Powr-Flite PF50, PF70, PF70DC, PF757 Owner's Manual

 COMMERCIAL
VACUUM CLEANER
Model PF50, PF70
Model PF70DC, PF757
Owner’s Guide
—
EVERYTHING WHOLESALE
Where Unsung Heroes Make It Happen”™
800.647.2737 NationalEW.com
Wholesale Parts Pricing
IMPORTANT SAFEGUARDS
When using an electrical appliance, basic precautions should always be followed,
including the following:
READ ALL INSTRUCTIONS BEFORE USING THIS VACUUM CLEANER.
WARNING
To reduce the risk of fire, electric shock, or injury:
Do not use outdoors or on wet surfaces.
Do not leave vacuum cleaner when plugged in. Turn off the switch and unplug the
electrical cord when not in use and before servicing.
Do not allow to be used as a toy. Close attention is necessary when used by or near
children.
Use only as described in this manual. Use only manufacturer's recommended
attachments.
Do not use with damaged cord or plug. If vacuum cleaneris not working as it should,
has been dropped, damaged, left outdoors, or dropped into water, return it to a
service center before using.
Do not pull or carry by cord, use cord as a handle, close door on cord, or pull cord
around sharp edges or corners. Do not run vacuum cleaner over cord. Keep cord
away from heated surfaces.
Connect to a properly grounded outlet only (refer to Grounding Instructions).
Do not use extension cords or outlets with inadequate current carrying capacity.
Turn off all controls before unplugging.
Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord,
Do not handle plug or vacuum cleaner with wet hands.
Do not put any object into openings. Do not use with any opening blocked; keep
free of dust, lint, hair, and anything that may reduce airflow.
This vacuum cleaner creates suction and contains a revolving brush roll. Keep hair,
loose clothing, fingers, and ali parts of body away from openings and moving parts.
Do not pick up anything that is burning or smoking, such as cigarettes, matches, or
hot ashes.
Do not use without dust bag in place.
Beit pulleys can become hot during normal use. To prevent burns, avoid touching
the belt pulley wnen servicing the drive belt.
Use extra care when cleaning on stairs.
Do nat use to pick up flammable or combustible liquids such as gasoline, or use in
areas where they may be present.
Store your cleaner indoors in a cool, dry area.
Keep your work area weil lighted.
Unplug electrical appliances before vacuuming them.
SAVE THESE INSTRUCTIONS
CONSEILS DE SECURITE
Lors de l'utilisation d'un appareil électrig ue, quelques précautions élémentaires doivent
étre observées, incluant les suivantes:
LISEZ TOUTES LES INSTRUCTIONS AVANT D'UTILISER VOTRE ASPIRATEUR.
AVERTISSEMENT
Pour réduire le risque de feu, de choc électrique, ou de blessure:
Ne pas utiliser à l'extérieur où sur des surfaces mouillées.
Fermez le commutateur et débranchez l'appareil lorsque vous ne l'utilisez pas ou
avant le nettoyage ou l'entretien.
Ne permettez pas qu'il soit utilisé comme jouet. Une attention particulière est.
nécessaire lorsque utilisé par ou prés d'un enfant.
Suivez les recommandations d'utilisation de ce manuel, Utilisez uniquement les
accessoires recommandés par le fabriquant.
Ne pas utiliser si le cordon ou la fiche sont endommagés. Si l'aspirateur ne fonctionne
pas comme il le devrait, s’il a été échappe, s'il est endommagé, s'il a été laissé à
l'extérieur ou échappe dans l'eau, retournez-le à un centre de service avant d'utiliser.
Ne pas le tirer ou le transporter par le cordon, ne pas utiliser le cordon un guise de
poignée. Ne pas fermer une porte sur le cordon ou tirer le cordon sur des coins ou
bordures pointus. Ne pas circuler sur le cordon avec l'aspirateur. Tenir le cordon a
distance des surfaces chauffantes.
Branchez toujours l'aspirateur dans une prise à trois (mise à la terre).
Ne pas utiliser des rallonges ou des prises qui n'ont pas de capacité suffisante pour
transporte le courant.
Fermer tous les contrôles avant de débrancher.
Ne pas débrancher en tirant sur le cordon. Pour débrancher, tenez la fiche et non le
cordon.
Ne pas manipuler la fiche ou l'aspirateur avec les mains mouillées.
Ne pas rien insérer dans les ouvertures. Ne pas utiliser si des ouvertures sont
bloquées; assurez-vous qu'elles soient dégagées de poussière, mousse. cheveux
où toute autre chose qui pourrait réduire le passage de l'air.
Get aspirateur crée de la succion et contient un rouleau-brosse tournant. Tenir les
parties mobiles et les ouvertures loin des cheveux, du linge, des doigts et de toute
partie du corps.
Ne pas ramasser des objets qui brülent où fument Comme les cigarettes, allumettes
ou cendres chaudes.
N'utilisez pas sans le sac de poussière en place.
Les poulies du courroie peuvent devenir chaudes pendant l'utilisation normale. Pour
prévenir des brûlures, évitez de touché la poulie du courroie lorsque vous réparez la
courroie.
Portez une attention particulière lorsque vous nettoyez les escaliers.
Ne pas utiliser pour ramasser des liquides inflammables où com bustibles comme de
l'essence. Ne pas utiliser dans les endroits où ces liquides pourraient être présents.
Entreposez votre aspirateur à l'intérieur dans un endroit propre et sec.
Maintenez un bon éclairage à l'endroit où vous travaillez.
Débrancher les appareils électrique avant de les balayer.
CONSERVEZ CES INSTRUCTIONS
Grounding Instructions
This appliance must be grounded. If it should malfunction or breakdown, grounding
provides a path of ieast resistance for electric current to reduce the risk of electric shock.
This appliance is equipped with a cord having an equipment-grounding conductor and
grounding plug. The plug must be plugged into an appropriate outlet that is properly
installed and grounded in accordance with all local codes and ordinances.
DANGER
Improper connection of an equipment-grounding conductor can result in risk of electric
shock. Check with a qualified electrician or service person if you are in doubt as to
whether the outlet is properly grounded. Do not modify the plug provided with the
appliance. If it will not fit the outlet, have proper outlet installed by a qualified electrician,
This appliance is for use on a nominal 120 volt circuit and has a grounding plug that
looks like the plug illustrated in Figure A. Atemporary adapter which looks like the adapter
illustrated in Figure B may be used to connect this plug to a two-pole receptacle, as
shown, if a properly grounded outlet is not available. The temporary adapter should be
used only until a properly grounded outlet, Figure A, can be installed by a qualified
électrician. The green colored rigid ear, lug, or the like extending from the adapter must
be connected to a permanent ground such as a properly grounded outlet box cover.
Whenever the adapter is used, it must be held in place by a metal screw.
NOTE: In Canada, the use ofatem porary adapter is not permitted by the Canadian
Electrical Code.
GROUNDED GROUNDED
OUTLET BOX OUTLET BOX
ADAPTER
F 4
GROUNDING BLADE FIGURE A
IS LONGEST OF THE METAL FIGURE B
THREE BLADES
SCREW GROUNDING
TAB
4
INSTRUCTIONS VISANT LA MISE A LA TERRE
Cet appareil doit étre mis á la terre. En cas défaillance ou de panne éventuelles, la
mise à la terre fournit au courant un chemin de moindre résistance qui réduit le risque
de choc électrique. Cet appareil est pourvu d'un cordon muni d'un conducteur de terre
et d'une fiche avec brache de terre. La fiche doit être branchée dans une prise
apprapriée correctement installée et mise à la terre conformément aux règlements et
ordonnances municipaux.
AVERTISSEMENT
Un conducteur de terre mal raccordé peut entraîner un risque de choc électrique.
Consulter un électricien ou un technicien d'entretien qualifié si vous n'êtes pas certain
que la prise est correctement mise à la terre. Ne pas modifier la fiche fournie avec
l'appareil-si elle ne peut être insérée dans la prise, faire installer une prise adéquate
par un électricien qualifié,
Note. Au Canada, l'utilisation d'un adaptateur temporaire n'est pas autorisée par le
Code canadien de l'électricité.
Cet appareil est destiné à un circuit de 120 V et est muni d'une fiche de mise à la terre
semblable à celle illustrée par le Figure A. S'assurer que l'appareil est branché à une
prise de courant ayant la même configuration que la fiche. Aucun adaptateur ne devrait
être utilisé avec cet appareil.
Boite de Prise de Terre
=
/ FIGURE A
LA LAME DE TERRE
EST LA PLUS LOUNGE
DES TROIS LAMES
GENERAL INFORMATION
The cleaner is designed to pick up dirt and dust Particles. Avaid picking up hard or
sharp objects with the cleaner to prevent bag tears, hose clogs, and fan blade breakage
with subsequent motor damage.
Service Information
To obtain the most satisfying years of service read through these instructions and
keep them handy for future reference. If you require service, contact the dealer from
whom the cleaner was purchased. NOTE: Turn off the switch and unplug the
electrical cord before servicing the unit.
DO NOT OIL the motor to the brush roll at any time. The bearings are
permanently lubricated and sealed.
Rating Plate
The model, type and serial numbers are
indicated on the rating plate located on
the bottom ofthe cleaner. For prompt and
complete service information, always refer (Up)
MODEL TYPE SERIAL NO,
VOLTS AMPS. HERTZ
to these numbers when inquiring about | aso
service.
Model & Type
Serial No.
HOW TO ASSEMBLE
Assembly Packet
The assembly packet is with the a
owner's guide. The packet contains two La:
2-part bolts and two cord hooks. An if
extra drive belt is also included with
some models.
Step 1
Assemble the Handle
Slip the upper handle and the lower
handle together so the handle bolt
holes align and the slots in the handle
are positioned as shown in Detail A.
Insert a 2-part bolt (A) in the center of
the handle and tighten.
Hold the assembled handle so it curves
away from the cleaner. Then push the
handle into the handle socket (D) at the
rear of the cleaner. Align the holes,
insert the other 2-part bolt (A), and
tighten.
6
Step 2
Attach The Cord Hooks
Upper Cord Hook
Pull the spring on the electrical cord
upward toward the top of the handle.
Make sure slots in handle are
positioned properly, see Detail A.
Insert the lower half of the spring into
the upper cord hook (B), as shown.
Snap the hook into the upper handle,
directions below.
1. Place inner tab 2. Press hook 3. SNAP opposite inner
into slot around handle tab into place
Step 3
Lower Cord Hook
Insert the power cord into ihe lower
cord hook (C), as shown. Snap the
hook into the lower handle. Pull up on
the cord to tighten but leave enough
slack near the base so the cord is not
strained when the handle is lowered.
Wrap the cord around the two cord
hooks. Fasten the plug to the cord to
prevent unwinding.
Step 4
Install The Bag
Insert the bag adapter clip (E) on the
bottom of the bag collar into the bag
adapter retainer (F).
Push the bag collar up and forward so
the locator lug slides into the slot
indicated by the arrow. Then turn the
cam latch (G) to lock the bag onto the
rivet (H).
Loop the spring from the top of the bag
onto the bag support located to the back
of the upper cord hook (В).
BAG
SUPPORT
HOOK
HOW TO ASSEMBLE (PF70DC)
CAUTION: Fully assemble the cleaner 9 9
before using. 8 8 q >
A B С D
Assembly Packet 2-Part Cord Bellows Cord
The assembly packet contains two e-part Handle Hook Screws Clamp
handle bolts, 1 cord hook, 2 bellows screws Bolts and
and 1 cord clamp with a screw. An extra Screw
belt is included with some models.
Secure Bellows
Check to be sure the end of the bellows is
secure in the chrome bellows adapter. Align
the screw holes in the bellows adapter with
the back of the base, start the screws (C)
by hand, and tighten.
Attach Lower Handle
Raise the dust cup support. Push the lower
handle (largest end down) through the tube
of the dust cup support and into the handle
socket at the back of the cleaner, Align the
holes, insert a 2-part bolt (A), and tighten.
Dust Cup
Lower Support
Handle
Assemble Upper Handle
Hold the upper handle so it curves
away from the cleaner. Then push it
down over the lower handle. Secure
with the other 2-part handie bolt (A).
Upper
Handle
Lower
Handle
Handle
Socket
Open Dust Cup Lid
Release each latch on the dust.cup
support (push down on the lock, lift up
on the bottom of the latch and pull the
top forward). Swivel the lid up and
outward.
Attach Cloth Bag
Hold the cloth bag by the lower rim so
the front faces away from the cleaner.
Drop the bag through the open lid.
Push each tab on the lower bag rim into
the notches on the dust cup lid. Swivel
the lid over the dust cup support and
secure each latch.
Secure Cord Clamp
Secure the electrical cord to the dust
cup support with the cord clamp and
screw (D). Place the cord clamp over
the electrical cord. Screw the clamp to
the tab below the left latch; start the
screw by hand, then tighten.
Attach The Cord Hook
Pull the spring on the electrical cord
Upward toward the top of the handle.
Insert the lower half of the spring into
the cord hook (B). Snap the hook into
the upper handle, directions below.
a | F
AE Ana | |
I Y <<
1. Place 2. Presshook 3. SNAP opposite
inner tab around Inner tab into
into slot handle place
Pull up on the cord to tighten butleave
enough slack near the base so the cord
is not strained when the handle is
lowered,
store Electrical Cord
Loop the cord around the cord hook and
secure the plug to prevent unwinding.
Hook Bag Top
Slip the ring at the top of the cloth bag over
the bag support hook on the back of the
cord hook.
HOW TO USE
The upright vacuum cleaner is designed to be used on multiple types of carpeting. Do
not attempt to use the upright vacuum cleaner on bare floors, as damage to the
floor covering may result,
Handle Adjustment
With the tip of the foot, press down to release
the handle lock located at the left rear side
of the cleaner. Move the handle and adjust it
to the desired position for (1) storing upright,
(2) operating the cleaner at a comfortable
height for the user, and (3) cleaning
underneath low furniture.
Power Switch
The power switch is mounted on the motor
hodd. A push with the foot turns the motor
ON; push again to turn the motor OFF.
Cord Storage
The cleaner has two convenient cord storage
hooks attached to the handle. Wind the cord
around the hooks and fasten the plug to the
cord to prevent unwinding.
10
¿7 1. Store
7 ss 2. Use
E e
y A
| À И À
MA И A
| | 4]
| И |
и Z 3. Clean
| + £ Underneath
un
: Bt Im
Handle Lock
ON/OFF
Cleaner Height Setting
WARNING: Avoid injury. Keep.loose clothing, hair, fingers, and all other parts
of body away from any moving part (such as the revolving brush),
Turn off the switch and unplug the cleaner before changing the
cleaner height setting.
Adjust the vacuum cleaner height setting to match the carpet pile height. Refer to the
following chart of recommended settings for Carpet types.
The front of the cleaner has either a knob Recommended
or slide adjustment which raises orlowers Setting Example of Carpet
the cleaner base to match the type of | Position 1 —foromonm Low pile as kitchen, indoor.
carpet. With the cleaner cord unplugged, outdoor
set the adjustment according to the table | Position 2 eds Scuiptured
as a Starting point. While the cleaner is ic di | |
off and disvantectod from the outlet, | "on = Se OP ARCHE BETTER
place the handle in the operating position, | Pesition + Thick plush
tilt the cleaner back to remove the weight | tthe cleaner has additional height settings, they are lor thicker
from the wheels, and adjust the setting, 1 FE!s a7 where easier pushing is desired
Then plug the cleaner into the electrical outlet, turn on the switch, lower the handle, and
pass the cleaner over the carpet. If the cleaneris still difficult to push, follow the procedure
and test the cleaner at the next higher setting. Continue testing the setting until the
cleaner is comiortable to move. Moving the knob or slide to the next higher setting raises
the brush roll slightly, making the cleaner easier to push. However, the brush rall must
make contact with the carpet for effective cleaning,
HOW TO MAINTAIN
The instructions given in this booklet serve as a guide to routine maintenance. To
avoid unnecessary service calls, check the bag, belt and brush roll often.
Fan Chamber Cover (PF757)
NOTE: Turn off the switch and unplug the electrical cord before cleaning.
The clear, removable fan chamber cover provides easy Mm
inspection, cleaning, and maintenance of the fan chamber
Removing the cover provides easy access to the motor tan.
Grease buildup, dirt, or other obstructions, visible through
the fan cover, should be removed. To clean the fan area,
take off the chrome bottom plate by releasing the two cam
locks (see Brush Roll Belt, Figure 1 and 2). Remove the belt
from the motor pulley, then loosen and remove the screws
on either side of the fan cover, as indicated by the arrows.
Push the cam locks outward against the wheels to lift the
cover from the cleaner base. Dirt and obstructions can easily
be cleared; however, caked grease may need to be scraped from the cover and the
cleaner. If the fan does not turn freely, it also should be removed for cleaning. To
remove the fan, place a wrench over the motor pulley. Hold the fan blades with one
hand and turn the wrench counterclockwise. Remove ihe motor pulley and lift the fan
off the motor shaft. Clean the area and replace the fan over the motor shaft, Tighten
the motor pulley snugly clockwise with the wrench. If necessary, replace the fan cover
or the gasket with replacement parts.
Be sure the gasket is in place. Reposition the fan cover by first placing the exhaust
end into place between the large rear wheels. Seat the fan cover firmly. Next replace
the belt and bottom plate as the pressure from the bottom plate helps seal the fan
cover, Start the two screws by hand to be sure they are straight, then tighten.
Order fan chamber cover replacement kit (fan cover, gasket, two screws).
Aus
11
Cleaner Care
NOTE: Turn off the switch and unplug the electrical cord before cleaning unit,
To keep the vacuum cleaner looking new, it can be wiped with a damp cloth and a mild
soap solution, then thoroughly dried. Never use any type of chemical, as chemicals can
damage the cleaner. When notin use, the cleaner should be stored in a clean, dry place.
Dust Cup and Bag (PF70DC)
The cloth bag and the dust cup play a very important role in the efficiency of the
vacuum cleaner. The cloth bag allows air to move through the cleaner while it traps
dirt inside the cloth bag and the dust cup. When dirt particles cling to the cloth bag,
they can restrict airflow. If air cannot pass through the cloth bag, no cleaning can take
place regardless of how powerful the unit, Some fine particles can restrict airflow very
quickly and will decrease performance even before the dust cup appears to be full.
For that reason, when vacuuming powder, flour dust, or similar fine substances, it may
be necessary to turn off the cleaner and empty the dust cup more often.
NOTE: Turn off the switch and unplug the electrical cord before emptying the
dustcup. Never operate the vacuum cleaner without the dust cup latched
in place. 1. Unhook
1. Unhook the clip from the top of the
cloth bag.
2. Shake the cioth bag to release dust
clinging inside.
3. Release each latch, one on either
side of the handle (push down on
the lock, lift up on the bottom and
pull the top forward.)
NOTE: Keep the latch free of dust
or obstructions that would
prevent it from locking securely.
3. Release
4. Lift the lid; swing it up and outward.
on
. Reach in, grasp the dust cup and
pull it out of the support.
6. Empty contents in a suitable
container. (/f desired, the cup can
be washed in warm waiter using a
mild soap solution. Be sure the cup
is completely dry before repla cing.)
7.~Place the cup into the support,
Swing the lid shut, and fasten each
latch.
8. Hook clip to top of bag (refer to item
1).
12
Dust Bag
The dust bag plays a very important role in the efficiency of the vacuum cleaner. The bag
traps the dirt and allows the air to pass th rough. If the bag (either cloth or paper} becomes
clogged, no air can pass through the cleaner and no cleaning can take place, regardless
of how powerful the unit is. To keep the cleaner operating at maximum efficiency, empty
or change the dust bag frequently. Some fine particles can restrict air flow very quickly
and will decrease performance even before the bag appears to be full. For that reason,
when vacuuming carpet fresheners or cleaners, powder, plaster dust, or similar fine
substances, the bag may need to be cleaned or changed more often.
NOTE: Turn off the switch and unplug the electrical cord before emptying the
bag. Never operate the vacuum cleaner without the dust bag.
How To Empty Reusable Dust Bag
=
A m Ha Bern
1. Pull bag out open end of clamp,
ww
4. Insert bag adapter clip (B) into bag
E adapter retainer (C).
5. Push bag collar up and forward so
A locator lug (D) slides into slot (E),
6. Turn cam latch to lock bag collar
onto shoulder rivet.
2. Turn cam latch (A) on bag collar to 7, Fold top of bag and slide back into
release. clamp.
3. Place top of bag into appropriate
container. Hold bag collar and NOTE: Never wash or dry-clean
shake vigorously several times. cloth bag.
(Bag can be tumed wrong side out
and brushed with a whisk broom.)
How To Change Disposable Dust Bag-Style F & С
1. Pull 2. Roll E 4 |
zipper down AS fi
и | DZ
down coil
- fe 5. Place bag
~ throat on
sleeve
=
>
4. Unfold 6. Roll up coil spring
hos 7. Place paper bag into outer bag
‘I NOTE: Be certain there are no
folds at the top or bottom of
3. Pull bag the paper bag.
throat off 8. Lift zipper
sleeve 13
Brush Roll
As the brush roll rotates, it sweeps and combs the Carpet nap. Remove hair and threads
from the brush roll so it continues brushing the carpet nap, When the bristles of the
brush roll no longer touch a straight edge held across the bottom plate, the brush roll
is Ineffective because the bristles no jon ger touch the carpet nap. To maintain the most
effective cleaning, use a new wood brush roll. Replace the brush strips on the chromed
steel brush roll.
How To Replace Worn Brush Strips
NOTE: Turn off the switch and unplug the electrical cord before replacing brush
Strips.
New brush strips are supplied in sets of two, one long and one short. To replace,
remove bottom plate and belt (see How To Change Belt). Then, grasp center of brush
roll and lift to remove,
A. Remove rubber end cap cover from F. Slide in new brush strip of same
one end. length {rounded end first). Fit track
В. Unscrew locknut. on either side into brush roll slot.
C. Remove end cap. Replace second brush strip from
: opposite end of brush roll.
D. Remove bearing retainer. E. Ben! hafı
E. Push shaft through opposite end. D au q 4 8 E а a
Е. Pull out worn brush strip with pliers. en ee on ety Asa
retainer with brush strip on both
ends of brush roll.
C. Position end cap with flat sides of
center hole over flat sides of
threaded shaft.
B. Tighten locknut.
A. Align holes and secure rubber end
cap cover flat side against end
cap.
When properly assembled, the brush roll should rotate freely between the two end
caps. Check the condition of the belt: change if necessary. Replace the brush roll. belt,
and bottom plate (see How To Replace A Worn Belt).
14
Brush Roll Belt
The brush roll beit on the upright vacuum cleaner drives tne brush to agitate, sweep,
and comb the carpet nap. The belt should be checked regularly to be sure itis in good
condition. Replace the belt if it is stretching, cracking, or slipping. Cut away any hair or
thread wound around the brush roll or the belt pulley because the buildup could cause
the belt to rotate unevenly,
How To Replace A Worn Belt
NOTE: Turn off the switch and unplug the electrical cord before replacing belt.
Belt pulleys can become hot during normal use. To prevent burns, avoid
touching the belt pulley when servicing the drive belt.
IMPORTANT: Improper installation of the brush roll or brush roll belt could cause
carpet or cleaner damage.
9 Motor
2. Pull up on belt to rotate it off the
motor pulley. Lift up on brush roll
and remove worn belt.
‘OF
Г
17 ]
Check for brush wear (see Brush Roll — r 2
instructions). >. Place rubber end cap covers over
3. Place new belt around brush roll. both end caps (flat side against end
4. Align brush roll pulley with belt cap). Align the holes and secure.
guide, Then, slant brush roll forward so
end caps are in line with slots in
cleaner base.
6. Push brush roll into place.
7. Place lower side of belt into belt
guide and pull to stretch the belt
around the left side of motor pulley.
Rotate pulley to secure belt into
groove. 8. Place slots of bottom plate over
tabs of cleaner base.
9. Seat and secure cam locks.
Headlight Bulb (standard on some models)
NOTE: Turn off the switch and unplug the electrical cord before replacing
headlight bulb. '
Headlight style varies by model. Locate the notches that release the tabs at either (1)
top, (2) side, or (3) bottom of the lens, as illustrated. Place a screwdriver into one
notch; twist or pry the screwdriver to release the lens. Repeat for the second notch on
the opposite side.
Rotate the bulb socket forward. Push bulb in and turn to remove. Secure new bulb into
socket and rotate bulb socket backward.
Replace the lens tabs into the top of the bottom of the hood opening. Rotate lens to
position and press down at each notch until the lens locks into position.
NOTE: Use 25 watt replacement bulb, only.
or,
(1
IIA DD dl
me Powr-Flite? имтес МАВВАМТУ =
Your Powr-Flite Cleaner has been thoroughly tested, inspected
and is guaranteed to be free from defects in workmanship and materials
for a period of one year from date of purchase. The cleaner must be
used on the electric current stated on the motor rating plate.
ODO
=. The Company will supply new parts for defective parts atno charge. E
=33 Cleaners returned for guarantee service must be shipped мин
= transportation Charges prepaid. Before returning for guarantee service, =
= write for shipping instructions and authorization. =
=S This guarantee does not cover parts requiring replacement due to a
== normal wear orto abuse or negligence of the user. Belts, agitation brushes >
—=4 and bags are excluded from this guarantee. ES
=; A TACONY COMPANY =
AR RE RE ER ER ER TENTE ET TT TS PET re
А
=
ss
=
ae
Reel
el
2a
=
L 21
RE
nr
=
=
Le:
A
—
"Ebo
=.
LL
A
к
Е =
—=
Er
==
a
=
aa
ie
=
A
L 3
a
Part No, 582404 (10/98) Printed in U.S.A.