ProSPray 3.25

owner‘s manual

MODEL:

0558021 0558022

0558048 0558049 wagner-group.com

gb

0218 • Form No. 0558973N

original operating manual

Warning!

Attention: Danger of injury by injection!

Airless units develop extremely high spraying pressures.

PS 3.25

2

1

2

3

Never put your fingers, hands or any other parts of the body into the spray jet!

Never point the spray gun at yourself, other persons or animals.

Never use the spray gun without safety guard.

Do not treat a spraying injury as a harmless cut. In case of injury to the skin through coating materials or solvents, consult a doctor immediately for quick and expert treatment. Inform the doctor about the coating material or solvent used.

The operating instructions state that the following points must always be observed before starting up:

1. Faulty units must not be used.

2.

3.

4.

5.

Secure Wagner spray gun using the trigger lock on the trigger.

Ensure that the unit is properly earthed.

Check allowable operating pressure of high-pressure hose and spray gun.

Check all connections for leaks.

The instructions regarding regular cleaning and maintenance of the unit must be strictly observed.

Before any work is done on the unit or for every break in work the following rules must be observed:

1. Release the pressure from spray gun and hose.

2.

3.

Secure the Wagner spray gun using the trigger lock on the trigger.

Switch off unit.

Be safety conscious!

1 SAfeTy regulATIoNS for AIrleSS

SprAyINg ______________________________ 4

1.1 Explanation of symbols used _____________________4

1.2 Electric safety _________________________________8

1.3 Electrostatic charging

(formation of sparks or flames) ___________________8

2 geNerAl vIeW of ApplIcATIoN __________ 9

2.1 Application ___________________________________9

2.2 Coating materials ______________________________9

3 DeScrIpTIoN of uNIT __________________ 10

3.1 Airless process _______________________________10

3.2 Functioning of the unit ________________________10

3.3 Technical data _______________________________12

3.4 Legend for explanatory diagram PS 3.25 __________11

3.5 Explanatory diagram PS 3.25 ____________________11

3.6 Transportation _______________________________12

3.7 Transportation in vehicle _______________________12

4 STArTINg operATIoN __________________ 12

4.1 High-pressure hose, spray gun and separating oil ___12

4.2 Control panel indicators _______________________13

4.3 Pressure control knob settings __________________13

4.4 Connection to the mains network _______________14

4.5 Cleaning preserving agent when starting-up of operation initially _________________14

4.6 Taking the unit into operation with coating material 14

4.7 Digital Electronic Spray Control (DESC) ___________15

5 SprAyINg TechNIque __________________ 17

6 hANDlINg The hIgh-preSSure hoSe ____ 18

7 INTerrupTIoN of Work ________________ 18

8 cleANINg The uNIT (ShuTTINg DoWN) __ 19

8.1 Cleaning unit from outside _____________________19

8.2 Suction filter _________________________________19

8.3 Cleaning the high-pressure filter ________________20

8.4 Cleaning Airless spray gun _____________________20

9 remeDy IN cASe of fAulTS _____________ 21

10 ServIcINg _____________________________ 22

10.1 General servicing _____________________________22

10.2 High-pressure hose ___________________________22

11 repAIrS AT The uNIT ___________________ 22

11.1 Relief valve __________________________________22

11.2 Inlet and outlet valve __________________________23

11.3 Packings ____________________________________24

11.4 PS 3.25 connection diagram ____________________25

11.5 Digital Electronic Spray Control (DESC)

Error Messages _______________________________25

12 AppeNDIx _____________________________ 26

12.1 Selection of tip _______________________________26

12.2 Servicing and cleaning of Airless hard-metal tips ___26

12.3 Spray gun accessories _________________________27

12.4 Airless tip table ____________________________ 28/29

12.5 TempSpray __________________________________30

12.6 Pump-Runner ________________________________31

AcceSSorIeS for proSprAy 3.25 _________ 32/33

Spare parts list for main assembly __________________ 34/35

Spare parts list for the fluid section ____________________36

Spare parts list for drive assembly ____________________37

Spare parts list of stand _____________________________38

Spare parts list for suction system of stand ______________39

Spare parts list of upright cart assembly ________________40

ImporTANT NoTeS oN proDucT lIABIlITy ___ 41

3+2 yeArS guArANTee for profeSSIoNAl fINIShINg __________________________________ 41

SAleS AND ServIce compANIeS __________ 43/44

3

safety precautions

PS 3.25

1

SAfeTy regulATIoNS for

AIrleSS SprAyINg

1.1

explANATIoN of SymBolS uSeD

This manual contains information that must be read and understood before using the equipment.

When you come to an area that has one of the following symbols, pay particular attention and make certain to heed the safeguard.

Attention





This symbol indicates a potential hazard that may cause serious injury or loss of life. Important safety information will follow.

This symbol indicates a potential hazard to you or to the equipment.

Important information that tells how to prevent damage to the equipment or how to avoid causes of minor injuries will follow.

 Danger of skin injection i









Danger of fire from solvent and paint fumes

Danger of explosion from solvent, paint fumes and incompatible materials

Danger of injury from inhalation of harmful vapors

Notes give important information which should be given special attention.

hAZArD: INjecTIoN INjury

Attention: Danger of injury by injection! A high pressure stream produced by this equipment can pierce the skin and underlying tissues, leading to serious injury and possible amputation.

Do not treat a spraying injury as a harmless cut. In case of injury to the skin through coating materials or solvents, consult a doctor immediately for quick and expert treatment. Inform the doctor about the coating material or solvent used.

preveNTIoN:

• NEVER aim the gun at any part of the body.

•

•

NEVER allow any part of the body to touch the fluid stream. DO NOT allow body to touch a leak in the fluid hose.

NEVER put your hand in front of the gun.

Gloves will not provide protection against an injection injury.

•

•

•

•

ALWAYS lock the gun trigger, shut the fluid pump off and release all pressure before servicing, cleaning the tip guard, changing tips, or leaving unattended. Pressure will not be released by turning off the engine. The

PRIME/SPRAY valve or pressure bleed valve must be turned to their appropriate positions to relieve system pressure.

ALWAYS keep tip guard in place while spraying. The tip guard provides some protection but is mainly a warning device.

ALWAYS remove the spray tip before flushing or cleaning the system.

NEVER use a spray gun without a working trigger lock and trigger guard in place.

4

PS 3.25

safety precautions

• All accessories must be rated at or above the maximum operating pressure range of the sprayer. This includes spray tips, guns, extensions, and hose.

hAZArD: hIgh preSSure hoSe

The paint hose can develop leaks from wear, kinking and abuse. A leak can inject material into the skin. Inspect the hose before each use.

preveNTIoN:

•

•

•

•

Avoid sharp bending or kinking of the highpressure hose. The smallest bending radius amounts to about 20 cm.

Do not drive over the high-pressure hose.

Protect against sharp objects and edges.

Replace any damaged high-pressure hose immediately.

Never repair defective high-pressure hoses yourself!

•

•

Electrostatic charging of spray guns and the high-pressure hose is discharged through the high-pressure hose. For this reason the electric resistance between the connections of the high-pressure hose must be equal to or lower than 1MΩ.

For reasons of function, safety and durability use only original Wagner high-pressure hoses.

•

•

Before each use, check all hoses for cuts, leaks, abrasion or bulging of cover. Check for damage or movement of couplings.

Immediately replace the hose if any of these conditions exist. Never repair a paint hose. Replace it with another earthed highpressure hose.

Make sure power cord, air hose and spray hoses are routed in such a manner to minimize slip, trip and fall hazard.

5

safety precautions

PS 3.25

hAZArD: exploSIoN or fIre

Flammable vapors, such as solvent and paint vapors, in work area can ignite or explode. preveNTIoN:

• Do not use materials with a flashpoint below

38° C (100° F). Flashpoint is the temperature at which a fluid can produce enough vapors to ignite.

•

•

•

•

•

•

•

•

•

Do not use the unit in work places which are covered by the explosion protection regulations.

Provide extensive exhaust and fresh air introduction to keep the air within the spray area free from accumulation of flammable vapors.

Avoid all ignition sources such as static electricity sparks, electrical appliances, flames, pilot lights, hot objects, and sparks from connecting and disconnecting power cords or working light switches.

Do not smoke in spray area.

Place sprayer sufficient distance from the spray object in a well ventilated area (add more hose if necessary). Flammable vapors are often heavier than air. Floor area must be extremely well ventilated. The pump contains arcing parts that emit sparks and can ignite vapors.

The equipment and objects in and around the spray area must be properly grounded to prevent static sparks.

Use only conductive or earthed high pressure fluid hose. Gun must be earthed through hose connections.

Power cord must be connected to a grounded circuit (electric units only).

Always flush unit into separate metal container, at low pump pressure, with spray tip removed. Hold gun firmly against side of

6

•

•

•

• container to ground container and prevent static sparks.

Follow material and solvent manufacturer’s warnings and instructions. Be familiar with the coating material’s MSDS sheet and technical information to ensure safe use.

Use lowest possible pressure to flush equipment.

When cleaning the unit with solvents, the solvent should never be sprayed or pumped back into a container with a small opening

(bunghole). An explosive gas/air mixture can arise. The container must be earthed.

Do not use a paint or solvent containing halogenated hydrocarbons. Such as chlorine, bleach, mildewcide, methylene chloride and trichloroethane. They are not compatible with aluminum. Contact the coating supplier about compatibility of material with aluminum.

PS 3.25

safety precautions

hAZArD: hAZArDouS vAporS

Paints, solvents, and other materials can be harmful if inhaled or come in contact with body. Vapors can cause severe nausea, fainting, or poisoning.

hAZArD: geNerAl

This product can cause severe injury or property damage.

preveNTIoN:

• Wear respiratory protection when spraying.

Read all instructions supplied with the mask to be sure it will provide the necessary protection.

•

•

•

All local regulations regarding protection against hazardous vapors must be observed.

Wear protective eyewear.

Protective clothing, gloves and possibly skin protection cream are necessary for the protection of the skin. Observe the regulations of the manufacturer concerning coating materials, solvents and cleaning agents in preparation, processing and cleaning units.

preveNTIoN:

• Follow all appropriate local, state, and national codes governing ventilation, fire prevention, and operation.

• Pulling the trigger causes a recoil force to the hand that is holding the spray gun. The recoil force of the spray gun is particularly powerful when the tip has been removed and a high pressure has been set on the airless pump.

When cleaning without a spray tip, set the pressure control knob to the lowest pressure.

•

•

•

•

•

•

•

•

Use only manufacturer authorized parts.

User assumes all risks and liabilities when using parts that do not meet the minimum specifications and safety devices of the pump manufacturer.

ALWAYS follow the material manufacturer’s instructions for safe handling of paint and solvents.

Clean up all material and solvent spills immediately to prevent slip hazard.

Wear ear protection. This unit can produce noise levels above 85 dB(A).

Never leave this equipment unattended. Keep away from children or anyone not familiar with the operation of airless equipment.

Device weighs in excess of 18 kg. Two-person lift is required.

Do not spray on windy days.

The device and all related liquids (i.e. hydraulic oil) must be disposed of in an environmentally friendly way.

7

safety precautions

PS 3.25

1.2

elecTrIc SAfeTy

Electric models must be earthed. In the event of an electrical short circuit, earthing reduces the risk of electric shock by providing an escape wire for the electric current. This product is equipped with a cord having an earthing wire with an appropriate earthing plug. Connection to the mains only through a special feed point, e.g. through an error protection insallation with

INF < 30 mA.

DANGER — Work or repairs at the electrical equipment may only be carried out by a skilled electrician.

No liability is assumed for incorrect installation. Switch the unit off.

Before all repair work, unplug the power plug from the outlet.

1.3

elecTroSTATIc chArgINg

(formATIoN of SpArkS or flAmeS)

Electrostatic charging of the unit may occur during spraying due to the flow speed of the coating material. These can cause sparks and flames upon discharge. The unit must therefore always be earthed via the electrical system. The unit must be connected to an appropriately-grounded safety outlet.

Danger of short-circuits caused by water ingressing into the electrical equipment. Never spray down the unit with high-pressure or highpressure steam cleaners.

Work or repAIrS AT The elecTrIcAl equIpmeNT:

These may only be carried out by a skilled electrician. No liability is assumed for incorrect installation.

An electrostatic charging of spray guns and the high-pressure hose is discharged through the high-pressure hose. For this reason the electric resistance between the connections of the highpressure hose must be equal to or lower than 1

MΩ.

8

PS 3.25

2 geNerAl vIeW of ApplIcATIoN

2.1 ApplIcATIoN general view of application

= Recommended = Not-recommended model materials

Release agents, oils, undercoats, primers, fillers, synthetic resin-based paints, acrylic paints recommended nozzle size: FineFinish 0.008“ - 0.014“

Emulsion paints, latex paints recommended nozzle size: 0.017“ - 0.027“

Anti-corrosive agents, flame retardants, fabric adhesive recommended nozzle size: 0.021“ - 0.031“

Airless-scrapers recommended nozzle size: 0.027“ - 0.039“ object Size up to 200 m 2

200 m 2 - 800 m 2 more than 800 m 2 up to 200 m 2

200 m 2 - 800 m 2 more than 800 m 2 up to 200 m 2

200 m 2 - 800 m 2 more than 800 m 2 up to 200 m 2

200 m 2 - 800 m 2 more than 800 m 2

2.2 coATINg mATerIAlS proceSSIBle coATINg mATerIAlS i

Pay attention to the Airless quality of the coating materials to be processed.

Dilutable lacquers and paints or those containing solvents, twocomponent coating materials, dispersions, latex paints, release agents, oils, undercoats, primers, and fillers.

No other materials should be used for spraying without

Wagner’s approval.

fIlTerINg

Despite suction filter and insertion filter in the spray gun, filtering of the coating material is generally advisable.

Stir coating material before commencement of work.

i

Attention: Make sure, when stirring up with motor-driven agitators that no air bubbles are stirred in. Air bubbles disturb when spraying and can, in fact, lead to interruption of operation.

vIScoSITy

With this unit it is possible to process highly viscous coating materials of up to around 25.000 MPa·s.

If highly viscous coating materials cannot be taken in by suction, they must be diluted in accordance with the manufacturer’s instructions.

TWo-compoNeNT coATINg mATerIAl

The appropriate processing time must be adhered to exactly.

Within this time rinse through and clean the unit meticulously with the appropriate cleaning materials.

coATINg mATerIAlS WITh ShArp-eDgeD ADDITIoNAl mATerIAlS

These have a strong wear and tear effect on valves, highpressure hose, spray gun and tip. The durability of these parts cane be reduced appreciably through this.

9

description of unit

PS 3.25

3

DeScrIpTIoN of uNIT

3.1 AIrleSS proceSS

The main areas of application are thick layers of highly viscous coating material for large areas and a high consumption of material.

A piston pump takes in the coating material by suction and conveys it to the tip. Pressed through the tip at a pressure of up to a maximum of 221 bar (22.1 MPa), the coating material is atomised. This high pressure has the effect of micro fine atomisation of the coating material.

As no air is used in this process, it is described as an AIRLESS process.

This method of spraying has the advantages of finest atomisation, cloudless operation and a smooth, bubble-free surface. As well as these, the advantages of the speed of work and convenience must be mentioned.

3.2 fuNcTIoNINg of The uNIT

In the following there is a short description of the technical construction for better understanding of the function.

Wagner PS 3.25 units are electrically driven high-pressure spraying units.

A gear unit transfers the driving force to a crankshaft. The crankshaft moves the pistons of the material feed pump up and down.

The inlet valve is opened automatically by the upwards movement of the piston. The outlet valve is opened when the piston moves downward.

The coating material flows under high pressure through the high-pressure hose to the spray gun. When the coating material exits from the tip it atomizes.

The pressure control knob controls the volume and the operating pressure of the coating material.

3.3 TechNIcAl DATA voltage max. current consumption

100-110 Volt , 50/60 Hz

11 A power cord

3 x 1.5 mm

2

– 6 m

Acceptance capacity

1100 Watt max. operating pressure

221 bar (22.1 MPa)

volume flow at 12 mpa (120 bar) with water

2.6 l/min max tip size

0.027 inch – 0.69 mm max. temperature of the coating material

43°C max viscosity

25.000 MPa·s

Weight

Stand

Cart

Special high-pressure hose

17.9 kg

27.4 kg

DN 6 mm, 15 m, connection thread M 16 x 1.5

Dimensions (l x W x h)

Stand

Cart

Altitude

436 x 369 x 416 mm

611 x 481 x 734 mm

This equipment will operate correctly up to 2000 m above mean sea level vibration

Spray gun does not exceed 2.5m/s 2 max sound pressure level

80 dB*

* Place of measurement: 1 m distance from unit and

1.60m above floor, 12 MPa (120 bar) operating pressure, reverberant floor

10

PS 3.25

description of unit

3.4 legeND for explANATory DIAgrAm pS 3.25

1. Spray gun

2. High-pressure hose

3. Return hose

4. Suction hose

5. Frame

6. Drip cup

7. Power cord

8. Relief valve

Lever position vertical – PRIME ( k circulation)

Lever position horizontal – SPRAY ( p )

3.5 explANATory DIAgrAm pS 3.25

9. Oil button

10. Oil level gauge

11. ON/OFF switch

12. Control panel indicators

13. Pressure control knob

14. Digital Electronic Spray Control (DESC)

15. Oil cup for EasyGlide (EasyGlide prevents increased wear of the packings)

16. Pusher stem

17. Pail hook (high cart)

17

12 13 14

15

1

2

3

4

3

4

11 16

7

5

6

10

9

8

11

description of unit / starting operation

3.6 TrANSporTATIoN pushing or pulling the unit

Pull out the handle (Fig. 2, Item 1) until it will come no further.

Insert the handle – push the buttons (2) on the spars, and then push in the handle.

PS 3.25

4

STArTINg operATIoN

4.1 hIgh-preSSure hoSe, SprAy guN AND

SepArATINg oIl

1. Screw the high-pressure hose (2) to the coating material outlet (Fig. 3, Item 1).

2. Screw the spray gun (3) with the selected tip onto the high-pressure hose.

3. Tighten the union nuts at the high-pressure hoses firmly so that coating material does not leak.

1

2

2

3.7 TrANSporTATIoN IN vehIcle

Secure the unit with a suitable fastening. 2

1

3

4. Remove the oil cup cap with a straight-slot screwdriver.

5. Fill the oil cup with EasyGlide (Fig. 4) until the oil gauge (6) is showing that it is full.

EasyGlide prevents increased wear and tear to the packings.

Attention

6. Replace oil cup cap.

7. Press oil button 2-5 times to prime the oiler. Press once for every eight hours of usage to lubricate the fluid section.

8. Fully depress the pusher stem to make sure the inlet ball is free.

12

PS 3.25

starting operation

4.2 coNTrol pANel INDIcATorS

The following is a description of the control panel indicators.

Service

Indicator

6

Pressure

Indicator

ServIce INDIcATor

The Service indicator is on when the motor is commanded to run. This indicator is used by service centers to troubleshoot motor problems.

preSSure INDIcATor

The pressure indicator shows the current operating pressure of the sprayer. It has three different indications: blinking yellow, solid yellow, and solid green.

Blinking yellow

When the pressure indicator is blinking yellow, the sprayer is operating between 0 and 1.4 MPa (14 bar). A blinking yellow pressure indicator means:

• The sprayer is plugged in and turned “ON”

• The sprayer is at priming pressure (little or no pressure)

• It is safe to move the relief valve between positions

• It is safe to change or replace the spray tip i

If the pressure indicator begins blinking yellow when the pressure control knob is set at a higher pressure and the relief valve is in the SPRAY position, either the spray tip is worn or the sprayer is in need of service/repair.

Solid yellow

When the pressure indicator is solid yellow, the sprayer is operating between 1.4 MPa (14 bar) and 12 MPa (120 bar). A solid yellow pressure indicator means:

• The sprayer is at the proper pressure setting for spraying stain, lacquer, varnish, and multi-colors

Solid green

When the pressure indicator is solid green, the sprayer is operating between 12 MPa (120 bar) and 23 MPa (230 bar). A solid green pressure indicator means:

• The sprayer is at the proper pressure setting for spraying oil-based and latex house paints

• The sprayer is operating at peak performance at a high pressure setting

• If the pressure indicator goes to solid yellow when the pressure is set so that it starts at solid green, it indicates one of the following: a. Tip Wear Indicator — when spraying with latex or at high pressure the solid yellow appears. This means the tip is worn and needs to be replaced.

b. Tip Too large — when a tip that is too large for the sprayer is put in the gun, the pressure indicator will turn from solid green to solid yellow.

c. fluid Section Wear — if a solid yellow pressure indicator appears when using a new tip and the pressure is set at maximum, service may be required (worn packings, worn piston, stuck valve, etc...).

4.3 preSSure coNTrol kNoB SeTTINgS

1. Minimum pressure setting

2. Black zone – no pressure generation

3. Blue zone – pulsating pressure for cleaning

1

2

3

13

starting operation

PS 3.25

4.4 coNNecTIoN To The mAINS NeTWork

Attention

The unit must be connected to an appropriatelygrounded safety outlet.

Before connecting the unit to the mains supply, ensure that the line voltage matches that specified on the unit’s rating plate.

The connection must be equipped with a residual current protective device with INF ≤ 30 mA.

i

Wagner‘s accessories program also includes a mobile operator protection device for the electronic supply, which can also be used with other electronic equipment.

5 3

1

2

4

4.5 cleANINg preServINg AgeNT WheN

STArTINg-up of operATIoN INITIAlly

1. Immerse the suction tube (Fig. 7, Item 2) return hose (1) into a container with a suitable cleaning agent.

2. Turn the pressure control knob counterclockwise (3) to minimum pressure.

3. Open the relief valve (4), valve position PRIME ( k circulation).

4. Switch the unit (5) ON.

5. Wait until the cleaning agent exudes from the return hose.

6. Close the relief valve, valve position SPRAY ( p spray).

7. Pull the trigger of the spray gun.

8. Spray the cleaning agent from the unit into an open collecting container.

4.6 TAkINg The uNIT INTo operATIoN WITh coATINg mATerIAl

1. Immerse the suction tube (Fig. 7, Item 2) and return hose

(1) into the coating material container.

2. Turn the pressure control knob counterclockwise (3) to minimum pressure.

3. Open the relief valve (4), valve position PRIME ( k circulation).

4. Switch the unit (5) ON.

5. Wait until the coating material exudes from the return hose.

6. Close the relief valve, valve position SPRAY ( p spray).

7. Trigger the spray gun several times and spray into a collecting container until the coating material exits the spray gun without interruption.

8. Increase the pressure by slowly turning up the pressure control knob.

Check the spray pattern and increase the pressure until the atomization is correct.

Always turn the pressure control knob to the lowest setting with good atomization.

9. The unit is ready to spray.

14

PS 3.25

starting operation

4.7 DIgITAl elecTroNIc SprAy coNTrol

(DeSc) i

The Digital Electronic Spray Control (DESC) increases the functionality of the sprayer. It is installed directly below the pressure control knob on the control panel. It consists of a display and four function keys. The display shows various menu screens that allow the user to customize and monitor sprayer operation using the function keys.

mAIN ScreeN

The Main Screen is the default screen for the control system at sprayer startup. pressing the #2 key switches between pSI, BAr and mpa units of

measure. Press the #1 key to scroll through the remaining menu screens.

i

For sprayers equipped with an nine-language

Digital Electronic Spray Control (DESC):

Pressing the #2 key at the Main Screen switches between PSI, Bar and MPa units of measure.

i

Display

Function

Keys volume pumpeD ScreeN

The Volume Pumped screen shows the total number of gallons or liters sprayed by the sprayer.

To select the Volume Pumped screen, press the #4 key.

MENU-1

MENU-1

LITRES-2

GALLONS-2

The pressure control knob overrides the Digital

Electronic Spray Control (DESC) settings.

Anytime the pressure control knob is turned, the sprayer pressure will change accordingly.

fuNcTIoN keyS

The function keys are numbered 1–4. Each key is labeled with an additional function as well.

#1/menu key Pressing the #1 key scrolls through the available menu screens or performs a function described on the active menu screen.

#2/ p key Pressing the #2 key performs a function described on the active menu screen or increases a value.

#3/ q key Pressing the #3 key performs a function described on the active menu screen or decrease a value.

#4/Select key Pressing the #4 key selects the active menu screen or performs a function described on the active menu screen.

meNu ScreeNS

Several menu screens are available for the user to customize and monitor sprayer operation. They include Main Screen,

Volume Pumped, Job Volume, Unit Serial #, Timers, Job Timers,

Service Time, Security Code, Prime, and Rapid Clean.

joB volume ScreeN

The Job Volume screen allows the user to reset a liter counter to track usage on specific jobs.

To select the Job Volume screen, press the #4 key.

JOB VOLUME

MENU-1 SELECT-4 uNIT SerIAl # ScreeN

The Unit Serial # screen shows the sprayers serial number.

To select the Unit Serial # screen, press the #4 key.

UNIT SERIAL #

MENU-1 SELECT-4

TImerS ScreeN

The Timers screen shows the total time the sprayer has been turned on as well as the total time the sprayer has been running (pumping).

To select the Timers screen, press the #4 key.

MENU-1

15

starting operation

PS 3.25

joB TImerS ScreeN

The Job Timers screen allows the user to reset the “ON TIME” and “RUN

TIME” to track time on specific jobs.

To select the Job Timers screen, press the #4 key. “JOB ON” screen will appear. Press #3 to reset. Press

#1 to continue to “JOB RUN” screen.

Press #3 to reset. Press #1 to scroll through the remaining menu screens.

ServIce TIme ScreeN

The Service Time screen allows the user to set a service time interval

(in hours). Below the set time, the screens shows the current amount of hours on the sprayer since the last activation of the service timer. To select the Service

Timer screen, press the #4 key.

To set the service time, press the #2

(up) and/or the #3 (down) keys to the desired time (run hours will increase/ decrease in increments of 25 for each time you press a key).

When the sprayer reaches the SERVICE@ time selected, the screen will display “SERVICE DUE”. To reset the timer, press the #3 key when the pump is first turned on. This will reset the

“SERVICE DUE” message and also reset the “SERVICE TIME” to the previous setting.

SecurITy coDe ScreeN

The Security Code screen allows the user to set a four digit security code to prevent unauthorized use of the sprayer. If a security code has been set, the control system display will ask for the code at startup. If the correct code is entered, the display will show the Main Screen and the sprayer will operate. If the wrong code is entered, the display will continue to ask for the correct code and the sprayer will not work. To set or change the security code, press the #2 key.

i

If the sprayer is new, no security code is set and the Main Screen will appear at startup. When setting a security code for the first time, the

“Enter Old Code Number” screen will appear, and you will need to enter “1111”.

Enter the old security code number to access the screen that allows the code change. If the wrong code is entered, the display will continue to ask for the correct code and the security code cannot be changed.

Enter the new security code. Once the new code is entered, the display will automatically ask that the new code be re-entered for verification.

If the same new code is re-entered, the display will confirm that the new code has been accepted and return to the Main Screen. If the new code is re-entered incorrectly, the display will return to the

“Enter New Code Number” screen and the process will repeat.

If you forget or misplace your security code, you can contact

Wagner customer service for assistance.

i

To inactivate the security function, enter “1111” at the “Enter New Code Number” screen (this is the default code that leaves the sprayer unlocked).

As a result, the Main Screen will appear at sprayer startup.

prIme ScreeN

The Prime screen appears when the pressure control knob is set at the

“MIN” setting.

PRIME rApID cleAN ScreeN

The Rapid Clean screen appears when the pressure control knob is

RAPID CLEAN set at the RAPID CLEAN position and the PRIME/SPRAY valve is in the PRIME position.

i

If there is no action at any menu screen for 30 seconds, the display will go back to the Main

Screen.

16

5

SprAyINg

Injection hazard. Do not spray without the tip guard in place. NEVER trigger the gun unless the tip is completely turned to either the spray or the unclog position. ALWAYS engage the gun trigger lock before removing, replacing or cleaning tip.

A) The key to a good paint job is an even coating over the entire surface. Keep your arm moving at a constant speed and keep the spray gun at a constant distance from the surface. The best spraying distance is 10-12 inches

(25 to 30 cm) between the spray tip and the surface.

A

25 - 30 cm c

25 - 30 cm 25 - 30 cm i

If very sharp edges result or if there are streaks in the spray jet – increase the operating pressure or dilute the coating material.

B) Keep the spray gun at right angles to the surface. This means moving your entire arm back and forth rather than just flexing your wrist.

Keep the spray gun perpendicular to the surface, otherwise one end of the pattern will be thicker than the other.

B

c) Trigger gun after starting the stroke. Release the trigger before ending the stroke. The spray gun should be moving when the trigger is pulled and released. Overlap each stroke by about 30%. This will ensure an even coating.

17

handling the high -pressure hose / interruption of work

6 hANDlINg The hIgh-preSSure hoSe i

The unit is equipped with a high-pressure hose specially suited for piston pumps.

Danger of injury through leaking high-pressure hose. Replace any damaged high-pressure hose immediately.

Never repair defective high-pressure hoses yourself!

The high-pressure hose is to be handled with care. Avoid sharp bends and folds: the smallest bending radius is about 8” (20 cm).

Do not drive over the high-pressure hose. Protect against sharp objects and edges.

Never pull on the high-pressure hose to move the device.

Make sure that the high-pressure hose cannot twist. This can be avoided by using a Wagner spray gun with a swivel joint and a hose system.

i i i

When using the high-pressure hose while working on scaffolding, it is best to always guide the hose along the outside of the scaffolding.

The risk of damage rises with the age of the highpressure hose. Wagner recommends replacing high-pressure hoses after 6 years.

Use only Wagner original-high-pressure hoses in order to ensure functionality, safety and durability.

PS 3.25

7

INTerrupTIoN of Work

1. Open the relief valve, valve position PRIME ( k circulation).

2. Switch the unit OFF.

3. Turn the pressure control knob counterclockwise to minimum pressure.

4. Pull the trigger of the spray gun in order to release the pressure from the high-pressure hose and spray gun.

5. Secure the spray gun, refer to the operating manual of the spray gun.

6. If a standard tip is to be cleaned, see Page 26, Section 12.2.

If a non-standard tip is installed, proceed according to the relevant operating manual.

7. Depending on the model, leave the suction tube or the suction hose and return hose immersed in the coating material or swivel or immerse it into a corresponding cleaning agent.

Attention

If fast-drying or two-component coating material is used, ensure that the unit is rinsed with a suitable cleaning agent within the processing time.

18

PS 3.25

8 cleANINg The uNIT (ShuTTINg

DoWN) i i i

A clean state is the best method of ensuring operation without problems. After you have finished spraying, clean the unit. Under no circumstances may any remaining coating material dry and harden in the unit.

The cleaning agent used for cleaning (only with an igni tion point above 38 °C) must be suitable for the coating material used.

• Secure the spray gun, refer to the operating manual of the spray gun.

• Clean and remove tip.

• For a standard tip, refer to Page 26, Section

12.2.

• If a non-standard tip is installed, proceed according to the relevant operating manual.

1. Remove suction hose from the coating material.

2. Close the relief valve, valve position SPRAY ( p spray).

3. Switch the unit ON.

The container must be earthed in case of coating materials which contain solvents.

Attention

Caution! Do not pump or spray into a container with a small opening (bunghole)!

cleaning the unit (shutting down)

8.1 cleANINg uNIT from ouTSIDe

First of all pull out mains plug from socket.

Attention

Danger of short circult through penetrating water!

Never spray down the unit with high-pressure or high-pressure steam cleaners.

Do not put the high-pressure hose into solvents.

Use only a wet cloth to wipe down the outside of the hose.

Wipe down unit externally with a cloth which has been immersed in a suitable cleaning agent.

8.2 SucTIoN fIlTer i

A clean suction filter always guarantees maximum feed quantity, constant spraying pressure and problem-free functioning of the unit.

1. Screw off the filter (Fig. 8) from suction tube.

2. Clean or replace the filter.

Carry out cleaning with a hard brush and an appropriate cleaning agent.

4. Pull the trigger of the spray gun in order to pump the remaining coating material from the suction hose, highpressure hose and the spray gun into an open container.

5. Immerse suction hose with return hose into a container with a suitable cleaning agent.

6. Turn the pressure control knob counterclockwise to minimum pressure.

7. Open the relief valve, valve position PRIME ( k circulation).

8. Pump a suitable cleaning agent in the circuit for a few minutes.

9. Close the relief valve, valve position SPRAY ( p spray).

10. Pull the trigger of the spray gun.

11. Pump the remaining cleaning agent into an open container until the unit is empty.

12. Switch the unit OFF.

19

cleaning the unit (shutting down)

PS 3.25

8.3 cleANINg The hIgh-preSSure fIlTer 8.4 cleANINg AIrleSS SprAy guN i

Clean the filter cartridge regularly. A soiled or clogged high-pressure filter can cause a poor spray pattern or a clogged tip. i

Clean the spray gun after each use.

1. Turn the pressure control knob counterclockwise to minimum pressure.

2. Open the relief valve, valve position PRIME ( k circulation).

3. Switch the unit OFF.

Unplug the power plug from the outlet.

4. Unscrew the filter housing (Fig. 9, Item 1) with a strap wrench.

5. Turning clockwise, unscrew the filter (2) from the pump manifold (3).

6. Clean all the parts with the corresponding cleaning agent.

If necessary, replace the filter cartridge.

7. Check the O-ring (4), replace it if necessary.

8. Turning counterclockwise, screw the new or cleaned filter into the pump manifold.

9. Screw in filter housing (1) and tighten it as far as possible with the strap wrench.

4

3

5

2

1. Rinse airless spray gun with an appropriate cleaning agent.

2. Clean tip thoroughly with appropriate cleaning agent so that no coating material residue remains.

3. Thoroughly clean the outside of the airless spray gun.

INTAke fIlTer IN AIrleSS SprAy guN (fIg. 10)

1. Unclip the top of the trigger guard (1) from the gun head.

2. Using the bottom of the trigger guard as a wrench, loosen and remove the handle assembly (2) from the gun head.

3. Pull the old filter (3) out of the gun head. Clean or replace.

4. Slide the new filter, tapered end first, into the gun head.

5. Thread the handle assembly into the gun head. Tighten with the trigger wrench.

6. Snap the trigger guard back onto the gun head.

1

3

2

1

20

PS 3.25

9 remeDy IN cASe of fAulTS remedy in case of faults

Type of malfunction

A. Unit does not start

B. Unit does not draw in material possible cause

1. No voltage applied.

2. Pressure setting too low.

3. ON/OFF switch defective.

measures for eliminating the malfunction

1. Check voltage supply.

2. Turn up pressure control knob.

3. Replace.

1. Relief valve is set to SPRAY ( p spray).

2. Filter projects over the fluid level and sucks air.

3. Filter clogged.

4. Suction hose/suction tube is loose, i.e. the unit is sucking in outside air.

1. Set relief valve to PRIME ( k circulation).

2. Refill the coating material.

3. Clean or replace the filter.

4. Clean connecting points. Replace O-rings if necessary.

Secure suction hose with retaining clip.

C. Unit draws in material, but the pressure does not build up

1. Tip heavily worn.

2. Tip too large.

3. Pressure setting too low.

4. Filter clogged.

5. Coating material flows through the return hose when the relief valve is in the SPRAY ( p spray) position.

6. Packings sticky or worn.

7. Valve balls worn.

8. Valve seats worn.

1. Replace

2. Replace tip.

3. Turn pressure control knob clockwise to increase.

4. Clean or replace the filter.

5. Remove and clean or replace relief valve.

6. Remove and clean or replace packings.

7. Remove and replace valve balls.

8. Remove and replace valve seats.

D. Coating material exits at the top of the fluid section

E. Increased pulsation at the spray gun

1. Upper packing is worn.

2. Piston is worn.

1. Incorrect high-pressure hose type.

2. Tip worn or too large.

3. Pressure too high.

F. Poor spray pattern

1. Remove and replace packing.

2. Remove and replace piston.

1. Only use WAGNER original-high-pressure hoses in order to ensure functionality, safety and durability.

2. Replace tip.

3. Turn pressure control knob to a lower number.

G. Unit loses power

1. Tip is too large for the coating material which is to be sprayed.

2. Pressure setting incorrect.

3. Volume too low.

4. Coating material viscosity too high.

1. Pressure setting too low.

1. Replace tip.

2. Turn pressure control knob until a satisfactory spraying pattern is achieved.

3. Clean or replace all filters.

4. Thin out according to the manufacturer’s instructions.

1. Turn pressure control knob clockwise to increase.

H. Pump over-pressurizes and will not shut off.

1. Pressure switch defective.

2. Transducer defective.

1. Take unit to a Wagner authorized service center.

2. Take unit to a Wagner authorized service center.

21

servicing / repairs at the unit

PS 3.25

10

ServIcINg

10.1 geNerAl ServIcINg

Servicing of the unit should be carried out once annually by the

WAGNER service.

1. Check high-pressure hoses, device connecting line and plug for damage.

2. Check the inlet valve, outlet valve and filter for wear.

i

11 i repAIrS AT The uNIT

Switch the unit OFF.

Before all repair work: Unplug the power plug from the outlet.

Make sure to check for grounding continuity after service is performed on any electrical components.

Use an ohmmeter to determine that there is continuity between accessible dead-metal parts of the product and the grounding blade of the attachment plug.

10.2 hIgh-preSSure hoSe

Inspect the high-pressure hose visually for any notches or bulges, in particular at the transition in the fittings. It must be possible to turn the union nuts freely.

The risk of damage rises with the age of the highpressure hose. Wagner recommends replacing high-pressure hoses after 6 years.

11.1 relIef vAlve

Attention

The valve housing (4) should not be repaired. If worn, it should always be replaced with a new one.

1. Use a drift punch of 2 mm to remove the grooved pin (Fig.

10, Item 1) from the relief valve handle (2).

2. Remove the relief valve handle (2) and cam base (3).

3. Using a wrench, remove the valve housing (4) from the pump manifold (6).

4. Ensure that the seal (5) is seated correctly, then screw the new valve housing (4) completely into the pump manifold

(6). Tighten securely with a wrench.

5. Align the cam base (3) with the hole in the pump manifold

(6). Lubricate the cam base with grease and slide on the cam base.

6. Bring the hole in the valve shaft (7) and in the relief valve handle (2) into alignment.

7. Insert the grooved pin (1) to secure the relief valve handle in position.

6

5

7

3

4

2

1

22

PS 3.25

repairs at the unit

11.2 INleT AND ouTleT vAlve

1. Remove the four screws in the front cover and then remove the front cover.

Danger of crushing - do not reach with the fingers or tool between the moving parts.

11

10

12

13

2

3

4

5

6

1 2. The piston rod will need to be in the lower stroke position: a. Turn the pressure control knob to minimum pressure. The

DESC screen should say “PRIME”.

b. Press the #1 key on the DESC control panel. The “CREEP

MODE” screen will now appear.

c. Slowly turn the pressure control knob clockwise to increase the pressure. The crankshaft/slider assembly will begin to move very slowly.

d. When it reaches the bottom, dead-center of its stroke, turn the pressure control knob back to minimum pressure. The crankshaft/slider assembly should stop.

3. Unplug the power plug from the outlet.

4. unit on high-rider cart:

Screw off the suction tube.

unit on stand:

Remove the retaining clip from the connecting bend at the suction hose and pull off the suction hose.

5. Screw off the return hose.

6. Swivel the unit 90° to the rear in order to work more easily on the material feed pump.

7. Remove the pusher stem clip and slide the pusher stem housing (7) from the inlet valve housing (1).

8. Unscrew the inlet valve housing (Fig. 11, Item 1) from the pump manifold.

9. Remove the lower seal (2), lower ball guide (3), inlet valve ball (4), inlet valve seat (5) and O-ring (6).

10. Clean all the parts with the corresponding cleaning agent.

Check the inlet valve housing (1), inlet valve seat (5) and inlet valve ball (4) for wear and replace the parts if necessary. If the worn inlet valve seat (5) is unused on one side, install it the other way round.

7

11. Unscrew outlet valve housing (Fig. 12, Item 8) from the piston (9) with adjusting wrench.

12. Remove the upper ball cage (11), crush washer (10), outlet valve ball (12), and outlet valve seat (13).

13. Clean all the parts with the corresponding cleaning agent.

Check outlet valve housing (8), outlet valve seat (13), outlet valve ball (12), crush washer (10), and upper ball cage (11) for wear and replace parts if necessary. If the worn outlet valve seat (13) is unused on one side, install it the other way round.

14. Carry out installation in the reverse order. Lubricate O-ring

(Fig. 11, Item 6) with machine grease and ensure proper seating in the inlet valve housing (Fig. 11, Item 1).

9

8

23

repairs at the unit

PS 3.25

11.3 pAckINgS

1. Remove inlet valve housing in accordance with the steps in Chapter 11.2, Page 23.

2. It is not necessary to remove the outlet valve.

3. Unscrew both cylinder head screws (Fig. 13, Item 1) from the pump manifold (2) with a 3/8 inch hexagon socket head wrench.

4. Slide the pump manifold (2) and piston (3) forward until the piston is out of the T-slot (9) on the slider assembly (4).

5. Push piston (3) downward out of the pump manifold (2).

6. Unscrew retainer nut (5) from the pump manifold (2) and remove piston guide (6).

7. Remove upper packing (7) and lower packing (8) from the pump manifold (2).

9

4

5

6

7

2

1

8

3

8. Clean pump manifold (2).

9. Lubricate upper packing (7) and lower packing (8) with machine grease.

10. Insert upper packing (Fig. 14) with O-ring (1) and protruding lip (2) downward.

11. Insert lower packing (Fig. 15) with the beveled edge (1) facing upward.

1

12. Insert piston guide (Fig. 13, Item 6) into the retainer nut

(5). Screw retainer nut (5) into the pump manifold (2) and tighten by hand.

13. Push installation tool (included with the replacement packings) for the piston (3) from above onto the piston.

14. Lubricate installation tool and piston (3) with machine grease.

15. Guide piston (3) through the lower packings (8) into the pump manifold (2) from below. Using a rubber mallet, lightly tap the piston (3) from below until it can be seen above the pump manifold.

16. Remove installation tool from piston (3).

17. Carefully tighten retainer nut (5) with adjusting wrench.

18. Slide the top of the piston (3) into the T-slot (9) on the slider assembly (4).

19. Position the pump manifold (2) underneath the gear unit housing and push up until it rests against the gear unit housing.

20. Attach pump manifold (2) to the gear unit housing.

21. Screw pump manifold (2) tightly to gear unit housing.

22. Lubricate O-ring (Fig. 11, Item 6) between pump manifold

(2) and inlet valve housing with machine grease. Screw inlet valve housing to the pump manifold.

23. unit on high-rider cart:

Thread the siphon tube into the inlet valve and tighten securely. Make sure to wrap the threads on the down tube with PTFE tape before assembly. Replace the return hose into the hose clip on the siphon tube.

u nit on stand:

Insert the elbow on the siphon assembly into the bottom of the pusher stem housing. Push the retaining clip up into the groove inside the foot valve housing to secure the siphon assembly in position. Place the return tube over the return tube fitting and secure with the clip.

24. Install front cover.

1

2

24

PS 3.25

11.4 pS 3.25 coNNecTIoN DIAgrAm

White or Blue

EMI Filter repairs at the unit

Power Cord

Capacitor

Switch

Black

Ground

P/N 0522054

Ground

Black

Fuse block

Fuse

Black

Black

Red

Motor controller

Red (+)

Black (-)

White

Surge suppressor

P/N 0551972

White

White

Red

Black

Motor

L.E.D.

Hall sensor

Potentiometer

Display wire assembly

(P/N 0522022)

Pressure sensor

11.5 DIgITAl elecTroNIc SprAy coNTrol

(DeSc) error meSSAgeS

The following error message screens appear whenever the Digital Electronic

Spray Control (DESC) detects a problem with the sprayer. Once a problem occurs and the error message appears, the sprayer will shut down.

Before proceeding, relieve any pressure remaining in the system (valve position PRIME k ). Additionally, follow all other warnings to reduce the risk of an injection injury, injury from moving parts or electric shock. Always unplug the sprayer before servicing!

check TrANSDucer ScreeN

The Check Transducer screen appears when the transducer has become disconnected or is

CHECK

TRANSDUCER defective. Take the sprayer to a Wagner authorized service center for repair.

check poTeNTIomeTer ScreeN

The Check Potentiometer screen appears when the potentiometer has become disconnected or is defective. Take the sprayer to a Wagner authorized service center for repair.

check moTor ScreeN

Indicates the motor is shut down due to connection problems between the motor and controller. Take the sprayer to a Wagner authorized service center for repair.

CHECK

MOTOR loW volTAge ScreeN

The Low Voltage screen appears when the sprayer shuts down because of low input voltage. Check the power supply and correct the problem. Restart the sprayer.

hIgh moTor TemperATure ScreeN

The High Motor Temperature screen appears when the temperature of the motor has risen too high. Take the sprayer to a Wagner authorized service center for repair.

hIgh mechANIcAl loAD

The High Mechanical Load screen appears when the sprayer shuts down because of high current or when the sprayer goes into current fold back mode. Take the sprayer to a

Wagner authorized service center for repair.

hIgh coNTrol TemperATure ScreeN

Indicates the DESC is shut down due to excessive heat. Take the sprayer to a Wagner authorized service center for repair.

BAD hAll cycle poWer ScreeN

Indicates the motor or motor hall affect sensors are defective. Take the sprayer to a Wagner authorized service center for repair.

25

appendix

PS 3.25

12

AppeNDIx

12.1 SelecTIoN of TIp

To achieve faultless and rational working, the selection of the tip is of the greatest importance.

In many cases the correct tip can only be determined by means of a spraying test.

Some ruleS for ThIS:

The spray jet must be even.

If streaks appear in the spray jet the spraying pressure is either too low or the viscosity of the coating material to high.

remeDy: Increase pressure or dilute coating material. Each pump conveys a certain quantity in proportion to the size of the tip:

The following principle is valid: large tip = low pressure small tip = high pressure

There is a large range of tips with various spraying angles.

12.2 ServIcINg AND cleANINg of AIrleSS hArD-meTAl TIpS

STANDArD TIpS

If a different tip type has been fitted, then clean it according to manufacturer’s instructions.

The tip has a bore processed with the greatest precision. Careful handling is necessary to achieve long durability. Do not forget the fact that the hard-metal insert is brittle! Never throw the tip or handle with sharp metal objects.

The following points must be observed to keep the tip clean and ready for use:

1. Turn the relief valve handle fully counterclockwise ( k

Circulation).

2. Remove the tip from the spray gun.

3. Place tip in an appropriate cleaning agent until all coating material residue is dissolved.

4. If there is high-pressure air available, blow out tip.

5. Remove any residue by means of a sharp wooden rod

(toothpick).

6. Check the tip with the help of a magnifying glass and, if necessary, repeat points 3 to 5.

26

12.3 SprAy guN AcceSSorIeS flat jet adjusting tip up to 250 bar (25 MPa

Tip marking

15

20

28

41

49

Bore mm

0.13 - 0.46

0.18 - 0.48

0.28 - 0.66

0.43 - 0.88

0.53 - 1.37

Spray width at about 30 cm removal of spray object pressure 100 bar (10 mpa)

5 - 35 cm

5 - 50 cm

8 - 55 cm

10 - 60 cm

10 - 40 cm use

Paints

Paints, fillers

Paints, dispersions

Rust protection paints - dispersions

Large-area coats flat jet adjusting tip order No.

0999 057

0999 053

0999 054

0999 055

0999 056 contact protection for the flat jet adjustment tip

Order No. 0097 294

Tip extension with slewable knee joint

(without tip)

Tip extension

Length: 100 cm

Length: 200 cm

Length: 300 cm

Order no. 0096 015

Order no. 0096 016

Order no. 0096 017

15 cm, F-thread, Order no. 0556 051

30 cm, F-thread, Order no. 0556 052

45 cm, F-thread, Order no. 0556 053

60 cm, F-thread, Order no. 0556 054

15 cm, G-thread, Order no. 0556 074

30 cm, G-thread, Order no. 0556 075

45 cm, G-thread, Order no. 0556 076

60 cm, G-thread, Order no. 0556 077

27

appendix

12.4 AIrleSS TIp TABle

Wagner

TradeTip 3 tip up to 270 bar

(27 MPa) without tip

F thread (11/16 - 16 UN) for Wagner spray guns order no. 0289391 without tip

G thread (7/8 - 14 UN) for Graco/Titan spray guns order no. 0289390 i

All of the tips in the table below are supplied together with the appropriate gun filter.

PS 3.25

Application Tip marking

Water-thinnable and solvent-based paints and varnishes, oils, separating agents

Synthetic-resin paints pvc paints paints, primers fillers fillers rust protection paints rust protection paints latex paints

Dispersions rust protection paints latex paints

Dispersions

117

217

317

417

517

617

717

817

115

215

315

415

515

615

715

815

219

319

419

519

619

719

819

919

111

211

311

411

511

611

107

207

307

407

109

209

309

409

509

609

113

213

313

413

513

613

813

100

120

150

190

225

270

300

330

100

120

150

190

225

270

300

330

120

150

190

225

270

300

330

385

100

120

150

190

225

270

330

100

120

150

190

225

270

Spraying width mm 1)

100

120

150

190

100

120

150

190

225

270

0.015 / 0.38

0.015 / 0.38

0.015 / 0.38

0.015 / 0.38

0.015 / 0.38

0.015 / 0.38

0.015 / 0.38

0.015 / 0.38

0.017 / 0.43

0.017 / 0.43

0.017 / 0.43

0.017 / 0.43

0.017 / 0.43

0.017 / 0.43

0.017 / 0.43

0.017 / 0.43

0.019 / 0.48

0.019 / 0.48

0.019 / 0.48

0.019 / 0.48

0.019 / 0.48

0.019 / 0.48

0.019 / 0.48

0.019 / 0.48

Bore inch / mm

0.007 / 0.18

0.007 / 0.18

0.007 / 0.18

0.007 / 0.18

0.009 / 0.23

0.009 / 0.23

0.009 / 0.23

0.009 / 0.23

0.009 / 0.23

0.009 / 0.23

0.011 / 0.28

0.011 / 0.28

0.011 / 0.28

0.011 / 0.28

0.011 / 0.28

0.011 / 0.28

0.013 / 0.33

0.013 / 0.33

0.013 / 0.33

0.013 / 0.33

0.013 / 0.33

0.013 / 0.33

0.013 / 0.33

10°

20°

30°

40°

50°

60°

70°

80°

10°

20°

30°

40°

50°

60°

70°

80°

20°

30°

40°

50°

60°

70°

80°

90°

10°

20°

30°

40°

50°

60°

80°

10°

20°

30°

40°

50°

60°

Spray angle

10°

20°

30°

40°

10°

20°

30°

40°

50°

60° gun filter yellow yellow yellow yellow yellow yellow yellow yellow white white white white white white white white white white white white white white white white red red red red red red red red red red red red red red red red red red red red red red red order no.

0553115

0553215

0553315

0553415

0553515

0553615

0553715

0553815

0553117

0553217

0553317

0553417

0553517

0553617

0553717

0553817

0553219

0553319

0553419

0553519

0553619

0553719

0553819

0553919

0553107

0553207

0553307

0553407

0553109

0553209

0553309

0553409

0553509

0553609

0553111

0553211

0553311

0553411

0553511

0553611

0553113

0553213

0553313

0553413

0553513

0553613

0553813

1)Spray width at about 30 cm to the object and 100 bar (10 MPa) pressure with synthetic-resin paint 20 DIN seconds.

28

Application flame retardant roof coatings

Thick-film materials, corrosion protection

Spray filler heavy duty applications

Tip marking

20°

30°

40°

50°

60°

70°

80°

Spray angle

20°

30°

40°

50°

60°

70°

80°

50°

60°

20°

40°

50°

60°

20°

40°

20°

40°

50°

60°

40°

50°

60°

40°

50°

60°

20°

40°

50°

60°

20°

40°

80°

20°

30°

40°

50°

60°

20°

30°

50°

60°

20°

30°

40°

50°

60°

70°

40°

50°

60°

70°

40°

50°

60°

30°

40°

50°

60°

80°

20°

30°

40°

20°

30°

40°

50°

60°

70°

80°

20°

551

651

252

455

555

655

261

461

243

443

543

643

445

545

645

451

561

661

263

463

565

665

267

467

831

233

333

433

533

633

235

335

529

629

231

331

431

531

631

731

435

535

635

735

439

539

639

327

427

527

627

827

229

329

429

225

325

425

525

625

725

825

227

223

323

423

523

623

723

823

221

321

421

521

621

721

821 gun filter white white white white white white white white white white white white white white white white white white white white white white white white white white white white white white white white white white white white white white white white white white white white white white white white white white white white white green green green green green green green green green green green green green green green green green green green green green green green green

225

270

120

190

225

270

120

190

120

190

225

270

190

225

270

190

225

270

120

190

225

270

120

190

330

120

150

190

225

270

120

150

225

270

120

150

190

225

270

300

190

225

270

300

190

225

270

150

190

225

270

330

120

150

190

120

150

190

225

270

300

330

120

120

150

190

225

270

300

330

Spraying width mm 1)

120

150

190

225

270

300

330

Bore inch / mm

0.021 / 0.53

0.021 / 0.53

0.021 / 0.53

0.021 / 0.53

0.021 / 0.53

0.021 / 0.53

0.021 / 0.53

0.023 / 0.58

0.023 / 0.58

0.023 / 0.58

0.023 / 0.58

0.023 / 0.58

0.023 / 0.58

0.023 / 0.58

0.043 / 1.10

0.043 / 1.10

0.043 / 1.10

0.043 / 1.10

0.045 / 1.14

0.045 / 1.14

0.045 / 1.14

0.051 / 1.30

0.051 / 1.30

0.051 / 1.30

0.052 / 1.32

0.055 / 1.40

0.055 / 1.40

0.055 / 1.40

0.061 / 1.55

0.061 / 1.55

0.061 / 1.55

0.061 / 1.55

0.063 / 1.60

0.063 / 1.60

0.065 / 1.65

0.065 / 1.65

0.067 / 1.70

0.067 / 1.70

0.025 / 0.64

0.025 / 0.64

0.025 / 0.64

0.025 / 0.64

0.025 / 0.64

0.025 / 0.64

0.025 / 0.64

0.027 / 0.69

0.027 / 0.69

0.027 / 0.69

0.027 / 0.69

0.027 / 0.69

0.027 / 0.69

0.029 / 0.75

0.029 / 0.75

0.029 / 0.75

0.029 / 0.75

0.029 / 0.75

0.031 / 0.79

0.031 / 0.79

0.031 / 0.79

0.031 / 0.79

0.031 / 0.79

0.031 / 0.79

0.031 / 0.79

0.033 / 0.83

0.033 / 0.83

0.033 / 0.83

0.033 / 0.83

0.033 / 0.83

0.035 / 0.90

0.035 / 0.90

0.035 / 0.90

0.035 / 0.90

0.035 / 0.90

0.035 / 0.90

0.039 / 0.99

0.039 / 0.99

0.039 / 0.99

order no.

0553221

0553321

0553421

0553521

0553621

0553721

0553821

0553223

0553323

0553423

0553523

0553623

0553723

0553823

0553529

0553629

0553231

0553331

0553431

0553531

0553631

0553731

0553831

0553233

0553333

0553433

0553533

0553633

0553235

0553335

0553225

0553325

0553425

0553525

0553625

0553725

0553825

0553227

0553327

0553427

0553527

0553627

0553827

0553229

0553329

0553429

0553435

0553535

0553635

0553735

0553439

0553539

0553639

0553243

0553443

0553543

0553643

0553445

0553545

0553645

0553451

0553551

0553651

0553252

0553455

0553555

0553655

0553261

0553461

0553561

0553661

0553263

0553463

0553565

0553665

0553267

0553467

1)Spray width at about 30 cm to the object and 100 bar (10 MPa) pressure with synthetic-resin paint 20 DIN seconds.

29

appendix

PS 3.25

12.5 TempSprAy

The paint material is heated to the required temperature uniformly by an electric heating element, which is located inside the hose

(regulated from 20°C to 60°C).

Advantages:

• Constant paint temperature even at low outside temperatures

• Considerably better working of high viscosity coating materials

• Increased application efficiency

• Savings in solvents due to reduction in viscosity

• Adaptable to all airless units order No.

Description

TempSpray h 126 (ideal for lacquer jobs)

2311659

Basic unit 1/4“ incl. stainless steel hose, DN6, 1/4“, 10m

2311852

Spraypack consisting of: basic unit (2311659), Airless gun AG 14 NPS 1/4“, incl. Trade Tip 2 nozzler holder

(F-thread) and Trade Tip 2 Fine Finish 410

2311660

2311853

TempSpray h 226 (ideal for dispersions/materials with high viscosity)

Basic unit 1/4“ incl. Hose reel, heated hose DN10, 15m, hose 1/4“ DN4, 1m

Spraypack consisting of: Basic unit (2311660), Airless gun AG 14 NPS 1/4“, incl. Trade Tip 2 nozzler holder

(F-thread) and Trade Tip 2 nozzle 419

2311661

2311854

TempSpray h 326 (ideal for dispersions/materials with high viscosity)

Basic unit 1/4“ incl. Hose reel, heated hose DN10, 30m, hose 1/4“ DN4, 1m

Spraypack consisting of: Basic unit (2311661), Airless gun AG 14 NPS 1/4“, incl. Trade Tip 2 nozzler holder

(F-thread) and Trade Tip 2 nozzle 421

TempSpray h 126

TempSpray h 226

TempSpray h 326

30

12.6 pump-ruNNer

(order No. 2306987)

Universal accessories for cleaning, clean transportation and preservation of the pump unit.

features:

• Simpler cleaning – the cleaning liquid circulates constantly through the pump making thorough cleaning of the interior

• No cleaning necessary during work stoppage or change of location because the paint in the pump cannot dry out or leak

• Better protection

• Simple assembly

Suitable for the following models:

Diaphragm pumps

SF 21

SF 23

SF 27

SF 31

SF 7000

Finish 270/370

Nespray Deco

Nespray 31

Double-stroke piston pumps

PS 24

PS 26

PS 30

PS 34

PS 3.25

PS 3.29

PS 3.31

PS 3.34

i

Order this at the same time:

EasyClean, cleaning and preservation agent (118ml) Order no. 0508 620.

example of use

31

SpAre pArTS DIAgrAm gB AcceSSorIeS IlluSTrATIoN

3

1

4

2

5

6

PS 3.25

8

7

9

32

PS 3.25

#

1

2

5

6

3

4

7

8

9 pS 3.25

Description

0538 041 Spray gun, Vector Pro 2-finger

0538 040 Spray gun, Vector Pro 4-finger

0538 042 Spray gun, Vector Grip 2-finger

0538 043 Spray gun, Vector Grip 4-finger

0296 441 Pole gun 120 cm, G-thread 7/8”

0296 443 Pole gun 120 cm, F-thread 11/16”

0296 442 Pole gun 200 cm, G-thread 7/8”

0296 444 Pole gun 200 cm, F-thread 11/16”

0345 010 In-line roller IR-100

9984 573 High-pressure hose DN 4 mm, 7.5 m with stainless steel nipple, 1/4”

9984 574 High-pressure hose DN 6 mm, 15 m for dispersion, 1/4”

9984 575 High-pressure hose DN 6 mm, 30 m for dispersion, 1/4”

0034 038 Double socket for coupling high-pressure hoses (1/4” x 1/4”)

0034 950 Metex-Reuse

Reuse for pre-filtering of coating material in vessel. Place suction pipe in the reuse.

0034 952 Sieve package (5 pcs) for paint

0034 951 Sieve package (5 pcs) for dispersion

0034 383 Gun filter, red, 1 piece; 180 mesh extra fine

0097 022 Gun filter, red, 10 pieces; 180 mesh extra fine

0043 235 Gun filter, yellow, 1 piece; 100 mesh fine

0097 023 Gun filter, yellow, 10 pieces; 100 mesh fine

0034 377 Gun filter, white, 1 piece; 50 mesh medium

0097 024 Gun filter, white, 10 pieces; 50 mesh medium

0089 323 Gun filter, green, 1 piece; 30 mesh coarse

0097 025 Gun filter, green, 10 pieces; 30 mesh coarse

0097 108 TipClean Cleaning Set for easy cleaning and conservation of nozzles

0508 619 EasyGlide, special oil (118ml)

0508 620 EasyClean, cleaning and conservation agent (118 ml)

0551 969 Hopper kit

33

SpAre pArTS DIAgrAm gB mAIN ASSemBly

1

5

6

7

8

9

PS 3.25

4

3

2

11

10

12

30

13

14

15

16

17 18 19

22

23

24

21

20

BS4343

25

26

28

51

27

29

0558 466

~110V

6 m

NEMA 5-15P

0290 281 (2.5 m)

0290 284 (4.6 m)

~120V

47

48

49 50

31

36

32

33

34

35

37

38

39

43

44

45

46

40

41

42

34

PS 3.25

#

13

14

15

16

9

10

11

12

7

8

5

6

3

4

1

2

21

22

23

17

18

19

20

24

25

26

27

28 pS 3.25

0508 559

0290 228

0509 218

0558 460

-------

9805 317

0290 212

0290 213

0290 230

9805 403

9810 103

0524 353

0551 757

0290 225

0290 229

9802 266

-------

0522 210

0551 627

0509 218

0290 278

9804 916

0558 307A

0509 218

9805 348

0509 636

0558 298A

0290 205

0290 206

Description

Motor shroud

Set screw

Nut

Nut

Transducer jumper

Electronic cover

Belly pan

Screw (2)

Screw (2)

Door

Screw (2)

Plug*

Strap*

Screw (2)

Handle cover, back

Handle cover, front

Drive assembly

Mounting plate

Fuse, 15A

Screw (4)

Face plate / oiler assembly

Screw

Control panel assembly, complete

(includes items 32-39)

Screw (4)

Screw (4)

Plug (2)

Fluid section assembly

Pusher assembly, stand and low boy cart models (includes item 51)

Pusher assembly, upright cart models

(includes item 51) pS 3.25

0508 553

0508 559

0558 672

0558 565

0507 749

0290 202

0290 218

9850 936

0290 220

0508 579

0522 007

0508 549

0508 550

0508 551

0507 783

0290 224

0508 293

5006 536

0509 218

0522 424

9800 340

0558 452

0558 742

49

50

51

45

46

47

48

41

42

43

44

38

39

40

32

33

34

35

36

37

#

29

30

31

Description

Screw (2)

Screw

Siphon assembly, stand and low boy cart models

Control panel cover with label

Nut with seal

Set screw

Knob

Switch

Digital Electronic Spray Control (DESC) display

Potentiometer

LED assembly

Washer (2)

Screw (2)

Pail hook

Clip

Suction tube

Retun tube

Inlet filter

Screw (4)*

EMI filter, 20A*

Ground screw (2)*

Bracket cover (2)*

Clip

0551 972

0522 054

0522022

Surge protector (not shown, see schematic)

Arrestor (not shown, see schematic)

Display wire assembly (not shown, see schematic)

* UK only

35

SpAre pArTS DIAgrAm

10

16

17

18

19

20

21

11

12

13

14

15

22

8

9

6

7

36 gB fluID SecTIoN

1

2

3

4

5

23

24

PS 3.25

25

26

27

28

29

30

31

32

33

34

#

24

25

26

20

21

22

23

27

28

29

30

16

17

18

19

12

13

14

15

10

11

8

9

6

7

4

5

1

2

3

31

32

33

34

0558 728

0507 254

Description

Retainer

Piston guide

Upper packing

Transducer assembly

Pipe plug

Pump manifold

Fitting

Lower packing

Bushing

Piston rod

Upper cage

Crush washer

Outlet valve ball

Outlet valve seat

Outlet valve retainer

Lower ball guide

Inlet valve ball

Inlet valve seat

O-ring, PTFE

Inlet valve seal

Inlet valve housing

O-ring

Filter

Bearing ring

Filter housing

Conical spring

Bearing spring

O-ring

Gasket

Bypass valve assembly

(includes item 29)

Cam base

Relief valve knob

Groove pin

Return tube fitting

Piston assembly (includes items 10-15)

Repacking kit - 1 (includes items 2-3, 8, 11-13, 17 and

19-20).

Repacking kit - 2 (includes items 2-3 and 8)

Relief valve w/ handle

(includes items 29 – 33) pS 3.25

0509 594

0509 584

-------

0509 581

0290 216

9871 160

0508 748

0508 603

0508 601

0508 602

0508 749

0508 604

0507 745

0558 727

0551 263

50164

0551 620

13481

0509 591

0509 583

0551 534

0509 582

0551 756

0507 517

0290 209

0509 873

-------

0552 489

0290 277

0551 262

0507 931

0508 744

5006 543

9885 612

0509 151

0290 201

PS 3.25

gB DrIve ASSemBly

SpAre pArTS DIAgrAm

1

15

14

13

16

13

#

7

8

5

6

3

4

1

2 pS 3.25

0524 637A

0509 121

0290 282

0508 559

0290 226

0509 218

0558 540

9802 266

Description

Housing assembly

2nd stage gear

Motor assembly

Screw (4)

Baffle assembly

Screw (2)

Electronic control assembly

Screw

17 11

12

#

13

14

15

16

17

9

10

11

12 pS 3.25

0522 023

0551 543

9822 106

0522 040

0551 714

0558 449

0551 980

0509 218

0558 476

* UK only

Description

Capacitor assembly

Tie wrap

Washer

Wire assembly

Cord grip (2)

Bracket*

Lock nut*

Screw (3)*

Power cord jumper*

8

9

10

2

3

4

5

6

7

37

SpAre pArTS DIAgrAm gB STAND

1

2

3

10

4

5 6 7

8

9

PS 3.25

38

#

3

4

1

2

5

6

9

10

7

8 pS 3.25

9805 367

0290 215

0290 211

0294 635

0290 214

0508 660

0294 635

0290 219

0290 214

0290 210

0290 203

0290 204

Description

Screw (3)

Drip cup

Leg, right

Plug

Foot

Screw (2)

Plug

Cord holder

Foot

Leg, left

Left leg assembly (includes items 6-10)

Right leg assembly (includes items 1-5)

PS 3.25

gB SucTIoN SySTem for STAND

1

2

3

#

1

2

3

4

5 pS 3.25

0551 706

9850 638

0558 659A

0279 459

0295 565

Description

Siphon hose

Tie wrap (2)

Return tube

Clip

Inlet screen

0558 672 Siphon tube assembly (includes items

1-5)

4

5

SpAre pArTS DIAgrAm

39

SpAre pArTS DIAgrAm gB uprIghT cArT ASSemBly

1

40

2

3

4

5

#

6

7

4

5

8

9

1

2

3 pS 3.25

0290 207

0290 208

0278 373

0294 534

9890 104

0295 608

0509 386

0294 635

9885 571

Description

Handle assembly (includes items 6-7)

Cart weldment

Wheel (2)

Spacer (4)

Axle cap (2)

Screw (2)

Washer (6)

Plug (2)

Plug (2)

6

7

8

9

PS 3.25

PS 3.25

ImporTANT NoTeS oN proDucT lIABIlITy

As a result of an EC regulation being effective as from January 1, 1990, the manufacturer shall only be liable for his product if all parts come from him or are released by him, and if the devices are properly mounted and operated.

If the user applies outside accessories and spare parts, the manufacturer´s liability can fully or partially be inapplicable; in extreme cases usage of the entire device can be prohibited by the competent authorities (employer´s liability insurance association and factory inspectorate division).

Only the usage of original WAGNER accessories and spare parts guarantees that all safety regulations are observed.

3+2 yeArS guArANTee for profeSSIoNAl fINIShINg

Wagner professional guarantee

(Status 01.02.2009)

1. Scope of guarantee

All Wagner professional colour application devices (hereafter referred to as products) are carefully inspected, tested and are subject to strict checks under

Wagner quality assurance. Wagner exclusively issues extended guarantees to commercial or professional users (hereafter referred to as “customer”) who have purchased the product in an authorised specialist shop, and which relate to the products listed for that customer on the Internet under www.wagnergroup.com/profi-guarantee.

The buyer’s claim for liability for defects from the purchase agreement with the seller as well as statutory rights are not impaired by this guarantee.

We provide a guarantee in that we decide whether to replace or repair the product or individual parts, or take the device back and reimburse the purchase price. The costs for materials and working hours are our responsibility. Replaced products or parts become our property.

2. guarantee period and registration

The guarantee period amounts to 36 months. For industrial use or equal wear, such as shift operations in particular, or in the event of rentals it amounts to

12 months.

Systems driven by petrol or air are also guaranteed for a 12 month period.

The guarantee period begins with the day of delivery by the authorised specialist shop. The date on the original purchase document is authoritative.

For all products bought in authorised specialist shops from 01.02.2009 the guarantee period is extended to 24 months providing the buyer of these devices registers in accordance with the following conditions within 4 weeks of the day of delivery by the authorised specialist shop.

Registration can be completed on the Internet under www.wagner-group.

com/profi-guarantee. The guarantee certificate is valid as confirmation, as is the original purchase document that carries the date of the purchase.

Registration is only possible if the buyer is in agreement with having the data being stored that is entered during registration.

When services are carried out under guarantee the guarantee period for the product is neither extended nor renewed.

Once the guarantee period has expired, claims made against the guarantee or from the guarantee can no longer be enforced.

3. handling

If defects can be seen in the materials, processing or performance of the device during the guarantee period, guarantee claims must be made immediately, or at the latest within a period of 2 weeks.

The authorised specialist shop that delivered the device is entitled to accept guarantee claims. Guarantee claims may also be made to the service centres named in our operating instructions. The product has to be sent without charge or presented together with the original purchase document that includes details of the purchase date and the name of the product. In order to claim for an extension to the guarantee, the guarantee certificate must be included.

The costs as well as the risk of loss or damage to the product in transit or by the centre that accepts the guarantee claims or who delivers the repaired product, are the responsibility of the customer.

4. exclusion of guarantee

Guarantee claims cannot be considered

- for parts that are subject to wear and tear due to use or other natural wear and tear, as well as defects in the product that are a result of natural wear and tear, or wear and tear due to use. This includes in particular cables, valves, packaging, jets, cylinders, pistons, meanscarrying housing components, filters, pipes, seals, rotors, stators, etc.

Damage due to wear and tear that is caused in particular by sanded coating materials, such as dispersions, plaster, putty, adhesives, glazes, quartz foundation.

- in the event of errors in devices that are due to non-compliance with the operating instructions, unsuitable or unprofessional use, incorrect assembly and/or commissioning by the buyer or by a third party, or utilisation other than is intended, abnormal ambient conditions, unsuitable coating materials, unsuitable operating conditions, operation with the incorrect mains voltage supply/frequency, overoperation or defective servicing or care and/or cleaning.

- for errors in the device that have been caused by using accessory parts, additional components or spare parts that are not original Wagner parts.

- for products to which modifications or additions have been carried out.

- for products where the serial number has been removed or is illegible

- for products to which attempts at repairs have been carried out by unauthorised persons.

- for products with slight deviations from the target properties, which are negligible with regard to the value and usability of the device.

- for products that have been partially or fully taken apart.

5. Additional regulations.

The above guarantees apply exclusively to products that have been bought by authorised specialist shops in the EU, CIS, Australia and are used within the reference country.

If the check shows that the case is not a guarantee case, repairs are carried out at the expense of the buyer.

The above regulations manage the legal relationship to us concludingly.

Additional claims, in particular for damages and losses of any type, which occur as a result of the product or its use, are excluded from the product liability act except with regard to the area of application.

Claims for liability for defects to the specialist trader remain unaffected.

German law applies to this guarantee. The contractual language is German. In the event that the meaning of the German and a foreign text of this guarantee deviate from one another, the meaning of the German text has priority. j. Wagner gmbh

Division professional finishing otto lilienthal Strasse 18

88677 markdorf federal republic of germany

- gB -

Note on disposal:

In observance of the European Directive

2002/96/EC on waste electrical and electronic equipment and implementation in accordance with national law, this product is not to be disposed of together with household waste material but must be recycled in an environmentally friendly way!

Wagner or one of our dealers will take back your used Wagner waste electrical or electronic equipment and will dispose of it for you in an environmentally friendly way. Please ask your local Wagner service centre or dealer for details or contact us direct.

41

I gB

D f e eu Declaration of conformity

We declare under sole responsibility that this product conforms to the following relevant stipulations:

2006/42/EC, 2014/30/EU, 2011/65/EU, 2012/19/EU

Applied harmonised norms:

EN ISO 12100, EN 1953, EN 60204-1, EN 61000-3-2, EN

61000-3-3, EN 61000-6-1, EN 61000-6-3,

The EU declaration of conformity is enclosed with the product.

If required, it can be re-ordered using order number

2385803.

eu konformitätserklärung

Wir erklären in alleiniger Verantwortung, dass dieses Produkt den folgenden einschlägigen Bestimmungen entspricht:

2006/42/EG, 2014/30/EU, 2011/65/EU, 2012/19/EU

Angewandte harmonisierte Normen:

EN ISO 12100, EN 1953, EN 60204-1, EN 61000-3-2, EN

61000-3-3, EN 61000-6-1, EN 61000-6-3

Die EU Konformitätserklärung liegt dem Produkt bei.

Sie kann bei Bedarf mit der Bestellnummer 2385803 nachbestellt werden.

Déclaration de conformité ue

Nous déclarons sous notre responsabilité que ce produit est en conformité avec les réglementations suivantes:

2006/42/CE, 2014/30/UE, 2011/65/UE, 2012/19/UE

Conforme aux normes et documents normalisés:

EN ISO 12100, EN 1953, EN 60204-1, EN 61000-3-2, EN

61000-3-3, EN 61000-6-1, EN 61000-6-3

La déclaration de conformité UE est jointe à ce produit.

Elle peut être commandée au besoin sous le numéro de commande 2385803.

Dichiarazione di conformità ue

Dichiariamo sotto la nostra esclusiva responsabilità, che il presente prodotto corrisponde alle relative disposizioni seguenti:

2006/42/CE, 2014/30/UE, 2011/65/UE, 2012/19/UE

Norme armonizzate:

EN ISO 12100, EN 1953, EN 60204-1, EN 61000-3-2, EN

61000-3-3, EN 61000-6-1, EN 61000-6-3

La dichiarazione di conformità UE è allegata al prodotto.

Se necessario, può esserne richiesta una copia con il numero d’ordine 2385803.

Declaración ue de conformidad

Mediante la presente garantizamos, bajo nuestra exclusiva responsabilidad, que este producto cumple con las correspondientes disposiciones:

2006/42/CE, 2014/30/UE, 2011/65/UE, 2012/19/UE

Normas armonizadas aplicadas:

EN ISO 12100, EN 1953, EN 60204-1, EN 61000-3-2, EN

61000-3-3, EN 61000-6-1, EN 61000-6-3

El producto viene acompañado de la declaración UE de conformidad. Si lo necesita, puede pedirla adicionalmente por el número de pedido 2385803.

Nl

Dk

S p eu-conformiteitsverklaring

Wij verklaren dat dit product voldoet aan de volgende normen:

2006/42/EG, 2014/30/EU, 2011/65/EU, 2012/19/EU

En normatieve dokumenten:

EN ISO 12100, EN 1953, EN 60204-1, EN 61000-3-2, EN

61000-3-3, EN 61000-6-1, EN 61000-6-3

De EU-conformiteitsverklaring wordt met het product meegeleverd.

Indien nodig kan de verklaring met bestelnummer

2385803 worden nabesteld.

eu overensstemmelseserklæring

Vi erklærer under almindeligt ansvar, at dette produkt er i overensstemmelse med følgende bestemmelser:

2006/42/EF, 2014/30/EU, 2011/65/EU, 2012/19/EU

Anvendte harmoniserede normer:

EN ISO 12100, EN 1953, EN 60204-1, EN 61000-3-2, EN

61000-3-3, EN 61000-6-1, EN 61000-6-3

EU Overensstemmelseserklæringen er vedlagt produktet.

Om nødvendigt kan den efterbestilles med bestillingsnummer 2385803.

eu konformitetsförklaring

Vi intygar och ansvarer för, att denna produkt

överensstämmer med följande norm och dokument:

2006/42/EG, 2014/30/EU, 2011/65/EU, 2012/19/EU

Använta harmoniserade normer:

EN ISO 12100, EN 1953, EN 60204-1, EN 61000-3-2, EN

61000-3-3, EN 61000-6-1, EN 61000-6-3

EU-konformitetsförklaringen medföljer produkten. Den kan vid behov beställas genom ordernummer 2385803.

Declaração de conformidade ue

Pela presente garantimos, soba nossa exclusiva responsabilidade, que este produto cumpre com as correspondentes disposições:

2006/42/CE, 2014/30/UE, 2011/65/UE, 2012/19/UE

Normas harmonizadas aplicadas:

EN ISO 12100, EN 1953, EN 60204-1, EN 61000-3-2, EN

61000-3-3, EN 61000-6-1, EN 61000-6-3

A Declaração de Conformidade EU é fornecida juntamente com o produto.

Se necessário, pode ser pedido novo exemplar desta declaração com o número de encomenda 2385803.

42

PS 3.25

Berlin

J. Wagner GmbH

Service-Stützpunkt

Flottenstraße 28–42

13407 Berlin

Tel. 0 30/ 41 10 93 86

Telefax 0 30 / 41 10 93 87 grünstadt

J. Wagner GmbH

Service-Stützpunkt

Dieselstraße 1

67269 Grünstadt

Tel. 0 63 59/ 87 27 55 0

Telefax 0 63 59/ 80 74 80 ratingen

J. Wagner GmbH

Service-Stützpunkt

Siemensstraße 6-10

40885 Ratingen

Tel. 0 21 02 / 3 10 37

Telefax 0 21 02 / 3 43 95 heidersdorf in Sachsen

J. Wagner GmbH

Service-Stützpunkt

Olbernhauer Straße 11

09526 Heidersdorf

Tel. 03 73 61 / 1 57 07

Telefax 03 73 61 / 1 57 08 hannover

J. Wagner GmbH

Servicestützpunkt

Kornstraße 20

31535 Neustadt

T el. 0 50 32-8 00 06 23

Telefax 0 50 32-8 00 06 24 münchen

Jahnke GmbH

Hochstraße 7

82024 Taufkirchen

Tel. 0 89 /6 14 00 22

Telefax 0 89 / 6 14 04 33 email: [email protected]

www.airless.de

Nürnberg

Grimmer GmbH

Starenweg 28

91126 Schwabach

Tel. 0 91 22 / 7 94 73

Telefax 0 91 22 / 7 94 75 0 email: [email protected]

www.grimmer-sc.de

markdorf – Zentrale

J. WAGNER GmbH

Otto-Lilienthal-Straße 18

88677 Markdorf

Postfach 11 20

88669 Markdorf

Tel. 0 75 44 / 505-0

Telefax 0 75 44 / 505-1200 www.wagner-group.com

kundenzentrum

Tel. 0 75 44 / 505-1666

Telefax 0 75 44 / 505-1155 email: [email protected]

Technischer Service

Tel. 0180 5 59 24 637

(14 Cent/Minute aus dem deutschen

Festnetz, Mobilfunk max. 42 Cent/Min)

WAgNer koNTAkTNeTZ DeuTSchlAND, Im INTerNeT Zu fINDeN uNTer: WWW.WAgNer-group.com/profI

43

A

B

J. Wagner Ges.m.b.H.

Ottogasse 2/20

2333 Leopoldsdorf

Österreich

Tel. +43/ 2235 / 44 158

Telefax +43/ 2235 / 44 163 [email protected]

WSB Finishing Equipment

Veilinglaan 56-58

1861 Meise-Wolvertem

Belgium

Tel. +32/2/269 46 75

Telefax +32/2/269 78 45 [email protected]

ch Wagner International AG

Industriestrasse 22

9450 Altstätten

Schweiz

Tel. +41/71 / 7 57 22 11

Telefax +41/71 / 7 57 22 22 [email protected]

D

J. Wagner GmbH

Otto-Lilienthal-Straße 18

D-88677 Markdorf

Postfach 11 20

D-88669 Markdorf

Deutschland

Tel.: +49 / 75 44 / 505 -1664

Fax: +49 / 75 44 / 505 -1155 [email protected]

www.wagner-group.com

cZ E-Coreco s.r.o.

Na Roudné 102

301 00 Plzeň

Czechia

Tel. +420 734 792 823

Telefax 420 227 077 364 [email protected]

Dk Wagner Spraytech

Scandinavia A/S

Helgeshøj Allé 28

2630 Taastrup

Denmark

Tel. +45/43/ 27 18 18

Telefax +45/43/ 43 05 28 [email protected]

e Makimport Herramientas, S.L.

C/ Méjico nº 6

Pol. El Descubrimiento

28806 Alcalá de Henares (Madrid)

Tel. 902 199 021/ 91 879 72 00

Telefax 91 883 19 59 [email protected]

[email protected]

f Euromair Antony f

S.A.V. Ile-de-France

12-14, av. F. Sommer

92160 Antony

Tel. 01.55.59.92.42

Telefax +33 (0) 1 69 81 72 57 [email protected]

Euromair Distribution

Siège Social / S.A.V. Sud

343, bd. F. Perrin

13106 Rousset Cedex

Tel. 04.42.29.08.96

Telefax 04.42.53.44.36

[email protected]

ru OOO Мефферт Полилюкс

142407 Россия, Московская обл,

Ногинский р-н, территория

«Ногинск-Технопарк» д.14

Tel. +7 495 221 6666

Telefax +7 495 99 55 88 2

[email protected] [email protected]

I

gB Wagner Spraytech (UK) Limited

The Coach House

2 Main Road

Middleton Cheney OX17 2ND

Great Britain

UK-Helpline 01295 714200

Fax 01295 710100 [email protected]

Wagner S.p.A.

23868 Valmadrera (Lc)

Via Santa Vecchia, 109

Italia

Tel./Fax 0341 210100 (centralino) [email protected]

Nl WSB Finishing Equipment BV

De Heldinnenlaan 200,

3543 MB Utrecht

Netherlands

Tel. +31/ 30/241 41 55

Telefax +31/ 30/241 17 87 [email protected]

S Wagner Spraytech

Scandinavia A/S

Helgeshøj Allé 28

2630 Taastrup

Denmark

Tel. +45/43/ 21 18 18

Telefax +45/43/ 43 05 28 [email protected]

wagner-group.com

44