Gamber-Johnson 2015+ Ford F-150 Aluminum Body, 2017+ Super Duty F-250 to F-550, 2018+ Expedition Vehicle Base Installation Guide

INSTALLATION INSTRUCTIONS
Product
Revision
7160-0554
VEHICLE BASE - FORD - F150 2015+
Form
REV. B
INST-660
Printing Spec: PS-001
DS-RISER
BASE
PARTS LIST
PART NO.
DESCRIPTION
QUANTITY
15306
VEHICLE BASE
1
11519
DS-RISER
1
7120-0215
•
1173-3812
•
3130-0052
HARDWARE BAG
•
3/8-16 X .75 HHCS
•
3/8 FLAT WASHER
1
•
•
4
4
INSTALLATION INSTRUCTIONS:
1.
2.
3.
4.
5.
6.
Attach the DS-RISER to the Base using the 3/8 bolts and wahers provided.
Remove any plastic trim that covers front and rear bolts of passenger seat.
Remove the two front seat bolts of the passenger seat and loosen the two rear
seat bolts.
Lift the seat up and slide the Base in between the seat and floor such the slots on
the base line-up with the seat bolt holes.
Install the two front seat bolts that were removed in step 3 and tighten the rear
seat bolts.
Install any plastic trim removed in step 2.
Product Mounting Disclaimer
Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage
of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson
products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brakes lines, electrical, drive train or other systems), air-bags and other safety equipment is
required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications
and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program.
© Copyright 2014 Gamber-Johnson, LLC
If you need assistance or have questions, call Gamber-Johnson at 1-800-456-6868
WARNING
• You must read and follow all of these installation instructions. Failure to follow all of these
installation instructions may result in seriuos bodily injury or death.
• Keep these installation instructions with the product and readily available in the vehicle for future
reference of other users of the product.
• Additional copies of the installation instructions can be obtained from Gamber Johnson.
• If you need assistance or have any questions, call Gamber-Johnson at 1-800-456-6868.
• Do not remove warning label from product under any circumstances.
• Before installation of any equipment always check area for routing of wires / cables and if
drilling is required check area where drilling above and below the drilling area.
• High speed vehicle turns may cause a motion attachment product to swivel, interfering with the
driver or other equipment.
• The Vehicle Base, Upper Pole, Motion Attachment and Dock or Cradle should not be positioned
in the area where the airbag will be deployed if it is activated. DO NOT postion the equipment in
front of an airbag. Equipment positioned in front of an airbag can cause serious injury or death if
and airbag was activated, such as in an accident.
• The installer and user of this product(s) are responsible for installing and using Upper Pole,
Motion Attachment and Dock or Cradle assemblies outside the airbag deployment zone. (See
Product Mounting Disclaimer Below)
• If installation of the equipment requires that the equipment be placed in front of an airbag,
deactivate the airbag in the vehicle so it cannot be activated in and accident. In order to secure
permission for deactivating the airbag in these circumstances, contact the National Highway Traffic
Safety Administration at 1-800-424-9393 to gain permission to do so. If you have any questions or
need assistance, call Gamber Johnson at 1-800-456-6868.
Product Mounting Disclaimer
Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage
of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson
products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brakes lines, electrical, drive train or other systems), air-bags and other safety equipment is
required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications
and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program.
© Copyright 2014 Gamber-Johnson, LLC
If you need assistance or have questions, call Gamber-Johnson at 1-800-456-6868