Husqvarna Z 242F Lawn Mower User manual

PDF

Document

Publicitate

Operator Manual

Z 242F

Zero Turn Mower / 967324401-00

Please read the operator manual carefully and make sure you understand the instructions before using the machine.

Gasoline containing up to 10% ethanol (E10) is acceptable for use in this machine. The use of any gasoline exceeding 10% ethanol

(E10) will void the product warranty.

Original

Instructions

CONFORMITY CERTIFICATES

USA requirements

Labels are placed on the engine and/or in the engine compartment stating that the machine will fulfill the requirements. This is also applicable to special requirements for any of the states, (California emission rules etc.). Do not remove any of these labels. Certificates can also be supplied with the machine at delivery or written in the Engine manual.

Take care of them as they are valuable documents.

WARNING! Failure to follow cautious operating practices can result in serious injury to the operator or other persons. The owner must understand these instructions, and must allow only trained persons who understand these instructions to operate the mower.

Each person operating the mower must be of sound mind and body and must not be under the influence of any mind altering substance.

When this product is worn out and no longer used, it should be returned to the reseller or other party for recycling.

WARNING! Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.

To implement improvements, specifications and designs can be altered without prior notification.

Note that no legal demands can be placed based on the information contained in these instructions.

Use only original parts for repairs. The use of other parts voids the warranty.

Do not modify or install non-standard equipment to the unit without consent from the manufacturer. Modifications to the unit may cause unsafe operations or damage the unit.

WARNING! Battery posts, terminals and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Wash hands after handling.

Orangeburg, SC Printed in U.S.A.

INTRODUCTION ............................................................... 4

Driving and Transport on Public Roads ...................... 4

Towing ......................................................................... 4

Operating .................................................................... 4

Good Service .............................................................. 5

Manufacturing Number ......................................... 5

SYMBOLS AND DECALS .................................................. 6

SAFETY ............................................................................. 7

Protecting Children ..................................................... 7

General Operation ...................................................... 7

Personal Safety Equipment ........................................ 8

Slope Operation .......................................................... 8

Safe Handling of Gasoline .......................................... 8

General Maintenance ................................................. 9

Transport ................................................................... 10

Towing ....................................................................... 10

Spark Arrestor ........................................................... 10

CONTROLS ..................................................................... 11

Control Locations ...................................................... 11

Steering Control Levers ............................................ 12

Park Brake ................................................................ 12

Ignition Switch .......................................................... 12

Throttle Control ......................................................... 13

Blade Switch ............................................................. 13

Service Meter ............................................................ 13

Choke Control ........................................................... 13

Fuse .......................................................................... 14

Seat Adjustment Lever ............................................. 14

Fuel Shut Off Valve ................................................... 14

Cutting Height Lever ................................................. 14

Bypass Linkages ...................................................... 14

Fuel Tank ................................................................... 15

Tracking .................................................................... 15

OPERATION .................................................................... 16

Training ..................................................................... 16

Steering .................................................................... 16

Before Starting .......................................................... 16

CONTENTS

Starting the Engine ................................................... 16

Running .................................................................... 17

Stopping the Engine ................................................. 18

Mowing Tips ............................................................. 18

Operating On Hills .................................................... 18

Jumper Cable Use .............................................. 19

Moving Machine By Hand ........................................ 19

MAINTENANCE ............................................................... 20

Maintenance Schedule ............................................. 20

Battery ...................................................................... 22

Park Brake ................................................................ 22

Safety System ........................................................... 23

Tire Pressures ........................................................... 23

Caster Wheels .......................................................... 23

Cutting Blades .......................................................... 24

Blade replacement ............................................. 24

V-belts ....................................................................... 24

Deck Belt Removal ............................................. 24

Adjusting the Mower Deck ....................................... 25

Leveling deck ..................................................... 25

Cleaning ................................................................... 25

LUBRICATION ................................................................. 26

Transmission ............................................................. 26

Wheel and Deck Zerks ............................................. 26

Front Wheel Mount .............................................. 26

Front Wheel Bearings ......................................... 26

Deck Spindles ..................................................... 26

TROUBLESHOOTING ..................................................... 27

STORAGE ....................................................................... 28

Winter Storage .......................................................... 28

Service ...................................................................... 28

SCHEMATIC .................................................................... 29

TECHNICAL DATA .......................................................... 30

Torque Specifications ............................................... 31

Accessories .............................................................. 31

SERVICE JOURNAL ........................................................ 32

Congratulations

Thank you for purchasing a Husqvarna ride-on mower. This machine is built for superior efficiency to rapidly mow primarily large areas. A control panel easily accessible to the operator and a hydrostatic transmission regulated by steering controls both contribute to the machine’s performance.

This manual is a valuable document. Read the contents carefully before using or servicing the machine. The following of instructions (use, service, maintenance) by all who operate this machine is important for the safety of the operator and others. It can also considerably increase the life span of the machine and increase its resale value.

If you sell your machine, be sure to give the operator manual to the new owner.

The final chapter of this operator manual provides a Service

Journal. Ensure that service and repair work are documented.

A well-kept service journal reduces service costs for the maintenance and affects the machine’s resale value. Please contact your dealer for more information. Take the operator manual along when the machine is taken to your dealer for service.

General

In this operator manual, left and right, backward and forward are used in relation to the machine’s normal driving direction.

Continuous dedication to improve our products require that specifications and design are subject to change without notice.

Driving and Transport on Public Roads

Check applicable road traffic regulations before transporting on public roads. If the machine is transported, you must always use approved fastening equipment and ensure that the machine is well anchored. DO NOT operate this machine on public roadways.

Towing

If machine is equipped with a tow hitch, use extreme caution when towing. Never allow children or others in or on the towed equipment. Make wide turns to avoid jack-knifing. Travel slowly and allow extra distance to stop.

Do not tow on sloped ground. The weight of the towed equipment may cause loss of traction and loss of control.

Follow the manufacturer's recommendation for weight limits for towed equipment. Do not tow near ditches, canals, and other hazards.

INTRODUCTION

Operating

This machine is constructed only for mowing grass on lawns and even ground without obstacles such as stones, tree stumps, etc. The machine can also be used for other tasks when equipped with special accessories provided by the manufacturer. Operating instructions for the accessories are provided with delivery. All other types of uses are incorrect.

The manufacturer’s directions concerning operation, maintenance, and repairs must be carefully followed.

Lawn mowers and all power equipment, can be potentially dangerous if used improperly. Safety requires good judgement, careful use in accordance with these instructions and common sense.

The machine must only be operated, maintained, and repaired by persons familiar with the machine’s special characteristics and who are also knowledgeable about the safety instructions.

Use only approved repair parts to maintain this machine.

Accident prevention regulations, other general safety regulations, occupational safety rules, and traffic regulations must be followed without fail.

Unauthorized modifications to the design of the machine may absolve the manufacturer from liability for any resulting personal injury or property damage.

INTRODUCTION

Good Service

Husqvarna's products are sold throughout the world and only in specialized retail stores with complete service. This ensures that you as a customer receive only the best support and service. Before the product is delivered, the machine has, for example, been inspected and adjusted by your retailer. See the certificate in the Service Journal in this operator manual.

When you need spare parts or support in service questions, warranty issues, etc., please consult the following professional:

This Manual belongs to the machine with the manufacturing number:

Manufacturing Number

The machine’s manufacturing number can be found on the printed plate affixed to the engine compartment.

Stated on the plate, from the top are:

• The machine’s type designation (I.D.).

• The manufacturer’s type number (Model).

• The machine’s serial number (Serial no.)

Please have the type designation and serial number available when ordering spare parts.

The engine’s manufacturing number is stamped on one of the valve covers.

The plate states:

• The engine’s model.

• The engine’s type.

• Code

Please have these available when ordering spare parts.

The wheel motors and hydrostatic pumps have a barcode decal affixed at the rear.

Engine

SYMBOLS AND DECALS

These symbols are found on the machine and in the operator manual.

Study them carefully so that you know what they mean.

WARNING! Xxxx xxxxxx xxxxx xxxx xxxxxxxxx xxxxxx xxxxxxxxx. xx xxxxxxxx xxxx xxxxxx.

Used in this publication to notify the reader of a risk of personal injury or death, particularly if the reader should neglect to follow instructions given in the manual.

R N

Reverse Neutral Fast Slow

IMPORTANT INFORMATION Xxxx xxxxxx xxxxx xxxx xxxxxxxxx xxxxxx xxxxxxxxx. xx xxxxxxxx xxxx xxxxxx.

Used in this publication to notify the reader of a risk of material damage, particularly if the reader should neglect to follow instructions given in the manual. Used also when there is a potential for misuse or misassembly.

Choke Fuel Warning!

Park Brake

Cut Height Low Cut Height High Use protective glasses

Use protective gloves

Do not stand here

Battery acid is corrosive, explosive and flammable

Read Operator Manual

Warning!

Keep away from the discharge deck, do not use without deflector or grass catcher

Shut off engine, remove key before performing maintenance or repair

Keep a safe distance from the machine

Do not touch parts

Use on slopes no greater than 10°

Wear hearing protection

No passengers

Whole body exposure to thrown objects

Severing of fingers and toes

Do not open or remove safety shields with engine running

Careful backing up, watch for other people

Careful going forward, watch for other people

SAFETY

Safety Instructions

These instructions are for your safety. Read them carefully.

WARNING! THIS CUTTING MACHINE IS CAPABLE

OF AMPUTATING HANDS AND FEET AND THROWING

OBJECTS. FAILURE TO OBSERVE THE FOLLOWING

SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS

INJURY OR DEATH.

WARNING! CHILDREN CAN BE SERIOUSLY

INJURED OR KILLED BY THIS EQUIPMENT. Carefully read and follow all the safety instruction that follow.

IMPORTANT INFORMATION The American Academy of

Pediatrics recommends that children be a minimum of 16 years of age befor e operating a riding lawn mower.

Protecting Children

Tragic accidents can occur if the operator is not alert to the presence of children. Children are often attracted to the machine and the mowing activity. Never assume that children will remain where you last saw them.

• Keep children out of the mowing area and in the watchful care of a responsible adult other than the operator.

• Be alert and turn machine off if a child enters the area.

• Before and while backing, look behind and down for small children.

• Never carry children, even with the blades shut off. They may fall off and be seriously injured or interfere with safe machine operation. Children who have been given rides in the past may suddenly appear in the mowing area for another ride and be run over or backed over by the machine.

• Never allow children to operate the machine.

• Use extreme care when approaching blind corners, shrubs, trees, or other objects that may block your view of a child.

General Operation

• Read, understand, and follow all instructions on the machine and in the manual before starting.

• It is recommended that someone be aware that you are mowing and can provide help in case of injury or accident.

• Anyone who operates, maintains, and/or services this machine must first read and understand this Operator

Manual. Local laws may regulate the age of the user.

The owner is responsible for training the users of this equipment.

• The owner and operator of this equipment can prevent accidents and is responsible for accidents or injuries occurring to themselves, other people and/or property.

• Do not put hands or feet near rotating parts or under the machine. Keep clear of the discharge opening at all times.

• Only allow responsible adults, who are familiar with the instructions, to operate the machine.

• Clear the area of objects such as rocks, toys, wire, etc., which could be picked up and thrown by the blades.

• Be sure the area is clear of bystanders before operating. Stop machine if anyone enters the area.

• Do not mow in reverse unless absolutely necessary. Always look down and behind before and while backing.

• Never direct discharged material toward anyone. Avoid discharging material against a wall or obstruction. Material may ricochet back toward the operator. Stop the blades when crossing gravel surfaces.

• Do not operate machine without the entire grass catcher, discharge guard, or other safety devices in place and working.

• Slow down before turning.

• Never leave a running machine unattended. Always turn off blades, move the steering control lever outward to the park brake position, stop engine and remove keys before dismounting.

• Never carry passengers. The machine is only intended for use by one person.

• Disengage blades when not mowing. Shut off engine and wait for all parts to come to a complete stop before cleaning the machine, removing the grass catcher or unclogging the discharge guard.

• Operate the machine only in daylight or good artificial light.

• Do not operate the machine while under the influence of alcohol or drugs.

• Watch for traffic when operating near or crossing roadways.

• Use extra care when loading or unloading the machine into a trailer or truck.

SAFETY

• Always wear eye protection when operating machine.

• Wear proper Personal Protective Equipment (PPE) while operating this machine, including (at a minimum) sturdy footwear, eye protection, and hearing protection. Do not mow in shorts and/or footwear with open toes.

WARNING! Do not drive up or down hills with slopes greater than 10 degrees. Do not drive across any slopes.

WARNING! When using the machine, approved personal protective equipment should be used. Personal protective equipment cannot eliminate the risk of injury but it will reduce the degree of injury if an accident does happen. Ask your retailer for help in choosing the right equipment.

• Data indicates that operators age 60 years and above are involved in a large percentage of riding mower-related injuries. These operators should evaluate their ability to operate the riding mower safely enough to protect themselves and others from serious injury.

• Follow the manufacturer’s recommendation for wheel weights or counterweights.

• Keep machine free of grass, leaves or other debris buildup which can touch hot exhaust or engine parts and burn. Do not allow the mower deck to plow leaves or other debris which can cause buildup to occur. Clean any oil or fuel spillage before operating or storing the machine.

• Allow machine to cool before storage.

• Choose a low ground speed so that you will not have to stop while on the slope.

• Do not mow on wet grass. Tires may lose traction.

• Avoid starting, stopping, or turning on a slope. If the tires lose traction, disengage the blades and proceed slowly straight down the slope.

• Keep movement on the slopes slow and gradual. Do not make sudden changes in speed or direction, which could cause machine to roll over.

• Use extra care while operating machine with grass catchers or other attachments; they can affect the stability of the machine.

• Do not use on steep slopes.

• Do not try to stabilize the machine by putting a foot on the ground.

• Do not mow near drop-offs, ditches, or embankments.

The machine could suddenly roll over if a wheel is over the edge or the edge caves in.

Personal Safety Equipment

• Make sure that first aid equipment is close at hand when using the machine.

• Never use the machine when barefoot.

• Always wear protective shoes or boots, preferably with steel toe caps.

• Always wear approved protective glasses or a full visor when assembling or driving.

• Always wear gloves when handling the blades.

• Never wear loose clothing that can get caught in moving parts.

• Use ear protectors to avoid damage to hearing.

Slope Operation

Slopes are a major factor related to loss of control and tip-over accidents, which can result in severe injury or death. Operation on all slopes requires extra caution. If you cannot back up the slope or if you feel uneasy on it, do not mow it.

• Mow up and down slopes

(10 degrees maximum), not across.

• Watch for holes, ruts, bumps, rocks, or other hidden objects. Uneven terrain could overturn the machine.

Tall grass can hide obstacles.

Safe Handling of Gasoline

WARNING! The engine and the exhaust system become very hot during operation. There is a risk for burns if touched. Allow engine and exhaust system to cool before refueling.

To avoid personal injury or property damage, use extreme care in handling gasoline. Gasoline is extremely flammable and the vapors are explosive.

• Extinguish all cigarettes, cigars, pipes, and other sources of ignition.

• Use only approved gasoline containers.

• Never remove gas cap or add fuel with the engine running. Allow engine to cool before refueling.

• Never fuel the machine indoors.

• Never store the machine or fuel container where there is an open flame, spark or pilot light such as on a water heater or other appliance.

• Before you begin refueling, minimize the risk of static electricity by touching a metal surface.

• Never fill containers inside a vehicle or on a truck or trailer bed with plastic liner. Always place containers on the ground away from the vehicle when filling.

• Never overfill fuel tank. Replace gas cap and tighten securely.

SAFETY

• Remove gas-powered equipment from the truck or trailer and refuel it on the ground. If this is not possible, refuel such equipment with a portable container, rather than from a gasoline dispenser nozzle.

• Keep the nozzle in contact with the rim of the fuel tank or container opening at all times until fueling is complete. Do not use a nozzle lock-open device.

• If fuel is spilled on clothing, change clothing immediately.

• Do not start the engine near spilled fuel.

• Never use gasoline as a cleaning agent.

• If leaks arise in fuel system, the engine must not be started until problem has been resolved.

• Check the fuel level before each use and leave space for the fuel to expand, as the heat from the engine and the sun may otherwise cause the fuel to expand and overflow.

CAUTION! Use protective glasses for maintenance work.

General Maintenance

• Never use the machine indoors or in spaces lacking proper ventilation. The exhaust fumes contain carbon monoxide, an odorless and poisonous lethal gas.

• Make sure that the equipment is in good condition and that all nuts and bolts, especially those fastening the blade attachments, are properly tightened and torqued.

• Maintain or replace safety and instruction labels as necessary.

• Never interfere with the intended function of a safety device or reduce the protection provided by a safety device.

Check their proper operation regularly. NEVER operate a machine with a safety device that does not function properly.

WARNING! The engine must not be started when the driver’s floor plate or any protective plate for the mower deck’s drive belt is removed.

• Check grass catcher components and the discharge guard frequently and replace with manufacturer’s recommended parts when necessary.

• Do not change the settings of governors and avoid running the engine with overly high engine speeds. If you run the engine too fast, machine components could be damaged.

• To reduce the risk of fire, keep machine free of grass, leaves or other debris buildup. Clean oil or fuel spills and remove any fuel-soaked debris. Allow machine to cool before storing.

• Stop to inspect the equipment if you run over or into anything. If necessary, make repairs before starting.

• Never make adjustments or repairs with the engine running.

• The blades are sharp and can cause cuts and gashes.

Wrap the blades or use protective gloves when handling them.

• Never work with the starter circuit if there is spilled fuel.

• Ensure that the fuel filler cap is mounted tightly and no flammable substances are stored in an open vessel.

• Sparking can occur when working with the battery and the heavy cables of the starter circuit. This can cause battery explosion, fire or eye injury. Sparking will not occur after the grounding cable (normally negative, black) is removed from the battery.

• Disconnect the grounding cable from the battery first and reconnect it last.

• Do not make a bridge short circuit across the starter relay to run the starter.

• Be very careful when handling battery acid. Acid on skin can cause serious corrosive burns. If you spill battery acid on your skin, rinse immediately with water.

• Acid in the eyes can cause blindness, contact a doctor immediately.

• Be careful when servicing the battery. Explosive gases form in the battery. Never perform maintenance on the battery when smoking or near open flames or sparks.

The battery can explode and cause serious injury or damage.

• The machine is tested and approved only with the equipment originally provided or recommended by the manufacturer. Only use approved repair parts for the machine.

• Check the park brake’s functionality regularly. Adjust and service as necessary.

• The mulch blades should only be used in familiar areas when higher quality mowing is desired.

• Regularly clean deck and underside of deck, avoid spraying engine and electrical components with water.

WARNING! The battery contains lead and lead compounds, chemicals that are considered to cause cancer, birth defects, and other reproductive system damage. Wash your hands after handling the battery.

Transport

WARNING! Use extreme caution when loading the machine into a truck or trailer using ramps. There is the possibility of serious injury or death if the machine falls off the ramps.

IMPORTANT INFORMATION The park brake is not sufficient to lock the machine in place during transport.

Ensure that the machine is well fastened to the transport vehicle. Always reverse the machine onto the transport vehicle to avoid tipping it over.

• The machine is heavy and can cause serious crushing injuries. Be extra cautious when it is loaded on or unloaded from a vehicle or trailer.

• Use full width ramps for loading machine into a trailer or truck.

• Use an approved trailer to transport the machine. Activate the park brake by securing the steering controls in the outward position with elastic or ratcheting straps. Turn off the fuel supply. Fasten the machine down with approved devices such as bands, chains or straps.

• Both front and rear tie down straps should be used and directed down and outward from the machine.

• Do not operate this machine on public roadways.

• Check and abide by local traffic regulations before transporting the machine on any road.

• Do not tow this machine, it may cause damage to the drive system.

• Do not tow any trailers, etc. with this mower. They may jackknife or overturn, causing damage to the mower and possible serious injury to the operator.

• Load the unit onto truck or trailer by driving up ramps of suitable strength using a slow speed. Do not lift! The machine is not intended to be lifted by hand.

• When loading or unloading this machine, do not exceed the maximum recommended operation angle of 10 O .

SAFETY

Towing

If machine is equipped with a tow hitch, use extreme caution when towing. Never allow children or others in or on towed equipment..

Make wide turns to avoid jack-knifing. Travel slowly and allow extra distance to stop. Do not tow on sloped ground. The weight of the towed equipment may cause loss of traction and loss of control.

Follow the manufacturer’s recommendation for weight limits for towed equipment. Do not tow near ditches, canals, and other hazards.

Spark Arrestor

This mower is equipped with an internal combustion engine and should not be used on or near any unimproved forested, bush covered or grassy lands unless the engine’s system is equipped with a spark arrestor meeting applicable local or state laws (if any).

Federal laws apply on federal lands.

If a spark arrestor is used, it should be maintained in effective working order by the operator.

A spark arrestor for the muffler is available through your authorized Husqvarna dealer.

WARNING! Engine exhaust and certain vehicle components contain or emit chemicals considered to cause cancer, birth defects, or other reproductive system damage.

The engine exhaust contains carbon monoxide, which is an odorless, colorless, poisonous gas. Do not use the machine in enclosed spaces.

CONTROLS

This operator manual describes the Husqvarna Zero Turn

Rider. The rider is fitted with a Kawasaki four-stroke overhead valve engine.

Transmission from the engine is made via a belt-driven hydraulic pumps. Using the left and right steering controls, the flow is regulates the direction and speed.

Control Locations

9 10

11 12

1. Steering/Brake levers

2. Tracking adjustment, left side

3. Deck lift

4. Fuses

5. Bypass linkages

6. Fuel shut off valve

7. Fuel tank

8. Choke control

9. Throttle control

10. Service meter

11. Ignition switch

12. Blade switch

13. Seat adjustment lever

Steering Control Levers

CONTROLS

WARNING! The machine can turn very rapidly if one steering control is moved much further forward than the other.

Park Brake

The machine’s speed and direction are continuously variable using the two steering controls. The steering controls can be moved forward or backward about a neutral position.

Furthermore, there is a neutral position, which is locked if the steering controls are moved outward.

When both controls are in the neutral position (N), the machine stands still.

By moving both controls an equal amount forward or backward, the machine moves in a straight line forward or backward respectively.

In order, for example, to turn right while moving forward, move the right control towards the neutral position. The rotation of the right wheel is reduced and the machine turns to the right.

Zero turn can be achieved by moving one control backward

(behind the neutral position) and carefully moving the other steering control forward from its neutral position. The rotation direction when zero turning is determined by which steering control is moved backward behind the neutral position. If the left steering control is pulled backward, the machine turns to the left. Use extra care when using this maneuver.

If the steering controls are in uneven positions when standing still or do not fit in the slots for moving the controls outward, they can be adjusted.

The park brake is integrated with the steering control levers.

Move the levers outward from the neutral position to engage the park brake.

To release the park brake, rotate both steering control levers inwards to the neutral position. Do not attempt to operate the unit without both levers being inwards out of the engaged position or machine components could be damaged.

IMPORTANT INFORMATION The machine must stand absolutely still when applying the park brake. Always set the park brake before dismounting. Release the park brake before moving the mower.

Ignition Switch

Forward

Neutral

Park

Brake

Reverse

The ignition switch is placed on the control panel and is used to start and stop the engine.

Throttle Control

CONTROLS

Service Meter

The throttle control regulates the engine speed and the rate of rotation of the blades, assuming the blade switch is pulled out.

See Blade Switch.

To increase or decrease the engine speed, the control is moved forward or back respectively.

Avoid idling the engine for long periods, as there is a risk of fouling the spark plugs.

USE FULL THROTTLE WHEN

MOWING , for best mower performance and battery charging.

The service meter displays the total number of hours the engine has run and indicates when the engine and mower need servicing.

After every 50 hours of operation, an oil can icon will appear and stay on for two hours, before an automatic reset occurs.

To manually reset the meter, turn the key off and on five times at one second intervals. To service the engine and mower, see the Service Journal of this manual.

Note: The service meter operates (clocks hours) only when the engine is running. Be sure to turn the key off when the unit is not in use, to prevent meter hours from accumulating.

Blade Switch Choke Control

To engage the mower deck, pull the knob out; mower blades are disengaged when the knob is pressed down.

The choke control is used for cold starts to provide the engine with a richer fuel mixture.

For cold starts the control should be pulled up.

Fuse

CONTROLS

Cutting Height Lever

The 20 amp primary fuse is located on the left hand side of the machine. It is accessed by tilting the seat forward. The fuse is a flat pin type used in automobiles.

To set the deck cutting height, pull the cutting height lever inwards and move it to the desired height notch.

Seat Adjustment Lever

IMPORTANT INFORMATION Always raise the deck to the highest position for transport.

IMPORTANT INFORMATION To obtain an even cutting height, it is important that the air pressure in all tires is 15 psi / 103 kPa / 1 bar.

The seat can be adjusted lengthways. When making adjustments, the lever under the right side of the seat is pulled up, after which the seat can be moved backward or forward.

Fuel Shut Off Valve

Bypass Linkages

Transaxle bypass linkages must be engaged when pushing or pulling the mower. The release levers are located on each side of the rear of the unit below the rear engine guard. See Moving

Machine By Hand in the Operation section.

The fuel shut off valve is located at the right rear of the seat.

The valve is off when the handle tab is turned perpendicular to the fuel line.

WARNING! Bypass linkages are located close to the muffler. To prevent burns, the engine should be shut off and allowed to cool before the bypass linkage levers are handled.

Fuel Tank

CONTROLS

IMPORTANT INFORMATION Experience indicates that alcohol blended fuels (called gasohol, ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel the next season. See Storage for additional information. Never use engine or carburetor cleaners in the fuel tank or permanent damage may occur.

Tracking

WARNING! Gasoline is highly flammable.

Observe caution and fill the tank outdoors (see the safety instruction).

WARNING! The engine and the exhaust system, become very hot during operation. There is a risk for burns if touched. Allow engine and exhaust system to cool before refueling.

WARNING! Fill to bottom of filler neck. Do not overfill. Wipe off any spilled oil or fuel. Do not store, spill or use gasoline near an open flame.

Read the safety instructions before refueling. The machine has one fuel tank, just behind the console. The tank capacity is 3½ gallons (13.25 litres).

Regularly check the gas cap gasket for damage and keep the cap properly tightened.

The engine will run on a minimum of 87-octane unleaded gasoline (no oil mix). Environmentally adapted alkylate gasoline can be used. See also Technical Data concerning ethanol fuel. Methanol fuel is not allowed. Do not use E85 alcohol based fuel. Damage to engine and components may occur.

When operating in temperatures below 32° F. (0° C.), use fresh, clean winter grade gasoline to insure good cold weather starting.

If the mower is not tracking straight, check the air pressure in both rear tires. Recommended air pressure for the rear tires is

15 psi (1 bar).

1. Tracking adjustments are made using the tracking bolts.

The tracking bolts act as limiting devices for the motion control levers when in the full-forward position.

2. For preliminary tracking adjustment, move unit to an open, unobstructed area such as an empty parking lot or open field.

3. Using a ½" wrench, back the tracking bolts out until flush with nut.

4. Test operate unit by driving it at full throttle and the full forward position on both motion control levers. Gradually turn in the tracking bolt on the right hand side until the unit noticeably starts drifting right.

5. Drive forward at full throttle with both motion control levers in the full forward position. Gradually turn in the left tracking bolt until unit tracks straight.

Read the Safety section and following pages, if you are unfamiliar with the machine.

Training

Due to unique steering capabilities, zero turn mowers are far more maneuverable than typical riding mowers.

This section should be reviewed in its entirety prior to attempting to move the mower under its own power. When first operating the mower or until becoming comfortable with controls, use a reduced throttle speed and reduced ground speed. DO NOT move control levers to the furthest forward or reverse positions during initial operation.

First time users should become familiar with the mower’s movement on a hard surface, such as concrete or blacktop

PRIOR to attempting to operate on turf. Until the operator becomes comfortable with the mower controls and zero turning capability, overly aggressive maneuvers may damage turf.

Steering

To move forward and backward

The direction and speed of the mower’s movements are effected by the movement of the control lever(s) on each side of mower. The left control lever controls the left wheel. The right control lever controls the right wheel.

First time users should push the mower (see Moving the

Machine By Hand in the Operation section) to an open, flat area without other people, vehicles or obstacles nearby. To move the unit under its own power, the operator must sit in the seat and start the engine (see Before Starting in the Operation section). Adjust the engine speed to idle and disengage the park brake by moving the steering control levers inward. Do not engage the blades. As long as the control levers have not been moved forward or backwards, the mower will not move.

Slowly move both control levers slightly forward. This will allow the mower to move forward in a straight line. Pull the control levers back to the neutral position and the mower should stop moving.

Pull back slightly on control levers, allowing the mower to move backwards. Push the control levers forward to the neutral position and mower should stop moving.

To turn to the right

While moving in a forward direction, pull the right lever back towards the neutral position while maintaining the position of the left lever, this will slow the rotation of the right wheel and cause the machine to turn in that direction.

To turn to the left

While moving in a forward direction pull the left lever back towards the neutral position while maintaining the position of the right lever, this will slow the rotation of the left wheel and cause the machine to turn in that direction.

To zero turn

While moving in a forward direction, first pull both control levers back until the mower stops or slows dramatically.

Then by alternating one lever slightly to the forward position and the other in the reverse position, complete the turn.

OPERATION

Before Starting

1. Read the sections on Safety and Controls before starting the machine.

2. Perform the daily maintenance before starting (see

Maintenance Schedule in the Maintenance section).

3. Check that there is sufficient fuel in the fuel tank.

4. Adjust the seat to the desired position.

The following conditions must be fulfilled before the engine can be started:

• The blade switch must be pressed down into the disengaged position.

• Both steering / park brake controls must be in the locked

(outer) position.

WARNING! Engine exhaust and certain vehicle components contain or emit chemicals considered to cause cancer, birth defects or other reproductive system damage.

The engine exhaust contains carbon monoxide, which is a odorless, colorless, poisonous gas. Do not use the machine in enclosed spaces.

Starting the Engine

1. Sit on the seat.

2. Raise the mower deck to the highest position.

3. Disengage the mower blades by pressing the blade switch downwards.

OPERATION

4. Move the steering / park brake controls out to the locked position.

8. Set the engine speed with the throttle. Allow the engine to run at a moderate speed, approximately mid throttle, for a short time before use.

9. USE FULL THROTTLE WHEN MOWING .

Running

1. Release the park brake by pulling the steering / park brake controls inwards to the neutral position.

NOTE: The mower is equipped with an operator presence system. When the engine is running, any attempt by the operator to leave the seat without first setting the park brake will shut off the engine.

2. Lower the mower deck to the desired cutting height.

5. Move the throttle to the middle position. If the engine is cold, the choke control should be pulled up.

6. Press in and turn the ignition key to the start position.

7. When the engine starts, immediately release the ignition key back to the run position. Push the choke control in gradually when the engine has started.

3. Move throttle control to full throttle (rabbit symbol).

4. Engage the mower deck by pulling the blade switch up.

5. Rotate control levers inward and slowly move both control levers slightly forward to move forward in a straight line.

WARNING! Make sure that no one is near mower when engaging blade switch.

Make sure the work area is free from objects that could be thrown by the rotating blades.

IMPORTANT INFORMATION Do not run the starter for more than 5 seconds each time. If the engine does not start, wait approximately 10 seconds before retrying.

WARNING! Do not drive up or down hills with slopes greater than 10 degrees. Do not drive across slopes.

OPERATION

Stopping the Engine

1. Move the throttle to the minimum position (tortoise symbol).

2. Move the steering / park brake controls outward from the neutral position.

3. Disengage the mower deck by pressing the blade switch down.

• When mowing large areas, start by turning to the right so that clippings will discharge away from shrubs, fences, driveways, etc. After one or two rounds, mow in the opposite direction making left hand turns until finished.

4. Raise the mower deck to the highest position.

If the engine has been worked hard, allow it to idle at least 60 seconds to attain a normal operating temperature before stopping. To prevent fouling the spark plugs, avoid idling the engine for longer periods.

5. Turn the ignition key to the stop position. Remove key.

Always remove key when leaving the mower to prevent unauthorized use.

IMPORTANT INFORMATION Leaving the ignition switch in any other position than OFF will cause the battery to be discharged.

Mowing Tips

• Observe and flag rocks and other fixed objects to avoid collisions.

• Begin with a high cutting height and reduce it until the desired mowing result is attained. The average lawn should be cut to 2½" during the cool season and over 3" during the hot months. For healthier and better looking lawns, mow often after moderate growth. For best cutting performance, grass over 6" in height should be mowed twice. Make the first cut relatively high, the second to the desired height.

• The mowing result will be best with a high engine speed

(blades rotate rapidly) and low speed (rider moves slowly).

If the grass is not too long and dense, the driving speed can be increased without negatively affecting the mowing result.

• The finest lawns are obtained by mowing often. The lawn becomes more even and the grass clippings more evenly distributed over the mown area. The total time taken is not increased as a higher operating speed can be used without poor mowing results.

• Avoid mowing wet lawns. The mowing result is poorer because the wheels sink into the soft lawn, clumps build, and grass clippings fasten under the cowling.

• Hose the mower deck underside with water after each use.

When cleaning, the mower deck shall be raised into the transport position. Make sure the mower is cooled and the engine is off.

• Use compressed air to clean top surface of the deck.

Avoid flooding water on top surface, engine and electrical components.

• When the mulching kit is used, it is important that the mowing interval is frequent.

Operating On Hills

Read the Safety Instructions Driving on Slopes in the Safety section.

• The slowest speed possible should be used before starting up or down hills.

• Avoid stopping or changing speed on hills.

• If stopping is absolutely necessary, pull steering controls into the neutral position and the push to the outside of the unit to engage the park brake.

• To restart movement, move the steering controls back to the neutral position.

• Press forward to regain forward motion.

• Make all turns slowly.

WARNING! Never drive the rider on terrain that slopes more than 10 degrees. Mow slopes up and down, never side to side. Avoid sudden directional changes.

Weak Battery

If the battery is too weak to start the engine, it should be recharged. (See Battery in the Maintenance section.)

If jumper cables are used for emergency starting, follow this procedure:

Jumper Cable Use

1. Connect each end of the RED cable to the POSITIVE (+) terminal on each battery, taking care not to short against chassis.

2. Connect one end of the BLACK cable to the NEGATIVE (-) terminal of the fully charged battery.

3. Connect the other end of the BLACK cable to a good

CHASSIS GROUND on the mower with the discharged battery, away from the fuel tank and battery.

To remove cables, reverse order

1. Remove BLACK cable first from chassis and then from the fully charged battery.

2. Remove RED cable last from both batteries.

OPERATION

Moving Machine By Hand

When pushing or pulling the mower, engage the EZT bypass linkages. The EZT bypass linkages are located on the rear of the frame, below the rear engine guard.

1. Raise the deck into the highest cutting position.

2. Move the steering / park brake controls inwards to the neutral position.

3. Pull the EZT bypass linkages up and out of the keyhole slots. Release the levers with the head outside the frame and held in the bypass position.

CAUTION! Lead-acid batteries generate explosive gases. Keep sparks, flame and smoking materials away from batteries. Always wear eye protection when around batteries.

IMPORTANT INFORMATION The mower is equipped with a 12-volt negative grounded system. The other vehicle must also be a 12-volt negative grounded system. Do not use your mower to start other vehicles.

4. To reengage the EZT’s to drive, reverse the above procedure.

Load the machine into truck or trailer by driving slowly up the ramps. DO NOT LIFT! The machine is not intended to be lifted by hand.

WARNING! Bypass linkages are located close to the muffler. To prevent burns, the engine should be shut off and allowed to cool before the bypass linkage levers are handled.

•

WARNING! Make no adjustments without: the engine stopped, the ignition key removed, the park brake activated

WARNING! Use extreme caution when loading the machine into a truck or trailer using ramps. There is the possibility of serious injury or death if the machine falls off the ramps.

MAINTENANCE

Maintenance Schedule

The following is a list of maintenance procedures that must be performed on the machine. For those points not described in this manual, visit an authorized service workshop. An annual service carried out by an authorized service workshop is recommended to maintain your machine in the best possible condition and to ensure safe operation.

Read General Maintenance in the Safety section.

MAINTENANCE

Check the park brake

Check the engine’s oil level (every refueling)

Check the safety system

Check for fuel and oil leakages

Check/clean the engine’s cooling air intake

Check the mower deck

Check for loose hardware (screws, nuts)

Clean under the mower deck

Start the engine and blades, listen for unusual sounds

Check for damage

Thoroughly clean around the engine

Clean around belts, belt pulleys

Check the tire pressures

Check battery connections

Sharpen 3) / Replace mower blades

Clean the engine’s cooling air intake 2)

Clean the foam air cleaner prefilter 2)

Clean the paper air cleaner filter cartridge 2)

Check/adjust the park brake

Inspect muffler/spark arrestor

1) First change after 8-10 hours. When operating with a heavy load or at high ambient temperatures, replace every 50 hours.

2) In dusty conditions, cleaning and replacement are required more often.

3) Performed by authorized service workshop.

●

= Described in this manual

♦

= Not described in this manual

■

= Refer to the engine manufacturer's manual

Before

●

♦

●

■

Daily

After

♦

●

■

●

At least once each year 25

Maintenance interval in hours

50 100 300

■

♦

●

■

♦

MAINTENANCE

MAINTENANCE

Check/adjust throttle cable

Check the condition of belts, belt pulleys

Change the engine oil 1)

Replace the engine oil filter

Clean/replace the spark plugs

Replace the fuel filter

Replace paper air filter 2)

Check the caster wheels (every 200 hours)

Replace the air cleaner’s foam pre-filter 2)

Check/adjust the mower deck

Check the engine valve clearance 3)

Perform the 300-hour service 3)

1) First change after 8-10 hours. When operating with a heavy load or at high ambient temperatures, replace every 50 hours.

2) In dusty conditions, cleaning and replacement are required more often.

3) Performed by authorized service workshop.

●

= Described in this manual

♦

= Not described in this manual

■

= Refer to the engine manufacturer's manual

Daily

Before After

At least once each year

●

■

●

■

●

♦

Maintenance interval in hours

50 300 100

■

●

■

●

WARNING! Before performing any service or adjustment checklist

• Engage the park brake.

• Place the Blade-switch in the disengaged position.

• Turn the ignition switch to OFF position and remove the key.

• Make sure the blades and all moving parts have completely stopped.

●

♦

WARNING! Escaping hydraulic oil under pressure can have sufficient force to penetrate the skin, causing serious injury. If injured by escaping fluid, see a doctor at once. Serious infection or reaction can develop if proper medical treatment is not administered immediately.

MAINTENANCE

Battery

Your mower is equipped with a maintenance free battery that does not need servicing. However, periodic charging of the battery with an automotive type battery charger will extend its life.

• Keep battery and terminals clean.

• Keep battery bolts tight.

• See chart for charging times.

STANDARD

BATTERY

12.6V

12.4V

12.2V

12.0V

11.8V

STATE APPROXIMATE BATTERY CHARGING TIME*

TO FULL CHARGE AT 80 O F / 27 O C

CHARGE

100%

75%

50%

25%

50 Amps

Maximum Rate at:

30 Amps 20 Amps 10 Amps

- FULL CHARGE -

20 min.

45 min.

65 min.

35 min.

75 min.

115 min.

48 min.

95 min.

145 min.

0% 85 min.

150 min.

195 min.

*Charging time depends on battery capacity, condition, age, temperature and efficiency of charger

90 min.

180 min.

280 min.

370 min.

Cleaning battery and terminals

Corrosion and dirt on the battery and terminals can cause the battery to lose power.

1. Disconnect BLACK battery cable first, then the RED battery cable and remove the battery from the machine.

2. Rinse the battery with plain water and dry.

3. Clean terminals and battery cable ends with wire brush until shiny.

4. Coat terminals with grease or petroleum jelly.

5. Reinstall battery.

Replacing battery

1. Lift seat and rotate forward.

2. Using two ½" wrenches disconnect BLACK battery cable then RED battery cable.

3. Position deck to lowest setting.

4. From underside of frame, remove the nuts that secure the battery hold-down.

WARNING! Do not short battery terminals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery, remove metal bracelets, wristwatch bands, rings, etc.

Positive terminal must be connected first to prevent sparks from accidental grounding.

IMPORTANT INFORMATION Do not attempt to open or remove caps or covers. Adding or checking level of electrolyte is not necessary.

Always use two wrenches for the terminal screws.

CAUTION! Always wear eye protection when around batteries.

5. Carefully remove the battery from the mower.

6. Install new battery with cable terminals routed toward the center of the battery.

7. Reinstall battery hold-down and secure with nuts removed in Step 4.

8. Reconnect RED battery cable to positive (+) battery terminal with bolt and hex nut.

9. Connect BLACK grounding cable to negative (-) battery terminal with remaining hex bolt and hex nut

10. Replace terminal boot cover.

11. Lower seat

Park Brake

Visually check that no damage is found on the steering control levers, links or switches belonging to the park brake. Perform a standstill test and check that there is sufficient braking action.

To adjust the park brake, contact the Husqvarna service workshop.

IMPORTANT INFORMATION The machine must be absolutely standing still when applying the park brake.

WARNING! Faulty adjustment will result in reduced braking ability and can cause an accident.

MAINTENANCE

Safety System

The machine is equipped with a safety system that prevents starting or driving under the following conditions.

The engine can only be started when:

• the mower deck is disengaged.

• the steering / park brake controls are in the outer, locked neutral position.

Tire Pressures

All tires should be at 15 psi / 103 kPa / 1 bar.

IMPORTANT INFORMATION DO NOT add any type of tire liner or foam fill material to the tires. Excessive loads created by foam filled tires will cause premature failures.

Only use O.E.M. specified tires.

Make daily inspections to ensure that the safety system works by attempting to start the engine when one of the conditions is not met. Change the conditions and try again.

If the machine starts when one of these conditions is not met, turn the machine off and repair the safety system before using the machine again.

Make sure the engine stops when the park brake is not engaged and the operator leaves the seated position.

Check that the engine stops if the mower blades are engaged and the driver temporarily moves off the drivers seat.

Caster Wheels

Check every 200 hours. Check that wheels rotate freely. If wheels do not rotate freely take the unit to your dealer for service.

Foam filled tires or solid tires will void the warranty.

Removal and installation

Remove nut and caster bolt. Pull the wheel out of the yoke and take care of the spacers. Install in reverse order. Tighten caster bolt.

IMPORTANT INFORMATION To be able to drive, the driver must sit in the seat and the steering / park brake controls must be moved into the engaged (outer) position.

Otherwise the engine will stop.

Hardware

Check daily. Inspect the entire machine for loose or missing hardware.

MAINTENANCE

Cutting Blades

For the best mowing results, it is important that blades are well sharpened and not damaged.

Replace blades that have been bent or cracked when hitting obstacles.

Let the service workshop decide whether a blade with large nicks can be repaired/ground or must be replaced. Balance the blades after sharpening.

Check the blade mounts.

CAUTION! Blades are sharp. Protect your hands with gloves and/or wrap blades with a heavy cloth when handling.

The sharpening of blades should be carried out by an authorized service workshop.

V-belts

Check every 100 hours of operation. Check for severe cracking and large nicks.

NOTE: The belt will show some small cracks in normal operation.

The belts are not adjustable. Replace belts if they begin to slip from wear.

Deck Belt Removal

1. Park on a level surface. Apply park brake.

2. Lower the deck into the lowest cutting position.

3. Remove bolts from belt shields and remove shields.

4. Remove any dirt or grass that may have accumulated around the cutter housings and entire deck surface.

5. Loosen the nut securing the belt guide. Pull the belt guide up out of the idler arm.

6. Push inward on the idler arm to release the tension on the belt. Blade replacement

1. Remove blade bolt by turning counter clockwise .

2. Install new or resharpened blade with stamped GRASS

SIDE facing towards ground/grass (down) or THIS SIDE

UP facing deck and cutter housing.

3. Seat the blade's opening firmly onto the cutter housing.

4. Tighten blade bolt securely.

5. Torque blade bolt to 45-60 ft/lbs (60-81 Nm).

IMPORTANT INFORMATION Special blade bolt is heat treated. Replace with a Husqvarna bolt if required. Do not use lower grade hardware than specified.

7. Carefully lift the belt over the top of the cutter housing pulleys and remove belt from the deck.

Deck Belt Installation

NOTE: For ease in installing the deck belt, refer to the routing decal on the top of the deck.

1. Wrap the deck belt around the electric clutch pulley located on the engine shaft.

2. Route the belt forward and up onto the deck.

3. Place belt around spring loaded idler pulley.

4. Wrap the belt around the stationary idler pulley and around the mandrel housings.

5. Push inward on the idler arm and carefully route belt over stationary idler pulley. Once the belt is properly routed, slowly release the idler arm to tension belt.

6. Double check belt routing to make sure it matches the decal affixed to the deck , and the belt does not have any twist. Correct if needed.

7. Set the loosened belt guide into the idler arm hole and tighten the pulley bolt. Replace belt shields on both mandrel housings and secure with fasteners.

MAINTENANCE

Adjusting the Mower Deck

NOTE: This will place the mower deck in a standard measurement position. Depending on the type of grass being mowed or environmental conditions, additional adjustments may be required to achieve the desired cut.

Leveling deck

Adjust the deck while the mower is on a level surface.

Make sure the tires are inflated to the correct pressure. See

Technical Data / Transmission. If tires are under or over inflated, the deck cannot be properly adjusted. Raise the deck to the highest (transport) position.

The deck should be adjusted slightly higher in the rear.

NOTE: To insure accuracy of leveling procedure, mower deck drive belt must be installed prior to leveling deck.

1. Wear heavy gloves. Turn each blade tip to align front to rear with the deck side-to-side.

adjustment. With an adjustable wrench, loosen the rear jam nut on the front suspension linkage. Make adjustment to level with the front lift link nut. Clockwise raises the front of the mower, counter clockwise will lower the front. Adjust the nut until rear blade tip is ¼" to 3 /

" higher than the front blade tip.

2. Measure from the floor surface up to the bottom of the blade tip on the discharge side of the mower deck.

Record the measurement.

3. Move to the opposite side, check that measurement is the same. If adjustment is required—with a ¾" or adjustable wrench, turn the lift link adjustment nuts on either side counter clockwise to lower or clockwise to raise. Adjust until both measurements are equal.

Cleaning

Regular cleaning, especially under the mower deck, will increase the machine’s life-span. Make it a habit to clean the machine directly after use (after it is cooled), before the debris sticks.

Do not spray water on the top of the mower deck. Use compressed air to clean the top side of mower deck. Regularly clean the underside of the deck with normal water pressure.

Do not use a high pressure washer or steam cleaner. Avoid spraying engine and electrical components with water.

For models fitted with a cleanout port, attach the quick connect

(from the accessory packet) to any garden hose. After mowing, snap the hose to the cleanout port and turn on water supply.

Restart the mower and engage the blades to use the spinning action to wash away debris. Make sure the hose is away from the mower blades.

Do not rinse hot surfaces with cold water. Let unit cool before washing.

4. Turn either blade to align with the deck front-to-rear. If the front blade tip does not measure ¼" to 3 /

" higher in the rear, remove the foot plate access the front deck

CAUTION! Use protective glasses when cleaning and washing.

LUBRICATION

Wheel and Deck Zerks

Use only good quality bearing grease.

Grease from well-known brand names (petrochemical companies, etc.) usually maintains a good quality.

Front Wheel Mount

Lubricate 3-4 strokes with a grease gun on each set of wheel bearings.

Front Wheel Bearings

Lubricate 3-4 strokes with a grease gun on each set of wheel bearings.

12/12 Every year

1/52 Every Week

1/365 Every day

Lubricate with grease gun

Filter change

Oil change

Level check

General

Remove the ignition key to prevent unintentional movements during lubrication.

When lubricating with an oil can, it must be filled with engine oil.

When lubricating with grease, unless otherwise stated, use a high grade molybdenum disulphide grease.

For daily use, the machine should be lubricated twice weekly.

Wipe away excess grease after lubrication.

It is important to avoid getting lubricant on the belts or the drive surfaces of the belt pulleys. Should this happen, attempt to clean them with spirits. If the belt continues to slip after cleaning, the belt must be replaced. Gasoline or other petroleum products must not be used to clean belts.

Deck Spindles

Lower the cutting deck completely.

Lubricate with a grease gun, 2-3 strokes per spindle.

IMPORTANT INFORMATION Use minimal lubrication and remove excess lubricant so that is does not come into contact with belts or belt pulley drive surfaces.

Transmission

The transmission is maintenance free with no need for level checks or oil changes. If a leak occurs, replace the unit or contact your Husqvarna dealer.

TROUBLESHOOTING

Problem / Cause

Engine will not start

Blade switch is engaged

Steering controls are not locked in the outer position

Battery is dead

Contamination in the carburetor or fuel line

Fuel supply shutoff valve is closed

Clogged fuel filter or fuel line

Ignition system faulty

Starter does not turn the engine over

Battery is dead

Poor contact of the battery terminal cable connections

Blown fuse

Fault in the starter safety circuit. See Safety System in the

Maintenance Section

Safety switches are not fully inserted

Engine runs rough

Faulty carburetor

Clogged fuel filter or jet

Choke control is pulled out with a warm engine

Clogged ventilation valve on the fuel cap

Fuel tank nearly empty

Fouled spark plugs

Rich fuel mixture or fuel-air mixture.

Wrong fuel type

Water in fuel

Clogged air filter

Engine seems weak

Clogged air filter

Fouled spark plugs

Carburetor incorrectly adjusted

Air trapped in hydraulic system

Machine vibrates

Blades are loose

Blades are incorrectly balanced

Engine is loose

Engine overheats

Clogged air intake or cooling fins

Engine overloaded

Poor ventilation around engine

Defective engine speed regulator

Too little or no oil in the engine

Contamination in the carburetor or fuel line

Fouled spark plugs

Battery not charging

Poor contact of the battery terminal cable connections

Charging lead is disconnected

Machine moves slowly, unevenly, or not at all

Park brake on

Bypass linkages engaged

Drive belt for the transmission is slack or has come off

Air trapped in hydraulic system

Mower deck not engaging

Drive belt for the mower deck has come loose

Contact for the electromagnetic coupling has loosened

Blade switch is faulty or has come loose from cable contact

Blown fuse

Transaxle leaks oil

Damaged seals, housing, or gaskets

Air trapped in hydraulic system

Uneven mowing results

Different air pressure in tires on the left and right sides.

Bent blades

Suspending for the mower deck is uneven

Blades are dull

Driving speed too high

Grass is too long

Grass collected under the mower deck

STORAGE

Winter Storage

The machine should be readied for storage at the end of the mowing season or if it will not be in use for more than 30 days.

Fuel allowed to stand for long periods of time (30 days or more) can leave sticky residues that can plug the carburetor and disrupt engine function.

Fuel stabilizers are an acceptable option to prevent the sticky residues that can occur during storage.

Add stabilizer to the fuel in the tank or in the storage container.

Always use the mixing ratios specified by the manufacturer of the stabilizer. Run the engine for at least ten minutes after adding the stabilizer so that it reaches the carburetor. Do not empty the fuel tank and the carburetor if stabilizer has been added.

WARNING! Never store an engine with fuel in the tank indoors or in poorly ventilated spaces where fuel vapor can come in contact with open flames, sparks, or a pilot light such as in a boiler, hot water tank, clothes dryer, etc.

Handle the fuel with care. It is very flammable and can cause serious personal injury and property damage. Drain the fuel into an approved container outdoors and store far away from open flame or sources of ignition. Never use gasoline for cleaning. Use a degreaser and warm water.

To ready the machine for storage:

1. Thoroughly clean the machine, especially under the mower deck. Touch up damage to the paint and spray a thin layer of oil on the underside of the mower deck to avoid corrosion.

2. Inspect the machine for worn or damaged parts and tighten any nuts or screws that may have become loose.

3. Change the engine oil; dispose of properly.

4. Empty the fuel tanks or add a fuel stabilizer. Start the engine and allow it to run until the carburetor is drained of fuel or the stabilizer has reached the carburetor.

5. Remove the spark plug and pour about a tablespoon of engine oil into the cylinder. Turn over the engine so that the oil is evenly distributed and then refit the spark plug.

6. Lubricate all grease zerks, joints and axles.

7. Remove the battery. Clean, charge and store the battery in a cool place, but protect it from direct cold.

8. Store the machine in a clean, dry place and cover it for extra protection.

Service

When ordering spare parts, please specify the purchase year, model, type, and serial number.

Always use genuine Husqvarna spare parts.

An annual check-up at an authorized service workshop is a good way to ensure that your machine performs its best the following season.

28 28

SCHEMATIC

TECHNICAL DATA

Engine

Manufacturer

Type

Power

Lubrication

Fuel

Fuel tank capacity

Cooling

Air filter

Alternator

Starter

Transmission

Transmission

Steering control

Speed forward

Speed reverse

Brakes

Front caster tires

Rear tires, turf pneumatic

Tire pressure

The power rating as declared by the engine manufacturer is the average gross power output at the specified RPM of a typical production engine for the engine model measured using SAE Standards for engine gross power. Refer to the engine manufacturer engine specifications.

Briggs & Stratton

Endurance Commercial

22 1)

Pressure with oil filter

Min 87 octane unleaded (Max ethanol 10%, Max MTBE 15%)

3½ gallons / 13.25 litres

Air cooled

Standard

12V

Electric

Hydrostatic transaxles

Dual levers, foam gripped

0-6.5 mph / 0-10.5 km/h

0-3.5 mph / 0-5.6 km/h

Mechanical park brake

11 x 6-5

18 x 8.5-8

15 PSI / 103 kPa / 1 bar

Frame

Cutting Width

Cutting Height

Uncut Circle

Number of Blades

Blade Length

Nose Roller

Sprung Seat

Hinged Arm Rests

Service Meter

Blade Engagement

Deck Construction

Productivity

Dimensions

Weight

Base Machine Length

Base Machine Height

Base Machine Width

Overall Width, Chute Up

Overall Width, Chute Down

42" / 107cm

1.5" - 4" / 3.8 - 10.2 cm

21" / 53.3 cm

Yes

Standard

Optional

Digital

Electromagnetic Clutch

Fabricated

2.2 acres/h / 8,093 m 2 /h

580 lbs / 263 kg

75" / 191 cm

40" / 102 cm

41.5" / 106 cm

48" / 122 cm

56" / 142 cm

TECHNICAL DATA

Engine crankshaft bolt

Deck pulley bolts

Lug nuts

Blade bolt

Torque Specifications

75 ft/lb (102 Nm)

60 ft/lb (81 Nm)

Standard ¼" fasteners

Standard 5 /

" fasteners

Standard 3 /

" fasteners

Standard 7 /

" fasteners

Standard ½” fasteners

9 ft/lb (12 Nm)

18 ft/lb (25 Nm)

33 ft/lb (44 Nm)

52 ft/lb (70 Nm)

80 ft/lb (110 Nm)

Accessories

Collection system

Grade

HEX HEAD CAP SCREWS

The torque values shown should be used as a general guideline when specific torque values are not given.

U.S. Standard Hardware

SAE Grade 5 SAE Grade 8

Size ft./lbs Nm ft./lbs Nm

Flangelock Screw w/Flangelock Nut ft./lbs Nm

5 /

3 /

7 /

110

102

149

115

165 9 /

5 /

150

250

203

339

225

370

7 /

378 512 591

1 1 /

782 1060 1410

** Grade 5 - Minimum commercial quality (lower quality not recommended)

102

156

224

305

502

801

1912

Grade

Size

M18

M20

M22

M24

M27

M10

M12

M14

M16

M7 ft./lbs

142

195

276

353

530

13.5

43.5

70.5

108

1.5

5.2

8.2

Grade 8.8

Metric Standard Hardware

Grade 10.9

Nm ft./lbs Nm

193

264

374

478

719

146

2.2

4.5

7.5

18.8

35.2

62.2

100

147

202

275

390

498

735

274

373

529

675

996

136

199

16 ft./lbs

Grade 12.9

242

330

471

596

904

21.8

43.5

119

176

2.7

5.2

8.2

328

447

639

808

1226

102

161

239

3.7

SERVICE JOURNAL

Action

Delivery Service

Charge the battery

Adjust the tire pressure of all wheels to 15 PSI (1 bar)

Mount the steering controls in the normal position

Connect the contact box to the cable for the seat’s safety switch

Check that the right amount of oil is in the engine

Adjust the position of the steering controls

Fill with fuel and open the fuel shut off valve

Start the engine

Check that there is drive to both wheels

Check the mower deck adjustment

Check:

Safety switch for the park brake

Safety switch for the mower deck

Safety switch in the seat

Safety switch in the steering controls

Park brake functionality

Driving forward

Driving backward

Engaging the blades

Check the idle speed

Check the engine high idle speed

Inform the customer about:

Need and advantages of following the service schedule

Need and advantages of leaving machine for service every 300 hours

Effects of service and maintaining a service journal on machine’s resale value

Application areas for mulching

Fill in the sales papers, etc.

Delivery service has been carried out

No remaining notes

Certified:

Date, mtr reading, stamp, sign q q q q q q q q q q q q q q q q q q q q q q q q

Action

After the First 10 Hours

Change engine oil

SERVICE JOURNAL

Date, mtr reading, stamp, sign q

25-Hour Service

Check the fuel pump’s air filter

Sharpen/Replace mower blades if required

Check the tire pressures

Check battery cables

Lubricate according to lubrication chart

Check / clean the engine’s cooling air intake

Clean the air cleaner’s foam pre-filter

50-Hour Service

Perform the 25-hour service

Clean / replace the air cleaner’s paper filter cartridge

(shorter intervals for dusty operating conditions)

Change engine oil

Lubricate according to lubrication chart

Check/adjust the park brake

Date, mtr reading, stamp, sign q q q q q q q

Date, mtr reading, stamp, sign q q q q q

SERVICE JOURNAL

Action

100-Hour Service

Perform the 25-hour service

Perform the 50-hour service

Change the engine oil filter

Clean/replace the spark plugs

Replace the fuel filter

Check V-belts

Check / tighten caster wheel axle bolts (every 200 hours)

Change the air filter’s paper cartridge

Change hydraulic pump oil and filter. (200 hours)

Date, mtr reading, stamp, sign q q q q q q q q q

Action

300-Hour Service

Perform the 25-hour service

Perform the 50-hour service

Perform the 100-hour service

Check / adjust the mower deck

Clean the combustion chamber and grind the valve seats

Check the engine valve clearance

Replace the air cleaner’s foam pre-filter

Date, mtr reading, stamp, sign q q q q q q q

SERVICE JOURNAL

Action

At Least Once Each Year

Clean the engine’s cooling air intake (25 hours)

Replace the air cleaner’s foam pre-filter (300 hours)

Replace the air filter’s paper cartridge

Change the engine oil (50 hours)

Replace the engine oil filter (100 hours)

Check / adjust the cutting height

Check / adjust the park brake (50 hours)

Clean / change the spark plugs (100 hours)

Change the fuel filter (100 hours)

Check the engine valve clearance

Date, mtr reading, stamp, sign q q q q q q q q q q

Action

SERVICE JOURNAL

Date, mtr reading, stamp, sign

Action

SERVICE JOURNAL

Date, mtr reading, stamp, sign

www.husqvarna.com

115 73 24-27 Rev A

2014-10-15

Publicitate