server® 2003, Enterprise Edition
Microsoft® Windows Server® 2003, Standard Edition
Microsoft® Windows Server® 2008, Enterprise Edition
Microsoft® Windows Server® 2008, Standard Edition
Microsoft® Windows Server® 2008 R2, Enterprise Edition
Microsoft® Windows Server® 2008 R2, Standard Edition
Microsoft® Windows® Embedded for Point of Service
Microsoft® Windows® Embedded POSReady 2009
<Guide> The 64-bit OS versions are also supported.
In this document, each of the products is abbreviated as follows:
*1 : Windows 2000
*2 : Windows XP
*3 : Windows Vista
*4 : Windows 7
*5 : Windows Server 2003
*6 : Windows Server 2008
*7 : Windows Server 2008 R2
*8 : WEPOS
*9 : WEPOS 2009
(*5)
(*6)
(*6)
(*7)
(*7)
(*4)
(*4)
(*4)
(*4)
(*5)
(*8)
(*9)
(*1)
(*2)
(*2)
(*3)
(*3)
(*3)
(*3)
(*3)
(*4)
Copyright (C) 2012 Oki Data Corporation 3 of 56
Windows Driver User's Guide 1.0.1.1
2 Installing and Uninstalling the Driver
For information on how to install or uninstall this printer driver, please see the following topics:
"3. Installation" in the "Installation Guide"
"5. Uninstallation" in the "Installation Guide"
Copyright (C) 2012 Oki Data Corporation 4 of 56
Windows Driver User's Guide 1.0.1.1
3 How to Use the Printer Driver
This section describes how to setup the printer driver and the typical printing methods for printing documents from Windows applications to the PT390 printer.
After the printer driver is installed, printing a document from an application is performed as follows:
Ⅰ Install the printer driver
Ⅱ Set the port
If using with serial interface, configure the settings for the serial interface on the [Ports] tab of the
[Printer Properties].
[See Also]
3.1.1 How to Display the Printer Properties
3.2.1 Setting Port (for Serial Interface)
Ⅲ Set the custom paper type
While this printer driver provides four standard paper sizes, you can also create and register new paper sizes for the printer driver using the [Custom Paper] tab of [Printer Properties].
[See Also]
3.1.1 How to Display the Printer Properties
3.2.2 Setting Custom Paper
Ⅳ Print from application
Configure the print setup for the printer driver and print the document created in the application with the printer.
[See Also]
3.1.2 How to Display the Printing Preferences (Document Properties)
3.3 Printing from an Application
<Typical Printing Method>
3.4 Printing Bar Codes and 2D Codes
Copyright (C) 2012 Oki Data Corporation 5 of 56
Windows Driver User's Guide 1.0.1.1
3.1 How to Display the Setting Screen
There are two types of setting screens for the printer driver:
Printer Properties
In the [Printer Properties] screen, you configure the initial settings required for the printer driver to print documents, such as the custom paper and port (serial interface, for example) settings.
Printing Preferences (Document Properties)
In the Printing Preferences screen, you configure various printing features of the printer driver (for example, bar code or paper cut).
The following section explains how to display each of the screens.
Please note that the actual menu names may vary depending on the Windows screen settings.
Copyright (C) 2012 Oki Data Corporation 6 of 56
Windows Driver User's Guide 1.0.1.1
3.1.1 How to Display the Printer Properties
Administrative privileges are required to change the printer properties. Log on with an Administrator account to change the settings.
(1) Open the Printer folder.
・
From Windows' [Start] menu, select [Settings] → [Printers].
・
For Windows XP Professional
From Windows' [Start] menu, select [Printers and Faxes].
・
For Windows XP Home Edition
From Windows' [Start] menu, select [Control Panel] → [Printers and Other Hardware], and on the [Printers and Other Hardware] screen, select [View installed printers or fax printers].
・
For Windows Server 2003
From Windows' [Start] menu, select [Printers and Faxes].
・
For Windows Vista
From Windows' [Start] menu , select [Control Panel], and on the [Hardware and Sound] screen, select [Printers].
・
For Windows Server 2008
From Windows' [Start] menu, select [Control Panel] → [Printers].
For Windows 7
From Windows' [Start] menu , select [Devices and Printers].
For Windows Server 2008 R2
From Windows' [Start] menu, select [Devices and Printers].
Copyright (C) 2012 Oki Data Corporation 7 of 56
Windows Driver User's Guide 1.0.1.1
(2) Right-click “PT390 Raster” and select [Properties].
* For Windows Vista and Server 2008, if [Run as administrator] is displayed when you right-click a printer name, select [Run as administrator] → [Properties].
If the [User Account Control] dialog is displayed, select [Continue].
* For Windows 7 and Server 2008 R2, right-click the printer name and select [Printer Properties].
(3) The properties screen is displayed for the selected printer.
Copyright (C) 2012 Oki Data Corporation 8 of 56
Windows Driver User's Guide 1.0.1.1
3.1.2 How to Display the Printing Preferences (Document
Properties)
(1) Open the Printer folder.
See 3.1.1(1) for instructions on how to open the Printer folder.
(2) Right-click “PT390 Raster” and select [Printing Preferences].
(3) The Printing Preferences screen is displayed for the selected printer.
The values specified in the printer folder (shown above) are used as the initial values when printing from an application. You can also set the values for each job from within the application. For information on how to set the values in the application, please see "3.3 Printing from an Application".
Copyright (C) 2012 Oki Data Corporation 9 of 56
Windows Driver User's Guide 1.0.1.1
Setup the following items before using the printer driver to print documents. The initial values are specified in the printer properties screen.
Set Port (for Serial Interface)
Set Custom Paper
The settings are as follows.
3.2.1 Port Setting (for Serial Interface)
If this printer driver is used with the serial interface, set the port as follows:
Bits per second : 115200
Data bits
Parity
Stop bits
Flow control
: 8
:
None
: 1
: Hardware
The procedure is as follows.
(1) Open the Printer folder.
See 3.1.1(1) for instructions on how to open the Printer folder.
(2) Right-click “PT390 Raster” and select [Properties].
* For Windows Vista and Server 2008, if [Run as administrator] is displayed when you right-click a printer name, select [Run as administrator] → [Properties].
If the [User Account Control] dialog is displayed, select [Continue].
* For Windows 7 and Server 2008 R2, right-click a printer name and select [Printer Properties].
(3) Click the [Ports] tab and select the connected port (COMx:).
* "x" of "COMx:" indicates the port number.
(4) Click the [Configure Port] button.
(5) In the [COMx Properties] screen, set the bits per second, data bits, parity, stop bits, and flow control, and click the [OK] button.
(6) Click the [OK] button in the properties screen.
Copyright (C) 2012 Oki Data Corporation 10 of 56
Windows Driver User's Guide 1.0.1.1
3.2.2 Setting Custom Paper
This printer driver provides the following four standard paper sizes.
Paper Size
83 x 297 mm (53 column)
80 x 297 mm (48 column)
80 x 297 mm (42 column)
60 x 297 mm (36 column)
58 x 297 mm (35 column)
58 x 297 mm (32 column)
Left
1.0
4.0
8.0
3.0
3.0
5.0
Margin (mm)
Right Top
2.0
4.0
0.0
0.0
8.0
2.5
2.5
5.0
0.0
0.0
0.0
0.0
Bottom
0.0
0.0
0.0
0.0
0.0
0.0
If printing documents on different-sized paper, use the printer driver to define a custom paper size in advance. To specify a custom paper size, specify the printing paper size, assign a name, and register it with the printer driver. The following section describes how to setup custom paper sizes.
(1) Open the Printer folder.
See 3.1.1(1) for instruction on how to open the Printer folder.
(2) Right-click “PT390 Raster” and select [Properties].
* For Windows Vista and Server 2008, if [Run as administrator] is displayed when you right-click a printer name, select [Run as administrator] → [Properties].
If the [User Account Control] dialog is displayed, select [Continue].
* For Windows 7 and Server 2008 R2, right-click a printer name and select [Printer Properties].
Copyright (C) 2012 Oki Data Corporation 11 of 56
Windows Driver User's Guide 1.0.1.1
(3) Click the [Custom Paper] tab.
(4)
(5)
(3)
(7)
(6)
(4) Check [Create a New Paper].
(5) Enter a paper name in [Paper Name].
* The paper name can be unique.
The figure above shows an example with the name "Receipt-A."
(6)
(6) Select the [Unit], and enter the [S1], [S3], [L] and [R] values according to the layout shown in the box.
* Changing between units can result in a rounding error of 0.1mm.
If this happens, set the value again.
* The [Paper Type], [S2], [S4] and [S5] settings are used for label printers.
They cannot be specified for this printer.
In addition, the margins [T] and [B] are fixed at "0.0."
(7) Click the [Save] button.
The created paper is added to the [Paper] list.
(8) Click the [OK] button to close the properties screen.
Copyright (C) 2012 Oki Data Corporation 12 of 56
Windows Driver User's Guide 1.0.1.1
* When printing documents, the registered paper will be available for selection in the [Paper Size] field in the [Printing Preferences] screen.
The figure shows an example named "Receipt-A" that was registered as a custom paper size with a width of 80mm and height of
400mm.
Copyright (C) 2012 Oki Data Corporation 13 of 56
Windows Driver User's Guide 1.0.1.1
3.3 Printing from an Application
You can use the paper types registered with the printer driver to print documents from applications. As an example, this section describes how to print a document on the PT390 printer using WordPad.
(1) Select [Page setup] from the [File] menu of WordPad.
(2) In the [Page Setup] screen, set the Paper Size, Orientation and Margins, and click the [OK] button.
(1)
(2)
(3) Edit the document in the WordPad screen.
(4) Select [Print] from the [File] menu.
(5) The [Print] screen is displayed.
Specify the “PT390 Raster” printer in [Select Printer].
(6) To specify the settings for the printer driver, click the [Preferences] button.
* This button depends on the application.
In Word or Excel, for example, the button name becomes [Properties].
(4)
(5)
(6)
Copyright (C) 2012 Oki Data Corporation 14 of 56
Windows Driver User's Guide 1.0.1.1
(7) The [PT390 Raster Properties] (Printing Preferences) screen is displayed.
Specify the settings and click the [OK] button.
(8) Specify [Page Range] or [Number of copies] as needed, and click the [Print] button.
(8)
(7)
(9) The print data is sent to the printer and the document is printed.
Copyright (C) 2012 Oki Data Corporation 15 of 56
Windows Driver User's Guide 1.0.1.1
3.4 Printing Bar Codes and 2D Codes
This printer driver supports printing of various bar codes and 2D codes. This enables you to print bar code or 2D codes from general applications such as Word or Excel.
How a bar code or 2D code is printed
When the printer driver is used, a number of fonts with names corresponding to types of bar code
(see [1] bar code font) are added to the fonts available in the application. To print text as a bar code, enter the text in the document (see [2] bar code data) and assign the desired bar code font.
The same method can be used to print 2D codes.
[1] Bar code font
[2] Bar code data
When printing, the bar code font is converted into a bar code.
The procedure for printing a bar code or 2D code is as follows.
Instruction on How to Print Bar Code
(1) Start the application and set the paper size for the document.
(2) In the application's edit screen, enter the data to be printed as a bar code or 2D code.
Copyright (C) 2012 Oki Data Corporation 16 of 56
Windows Driver User's Guide 1.0.1.1
(3) Select the entered bar code or 2D code data then use the application's font selection list to select the font corresponding to the type of bar code or 2D code you want to print. The following example prints a "QR code" (a type of 2D code).
(4) Select [Print] from the [File] menu. The [Print] dialog is displayed.
* To specify the bar code or 2D code settings (size, rotation, and so on), click the [Properties] button to open the
[Printing Preferences] screen for the printer driver.
For detailed information on setting the values, please see
"4.6 [Bar Code] Tab".
(5) Click the [OK] button to print out the document.
The text to which the bar code font is assigned is printed as a bar code or 2D code.
Copyright (C) 2012 Oki Data Corporation 17 of 56
Windows Driver User's Guide 1.0.1.1
4 Setting up the Printer Driver
This section describes the functions in the [Printer Properties] and [Printing Preferences] screens.
The figure below shows how the printer driver settings screen is organized. This section describes the settings specific to this printer driver (indicated by ). Please refer to Windows Help for information about the Windows settings (indicated by ).
Printer Properties
General
Sharing
Ports
Advanced
Security
Custom Paper
Printing Preferences
Paper
Paper Cut and
Paper Feed
Graphics
Operation
Bar code
Edit printer name, specify the print settings, and print a test page.
Configure the printer share settings.
Configure the port settings.
Configure the print settings.
Set the printer driver's security.
Create or edit a custom paper size.
Configure the paper settings and display the version information.
<Paper Size, Output Size, Saving Paper, Paper Feed Direction,
Print Position Adjustment, Copies, Collate>
Configure the paper cut and feeder.
<Paper Cut, Paper Feed, Top of Form Position,
Reducing Blank lines, Skip Blank Pages>
Configure the graphics settings.
<Color, Half toning, Max Speed, Print Density, BK Density>
Configure the operational settings.
<Drawer, Buzzer, Logo Printing>
Configure the bar code and 2D code settings.
<Bar Code Settings>
Copyright (C) 2012 Oki Data Corporation 18 of 56
4.1 [Custom Paper] Tab
Windows Driver User's Guide 1.0.1.1
Administrative privileges are required to change the [Custom Paper] settings.
Log on with an Administrator account to change the settings.
If you are using Windows Vista or Server 2008, open the properties for the printer from [Run as administrator]. If you are using Windows 7 or Server 2008 R2, open “Printer Properties”. For more information, please see "3.1.1 How to Display the Printer Properties."
Setting
Paper
Create a New Paper
Delete
Save
Transfer to Printer
Description and Setting Options or Range
Lists the registered custom paper sizes.
Select this checkbox if you want to create a new paper size.
Clear if you want to edit a paper size that has already been registered
(the paper size selected in the [Paper] list).
Deletes the paper size selected in the [Paper] list.
Saves the paper size.
If you selected [Create a New Paper], the new paper size is added to the [Paper] list. If [Create a New Paper] is cleared, saving overwrites the paper size selected in the [Paper] list.
* This setting only applies to label printers.
It appears grayed out for this printer and cannot be selected.
Copyright (C) 2012 Oki Data Corporation 19 of 56
Windows Driver User's Guide 1.0.1.1
Setting
Paper Name
Paper Type
[S1]Paper Width
[S2]Label Width
[S3]Paper Height
[S4]Between Labels
[S4]BM Length
[S5]Cut Position
Description and Setting Options or Range
Specify the name of the paper size.
The name can be unique.
The name can be entered if you select [Create a New Paper].
Specify the type of the paper that you create or modify.
* This setting only applies to label printers.
It does not need to be specified for this printer.
Use “Normal”.
Selection
Normal
Specify the width of the paper.
If you selected an existing custom paper size, the width of the custom paper size is displayed.
Setting range
58.0 - 83.0mm (2.28 - 3.27inch)
Specify the width of the label that you create or modify.
* This setting only applies to label printers.
It appears grayed out for this printer and cannot be selected.
Specify the height of the paper that you create or modify.
If you selected an existing custom paper size, the height of the custom paper size is displayed.
Setting range
25.4 - 2039.9mm (1.00 - 80.31inch)
Specify the interval between the labels or the BM length.
* This setting only applies to label printers.
It appears grayed out for this printer and cannot be selected.
Specify the cut position.
* This setting only applies to label printers
It appears grayed out for this printer and cannot be selected.
Specify the left and right margins. Margin [L]Left
[B]Bottom
* For this printer, [T] and [B] are fixed as "0.0mm."
Unit Specify the units for the paper size dimensions.
Setting
0.1mm
0.01inch
Displays in millimeters.
Displays in inches.
Copyright (C) 2012 Oki Data Corporation 20 of 56
Windows Driver User's Guide 1.0.1.1
Setting
Paper Size
Description and Setting Options or Range (*: Default Value)
Specify the size of the paper.
Selection
83 x 297 mm (53 column)
* 80 x 297 mm (48 column)
80 x 297 mm (42 column)
60 x 297 mm (36 column)
58 x 297 mm (35 column)
58 x 297 mm (32 column)
<Guide>
In addition to the above defaults, any paper sizes you have defined using [Custom Paper] are also available.
For custom paper sizes, the paper size is displayed after the paper name.
Copyright (C) 2012 Oki Data Corporation 21 of 56
Setting
Output Size
Transfer to Printer
Windows Driver User's Guide 1.0.1.1
Description and Setting Options or Range (*: Default Value)
Specify whether to print the document scaled to match the selected paper size (output).
Selection
* Same as Paper Size
<Paper smaller than the paper size>
Uses the size specified in [Paper Size].
The document is printed with no scaling.
(Normal printing)
Prints the document scaled to match the specified paper size.
Only paper sizes with a print area smaller than the paper set in [Paper Size] can be specified.
<Guide>
This setting is available when “Off” is selected for [Saving Paper].
Warning when using scaling
Problems with print quality such as ink bleed may occur if the specified size is too small or depending on the size or type of characters being printed. Use the preview image on the right of the screen to check the scaling before printing the document scaled to the size.
The bar codes and logos predefined in the printer driver are printed without scaling. If a bar code cannot fit within the downscaled paper, it is not printed. Also, the bar code and other print data may overlap depending on the print position. In this case, the bar code size and print position should be adjusted before printing.
* This setting only applies to label printers.
It appears grayed out for this printer and cannot be selected.
Copyright (C) 2012 Oki Data Corporation 22 of 56
Setting
Saving Paper
Orientation
Windows Driver User's Guide 1.0.1.1
Description and Setting Options or Range (*: Default Value)
Specify whether to scale the print data vertically to save paper.
Selection
* Off Prints the document normally without saving paper.
(Normal printing)
1/4
1/2
Shrinks the document vertically to save
1/4 of the paper.
Shrinks the document vertically to save
1/2 of the paper.
<Guide>
This setting can be specified when “Same as Paper Size” is selected in [Output Size].
If “1/4” or “1/2” is specified, blank lines at the bottom of the paper are automatically deleted when printing.
Warning when performing saving (scaling) print
Problems with print quality such as ink bleed may occur depending on the size or type of character. Check the print quality when using this function.
The bar codes and logos predefined in the printer driver are printed without scaling. If a bar code cannot fit within the downscaled paper, it is not printed. Also, the bar code and other print data may overlap depending on the print position. In this case, the bar code size and print position should be adjusted before printing.
Specify the orientation of the document to be printed.
Selection
* Portrait Prints the document vertically.
Feeding direction
Landscape Prints the document horizontally.
Feeding direction
Copyright (C) 2012 Oki Data Corporation 23 of 56
Windows Driver User's Guide 1.0.1.1
Setting
Rotate 180
Print Position Adjustment
Description and Setting Options or Range (*: Default Value)
Specify whether to rotate 180 degrees to print the document.
Selection
On (Selected)
Prints the document without rotating 180 degrees.
Orientation = Portrait Landscape
Feeding direction
Prints the document after rotating 180 degrees.
Orientation = Portrait Landscape
Feeding direction
Aligns the print start position.
Horizontal (X) Direction
Aligns the horizontal position relative to the feeding direction. If a negative value is specified, the left margin is decreased. If a positive value is specified, the left margin is increased.
Vertical (Y) Direction
Aligns the vertical position relative to the feeding direction. If a negative value is specified, the top margin is decreased. If a positive value is specified, the top margin is increased.
Setting range
Horizontal (X) Direction
±Paper Width (*Default value: 0.0mm, Range: 0.5mm)
Vertical (Y) Direction
±Paper Height (*Default value: 0.0mm, Range: 0.5mm)
Feeding direction
<Guide>
This setting does not apply to logo printing.
Copyright (C) 2012 Oki Data Corporation 24 of 56
Windows Driver User's Guide 1.0.1.1
Setting
Number of Copies
Collate
Description and Setting Options or Range (*: Default Value)
Specify the number of copies to print.
Setting range
1 - 999 (* Default value: 1)
Specify whether multiple copies of the document are printed by document or by page.
Selection
* Off (cleared) Prints the copies of the document by page.
On (selected) Prints the copies of the document by document.
Paper Cut and Paper Feed Opens the [Paper Cut and Paper Feed] dialog box.
Version
For information on the [Paper Cut and Paper Feed] dialog box, please see Chapter 4.3.
Opens the [Version] dialog.
Default Settings
The version of this printer driver is displayed.
Resets the settings in the [Paper] tab to the default (initial) value.
Copyright (C) 2012 Oki Data Corporation 25 of 56
Windows Driver User's Guide 1.0.1.1
4.3 [Paper Cut and Paper Feed] Dialog Box
Setting
Start of Document
Paper Cut
Paper Feed
Description and Setting Options or Range (*: Default Value)
Specify whether to perform a paper cut and feed when printing starts.
Specify whether to perform a paper cut when printing starts.
Selection
* Off Do not cut the paper.
On (Partial Cut)
On (Full Cut)
Partially cuts the paper.
Fully cuts the paper.
<Guide>
For the partial cut model, it partially cuts the paper even if you specified
“Full Cut”.
Specify whether to perform a paper feed when printing starts.
* This setting only applies to label printers.
It appears grayed out for this printer and cannot be selected.
Copyright (C) 2012 Oki Data Corporation 26 of 56
Setting
End of Page
Paper Cut
Paper Feed
End of Document
Paper Cut
Paper Feed
Windows Driver User's Guide 1.0.1.1
Description and Setting Options or Range (*: Default Value)
Specify whether to perform a paper cut and feed at the end of each page.
Specify whether to perform a paper cut at the end of each page.
Selection
Off
* On (Partial Cut)
Do not cut the paper.
Partially cuts the paper.
On (Full Cut) Fully cuts the paper.
<Guide>
For the partial cut model, it partially cuts the paper even if you specified
“Full Cut”.
Specify whether to perform a paper feed at the end of each page.
* This setting only applies to label printers.
It appears grayed out for this printer and cannot be selected.
Specify whether to perform a paper cut and feed at the end of each document.
Specify whether to perform a paper cut at the end of each document.
Selection
Off
* On (Partial Cut)
On (Full Cut)
<Guide>
Do not cut the paper.
Partially cuts the paper.
Fully cuts the paper.
For the partial cut model, it partially cuts the paper even if you specified
“Full Cut”.
Specify whether to perform a paper feed at the end of each document.
* This setting only applies to label printers.
It appears grayed out for this printer and cannot be selected.
Copyright (C) 2012 Oki Data Corporation 27 of 56
Windows Driver User's Guide 1.0.1.1
Setting
Top of Form Position
Reducing Blank Lines
Skip Blank Pages
If invalid paper size is setup, the printer prints it with the setting of the printer driver
Description and Setting Options or Range (*: Default Value)
Specify the print position from the top edge of the paper.
Selection
* 12.0mm Starts to print the document at 12.0mm from the top edge of the paper.
4.5mm Starts to print the document at 4.5mm from the top edge of the paper.
Specify whether to save paper by not feeding the margin if there is no print data at the bottom (bottom edge if [Orientation] is “Portrait”, or right edge if [Orientation] is “Landscape”) of the print image.
Setting
Off Feeds the paper to the specified paper-length position even if there is no print data in the page.
* On Saves paper by not feeding when there is no print data in the page.
<Guide>
This setting can be specified when “Off” is selected in [Saving Paper].
Specify whether to save paper by not outputting blank pages.
Setting
* Off Prints blank pages.
Outputs a blank page for pages with no print data.
On Does not print blank pages.
Does not output a blank page for pages with no print data.
Specify whether to print the document using the settings from the driver properties if the application specifies an undefined paper size
(dmPaperSize).
The recommended setting is “Off”. However, turn this setting on if documents printed by an application do not have the expected size or the paper is not cut correctly.
Selection
* Off (cleared)
On (selected))
Prints the document based on the other paper definition (dmFormName) if an undefined paper is specified in dmPaperSize.
Prints the document based on the driver properties if an undefined paper is specified in dmPaperSize.
Copyright (C) 2012 Oki Data Corporation 28 of 56
Setting
OK
Cancel
Default Settings
Help
Windows Driver User's Guide 1.0.1.1
Description and Setting Options or Range (*: Default Value)
Closes this dialog box and saves the changes.
Closes this dialog box without saving the changes.
Resets the settings in the [Paper Cut and Paper Feed] dialog box to their default (initial) values.
Displays help for this dialog box.
Copyright (C) 2012 Oki Data Corporation 29 of 56
Windows Driver User's Guide 1.0.1.1
Setting Item
Color
Half toning
Max Speed
Copyright (C) 2012 Oki Data Corporation
Description and Setting Options or Range (*: Default Value)
Specify a color mode.
Selection
* Mono
2 Color
Prints the document in monochromatic.
Prints the document in two colors.
<Guide>
To print the document with “2 Color”, please use the paper for two-colors.
Specify how to perform half toning when colors are converted to black and white.
Selection
* Dither 6x6
Dither 8x8
Prints the image with fine mesh pattern.
The gradation range is relatively narrower.
Prints the image with coarse mesh pattern.
The gradation range is relatively wider.
Sets the print speed.
Selection
* Depending on
Printer Setting
1st (Low Speed)
:
11th (High Speed)
Prints the document using the printer setup settings.
You can select a speed from 1st (Low
Speed) to 11th (High Speed).
30 of 56
Setting Item
Print Density
BK Density
Default Settings
Windows Driver User's Guide 1.0.1.1
Description and Setting Options or Range (*: Default Value)
Specify the print density.
Selection
* Depending on Prints the document using the printer setup settings. Printer Setting
130% (Darkest)
:
70% (Lightest)
You can select a darkness by units of 5% from 130% (darkest) to 70% (lightest).
Specify the black density when printing the document in two colors.
Selection
* Depending on
Printer Setting
Prints the document using the printer setup settings.
130% (Darkest)
:
* 100%
:
70% (Lightest)
You can select a darkness by units of 5% from 130% (darkest) to 70% (lightest).
<Guide>
This setting can be specified when “2 Color” is selected in [Color].
Resets the settings in the [Graphics] tab to the default (initial) value.
Copyright (C) 2012 Oki Data Corporation 31 of 56
Windows Driver User's Guide 1.0.1.1
Setting
Drawer
Drawer #1
Time of Pulse
Drawer #2
Time of Pulse
Description and Setting Options or Range (*: Default Value)
Specify the kick behavior of the drawers.
Specify the kick behavior of drawer #1.
Selection
* None
Start of Document
End of Document
Does not open drawer #1.
Opens drawer #1 when printing starts.
Opens drawer #1 when printing ends.
Specify the kick time (in milliseconds) when drawer #1 is open.
Setting range
* 20ms
| (Range: 20ms)
500ms
Specify the kick behavior of drawer #2.
Selection
* None
Start of Document
End of Document
Does not open drawer #2.
Opens drawer #2 when printing starts.
Opens drawer #2 when printing ends.
Specify the kick time (in milliseconds) when drawer #2 is open.
Setting range
* 20ms
| (Range: 20ms)
500ms
Copyright (C) 2012 Oki Data Corporation 32 of 56
Setting
Buzzer
Beep
Buzzer Pattern
Repeat
Play
Windows Driver User's Guide 1.0.1.1
Description and Setting Options or Range (*: Default Value)
Specify the behavior of the buzzer.
Specify when to ring the buzzer.
Selection
* None
Start of Document
End of Document
The buzzer does not ring.
The buzzer rings when printing starts.
The buzzer rings when printing ends.
Specify a sound pattern for the buzzer.
Selection
* Depending on Printer Setting The buzzer rings according to the printer settings.
Pattern 1 Uses Pattern 1
(40ms ON / 120ms OFF).
Pattern 2
Pattern 3
Uses Pattern 2
(140ms ON / 140ms OFF).
Uses Pattern 3
(200msON / 200msOFF).
Pattern 4
Pattern 5
Uses Pattern 4
(10msON / 50msOFF).
Uses Pattern 5
(30msON / 50msOFF).
Specify the number of repetitions for the buzzer.
Setting range
1 - 5 (* Default value: 3)
<Guide>
This setting can be specified when other than “Depending on Printer
Setting” is selected in [Buzzer Pattern].
The pattern specified in [Buzzer Pattern] and [Repeat] is played back.
Click if you want to check how the buzzer actually sounds on the printer.
To play the sound, ensure that the printer is connected and ready to print before clicking the button.
Copyright (C) 2012 Oki Data Corporation 33 of 56
Setting
Logo Printing
Start of Document
Start of Page
End of Document
Windows Driver User's Guide 1.0.1.1
Description and Setting Options or Range (*: Default Value)
Specify how to perform logo printing.
<Guide>
Before printing a logo, use the utility to register the logo with the printer.
For information on how to register logos, please see "3.4 Setting a
Logo" of "Utility User's Guide."
Specify the logo to print when printing starts.
Selection
* None
Logo 1 (2020)
|
Logo 60 (205B)
Does not print a logo when printing starts.
Prints the specified logo when printing starts.
The number in the brackets is the key code of the logo registered in the printer. The keycode can be checked using the utility.
Specify the logo to print at the start of each page.
Selection
* None Does not print the logo at the head of the page.
Prints the specified logo at the head of the Logo 1 (2020)
|
Logo 60 (205B) page.
The number in the brackets is the key code of the logo registered in the printer. The keycode can be checked using the utility.
Specify the logo to print at the end of each document.
Selection
* None
Logo 1 (2020)
|
Logo 60 (205B)
Does not print the logo when printing ends.
Prints the specified logo when printing ends.
The number in the brackets is the key code of the logo registered in the printer. The keycode can be checked using the utility.
Copyright (C) 2012 Oki Data Corporation 34 of 56
Windows Driver User's Guide 1.0.1.1
Setting
Logo Position
Conform to Print Image
Default Settings
Description and Setting Options or Range (*: Default Value)
Specify where to print the logos specified in [Start of
Document], [Start of Page] or [End of Document].
Selection
Off (cleared) Prints the [Start of Document], [Start of Page] or [End of Document] logo at a position based on the feeding direction without considering the finished print image. The logo is
* On (selected)) printed at a fixed position, ignoring the "Rotate 180" setting of
[Orientation].
Prints the logo at a position determined by the finished print image. If "Rotate 180" is specified in
[Orientation], both the print image and logo are rotated by 180 degrees when printing the document.
Resets the settings in the [Operations] tab to the default (initial) value.
Copyright (C) 2012 Oki Data Corporation 35 of 56
4.6 [Bar Code] Tab
Windows Driver User's Guide 1.0.1.1
You can change the bar code and 2D code settings such as the width or height and set these in the printer driver. Registered bar codes appear as printer fonts in applications. If you assign one of these fonts to text, the corresponding bar code or 2D code is printed.
This section describes the bar codes and 2D codes supported by the printer driver, how to register a new bar code, and how to change existing bar code settings. It also explains each of the settings.
Copyright (C) 2012 Oki Data Corporation 36 of 56
Windows Driver User's Guide 1.0.1.1
4.6.1 List of Supported Bar Codes and 2D Codes
The table below lists the types of bar code and 2D code supported by the printer driver.
The supported bar codes and 2D codes (bar codes and 2D codes supported in [Type]) appear as the initial defaults in the [Bar Code Font List].
: Supported,
: Unsupported
Bar code font name initially registered in the Bar Code Font List
Bar Code Types
Codabar Codabar
Code 128 Code 128
Code 39
Code 93
Code 39
Code 93
EAN 13(JAN 13)
EAN 8(JAN 8)
EAN 13(JAN 13)
EAN 8(JAN 8)
ITF ITF
UPC type A UPC type A
UPC type E
DataMatrix Code
PDF417 Code
UPC type E
DataMatrix Code
QR Code
PDF417 Code
QR Code
PT390
Copyright (C) 2012 Oki Data Corporation 37 of 56
Windows Driver User's Guide 1.0.1.1
4.6.2 How to Register a New Bar Code Font
(1) Open the printer driver's print settings from the printer folder.
(2) Open the [Bar Code] tab and select the [Create a New Bar Code] checkbox. (New creation mode)
To copy font settings from an existing bar code or 2D code, select the bar code font from [Bar
Code Font List].
↓
The name and settings of the selected bar code font appear in [Bar Code Font Name] and [Bar
Code Settings].
(3) Enter the new bar code font name in [Bar Code Font Name].
(4) Make any changes to [Bar Code Settings].
(5) Click [Add].
↓
The bar code font is added to [Bar Code Font List].
The added font is listed alphabetically (in ascending order) sorted by whether they are 1D or
2D.
* If you select another item from [Bar Code Font List] without clicking [Add], the changes made in steps (3) and (4) are discarded.
(6) Click [Apply] or [OK] to apply the added settings to the driver.
* Note that if you click [Add] and then [Cancel], the settings will not be applied.
4.6.3 How to Change Bar Code Font Settings
(1) Open the printer driver's print settings from the printer folder.
(2) Open the [Bar Code] tab and clear the [Create a New Bar Code] checkbox. (Edit mode)
(3) Select a bar code font to edit from [Bar Code Font List].
↓
The name and settings of the selected bar code font appear in [Bar Code Font Name] and [Bar
Code Settings].
(3) Make any changes to [Bar Code Settings].
(4) Click [Apply] or [OK] to apply the added settings to the driver.
* If you select another item from [Bar Code Font List], any changes you made will remain available temporarily. However, you need to click [Apply] or [OK] to apply the settings to the driver.
Copyright (C) 2012 Oki Data Corporation 38 of 56
Windows Driver User's Guide 1.0.1.1
4.6.4 Setting Items (for all Bar Codes)
Setting
Bar Code Font List
Delete
Description and Setting Options or Range (*: Default Value)
Lists the bar code fonts registered with the driver.
<Guide>
Bar code fonts in this list are registered in the operating system
(OS) as printer fonts and become available for use in applications.
The bar codes or 2D codes supported by the printer driver are set as defaults.
For more information, please see "4.6.1 List of Supported Bar
Codes/2D Codes."
Up to 30 fonts can be registered (including those initially registered).
The bar code fonts in the list appear alphabetically (in ascending order) sorted by whether they are 1D or 2D.
Deletes the bar code font selected in [Bar Code Font List].
<Guide>
This setting is available if:
You open the driver properties (Printing Preferences screen) from the printer folder.
You cannot specify the setting when you open the driver properties from an application.
Copyright (C) 2012 Oki Data Corporation 39 of 56
Setting
Create a New Bar Code
Bar Code Font Name
Add
Windows Driver User's Guide 1.0.1.1
Description and Setting Options or Range (*: Default Value)
Select if you want to create a new bar code font.
Selection
* Off (cleared)
On (selected))
Edit mode
Use this to edit the settings of a registered bar code font (the font selected in [Bar Code Font List]).
Create mode
Use this to create a new bar code font.
The font is registered in [Bar Code
Font List] by clicking the [Add] button.
<Guide>
This setting is available if:
You open the driver properties (Printing Preferences screen) from the printer folder.
The number of registered bar code fonts is less than the maximum (30).
Enter the name of the new bar code font.
<Guide>
This setting is available if:
You open the driver properties (Printing Preferences screen) from the printer folder.
You specified create mode (the [Create a New Bar Code] checkbox is selected).
Up to 31 characters (for 1-byte) or 15 characters (for 2-byte) can be entered. The following characters cannot be used:
Space (blank) at the head or tail of the name
"@"
Adds the bar code font [Bar Code Font List]. The settings specified in [Bar Code Settings] are saved.
<Guide>
This setting is available if:
You open the driver properties (Printing Preferences screen) from the printer folder.
You specified create mode (the [Create a New Bar Code] checkbox is selected).
There is no font with the same name in [Bar Code Font List] or registered in the system (OS).
Copyright (C) 2012 Oki Data Corporation 40 of 56
Setting
Bar Code Settings
Type
Replacement Font
Windows Driver User's Guide 1.0.1.1
Description and Setting Options or Range (*: Default Value)
Specify the various settings for the bar code or 2D code in create or edit mode.
Specify the type of bar code or 2D code.
For information on the available code types, please see "4.6.1
List of Supported Bar Codes/2D Codes."
<Guide>
This setting is available if:
You open the driver properties (Printing Preferences screen) from the printer folder.
If you change this setting, the other [Bar Code Settings] are updated with the default values for the new [Type].
Use this setting if you want to print using the bar code or 2D code selected in [Type] in place of a font registered in Windows.
Selection
* None
(Font registered in
Windows)
Does not replace a
Windows-registered font with a bar code or 2D code when printing.
Instead, only prints a bar code or 2D code for the bar code or 2D code type selected in [Type].
Replaces the specified
Windows-registered font with the bar code or 2D code selected in
[Type].
Resets the settings of the bar code (2D code) selected in [Type] to the default (initial) value.
Default Settings
Copyright (C) 2012 Oki Data Corporation 41 of 56
Windows Driver User's Guide 1.0.1.1
4.6.5 Bar Code Settings
Setting
Type
Replacement Font
Width
Height
HRI Text
HRI Font
Rotation
Description and Setting Options or Range (*: Default Value)
Please see "4.6.4 Setting Items (for all Bar Codes)."
Please see "4.6.4 Setting Items (for all Bar Codes)."
Specify the width of the narrow bar. (by 1/203 inch.)
Setting range
1 - 6 *Default value: 2
<Guide>
A setting of at least two dots is recommended for the [Width]. When using a one-dot width, be sure to carefully evaluate factors such as the bar code reader, the paper, and the printer's print darkness settings.
Specify the height of the bar code. (by 1/203 inch.)
Setting range
1 - 255 *Default value: 162
Specify whether and how to print the HRI text.
Selection
* None
Top
Bottom
Top and Bottom
Does not print the HRI text.
Prints the HRI text above the bar code.
Prints the HRI text below the bar code.
Prints the HRI text above and below the bar code.
Specify the typeface for the HRI text.
This setting can be specified when “Print Top (Bottom, or Top and
Bottom)” is selected in [HRI Text].
Selection
* Font A
Font B
Font C
Prints the HRI text with Font A.
Prints the HRI text with Font B.
Prints the HRI text with Font C.
Specify the rotation angle for the bar code.
Selection
* 0 degrees Prints the bar code based on the
[Orientation] setting, without rotating it.
90 degrees
180 degrees
Prints the bar code, rotating 90 degrees relative to the [Orientation] setting.
Prints the bar code, rotating 180 degrees relative to the [Orientation] setting.
270 degrees Prints the bar code, rotating 270 degrees relative to the [Orientation] setting.
Copyright (C) 2012 Oki Data Corporation 42 of 56
Windows Driver User's Guide 1.0.1.1
<Guide>
For Code 39 bar codes:
- Alphabetical characters (A - Z) should be specified in uppercase.
- The start and stop codes (*) are automatically appended by the printer.
- If '*' exists in the string, the bar code is printed up to '*'. The subsequent string is printed as normal text.
For Code128 bar codes:
- Append the start code ({A,{B,{C * 1-byte) at the head of the string.
If there is no start code, the Code128 bar code is not printed.
- For the start code C, the code or function should not be specified except at the head of the string.
For ITF bar codes:
- You can only specify even number of characters.
If an odd number of characters is specified, one letter at the end of the string is omitted to create the bar code.
Copyright (C) 2012 Oki Data Corporation 43 of 56
Windows Driver User's Guide 1.0.1.1
4.6.6 DataMatrix Code Settings
Setting
Replacement Font
Type
Square Size
Rectangle Size
Cell Size
Rotation
Description and Setting Options or Range (*: Default Value)
Please see "4.6.4 Setting Items (for all Bar Codes)."
Specify the type, square or rectangle.
Selection
* Square
Rectangle
Specify the size of the square.
Setting Range
0, 10 - 144 * Default value: 0 (Auto)
Specify the size of the rectangle.
Selection
* 18x8
32x8
26x12
36x12
36x16
48x16
Specify the size of the cell.
Setting Range
3 - 16 * Default value: 5
Specify the rotation angle for the DataMatrix Code.
Selection
* 0 degrees
90 degrees
Prints the DataMatrix Code based on the
[Orientation] setting, without rotating it.
Prints the DataMatrix Code, rotating 90 degrees relative to the [Orientation] setting.
180 degrees
270 degrees
Prints the DataMatrix Code, rotating 180 degrees relative to the [Orientation] setting.
Prints the DataMatrix Code, rotating 270 degrees relative to the [Orientation] setting.
Copyright (C) 2012 Oki Data Corporation 44 of 56
Windows Driver User's Guide 1.0.1.1
4.6.7 PDF417 Code Settings
Setting
Replacement Font
Column
Row
Width
Height
Error Correction
Compact PDF
Description and Setting Options or Range (*: Default Value)
Please see "4.6.4 Setting Items (for all Bar Codes)."
Specify the number of columns.
Setting Range
0 - 30 * Default value: 0 (Auto)
Specify the number of rows.
Setting Range
0, 3 – 90 * Default value: 0 (Auto)
Specify the width.
Setting Range
2 - 8 * Default value: 3
Specify the height.
Setting Range
2 - 8 * Default value: 3
Specify the error correction level of the PDF417 code.
Selection
Level 0
* Level 1
Level 2
Level 3
Level 4
Level 5
Level 6
Level 7
Level 8
Specify this setting if the PDF417 code is printed as a Compact PDF.
Selection
* Off (Unchecked)
On (Checked)
Copyright (C) 2012 Oki Data Corporation 45 of 56
Windows Driver User's Guide 1.0.1.1
Setting
Rotation
Description and Setting Options or Range (*: Default Value)
Specify the rotation angle for the PDF417 Code.
Selection
* 0 degrees Prints the PDF417 Code based on the
[Orientation] setting, without rotating it.
90 degrees
180 degrees
270 degrees
Prints the PDF417 Code, rotating 90 degrees relative to the [Orientation] setting.
Prints the PDF417 Code, rotating 180 degrees relative to the [Orientation] setting.
Prints the PDF417 Code, rotating 270 degrees relative to the [Orientation] setting.
<Guide>
If the Column = 0 and Row = 0 (default value), the PDF417 Code is printed by calculating the number of rows based on the minimum number of columns.
Copyright (C) 2012 Oki Data Corporation 46 of 56
Windows Driver User's Guide 1.0.1.1
4.6.8 QR Code Settings
Setting
Replacement Font
Cell Size
Model
Error Correction
Rotation
Description and Setting Options or Range (*: Default Value)
Please see "4.6.4 Setting Items (for all Bar Codes)."
Specify the size of the cell.
Setting range
3 - 12 * Default value: 4
Specify the type of the QR code.
Selection
Model 1
* Model 2
Micro
Specifies QR code model 1.
Specifies QR code model 2.
Specifies a micro QR code.
Specify the error correction level of the QR code.
Selection
* Level L Can be restored if about 7% of the code is damaged.
Level M
Level Q
Level H
Can be restored if about 15% of the code is damaged.
Can be restored if about 25% of the code is damaged.
Can be restored if about 30% of the code is damaged.
This setting cannot be specified when
[Model] is [Micro].
Specify the rotation angle for the QR Code.
Selection
* 0 degrees Prints the QR Code based on the
[Orientation] setting without rotating it.
90 degrees
180 degrees
270 degrees
Prints the QR Code rotated 90 degrees relative to the [Orientation] setting.
Prints the QR Code rotated 180 degrees relative to the [Orientation] setting.
Prints the QR Code rotated 270 degrees relative to the [Orientation] setting.
Copyright (C) 2012 Oki Data Corporation 47 of 56
Windows Driver User's Guide 1.0.1.1
5 Displaying Printer Status Information
The PT390 printer driver displays printer status information in the printer folder or spooler window when using a serial, parallel or USB interface connection.
Displayed in “Status” in the printer folder
Displayed in the title bar of the spooler
The displayed information may vary depending on the OS.
The following table shows the examples for Windows XP and Windows 7.
<Example of Printer Status Information>
Printer Status
[Status] in Printer Folder
Windows XP Windows 7
Offline Offline (None Offline Offline
Cover Open Door Open
Offline
Busy
Door open Door Open
Offline
Busy
Door Open
Offline
Busy
Paper Out
Head Hot
Out Of Paper
Offline
Busy
Offline
Busy
Paper out
(None displayed)
Out of Paper
Offline
Busy
Offline
Busy
Out of Paper
Offline
Busy
Offline
Busy
Hardware
Error
Communication
Error
Offline
Not Available
Not Available
Not Available
Not Available
Not Available
Offline
Not Available
Not Available
Offline
Not Available
Use Printer Offline
Title Bar of Spooler
Windows XP Windows 7
Copyright (C) 2012 Oki Data Corporation 48 of 56
Windows Driver User's Guide 1.0.1.1
<Guide>
The printer status information can be displayed when using a serial, parallel or USB interface connection. It is not available when using a LAN interface.
Note that the USB interface uses the printer class. The virtual COM class cannot be used. The [USB] setting in the Printer Setup should be left as “Printer”.
The printer status information can be displayed when bi-directional communications is enabled for the printer driver.
The default setting in the PT390 printer driver is enabled, so no changes are required.
If using the serial interface, the printer status information does not display a “Communication Error” if you turn off the printer when any of the following errors occur during printing.
Head hot
Paper Out
Cover Open
Hardware Error
Printer status information is not supported when multiple printers are connected. If multiple printers are connected, valid status information is not displayed.
If you are using the serial interface, a baud rate of 115200bps is recommended.
If you use the parallel interface, the powered-off status cannot be detected for up to 90 seconds after the printer is turned off.
Copyright (C) 2012 Oki Data Corporation 49 of 56
Windows Driver User's Guide 1.0.1.1
The printer status information cannot be used if you run any applications that send control commands to the printer. The application malfunctions because it sends and receives commands to get the printer status information. In this case, disable the bi-directional communication function in the printer driver
(uncheck [Enable bidirectional support]) before running the application.
Copyright (C) 2012 Oki Data Corporation 50 of 56
Windows Driver User's Guide 1.0.1.1
6 Precautions for Use
6.1 Warnings for Printer Driver Settings
(1) Do not select the [Hold mismatched documents] checkbox in the [Advanced] tab. Otherwise, the message "Invalid print setting" is displayed (in the status on the spooler) and the document cannot be printed.
(2) Set [Enable bidirectional support] in the [Ports] tab of the Printer Properties as follows depending on the interface being used.
- If using a serial, parallel or USB interface: Selected (Default)
- If using a LAN interface (PR-PortManager): Cleared
(3) To use a USB connection to connect two or more of this model of printer:
To add more printers, follow these steps to install the printer driver:
1. Set [Serial No] to “Enable” when adding each printer.
2. Install the printer driver again.
* The printer setup can be performed from the utility. Please see "Utility User's Guide" for information on how to use the utility. See "3. Installation" of "Printer Driver Installation
Guide" for information on how to install the printer driver.
Copyright (C) 2012 Oki Data Corporation 51 of 56
Windows Driver User's Guide 1.0.1.1
(1) If printing a document from application software designed for a different version of the Windows operating system, the printout may be different to that version of Windows.
(2) Depending on the application that you use, the document may not be printed properly if you decrease the margin. In the case of the printer driver’s default paper sizes, set the margins to values greater than those shown below.
For custom paper sizes, set the margin when you define the custom paper size.
Paper Size
83 x 297 mm (53 column)
80 x 297 mm (48 column)
80 x 297 mm (42 column)
60 x 297 mm (36 column)
58 x 297 mm (35 column)
58 x 297 mm (32 column)
Left
Margin
1.0
4.0
8.0
Orientation: Portrait
Right
Margin
Top
Margin
Bottom
Margin
Left
Orientation: Landscape
Margin
Right
Margin
Top
Margin
Bottom
Margin
2.0 0.0 0.0 0.0 0.0 2.0 1.0
4.0 0.0 0.0 0.0 0.0 4.0 4.0
8.0 0.0 0.0 0.0 0.0 8.0 8.0
3.0 2.5 0.0 0.0 0.0 0.0 2.5 3.0
3.0 2.5 0.0 0.0 0.0 0.0 2.5 3.0
5.0 5.0 0.0 0.0 0.0 0.0 5.0 5.0
[Unit : mm]
(3) If you want to print multiple copies, select the collate checkbox. Depending on the application that you use, the document may not be printed properly if you clear the collate checkbox. For applications (such as Microsoft Excel) that print multiple copies by creating multiple print jobs, the
[End of Document]-[Paper Cut] setting may not work correctly.
(4) If using this printer driver to collate copies, the maximum number allowed in the application is
"999."
To set a higher number, print the job multiple times.
Copyright (C) 2012 Oki Data Corporation 52 of 56
Windows Driver User's Guide 1.0.1.1
6.3 Bar Code and 2D Code Warnings
(1) The bar code fonts provided by the printer driver are defined as printer fonts. These printer fonts may not appear in the font list of some applications. In this case, you can still print bar codes by using the [Replacement Font] setting to specify substitution of a Windows font with a bar code font.
(2) If an application has a font substitution function, the bar code font may be replaced by a different font in the application.
(3) A bar code may not be printed if it exceeds the print area for the specified paper due to the settings (narrow bar or rotation, etc.), position, or number of characters. Check the printed result to set the values.
(4) Do not apply effects (such as bold, italic or outline) when using bar code fonts. Note that the bar code is not printed properly for vertical or wrapped text.
(5) The printed bar code is not displayed on the application screen.
Adjust the position to avoid the bar code or 2D code from overlapping the neighboring characters.
The same bar code or 2D code cannot be printed repeatedly on the same line.
(6) Some applications do not send 2- or 1-byte spaces at the end of strings to the printer driver correctly. If 2- or 1-byte space is specified at the end of the string from an application, the bar code may not print as expected.
(7) Restrictions for 2D codes
Depending on the application, 2-byte spaces in the specified string are printed as 1-byte spaces.
(8) Bar code and 2D code data
If the number of characters in the bar code text is invalid (too many or too few), it is not printed.
-
The following table lists the available character sets and string lengths for bar codes and 2D codes.
Copyright (C) 2012 Oki Data Corporation 53 of 56
Windows Driver User's Guide 1.0.1.1
[Bar Code]
Bar Code Type
Codabar
Code 128
Code 39
Code 93
EAN 13 (JAN 13)
EAN 8 (JAN 8)
ITF
UPC type A
UPC type E
[2D Code]
2D Code Type
DataMatrix
PDF417
Available Character Set
Numeral: '0' - '9'
Symbol: '$', '+', '-', '.', '/', ':', '\'
Start/Stop Character: 'A' - 'D' (automatically appended)
Code Set A: '{A' 0x00 - 0x5F
Code Set B: '{B' 0x20 - 0x7F
Code Set C: '{C' 0x00 - 0x63
However, the character '{' is not included.
Numeral: '0' - '9'
Alphabetical: 'A' - 'Z'
Symbol: ' ', '%', '$', '+', '-', '.', '/'
* The start/stop character '*' is automatically appended.
0x00 - 0x7F
Numeral: '0' - '9'
Numeral: '0' - '9'
Numeral: '0' - '9'
Numeral: '0' - '9'
Numeral: '0' - '9'
String Length
1 - 210
3 - 210
1 - 210
1 - 210
12 - 13
7 - 8
2 - 210
11 - 12
11 - 12
QR Code
Available Character Set
All the codes (0x00 - 0xFF)
String Length
Alphanumeral: - 2335
Numeral: - 3116
0x00 - 0xFF. However,
0x00 - 0x7F should conform to the ASCII code, and
0x80 - 0xFF should conform to the extended character set of the English table in PC437
(USA:Standard Europe).
All the codes (0x00 - 0xFF)
Alphanumeral: - 1850
Numeral: - 2710
Model 1
Alphanumeric: - 707
Numeral:
Kanji:
- 1167
- 299
Model 2
Alphanumeric: - 4296
Numeral:
Kanji:
- 7089
- 1817
Micro QR
Alphanumeric: - 21
Numeral:
Kanji:
- 35
- 9
Copyright (C) 2012 Oki Data Corporation 54 of 56
Windows Driver User's Guide 1.0.1.1
(1) If you “cancel” a print job while printing from the printer port, please turn the printer off and on again. If you resume printing a document without restarting the printer, problems such as incorrect print out may occur.
(2) If used with a USB interface on Windows 2000, please turn the printer off and on again after recovering your computer from standby or pause mode. If you print a document without restarting the printer, communication errors may occur and the print job may not be discarded correctly
(3) If you change the port settings in print properties, please restart the computer. If you skip the restart, "Not Available" will be displayed on the spooler and problems such as the print job not completing may occur.
(4) Problems such as failure to print correctly from the OPOS(JavaPOS) driver may occur if the
Windows driver and OPOS(JavaPOS) driver are both installed in the same system. In this case, it is recommended that you uninstall the driver that is not being used.
Copyright (C) 2012 Oki Data Corporation 55 of 56
7 Revision History
Windows Driver User's Guide 1.0.1.1
Revision Updated date
1.0.0.0 First Edition (2011/07/08)
1.0.1.0 2012/03/01
1.0.1.1 2012/08/02
Copyright (C) 2012 Oki Data Corporation 56 of 56
Oki
contact details
OkicontactName. Oki Systems
(UK) Limited
OkicontactAddress.550 Dundee Road
Slough Trading Estate
Slough
Berkshire
SL1 4LE
Oki Systems (Iberica), S.A.U
C/Teide, 3
San Sebastian de los Reyes
28703, Madrid
Tel:+34 91 3431620
Fax: +34 91-3431624
Atención al cliente: 902 36 00 36
Website: www.oki.es
Tel:+44 (0) 1753 819819
Fax:+44 (0) 1753 819899 http://www.oki.co.uk
Oki Systems Ireland Limited
The Square Industrial Complex
Tallaght
Dublin 24
Oki Systèmes (France) S.A.
44-50 Av. du Général de Gaulle
94246 L'Hay les Roses
Paris
Tel:+33 01 46 15 80 00
Télécopie:+33 01 46 15 80 60
Website: www.oki.fr
Tel:+353 (0) 1 4049590
Fax:+353 (0)1 4049591 http://www.oki.ie
Oki Systems Ireland Limited -
Northern Ireland
19 Ferndale Avenue
Glengormley
BT36 5AL
Northern Ireland
OKI Systems (Magyarország) Kft.
Capital Square
Tower 2
7th Floor
H-1133 Budapest,
Váci út 76
Hungary
Tel:+44 (0) 7767 271447
Fax:+44 (0) 1 404 9520 http://www.oki.ie
Telefon: +36 1 814 8000
Telefax: +36 1 814 8009
Website: www.okihu.hu
Technical Support for all Ireland:
Tel:+353 1 4049570
Fax:+353 1 4049555
E-mail: [email protected]
OKI Systems (Czech and Slovak), s.r.o.
IBC – Pobřežní 3
186 00 Praha 8
Czech Republic
Tel: 01805/6544357**
01805/OKIHELP**
Fax: +49 (0) 211 59 33 45
Website: www.okiprintingsolutions.de
**0,14€/Minute aus dem dt. Festnetz der T-Com (Stand 11.2008)
OKI Systems (Italia) S.p.A.
via Milano, 11,
20084 Lacchiarella (MI)
Tel:+39 (0) 2 900261
Fax:+39 (0) 2 90026344
Website: www.oki.it
OKI Printing Solutions
Platinium Business Park II, 3rd Floor ul. Domaniewska 42
02-672 Warsaw
Poland Tel: +420 224 890158
Fax:+420 22 232 6621
Website: www.oki.cz, www.oki.sk
Oki Systems (Deutschland) GmbH
Hansaallee 187
40549 Düsseldorf
Tel:+48 22 448 65 00
Fax:+48 22 448 65 01
Website: www.oki.com.pl
E-mail: [email protected]
Hotline: 0800 120066
E-mail: [email protected]
Oki Systems (Ibérica) S.A.
Sucursal Portugal
Edifício Prime -
Av. Quinta Grande 53
7º C Alfragide
2614-521 Amadora
Portugal
Διανομέας των συστημάτων OKI
CPI S.A1 Rafailidou str.
177 78 Tavros
Athens
Greece
Tel:+351 21 470 4200
Fax:+351 21 470 4201
Website:www.oki.pt
E-mail : [email protected]
Tel: +30 210 48 05 800
Fax:+30 210 48 05 801
EMail:[email protected]
Oki Service
Serviço de apoio técnico ao
Cliente
Tel: 808 200 197
E-mail : [email protected]
OKI Europe Ltd. (Russia)
Office 702, Bldg 1
Zagorodnoye shosse
117152, Moscow
Tel: +74 095 258 6065
Fax: +74 095 258 6070 e-mail: [email protected]
Website: www.oki.ru
Technical support:
Tel: +7 495 564 8421 e-mail: [email protected]
Oki Systems (Österreich)
Campus 21
Businesszentrum Wien Sued
Liebermannstrasse A02 603
22345 Brun am Gebirge
Tel: +43 223 6677 110
Drucker Support:
+43 (0) 2236 677110-501
Fax Support:
+43 (0) 2236 677110-502
Website: www.oki.at
OKI Europe Ltd. (Ukraine)
Raisy Opkinoy Street,8
Building B, 2nd Floor,
Kiev 02002
Ukraine
Tel: +380 44 537 5288 e-mail: [email protected]
Website: www.oki.ua
OKI Sistem ve Yazıcı Çözümleri
Tic. Ltd. Şti.
Harman sok Duran Is Merkezi,
No:4, Kat:6,
34394, Levent
İstanbul
Tel: +90 212 279 2393
Faks: +90 212 279 2366
Web: www.oki.com.tr
www.okiprintingsolutions.com.tr
Oki Systems (Belgium)
Medialaan 24
1800 Vilvoorde
Helpdesk: 02-2574620
Fax: 02 2531848
Website: www.oki.be
AlphaLink Bulgaria Ltd.
2 Kukush Str.
Building "Antim Tower", fl. 6
1463 Sofia, Bulgaria tel: +359 2 821 1160 fax: +359 2 821 1193
Website: http://bulgaria.oki.com
OKI Printing Solutions
Herstedøstervej 27
2620 Albertslund
Danmark
Adm.: +45 43 66 65 00
Hotline: +45 43 66 65 40
Salg: +45 43 66 65 30
Fax: +45 43 66 65 90
Website: www.oki.dk
Oki Systems (Finland) Oy
Polaris Capella
Vänrikinkuja 3
02600 Espoo
Tel: +358 (0) 207 900 800
Fax: +358 (0) 207 900 809
Website: www.oki.fi
Oki Systems (Holland) b.v.
Neptunustraat 27-29
2132 JA Hoofddorp
Helpdesk: 0800 5667654
Tel:+31 (0) 23 55 63 740
Fax:+31 (0) 23 55 63 750
Website: www.oki.nl
Oki Systems (Norway) AS
Tevlingveien 23
N-1081 Oslo
Tel:+47 (0) 63 89 36 00
Telefax:+47 (0) 63 89 36 01
Ordrefax:+47 (0) 63 89 36 02
Website: www.oki.no
General Systems S.R.L.
(Romania)
Sos. Bucuresti-Ploiesti Nr. 135.
Bucharest 1
Romania
Tel: +40 21 303 3138
Fax: +40 21303 3150
Website: http://romania.oki.com
Var vänlig kontakta din Återförsäljare i första hand, för konsultation. I andra hand kontakta
Oki Systems (Sweden) AB
Borgafjordsgatan 7
Box 1191
164 26 Kista
Tel. +46 (0) 8 634 37 00 e-mail: [email protected] för allmänna frågor om
Oki produkter [email protected] för teknisk support gällandes Oki produkter
Vardagar: 08.30 - 12.00,
13.00 - 16.00
Website: www.oki.se
Oki Systems (Schweiz)
Baslerstrasse 15
CH-4310 Rheinfelden
Support deutsch +41 61 827 94 81
Support français +41 61 827 94 82
Support italiano +41 061 827 9473
Tel: +41 61 827 9494
Website: www.oki.ch
Oki Systems (Thailand) Ltd.
1168/81-82 Lumpini Tower,
27th Floor Rama IV Road
Tungmahamek, Sathorn
Bangkok 10120
Tel:(662) 679 9235
Fax:(662) 679 9243/245 http://www.okisysthai.com
Oki Data Americas Inc.(United
States)
2000 Bishops Gate Blvd.
Mt. Laurel, NJ 08054
USA
Oki Systems (Hong Kong) Ltd.
Suite 1908, 19/F, Tower 3,
China Hong Kong City
33 Canton Road, TsimShaTsui,
Kowloon, Hong Kong
Tel: 1-800-654-3282
Fax: 1-856-222-5247 http://WWW.OKIPRINTINGSOLUTIONS.COM http://my.okidata.com
Oki Data Americas Inc.(América
Latina (OTRO))
2000 Bishops Gate Blvd.
Mt. Laurel, NJ 08054
USA
Tel: (852) 3543 9288
Fax: (852) 3549 6040 http:// www.okiprintingsolutions.com.hk
Oki Data Americas Inc.(Canada •
Canadá)
4140 B Sladeview Crescent Units 7&8
Mississauga, Ontario
Canada L 5L 6A1
Oki Data(Australia) Pty Ltd.
Tél: 1905 -6 08 5000
Téléc: 1-905608 5040 http://WWW.OKIPRINTINGSOLUTIONS.COM
Levwl1 67 Epping Road, Macquarie Park
NSW 2113, Australia
Tel: +61 2 8071 0000
(Support Tel: 1800 807 472)
Fax: +61 2 8071 0010 http://www.oki.com.au
Comworth Systems Ltd.
8 Antares Place Mairangi Bay,
Auckland, New Zealand
Tel:(64) 9 477 0500
Fax:(64) 9 477 0549 http://www.comworth.co.nz
Tel (Español): 1-856-222-7496
1-856-222-5276
Fax: 1-856-222-5260
Email: [email protected]
Oki Data de Mexico, S.A. de C.V.
Mariano Escobedo #748, Piso 8
Col. Nueva Anzures
C.P. 11590, México, D.F.
Oki Data(S) P Ltd. Malaysia Rep
Office
Suite 21.03, 21st Floor Menara IGB,
Mid Valley City,
Lingkaran Syed Pura 59200,
Kuala Lumpur, Malaysia
Tel: (60) 3 2287 1177
Fax: (60) 3 2287 1166
Tel: 52-555-263-8780
Fax: 52-555-250-3501 http:// WWW.OKIPRINTINGSOLUTIONS.COM
Oki Data do Brasil, Ltda.
Rua Avenida Alfrefo Egidio de souza Aranha
100-4° andar-Bloco C Ch a cara Santo Antonio
Sao Paulo, Brazil 04726-170
Tel: 55-11-3444-6747 (Grande São
Paulo)
0800-11-5577 (Demais localidades)
Fax: 5511-3444-3501 e-mail: oki serv @okidata.com.br
http://WWW.OKIPRINTINGSOLUTIONS.COM
Oki Data (Singapore) Pte. Ltd.
438A Alexandra Road #02-11/12,
Lobby 3, Alexandra Technopark
Singapore(119967)
Tel:(65) 6221 3722
Fax:(65) 6594 0609 http://www.okidata.com.sg
Oki Data Corporation
4-11-22 Shibaura, Minato-ku,Tokyo
108-8551, Japan www.okiprintingsolutions.com
Download
Advertisement