advertisement
▼
Scroll to page 2
of
72
AV SURROUND RECEIVER AVR-1709 Owner’s Manual Manuel de l’Utilisateur ENGLISH FRANCAIS SAFETY INSTRUCTIONS n SAFETY PRECAUTIONS 1. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. Read Instructions – All the safety and operating instructions should be read before the product is operated. 2. Retain Instructions – The safety and operating instructions should be retained for future reference. 3. Heed Warnings – All warnings on the product and in the operating instructions should be adhered to. 4. Follow Instructions – All operating and use instructions should be followed. 5. Cleaning – Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. 6. Attachments – Do not use attachments not recommended by the product manufacturer as they may cause hazards. 7. Water and Moisture – Do not use this product near water – for example, near a bath tub, wash bowl, kitchen sink, or laundry tub; in a wet basement; or near a swimming pool; and the like. 8. Accessories – Do not place this product on an unstable cart, stand, tripod, bracket, or table. The product may fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufacturer’s instructions, and should use a mounting accessory recommended by the manufacturer. 9. A product and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn. 10. Ventilation – Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to. 11. Power Sources – This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. For products intended to operate from battery power, or other sources, refer to the operating instructions. 12. Grounding or Polarization – This product may be equipped with a polarized alternating-current line plug (a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug. FIGURE A EXAMPLE OF ANTENNA GROUNDING AS PER NATIONAL ELECTRICAL CODE "/5&//" -&"%*/ 8*3& (306/% $-".1 "/5&//" %*4$)"3(&6/*5 /&$4&$5*0/ &-&$53*$ 4&37*$& &26*1.&/5 (306/%*/($0/%6$5034 /&$4&$5*0/ (306/%$-".14 /&$/"5*0/"-&-&$53*$"-$0%& I 108&34&37*$&(306/%*/( &-&$530%&4:45&. /&$"35 1"35) 13. Power-Cord Protection – Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product. 15. Outdoor Antenna Grounding – If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. See Figure A. 16. Lightning – For added protection for this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the product due to lightning and power-line surges. 17. Power Lines – An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal. 18. Overloading – Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock. 19. Object and Liquid Entry – Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product. 20. Servicing – Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel. 21. Damage Requiring Service – Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions: a)When the power-supply cord or plug is damaged, b)If liquid has been spilled, or objects have fallen into the product, c) If the product has been exposed to rain or water, d)If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation, e)If the product has been dropped or damaged in any way, and f)When the product exhibits a distinct change in performance – this indicates a need for service. 22. Replacement Parts – When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards. 23. Safety Check – Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition. 24. Wall or Ceiling Mounting – The product should be mounted to a wall or ceiling only as recommended by the manufacturer. 25.Heat – The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat. FRANCAIS ENGLISH FCC INFORMATION (For US customers) n NOTE ON USE / OBSERVATIONS RELATIVES A L’UTILISATION 1. PRODUCT This product complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this product may not cause harmful interference, and (2) this product must accept any interference received, including interference that may cause undesired operation. 2. IMPORTANT NOTICE: DO NOT MODIFY THIS PRODUCT This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modification not expressly approved by DENON may void your authority, granted by the FCC, to use the product. 3. NOTE This product has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This product generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this product does cause harmful interference to radio or television reception, which can be determined by turning the product OFF and ON, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the product into an outlet on a circuit different from that to which the receiver is connected. • Consult the local retailer authorized to distribute this type of product or an experienced radio/TV technician for help. • Keep the unit free from moisture, water, and dust. • Protéger l’appareil contre l’humidité, l’eau et la poussière. • Do not let foreign objects into the unit. • Ne pas laisser des objets étrangers dans l’appareil. • Avoid high temperatures. Allow for sufficient heat dispersion when installed in a rack. • Eviter des températures élevées. Tenir compte d’une dispersion de chaleur suffisante lors de l’installation sur une étagère. This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. • Do not let insecticides, benzene, and thinner come in contact with the unit. • Unplug the power cord when not using the • Ne pas mettre en contact des insecticides, du benzène et un diluant avec l’appareil. unit for long periods of time. • Débrancher le cordon d’alimentation lorsque l’appareil n’est pas utilisé pendant de longues périodes. • Handle the power cord carefully. Hold the plug when unplugging the cord. • Manipuler le cordon d’alimentation avec précaution. Tenir la prise lors du débranchement du cordon. * (For apparatuses with ventilation holes) • Do not obstruct the ventilation holes. • Ne pas obstruer les trous d’aération. • Never disassemble or modify the unit in any way. • Ne jamais démonter ou modifier l’appareil d’une manière ou d’une autre. II ENGLISH n Contents Getting Started Accessories······················································································2 Cautions on Handling······································································3 Cautions on Installation··································································3 About the Remote Control Unit·····················································3 Inserting the Batteries····································································3 Operating Range of the Remote Control Unit·································3 Part Names and Functions·····························································4 Front Panel······················································································4 Display····························································································4 Rear Panel·······················································································5 Remote Control Unit·······································································6 Connections Preparations·····················································································7 Cables Used for Connections·························································7 Video Conversion Function·····························································8 Speaker Connections······································································8 Speaker Installation·········································································8 Speaker Connections······································································9 Connecting Equipment with HDMI connectors··························10 Connecting the Monitor································································11 Connecting the Playback Components·······································11 DVD Player····················································································11 CD Player······················································································12 iPod®· ···························································································12 TV/CABLE Tuner···········································································13 Connecting the Recording Components·····································13 Video Cassette Recorder······························································13 CD Recorder / MD Recorder / Tape Deck·····································14 Connections to Other Devices······················································14 Video Camera / Game Console·····················································14 Component with Multi-channel Output connectors······················ 14 SIRIUS connector··········································································15 Antenna terminals · ······································································16 Multi-zone·····················································································17 Connecting the Power Cord·························································17 Once Connections are Completed···············································17 Operations Menu Map······················································································18 Examples of Front Display····························································18 Auto Setup Preparations···················································································19 Auto Setup·····················································································20 a Auto Setup···············································································20 s Error Messages·······································································21 System Setup System setup operation·······························································22 Example of Display of Default Values·········································22 1. Speaker Setup···········································································23 a ~ h Speaker Configuration······················································23 j Subwoofer Mode Setup··························································23 k ~ A5 Distance···········································································24 A6 ~ S1 Crossover Frequency·······················································24 S2 Test Tone·················································································24 S3 Restore··················································································· 25 2. Input Setup················································································25 a ~ d HDMI In Assign································································25 f ~ j Digital In Assign·······························································26 k iPod Assign··············································································26 l ~ A1 Component In Assign·······················································26 A2 ~ A5 Video Convert···································································26 A6 Audio Delay··············································································26 A7 EXT. IN Subwoofer Level·························································27 A8 Auto Preset Memory·······························································27 A9 Parental Lock············································································27 S0 Edit Lock Code·········································································27 3. Option Setup··············································································28 a Amp Assign·············································································28 s ~ f Volume Control································································28 g ~ j ZONE2 Volume Control····················································28 k ~ A4 2ch Direct/Stereo Custom···············································29 A5 Auto Surround Mode·······························································30 A6 Direct Mode Setup··································································30 A7 Remote ID Setup·····································································30 Surround Modes q Standard Playback····································································31 Surround Playback of 2-channel Sources······································31 Playing Multi-channel Sources (Dolby Digital, DTS, etc.)··············31 w DSP Simulation Playback·························································32 e Direct Playback··········································································32 r Stereo Playback········································································32 Parameter Adjusting the parameters·····························································33 Surround Parameter······································································33 a Mode·······················································································34 s Cinema EQ···············································································34 d D.Comp (Dynamic Range Compression)·································34 f LFE···························································································34 g Center Image···········································································34 h Panorama·················································································34 j Dimension················································································34 k Center Width···········································································34 l Delay Time···············································································34 A0 Effect Level··············································································34 A1 Room Size················································································34 A2 SB CH OUT··············································································35 A3 SW ATT····················································································35 A4 Subwoofer···············································································35 A5 Tone Control············································································35 A6 Bass·························································································35 A7 Treble·······················································································35 A8 MultEQ····················································································35 A9 Dynamic EQ·············································································36 S0 Dynamic Volume······································································36 S1 DV Setting (Dynamic Volume Setting)·····································36 S2 RESTORER··············································································37 S3 Night Mode··············································································37 S4 Default·····················································································37 Information· ······································································· 38 ENGLISH Troubleshooting······························································ 63 Specifications··································································· 66 List of preset codes· ·························· End of this manual Accessories Check that the following parts are supplied with the product. q Owner’s manual....................................................................... 1 w Getting Started......................................................................... 1 e Warranty (for North America model only)................................. 1 r Service station list.................................................................... 1 t Main remote control (RC-1098)................................................ 1 y R6/AA batteries (for RC-1098).................................................. 2 u Sub remote control (RC-1108).................................................. 1 i R03/AAA batteries (for RC-1108).............................................. 2 o FM indoor antenna................................................................... 1 Q0 AM loop antenna...................................................................... 1 Q1 Setup microphone Multi-Zone (DM-A409, Cord length: Approx. 25 ft / 7.6 m)........................ 1 t u Q0 Troubleshooting o Information Other Operations···········································································45 Recording on an External Device (REC OUT mode)·····················45 Convenient Functions···································································45 Channel Level···············································································45 Quick Select Function···································································46 Personal Memory Plus Function···················································46 Last Function Memory··································································46 Backup Memory············································································46 Resetting the Microprocessor······················································46 Other Information· ························································ 55 Thank you for purchasing this DENON product. To ensure proper operation, please read this owner’s manual carefully before using the product. After reading them, be sure to keep them for future reference. Playback Remote Control Other Operations and Functions Multi-zone Settings with the Amp Assign Function··················51 Multi-zone Settings and Operations with Zone Output············53 Multi-zone Operations··································································54 Turning the Power On and Off······················································54 Selecting the Input Source····························································54 Adjusting the Volume····································································54 Turning off the Sound Temporarily···············································54 Getting Started Setup Preparations···················································································39 Turning the Power On···································································39 Selecting the Input Source····························································39 Setting the Input Mode·································································39 Operations During Playback··························································40 Playing Video and Audio Equipment···········································40 Basic Operation·············································································40 Listening to FM/AM Broadcasts··················································40 Basic Operation·············································································40 Presetting Radio Stations (Preset Memory)··································41 Listening to Preset Stations··························································41 Listening to SIRIUS Satellite Radio Programs····························42 Basic Operation·············································································42 Checking the SIRIUS Signal Strength and Radio ID······················42 Searching Categories····································································42 Parental Lock·················································································42 iPod® Playback··············································································43 Preparations··················································································43 Listening to Audio·········································································44 Viewing Still Pictures or Videos on the iPod·································44 Amp Assign / Multi-zone Connections and Operations Getting Started Connections Playback Q1 Remote Control Unit Operations Main Remote Control Unit (RC-1098)··········································47 Operating DENON Audio Components·········································47 Presetting······················································································47 Operating Preset Components·····················································47 Punch Through Function·······························································50 Sub Remote Control Unit (RC-1108)············································50 ENGLISH Getting Started Connections Cautions on Handling About the Remote Control Unit • Before turning the power switch on Check once again that all connections are correct and that there are no problems with the connection cables. • Power is supplied to some of the circuitry even when the unit is set to the standby mode. When traveling or leaving home for long periods of time, be sure to unplug the power cord from the power outlet. Setup Playback Remote Control • About condensation If there is a major difference in temperature between the inside of the unit and the surroundings, condensation (dew) may form on the operating parts inside the unit, causing the unit not to operate properly. If this happens, let the unit sit for an hour or two with the power turned off and wait until there is little difference in temperature before using the unit. In addition to the AVR-1709, the included main remote control unit (RC-1098) can also be used to operate the equipment listed below. q DENON system components w Non-DENON system components • By setting the preset memory (vpage 47 ~ 49) Inserting the Batteries q Lift the clasp and remove the rear cover. (RC-1098) (RC-1108) • Cautions on using mobile phones Using a mobile phone near this unit may result in noise. If so, move the mobile phone away from this unit when it is in use. Multi-Zone • Moving the unit Turn off the power and unplug the power cord from the power outlet. Next, disconnect the connection cables to other system units before moving the unit. Information • Note that the illustrations in these instructions may differ from the actual unit for explanation purposes. w Load the two batteries properly as indicated by the marks in the battery compartment. (RC-1098) NOTE • Replace the batteries with new ones if the set does not operate even when the remote control unit is operated close to the unit. • The supplied batteries are only for verifying operation. • When inserting the batteries, be sure to do so in the proper direction, following the “q” and “w” marks in the battery compartment. • To prevent damage or leakage of battery fluid: • Do not use a new battery together with an old one. • Do not use two different types of batteries. • Do not attempt to charge dry batteries. • Do not short-circuit, disassemble, heat or dispose of batteries in flames. • If the battery fluid should leak, carefully wipe the fluid off the inside of the battery compartment and insert new batteries. • Remove the batteries from the remote control unit if it will not be in use for long periods. • When replacing the batteries, have the new batteries ready and insert them as quickly as possible. Operating Range of the Remote Control Unit Point the remote control unit at the remote sensor when operating it. (RC-1108) R6/AA R03/AAA (RC-1108) Troubleshooting Cautions on Installation 30° Note: For proper heat dispersal, do not install this unit in a confined space, such as a bookcase or similar enclosure. 30° e Put the rear cover back on. Approx. 23 feet / 7 m b Note (RC-1098) b b NOTE The set may function improperly or the remote control unit may not operate if the remote control sensor is exposed to direct sunlight, strong artificial light from an inverter type fluorescent lamp or infrared light. b Wall or ENGLISH For buttons not explained here, see the page indicated in parentheses ( ). Front Panel W7 W6 W5 W4 W3 W2 W1 E4 Q5 E5 E6 E7 bAbout Dynamic Volume Audyssey Dynamic Volume™ solves the problem of large variations in volume level between television programs, commercials, and between the soft and loud passages of movies. Audyssey Dynamic EQ™ is integrated into Dynamic Volume so that as the playback volume is adjusted automatically, the perceived bass response, tonal balance, surround impression, and dialog clarity remain the same. bAbout Dynamic EQ Audyssey Dynamic EQ solves the problem of deteriorating sound quality as volume is decreased by taking into account human perception and room acoustics. Audyssey Dynamic EQ works in tandem with Audyssey MultEQ® to provide wellbalanced sound for every listener at any volume level. E7 VIDEO SELECT button································ (40) Display w e r ty u i o Q0 Q1 Q2 Q3 Q4 i q Power operation button uy t Multi-Zone q r Q3 SELECT/ENTER knob (ON/STANDBY)··········································· (39) Q0 SETUP MIC jack··········································· (19) Q1 SYSTEM SETUP button······························ (22) Q2 SURR. MODE / SURR. PARA button····· (31, 33) q w q Signal channel indicator • The control functions in the same way as the cursor o button when turned counterclockwise, as the cursor p button when turned clockwise. • The control functions in the same way as the ENTER button when pressed the knob. Q4 Cursor buttons (ui)·································· (22) Q5 MASTER VOLUME control knob················ (40) Q6 Dynamic Volume indicator························· (36) Q7 MultEQ indicator········································· (35) Q8 Master volume indicator Q9 SURROUND BACK indicator Lights when the preset channel is displayed at w. w Information display e Input signal indicators r Master volume indicator This displays the volume level. The Setup item number is displayed in System Setup. t ZONE2/REC OUT source indicators These indicators indicate the input source being output to “ZONE2/REC OUT”. y REC SELECT indicator This lights when the REC OUT mode is selected. (This indicator is off when “SOURCE” is selected.) e u ZONE2 indicator This lights when the ZONE2 mode is selected. (This indicator is off when “SOURCE” is selected.) i Tuner reception mode indicators These light according to the reception conditions when the input source is set to “TUNER”. • AUTO This lights when in the auto tuning mode. • STEREO In the FM mode, this lights when receiving analog stereo broadcasts. • TUNED This lights when the broadcast is properly tuned in. Troubleshooting Remove the cap covering the connectors when you want to use them. • The SELECT/ENTER knob on the main unit operates in the same way as the cursor o and p buttons on the main remote control unit. Information w Power indicator··········································· (39) e Power switch (hON jOFF)················ (39, 46) r Headphone jack (PHONES)························· (40) t INPUT MODE button··································· (39) y SPEAKERS button································· (40, 46) u ZONE2 ON/OFF button······························· (54) i QUICK SELECT buttons······························ (46) o V. AUX INPUT connectors Playback Remote Control E3 Q8 Q7 Q6 E6 DYNAMIC VOLUME button························ (36) Setup W8 W9 E0 E1 E2 W0 Q9 W0 INPUT mode indicators······························· (39) W1 SIGNAL indicators W2 Display W3 SPEAKERS indicators·································· (40) W4 Remote control sensor································· (3) W5 ZONE2/REC SELECT button······················· (45) W6 SOURCE SELECT knob······························· (39) W7 SOURCE button··········································· (39) W8 STATUS button··········································· (38) W9 DIMMER button··········································· (40) E0 RESTORER button······································· (37) E1 BAND button··············································· (40) E2 SHIFT button················································ (41) E3 PRESET CHANNEL buttons (df)··············· (41) E4 TUNING buttons (df)································· (40) E5 MULTEQ button·········································· (35) Getting Started Connections Part Names and Functions ENGLISH Getting Started Connections Rear Panel Q5 Q4 Q3 Q2 Q1 Q0 o Setup Playback Remote Control Multi-Zone Information Troubleshooting q w q Digital audio connectors (OPTICAL / COAXIAL)··················· (10 ~ 13, 15) w VIDEO / S-VIDEO connectors············· (11 ~ 13) e Analog audio connectors (AUDIO)·········································· (10 ~ 14, 17) r EXT. IN connectors······································ (14) t REMOTE CONTROL jacks··························· (17) y PRE OUT connector······································· (9) e r t u ZONE2 connectors······································ (17) i AC OUTLETS················································ (17) o Power cord··················································· (17) Q0 Speaker terminals (SPEAKERS)······· (9, 51, 52) Q1 FM/AM antenna terminals (TUNER ANTENNA)····································· (16) Q2 COMPONENT VIDEO connectors··········(11, 13) y u Q3 HDMI connectors······························ (10, 11, 13) Q4 SIRIUS connector (SAT TU)························· (15) Q5 DOCK CONTROL jack·································· (12) i ENGLISH q ZONE2 power buttons································ (54) w Source select buttons··························· (39, 54) n Main remote control unit (RC-1098) b : To select “SIRIUS” as the input source, use the SAT TU button. [ Front ] Q1 q w b t y Q4 u Q5 Q6 u r t q w “CD”, “iPod/NETWORK” or “TUNER” “ZONE2” “AUDIO” b e Q0 r Q1 t y u NOTE i o n When operating ZONE2 If buttons on the front or rear are pressed strongly, the button on the opposite side will be activated too. Q2 nSub remote control unit for ZONE2 (RC-1108) n When operating MAIN ZONE “AUDIO” i o Q0 Q1 SOURCE CONTROL switch settings and operable buttons Q0 b Q2 Q3 q Remote control signal transmitter w Zone power off button (OFF)··············· (50, 54) e CHANNEL buttons······································· (50) r TUNING buttons·········································· (50) t System buttons··········································· (50) y REPEAT button············································ (50) u RANDOM button········································· (50) i Zone power on button (ON)················· (50, 54) o Source select buttons··························· (50, 54) b : To select “SIRIUS” as the input source, use the SAT TU button. Q0 Volume control buttons (VOLUME)···· (50, 54) Q1 Muting button (MUTE)························· (50, 54) Q2 SHIFT button················································ (50) Q3 FAVORITES DIRECT PLAY button·············· (50) NOTE The DTU button cannot be used. NOTE With this setting, only ZONE2 buttons can be operated. See page 54 for operable buttons. The FAVORITES DIRECT PLAY button can function when the control dock for iPod ASD-3N or ASD-3W is used. Troubleshooting i o ENTER button········································ (22, 45) e Information Q3 t System buttons····································· (44, 48) y AUDIO DELAY button································· (26) u Cursor buttons (uio p)·························· (22) i DYNAMIC VOLUME button························ (36) o RESTORER button······································· (37) Q0 SOURCE CONTROL switches····················· (40) Q1 Remote control signal transmitter Q2 Master volume control buttons··········· (40, 54) Q3 MUTING button····································· (40, 54) Q4 NIGHT button·············································· (37) Q5 MULTEQ button··········································· (35) Q6 Channel select (CH SEL) / Multi-Zone Q2 w b : To select “SIRIUS” as the input source, use the SAT TU button. e Video select button (V.SEL)······················· (40) r Tuner system buttons··························· (40, 41) t Test tone button (TEST)····························· (25) y Main zone power buttons (MAIN)············· (54) u Surround mode buttons······················· (31, 32) i System setup button (SYSTEM)················ (22) o Surround parameter button (PARA)···· (31, 33) Q0 Enter button (ENT)······································ (22) Q1 Input mode button (INPUT)························ (39) Q2 Cursor buttons (uio p)·························· (22) Playback Remote Control r y Setup e q q Indicator······················································· (47) w Power buttons············································· (39) e QUICK SELECT buttons······························ (46) r Source select buttons··························· (39, 54) Getting Started Connections [ Rear ] Remote Control Unit ENGLISH Getting Started Connections Connections Connections for all compatible audio and video signal formats are described in this owner’s manual. Please select the types of connections suited for the equipment you are connecting. With some types of connections, certain settings must be made on the AVR-1709. For details, refer to the instructions for the respective connection items below. Setup NOTE Playback Remote Control • Do not plug in the power cord until all connections have been completed. • When making connections, also refer to the operating instructions of the other components. • Be sure to connect the left and right channels properly (left with left, right with right). • Do not bundle power cords together with connection cables. Doing so can result in humming or noise. Preparations Cables Used for Connections Select the cables according to the equipment being connected. Audio cables Video cables Coaxial digital connections Component video connections (Green) (Orange) (Blue) Coaxial digital (75 Ω/ohms pin-plug) cable (PB/CB) (Red) Optical digital connections (PR/CR) Component video cable S-Video connections Optical cable Multi-Zone Analog connections (stereo) (White) L L (Red) R R S-Video cable Video connections Information Stereo pin-plug cable (Yellow) 75 Ω/ohms pin-plug video cable Analog connections (monaural, for subwoofer) Troubleshooting (Black) Pin-plug cable (Y) Audio and video cables HDMI connections Speaker connections 19-pin HDMI cable Speaker cables Signal direction Audio signal: Video signal: Output Input Output Input Input Output Input Output ENGLISH • This function automatically converts various formats of video signals input to the AVR-1709 into the format used to output the video signals from the AVR-1709 to a monitor. • The AVR-1709’s video input/output circuitry is compatible with the following four types of video signals: Digital video signals: HDMI Analog video signals: Component video, S-Video and Video Speaker Installation The illustration below shows a basic example of installation of the amplifier combined with 8 speakers and a monitor. GFlow of video signals inside the AVR-1709H Center speaker Digital video signals HDMI connector Component video connectors Component video connectors S-Video connector S-Video connector Video connector Video connector Video input terminals Monitor output terminals Playback Remote Control HDMI connector Surround back speakers Monitor Analog video signals Front speakers Place the front speakers to the sides of the monitor or screen and as flush with the screen surface as possible. Surround speakers Information The table below shows a typical speaker configuration for the AVR-1709. FRONT A / B L R 7.1-channels S S 6.1-channels S S 5.1-channels S 3.1-channels S 2.1-channels 2-channels CENTER SURROUND SURROUND BACK 1 speaker SUBWOOFER L R L R S S S S S – S S S S – – S S S S S S – – – S S S – – – – – S S S – – – – – – S S S – – – – – – – Troubleshooting NOTE • Analog video signal cannot be converted to HDMI signals. • Component input video signals cannot be output to anything other than component video connectors. • When a non-standard video signal from a game machine or some other source is input, the video conversion function might not operate. Multi-Zone When not using this function, connect a monitor output with the same type of connector as the video input connector. Setup High picture quality playback Subwoofer Getting Started Connections Speaker Connections Video Conversion Function ENGLISH Getting Started Connections Connecting the Speaker Cables Speaker Connections Example: 5.1-channels Subwoofer Front speakers A Subwoofer with built-in amplifier (L) Setup w Center speaker Carefully check the left (L) and right (R) channels and + (red) and – (black) polarities on the speakers being connected to the AVR-1709, and be sure to interconnect the channels and polarities correctly. 1 Peel off about 0.03 ft/10 mm of sheathing from the tip of the speaker cable, then either twist the core wire tightly or terminate it. 2 Turn the speaker terminal counterclockwise to loosen it. 3 Insert the speaker cable’s core wire to the hilt into the speaker terminal. 4 Turn the speaker terminal clockwise to tighten it. (R) q w q w */ q Playback Remote Control Multi-Zone When using a banana plug Information Tighten the speaker terminal firmly before inserting the banana plug. Troubleshooting b L : Left R : Right (L) w (R) qw q Surround speakers NOTE For surround back speakers : •By default, the AVR-1709’s “Amp Assign” setting is set to “ZONE2”. To use as the surround back speaker for the main zone, change the “Amp Assign” setting (vpage 28). •When using just one surround back speaker, connect it to the left channel (SBL). For ZONE2 speakers : •For multi-zone connection and operation, see “Amp Assign / Multi-zone Connections and Operations” (vpage 51 ~ 53). NOTE • Use speakers with an impedance of 6 to 16 Ω/ohms. When using front A and B speakers simultaneously, use speakers with an impedance of 12 to 16 Ω/ohms. • Connect the speaker cables in such a way that they do not stick out of the speaker terminals. The protection circuit may be activated if the core wires touch the rear panel or if the + and – sides touch each other (v“Protection circuit”). • Never touch the speaker terminals while the power supply is connected. Doing so could result in electric shock. Protection circuit If the core wires touch the rear panel and the screws etc., or the ± sides touch each other, the protection circuit will be activated and the power indicator will flash red at intervals of 0.5 secs. If the protection circuit is activated, the speaker output is isolated, and the power supply goes to the standby state. If the power supply is turned off, after the power supply cord is withdrawn, please confirm that speaker cable and input cable are connected. Also, if replaying large sound levels by using a speaker having an impedance less than that specified (eg, 4 Ω/ohms), the temperature will rise, and the protection circuit might be activated. The power supply will go into the standby state, and the power indicator will flash red at 2 second intervals. In this case, please switch off the power supply, and wait until the AVR-1709 has cooled down, and the surrounding ventilation is good. Even if there are no problems with the surrounding ventilation and connections, in the event of the protection circuit becoming activated, due to thinking that the AVR-1709 has failed, please contact DENON Service center after switching off. ENGLISH DVD player Monitor "6%*0 "6%*0 065 3 $0"9*"065 )%.* 065 )%.* */ When HDMI input signals are sent to the monitor as HDMI output, both video and audio are output to the monitor. NOTE L • The audio and video signals input to the AVR-1709’s HDMI input connector are output unchanged from the HDMI output connector. Because of this, the sound is output from the monitor connected using the HDMI connectors, but in order to take full advantage of the AVR-1709’s playback sound, turn the TV’s volume down. • If the connected monitor or DVD player only has a DVI-D connector, use an HDMI/DVI converter cable. When using a DVI cable, no audio signals are transmitted. • Use a Deep Color compatible cable for connection to Deep Color compatible devices. When connecting with an HDMI/DVI converter cable (adapter) Multi-Zone • HDMI video signals are theoretically compatible with the DVI format. When connecting to a monitor, etc., equipped with a DVI-D connector, connection is possible using an HDMI/DVI converter cable, but depending on the combination of components in some cases the video signals will not be output. • When connecting using an HDMI/DVI converter adapter, the video signals may not be output properly due to poor connections with the connected cable, etc. Playback Remote Control R The audio signal input to the HDMI input connector cannot be played on the AVR-1709. Input the audio signal to the digital audio input connector or analog audio input connector. Setup L R NOTE • The AVR-1709 cannot be controlled from another device via the HDMI cable. • Video signals are not output if the input video signals do not match the monitor’s resolution. In this case, switch the DVD player’s resolution to a resolution with which the monitor is compatible. • Use a cable on which the HDMI logo is indicated (a certified HDMI product) for connection to the HDMI connector. Normal playback may not be possible when using a cable other than one on which the HDMI logo is indicated (a non-HDMI-certified product). • If the monitor or DVD player does not support Deep Color, deep color signal transfer is not possible. • If the monitor or DVD player does not support xvYCC, xvYCC signal transfer is not possible. Getting Started Connections Connecting Equipment with HDMI connectors Information Troubleshooting b The AVR-1709 is equipped for HDMI version 1.3a. This version is compatible with other versions, allowing connection to all components equipped with an HDMI connector. b The AVR-1709 is compatible with 30- and 36-bit Deep Color. b The AVR-1709 can be connected to a device equipped with an HDMI output connector using an HDMI cable. b The AVR-1709 is compatible with HDMI Ver. 1.3a Deep Color and xvYCC. 10 ENGLISH Getting Started Connections Connecting the Monitor Connecting the Playback Components Select the terminal to use and connect the device (vpage 8 “Video Conversion Function”). Carefully check the left (L) and right (R) channels and the inputs and outputs, and be sure to interconnect correctly. Monitor 7*%&0 47*%&0 */ 7*%&0 */ $0.10/&/57*%&0 */ : 1# 13 )%.* */ DVD Player Select the terminal to use and connect the device. Setup DVD player NOTE "6%*0 Playback Remote Control "6%*0 065 3 L R L R $0"9*"065 7*%&0 )%.* 065 $0.10/&/57*%&0 065 : 1# 13 7*%&0 065 47*%&0 065 The audio signal input to the HDMI input connector cannot be played on the AVR-1709. Input the audio signal to the digital audio input connector or analog audio input connector. Multi-Zone Information Troubleshooting NOTE • Video/S-Video or Component Video connections are required to playback analog video devices on TV monitor. • The component video connectors may be indicated differently on your monitor. For details, see the monitor’s operating instructions. • To play the sound by AVR-1709, make analog or digital audio output connections to AVR-1709’s audio input connectors. • The signals output from the HDMI connectors are only the HDMI input signals. 11 • The same method can be used to connect an HDP (High-Definition Player) such as a Blu-ray Disc player. • When using a optical cable for the digital audio connection, make the settings at “System Setup” – “Input Setup” – “Digital In Assign” (vpage 26). ENGLISH iPod® Select the terminal to use and connect the device. CD player Use a DENON control dock for iPod (ASD-1R, ASD-11R, ASD-3N or ASD-3W, sold separately) to connect the iPod to the AVR-1709. For instructions on the control dock for iPod settings, refer to the control dock for iPod’s operating instructions. "6%*0 $0"9*"065 iPod "6%*0 065 3 L R "4%/8 R L R L Playback Remote Control R Setup L Getting Started Connections CD Player Multi-Zone Information Troubleshooting When using a coaxial cable for the digital audio connection, make the settings at “System Setup” – “Input Setup” – “Digital In Assign” (vpage 26). • With the default settings, the iPod can be used connected to the VCR (iPod) connector. • To assign the iPod to a connector other than VCR (iPod), make the settings at “System Setup” – “Input Setup” – “iPod Assign” (vpage 26). NOTE Video/S-Video or Component Video connections are required to playback iPod Video or Photos on TV monitor. 12 ENGLISH Getting Started Connections Connecting the Recording Components TV/CABLE Tuner Select the terminal to use and connect the device. TV tuner NOTE "6%*0 "6%*0 065 3 Setup L R 015*$"065 7*%&0 )%.* 065 $0.10/&/57*%&0 065 : 1# 13 7*%&0 065 47*%&0 065 The audio signal input to the HDMI input connector cannot be played on the AVR-1709. Input the audio signal to the digital audio input connector or analog audio input connector. Carefully check the left (L) and right (R) channels and the inputs and outputs, and be sure to interconnect correctly. Video Cassette Recorder Select the terminal to use and connect the device. Video cassette recorder 7*%&0 Playback Remote Control 7*%&0 */ L R 47*%&0 */ "6%*0 "6%*0 */ 3 7*%&0 7*%&0 065 47*%&0 065 "6%*0 "6%*0 065 3 L R L R L R L R Multi-Zone Information Troubleshooting When using a optical cable for the digital audio connection, make the settings at “System Setup” – “Input Setup” – “Digital In Assign” (vpage 26). • When recording via the AVR-1709, the playback device’s cable must be of the same type as the cable used to connect the AVR-1709’s VCR OUT connector. Example: TV IN → S-Video cable : VCR OUT → S-Video cable TV IN → Video cable : VCR OUT → Video cable • When using a component video cable for the video connection, make the settings at “System Setup” – “Input Setup” – “Component In Assign” (vpage 26). 13 ENGLISH Select the terminal to use and connect the device. CD recorder / MD recorder / Tape deck "6%*0 "6%*0 */ 3 R L L R Select the terminal to use and connect the device. DVD player / External decoder Video Camera / Game Console Select the terminal to use and connect the device. Video camera / Game console 7*%&0 "6%*0 7*%&0 065 "6%*0 065 3 R L R L R "6%*0 46# 800'&3 '30/5 - 3 $&/5&3 463306/% - 3 463306/% #"$, - 3 L R L R L R L R L R L R Playback Remote Control L R Carefully check the left (L) and right (R) channels and the inputs and outputs, and be sure to interconnect correctly. Component with Multi-channel Output connectors Setup L "6%*0 065 3 Connections to Other Devices Getting Started Connections CD Recorder / MD Recorder / Tape Deck Multi-Zone Information 14 Troubleshooting • To play the analog input signals input to the EXT. IN connectors, press the INPUT MODE button on the main unit or the INPUT button on the main remote control unit and select “EXT. IN” (vpage 39). • The video signal can be connected in the same way as a DVD player (vpage 11). • To play copyright-protected discs, connect the AVR-1709’s EXT. IN connector with the DVD player’s analog multi-channel output connector. ENGLISH Getting Started Connections SIRIUS connector • The AVR-1709 is a SIRIUS Satellite Radio Ready® receiver. You can receive SIRIUS® Satellite Radio by connecting to the SiriusConnect Home Tuner and subscribing to the SIRIUS service. • Plug the SIRIUS connector on the rear panel. • Position the Home Tuner antenna near a south-facing window to receive the best signal. For details, see “Listening to SIRIUS Satellite Radio Programs” (vpage 42). When making connections, also refer to the operating instructions of the SiriusConnect Home Tuner. SiriusConnect Home Tuner When connecting the Optical terminal, set the input Optical terminal allocations for “System Setup” – “Input Setup” – “Digital In Assign”, in “SIRIUS”. NOTE Keep the power cord unplugged until the SiriusConnect Home Tuner connection have been completed. ©2006 SIRIUS Satellite Radio Inc. “SIRIUS”, the SIRIUS dog logo, and channel names and logos are trademarks of SIRIUS Satellite Radio Inc. Setup n Positioning the Antenna Playback Remote Control For a consistent satellite signal, the antenna must be positioned correctly. Use the following map to determine which area you are in and position the antenna accordingly. SKY NORTH b When connecting digital audio. Multi-Zone WEST q t w r EAST e Information SOUTH HORIZON Troubleshooting Area 1 :Point the antenna toward the sky in the east, northeast, or southeast, either through a window or outside. Area 2 :Point the antenna toward the sky in the north or northeast, either through a window or outside. Area 3 :Point the antenna toward the sky in the north or northwest, either through a window or outside. Area 4 :Point the antenna toward the sky in the west, northwest, or southwest, either through a window or outside. Area 5 :Put the antenna outside and point it straight up. The antenna cannot be used indoors. 15 ENGLISH Getting Started Connections Antenna terminals An F-type FM antenna cable plug can be connected directly. Direction of broadcasting station FM antenna Setup AM loop antenna (supplied) 75 Ω/ohms Coaxial cable Playback Remote Control FM indoor antenna (supplied) Multi-Zone Information Connection of AM antennas AM outdoor antenna 1. Push the lever. 2. Insert the conductor. 3. Return the lever. Troubleshooting Ground n AM loop antenna assembly Connect to the AM antenna terminals. Remove the vinyl tie and take out the connection line. a. With the antenna on top of any stable surface. Mount Bend in the reverse direction. b. With the antenna attached to a wall. Installation hole Mount on wall, etc. NOTE • Do not connect two FM antennas simultaneously. • Even if an external AM antenna is used, do not disconnect the AM loop antenna. • Make sure the AM loop antenna lead terminals do not touch metal parts of the panel. Note to CATV system installer: This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC which provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical. 16 ENGLISH Getting Started Connections Connecting the Power Cord Multi-zone Wait until all connections have been completed before connecting the power cord. ZONE2 Out Connections If another pre-main (integrated) amplifier is connected, the ZONE2 out connectors can be used to play a different program source in ZONE2 the same time (vpage 51 ~ 54). Power cord Pre-main amplifier (ZONE2) To household power outlet (AC 120 V, 60 Hz) "6%*0 Setup "6%*0 */ 3 Playback Remote Control L R L R Connection to the AC outlets • These outlets supply power to external audio equipment. • The power supplied from these outlets turns on and off together with the set’s power switch. • Audio equipment with a total power consumption of 120 W (1 A) can be connected. NOTE Multi-Zone • Insert the AC plugs securely. Incomplete connections could cause noise. • Only use the AC outlets to plug in audio equipment. Do not use them as power supplies for hairdryers or anything other than audio equipment. Information Once Connections are Completed Turning the Power On (vpage 39) Troubleshooting "69 065 Infrared retransmitter Input Output Infrared sensor Extension jack for future use. (Connect devices corresponding with room to room function to this jack.) NOTE • For the audio output, use high quality pin-plug cords so that no induction humming or noise is produced. • For instructions on installing and operating separately sold devices, refer to the respective devices’ operating instructions. • To conduct multi-zone playback, see “Amp Assign / Multi-zone Connections and Operations” (vpage 51 ~ 53). 17 ENGLISH Getting Started Connections Operations Menu Map Examples of Front Display Some typical examples are described below. Auto Setup (vpage 19 ~ 21) b When the setup microphone is connected. Currently selected line Menu number Current setting Q 22 T.Tone Yes< Press the o button to select. Currently selected line Information n Option Setup (vpage 28 ~ 30) • Amp Assign • Volume Control · Volume Limit · Power On Level · Mute Level • ZONE2 Volume Control · ZONE2 Volume Limit · ZONE2 Power On Level · ZONE2 Mute Level • 2ch Direct/Stereo • Auto Surround Mode • Direct Mode Setup • Remote ID Setup Multi-Zone n Input Setup (vpage 25 ~ 27) • HDMI In Assign • Digital In Assign • iPod Assign • Component In Assign • Video Convert • Audio Delay • EXT. IN Subwoofer Level • Auto Preset Memory • Parental Lock • Edit Lock Code Playback Remote Control W 1 HDMI1:DVD System Setup (vpage 22 ~ 30) n Speaker Setup (vpage 23 ~ 25) • Speaker Configuration • Subwoofer Mode Setup • Distance • Crossover Frequency • Test Tone • Restore Setup Item number n Start Menu • Step 1: Speaker Detection • Step 2: Measurement • Step 3: Calculation • Step 4: Check • Step 5: Store Troubleshooting Parameter (vpage 33 ~ 37) n Surround Parameter • Mode • Cinema EQ • D. Comp • LFE • Center Image • Panorama • Dimension • Center Width • • • • • • • • Delay Time Effect Level Room Size SB CH OUT SW ATT Subwoofer Tone Control Bass • • • • • • • • Treble MultEQ Dynamic EQ Dynamic Volume DV Setting RESTORER Night Mode Default Information (vpage 38) n Status n Audio Input Signal ENGLISH Getting Started Connections Auto Setup Symbols used to indicate buttons in this manual Setup Button located on both the main unit and the remote control unit BUTTON Button only on the main unit <BUTTON> Button only on the remote control unit [BUTTON] Playback Remote Control MASTER VOLUME ui • Audyssey MultEQ automatically measures the acoustical problems in the listening environment to create the best audio experience for your home theater. • Audyssey MultEQ optimizes a large listening area where one or more listeners are seated. Measurements are performed by placing the calibrated microphone (DM-A409) successively at multiple positions throughout the listening area as shown in Example q. For best results, it is strongly recommended to measure 6 positions so that the measurements have the proper spatial weighting. Even if the listening environment is small as shown in Example w, measuring at multiple points throughout the listening environment results in more effective correction. Example q Example w Multi-Zone ( :Measuring positions) <SPEAKERS> SETUP MIC jack <SETUP MIC> *M 1 2 3 *M Press <SPEAKERS> to select the front speakers Front A, Front B or Front A+B. Set “Amp Assign” to define how the amplifier for the surround back speaker channels is used (vpage 28). Connect the included calibrated setup microphone to the SETUP MIC jack on the main unit. “Auto Set Start” is displayed. Sound receptor 4 ENTER, o Information [Front] Preparations Place the microphone at ear height on a tripod or stand with the microphone pointing directly up towards the ceiling. MASTER VOLUME Troubleshooting About the main listening position (zM) uio ENTER The main listening position refers to the most central position where one would normally sit within the listening environment. MultEQ uses the measurements from this position to calculate speaker distance, level, polarity, and the optimum crossover value for the subwoofer. [Rear] Setup microphone b Do not hold the microphone in your hand during measurements. Be sure that the path from microphone to the speakers is not blocked by objects. Avoid placing the microphone close to a seat back or wall as sound reflections may give inaccurate results. To make manual adjustments to the settings, see pages 23 ~ 25. uio ENTER When using a subwoofer, make the following settings before starting the auto setup procedure: • Defeat the volume and crossover controls if possible • If this is not possible then set • Volume: “12 o’clock” position • Crossover frequency: “Maximum/Highest Frequency” • Low pass filter: “Off” • Standby mode: “Off” ENGLISH • Do not disconnect the setup microphone until the auto setup procedure is completed. • When using headphones, unplug the headphones before starting the auto setup procedure. Auto Setup NOTE The Audyssey MultEQ auto setup function detects the presence of each speaker and automatically calculates the speaker size, channel level, distance, and optimal crossover frequency setting. Audyssey MultEQ corrects acoustical distortions within the listening area. Before starting, connect and position all of your speakers. Once started, MultEQ will play a series of test tones through each speaker. Optimize settings for speakers in use. GAuto setup flowH Step 1: Speaker Detection Step 2: Measurement The speaker connection and polarity are detected at the first measurement position (main listening position). The following attributes are also determined at this time: “Speaker Size”, “Speaker Distance”, “Channel Level”, “Crossover Frequency”. q Press o while “Auto Set<Start” is displayed. • While the measurements are being conducted “Measure:FL <Ccl” (“FL” indicates the speaker being measured) is displayed. • When the measurements are completed, the number of detected speakers is displayed. Example : For a 7.1 channel speaker configuration NOTE • Loud test sounds may be played during Audyssey MultEQ automatic speaker setup. This is part of normal operation. If there is background noise in room, these test signals will increase in volume. • Do not stand between the speakers and setup microphone or allow obstacles in the path while the measurements are being made. This will cause inaccurate readings. • Make the room as quiet as possible. Background noise can disrupt the room measurements. Close windows, silence cell phones, televisions, radios, air conditioners, fluorescent lights, home appliances, light dimmers, or other devices as measurements may be affected by these sounds. Cell phones should be placed away from all audio electronics during the measurement process as Radio Frequency Interference (RFI) may cause measurement disruptions (even if the cell phone is not in use). • Operating MASTER VOLUME during the measurements will cancel the measurements. Number of surround speakers or surround back speakers Number of front speakers or center speakers • To cancel the measurements, press o while “Measure:FL <Ccl” is displayed (“Ccl” stands for “Cancel”). • If the result differs from the actual connection status or an error message appears, use i to display “Retry<” and then press o to repeat the measurement. • If the result still differs from the actual connection status after re-measurement or the error message still appears, it is possible that the speakers are not connected properly. Turn the AVR-1709 off, check the speaker connections and repeat the measurement process from the beginning. The values obtained from the measurements are automatically analyzed and the attributes for each of the speakers in the listening area are determined. q Press o while “Calculate” is displayed. • “Calculating” is displayed and analysis begins. • Analysis takes several minutes to complete. • The time required for this analysis depends on the number of speakers connected. The greater the number of speakers connected, the longer analysis will take. NOTE Do not change the speaker connections or subwoofer volume, or speaker locations after making measurements. If changes are necessary, make the changes and use the Audyssey MultEQ auto setup once again for an updated EQ solution. 0 Troubleshooting Step 5: Store Subwoofer Yes: “.1”, No: “0” Step 3 : Calculation Information Speaker:3/4/.1 Step 4: Check After completing a measurement position, move the microphone to the next position. Measure at 6 positions: the main listening position and 5 other surrounding positions. Although it is allowable to measure less than 6 positions, it is recommended to measure 6 for best results. Multi-Zone Step 3: Calculation Step 1 : Speaker Detection Playback Remote Control The settings found at this stage are applied automatically. Step 2 : Measurement q Press i to select “2nd Start<”, then press o. • The measurement of the 2nd position starts. w Move the microphone to the 3rd position and press o. • The measurement of the 3rd position starts. e Perform w repeatedly. • “Calculate<” is displayed when you have completed measurements in 6 positions. • If you want to stop after measuring just five or fewer positions, use i to display “Calculate<”. Setup a Auto Setup If an error message appears during the measurements, check “Error Messages”, take the advised action, then start the measurements again (vpage 21). Do not change the speaker connections or subwoofer volume after “Step 1”. Getting Started Connections About the Auto Setup NOTE ENGLISH Getting Started Connections Step 4 : Check Setup When analysis is complete, “Parameter Check<” is displayed. Press o and check the analysis results for the following four items. q Make your selection using ui and press o. • Presence and size of speaker “SpConfig. Check<” • Distance of speaker from listening position “Distance Check<” • Speaker channel level “Ch Level Check<” • Crossover Frequency “Crossover Check<” w Use u or i to change which speaker is displayed. s Error Messages If the auto setup procedure could not be completed due to speaker installation, the measuring environment, etc. an error message is displayed. Check the relevant items and be sure to take the necessary measures. After addressing any issues, perform the auto setup procedure over again. Error messages (examples) Mic or Sp:None Playback Remote Control Ambient Noise n To switch to another analysis result item Press ENTER. This returns you to analysis results items, so repeat operation q. n To proceed to “Step 5 : Store” During display of crossover frequency result or analysis results item, press ENTER. • “Store<” is displayed. Caution:Sp None Multi-Zone Information • To proceed to “Step 5” without checking the analysis result, use u i to select “Store<” while “Parameter Check<” is displayed. • Values that are different from the actual distance may be set for speakers with built-in filters (subwoofers, etc). This is because filters add electrical delay to the signal that should be compensated. The messages alternate FR Step 5 : Store Troubleshooting The auto setup measurement results are stored in the AVR-1709. q Press o while “Store<” is displayed. • “Storing” blinks on the display panel while the results are being stored. • When storing is complete, “Completed” is displayed followed by “Disconnect Mic”. w Disconnect the setup microphone from the AVR-1709. Caution:Phase The messages alternate n To cancel storing Use u or i to display “Cancel<” while “Store<” is displayed and press o. • All the measured auto setup data will be erased. SBL Cause • The included setup microphone is not • Connect the included setup connected. microphone to the SETUP MIC jack • Not all speakers could be detected. on the main unit. • Check the speaker connections. • Too much noise in the room for • Either turn off any device generating accurate measurements to be made. noise or move it away. • Try again when the surroundings are quieter. • Speaker or subwoofer sound is too • Check the speaker installation and the low for accurate measurements to be direction in which the speakers are made. facing. • Adjust the subwoofer’s volume. • Displayed speaker could not be • Check the connections of the detected. displayed speaker. · The front L and front R speakers were not properly detected. · Only one channel of the surround speakers was detected. · Sound was output from the R channel when only one surround back speaker was connected. · The surround back speaker was detected, but the surrounds were not detected. • Displayed speaker connected with • Check the polarities of the displayed the polarities reversed. speaker. • For some speakers, this error message may be displayed even if the speaker is properly connected. If the connection is correct, use the u or i buttons to display “Skip<” and then press o. NOTE Do not turn the power off while the settings are being stored. Select “Retry” to make the measurements again. NOTE Measures Be sure to turn the power off before checking speaker connections. ENGLISH Getting Started Connections System Setup Make detail settings for various parameters. Symbols used to indicate buttons in this manual The same operation is possible on the main unit or main remote control unit. 1 2 Press SYSTEM SETUP. “System Setup” is displayed. 3 3 Press o p to select the item you want to set, then press ENTER. 4 5 Press ui to select the item you want to change, then press o p to change the setting. Q Speaker Setup 4 Q 1 Front :Large Example of Display of Default Values In lists of selectable items or adjustable ranges, the item surrounded by a border is the default value. The detailed setup menu for each item is displayed. [Selectable items] Large Small Press ENTER or i to confirm the next settings. Troubleshooting ENTER 1.Sp 2.In 3.Op Information [AUDIO DELAY] uiop 2 n To move to a setup item of another category Press SYSTEM SETUP. [Rear] • Returns to the setup menu. • Perform steps 3 and 4. SYSTEM SETUP [TEST] ENTER uiop Multi-Zone [Front] *System Setup Press ENTER. Three setup menu categories are displayed. “1. Sp” : Speaker Setup “2. In” : Input Setup “3. Op” : Option Setup • The cursor of the item number selected blinks. • For details of the items to be set in each item, see “Menu Map” (vpage 18). ENTER, op 1 Playback Remote Control SYSTEM SETUP ui System setup operation Setup Button located on both the main unit and the remote control unit BUTTON Button only on the main unit <BUTTON> Button only on the remote control unit [BUTTON] n To exit setup Press SYSTEM SETUP while the setup menu is displayed. • The display returns to normal. ENGLISH Getting Started Connections f, g Surround Back Speaker 1. Speaker Setup Use this procedure to set the speakers manually or if you wish to change the settings made with the auto setup procedure. a~h j k ~ A5 A6 ~ S1 S2 S3 Speaker Configuration Subwoofer Mode Setup Distance Crossover Frequency Test Tone Restore Select surround back speaker use and size. [Selectable items] ( Large ( 2spkrs Small 1spkr None ) ) NOTE By default, the AVR-1709’s “Amp Assign” setting is set to “ZONE2”. To use as the surround back speaker for the main zone, change the “Amp Assign” setting (vpage 28). Setup h Subwoofer Playback Remote Control a ~ h Speaker Configuration Select subwoofer use. Select speaker configuration and size. (bass reproduction capability) [Selectable items] [Display] Yes No Large :Select this when using large speakers with ample low frequency reproduction capabilities. 1.Sp 2.In 3.Op Small :Select this when using small speakers without ample low Q frequency reproduction capabilities. Speaker Setup Multi-Zone Q 1 Front :Large Q • Select “Large” or “Small” not according to the physical size of the speaker but according to the low frequency reproduction capabilities based on the frequency set at “Crossover Frequency” (vpage 24). • When “Front Speaker” is set to “Small”, “Subwoofer” is automatically set to “Yes”. • If “Subwoofer” is set to “No”, “Front Speaker” is automatically set to “Large”. • If “Surround Speaker” is set to “None”, “Surround Back Speaker” are automatically set to “None”. • When “Front Speaker” is set to “Small”, “Center Speaker” can not be set to “Large”. • When using just one surround back speaker, connect it to the left channel (SBL). j Subwoofer Mode Setup Select low range signal to be reproduced by subwoofer. [Display] None :Select this when no speaker is connected. Yes :Select this when a subwoofer is connected. No :Select this when no subwoofer is connected. 1.Sp 2.In 3.Op Q Speaker Setup Q Information 6 Subwoofer:Yes 2spkrs 1spkr : Troubleshooting a Front Speaker Select the number of surround back speakers. Select front speaker size. Even when the surround back speaker setting is other than “None”, sound may not be emitted from the surround back speaker, depending on the playback source. In this case, make a “Surround Parameter” – “SB CH OUT” setting other than “OFF” (vpage 35). [Selectable items] Large Small s Center Speaker Select center speaker use and size. [Selectable items] Large Small None d Surround Speaker 7 SW Mode:Norm [Selectable items] Norm :Play low range and LFE signal of channels set to “Small”. +Main :Play low range and LFE signal of all channels. • This can be set when “System Setup” – “Speaker Setup” – “Subwoofer” is set to “Yes”. • Play music or a movie source and select the mode offering the strongest bass. • Select “+Main” if you want the bass signals to always be produced from the subwoofer. Select surround speakers use and size. [Selectable items] 23 Large Small None For details on how to select, set and cancel settings for each menu, see “System setup operation” (vpage 22). ENGLISH A6 ~ S1 Crossover Frequency Set distance from listening position to speakers. Before making the settings, measure the distance from the listening position to the different speakers. Select crossover frequency from which subwoofer handles low range signal. [Display] [Display] 1.Sp 2.In 3.Op 1.Sp 2.In 3.Op Q Speaker Setup Q Speaker Setup Q 8 FL : 12ft Q Q 15 SW : S2 Test Tone Q 12ft 17 Cr.F : 80Hz Adjust channel levels to obtain equal volume from all speakers. F : Front, C : Center, S : Surround, SB : Surround Back, LFE : LFE are displayed. Distance measurement Select the speaker you want to set, then set the distance. Set the value closest to the measured distance. [Display] Only the portion of the bass sound of the various speakers output from the subwoofer that has a frequency below the frequency set here is output. Set this according to the low frequency reproduction capabilities of the speakers you are using. [Variable range] 1.Sp 2.In 3.Op Q Speaker Setup Q 22 T.Tone [Selectable items] NOTE Set the distance between the listening position and the various speakers to no more than 20 ft. 40Hz 60Hz 200Hz 250Hz : 80Hz Yes< Q 90Hz 100Hz 110Hz 120Hz T.Tone 150Hz Auto > Q Test Tone On Set the Crossover Frequency of all speakers as one. Q Auto-FL Set the Crossover Frequency separately for the different speakers. q When “Cr.Over:Adv” is displayed, press ENTER or i. w Press o p to set the crossover frequency of each speaker. The preset speaker changes each time you press i. 60Hz 200Hz 250Hz 80Hz Test Tone Select test tone playback method. [Selectable items] Auto [Selectable items] 90Hz 100Hz 110Hz 120Hz 150Hz Troubleshooting Advanced : 40Hz Information Default setting : • FL / FR / C / SW ··············12 ft • SL / SR / SBL / SBR ········10 ft Multi-Zone 0ft ~ 60ft : Settable in units of 1 foot. Playback Remote Control 16Cr.Over:Adv Setup 16Cr.Over: 80Hz Q • If in the “Advanced” settings, “Subwoofer Mode Setup” (vpage 23) in the “System Setup” is set to “Norm”, it is possible to make this setting for speakers set to “Small” at “Speaker Configuration”. If set to “+Main”, this setting can be made regardless of the speaker size. • For speakers set to “Small”, sound below the crossover frequency is cut from the sound output. The cut bass sound is output from the subwoofer or front speakers. • Always set the crossover frequency to “80Hz”. When using small speakers, however, we recommend setting the crossover frequency to a higher frequency. Getting Started Connections k ~ A5 Distance :Automatically switch speaker from which test tone is output. Manual :Manually switch speaker from which test tone is output. b In the case of “LFE”, there are 8 modes: 80Hz, 90Hz, 100Hz, 110Hz, 120Hz, 150Hz, 200Hz, 250Hz. For details on how to select, set and cancel settings for each menu, see “System setup operation” (vpage 22). 24 ENGLISH Getting Started Connections Test Tone Start Press o to select “Yes”, then press o p to select “Auto” or “Manual”. Then press i. Out put the test tone. Auto : Press o p to adjust the volume. Manual : Press u i to select the speaker, then press o p to adjust the volume. When the adjustments are completed, press ENTER to finish the test tone. Setup [Variable range] –12dB ~ 0dB ~ +12dB S3 Restore After the Auto Setup measurements, it is possible to return those settings to the Auto Setup measurement results after changing the speaker settings (speaker configuration, distance, channel level and crossover frequency) with ”System Setup” – “Speaker Setup”. 2. Input Setup Use this procedure to select the input source and make the settings related to playing input sources. Playback Remote Control a~d f~j k l ~ A1 A2 ~ A5 A6 A7 A8 A9 S0 Press o to start. [Display] 1.Sp 2.In 3.Op Q Operating from the main remote control unit Adjusting with the main remote control unit using the test tones is only possible in the “Auto” mode and only effective in the STANDARD mode. The adjusted levels for the different modes are automatically stored in the memory. Multi-Zone GAdjusting using test tonesH q Press [TEST]. Test tones are output from the various speakers. w Use [o p] to adjust so that the volume is equal for all speakers. e When the adjustments are completed, press [TEST]. Speaker Setup HDMI In Assign Digital In Assign iPod Assign Component In Assign Video Convert Audio Delay EXT. IN Subwoofer Level Auto Preset Memory Parental Lock Edit Lock Code 23 Restore Yes< a ~ d HDMI In Assign It is not possible to return to Amp Assign settings with Restore. After running Auto Setup, if the Amp Assign setting has changed, return to the setting when Auto Setup was run. Select HDMI connector to assign to this source. [Display] 1.Sp 2.In 3.Op W Input Setup W Information Troubleshooting • When “System Setup” – “Speaker Setup” – “Surround Back Speaker” setting (vpage 23) is set to “1spkr”, the surround back speaker display is “SB”. • Speakers set to “None” in the Speaker Configuration settings are not displayed. • When “Channel Level” is adjusted, the adjusted values are set for all the surround modes. 1 HDMI1:DVD W 2 HDMI2:TV [Input terminals] HDMI1 HDMI2 HDMI3 [Assignable input sources] DVD/HDP z1 TV/CBL z2 VCR V.AUX OFF z1 : “DVD” is displayed. z2 : “TV” is displayed. Input terminals a HDMI1 s HDMI2 d HDMI3 Default setting DVD/HDP TV/CBL VCR • With HDMI, the video and audio signals are transferred simultaneously. (The HDMI audio signal is output from the monitor.) At this time, set the input mode to “Auto”. • The audio signals input from the analog, digital and EXT. IN connectors are not output to the monitor. 25 For details on how to select, set and cancel settings for each menu, see “System setup operation” (vpage 22). ENGLISH l ~ A1 Component In Assign Select digital input connector to assign to this source. Select component video input to assign to this source. [Display] [Display] 1.Sp 2.In 3.Op NOTE W W Input Setup W W 9 COMP1 : DVD W [Input terminals] Component video1 Component video2 6 OPT1 : TV OPT1 Component video3 OPT2 CDR DVD/HDP z1 TV/CBL z2 VCR DVD/HDP V.AUX z1 TV/CBL OFF Input terminals Compensate for mismatched timing between video and audio. VCR V.AUX OFF [Display] f COAXIAL1 g COAXIAL2 h OPTICAL1 j OPTICAL2 Default setting DVD/HDP CD TV/CBL VCR Assign control dock for iPod to this source. A0 Component video2 A1 Component video3 DVD/HDP TV/CBL VCR Default setting Automatically convert video input signal to monitor output format. With a movie source, for example, adjust so that the movement of the actors’ lips is synchronized with the sound. Operating from the main remote control unit W Input Setup W W 8 iPod : VCR TV/CBL 12 z2 Press [AUDIO DELAY]. 1.Sp 2.In 3.Op Input Setup z1 ~ 200 ms [Variable range] 0 ms W DVD/HDP 0ms A2 ~ A5 Video Convert 1.Sp 2.In 3.Op CDR W 16A.Delay: Delay audio. This sets the delay time for audio signals. [Display] [Assignable input sources] W Input Setup VCR [Input source] V.AUX DVD/HDP DVD:Conv ON z1 TV/CBL z2 VCR V.AUX • This cannot be adjusted when playing in the EXT. IN, DIRECT or STEREO mode (with “Front Speaker” set to “Large”, “Tone Control” to “OFF” and “MultEQ” to “OFF”). • Store each input source. OFF OFF z1 : “DVD” is displayed. z2 : “TV” is displayed. z1 : “DVD” is displayed. z2 : “TV” is displayed. [Selectable items] With the default settings, the control dock for iPod can be used connected to the VCR (iPod) connector. ON :Enable conversion. OFF :Disable conversion. For details on how to select, set and cancel settings for each menu, see “System setup operation” (vpage 22). 26 Troubleshooting [Display] l Component video1 Information k iPod Assign 1.Sp 2.In 3.Op Multi-Zone Input terminals AUX z2 z1 : “DVD” is displayed. z2 : “TV” is displayed. z1 : “DVD” is displayed. z2 : “TV” is displayed. CD A6 Audio Delay [Assignable input sources] [Assignable input sources] Playback Remote Control [Input terminals] COAX1 COAX2 Setup 4 COAX1 : DVD CD AUX •When a non-standard video signal from a game machine or some other source is input, the video conversion function might not operate. If this happens, please set the conversion mode to “OFF”. • When “Video Convert” is set to “OFF”, the video conversion function does not operate. In this case, connect to a monitor via the same type of terminal as the video input terminal. 1.Sp 2.In 3.Op Input Setup SIRIUS See “Relationship between Video Signals and Monitor Output” (vpage 62) for details of video signal and monitor output relations. Getting Started Connections f ~ j Digital In Assign ENGLISH Getting Started Connections A7 EXT. IN Subwoofer Level A9 Parental Lock S0 Edit Lock Code Set the subwoofer level for playback. Select according to the player in use. For any channel, set the radio reception limits. Change the password (See “Parental Lock”). q Press o. w Using uiop, input the password (4 digits number) and press ENTER. e Set the lock by pressing o p. [Display] 1.Sp 2.In 3.Op [Display] W Input Setup W Setup 1.Sp 2.In 3.Op 17EXT.In SW:+15 Playback Remote Control 0dB +5dB [Display] W [Selectable items] q Press o. w Input old password (4 digits) using uiop, and press ENTER. e Input new password (4 digits) using uiop, and press ENTER. Be sure to memorize the password you have entered. r Input new password (4 digits) again using uiop, and press ENTER. If the correct password is input, “Complete” is displayed, and the new password is modified. Input Setup +10dB : q Select according to the player in use. 1.Sp 2.In 3.Op W W 19ParentalLock< w +15dB : This is the recommended level. Input Setup W Code:[0000] e q W SR001 :<Unlock> w W SR001 :< Lock > Multi-Zone A8 Auto Preset Memory Information Press o to start. • “CH” blinks on the display and searching begins. • “Completed” appears once searching is completed. [Display] 1.Sp 2.In 3.Op Troubleshooting W Input Setup W 18 Preset <Start If an FM station cannot be preset automatically, select the desired station by tuning it in manually, then preset it manually. NOTE “Auto Preset Memory” is displayed when the input source is “FM” and “AM”. 27 r Unlock : Do not lock selected channel(s). Lock W New:[0123] W Repeat:[0123] W :Lock selected channel(s). bWhen a Parental Locked channel is tuned, “Code : [ displayed, then input the password. W Current:[0000] e [Selectable items] Use the auto preset function to program radio stations. W 20EditLockCode< Complete ]” is • The default password is “0000”. If you wish to change this password, set the new password with “Edit Lock Code”. • If the password is incorrectly input, “Incorrect Code” is displayed, and proceed again from step q. • If the password input is 3 digits or less, “Enter 4-digit” is displayed, and input again with a 4 digit password. • While listening to the channel being played, you can also set parental lock (vpage 42). •If the old password is incorrectly input, “Incorrect Code” is displayed, and proceed again from step q. • If the password input is 3 digits or less, “Enter 4-digit” is displayed, and input again with a 4 digit password. • If the new password is not correctly input, “Disagreement” is displayed and the password does not change. NOTE “Edit Lock Code” is displayed when the input source is “SIRIUS”. NOTE “Parental Lock” is displayed when input source is “SIRIUS” , and connected to SIRIUS Tuner. For details on how to select, set and cancel settings for each menu, see “System setup operation” (vpage 22). ENGLISH Make various other settings. a s~f g~j k ~ A4 A5 A6 A7 f Mute Level s ~ f Volume Control This sets the amount of attenuation of the volume when the mute mode is set in the main zone. Set the main zone volume setting. [Display] Amp Assign Volume Control ZONE2 Volume Control 2ch Direct/Stereo Custom Auto Surround Mode Direct Mode Setup Remote ID Setup [Selectable items] Full 1.Sp 2.In 3.Op :The sound is cut off entirely. –40dB :The sound is attenuated by 40 dB. E Option Setup E –20dB :The sound is attenuated by 20 dB. Setup 2 Limit :OFF E 3 P.On : Last E 4 Mute : Full The places where the surround back amplifier are used can be set freely according to the usage environment. This makes it possible to output sound to rooms other than the room (the main zone) where surround playback is performed (multi-zone playback) or play the sound with high quality using the front speakers (bi-amp connections). s Volume Limit Set the ZONE2 volume setting. [Display] Make a setting for maximum volume. 1.Sp 2.In 3.Op [Selectable items] [Display] OFF E Option Setup :Do not set a maximum volume. E –20dB :Set the maximum volume to –20 dB. 5 Z2Limit:OFF E –10dB :Set the maximum volume to –10 dB. E Option Setup 0dB E Multi-Zone 1.Sp 2.In 3.Op 6 Z2 P.On: Last :Set the maximum volume to 0 dB. E d Power On Level [Selectable items] This sets the volume set when the main zone’s power is turned on. :7.1-channel playback FrontA :Bi-amp (5.1-channel playback) FrontB :Bi-amp (5.1-channel playback) Last :Use the memorized setting from the last session. ––– :Always use the muting on condition when power is turned on. [Variable range] For details, see “Amp Assign / Multi-zone Connections and Operations” (vpage 51 ~ 53). g ZONE2 Volume Limit Make a setting for maximum volume. Troubleshooting [Selectable items] ZONE2 :5.1-channel playback + ZONE2 stereo playback Information 7 Z2 Mute:Full 1 Amp:ZONE2 7.1ch g ~ j ZONE2 Volume Control Playback Remote Control a Amp Assign [Selectable items] OFF :Do not set a maximum volume. –20dB :Set the maximum volume to –20 dB. –10dB :Set the maximum volume to –10 dB. –80dB ~ +18dB :Set the volume level when the power is turned on in units of 1 dB. Getting Started Connections 3. Option Setup 0dB :Set the maximum volume to 0 dB. b The variable level when upper limit has been set with “Volume Limit” is “–80 dB ~ the set volume level”. For details on how to select, set and cancel settings for each menu, see “System setup operation” (vpage 22). 28 ENGLISH Getting Started Connections h ZONE2 Power On Level This sets the volume set when the ZONE2’s power is turned on. [Selectable items] Last ––– Select subwoofer use. Make speaker settings for 2-channel mode playback. [Selectable items] [Display] Yes :Use the memorized setting from the last session. 1.Sp 2.In 3.Op :Always use the muting on condition when power is turned on. Setup in units of 1 dB. Norm E 8 2ch Cstm :ON Playback Remote Control E 9 2ch F : Large j ZONE2 Mute Level E 10 2ch SW : Yes This sets the amount of attenuation of the volume when the mute mode is set in the ZONE2. E 11 2ch LFE:Norm [Selectable items] E 12 2ch FL: 12ft :The sound is cut off entirely. A2 Distance FL Set distance from listening position to front left speaker. [Variable range] 0ft ~ 60ft A3 Distance FR Set distance from listening position to front right speaker. Multi-Zone [Variable range] 13 2ch FR: 12ft 0ft ~ 60ft E –20dB :The sound is attenuated by 20 dB. 14 2ch Freq: 80 Information k Setting To change the settings, select “ON”. [Selectable items] Troubleshooting OFF :Use the same settings as in “Speaker Setup”. ON :Make separate settings for 2-channel mode. A4 Crossover Select crossover frequency from which subwoofer handles low range signal. [Selectable items] 40Hz 60Hz 200Hz 250Hz : Select crossover frequency. l Front Select front speaker size. [Selectable items] Large 29 +Main :Select subwoofer signal. E –40dB :The sound is attenuated by 40 dB. “ZONE2 Volume Control” is displayed when “ZONE2” is selected with “Amp Assign” (vpage 28). [Selectable items] 8 2ch Cstm :OFF b The variable level when upper limit has been set with “Volume Limit” is “–70 dB ~ the set volume level”. :Select subwoofer use. Select low range signal to be reproduced by subwoofer. E –70dB ~ +18dB :Set the volume level when the power is turned on No A1 Subwoofer Mode E Option Setup [Variable range] Full A0 Subwoofer k ~ A4 2ch Direct/Stereo Custom Small :Select front speaker size. For details on how to select, set and cancel settings for each menu, see “System setup operation” (vpage 22). 80Hz 90Hz 100Hz 110Hz 120Hz 150Hz ENGLISH A6 Direct Mode Setup Make setting for memorizing surround mode setting for each input signal type. Select MultEQ use for DIRECT mode playback. Getting Started Connections A5 Auto Surround Mode [Display] [Display] 1.Sp 2.In 3.Op 1.Sp 2.In 3.Op E Option Setup E Option Setup E 15AutoSurr.:ON Setup 16 Direct :OFF E [Selectable items] ON :Memorize settings. Most recently stored surround mode is automatically selected. OFF :Do not memorize settings. Surround mode does not change according to input signal. :Use MultEQ. OFF :Do not use MultEQ. A7 Remote ID Setup Set remote control ID. [Display] Multi-Zone 1.Sp 2.In 3.Op E Option Setup Information The auto surround mode function lets you store in the memory the surround mode last used for playing the three types of input signals listed below. q Analog and PCM 2-channel signals (STEREO) w 2-channel signals of Dolby Digital, DTS or other multi-channel format (DOLBY PLgx Cinema) e Multi-channel signals of Dolby Digital, DTS or other multichannel format (DOLBY/DTS SURROUND) b Default settings are indicated in ( ). ON Playback Remote Control [Selectable items] E 17 Remote ID:1 [Selectable items] 1 2 3 4 Troubleshooting NOTE When using the AVR-1709 with only the included remote control unit (RC-1098), there is no need to make settings. When using a separately sold remote control unit (RC-7000CI, etc.), this function can be used. Match the ID setting of the remote control unit and the receiver. For details on how to select, set and cancel settings for each menu, see “System setup operation” (vpage 22). 30 ENGLISH Getting Started Connections Surround Modes Symbols used to indicate buttons in this manual Setup Button located on both the main unit and the remote control unit BUTTON Button only on the main unit <BUTTON> Button only on the remote control unit [BUTTON] Playback Remote Control <SURR. PARA> q Standard Playback This is the mode for enjoying surround sound according to the program source. Surround Playback of 2-channel Sources Selecting the surround mode Select by turning <SELECT/ENTER> or pressing [STD]. [Selectable items] DOLBY PLgx z : The signals are decoded in DOLBY PLgx or DOLBY or PLg for playback. DOLBY PLg DTS NEO:6 Multi-Zone <SELECT/ENTER>, op Information [Front] : The signals are decoded in DTS NEO:6 for playback. z: DOLBY PLgx can be selected when surround back speakers are being used. DOLBY PLg can be selected when surround back speakers are not being used. Select the mode to suit the source Troubleshooting Press <SURR. PARA> or [PARA]. Display “Mode” and select your desired mode using o p. op n DOLBY PLgx or DOLBY PLg [Rear] [D/ST] op [STD] [SIMU] [PARA] Cinema : This mode is suited for movie sources. Music : This mode is suited for music sources. Game : This mode is suited for games. PL : This is the Pro Logic playback mode. This can be selected when playing with a DOLBY PLg decoder. When this mode is selected, “DOLBY PL” is displayed. n DTS NEO:6 Cinema : This mode is suited for movie sources. Music : This mode is suited for music sources. Select the “Cinema”, “Music”, “Game” and “PL” modes at “Surround Parameter” – “Mode” (vpage 34). Playing Multi-channel Sources (Dolby Digital, DTS, etc.) In the case of standard playback of multi channel sources, the AVR1709 recognizes the format of the multi-channel audio input signal and automatically operates the appropriate decoder for surround sound. [Selectable items] STANDARD : Any of the surround modes in the “Display” column in the following table. The mode changes depending upon factors such as the • Input signal • Whether or not surround back speakers are being used. Input signal Dolby Digital Source DOLBY DIGITAL (other than 2ch) / DOLBY DIGITAL EX DTS Surround Source DTS (5.1ch) / DTS-ES Discrete 6.1 / DTS-ES Matrix 6.1 / DTS 96/24 Display DOLBY DIGITAL DOLBY DIGITAL EX DOLBY DIGITAL+PLgx CINEMA DOLBY DIGITAL+PLgx MUSIC DTS SURROUND DTS+PLgx CINEMA DTS+PLgx MUSIC DTS+NEO:6 DTS ES MTRX6.1 (z1) DTS ES DSCRT6.1 (z2) DTS 96/24 (z3) z1 : This is displayed when the input signal is “DTS-ES Matrix 6.1”. z2 : This is displayed when the input signal is “DTS-ES Discrete 6.1”. z3 : This is displayed when the input signal is “DTS 96/24”. • For details, see page 60. • To select these surround modes using <SELECT/ENTER> or press [STD]. ENGLISH The desired mode according to the program source and viewing situation can be selected from among 7 DENON original surround modes. The surround parameters can be adjusted (vpage 58, 59) to achieve an even more realistic, powerful sound field. Selecting the surround mode Select by turning <SELECT/ENTER> or pressing [SIMU]. Selecting the mode Select by turning <SELECT/ENTER> or pressing [D/ST]. [Selectable items] DIRECT : In this mode the signals bypass the tone adjustment circuitry for high quality sound. The sound is output to the same channels as the input signal. Setup [Selectable items] e Direct Playback Getting Started Connections w DSP Simulation Playback from all speakers. ROCK ARENA :This mode is for enjoying the atmosphere of a live concert in an arena. JAZZ CLUB :This mode is for enjoying the atmosphere of a live concert in a jazz club. z2 :This mode is for playing monaural movie MONO MOVIE Display Input signal Analog signal / PCM (2ch) / Dolby Digital source / DTS source / Other 2-channel digital signals Playback Remote Control 5CH / 7CH STEREO z1 :This mode is for enjoying stereo sound DIRECT sources with surround sound. MATRIX :This mode lets you add a sense of expansion to stereo music sources. VIRTUAL :This mode is for enjoying surround effects using only the front speakers or headphones. r Stereo Playback Selecting the mode Select by turning <SELECT/ENTER> or pressing [D/ST]. Troubleshooting z1: “5CH STEREO” is displayed when “Surround Parameter” – “SB CH Out” is set to “OFF”, and “Amp Assign” is set to “ZONE2” (vpage 35). z2: When playing sources recorded in monaural in the MONO MOVIE mode, the sound will be off balance with a single channel (left or right), so input to both channels. For details, see page 61. Information :This mode is suited for achieving surround sound with video games. Multi-Zone VIDEO GAME [Selectable items] STEREO : This is the mode for playing in stereo. The tone can be adjusted. Sound is output from the front left and right speakers and subwoofer. Depending on the program source being played, it may not be possible to achieve a satisfactory surround effect. In this case, try other modes to achieve a sound field suited to your tastes. 32 ENGLISH Getting Started Connections Parameter Symbols used to indicate buttons in this manual Setup Button located on both the main unit and the remote control unit BUTTON Button only on the main unit <BUTTON> Button only on the remote control unit [BUTTON] Playback Remote Control MULTEQ <SURR. PARA> ui Adjusting the parameters 1 2 Press <SURR. PARA> or [PARA]. 3 Use o p to adjust the parameters. Parameter is displayed. Use ui to select which parameters to adjust. Only those parameters which can be adjusted under the current playback status are displayed. Repeat steps 2 and 3 to set each parameter. Surround Parameter Adjust surround sound parameters. The parameters (items) which can be adjusted differ depending upon the following conditions. • Whether an input signal is present (when playing) or not (when stopped, etc.). • The type of input signal • The type of surround mode For details of which parameters can be adjusted in each surround mode, see “Surround Modes and Parameters” (vpage 58, 59). n To exit adjustment • Press <SURR. PARA> or [PARA] during adjustment. • If no adjustment is made for a period of about 5 seconds, the adjustments made up that point are registered and the AVR-1709 returns to the original mode. Multi-Zone RESTORER <DYN VOL.> op Information [Front] Troubleshooting uiop [DYNAMIC VOLUME] [NIGHT] MULTEQ RESTORER [Rear] [CINEMA] [MUSIC] uiop [STD] [PARA] a s d f g h j k l A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 S0 S1 S2 S3 S4 Mode Cinema EQ D. Comp (Dynamic Range Compression) LFE Center Image Panorama Dimension Center Width Delay Time Effect Level Room Size SB CH OUT SW ATT Subwoofer Tone Control Bass Treble MultEQ Dynamic EQ Dynamic Volume DV Setting (Dynamic Volume Setting) RESTORER Night Mode Default ENGLISH d D. Comp (Dynamic Range Compression) k Center Width Select the mode to match the source (cinema source, music source, etc.). Compress dynamic range (difference between loud and soft sounds). Assign center channel signal to front left and right channels for wider sound. n In the PLgx or PLg mode [Selectable items] Cinema :This is the mode for cinema source. Music :This is the mode for music source. Game :This is the mode for game source. Cinema : This is the mode for cinema source. Music : This is the mode for music source. You can operate “Cinema” mode or “Music” mode with the main remote control unit. Press [CINEMA] or [MUSIC]. Soften the treble range of movie soundtracks for better understanding. [Selectable items] ON :“Cinema EQ” is used. OFF :“Cinema EQ” is not used. ~ 3 ~ 7 l Delay Time :Middle setting. Adjust delay time to control sound stage size. High :High setting. [Variable range] When playing DTS sources, this is only displayed for compatible software. A0 Effect Level f LFE [Variable range] 0 ms ~ 30 ms ~ 110 ms Adjust the strength of the surround effect. 1 ~ 10 ~ 15 Adjust the low-frequency effects level (LFE). [Variable range] –10dB ~ 0dB Set to a lower level if the positioning and sense of phase of the surround signals seems unnatural. For proper playback of the different program sources, we recommend setting to the values below. • Dolby Digital sources: “0 dB” • DTS movie sources: “0 dB” • DTS music sources: “–10 dB” g Center Image Determine size of acoustic environment. [Selectable items] Small :Simulate acoustics of a small room. Med-S :Simulate acoustics of a medium-small room. Assign center channel signal to front left and right channels for wider sound. [Variable range] A1 Room Size ~ 0.0 ~ 0.3 1.0 h Panorama Med :Simulate acoustics of a medium room. Med-L :Simulate acoustics of a medium-large room. Large :Simulate acoustics of a large room. NOTE Assign front L/R signal also to surround channels, for wider sound. If the surround effect seems weak, set “Panorama” to “ON”. ON [Selectable items] “Room Size” does not indicate the size of the room in which sources are played. OFF j Dimension Shift sound image center to front or rear, to adjust playback balance. [Variable range] 0 ~ 3 ~ 6 For details on adjusting individual parameters, see “Adjusting the parameters” (vpage 33). 34 Troubleshooting s Cinema EQ Mid 0 Information The “Music” mode is also effective for movie sources including a lot of stereo music. Low :Low setting. [Variable range] Multi-Zone Operating from the main remote control unit :Turn dynamic range compression off. Playback Remote Control n In the DTS NEO:6 mode [Selectable items] OFF Setup PL :D olby Pro Logic playback mode (PLg mode only). (This is the mode for 4-channel playback (front L, front R, center, surround (MONO)).) [Selectable items] Getting Started Connections a Mode ENGLISH Getting Started Connections A2 SB CH OUT (for Multi-channel sources) A3 SUBWOOFER ATT. A8 MultEQ Select playback mode for surround back channels. Attenuate subwoofer level when using EXT. IN mode. Select the type of room correction desired from the following list: [Selectable items] [Selectable items] [Selectable items] OFF :No signal is played from the surround back channels. MTRX ON :The surround channel signals undergo digital matrix Setup Playback Remote Control PLIIx C z1 PLIIx M z2 ES MTRX z3 ES DSCRT z4 ON :The input from the subwoofer channel is attenuated. OFF :The input from the subwoofer channel is not attenuated. Usually use in this mode. processing and are output from the surround back channels. :Decoded in Dolby Pro Logic IIx Cinema mode, surround back signal played. Set this to “ON” if the subwoofer channel level seems too high when playing audio signal. :Decoded in Dolby Pro Logic IIx Music mode, surround back signal played. A4 Subwoofer :DTS signal played with digital matrix processing. Turn subwoofer output on and off. :Signal included in DTS-ES Discrete 6.1-channel sources played. [Selectable items] Multi-Zone Information z1: This can be selected when “Surround Back Speaker” is set to “2spkrs” at the “System Setup” – “Speaker Setup” setting (vpage 23). z2: This can be selected when “Surround Back Speaker” is set to “2spkrs” or “1spkr” at the “System Setup” – “Speaker Setup” setting. z3: This can be selected when playing DTS sources. z4: This can be selected when playing DTS sources including a discrete 6.1-channel signal identification signal. Troubleshooting Settings can also be made when [STD] is pressed. When using surround back speakers, adopt the following settings. q Adopt “7.1ch” for the Amp Assign setting. •The default setting for the Amp Assign mode of AVR-1709 is “ZONE2”. w Adopt a setting other than “OFF” for the “SB CH OUT” setting of “Surround Parameter”. A2 SB CH OUT (for 2-channel sources) Determine whether to use surround back speakers. [Selectable items] L and R speakers. Flat :Optimize frequency response of all speakers to flat response. OFF :Turn equalizer off. OFF OFF :The subwoofer is not used. • When “Audyssey”, “Audyssey Byp. L/R” or “Audyssey Flat” is selected, the Audyssey MultEQ indicator lights green. • After running Auto Setup, if the Speaker Configuration, Distance, Channel Level and Crossover Frequency have changed without increasing the number of speakers measured, the Audyssey MultEQ indicator lights red. Turn tone adjustments on and off. [Selectable items] ON :Allow tone adjustment (treble, bass). OFF :Playback without tone adjustment. The tone cannot be adjusted when in the DIRECT mode. NOTE When the “Dynamic EQ” setting is “ON”, setting is not possible. A6 Bass Adjust low frequency range (bass). ~ 0dB ~ +6dB ~ +6 dB A7 Treble :The surround back channel signal is played. Adjust high frequency range (treble). OFF :The surround back channel signal is not played. [Variable range] –6dB ~ Audyssey Flat Press MULTEQ. A5 Tone Control –6dB Audyssey Byp. L/R Operating from the main unit or main remote control unit :The subwoofer is used. ON 0dB “Bass” and “Treble” can be set when “Tone Control” is set to “ON”. 35 Byp. L/R :Optimize frequency response of speakers except front Audyssey ON [Variable range] Audyssey :Optimize frequency response of all speakers. For details on adjusting individual parameters, see “Adjusting the parameters” (vpage 33). NOTE • “MultEQ” can only be set when Auto Setup has been performed. • “MultEQ” cannot be set in the following situations. · If “Auto Setup” fails to be completed. ·After running Auto Setup, when the number of used speakers has increased from the number of measured speakers. • If the settings of speakers for which “None” has been determined at “Auto Setup” are changed, “Audyssey”, “Audyssey Byp. L/R” and “Audyssey Flat” cannot be selected. Either perform Auto Setup again, or return to the setting after running Auto Setup with “System Setup” – “Speaker Setup” – “Restore”. • When using headphones, “MultEQ” is set to “OFF”. ENGLISH S1 DV Setting (Dynamic Volume Setting) Audyssey Dynamic EQ solves the problem of deteriorating sound quality as volume is decreased by taking into account human perception and room acoustics. Audyssey Dynamic EQ works in tandem with Audyssey MultEQ to provide well-balanced sound for every listener at any volume level. Audyssey Dynamic Volume solves the problem of large variations in volume level between television programs, commercials, and between the soft and loud passages of movies. Audyssey Dynamic EQ is integrated into Dynamic Volume so that as the playback volume is adjusted automatically, the perceived bass response, tonal balance, surround impression, and dialog clarity remain the same. Set Dynamic Volume effect. NOTE [Selectable items] ON :Use Dynamic EQ function. OFF :Do not use Dynamic EQ function. ON :Use Dynamic Volume. The Dynamic Volume effect will be at the level of the “DV Setting”. OFF :Do not use Dynamic Volume. Press <DYN VOL> or [DYNAMIC VOLUME]. Dynamic EQ : ON / Volume : OFF Dynamic EQ / Volume : OFF Operating from the main unit or main remote control unit Press <DYN VOL> or [DYNAMIC VOLUME]. Dynamic EQ / Volume : ON Dynamic EQ : ON / Volume : OFF “Green” “Red” Dynamic EQ / Volume : OFF n Operating conditions for each function •Dynamic EQ : When “MultEQ” is set to “ON” •Dynamic Volume : When “Dynamic EQ” is set to “ON” •DV setting : When “Dynamic Volume” is set to “ON” A8 MultEQ A9 Dynamic EQ S0 Dynamic Volume S1 DV Setting “Off” Before running Auto Setup and after running Auto Setup, if the number of speakers has increased or you pressed <DYN VOL> or [DYNAMIC VOLUME], “Run Audyssey” is displayed. In this case, either perform Auto Setup again, or return to the setting after running Auto Setup with “System Setup” – “Speaker Setup” – “Restore”. Day NOTE •“DV Setting” can only be set when auto setup has been performed. •“DV Setting” cannot be set in the following situations. · If “Auto Setup” fails to be completed. ·After running Auto Setup, when the number of used speakers has increased from the number of measured speakers. · If “Dynamic Volume” setting is “OFF”. About Dynamic EQ Audyssey Dynamic EQ™ solves the problem of deteriorating sound quality as volume is decreased by taking into account human perception and room acoustics. Dynamic EQ selects the correct frequency response and surround levels moment-by-moment at any user-selected volume setting. The result is bass response, tonal balance, and surround impression that remain constant despite changes in volume. Dynamic EQ combines information from incoming source levels with actual output sound levels in the room, a prerequisite for delivering a loudness correction solution. Audyssey Dynamic EQ works in tandem with Audyssey MultEQ to provide well-balanced sound for every listener at any volume level. About Dynamic Volume Audyssey Dynamic Volume™ solves the problem of large variations in volume level between television programs, commercials, and between the soft and loud passages of movies. Dynamic Volume looks at the preferred volume setting by the user and then monitors how the volume of program material is being perceived by listeners in real time to decide whether an adjustment is needed. Whenever necessary, Dynamic Volume makes the necessary rapid or gradual adjustments to maintain the desired playback volume level while optimizing the dynamic range. Audyssey Dynamic EQ is integrated into Dynamic Volume so that as the playback volume is adjusted automatically, the perceived bass response, tonal balance, surround impression, and dialog clarity remain the same whether watching movies, flipping between television channels, or changing from stereo to surround sound content. For details on adjusting individual parameters, see “Adjusting the parameters” (vpage 33). 36 Troubleshooting Before running Auto Setup and after running Auto Setup, if the number of speakers has increased or you pressed <DYN VOL> or [DYNAMIC VOLUME], “Run Audyssey” is displayed. In this case, either perform Auto Setup again, or return to the setting after running Auto Setup with “System Setup” – “Speaker Setup” – “Restore”. Evening :Middle setting prevents loud and soft sounds from Information Dynamic EQ / Volume : ON to be of equal loudness. Multi-Zone Operating from the main unit or main remote control unit [Selectable items] :Low setting provides the least adjustments to the loudest and softest of sounds. Midnight :High setting affects volume the most, causing all sounds NOTE •“Dynamic Volume” can only be set when auto setup has been performed. •“Dynamic Volume” cannot be set in the following situations. · If “Auto Setup” fails to be completed. ·After running Auto Setup, when the number of used speakers has increased from the number of measured speakers. •When “MultEQ” is set to “OFF”, “Dynamic Volume” is automatically set to “OFF”. •“Night Mode” and “Tone Control” cannot be used jointly. being much louder and softer respectively than average sounds. [Selectable items] Playback Remote Control •“Dynamic EQ” can only be set when auto setup has been performed. •“Dynamic EQ” cannot be set in the following situations. · If “Auto Setup” fails to be completed. ·After running Auto Setup, when the number of used speakers has increased from the number of measured speakers. •When “MultEQ” is set to “OFF”, “Dynamic EQ” is automatically set to “OFF”. •“Night Mode” and “Tone Control” cannot be used jointly. Setup S0 Dynamic Volume Getting Started Connections A9 Dynamic EQ ENGLISH Getting Started Connections S2 RESTORER S3 Night Mode This function restores compressed audio signals to how they were before compression and corrects the sense of volume of the bass and treble to obtain richer playback sound. Optimized setting for late-night listening. Set the dynamic range compression of the output audio. [Selectable items] OFF [Selectable items] OFF : :Turn night mode off. Low :Low setting. Do not use RESTORER. Mid Mode1 (RESTORER 64): Setup Optimized mode for compressed sources with very weak highs. Playback Remote Control Apply suitable bass and treble boost for all compressed sources. :Middle setting. High :High setting. Mode2 (RESTORER 96): Operating from the main remote control unit Press [NIGHT]. OFF Mode3 (RESTORER HQ): Optimized mode for compressed sources with normal highs. The default setting for “iPod” is “Mode3”. All others are set to “OFF”. Operating from the main unit or main remote control unit Multi-Zone Press RESTORER. OFF Low Mid High NOTE When the “Dynamic EQ” setting is “ON”, setting is not possible. When the “Dynamic Volume” setting is “ON”, setting is not possible. S4 Default Mode 1 (RESTORER 64) Mode 2 (RESTORER 96) Information Mode 3 (RESTORER HQ) About the RESTORER function Resets the settings to the default values. [Selectable items] Yes :Reset. No :Do not reset. Troubleshooting • Such compressed audio formats as MP3, WMA (Windows Media Audio) and MPEG-4 AAC reduce the amount of data by eliminating signal components that are hard for the human ear to hear. The RESTORER function generates the signals eliminated upon compression, restoring the sound to conditions near those of the original sound before compression. It also corrects the sense of volume of the bass to obtain richer sound with compressed audio signals. • This is displayed on the “Surround Parameter” and can be set when the input source is selected to “SIRIUS” or analog signals (including FM/AM signals) or PCM signals (fs = 44.1/48 kHz) are input. 37 For details on adjusting individual parameters, see “Adjusting the parameters” (vpage 33). ENGLISH Getting Started Connections Information Symbols used to indicate buttons in this manual • Surround Mode • Input signal • Dialogue normalization • Input function • Input digital terminal • Audio Delay • Tone Control • Channel level of each speaker • CINEMA EQ • Night Mode etc. Playback Remote Control <STATUS> [Items to be checked] Setup Button located on both the main unit and the remote control unit BUTTON Button only on the main unit <BUTTON> Button only on the remote control unit [BUTTON] Information on the main unit’s various settings (Status) and on input signals (Audio Input Signal) is shown on the display. The information displayed changes each time you press <STATUS>. The information is displayed for several seconds before the display returns to its original condition. Multi-Zone Dialogue normalization function OFFSET Information This is automatically activated when playing Dolby Digital sources. This function automatically corrects the standard signal level for individual program sources. The correction value can be checked using <STATUS>. -4dB Troubleshooting The figure is the correction value when the standard level is corrected. • The items displayed will differ depending upon the current settings, the presence or absence of an input signal or the type of input signal, etc. • For details of the content of the items displayed, refer to the page containing an explanation of the settings. ENGLISH Getting Started Connections Playback Symbols used to indicate buttons in this manual Button located on both the main unit and the remote control unit BUTTON Button only on the main unit <BUTTON> Button only on the remote control unit [BUTTON] Setup Playback Remote Control SOURCE SELECT <STATUS> <MASTER VOLUME> PHONES jack <DIMMER> <SOURCE> <PHONES> Preparations Turning the Power On 1 2 Press <POWER>. Press <ON/STANDBY> or [ON/SOURCE]. The power indicator flashes green and the power turns on. Multi-Zone <POWER> <INPUT MODE> BAND <VIDEO SELECT> Turning the Power Off q Press <ON/STANDBY> or [OFF]. <SPEAKERS> TUNING <ON/STANDBY> Information Troubleshooting [ON/SOURCE] [OFF] [QUICK SELECT] SOURCE SELECT [TUNER] [MASTER VOLUME] TUNING [MUTING] [SOURCE CONTROL 1] [SOURCE CONTROL 2] [Rear] [TUNER] SOURCE SELECT [V.SEL] TUNING [MODE] BAND [INPUT] Set the input mode for this source. Press <INPUT MODE> or [INPUT]. Each time you press the button, the input mode display will change. Auto The power indicator lights red and the power is set to the standby mode. b Also press [SOURCE SELECT] when in standby mode, the power turns on. In this case the input source is selected by remote control unit. b Also press [QUICK SELECT] when in standby mode, the power turns on. In this case Quick Select is selected by remote control unit (vpage 46). [Front] Setting the Input Mode The power is set to the standby mode. w Press <POWER>. The power indicator turns off, and so does the power. NOTE Power continues to be supplied to some of the circuitry even when the power is in the standby mode. When leaving home for long periods of time or when traveling, either press <POWER> to turn off the power, or unplug the power cord from the power outlet. Selecting the Input Source Select the source using SOURCE SELECT. Turn <SOURCE SELECT> or press [SOURCE SELECT] to switch between input sources. If “Rec Select” is selected for the input source, press <SOURCE> before turning <SOURCE SELECT>. PCM EXT. IN DTS Analog [Selectable items] Auto : Detect type of digital input signal and decode and play automatically. PCM : Decode and play only PCM input signals. DTS : Decode and play only DTS input signals. Analog : Play only signals from analog input. EXT. IN : Play only signals from EXT. IN input. • When a digital signal is properly input, the “ ” indicator lights on the display. If the “ ” indicator does not light, check the digital input connector assignment and the connections. • The surround mode cannot be set if the input mode is set to “EXT. IN”. • Only set “PCM” and “DTS” when playing the respective signals. ENGLISH Adjusting the Master Volume Either turn <MASTER VOLUME> or press [MASTER VOLUME]. [Variable range] – – – –80.0dB ~ +18.0dB Checking the currently playing program source, etc. Press <STATUS>. The current program source and various settings are indicated on the display. For details, refer to “Information” (vpage 38). Switching the brightness of the display Press <DIMMER>. OFF Dim Dark Plug the headphones into the PHONES jack on the main unit. Basic Operation NOTE Be careful not to set the volume too high when using headphones. Press <SPEAKERS>. Front A Front B Front A+B 2 3 Use SOURCE SELECT to select the input source. q Load the DVD, CD or other software in the player. (vSee the operating instructions of the respective devices.) w To play a video device, switch the monitor input. (vSee the monitor’s operating instructions.) 3 4 Press BAND to select “FM” or “AM”. Tune in the desired broadcast station. q To tune in automatically (Auto Tuning) Press [MODE] to light the “AUTO” indicator on the display, then use TUNING to select the station you want to hear. w To tune in manually (Manual Tuning) Press [MODE] to turn off the display’s “AUTO” indicator, then use TUNING to select the station you want to hear. • If the desired station cannot be tuned in with auto tuning, tune it in manually. • When tuning in stations manually, press and hold TUNING to change frequencies continuously. Troubleshooting Switching the front speakers 1 Prepare the equipment. (vpage 47 “Remote Control Unit Operations”) Start playback. (vSee the operating instructions of the respective devices.) Video Select Function Switch video input source while listening to audio signal. Press <VIDEO SELECT> or [V.SEL] until the desired picture appears. Information The sound from the speakers and pre-out connectors is automatically cut. to “AUDIO” and [SOURCE to “TUNER”. Multi-Zone Listening with Headphones Playing Video and Audio Equipment or press [TUNER] to Remote Control When setting to “OFF”, the display brightness of the menu setting in operation changes to “Dark”. To cancel, press [MUTING] again. Muting can also be canceled by adjusting the master volume. Either turn select “TUNER”. Playback Turning Off the Sound Temporarily (Muting) Press [MUTING]. <SOURCE SELECT> 1 [SOURCE CONTROL 1] 2 CONTROL 2] Set Bright The adjustable range will differ depending upon factors such as the type of input signal and the channel level setting. Basic Operation Setup NOTE Listening to FM/AM Broadcasts Getting Started Connections Operations During Playback The remote control unit can be used to operate external devices. See “Remote Control Unit Operations” (vpage 47). b To cancel, press <VIDEO SELECT> to select “SOURCE”. 40 ENGLISH Getting Started Connections Symbols used to indicate buttons in this manual Button located on both the main unit and the remote control unit BUTTON Button only on the main unit <BUTTON> Button only on the remote control unit [BUTTON] <SOURCE SELECT> SHIFT ui Setup Playback Remote Control <STATUS> <PRESET CHANNEL> TUNING op [Front] [Rear] Presetting Radio Stations (Preset Memory) Your favorite broadcast stations can be preset so that you can tune them in easily. Up to 56 stations can be preset. 1 2 3 4 5 Tune in the broadcast station you want to preset. Press [MEMORY]. Press SHIFT to select the block (A to G) in which the station is to be preset. Press <PRESET CHANNEL> or [CHANNEL + –] to select the preset number (1 to 8). Press [MEMORY] again to complete the setting. Multi-Zone Information NOTE Troubleshooting SHIFT TUNING [CHANNEL + –] [ENTER] uiop [SOURCE CONTROL 1] [SOURCE CONTROL 2] [SAT TU] TUNING [ENTER] uiop [MEMORY] 1 2 Press SHIFT to select the memory block (A to G). Press <PRESET CHANNEL> or [CHANNEL + –] to select the desired preset channel (1 to 8). n Default settings Auto tuner presets • To preset other stations, repeat steps 1 to 5. • Stations can be preset automatically at “System Setup” – “Input Setup” – “Auto Preset Memory” (vpage 27). [SAT TU] Listening to Preset Stations Preset stations are erased by overwriting them. A1 ~ A8 87.5 / 89.1 / 98.1 / 107.9 / 90.1 / 90.1 / 90.1 / 90.1 MHz B1 ~ B8 520 / 600 / 1000 / 1400 / 1500 / 1710 kHz, 90.1 / 90.1 MHz C1 ~ C8 90.1 MHz D1 ~ D8 90.1 MHz E1 ~ E8 90.1 MHz F1 ~ F8 90.1 MHz G1 ~ G8 90.1 MHz ENGLISH What is SIRIUS Satellite Radio? Status Signal strength is excellent Signal strength is good Signal strength is weak No signal 2 Adjust the position of the antenna until “SIG.: EXCELLENT” is shown on the display. Press <STATUS> until the channel you want to check (example: “SR001”) is displayed. Press TUNING and select channel 0 (SR000). Channel No. and SIRIUS ID are alternately shown on the display. to “AUDIO” and [SOURCE to “TUNER”. SR000 SIRIUS ID (vpage 47 “Remote Control Unit Operations”) When selecting channel, the Channel No. and Channel name are displayed. • The channel switches continuously when TUNING is pressed and held. • SIRIUS Radio channels can be preset using the same procedure as for FM/AM stations (vpage 41 “Presetting Radio Stations (Preset Memory)” and “Listening to Preset Stations”). b You cannot perform “Auto Preset”. • The song title, artist name, composer name, category and reception level can be checked by pressing <STATUS>. • When tuning a channel to which “Parental Lock” is applied, “Code: [ ]” is displayed, so enter the password. SIRIUS ID b Write your own SIRIUS ID for storage use. SIRIUS ID : NOTE You can check Satellite and Terrestrial antenna signal strength each time you press <STATUS>. (On the display, “S” indicates Satellite, and “T” indicates Terrestrial.) Pops Channel category Use [o p] to select the category, then use [ui] to select the desired channel. • “UPDATING” is displayed while the encording code is being updated. • “SIRIUS UPDATING” is displayed when updating SIRIUS tuner firmware. • Refer to “Troubleshooting” (vpage 65) regarding other messages. Parental Lock 1 2 3 Tune to the channel you want to lock. 4 Press [ENTER]. Press [ENTER] for at least 3 seconds. “Code: [ ]” is displayed. Enter the 4-digit lock code using uiop. When you enter the correct code, the corresponding channel is locked. •Channels under Parental Lock cannot be tuned in by performing Tuning Up/Down or by category search. •Channels stored in preset memory can be tuned in by the preset channel select operation, even if Parental Lock is applied. •When a channel to which Parental Lock is applied is being played, Parental Lock for that channel is cancelled by performing Step 2. •See “Edit Lock Cord” (vpage 27) for the method of changing Parental Lock Cord. •You can also set “Parental Lock” from the system setup (vpage 27). 42 Troubleshooting 3 *************** Use TUNING to search the channel. CAT: Information Set The display will switch as shown below, depending on the reception conditions. Multi-Zone 1 [SOURCE CONTROL 1] 2 CONTROL 2] Either turn <SOURCE SELECT> or press [SAT TU] to select “SIRIUS”. CATEGORY SEARCH Remote Control Basic Operation Press [o p]. Press <STATUS> until “SIG.” appears on the display. Display EXCELLENT GOOD WEAK NO SIGNAL 3 4 5 1 Playback Sirius is available in the US for subscribers with addresses in the continental US and is available in Canada for subscribers with a Canadian address. Required subscription plus compatible SIRIUS tuner and antenna are required and sold separately. SIRIUS Programming is subject to change. Visit sirius.com for the most complete and up-todate channel lineup and product information. “SIRIUS” and the SIRIUS dog logo and related marks are trademarks of Sirius Satellite Radio Inc. All rights reserved. 1 2 Either turn <SOURCE SELECT> or press [SAT TU] to select “SIRIUS”. Searching Categories Setup Simply The Best Radio on RadioTM with all your favorite entertainment including 100% commercial-free music, plus superior sports coverage, uncensored talk and comedy, world-class entertainment, news, weather and more for your car, home or office. For more information visit sirius.com or siriuscanada.ca Checking the SIRIUS Signal Strength and Radio ID Getting Started Connections Listening to SIRIUS Satellite Radio Programs ENGLISH Getting Started Connections iPod® Playback Symbols used to indicate buttons in this manual Button located on both the main unit and the remote control unit BUTTON Button only on the main unit <BUTTON> Button only on the remote control unit [BUTTON] The music on an iPod can be played by using the control dock for iPod (ASD-1R, ASD-11R, ASD-3N or ASD-3W, sold separately). The operation can also be performed using the buttons on the remote control unit. iPod is a trademark of Apple Inc., registered in the U.S. and other countries. <SOURCE SELECT> Setup b The iPod may only be used to copy or play contents that are not copyrighted or contents for which copying or playback is legally permitted for your private use as an individual. Be sure to comply with applicable copyright legislation. Playback Remote Control Preparations 1 <ON/STANDBY> <STATUS> [Front] [Rear] Multi-Zone [OFF] Information [iPod] [2] [1] Troubleshooting [6], [7] [8], [9] [ENTER] [uip] [SOURCE CONTROL 1] [SOURCE CONTROL 2] Make the necessary preparations. q Set the iPod in the DENON control dock for iPod. (vSee the control dock for iPod’s operating instructions.) w Assign the control dock for iPod’s input. The input for the control dock for iPod is assigned to VCR by default. “System Setup” – “Input Setup” – “iPod Assign” (vpage 26) [iPod] [TUNING + –] [ENTER] [uip] [MODE] <SOURCE SELECT> 2 [SOURCE CONTROL 1] 3 CONTROL 2] Either turn or press [iPod] to select the input source assigned in step 1-w above. Set to “AUDIO” and [SOURCE to “iPod/NETWORK”. (v page 47 “Remote Control Unit Operations”) 4 Press [MODE] and hold it down for a 2 seconds or more to select the display mode. To switch between modes, press and hold down the button. When remote mode is active, “Remote” is displayed. [Selectable mode] Display location Browse mode Remote mode Main unit display iPod display Playable files Audio file Video file S S z1 S S z2 Active buttons Remote control unit (AVR-1709) S S iPod A S z1 : When using an ASD-3N or ASD-3W control dock for iPod. z2 : Video may not be output, depending on the combination of ASD-1R or ASD11R and iPod. • With the default settings, the iPod can be used connected to the VCR (iPod) connector. • Use the RESTORER mode to expand the low and high frequency components of compressed audio files and achieve a richer sound. The default setting is “Mode3” (vpage 37). • Press <ON/STANDBY> or [OFF] and set the AVR-1709’s power to the standby mode before disconnecting the iPod. Also switch the input source to one to which “iPod Assign” is not assigned before disconnecting the iPod. • When using an ASD-3N or ASD-3W control dock for iPod, refer to the respective manual to operate. ENGLISH 1 [p] [ui] 2 [ENTER] Use to select the item, then press [ENTER] or to select the music file to be played. Press Playback starts. or [p]. Viewing Still Pictures or Videos on the iPod Getting Started Connections Listening to Audio Photo and video data on the iPod can be viewed on the monitor. Only for iPod equipped with slideshow or video functions. When using an ASD-1R or ASD-11R Press again to resume playback. n Fast-forwarding or fast-reversing During playback, press and hold [6] (to fast-reverse) or [7] (to Press and hold [MODE] to set the Remote mode. Watching the iPod’s screen, use [ui] to select “Photos” or “Videos”. Playback Remote Control n Stopping playback temporarily During playback, press [ENTER] or [1]. 1 2 3 Setup You can perform the following operations also on the sub remote control unit (vpage 50). Press [ENTER] until the image you want to view is displayed. fast-forward). n To cue to the beginning of a track During playback, press [8] or [9]. n To stop During playback, either press and hold [ENTER] or press [2]. [Selectable items] All When using an ASD-3N or ASD-3W [MODE] 1 2 [p] [ENTER] [ui] 3 [ENTER] 4 [ui] [p] [ENTER] Press and hold One OFF to set the Browse mode. OFF Use • To check the name of the title, the artist or the album when playing in browse mode, press <STATUS>. • The folder name and the file name can be displayed in browse mode.Only alphanumeric characters and certain symbols can be displayed. Any characters that cannot be displayed are replaced with “ . (period)”. NOTE Use press to select “Video”, then press [p] or Troubleshooting . Information Watching the display, use [ui] to select “iPod”, then press or . n Shuffling playback Press [TUNING +]. [Selectable items] Albums Songs Multi-Zone n Playing repeatedly Press [TUNING –]. “TV Out” at the iPod’s “Slideshow Settings” or “Video Settings” must be set to “On” in order to display the iPod’s photo data or videos on the monitor. For details, see the iPod’s operating instructions. to select the video file to be played, then or . When viewing a still picture, perform the same operation as with ASD1R or ASD-11R. • Depending on the type of iPod and the software version, some functions may not operate. • DENON will accept no responsibility whatsoever for any loss of iPod data. 44 ENGLISH Getting Started Connections Other Operations and Functions Symbols used to indicate buttons in this manual Button located on both the main unit and the remote control unit BUTTON Button only on the main unit <BUTTON> Button only on the remote control unit [BUTTON] Setup Playback <SOURCE SELECT> <INPUT MODE> <SPEAKERS> ui Other Operations Recording on an External Device (REC OUT mode) You can listen to one program source while recording a different program source. 1 Press <ZONE2/REC SELECT> until “RECOUT” appears on the display. Remote Control ZONE2 2 Multi-Zone <POWER> QUICK SELECT <SELECT/ENTER>, op <ZONE2 / REC SELECT> Information [Front] [Rear] QUICK SELECT Troubleshooting 4 [CH SELECT/ ENTER] uiop [CH SELECT/ ENTER] uiop Turn <SOURCE SELECT> to choose the input source to be recorded. The “REC” indicator and the indicator for the selected source light. RECOUT SOURCE 3 RECOUT RECOUT TUNER ···· RECOUT SIRIUS Play the program source. For operating instructions, refer to the respective equipment’s operating instructions. To record FM or AM broadcasts, select the broadcast (vpage 40). Start recording. For operating instructions, refer to the respective equipment’s operating instructions. • To cancel, press <ZONE2/REC SELECT>, then turn <SOURCE SELECT> until “RECOUT SOURCE” is displayed. • Make a test recording before starting the actual recording. • Sources selected with the REC OUT mode are output from ZONE2 as well. • In the REC OUT mode, the remote control unit’s ZONE2 mode buttons cannot be operated. NOTE • Recordings you make are for your personal enjoyment and should not be used for other purposes without permission of the copyright holder. • Digital signals are not output from the REC OUT (CDR/TAPE and VCR) connector. • Audio and video signals input from the VCR IN connector are not output from the VCR OUT connector. Audio signal input from the CD-R/TAPE IN connector are not output from the CD-R/TAPE OUT connector. Convenient Functions Channel Level You can adjust the channel level either according to the playback sources or to suit your taste, as described below. 1 Press <SELECT/ENTER> or [CH SELECT/ENTER]. FL Vol.+ 1.5dB 2 Use ui, <SELECT/ENTER> or [CH SELECT/ENTER] to select the speaker. 3 Use o p to adjust the volume. The speaker that can be set switches each time one of the buttons is pressed. b In the case of a sub woofer, reducing the volume when it is at “–12 dB” will change the setting to OFF (none). ENGLISH Last Function Memory With this function, the currently playing input source, volume level, surround mode, MultEQ, Dynamic Volume, DV setting and front speaker can be stored in the memory. This stores the settings as they were directly before the standby mode was set. When the power is turned back on, the settings are restored to as they were directly before the standby mode was set. Set the input source, input mode, surround mode, MultEQ and volume to the conditions you want to store. 2 Press and hold QUICK SELECT until “Memory” appears on the display. Backup Memory The various settings are backed up for about 1 week, even if the power is turned off or the power cord is disconnected. Setup 1 Getting Started Connections Quick Select Function The current settings will be memorized. Volume –40 dB –40 dB –40 dB Perform this procedure if the display is abnormal or if operations cannot be performed. When the microprocessor is reset, all the settings are reset to their default values. 1 2 <INPUT<POWER> MODE> 3 Turn off the power using <POWER>. Press Once the display starts flashing at intervals of about 1 second, release the two buttons. Troubleshooting This function sets the settings (input mode, surround mode, MultEQ, Dynamic EQ, Dynamic Volume, audio delay etc.) last selected for the individual input sources. When you switch to an input source, the settings are automatically set to the ones that were set the last time that input source was used. while simultaneously pressing and <SPEAKERS>. Information Personal Memory Plus Function Multi-Zone To call out the settings, press QUICK SELECT at which the desired settings were stored. Resetting the Microprocessor Remote Control Quick Select 1 Quick Select 2 Quick Select 3 Input Source DVD/HDP TV/CBL VCR Playback [Quick Select Defaults] If in step 3 the display does not flash at intervals of about 1 second, start over from step 1. The surround parameters, tone control, MultEQ settings and the volumes of the different speakers are stored for the individual surround modes. 46 ENGLISH Getting Started Connections Remote Control Unit Operations Main Remote Control Unit (RC-1098) [Front] Setup Playback Remote Control [SOURCE CONTROL 1] [SOURCE CONTROL 2] Multi-Zone [Rear] Operating DENON Audio Components 1 2 Set [SOURCE CONTROL 1] to “AUDIO”. 3 Operate the audio component. Set [SOURCE CONTROL 2] to the position for the component to be operated (CD, iPod/NETWORK or TUNER). b For details, refer to the component’s operating instructions. b While this remote control unit is compatible with a wide range of infrared controlled components, it may be the case that some component models cannot be operated with this remote control unit. Information [MAIN ON] [NUMBER] • DENON and other makes of components can be operated by setting the preset memory. • Operation is not possible for some models. Troubleshooting 1 Set [SOURCE “VIDEO”. CONTROL 1] to “AUDIO” or b Set to the AUDIO side for the CD position, and to the VIDEO side for the DVD/HDP, VCR, SAT/CABLE or TV position. Depending on the model and year of manufacture of your equipment, some buttons may not operate. 2 3 4 5 47 Operating Preset Components 1 Presetting [ZONE2 OFF] • The signals for the pressed buttons are emitted while setting the preset memory. To avoid accidental operation, cover the remote control unit’s transmitting window while setting the preset memory. • Depending on the model and year of manufacture, this function cannot be used for some models, even if they are of makes listed in the list of preset codes. • Some manufacturers use more than one type of remote control code. Refer to the included list of preset codes to change the number and verify correct operation. • The preset memory can be set for one component only among the following: DVD/HDP and SAT/CABLE. • VDP (Video Disc Player) can be preset when [SOURCE CONTROL 2] is set to “DVD/HDP”. Set [SOURCE CONTROL 2] to the component to be registered. Press [ZONE2 OFF] and [MAIN ON] at the same time. The indicator starts flashing. Press [NUMBER] and input the 3-digit number of the brand of the component to be preset. The numbers are shown in the Preset Code Table (vEnd of this manual). To store the codes of another component in the memory, repeat steps 1 to 4. Set [SOURCE “VIDEO”. CONTROL 1] to “AUDIO” or b Set to the AUDIO side for the CD position, and to the VIDEO side for the DVD/HDP, VCR, SAT/CABLE or TV position. 2 3 Set [SOURCE CONTROL 2] to the component you want to operate. Operate the component. b For details, refer to the component’s operating instructions. b Some models cannot be operated with this remote control unit. ENGLISH n Front [OFF] [ON/SOURCE] Device operated SOURCE CONTROL 1 SOURCE CONTROL 2 OFF [SOURCE CONTROL 2] Tuner DVD Player Blu-ray Disc Player Video Disc Player AUDIO Video Deck Satellite Receiver Cable TV TV (Monitor) VIDEO CD iPod/ NETWORK TUNER – – – DVD / HDP Power off VCR SAT / CABLE TV Power off – – – – – Power on / Standby Power on / Standby Power on / Standby Power on / Standby Punch through Punch through Punch through – – – Power on Power on 1 Play Play / Pause – Play Play Play Play 2 Stop Stop – Stop Stop Stop Stop SHIFT, 3 Pause – Shift Pause Pause Paus e Pause 0, SKIP + / FAVORITE Disc skip + b Favorites Direct – Disc skip – – – TUNING, 6 7 Manual search (fast-reverse / fastforward) Manual search (fast-reverse / fastforward) Tuning down / up Manual search (fast-reverse / fastforward) Manual search (fast-reverse / fastforward) Manual search (fast-reverse / fastforward) 8 9, CH + – Auto search (cue) Auto search (cue) Tuner Channel – / + Auto search (cue) Auto search (cue) Auto search (cue) Manual search (fast-reverse / fastforward) Switch channels (–, +) SETUP – – – Setup Setup – – – – – uio p – Cursor – – Cursor operation Cursor operation Cursor operation – – – Cursor operation Switching the audio signal – AUDIO Cursor operation Switching the audio signal – – – – – ENTER – Enter – Enter setting Enter setting – – Enter setting Enter setting Enter setting DISPLAY – – – Switching the display Switching the display – – Switching the display Switching the display Switching the display RETURN – – – Return Return – – Return Return Return – Calling out the menus Calling out the menus – Calling out the menus Calling out the menus Calling out the menus – – bThe iPod/NETWORK’s FAVORITE button can be operated when using a control dock for iPod ASD-3N or ASD-3W. 48 Troubleshooting – Information MENU / GUIDE Multi-Zone ON/SOURCE Power on / Standby Playback Remote Control [SOURCE CONTROL 1] [SETUP], [uiop], [AUDIO], [ENTER], [DISPLAY], [RETURN], [MENU/GUIDE] iPod Setup [1], [2], [SHIFT, 3], [0, SKIP + / FAVORITE], [TUNING, 6 7], [8 9, CH + –] CD Player Getting Started Connections Functions of Buttons by Component ENGLISH Getting Started Connections n Rear Device operated SOURCE CONTROL 1 SOURCE CONTROL 2 [NUMBER] (0~9, +10) Setup Playback [TUNING + – / TV VOL + –], [MODE, TOP MENU], [BAND, PICTURE ADJUST], [MEMORY, SUBTITLE] [SETUP], [uiop], [AUDIO], [ENTER], [DISPLAY], [RETURN] CD Player iPod Tuner DVD Player Blu-ray Disc Player Video Disc Video Deck Player AUDIO Satellite Receiver Cable TV TV (Monitor) VIDEO Remote Control Multi-Zone Information Troubleshooting CD iPod/ NETWORK NUMBER (0 ~ 9, +10) – – TUNING (+, –) / TV VOL (+, –) q CD Random w CD Repeat MODE, TOP MENU – SETUP – q iPod Random w iPod Repeat Page search mode (once) and Browse/ Remote mode switching (Press and hold) – uio p – – – AUDIO BAND, PICTURE ADJUST ENTER MEMORY, SUBTITLE – – – – DISPLAY RETURN Default setting (Preset code) Special Remarks TUNER DVD / HDP Number input / Track selection q DVD q Tuning up Random w Tuning w DVD down Repeat – Switch search modes VCR Number Number input / input / Track Track selection selection q Blu-ray Disc q TV Random Volume d w Blu-ray Disc w TV Repeat Volume f SAT / CABLE TV – Channels Channels Channels q TV Volume d w TV Volume f q DBS Volume d w DBS Volume f q Cable Volume d w Cable Volume f q TV Volume d w TV Volume f – – Calling out the menus Calling out the menus Calling out the menus – Cursor operation – – Cursor operation – Calling out the menus Calling out the top menus Setup Cursor operation Audio – – – – – Setup Cursor operation Audio – – – Cursor operation – b1 Top menu FM / AM switching Picture adjust Picture adjust – – – – – – b1 Favorite memory – Preset memory Enter setting Enter setting – – Enter setting Enter setting Enter setting Subtitle Subtitle – – – – – – – – – – – Switching the display Return – – Switching the display Return – – Switching the display Return Switching the display Return Switching the display Return DENON (111) – – DENON (111) b2 DENON (121) – HITACHI (108) – ABC (007) HITACHI (134) q – – – – q, w q q, e q, e GSpecial RemarksH q Only one device can be set in the preset memory for each mode. When a new preset code is registered, the existing code is automatically erased. w For some brands, the DVD remote control buttons may have different function names. Check beforehand. e One of the following buttons can be assigned to the TV and satellite receiver or cable TV: CD, iPod/NETWORK, TUNER, DVD/HDP, VCR (v“Punch Through Function”). b1:This button can be operated when using a control dock for iPod ASD-3N or ASD-3W. b2:The initial setting of Preset code is 111 (DVD Player). With the Blu-ray Disc Player setting, when you have set the remote controller code to “DENON2”, use the Blu-ray Disc Player preset code “121”. 49 ENGLISH “Punch Through” is a function allowing you to operate 1, 2, 3, 0, 6, 7, 8 and 9 on CD, iPod/NETWORK, TUNER, DVD/ HDP or VCR components when in the SAT/CABLE or TV mode. By default, nothing is set. Press [MEMORY] and [RETURN] at the same time. The indicator starts flashing. Input the number of the component you want to set. No. 1 iPod/NETWORK 2 TUNER 3 DVD/HDP 4 VCR 5 No setting 0 [SOURCE SELECT] [CHANNEL +, –] [TUNING +, –] [8], [9] [1/3], [2] [REPEAT] [Rear] [RETURN] Power off Power on Switching the input source Volume control Channel + / – Tuning + / – Muting Switching the memory block Auto search (cue) Stop Play / Pause 1-track / All -track repeat play 1-track / album shuffle play Troubleshooting [MEMORY] [VOLUME +, –] [MUTE] [SHIFT] [FAVORITES DIRECT PLAY] [RANDOM] Information [NUMBER] POWER OFF POWER ON SOURCE SELECT VOLUME +, – CHANNEL +, – TUNING +, – MUTE SHIFT 8 9 2 1/3 REPEAT RANDOM [POWER ON] Multi-Zone CD [POWER OFF] Remote Control [SOURCE CONTROL 2] Set [SOURCE CONTROL 2] to the component to be registered (SAT/CABLE or TV). bThe following describes operation for the selected zone. • Turning the multi-zone power on and off • Selecting the input source to be played • Adjusting and temporarily muting the multi-zone volume • Listening to the tuner •Operating an iPod (Note that [FAVORITES DIRECT PLAY] can only be used with the ASD-3N or ASD-3W.) Playback [SOURCE CONTROL 1] 1 2 3 4 The sub remote control unit (RC-1108) included with the AVR-1709 can be used as the exclusive multi-zone remote control unit. Setup [1], [2], [3], [0], [6 7], [8 9] Set [SOURCE CONTROL 1] to “VIDEO”. Sub Remote Control Unit (RC-1108) Getting Started Connections Punch Through Function [Front] bWhen using a control dock for iPod (ASD-1R or ASD-11R), the [FAVORITES DIRECT PLAY] cannot be used. 50 ENGLISH Getting Started Connections Amp Assign / Multi-zone Connections and Operations The AVR-1709 is compatible with the following types of playback: • Multi-zone playback (ZONE2) • Bi-amp playback (front speakers) Setting 1 : F Multi-zone playback 5.1-channel playback + ZONE2 stereo playback NOTE Setup • For bi-amp playback, use speakers compatible with that type of connection. • When conducting bi-amp playback, remove the short-circuiting boards (or wires) from the speaker terminals. Playback Remote Control Multi-zone Settings with the Amp Assign Function The amp assign function lets you assign the amplifiers for the different channels built into the AVR-1709 to the speaker outputs for the different zones. Select the desired playback environment from among “Setting 1” to “Setting 3”, then set the corresponding “Amp Assign” mode at “System Setup” – “Option Setup” – “Amp Assign” (vpage 28). Connect the speakers as described at “Speaker connections and channels outputting to the various speaker terminals”. Main zone FL SW SL C 5.1ch ZONE2 FR SR + Z2L ZONE2 (Default) Stereo n Speaker connections and channels outputting to the various speaker terminals Multi-Zone Speaker terminal Information Amp Assign mode ZONE2 Troubleshooting 51 Amp Assign mode: Z2R FRONT CENTER R L FR FL C SURROUND SURROUND BACK/ AMP ASSIGN R L R L SR SL Z2R Z2L ENGLISH F 7.1-channel Setting 3 : playback F Making bi-amp connections for the FL and FR channels in the main zone and conducting 5.1-channel playback Main zone FL SW C Getting Started Connections Setting 2 : (switching with other modes not possible) FR Main zone FL SW Amp Assign mode: 7.1ch SL SR FR 7.1ch Amp Assign mode: 5.1ch FL/FR Bi-Amp SR Front A Bi-Amp Setup SL SBL C Front B Bi-Amp SBR Speaker terminal Amp Assign mode 7.1ch FRONT CENTER R L FR FL C SURROUND SURROUND BACK/ AMP ASSIGN R L R L SR SL SBR SBL n Speaker connections and channels outputting to the various speaker terminals Speaker terminal FRONT-B R R L CENTER L SURROUND R L Front A Bi-Amp FR-A FR-B FL-B C SR SL R L FR FL FL-A/FR-A Bi-Amp connection FR FL FL-B/FR-B Bi-Amp connection Information Front B Bi-Amp FL-A SURROUND BACK / AMP ASSIGN Multi-Zone Amp Assign mode FRONT-A Playback Remote Control n Speaker connections and channels outputting to the various speaker terminals Troubleshooting 52 ENGLISH Getting Started Connections Multi-zone Settings and Operations with Zone Output Prepare pre-main amplifiers for ZONE2. Connectors for audio output Audio signals ZONE2 OUT Stereo ZONE2 Setup Main zone (7.1-channel system) ZONE2 Monitor Pre-main amplifier y Playback Remote Control '- 48 '3 $ AVR-1709 DVD player ZONE2 audio output Input 43 4- Multi-Zone Remote control unit 4# - 4# 3 : Multi-zone audio cable Information Troubleshooting 53 ENGLISH Button located on both the main unit and the remote control unit BUTTON Button only on the main unit <BUTTON> Button only on the remote control unit [BUTTON] <SOURCE SELECT> Turning the Power On and Off GOperation on the main unitH Press <ZONE2 ON/OFF> for the zone to be operated. Turning off the Sound Temporarily Set [SOURCE CONTROL 1] to “AUDIO” and [SOURCE CONTROL 2] to “ZONE2” (main remote control unit). Press [MUTING]. b To cancel, either adjust the volume or press [MUTING] again. The setting is canceled when the zone’s power is turned off. GOperation on the remote control unitH Press [ZONE2 ON] or [ZONE2 OFF]. NOTE Digital audio signals input from the COAXIAL or OPTICAL connectors cannot be played in multi-zone. Selecting the Input Source <ZONE2 ON/OFF> <ZONE2 / REC SELECT> GOperation on the main unitH Press <ZONE2 / REC SELECT>, then turn <SOURCE SELECT>. [Rear] [SOURCE SELECT] [VOLUME] With ZONE2, only the buttons indicated in this illustration can be operated. [SOURCE CONTROL 2] Adjusting the Volume Set [SOURCE CONTROL 1] to “AUDIO” and [SOURCE CONTROL 2] to “ZONE2” (main remote control unit). Press [VOLUME]. [Variable range] ––– Troubleshooting [MUTING] “ZONE2” (main remote control unit). Press [SOURCE SELECT]. Information [ZONE2 OFF] [ZONE2 ON] [MAIN OFF] [MAIN ON] [SOURCE SELECT] GOperation on the remote control unitH Set [SOURCE CONTROL 1] to “AUDIO” and [SOURCE CONTROL 2] to Multi-Zone [Front] –70dB ~ –40dB ~ +18dB NOTE [SOURCE CONTROL 1] Buttons other than these cannot be operated. The ZONE2 volume can be adjusted only when “ZONE2” is selected at “System Setup” – “Option Setup” – “Amp Assign” (vpage 28). (Main remote control unit) [ZONE2 OFF] [SOURCE SELECT] Playback Remote Control When using ZONE2, it is possible to turn the power for the MAIN ZONE only on or off by pressing [MAIN ON] or [MAIN OFF]. Setup The source selected for ZONE2 is also output from the recording output connectors. Getting Started Connections Multi-zone Operations Symbols used to indicate buttons in this manual [ZONE2 ON] [VOLUME] [MUTING] (Sub remote control unit) ENGLISH Getting Started Connections Other Information About Speaker Installation Surround back speakers Setup Playback Remote Control Sound positioning directly to the rear can be achieved easily by adding a surround back speaker to a 5.1-channel system. In addition, the acoustic image extending between the sides and the rear is narrowed, thus greatly improving the expression of the surround signals for sounds moving from the sides to the back and from the front to the point directly behind the listening position. Change of positioning and acoustic image with 5.1-channel systems '- 48 $ '3 Number of surround back speakers Placement of the surround left and right channels when using surround back speakers w Setting for primarily watching movies using diffusion type speakers for the surround speakers For the greatest sense of surround sound envelopment, diffuse radiation speakers such as bipolar types, or dipolar types, provide a wider dispersion than is possible to obtain from a direct radiating speaker (monopolar). Place these speakers at either side of the prime listening position, mounted above ear level. We recommend installing the speakers for the surround “L” and “R” channels a bit forward. Path of the surround sound from the speakers to the listening position We recommend using 2 speakers. When using dipolar speakers in particular, be sure to use 2 speakers. Examples of speaker layouts Below we introduce examples of speaker layouts. Refer to these to arrange your speakers according to their type and how you want to use them. Surround speaker Surround speakers Front speaker G1H Using surround back speaker(s) 2 to 3 feet Multi-Zone q When mainly playing movies Recommended when your surround speakers are single or 2-way speakers. Information Front speakers Center speaker 4-DI Troubleshooting Change of positioning and acoustic image with 6.1-channel systems 48 60° Surround back speakers GAs seen from aboveH GAs seen from the sideH $ 4-DI Front speakers Center speaker 60° Surround speaker '3 43DI e When playing movies and music Monitor Subwoofer Surround speakers Surround back speaker Front speaker 2 to 3 feet Point slightly downwards 60° Monitor Subwoofer 45° ~ 60° Surround speakers GAs seen from aboveH 4#DI Movement of acoustic image from SR to SB to SL In addition to sources recorded in 6.1-channels, the surround effect of conventional 2- to 5.1-channel sources can also be enhanced. Surround speaker Surround back speaker Front speaker 2 to 3 feet Surround back speakers 55 Point slightly downwards 43DI Movement of acoustic image from SR to SL '- Surround back speaker GAs seen from the sideH Surround back speakers GAs seen from aboveH GAs seen from the sideH Point slightly downwards ENGLISH Front speakers Center speaker Monitor Subwoofer 60° Surround speaker Front speaker Surround speakers GAs seen from aboveH GAs seen from the sideH Surround Dolby Digital Dolby Digital EX is a 6.1-channel surround format proposed by Dolby Laboratories that allows users to enjoy in their homes the “DOLBY DIGITAL SURROUND EX” audio format jointly developed by Dolby Laboratories and Lucas Films. The 6.1 channels of sound, including surround back channels, provide improved sound positioning and expression of space. Manufactured under license from Dolby Laboratories. “Dolby”, “Pro Logic” and the double-D symbol are trademarks of Dolby Laboratories. DTS-ES™ Discrete 6.1 DTS-ES™ Discrete 6.1 is a 6.1-channel discrete digital audio format adding a surround back (SB) channel to the DTS digital surround sound. Decoding of conventional 5.1-channel audio signals is also possible according to the decoder. DTS-ES™ Matrix 6.1 DTS-ES™ Matrix 6.1 is a 6.1-channel discrete digital audio format inserting a surround back (SB) channel to the DTS digital surround sound through matrix encoding. Decoding of conventional 5.1-channel audio signals is also possible according to the decoder. DTS NEO:6™ Surround DTS NEO:6™ is a matrix decoding technology for achieving 6.1channel surround playback with 2-channel sources. It includes “DTS NEO:6 CINEMA” suited for playing movies and “DTS NEO:6 Music” suited for playing music. DTS 96/24 DTS 96/24 is a digital audio format enabling high sound quality playback in 5.1-channels with a sampling frequency of 96 kHz and 24 bit quantization on DVD-Video. Manufactured under license under U.S. Patent #’s: 5,451,942; 5,956,674; 5,974,380; 5,978,762; 6,226,616; 6,487,535; 7,003,467; 7,212,872 & other U.S. and worldwide patents issued & pending. DTS, DTS Digital Surround, ES, and Neo:6 are registered trademarks and the DTS logos, Symbol and DTS 96/24 are trademarks of DTS, Inc. © 1996-2007 DTS, Inc. All Rights Reserved. 56 Troubleshooting Dolby Digital is a multichannel digital signal format developed by Dolby Laboratories. A total of 5.1-channels are played: 3 front channels (“FL” , “FR” and “C”), 2 surround channels (“SL” and “SR”) and the “LFE” channel for low frequencies. Because of this, there is no crosstalk between channels and a realistic sound field with a “three-dimensional” feeling (sense of distance, movement and positioning) is achieved. A real, overpowering sense of presence is achieved when playing movie sources in AV rooms as well. Dolby Digital EX DTS Digital Surround is the standard digital surround format of DTS, Inc., compatible with a sampling frequency of 44.1 or 48 kHz and up to 5.1-channels of digital discrete surround sound. Information Dolby Surround Dolby Pro Logic gx is a further improved version of the Dolby Pro Logic g matrix decoding technology. Audio signals recorded in 2-channels are decoded to achieve a natural sound with up to 7.1-channels. There are 3 modes: “Music” suited for playing music, “Cinema” suited for playing movies, and “Game” which is optimized for playing games. DTS Digital Surround Multi-Zone The AVR-1709 is equipped with a digital signal processing circuit that lets you play program sources in the surround mode to achieve the same sense of presence as in a movie theater. Dolby Pro Logic gx DTS Surround Playback Remote Control 120° Dolby Pro Logic g is a matrix decoding technology developed by Dolby Laboratories. Regular music such as that on CDs is encoded into 5-channels to achieve an excellent surround effect. The surround channel signals are converted into stereo and full band signals (with a frequency response of 20 Hz to 20 kHz or greater) to create a “three-dimensional” sound image offering a rich sense of presence for all stereo sources. Setup 2 to 3 feet Dolby Pro Logic g Getting Started Connections G2H When not using surround back speakers ENGLISH Getting Started Connections Audyssey Audyssey MultEQ® Audyssey MultEQ is a room equalization solution that calibrates any audio system so that it can achieve optimum performance for every listener in a large listening area. Based on several room measurements, MultEQ calculates an equalization solution that corrects for both time and frequency response problems in the listening area and also performs a fully automated surround system setup. Setup Audyssey Dynamic EQ™ Playback Remote Control Audyssey Dynamic EQ solves the problem of deteriorating sound quality as volume is decreased by taking into account human perception and room acoustics. Audyssey Dynamic EQ works in tandem with Audyssey MultEQ to provide well-balanced sound for every listener at any volume level. Audyssey Dynamic Volume™ Multi-Zone Audyssey Dynamic Volume solves the problem of large variations in volume level between television programs, commercials, and between the soft and loud passages of movies. Audyssey Dynamic EQ is integrated into Dynamic Volume so that as the playback volume is adjusted automatically, the perceived bass response, tonal balance, surround impression, and dialog clarity remain the same. Information Troubleshooting Manufactured under license from Audyssey Laboratories. U.S. and foreign patents pending. Audyssey MultEQ® is a registered trademark of Audyssey Laboratories. Audyssey Dynamic EQ™ is a trademark of Audyssey Laboratories. Audyssey Dynamic Volume™ is a trademark of Audyssey Laboratories. 57 HDMI (High-Definition Multimedia Interface) HDMI is a digital interface standard for next generation TVs based on DVI (Digital Visual Interface) standards and optimized for use in consumer equipment. Non-compressed digital video and multi-channel audio signals are transmitted with a single connection. HDMI is also compatible with HDCP (High-bandwidth Digital Contents Protection), a technology for protecting copyrights that encrypts digital video signals in the same was as with DVI. Deep Color Eliminates on-screen color banding, for smooth tonal transitions and subtle gradations between colors. Enables increased contrast ratio. Can represent many times more shades of gray between black and white. At 30-bit pixel depth, a four times improvement would be the minimum, and the typical improvement would be eight times or more. xvYCC Next-generation “xvYCC” color space supports 1.8 times as many colors as existing HDTV signals. Lets HDTVs display colors more accurately. Enables displays with natural, vivid colors. “HDMI”, “HDMI logo” and “High-Definition Multimedia Interface” are trademarks or registered trademarks of HDMI Licensing LLC. ENGLISH Signals and adjustability in the different modes Channel output Surround mode Parameter (default values are shown in parentheses) Front L/R Center Surround L/R Surround Back L/R Subwoofer D. Comp DIRECT S A A A D S (OFF) STEREO S A A A D S (OFF) EXT. IN S D D D D A LFE Cinema EQ. Mode Room Size Effect Level Delay Time Subwoofer S (0 dB) A A A A A A S S (0 dB) A A A A A A A A A A A A A A A S A A A A z1 z1 DOLBY PRO LOGIC gx S D D D D S (OFF) A S (NOTE3) S (OFF, NOTE1) DOLBY PRO LOGIC g S D D A D S (OFF) A A S (OFF, NOTE2) S A A A A D D D D S (OFF) A S (NOTE3) S A A A A S D D D D S (OFF) S (0 dB) S (NOTE3) S (OFF) A A A A A DTS SURROUND S D D D D A S (0 dB) S (NOTE3) S (OFF) A A A A A 5CH / 7CH STEREO S D D D D S (OFF) S (0 dB) S (NOTE3) A A A A A A ROCK ARENA S D D D D S (OFF) S (0 dB) S (NOTE3) A A S (Medium) S (10) A A JAZZ CLUB S D D D D S (OFF) S (0 dB) S (NOTE3) A A S (Medium) S (10) A A MONO MOVIE S D D D D S (OFF) S (0 dB) S (NOTE3) A A S (Medium) S (10) A A VIDEO GAME S D D D D S (OFF) S (0 dB) S (NOTE3) A A S (Medium) S (10) A A MATRIX S D D D D S (OFF) S (0 dB) S (NOTE3) A A A A S (30 ms) A VIRTURL S A A A D S (OFF) S (0 dB) A (NOTE3) A A A A A A 58 Troubleshooting S : Enable A : Unable NOTE1 :This parameter is available when “Surround Parameter” – “Mode” is set to “Cinema” (vpage 34). NOTE2 :This parameter is available when “Surround Parameter” – “Mode” is set to “Cinema” or “PL” (vpage 34). NOTE3 :“System Setup” – “Speaker Setup” – “Speaker Configuration” – “Surround Back Speaker” are only displayed when “Small” or “Large”. NOTE: z1 :When playing Dolby Digital and DTS signals. Information S : Signal / Adjustable A : No signal / Not adjustable D : Turned on or off by speaker configuration setting Multi-Zone S DOLBY DIGITAL Playback Remote Control DTS NEO:6 S (OFF, NOTE1) Setup SB CH OUT Getting Started Connections Surround Modes and Parameters ENGLISH Getting Started Connections Signals and adjustability in the different modes Parameter (default values are shown in parentheses) Surround mode PRO LOGIC g/gx MUSIC mode only NEO:6 MUSIC mode only EXT. IN only Tone Control (NOTE5) Night Mode (NOTE5) MultEQ Dynamic EQ (NOTE6) Dynamic Volume (NOTE7) DV Setting RESTORER Panorama Dimension Center Width Center Image SUBWOOFER ATT. DIRECT A A A A A A S (OFF) S (OFF, NOTE4) S (ON, NOTE4) S (OFF, NOTE4) S (Midnight, NOTE8) A STEREO A A A A A S (0 dB) S (OFF) S (OFF, NOTE9) S (ON, NOTE9) S (OFF, NOTE9) S (Midnight, NOTE8) S (OFF, NOTE10) EXT. IN Setup A A A A S A A A A A A A DOLBY PRO LOGIC gx S (OFF) S (3) S (3) A A S (0 dB) S (OFF) S (OFF, NOTE9) S (ON, NOTE9) S (OFF, NOTE9) S (Midnight, NOTE8) S (OFF, NOTE10) DOLBY PRO LOGIC g Playback Remote Control S (OFF) S (3) S (3) A A S (0 dB) S (OFF) S (OFF, NOTE9) S (ON, NOTE9) S (OFF, NOTE9) S (Midnight, NOTE8) S (OFF, NOTE10) DTS NEO:6 A A A S (0.3) A S (0 dB) S (OFF) S (OFF, NOTE9) S (ON, NOTE9) S (OFF, NOTE9) S (Midnight, NOTE8) S (OFF, NOTE10) DOLBY DIGITAL A A A A A S (0 dB) S (OFF) S (OFF, NOTE9) S (ON, NOTE9) S (OFF, NOTE9) S (Midnight, NOTE8) A DTS SURROUND A A A A A S (0 dB) S (OFF) S (OFF, NOTE9) S (ON, NOTE9) S (OFF, NOTE9) S (Midnight, NOTE8) A 5CH / 7CH STEREO A A A A A S (0 dB) S (OFF) S (OFF, NOTE9) S (ON, NOTE9) S (OFF, NOTE9) S (Midnight, NOTE8) S (OFF, NOTE10) ROCK ARENA A A A A A S (NOTE3) S (OFF) S (OFF, NOTE9) S (ON, NOTE9) S (OFF, NOTE9) S (Midnight, NOTE8) S (OFF, NOTE10) JAZZ CLUB A A A A A S (0 dB) S (OFF) S (OFF, NOTE9) S (ON, NOTE9) S (OFF, NOTE9) S (Midnight, NOTE8) S (OFF, NOTE10) MONO MOVIE A A A A A S (0 dB) S (OFF) S (OFF, NOTE9) S (ON, NOTE9) S (OFF, NOTE9) S (Midnight, NOTE8) S (OFF, NOTE10) VIDEO GAME A A A A A S (0 dB) S (OFF) S (OFF, NOTE9) S (ON, NOTE9) S (OFF, NOTE9) S (Midnight, NOTE8) S (OFF, NOTE10) MATRIX A A A A A S (0 dB) S (OFF) S (OFF, NOTE9) S (ON, NOTE9) S (OFF, NOTE9) S (Midnight, NOTE8) S (OFF, NOTE10) VIRTURL A A A A A S (0 dB) S (OFF) S (OFF, NOTE9) S (ON, NOTE9) S (OFF, NOTE9) S (Midnight, NOTE8) S (OFF, NOTE10) Multi-Zone S : Adjustable A : Not adjustable NOTE3 : BASS +6 dB, TREBLE +4 dB NOTE4 : When “System Setup” – “Option Setup” – “Direct Mode Setup” are turned “ON”, also after implementing “Auto Setup”. NOTE5 : This parameter is not availabe when “Surround Parameter” – “Dynamic EQ” is set to “ON” (vpage 36). NOTE6 : This parameter is not availabe when “Surround Parameter” – “MultEQ” is set to “OFF” (vpage 35). NOTE7 : This parameter is not availabe when “Surround Parameter” – “Dynamic EQ” is set to “OFF” (vpage 36). NOTE8 : Displayed when “Dynamic Volume” setting is “ON”. NOTE9 : Displays after implementing Auto Setup. NOTE10 : Displayed when input signal is “Analog” or “PCM 44.1/48 kHz”. Information Troubleshooting 59 ENGLISH Input signals Button DTS Surround mode Note ANALOG LINEAR PCM LINEAR PCM (Multi ch) DTS ES DSCRT (With Flag) DOLBY DIGITAL DTS ES MTRX (With Flag) DTS (5.1ch) DTS 96/24 DOLBY DOLBY DIGITAL EX DIGITAL EX (With Flag) (With no Flag) DOLBY DIGITAL (5.1/5/4ch) DOLBY DIGITAL (4/3ch) DOLBY DIGITAL (2ch) STANDARD DTS SURROUND z1 A A A F A A A A A A A A DTS ES MTRX6.1 z1 A A A A F A A A A A A A DTS SURROUND A A A D D FD A A A A A A DTS 96/24 A A A A A A FD A A A A A z2 A A A A A S S A A A A A DTS + PLgx MUSIC z1 A A A A A S S A A A A A DTS + NEO:6 z1 A A A A A S S A A A A A DTS NEO:6 CINEMA S S A A A A A A A A A S DTS NEO:6 MUSIC S S A A A A A A A A A S A A A A A A A F b1 A A A A A A A D Playback Remote Control DTS + PLgx CINEMA Setup DTS ES DSCRT6.1 DOLBY Surround DOLBY DIGITAL EX z1 DOLBY DIGITAL S S S A DF DF DF A A A A A A A A A F b2 S S S DOLBY DIGITAL + PLgx MUSIC z1 A A A A A A A A S S S A DOLBY PRO LOGIC gx CINEMA S S A A A A A A A A A F DOLBY PLgx MUSIC S S A A A A A A A A A S DOLBY PLgx GAME S S A A A A A A A A A S DOLBY PLg CINEMA S S A A A A A A A A A D DOLBY PLg MUSIC S S A A A A A A A A A S DOLBY PLg GAME S S A A A A A A A A A S DOLBY PRO LOGIC S S A A A A A A A A A S Information z2 Multi-Zone DOLBY DIGITAL + PLgx CINEMA Getting Started Connections Differences in Surround Mode Names Depending on the Input Signals Troubleshooting NOTE: z1: This mode is not available when the surround back speaker setup is set to “None”. z2: This mode is not available when the surround back speaker setup is set to “1spkr” or “None”. D :Mode selectable in initial status (Amp Assign: ZONE2 b The default setting is “ZONE2”.) F : Mode selectable in initial status (Amp Assign: 7.1ch) S : Selectable mode A : Non-selectable mode b1 : When using just one surround back speaker. b2 : When using two surround back speakers. 60 ENGLISH Input signals Getting Started Connections Button DTS Surround mode Note DOLBY DIGITAL ANALOG LINEAR PCM LINER PCM (Multi ch) S S A S S S S S DTS ES DSCRT (With Flag) DTS ES MTRX (With Flag) DTS (5.1ch) DTS 96/24 DOLBY DOLBY DIGITAL EX DIGITAL EX (With Flag) (With no Flag) DOLBY DIGITAL (5.1/5/4ch) DOLBY DIGITAL (4/3ch) DOLBY DIGITAL (2ch) S S S S DIRECT DIRECT DSP SIMULATION 5CH / 7CH STEREO z3 Setup Playback Remote Control S S A S S S S S S S S S ROCK ARENA S S A S S S S S S S S S JAZZ CLUB S S A S S S S S S S S S MONO MOVIE S S A S S S S S S S S S VIDEO GAME S S A S S S S S S S S S MATRIX S S A S S S S S S S S S VIRTUAL S S A S S S S S S S S S F F A S S S S S S S S S STEREO STEREO NOTE : z3 : If the surround back speaker setup is set to “None”, then “5CH STEREO” is displayed. F : Mode selectable in initial status S : Selectable mode A : Non-selectable mode Multi-Zone Information Troubleshooting 61 ENGLISH Video Convert Monitor output S-VIDEO VIDEO HDMI COMPONENT S-VIDEO A A A A A A A A A A A S A VIDEO VIDEO VIDEO A A S A A S-VIDEO S-VIDEO S-VIDEO A A S S A S-VIDEO S-VIDEO VIDEO A S (480i/576i ~ 720p) A A A COMPONENT A A A S (480i/576i ~ 720p) A S A COMPONENT VIDEO VIDEO A S (480i/576i ~ 720p) S A A COMPONENT S-VIDEO S-VIDEO A S (480i/576i ~ 720p) S S A COMPONENT S-VIDEO VIDEO S A A A HDMI A A A S A A S HDMI VIDEO VIDEO VIDEO S A S A HDMI S-VIDEO S-VIDEO S-VIDEO S A S S HDMI S-VIDEO S-VIDEO VIDEO S S (480i/576i ~ 720p) A A HDMI COMPONENT A A S S (480i/576i ~ 720p) A S HDMI COMPONENT VIDEO VIDEO S S (480i/576i ~ 720p) S A HDMI COMPONENT S-VIDEO S-VIDEO S S (480i/576i ~ 720p) S S HDMI COMPONENT S-VIDEO VIDEO S : Signal input A : No signal 408i / 576i ~ 720p: 408i / 576i / 480p / 576p / 1080i / 720p Input signals Monitor output HDMI COMPONENT S-VIDEO VIDEO HDMI COMPONENT S-VIDEO A A A A A A A A A A A S A A A VIDEO A A S A A A S-VIDEO A A A S S A A S-VIDEO VIDEO A S A A A COMPONENT A A A S A S A COMPONENT A VIDEO A S S A A COMPONENT S-VIDEO A A S S S A COMPONENT S-VIDEO VIDEO S A A A HDMI A A A S A A S HDMI A A VIDEO S A S A HDMI A S-VIDEO A S A S S HDMI A S-VIDEO VIDEO S S A A HDMI COMPONENT A A S S A S HDMI COMPONENT A VIDEO S S S A HDMI COMPONENT S-VIDEO A S S S S HDMI COMPONENT S-VIDEO VIDEO S : Signal input A : No signal VIDEO Troubleshooting OFF A : Not output Information Video Convert VIDEO Multi-Zone COMPONENT Playback Remote Control HDMI Setup ON Input signals Getting Started Connections Relationship between Video Signals and Monitor Output A : Not output 62 ENGLISH Getting Started Connections Troubleshooting Setup If a problem should arise, first check the following: 1. Are the connections correct? 2. Is the set being operated as described in the owner’s manual? 3. Are the other components operating properly? If this unit does not operate properly, check the items listed in the table below. Should the problem persist, there may be a malfunction. In this case, disconnect the power immediately and contact your store of purchase. GGeneralH Playback Remote Control Multi-Zone Symptom Set does not operate properly. Power does not turn on, or turns off directly after it was turned on. No sound is produced from speakers. Information Cause Countermeasure • External noise or interference is • Reset the microprocessor. causing the set to malfunction. • Connection of the power cord is • Check the insertion of the power faulty. cord plug. Page 46 • Connection with the input devices or connection of the speaker cables is faulty. • Device you want to play and set input source do not match. • Master volume is turned too low. • Mute mode is set. • Headphones are connected. • No digital signals are being input. 9 ~ 17 • Check the connections. Troubleshooting • Select an appropriate input source. • Adjust the master volume to an appropriate level. • Cancel the mute mode. • Disconnect the headphones. • Select an input source for which the digital input setting has been made. • The connectors to which the • Set the input mode. digital inputs are assigned and the settable input modes do not match. Display is off. • The Dimmer setting is set to • Set to something other than “OFF”. “OFF”. “DOLBY DIGITAL” • DVD player’s digital audio output • Check the DVD player’s audio indicator does not setting is not proper. output setting. For details, read appear on display. the DVD player’s operating instructions. 63 17 39 40 40 40 26 39 40 – Symptom Power switches off suddenly while you are using the AVR-1709, the power indicator will flash in red at intervals of approximately 2 seconds. Power switches off suddenly while you are using the AVR-1709, the power indicator will flash red at intervals of approximately 0.5 seconds. Even applying power, the power display flashes red at intervals of approximately 0.5 seconds. Cause Countermeasure • The protection circuit will be • Please switch off power at once, activated depending upon the and re-apply the power after temperature rise in the internal the body temperature has fallen parts of the unit. sufficiently. • Please re-install AVR-1709 in a place having good ventilation. Page 9 • Use speakers having impedance • Please use speakers which have less than that specified. the specified impedance. • If speaker cable core wires touch each other or the core wires • Unplug the power cord, then become disconnected from their after twisting the core wires terminals, the protection circuit together tightly again, or effecting will be activated in the event of termination treatments etc, core wires coming into contact please reconnect once again. with the AVR-1709 rear panel. • The AVR-1709 amplifier circuit • Switch off the power and please has failed. contact the DENON service adviser. 9 – 9 – ENGLISH GRemote Control UnitH • Insert the batteries in the proper direction, following the polarity marks in the battery compartment. • Move the set to a place in which the remote control sensor will not be exposed to strong light. 3 • Set “Remote ID” for the main unit to “1”. 30 • Set the SOURCE CONTROL switches to the correct positions according the operation you are applying. 40, 42, 43, 47 ~ 50 Symptom No sound is produced from center speaker. 3 3 No sound is produced from surround speakers. No sound is produced from surround back speaker. • Select item other than “7.1ch” by • Select “7.1ch”. “Amp Assign” setting. • Surround back speaker setting is • Set to something other than set to “None”. “None”. • The “Parameter” – “Surround • Please set “Parameter” – Parameter” – “SB CH OUT” “Surround Parameter” – “SB settings are “OFF”. CH OUT” to settings other than “OFF”. • Surround mode not set to a mode • Select a surround playback for 6.1- or 7.1-channel playback. mode. • Subwoofer’s power not turned • Turn on the subwoofer’s power. on. • The “Subwoofer” setting at • Set to “Yes”. “Speaker Setup” is set to “No”. • The subwoofer is not properly • Check the connections. connected. • The subwoofer’s volume is • Adjust the subwoofer’s volume turned off. to an appropriate level. • Surround mode not set to • Set to the “STANDARD”(Dolby/ “ S TA N D A R D ” ( D o l b y / D T S DTS Surround) mode. Surround). 28 23 35 31, 32 – 23 9 45 31 Troubleshooting • DVD player’s audio output setting • Set the DVD player. For details, is not set to bitstream. refer to the DVD player’s operating instructions. • DVD player is not compatible • Use a DTS-compatible player. with DTS sound playback. • The AVR-1709’s “Input Mode” • Set to the “Auto” or “DTS” setting is set to other than mode. “DTS”. 32 Information No test tones are produced when main remote control unit’s TEST button is pressed. DTS sound is not output. Page 31 Multi-Zone No sound is produced from subwoofer. Cause Countermeasure • You are playing a monaural • The mode is set to something source (TV, AM radio broadcast, other than “STANDARD” (Dolby/ etc.) in the “STANDARD” (Dolby/ DTS Surround). DTS Surround) mode. • The surround mode is set to • Set to a surround playback “STEREO” or “DIRECT”. mode. Playback Remote Control Page 3 3 Setup Countermeasure • Replace with new batteries. • Operate within the specified range. • Remove the obstacle. Getting Started Connections Symptom Cause Set does not work • Batteries are worn. • You are operating outside of the properly when remote control specified range. unit operated. • Obstacle between main unit and remote control unit. • The batteries are not inserted in the proper direction, as indicated by the polarity marks in the battery compartment. • The set’s remote control sensor is exposed to strong light (direct sunlight, inverter type fluorescent bulb light, etc.). • The remote ID of the main unit and remote control unit do not match. • The SOURCE CONTROL switches are not set in the correct positions. GAudioH – – 39 64 ENGLISH Getting Started Connections GVideoH Symptom No picture appears. Setup Playback Remote Control Picture cannot be recorded. DVDs cannot be copied on a VCR. GiPodH Cause Countermeasure • The connections between the • Check the connections. AVR-1709 and monitor are faulty. • The monitor’s input setting is • Set properly. wrong. • The player is connected using the • In the case of a player which component input connectors, the is connected to component monitor is connected using the terminals, if the monitor is not video (yellow) or S-Video output connected to the component connectors. terminals, the image will not appear. Check the connections. • Input source does not match • The video conversion function recorder’s video connection does not work for the REC connector (video or S-Video). OUT connectors. Match the input source and recorder connections. • This is not a malfunction. Most movie software includes copy – prevention signals and cannot be copied. Page 10 ~ 14 – – Multi-Zone Information Troubleshooting No picture appears with HDMI connections. No sound is output from the monitor connected with HDMI connections. Cause Countermeasure • The audio signal input to the HDMI input connector cannot be played on the AVR-1709. Input – the audio signal to the digital audio input connector or analog audio input connector. • The connections to the HDMI • Check the connections. connectors are faulty. • HDMI input setting is improper. • Check the HDMI input setting. • The HDMI format of the player • Match the HDMI format of the and monitor do not match. player and monitor. • HDMI input setting is improper. • Check the HDMI input setting. Cause Countermeasure • The input source assigned to • Switch to the input source control dock for iPod is not assigned at control dock for selected. iPod. • Cable is not properly connected. • Reconnect. • Control dock for iPod’s AC • Plug the control dock for iPod’s adapter is not connected to AC adapter into a power outlet. power outlet. 13 – Page 10 10 25 10 25 Symptom “CHECK SR TUNER” is displayed in the SIRIUS mode. “ANTENNA ERROR” is displayed in the SIRIUS mode. “NO SIGNAL” is displayed in the SIRIUS mode. “INVALID CHANNEL” is displayed in the SIRIUS mode. “NO CH AVAILABLE” is displayed in the SIRIUS mode. “ACQUIRING” is displayed in the SIRIUS mode. 26 12 – Cause Countermeasure • The Sirius Tuner unit is not • Check that the connections are connected. correct. Page 15 • If the Sirius Tuner is not • Check that the connections are connected, it will be broken. correct. 15 • The signal cannot be received. • Reposition your SiriusConnect Home Tuner antenna. 42 • Channel is not present. • Select another channel. 42 • Even searching categories, • Please search for other if none of the channels are categories. present, the “Parental Lock” is on (locked). • The selected channel is not • Select another channel. currently broadcasting. • Displays while SiriusConnect Home Tuner is connected. “Call SIRIUS”* is • Channels are not subscribed to. • If you subscribe to the channel, displayed in the you can receive the channel. SIRIUS mode. “SUB UPDATED” • While updating contract – is displayed in the information. SIRIUS mode. “Code? [ ]” is • Selected channels are locked. • Please insert pass word (4 digits) displayed in the into “[ ]”. SIRIUS mode. * : After scroll displays “Call 888-539-....” twice, displays “Call SIRIUS”. 65 Page GSIRIUS Satellite RadioH GHDMIH Symptom HDMI audio signals are not output from speakers. Symptom iPod cannot be played. 42 42 – – 27 ENGLISH Getting Started Connections Specifications Receiving Range: Usable Sensitivity: 50 dB Quieting Sensitivity: S/N (IHF-A): Total harmonic Distortion (at 1 kHz): [AM] 520 kHz ~ 1710 kHz 18 µV n General Power supply: Power consumption: Maximum external dimensions: Weight: AC 120 V, 60 Hz 4.6 A 0.3 W (Standby) 434 (W) x 171 (H) x 377 (D) mm (17-3/32” x 6-47/64” x 14-27/32”) 11.3 kg (24 lbs 14.6 oz) n Main remote control unit (RC-1098) Batteries: Maximum external dimensions: Weight: R6/AA Type (two batteries) 52 (W) x 243 (H) x 21 (D) mm (2-3/64” x 9-9/16” x 53/64”) 184 g (Approx. 6.5 oz) (including batteries) Multi-Zone n Video section [FM] (note: µV at 75 Ω/ohms, 0 dBf = 1 x 10-15 W) 87.5 MHz ~ 107.9 MHz 1.0 µV (11.2 dBf) MONO 1.6 µV (15.3 dBf) STEREO 23 µV (38.5 dBf) MONO 77 dB STEREO 72 dB MONO 0.15 % STEREO 0.3 % Playback Remote Control n Tuner section • Power amplifier Front (A, B): Rated output: 80 W + 80 W (8 Ω/ohms, 20 Hz ~ 20 kHz with 0.08 % T.H.D.) 115 W + 115 W (6 Ω/ohms, 1 kHz with 0.7 % T.H.D.) Center: 80 W (8 Ω/ohms, 20 Hz ~ 20 kHz with 0.08 % T.H.D.) 115 W (6 Ω/ohms, 1 kHz with 0.7 % T.H.D.) Surround: 80 W + 80 W (8 Ω/ohms, 20 Hz ~ 20 kHz with 0.08 % T.H.D.) 115 W + 115 W (6 Ω/ohms, 1 kHz with 0.7 % T.H.D.) Surround Back: 80 W + 80 W (8 Ω/ohms, 20 Hz ~ 20 kHz with 0.08 % T.H.D.) 115 W + 115 W (6 Ω/ohms, 1 kHz with 0.7 % T.H.D.) Output connectors: Front: A or B 6 ~ 16 Ω/ohms A + B 12 ~ 16 Ω/ohms Center, Surround, Surround Back: 6 ~ 16 Ω/ohms • Analog 200 mV / 47 kΩ/kohms Input sensitivity / Input impedance: 10 Hz ~ 100 kHz — +1, –3 dB (DIRECT mode) Frequency response: 98 dB (IHF-A weighted, DIRECT mode) S/N: Setup n Audio section n Sub remote control unit (RC-1108) Frequency response: 5 Hz ~ 60 MHz — +0, –3 dB Batteries: Maximum external dimensions: Weight: Y (brightness) signal — 1 Vp-p, 75 Ω/ohms C (color) signal — 0.286 Vp-p, 75 Ω/ohms 5 Hz ~ 10 MHz — +1, –3 dB z For purposes of improvement, specifications and design are subject to change without notice. Troubleshooting Y (brightness) signal — 1 Vp-p, 75 Ω/ohms PB / CB signal — 0.7 Vp-p, 75 Ω/ohms PR / CR signal — 0.7 Vp-p, 75 Ω/ohms R03/AAA Type (two batteries) 54 (W) x 115 (H) x 23 (D) mm (2-1/8” x 4-17/32” x 29/32”) 80 g (Approx. 2.8 oz) (including batteries) 1 Vp-p, 75 Ω/ohms 5 Hz ~ 10 MHz — +1, –3 dB Information • Standard video connectors Input / output level and impedance: Frequency response: • S-Video connectors Input / output level and impedance: Frequency response: • Color component video connectors Input / output level and impedance: 66 List of preset codes / Liste de codes préréglés Blu-Ray Disc Player / DVD Player A D H J K M P S T Z Aiwa Denon Hitachi JVC Konka Magnavox Mitsubishi Panasonic Philips Pioneer Sanyo Sony Toshiba Zenith 009 014, [111]z, 121 010 006, 011 012, 013 005 004 014 005, 015, 016, 017 003, 008 018 002, 019, 020 001, 021, 022 023 Curtis Mathes Cybernex D E P R S Denon Magnavox Mitsubishi Panasonic Philips Pioneer RCA Sony 028, 029, 112 026 028 029, 030 026 028, 031 032 033, 034, 035, 036 Daytron DBX Dumont Dynatech Electrohome Electrophonic Emerson F G VDP D M Daewoo H Flsher GE Go Video Goldstar Gradiente Grundig Harley Davidson Harman Kardon Hi-Q Hitachi J JC Penny Jensen JVC VCR A Admiral Aiko Aiwa Akai C Alba Amstrad ASA Asha Audio Dynamic Audiovox Beaumark Broksonic Calix Candle Canon Capehart Carver CCE Citizen Craig K 081 095 009 026, 027, 070, 072, 082, 083, 084 055 009 042 087 005, 085 088 087 086, 093 088 006, 087, 088, 089, 090 049, 057 025, 055, 056, 071 015 095 006, 007, 087, 088, 089, 090, 095 007, 087, 088, 091, 115 PRESET CODE L M Kenwood Kodak Lloyd LXI Magnavox Magnin Marantz Marta MEI Memorex Metz MGA MGN Technology Midland Minolta Mitsubishi Motorola Montgomery Ward MTC 006, 049, 073, 080, 087, 090, 092 087 025, 055, 059, 074, 089, 093, 095, 096 025, 055 005, 085 053 009 001, 088, 097 088 001, 009, 017, 027, 086, 088, 089, 092, 093, 097, 100, 101, 102, 103, 104, 117 009, 028, 031, 053, 054, 091, 099, 115 007, 011, 049, 050, 051, 052, 073, 080, 087 047, 048 000, 006, 012, 062, 088 094 042 094 040, 062 091 009, 013, 023, 026, 058, [108]z, 109, 110, 111 004, 005, 007, 023, 028, 049, 062, 085, 087, 088 013, 026 004, 005, 006, 026, 029, 043, 044, 045, 046, 085 004, 005, 006, 026, 029, 033, 045, 085, 090 088 009, 094 088 015, 016, 042, 049, 063, 106 087 004, 005, 006, 015, 042, 049, 085, 090 088 049 009, 033, 049, 053, 060, 081, 087, 088, 091, 094, 115 123, 124, 125, 126, 127, 128 001, 017, 027, 041, 097 087 011 013, 023 001, 003, 008, 013, 014, 017, 027, 029, 039, 040, 041, 045, 097 081 001, 002, 007, 009, 049, 063, 081, 115, 117 009, 087, 094 N Multitech NAD NEC O P Nikko Noblex Optimus Optonica Panasonic Perdio Pentax Philco Philips Pilot Pioneer Q R Portland Proscan Pulsar Quartz Quasar Radio Shack Radix Randex RCA Realistic S Ricoh Salora Samsung Sanky Sansui Sanyo SBR Scott Sears Sentra Sharp Shogun Sony STS Sylvania T Symphonic Tandy Tashiko Tatung 007, 009, 011, 087, 090, 094 038 004, 005, 006, 018, 026, 029, 045, 061, 062, 085 088 087 081, 088 021 024, 049, 064, 066, 067, 068, 069, 107 009 009, 013, 023, 058, 090 015, 016, 049 015, 021, 042, 049, 105 088 005, 013, 029, 036, 037, 038, 045, 085 025, 055, 090 063, 080 060 033 034, 035, 049 001, 002, 021, 081, 087, 088, 091, 094, 097, 098, 115 088 088 007, 013, 019, 023, 058, 063, 064, 065, 073, 080, 082, 087 009, 021, 031, 033, 049, 053, 081, 087, 088, 091, 094, 097, 098 055 033, 041 007, 011, 051, 059, 070, 083, 087, 089, 113 081 005, 026, 029, 045, 061, 085, 114 032, 033, 053, 087, 091, 115, 116 042 017, 020, 086, 089, 093, 117 013, 023, 028, 031, 033, 053, 054, 088, 091, 098, 099, 115 055 001, 002, 021, 097 087 075, 076, 077, 078, 079, 121, 122 023 009, 015, 016, 017, 041, 049, 094 009, 094 009 009, 088 004, 026, 030 Teac Technics TMK Toshiba U V W X Y Z Totevision Unirech Vecrtor Research Victor Video Concepts Videosonic Wards XR-1000 Yamaha Zenith 004, 009, 026, 094 024, 049 087, 092 013, 017, 020, 041, 059, 089, 098, 099, 117 007, 087, 088 087 005, 062, 085, 089, 090 005, 045, 046, 085 005, 027, 085, 089, 090 007, 087 013, 021, 023, 087, 088, 089, 091, 094, 097, 118, 119, 120 094 004, 005, 006, 026, 062, 085 060, 078, 079 Television A Admiral Adventura Aiko Akai Alleron A-Mark Amtron Anam Anam National AOC B C Archer Audiovox Bauer Belcor Bell & Howell Bradford Brockwood Candle Capehart Celebrity Circuit City Citizen Concerto Colortyme Contec Cony Craig Crown Curtis Mathes 045, 121 122 054 016, 027, 046 062 007 061 006, 007, 036 061, 147 003, 007, 033, 038, 039, 047, 048, 049, 133 007 007, 061 155 047 045, 118 061 003, 047 003, 030, 031, 032, 038, 047, 049, 050, 122 003 046 003 029, 030, 031, 032, 034, 038, 047, 049, 050, 054, 061, 095, 122, 123 031, 047, 049 003, 047, 049, 135 013, 051, 052, 061 051, 052, 061 004, 061 029 029, 034, 038, 044, 047, 049, 053, 095, 118 D E Daewoo Daytron Dimensia Dixi Electroband Electrohome Elta Emerson F G Envision Etron Fisher Formenti Fortress Fujitsu Funai Futuretech GE Goldstar Grundy H Hitachi I J Hitachi Pay TV Infinity Janeil JBL JC Penny JCB JVC K L Kawasho Kenwood Kloss Kloss Novabeam KTV Loewe logik Luxman LXI M Magnavox Marantz Matsui Memorex Metz 027, 029, 039, 048, 049, 054, 055, 106, 107, 137 003, 049 044 007, 015, 027 046 029, 056, 057, 058, 147 027 029, 051, 059, 060, 061, 062, 118, 123, 124, 139, 148 038 027 014, 021, 063, 064, 065, 118 155 012 004, 062 004, 062 004 020, 036, 037, 040, 044, 058, 066, 088, 119, 120, 125, 147 000, 015, 029, 031, 039, 048, 051, 056, 057, 067, 068, 069, 116 062 029, 031, 051, 052, 070, 111, 112, 113, 124, [134]* 151 017, 071 122 017, 071 020, 034, 039, 040, 041, 044, 048, 050, 058, 066, 069, 076, 088, 090, 095, 125, 136, 159 046 019, 051, 052, 072, 073, 091, 117, 126 018, 046 038, 056, 057 010, 032 005, 122, 127, 131 074, 123 071 144 031 008, 014, 017, 024, 040, 044, 063, 071, 075, 076, 077, 118, 125 005, 010, 017, 030, 033, 038, 050, 056, 071, 078, 079, 085, 089, 108, 109, 110, 127, 131, 132, 145 015, 017, 071, 080 027 014, 027, 045, 083, 118, 144 160, 161, 162, 163 Midland Minutz Mitsubishi N Montgomery Ward Motorola MTC NAD National National Quenties NEC O P Nikko NTC Optimus Optonica Orion Panasonic Philco Philips Q R Pioneer Portland Price Club Proscan Proton Pulsar Quasar Radio Shack RCA S Realistic Saisho Samsung Sansui Sanyo SBR Schneider Scott Sears Sharp Siemens Signature Simpson Sony Soundesign Spectricon 001, 039, 048, 056, 057, 058, 065, 081, 083 125 066 001, 016, 039, 048, 056, 057, 058, 065, 081, 082, 083, 105 011, 020, 144, 145, 146 121, 147 031, 034, 039, 048, 095 008, 075, 076, 128 002, 036, 061, 147 002 031, 038, 039, 048, 057, 084, 086, 135, 147 054 054 128 011, 012, 093, 121 004, 139 002, 009, 017, 036, 037, 071, 141, 143, 147 005, 010, 030, 050, 051, 056, 079, 085, 127, 131, 132, 145, 147 005, 015, 017, 050, 051, 056, 078, 087, 088, 089, 131, 132, 147 124, 128, 142 054 095 040, 044, 125 035, 051, 092, 129 042 036, 037, 074, 141 011, 044, 063, 093, 118 040, 044, 125, 130, 137, 151, 152 014, 063, 093, 118 027 003, 015, 034, 053, 055, 057, 094, 095, 136, 153 139 013, 014, 021, 022, 063, 064, 081, 096 015 015 062 008, 014, 021, 022, 023, 024, 025, 040, 052, 057, 062, 063, 064, 065, 073, 075, 076, 097, 098, 125, 159 011, 012, 013, 026, 093, 099, 100, 104, 121 013 045, 144 050 043, 046, 138, 146, 150 030, 050, 062 007, 033 Squareview Supre-Macy Supreme Sylvania T Symphonic Tandy Tatung Technics Teknika Tera THOMSON Toshiba U V Universal Victor Video Concepts Viking W Wards Z Zenith Zonda 004 032, 122 046 005, 010, 017, 030, 078, 079, 085, 089, 101, 127, 131, 132, 145, 155 004, 148 012, 121 036, 124 037 001, 030, 032, 034, 052, 054, 078, 083, 095, 144, 156, 157 035, 129 165, 166 008, 014, 034, 063, 075, 076, 095, 097, 136, 158, 159 020, 066, 088 019, 073, 126 016 032, 122 005, 045, 066, 078, 085, 088, 089, 093, 102, 103, 131, 132, 148 042, 114, 115, 140, 144, 149 007 Cable A C E G H J M N O P R S ABC Archer Century Citizen Colour Voice Comtronic Eastern Garrard Gemini General Instrument Hytex Jasco Jerrold Magnavox Movie Time NSC Oak Panasonic Philips Pioneer RCA Regency Samsung Scientific Atlanta Signal SL Marx Starcom 006, [007]*, 008, 009 010, 011 011 011 012, 013 014 015 011 030, 033, 034 030, 031, 032 006 011 009, 016, 017, 026, 032 018 019 019 000, 006, 020 001, 005 011, 012, 013, 018, 021 002, 003, 022 029 015 014, 023 004, 024, 025 014 014 009 T U V Z Stargate Teleview Tocom TV86 Unika United Artists Universal Viewstar Zenith 014 014 007, 016 019 011 006 010, 011 018, 019 027, 028 M O P S Satellite Receiver T A C D W Y Z E G H J K M N P R S T Alphastar Chaparrali Dishnet Drake Echostar Dish GE General Instruments Grundig Hitachi Hughes Networkr JVC Kathrein Magnavoxl Nokia Philips Primestar Proscan RCA Realistic Sierra I Sierra g Sierra III Sony STS1 STS2 STS3 SRS4 Technisat Toshiba Uniden 054 035, 036 053 037, 038 062, 066 048, 055, 056 039, 040, 041 070, 071, 072, 073 058, 059 063, 064, 065, 069 057 074, 075, 076, 083 060 070, 080, 084, 085, 086 060 051 048, 055, 056 048, 055, 056, 068 042 036 036 036 049, 067 043 044 045 046 077, 078, 079, 081, 082 047, 050 061 CD Player A B C D E F J Aiwa Burmster Carvery Denon Emerson Fisher JVC 001, 035, 043 002 003, 035 [111]*, 044 004, 005, 006, 007 003, 008, 009, 010 018, 019 Kenwood Magnavox Marantz MCS Onkyo Optimus Philips Pioneer Sears Sony Teac Technics Wards Yamaha Zenith 011, 012, 013, 014, 017 006, 015, 035 016, 028, 035 016, 024 025, 027 017, 020, 021, 022, 023 014, 032, 033, 035 006, 022, 030 006 023, 031 002, 009, 028 016, 029, 036 035, 037 038, 039, 040, 041 042 DVD preset codes / Codes préréglés DVD 111 (default / défaut) DENON Model No. / Modéle numéro MGA DVD-555 DVD-556 DVD-557 DVD-558 DVD-755 DVD-756 DVD-757 DVD-758 DVD-900 DVD-910 DVD-955 DVD-1000 DVD-1200 DVD-1500 DVD-1710 DVD-1720 DVD-1730 DVD-1910 DVD-1920 DVD-1930CI DVD-1940CI DVD-2200 DVD-2800 DVD-2800g DVD-2900 DVD-2910 DVD-2930CI DVD-3800 DVD-3910 DVD-3930CI DVD-5900 DVD-5910CI DVD-9000 DVD-2500BT DVD-3800BD DVM-715 DVM-735 DVM-745 DVM-1800 DVM-1805 DVM-1815 DVM-1835 DVM-1845 DVM-2815 DVM-2845 DVM-4800 014 DVD-800 DVD-1600 DVD-2000 DVD-2500 DVD-3000 DVD-3300 [ ]* :Preset codes set upon shipment from the factory. *[ ] :Les codes préréglés diffèrent en fonctiom des livraison de l’usine. PRESET CODE www.denon.com Denon Brand Company, D&M Holdings Inc. Printed in China 5411 10032 207DA
advertisement
Related manuals
advertisement