Cisco Elastic Services Controller Install and Upgrade Guide

PDF

Document

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

First Published: 2021-06-04

Americas Headquarters

Cisco Systems, Inc.

170 West Tasman Drive

San Jose, CA 95134-1706

USA http://www.cisco.com

Tel: 408 526-4000

800 553-NETS (6387)

Fax: 408 527-0883

THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS,

INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND,

EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.

THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT SHIPPED WITH

THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE OR LIMITED WARRANTY,

CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.

The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB's public domain version of the UNIX operating system. All rights reserved. Copyright © 1981, Regents of the University of California.

NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED “AS IS" WITH ALL FAULTS.

CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, THOSE OF

MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF DEALING, USAGE, OR TRADE PRACTICE.

IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING, WITHOUT

LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO OR ITS SUPPLIERS

HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, network topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentional and coincidental.

Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: http://www.cisco.com/go/trademarks . Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1110R)

C O N T E N T S

P R E F A C E

C H A P T E R 1

P A R T I

C H A P T E R 2

C H A P T E R 3

About This Guide xi

Audience xi

Terms and Definitions xi

Related Documentation xiii

Elastic Services Controller Overview 1

Installing Cisco Elastic Services Controller on OpenStack 3

Prerequisites 5

Virtual Resource Requirements 5

Software Requirements 6

Preparing for the Installation 6

Installing Cisco Elastic Services Controller on OpenStack 7

Installation Scenarios 7

Main Components of Cisco Elastic Services Controller Setup 8

Installing Cisco Elastic Services Controller Using the QCOW Image 8

Additional Installation Options 12

Managing Root Certificates in Cisco Elastic Services Controller 16

Enabling/Disabling the Root Certificate Validation 16

Adding a Root Certificate 17

Removing a Root Certificate 17

Managing Root Certificates During the Upgrade 18

Managing Keystore in Cisco Elastic Services Controller 18

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide iii

Contents

C H A P T E R 4

C H A P T E R 5

C H A P T E R 6

C H A P T E R 7

C H A P T E R 8

ESCADM Keystore Commands 18

Using a Bootable Volume in ESC Installation 20

Installing High Availability Active/Standby 21

High Availability Active/Standby Overview 21

ESC Active/Standby Architecture 22

How High Availability Works 22

Deploying ESC High Availability Active/Standby 23

Deploying ESC in High Availability Active/Standby Mode on Internal Storage 24

Deploying ESC in High Availability Active/Standby Mode on Replicate External Storage 25

Configuring the Northbound Interface Access 26

Configuring ESC HA Active/Standby with Multiple Interfaces 26

Configuring the ESC HA Active/Standby Virtual IP Address 27

Configuring the ESC L3 HA Active/Standby With BGP 28

Important Notes 31

Troubleshooting High Availability Active/Standby 32

Cisco Elastic Services Controller Active/Active High Availability Overview 33

Cisco Elastic Services Controller Active/Active HA Overview 33

ESC Active/Active Architecture 34

Installing Active/Active High Availability Cluster 35

Setting up the User Configuration 35

Validating Active/Active High Availability Cluster Post Installation 37

Adding Default VIM Connector to the Active/Active High Available Cluster 38

Adding BGP in an Active/Active Cluster 38

Managing Cluster in ESC Active/Active High Availability 41

Configuring GEO in Active/Active High Availability 43

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Contents

C H A P T E R 9

C H A P T E R 1 0

P A R T I I

C H A P T E R 1 1

C H A P T E R 1 2

C H A P T E R 1 3

Transition Conditions 43

Verifying GEO Services 45

Active/Active GEO HA Failure Injection Limitations 46

DRBD Encryption for ESC Active/Standby and Active/Active HA Data Replication 49

DRBD Encryption for ESC HA Data Replication 49

ESC HA with DRBD Encryption 49

Upgrading ESC Active/Active High Availability 51

Backing up the Database 51

Removing the Old VMs 52

Installing a New ESC Active/Active VM 52

Restoring the ESC Database 53

Installing Cisco Elastic Services Controller on VMware vCenter 55

Prerequisites 57

Virtual Resource and Hypervisor Requirements 57 vCenter Resources 57

Important Notes 58

Installing Cisco Elastic Services Controller on VMware vCenter 61

Preparing to Install Cisco Elastic Services Controller 61

Installing the Elastic Services Controller Using the OVA Image 62

Installing Elastic Services Controller Using OVF Tool 64

Powering on Cisco Elastic Services Controller Virtual Machine 66

Next Steps: Cisco Elastic Services Controller Virtual Machine 67

Logging in to Cisco Elastic Services Controller Portal 67

Configuring the Virtual Machine to Automatically Power Up 67

Installing High Availability 69

High Availability Active/Standby Overview 69

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide v

Contents

P A R T I I I

C H A P T E R 1 4

P A R T I V

C H A P T E R 1 5

P A R T V

C H A P T E R 1 6

P A R T V I

C H A P T E R 1 7

How High Availability Active/Standby Works 69

Deploying ESC High Availability Active/Standby with User Data (HA Active/Standby Pair) 70

Deploying ESC High Availability Active/Standby (Standalone Instances) 74

Important Notes for ESC HA Active/Standby 75

Troubleshooting High Availability Active/Standby 75

Installing Cisco Elastic Services Controller on VMware vCloud Director 77

Installing Cisco Elastic Services Controller on VMware vCloud Director 79

Uploading the ESC OVA file into a Catalog in VMware vCloud Director 79

Deploying ESC vApp on vCD Web Client 79

Adding the VIM Connectors 80

Adding Self-Signed Certificate 80

Installing Cisco Elastic Services Controller on a Kernel-based Virtual Machine (KVM) 81

Installing Cisco Elastic Services Controller on a Kernel-based Virtual Machine 83

Installing Cisco Elastic Services Controller in a Kernel-based Virtual Machine 83

Preparing to Install Cisco Elastic Services Controller on a Kernel-based Virtual Machine 83

Installing Elastic Services Controller on a Kernel-Based Virtual Machine 85

Next Steps: Cisco Elastic Services Controller Kernel-based Virtual Machine 86

Logging in to Cisco Elastic Services Controller Portal 86

Verifying ESC installation for a Kernel-based Virtual Machine (KVM) 86

Troubleshooting Tips 86

Installing Cisco Elastic Services Controller on Amazon Web Services (AWS) 87

Installing Cisco Elastic Services Controller on Amazon Web Services 89

Prerequisites 89

Installing the Elastic Services Controller Instance in AWS 90

Installing Cisco Elastic Services Controller on Cisco Cloud Services Platform 2100 93

Installing Cisco Elastic Services Controller on Cisco Cloud Services Platform 2100 95

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Contents

P A R T V I I

C H A P T E R 1 8

Prerequisites 95

Installing the Elastic Services Controller Instance in CSP 2100 95

ESC HA Active/Standby Installation 100

List of Variables Used in CSP 2100 Sample Files 104

Post Installation Tasks 107

Post Installation Tasks 109

Changing the ESC Password 109

Changing the ConfD Netconf/CLI Administrator Password Using the Command Line Interface

110

Creating Readonly User Group for ConfD in ESC 110

Changing Linux Account Password 112

Changing the ESC Portal Password 112

Configuring Pluggable Authentication Module (PAM) Support for Cisco Elastic Services Controller

113

PAM Authentication Service Configurations and User Groups 114

Adding PAM User to an ESC Service/Component 114

Configuring Cisco Elastic Services Controller as Identity Management Client 115

Configuring Cisco Elastic Services Controller as the Identity Policy and Audit Client 116

Authenticating REST Requests 117

REST Authentication 117

Enabling ETSI REST Authentication 118

Changing the REST Interface Password 118

Changing the ETSI REST Interface Password 119

Sending an Authorized REST Request 119

Sending an Authorized ETSI REST Request 120

Configuring Openstack Credentials 120

Enabling Barbican Client in ESC 126

Reconfiguring ESC Virtual Machine 126

Reconfiguring Rsyslog 126

Reconfiguring NTP 128

Reconfiguring DNS 128

Reconfiguring Hosts 129

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide vii

Contents

P A R T V I I I

C H A P T E R 1 9

C H A P T E R 2 0

Reconfiguring Timezone 129

Verifying ESC Configurations and Other Post-Install Operations 129

Logging in to the ESC Portal 132

Upgrading Cisco Elastic Services Controller 135

ESC in Maintenance Mode 137

Setting ESC in a Maintenance Mode 137

Using the escadm Tool 137

Setting ESC in an Operation Mode 138

Backup the Database from the ESC Standalone Instances 138

Backup the Database from the ESC HA Active/Standby Instances 140

Restoring ESC Database 141

Upgrading Cisco Elastic Services Controller 143

Upgrading Standalone ESC Instance 144

Deploy the ESC for Upgrade 145

Restoring the ESC Database 145

Important Notes: 146

Upgrading ESC HA Active/Standby Instances 146

Deploying the ESC HA Active/Standby nodes for Upgrade 146

Restoring the ESC Database on New Active and Standby ESC Instances 146

Upgrading VNF Monitoring Rules 148

In-Service Upgrade of the ESC HA Active/Standby Nodes in OpenStack 148

In-Service upgrade in OpenStack using ESC RPM packages 148

In-Service upgrade in OpenStack using ESC qcow2 Image 149

In-Service Upgrade of ESC HA Active/Standby Nodes in Kernel-Based Virtual Machine (KVM) 152

In-Service Upgrade in KVM using ESC RPM packages 152

In-Service Upgrade in KVM using ESC OVA Image 153

In-Service Upgrade of the ESC HA Active/Standby Nodes in VMware 156

In-Service upgrade in VMware using ESC RPM packages 156

In-Service upgrade in VMware using ESC qcow2 Image 157

In-Service Upgrade of the ESC HA Active/Standby Nodes in CSP 160

viii

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

P A R T I X

C H A P T E R 2 1

A P P E N D I X A

A P P E N D I X B

Troubleshooting Cisco Elastic Services Controller Installation 163

Troubleshooting ESC Issues 165

Viewing ESC Log Messages 165

General Installation Errors 170

ESC Failover Scenarios 173

Cisco Elastic Services Controller Installer Arguments 175

List of Variables Used in CSP 2100 Sample Files 187

Contents

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide ix

Contents x

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

About This Guide

This guide describes the installation requirements, procedures, and upgrade procedures for Cisco Elastic

Services Controller.

•

Audience, on page xi

Audience

This guide is designed for network administrators responsible for provisioning, configuring, and monitoring

VNFs. Cisco Elastic Services Controller (ESC) and the VNFs whose lifecycle it manages are deployed in a

Virtual Infrastructure Manager (VIM). Currently OpenStack, VMware vCenter, VMware vCloud Director,

CSP 2100 / 5000, and Amazon Web Services (AWS) are the supported VIMs. The administrator must be familiar with the VIM layer, vCenter, OpenStack and AWS resources, and the commands used.

Cisco ESC is targeted for Service Providers (SPs) and Large Enterprises. ESC helps SPs reduce cost of operating the networks by providing effective and optimal resource usage. For Large Enterprises, ESC automates provisioning, configuring and monitoring of network functions.

Terms and Definitions

The below table defines the terms used in this guide.

Table 1: Terms and Definitions

Terms

AWS

ESC

ETSI

Definitions

Amazon Web Services (AWS) is a secure cloud services platform, offering compute, database storage, content delivery and other functionalities.

Elastic Services Controller (ESC) is a Virtual Network Function Manager (VNFM), performing lifecycle management of Virtual Network Functions.

European Telecommunications Standards Institute (ETSI) is an independent standardization organization that has been instrumental in developing standards for information and communications technologies (ICT) within Europe.

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide xi

About This Guide

Terms Definitions

ETSI

Deployment

Flavour

A deployment flavour definition contains information about affinity relationships, scaling, min/max VDU instances, and other policies and constraints to be applied to the VNF instance.

The deployment flavour defined in the VNF Descriptor (VNFD) must be selected by passing the flavour_id attribute in the InstantiateVNFRequest payload during the instantiate VNF

LCM operation.

KPI

MSX

NFV

ESC High Availability (HA) is a solution for preventing single points of ESC failure and achieving minimum ESC downtime.

Key Performance Indicator (KPI) measures performance management. KPIs specify what, how and when parameters are measured. KPI incorporates information about source, definitions, measures, calculations for specific parameters.

Cisco Managed Services Accelerator (MSX) is a service creation and delivery platform that enables fast deployment of cloud-based networking services for both Enterprises and Service

Providers customers.

Network Function Virtualization (NFV) is the principle of separating network functions from the hardware they run on by using virtual hardware abstraction.

NFVO

NSO

OpenStack

Compute

Flavor

Service

VDU

VIM

VNF

NFV Orchestrator (NFVO) is a functional block that manages the Network Service (NS) lifecycle and coordinates the management of NS lifecycle, VNF lifecycle (supported by the

VNFM) and NFVI resources (supported by the VIM) to ensure an optimized allocation of the necessary resources and connectivity.

Cisco Network Services Orchestrator (NSO) is an orchestrator for service activation which supports pure physical networks, hybrid networks (physical and virtual) and NFV use cases.

Flavors define the compute, memory, and storage capacity of nova computing instances. A flavor is an available hardware configuration for a server. It defines the size of a virtual server that can be launched.

A service consists of a single or multiple VNFs.

The Virtualisation Deployment Unit (VDU) is a construct that can be used in an information model, supporting the description of the deployment and operational behaviour of a subset of a VNF, or the entire VNF if it was not componentized in subsets.

The Virtualized Infrastructure Manager (VIM) adds a management layer for the data center hardware. Its northbound APIs are consumed by other layers to manage the physical and virtual resources for instantiation, termination, scale in and out procedures, and fault & performance alarms.

A Virtual Machine (VM) is an operating system OS or an application installed on a software, which imitates a dedicated hardware. The end user has the same experience on a virtual machine as they would have on dedicated hardware.

A Virtual Network Function (VNF) consists of a single or a group of VMs with different software and processes that can be deployed on a Network Function Virtualization (NFV)

Infrastructure.

xii

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

About This Guide

Related Documentation

Terms

VNFC

VNFM

Definitions

A Virtual Network Function Component is (VNFC) a composite part of the VNF, synonymous with a VDU, which could be implemented as a VM or a container.

Virtual Network Function Manager (VNFM) manages the life cycle of a VNF.

Elastic Services Controller Overview

•

Elastic Services Controller Overview, on page 1

Elastic Services Controller Overview

Cisco Elastic Services Controller (ESC) is a Virtual Network Functions Manager (VNFM), which performs life cycle management of Virtual Network Functions (VNFs). ESC provides agent-less and multi vendor VNF management by provisioning virtual services, and monitoring their health and load. ESC provides the flexibility to define monitoring rules, and associate actions to be triggered based on the outcome of these rules. As a

VNFM, in addition to the typical lifecycle management operations, ESC also supports automatic VM recovery when a VM fails and performs automatic scaling in and out functions. ESC fully integrates with Cisco and other third party applications.

• As part of the Cisco Orchestration Suite, ESC is packaged with Cisco Network Services Orchestrator

(NSO), and available within Cisco Solution, Managed Services Accelerator Solution (MSX).

• As a Specialized Virtual Network Function Manager (SVNFM), ESC tightly integrates with the Cisco

Mobility VNFs.

• ESC can also be utilized as a Generic Virtual Network Function Manager (GVNFM) to provide lifecycle management for both Cisco and third-party VNFs.

ESC is deployed in a virtual machine within OpenStack, VMware vCenter, KVM or AWS and manages its

VNFs in a Virtual Infrastructure Manager (VIM).

Elastic Services Controller as a VNF Manager targets the virtually managed services and all service provider

NFV deployments such as virtual video, WiFi, authentication and others.

ESC can manage both basic and complex VNFs . Basic VNFs include a single VM such as a vFW, vRouter and others.

Complex VNFs include multiple VMs that are orchestrated as a single entity with dependencies between them.

IPv6 Support

Elastic Services Controller provides IPv6 support on OpenStack for:

• VNF Management

• HA— ESC manages VNFs on IPv4 and IPv6 (OpenStack and KVM only).

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Elastic Services Controller Overview

Elastic Services Controller provides IPv6 support for northbound interface (for example, NFVO to VNFM), and southbound interface (for example, VNFM to VNF). In order to support both northbound and southbound

IPv6 concurrently, the following pre-requisites must be met:

• OpenStack cloud computing is set up and configured for ipv6, including the endpoints (that are ipv6 based).

• The OpenStack cloud computing must contain a Controller, endpoints, and a few Compute hosts, with an ipv6 management and os_api based networks.

• The ESC default security group rules support the IPv6 traffic.

Note When you are deploying a VM, you can attach an out-of-band port of an IPv6 subnet to a VM. However, if you are deleting this VM, you cannot attach the same IPv6 address to another VM due to a known OpenStack issue.

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

P A R T

Installing Cisco Elastic Services Controller on

OpenStack

•

Prerequisites, on page 5

•

Installing Cisco Elastic Services Controller on OpenStack, on page 7

•

Installing High Availability Active/Standby, on page 21

•

Cisco Elastic Services Controller Active/Active High Availability Overview, on page 33

•

Installing Active/Active High Availability Cluster, on page 35

•

Managing Cluster in ESC Active/Active High Availability, on page 41

•

Configuring GEO in Active/Active High Availability, on page 43

•

DRBD Encryption for ESC Active/Standby and Active/Active HA Data Replication , on page 49

•

Upgrading ESC Active/Active High Availability, on page 51

C H A P T E R

Prerequisites

The following sections detail the prerequisites for installing Cisco Elastic Services Controller:

•

Virtual Resource Requirements, on page 5

•

Software Requirements, on page 6

•

Preparing for the Installation, on page 6

Virtual Resource Requirements

The following table lists the virtual resource requirements for Cisco Elastic Services Controller:

ESC

Deployment

ESC

Standalone

Number of

ESC VMs

Virtual CPU per ESC VM

Virtual

Memory (GB) per ESC VM

Virtual Hard

Disk (GB)per

ESC VM

Number of total VMs

Supported

8 40 1000

VIM

All supported

VIMs

ESC

Active/Standby

ESC

Active/Active

ESC GEO

2500

5000

All supported

VIMs

OpenStack

Only

OpenStack

Only

Note

The Active/Active HA and Geo HA deployment can accommodate up to 60 GB of hard disk while provisioning the NFVI resources.

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Installing Cisco Elastic Services Controller on OpenStack

Software Requirements

Software Requirements

The following table lists the software requirements on OpenStack:

Requirements Description

Supported Browsers

OpenStack Version

Google Chrome 44.x or later

Any of the following:

• Train

• Ocata (V2 and V3)

• Queens (Keystone V3)

Preparing for the Installation

Before you perform the installation, ensure that you are prepared by reviewing this checklist:

Requirements Your Information/ Notes

For Pre-installation

Configuration

QCOW image location

QCOW image

VM per Instance

IP address

Subnet mask

Hostname

Domain name

Gateway IP address

Admin password

ESC Release Package

ESC.qcow2

bootvm.py

An image file for booting up the ESC instance

The installation script is compatible with python 2.7.6 and Python 3.4

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

C H A P T E R

Installing Cisco Elastic Services Controller on

OpenStack

This chapter describes how to install Cisco Elastic Services Controller on OpenStack and includes the following sections:

•

Installation Scenarios, on page 7

•

Main Components of Cisco Elastic Services Controller Setup, on page 8

•

Installing Cisco Elastic Services Controller Using the QCOW Image, on page 8

•

Managing Root Certificates in Cisco Elastic Services Controller, on page 16

•

Managing Keystore in Cisco Elastic Services Controller, on page 18

•

Using a Bootable Volume in ESC Installation, on page 20

Installation Scenarios

The following sections briefly describe some of the common deployment scenarios that are addressed by ESC.

Cisco Elastic Services Controller can be installed in different modes as per the requirement. These different modes are configured during installation. The following sections briefly describe some of the common deployment scenarios that are addressed by ESC.

ESC Standalone

In the standalone scenario, a single active VM is deployed for ESC.

ESC with HA

ESC supports High Availability (HA) in the form of Active/Standby and Active/Active models. For

Active/Standby model, two ESC instances are deployed in the network to prevent ESC failure and to provide

ESC service with minimum interruption. If the active ESC instance fails, the standby instance automatically takes over the ESC services. ESC HA resolves the following single point failures of ESC:

• Network failures

• Power failures

• Dead VM instance

• Scheduled downtime

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Installing Cisco Elastic Services Controller on OpenStack

Main Components of Cisco Elastic Services Controller Setup

• Hardware issues

• Internal application failures

Note Installing or upgrading software on the ESC VM is not supported. For further assistance, contact Cisco TAC.

For more information on Installing ESC HA Active/Standby, see

Installing Cisco Elastic Services Controller

Using the QCOW Image, on page 8

and Installing Cisco Elastic Services Controller on VMware vCenter.

For more information on the Active/Active model, see ESC HA Active/Active Overview Chapter.

Main Components of Cisco Elastic Services Controller Setup

The Cisco Elastic Service Controller (ESC) setup has the following components:

• Virtual Infrastructure Manager —Elastic Services Controller (ESC) and its VNFs are deployed in a

Virtual Infrastructure Manager (VIM). This might have one or more underlying physical nodes.

• ESC Virtual Machine —The ESC VM is a VM that contains all the services and processes used to register and deploy services. This includes the ESC Manager and all other services. ESC provides Netconf

API, REST API, and Portal as north bound interfaces to communicate with ESC. ESC VM contains CLI to interact with ESC VM. There are two CLI, one uses the REST API and the other uses Netconf API.

Installing Cisco Elastic Services Controller Using the QCOW

Image

You can install Cisco Elastic Services Controller (ESC) on OpenStack by using a QCOW image. ESC will be deployed in the OpenStack as running VM instance to manage VNFs. Therefore, ESC need OpenStack environment parameters to be installed in OpenStack. The installation time varies from 10 to 20 minutes, depending on the host and the storage area network load. This procedure describes how to create ESC Virtual

Machine (VM) in OpenStack.

Before you begin

• All system requirements are met as specified in

Prerequisites, on page 5

• You have the information identified in

Preparing for the Installation, on page 6 .

• Copy the ESC image file on the system where you want to install ESC.

• This system must be accessible by OpenStack.

Procedure

Step 1

Step 2

Check the compatibility of the bootvm.py and the ESC image:

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Installing Cisco Elastic Services Controller on OpenStack

Installing Cisco Elastic Services Controller Using the QCOW Image

Step 3

./bootvm.py --version

For more information on the ESC installer arguments, see Appendix: A Cisco Elastic Services Controller

Installer Arguments .

In a text editor, create a file named PROJECT-openrc.sh file and add the following authentication information.

The following example shows the information for a project called admin, where the OpenStack username is also admin, and the identity host is located at controller node.

Note To set the required environment variables for the OpenStack command-line clients, you must create an environment file called an OpenStack rc file, or openrc.sh file. This project-specific environment file contains the credentials that all OpenStack services use. The ESC installation script requires these OpenStack environment parameters to perform authentication and installation on OpenStack.

If all the OpenStack credentials are passed through its own arguments, the bootvm.py script doesn't require these parameters.

Step 4

Step 5

Step 6 export OS_NO_CACHE=true export OS_TENANT_NAME=admin export OS_USERNAME=admin export OS_PASSWORD=admin_pass export OS_AUTH_URL= http://controller node:35357/v2.0

The other OpenStack parameters required for installation are: --os_auth_url, --os_username, --os_password

, -os_tenant_name, --bs_os_user_domain_name, --bs_os_project_domain_name, --bs_os_identity_api_version,

--bs_os_auth_url, --bs_os_username, --bs_os_password , -bs_os_tenant_name, --bs_os_user_domain_name,

--bs_os_project_domain_name, --bs_os_identity_api_version.

For OpenStack V2 API, you need following items to be defined in your global environment variables:

--os_password, --os_auth_url, --os_username, --os_tenant_name.

For OpenStack V3 API, set --os_identity_api_version=3 . Other parameters required for OpenStack V3 API are: --os_user_domain_name, --os_project_domain_name, --os_project_name, --os_password, --os_auth_url,

--os_username, --os_identity_api_version, --os_ca_cert, --requests_ ca_bundle.

Note The arguments, --os_tenant_name, --os_username, --os_password, --os_auth_url will also by default configure the VIM connector. If you want to skip configuring the VIM connector, pass the parameter

(--no_vim_credentials) with the bootvm.py. When no_vim_credentials parameter is provided, the bootvm.py arguments (os_tenant_name, os_username, os_password,os_auth_url) are ignored. For more information on configuring VIM connectors after installation, and managing VIM connectors, see Managing VIM Connectors in the Cisco Elastic Services Controller User Guide .

Note --os_ca_cert and --requests_ca_bundle arguments are only required for https connection.

On any shell from which you want to run OpenStack commands, source the PROJECT-openrc.sh

file for the respective project. In this example, you source the admin-openrc.sh

file for the admin project .

$ source admin-openrc.sh

Check the environment variables.

$ env | grep OS_

$ glance image-create \

--name <image_name> \

--is-public=<true or false> or --visibility public or private\

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Installing Cisco Elastic Services Controller on OpenStack

Installing Cisco Elastic Services Controller Using the QCOW Image

Step 7

Step 8

--disk-format <disk_format> \

--container-format <container_format> \

--file <file> \

--progress

An example configuration is shown below:

$ glance image-create \

--name esc-1_0_01_11_2011-01-01 \

--is-public=<true or false> or --visibility public or private \

--disk-format qcow2 \

--container-format bare \

--file esc-1_0_01_11_2011-01-01.qcow2 \

--progress

The glance image-create command is used to create a new image. The command takes the following arguments:

Note The 'is-public' argument is applicable only for OpenStack Kilo release.

Arguments name is-public disk-format container-format file progress

Description

Name of the image.

(Optional) Makes the image accessible to the public.

Disk format of the image. ESC uses a qcow2 disk format.

Container format of image. ESC uses a bare container format.

Local file that contains disk image to be uploaded during creation.

(Optional) Shows upload progress bar.

To verify whether the image has been registered successfully: a) Using OpenStack Controller dashboard:

• Log into OpenStack using your credentials.

• Navigate to Admin > Image .

Verify if the image appears in the list.

b) Using nova CLI:

$ nova image-show <image_name>

The standard resource requirement of ESC is 4vCPU, 8G RAM, and 40GB disk space. ESC installation script takes the pre-defined "m1.large" flavor which has the definition of 4vCPU, 8G RAM and 80G disk space. To use 40GB disk space, create a flavor with the minimum disk space requirement.

$ nova flavor-create ESC_FLAVOR_NAME ESC_FLAVOR_ID 8192 40 4

To deploy ESC VM, do the following: a.

Ensure that the existing network have connectivity to OpenStack controller. To verify the network connectivity using the nova CLI use:

$ nova net-list

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Installing Cisco Elastic Services Controller on OpenStack

Installing Cisco Elastic Services Controller Using the QCOW Image b.

Record the ID of the network that ESC connects to boot the ESC VM by with image and flavor created earlier. The bootvm.py command requires at least one --user_pass argument to create an admin account for linux (ssh/console access) and at least one --user_confd_pass to create an admin account for ConfD

(netconf/cli access). The following are the syntax for these mandatory user credential arguments:

--user_pass admin:'PASSWORD-OR-HASH'[:OPTIONAL-PUBLIC-KEY-FILE][:OPTIONAL-ROLE]

--user_confd_pass admin:'PASSWORD-OR-HASH'[:OPTIONAL-PUBLIC-KEY-FILE]

Generating hashed password is optional. You can select a plain password as and when required.

To generate a hashed password on Ubuntu OS, use the following command: mkpasswd --method=SHA-512 --salt XyZ123 <<< <Password>

Starting ESC Release 5.4, invoking the esc_nc_cli command without username and password fails with the following message: admin@esc$ esc_nc_cli --user <username> --password <password> get esc_datamodel/opdata/status

ERROR Cannot find file /home/admin/.ssh/confd_id_rsa to support public key authentication with esc-nc-admin

* Check your arguments or installation.

* Usage without --user --password or --privKeyFile arguments requires ssh keys and configuration.

* Use the following command to generate new SSH Keys and update to authorized_keys: sudo escadm confd keygen --user admin

* NOTE: Consult with site security policies for use of public key authentication.

You must run the esc_nc_cli command with a username and password: admin@esc$ esc_nc_cli --user admin --password ADMIN-CONFD-PASSWORD get esc_datamodel/opdata/status

Operational Data

/opt/cisco/esc/confd/bin/netconf-console --port=830 --host=127.0.0.1 --user admin

--password=****** --get -x "esc_datamodel/opdata/status"

<?xml version="1.0" encoding="UTF-8"?>

<rpc-reply xmlns="urn:ietf:params:xml:ns:netconf:base:1.0" message-id="1">

<data>

<esc_datamodel xmlns="http://www.cisco.com/esc/esc">

</opdata>

</esc_datamodel>

</data>

</rpc-reply>

The following is an example to install ESC with an authorized public key. In the following example, single quotes are used to avoid conflict with shell reserved characters:

--user_pass admin:'$algorithm$salt$hash-of-salt-password':$HOME/.ssh/esc_rsa.pub

--user_confd_pass admin:'$algorithm$salt$hash-of-salt-password':$HOME/.ssh/esc_rsa.pub

The public keys are generated as part of a key pair, such as: ssh-keygen -t rsa -b 1024 -C "esc" -N "" -f ~/.ssh/esc_rsa

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Installing Cisco Elastic Services Controller on OpenStack

Additional Installation Options

Your public key and identification key are saved in /home/username /.ssh/esc_rsa and esc_rsa.pub files.

For more examples on the user credential arguments, see Appendix A: Cisco Elastic Services Controller

Installer Arguments.

To check the details of ESC VM and get the information including the IP address(es) of the ESC VM, use the following command:

$ nova show <esc_vm_name>

Additional Installation Options

• Creating ConfD SSH Keys: Starting ESC Release 5.4, you can invoke the following command to create

SSH keys and configure the public key authentication: sudo escadm confd keygen --user USERNAME

Run the above command on each user account on the ESC VM that requires authentication without password. In an Active/Standby deployment, run the command on both the nodes.

Enabling ConfD SSH keys using bootvm.py: Enabling the following bootvm.py command restores the functionality prior to ESC Release 5.4:

--confd_keygen

For information on ConfD cli, see Changing the ConfD NetConf CLI Administrator Password Using the

Command Line Interface.

• Deploying ESC in an OpenStack IPv6 environment: Before deploying ESC instance in IPv6, make sure to source openrc that supports ipv6 addresses. To deploy ESC in IPv6 environment, use the following bootvm arguments:

./bootvm.py

<esc_vm_name-ipv6> --poll --user_rest_pass <username> : <password> --image

<image_name>

--net <ipv6_network> --ipaddr <ipv6_ip_address> --enable-http-rest --user_pass

<username> : <password>

--user_confd_pass <username> : <password> --etc_hosts_file <hosts-file-name> --route

<default routing configuration>

• Deploying ESC in DHCP mode: If you use the bootvm.py argument without --ipaddr, then the ESC instance will be deployed in a DHCP mode. To deploy ESC in a DHCP network, use the following configuration:

./bootvm.py

<esc_vm_name> --image <image_name> --net <IPv6 network> <IPv4 network>

--flavor <flavor_name>

--user_pass <username> : <password>

--user_confd_pass <username> : <password>

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Installing Cisco Elastic Services Controller on OpenStack

Additional Installation Options

Note By default, ESC only support DHCP in IPv4 networks. If IPv6 is used, you need to log in the ESC VM and run "dhclient -6 ethX" (ethX is the V6 interface name) manually to enable V6 DHCP.

When deploying ESC with multiple network interfaces, with one or more type of DHCP, use bootvm.py --defroute N to specify the interface index to be assigned default route and gateway IP.

By default,

N = 0

. So the first network interface on the bootvm.py

command line is default.

For Example:

--defroute 1 will assign <network2> with <default_gateway_ip_address>

./bootvm.py <esc_vm_name> --image <image_id> --net <network1>

<network2> --defroute 1 --gateway_ip <default_gateway_ip_address>

• Using a Bootable Volume in ESC Installation: You can attach a volume to an ESC instance and launch

an instance from inside the volume. For more information, see the section Using a Bootable Volume in

ESC Installation

• Assigning Floating IP to the ESC: If you want to associate a floating IP with the ESC instance , do the following:

Check for an available floating IP address and assign it to the ESC VM:

$ nova floating-ip-list

$ nova floating-ip-associate esc_vm_name <ip_address>

Or create a new floating IP address and assign it to the ESC VM:

$ nova floating-ip-create <FLOATING_NETWORK - ID>

$ nova floating-ip-associate esc_vm_name <ip_address> or neutron floatingip-create FLOATING_NETWORK neutron floatingip-associate floating-ip-ID port-ID

• Deploying ESC with static IPs: To use ESC in a specific network with static IPs, for example,

192.168.0.112 at network1, specify --ipaddr and --gateway_ip to the bootvm command line , as shown below:

Note Before assigning static IP, make sure the static IP is available and is not being used on other machine.

./bootvm.py

<esc_vm_name> --image <image_id> --net <network>

--ipaddr <ip_address> --gateway_ip <default_gateway_ip_address> --user_pass

<username> : <password>

--user_confd_pass <username> : <password>

• Deploying ESC with multiple network interfaces: To use multiple networks for ESC, for example,

192.168.0.112 at network1 and 10.20.0.112 at network2, specify both the IP addresses and the network names of the interfaces in the --net and --ipaddr arguments in the following command line. In addition,

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Installing Cisco Elastic Services Controller on OpenStack

Additional Installation Options also choose the default gateway for ESC from the gateways of these networks. Specify the default gateway for ESC through the --gateway_ip argument.

./bootvm.py

<esc_vm_name> --image <image_id> --net <network1>

<network2> --ipaddr <ip_address1> <ip_address2> --gateway_ip <default_gateway_ip_address>

--user_pass <username> : <password>

--user_confd_pass <username> : <password>

Note If --flavor is not specified, bootvm.py will use the default flavor "m1.large" in

OpenStack.

Ensure that m1.large exist in OpenStack if decide not specified a flavor, and also ensure that the flavor suits ESC deployment requirement.

• Deploy ESC with log forwarding options: To forward ESC logs to an rsyslog server, specify the IP address of the rsyslog server while creating an ESC VM. Optionally, you can also specify the port and protocol to use.

For example, if the IP address of the rsyslog server is 172.16.0.0 the port on the server to forward logs is 514, and the protocol used is UDP, the ESC installation could be

./bootvm.py

<esc_vm_name> --image <image_id> --net network1 --rsyslog_server 172.16.0.0

--rsyslog_server_port 514 --rsyslog_server_protocol udp --user_pass <username> : <password>

--user_confd_pass <username> : <password>

• Disabling the ESC GUI: To boot up ESC VM with the graphical user interface disabled, modify the

--esc_ui_startup argument value, as shown in the command line below:

./bootvm.py

<esc_vm_name> --image <image_id> --net <network> --user_pass

<username> : <password>

--user_confd_pass <username> : <password>

--esc_portal_startup=False

• Enabling REST interface for ESC: To support the REST interface, specify --enable-https-rest argument.

You can activate REST interface on both https or http:

./bootvm.py

<esc_vm_name> --image <image_id> --net <network> --user_pass

<username> : <password>

--user_confd_pass <username> : <password> --enable-https-rest

./bootvm.py

<esc_vm_name> --image <image_id> --net <network> --user_pass

<username> : <password>

--user_confd_pass <username> : <password> --enable-http-rest

•

• Enabling REST interface for ETSI: To support the ETSI REST intetrface, specify --enable-http-etsi to activate the interface over http, or --enable-https-etsi to activate the interface over https.

./bootvm.py

<esc_vm_name> --image <image_id> --net <network> --user_etsi_pass

<username> : <password> --enable-https-etsi . . .

./bootvm.py

<esc_vm_name> --image <image_id> --net <network> --user_etsi_pass

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Installing Cisco Elastic Services Controller on OpenStack

Additional Installation Options

<username> : <password>

--user_confd_pass <username> : <password> --enable-http-etsi...

Note Only the https REST and ETSI interfaces should be enabled in a production environment.

• Deploying ESC with ETSI OAuth2 Clients: To add ETSI OAuth2 clients during the installation, use the arguments as shown below. The OAuth2 clients can also be added using the escadm commands after the installation.

./bootvm.py <esc_vm_name> --image <image_id> --net <network> -user_etsi_pass <username>:<password> --etsi_oauth2_pass <clientId>:<clientSecret>

--enable-https-etsi ...

• Deploying ESC with global parameters: To set the global configurations through the esc_params_file during the installation, use the arguments as shown below. These global configurations can also be changed through REST API after the installation.

Note The default security group is applied to the tenant during tenant creation. By default, the ESC configuration parameter for the security group, openstack.DEFAULT_SECURITY_GROUP_TO_TENANT

is set to true. The configuration parameter must be set at the time of installation. You can query or update the parameter on ESC VM through the REST API. If the parameter is set to true, you can create and assign default security group during tenant creation.

If the parameter is set to false, you cannot create or assign default security group during tenant creation. For details on the parameters that can be configured through esc_params_file, see Appendix A: Cisco Elastic Services Controller Installer

Arguments.

./bootvm.py <esc_vm_name> --image <image_id> --net <network> --flavor <flavor_name>

--user_pass <username>:<password>:<public key file> --user_confd_pass

<username> : <password>

--esc_params_file <esc parameter configuration file>

• Deploying ESC with ETSI properties : To set the ETSI properties through the etsi_params_file during installation, use the arguments as shown below. These properties can also be changed in the etsi-production.properties

file after the installation.

Note For details on the properties that can be configured through the etsi_params_file, see the ETSI Production Properties chapter in the ETSI NFV MANO User Guide .

./bootvm.py <esc_vm_name> --image <image_id> --net <network> --flavor <flavor_name>

--user_pass <username>:<password>:<public key file> --user_confd_pass

--etsi_params_file <etsi properties file>

• Deploying two instances of ESC to build an ESC HA (Active/Standby) pair : For more information on deploying ESC HA (Active/Standby), see Configuring High Availability in Installing ESC on

OpenStack and Installing ESC on VMware chapters.

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Installing Cisco Elastic Services Controller on OpenStack

Managing Root Certificates in Cisco Elastic Services Controller

• Adding a Dynamic Mapping File : In Cisco ESC Release 2.1 and earlier, mapping the actions and metrics defined in the datamodel to the valid actions and metrics available in the monitoring agent was enabled using the dynamic_mappings.xml

file. The file was stored in the ESC VM and was modified using a text editor. ESC 2.2 and later do not have an esc-dynamic-mapping directory and dynamic_mappings.xml

file. If you want to add an existing dynamic_mapping xml file to the ESC VM, do the following:

Backup this file to a location outside of ESC, such as, your home directory.

Create esc-dynamic-mapping directory on your ESC VM. Ensure that the read permissions are set.

Install on your ESC VM using the following bootvm argument:

--file root:root: /opt/cisco/esc/esc-dynamic-mapping/dynamic_mappings.xml

:< path-to-local-copy-of-dynamic-mapping.xml

The CRUD operations for mapping the actions and the metrics is available through REST API. To update an existing mapping, delete and add a new mapping through the REST API.

• Changing the confd password on an ESC VM : As an administrator, you can configure the confd password through bootvm.py, during the installation time:

./bootvm.py --user_pass <username> : <password> --user_confd_pass admin:'PASSWORD-OR-HASH':OPTIONAL-PUBLIC-KEY

To reconfigure this password after the installation, execute the following commands:

$ /opt/cisco/esc/confd/bin/ssh admin@localhost -p 2024

$ configure

$ set aaa authentication users user admin password <your_password>

$ commit

$ exit

Note For the ease of future upgrades, make sure that you keep a copy of all the commands and arguments that are used while installing ESC using the bootvm.py file.

Managing Root Certificates in Cisco Elastic Services Controller

Cisco Elastic Services Controller (ESC) provides a mechanism to enable verification of SSL certificates.

Currently, this feature is supported only on OpenStack. Certificate validation is enabled by default during the initial ESC boot up. However, ESC also allows you to configure these SSL certificates. This section describes how to enable/disable certificate validation, add/remove, or list the certificates for Cisco Elastic Service

Controller on OpenStack. You can add a root certificate during the ESC bootup or even after ESC bootup is completed.

Enabling/Disabling the Root Certificate Validation

Cisco Elastic Services Controller by default enables certificate validation. You can also enable or disable by modifying the parameter, DISABLE_CERT_VALIDATION, available under the Openstack category in the esc_params.conf file, or through the REST interface, or using the escadm tool.

On ESC active node, use the command, sudo escadm enable-certificate or sudo escadm disable-certificate to enable and disable the certificate validation, respectively.

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Installing Cisco Elastic Services Controller on OpenStack

Adding a Root Certificate

Adding a Root Certificate

You can add a root certificate during the ESC bootup or even after ESC bootup is completed. Before adding certificates, ensure the OpenStack environment file, OpenStack RC file has parameters to perform authentication and installation on OpenStack. The --os_auth_url must be specified while passing the parameters. --os_auth_url specifies the secure (https) or unsecured (http) keystone URL used by OpenStack for authentication.

• Add certificate for standalone (only) during the bootup time, i.e, during the ESC VM installation:

./bootvm.py test-vm --image <image_name> --net <network> [--cert_file CERT_FILE]

[--confd_aes_key CONFD_AES_KEY]

/home/cisco/openstack.crt

--user_pass <username>:<password> --user_confd_pass <username>:<password>

Note Currently, ESC does not support adding a certificate for HA Active/Standby during the installation as the keepalived service is not running when a certificate is added.

• Add certificate for standalone/HA Active/Standby after booting up the ESC instance. The escadm tool has an truststore add option which has the following arguments: The --file argument refers to the CA certificate file. Using this argument you can import any file format supported by the java keytool: X.509

v1, v2, and v3 certificates, and PKCS#7. The --alias argument is unique and refers to the name this specific CA certificate is given.

Copy/Transfer CA Certificate file to ESC active VM .

Add certificate to ESC truststore. To do this, execute the following command: sudo escadm escadm truststore add --alias [ca cert alias] --file [file path] or sudo escadm truststore escadm truststore --alias [ca cert alias] --file [file path]

Verify the certificate is added.

sudo escadm truststore show or sudo escadm truststore show

Removing a Root Certificate

The escadm tool has a 'truststore delete' option which only takes --alias argument. The --alias argument refers to the name of the CA certificate to be deleted. Use this argument on the standalone/HA Active/Standby ESC

VM:

Procedure

Step 1 On (active)ESC use escadm to delete certificate from ESC truststore.

sudo escadm truststore delete --alias [ca cert alias]

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Installing Cisco Elastic Services Controller on OpenStack

Managing Root Certificates During the Upgrade

Step 2 or sudo escadm truststore truststore delete --alias [ca cert alias]

Verify the certificate is removed.

sudo escadm truststore show or sudo escadm truststore show

Managing Root Certificates During the Upgrade

• Image Upgrade : If you are backing up the ESC DB for upgrade, then no other action is required, the

ESC truststore will be restored once the ESC DB is restored. If you are not backing up the ESC DB for upgrade, then each CA certificate needs to be added again to the ESC truststore.

• RPM Upgrade : This upgrade method keeps the ESC truststore as is, i.e. all ca certificates in the ESC truststore should remain there after upgrade.

Managing Keystore in Cisco Elastic Services Controller

The keystore is a storage for certificates and keys that an application uses to authenticate itself with different clients.

ESC Keystore holds only one certificate, that is used by all the applications for example, ESCManager,

VIMManager, MONA, and so on.

ESCADM provides multiple commands to manage the keystore.

When deploying ESC for the first time, a self signed certificate is created and stored in the keystore by default.

important Notes:

• In an Active/Active mode, the default certificate Common Name (CN) is db.service.consul

. If you want to set a new certificate, you must set it with the same CN, otherwise, you must add the following configuration to the heat template of all the nodes to disable the certificate validation in MONA when deploying the ESC: mona: certificate_validation: false

• All the escadm keystore commands require root privileges to be executed on the ESC.

ESCADM Keystore Commands

• escadm keystore show

The escadm keystore show command displays information about the certificate currently stored in the keystore. It shows informations like, the creation date, Alias, and certificate fingerprint.

For example:

$ sudo escadm keystore show

Keystore type: PKCS12

Keystore provider: SUN

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Installing Cisco Elastic Services Controller on OpenStack

ESCADM Keystore Commands

Your keystore contains 1 entry esc, Apr 13, 2020, PrivateKeyEntry,

Certificate fingerprint (SHA1):

FF:11:66:3E:93:DD:3A:0B:9A:72:40:16:35:34:D2:22:E1:25:07:80

• escadm keystore export [--out <file path>]

The export command displays the full content of the certificate. If the out option is specified, the content is saved in a file whose path is specified in the previous option.

• escadm keystore set-- file <file path>

The set command replaces the current certificate with a new one residing inside the file whose path is specified in the option file

Ensure that the file is in PEM format, containing both the certificate and a private key.

The following example shows how to generate a new self-signed certificate and set it to the keystore:

Use the following command to generate the certificate: openssl req -newkey rsa:2048 -new -nodes -x509 -days 3650 -keyout key.pem -out cert.pem

The previous commands gives the following two files: key.pem

and cert.pem

Use the following commands to combine the two files: cat key.pem > server.pem

cat cert.pem >> server.pem

To set the new certificate to the keystore, use the following command:

$ sudo escadm keystore set --file server.pem

Service "keystore" successfully updated ESC keystore and will take effect once ESC services are restarted by running "sudo escadm restart"

Note Ensure that you delete any left over files containing private keys and certificate after the setting is done.

It is mandatory to restart your system for the change to take effect. Use the following command to restart in standalone mode or H/A mode: sudo escadm restart

If the ESC is running in the Active/Active mode, you must restart all the nodes in the same cluster.

However, if the ESC is running in an Active/Active GEO mode, you must stop the GEO service on all the clusters, to make sure a GEO switchover does not take place.

Only in GEO Active/Active mode, to stop GEO service, log in to any node in each cluster and use the following command:

$ sudo escadm geo stop --cluster

You can login to any node in the cluster where the certificate is originally set. Use the following command:

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Installing Cisco Elastic Services Controller on OpenStack

Using a Bootable Volume in ESC Installation

$ sudo escadm stop --cluster

$ sudo escadm start --cluster

If you are on a GEO Active/Active mode, once all the node are up and running in passing state, login again to any node to start the GEO service. Use the folowing command to start the service:

$ sudo escadm geo start --cluster

Using a Bootable Volume in ESC Installation

A volume in OpenStack is a detachable block storage device that can be attached to an ESC instance. You can store and also run ESC instances from a volume.

Note • Only one ESC instance can be launched from one volume at a time.

• ESC installation with a combination of bootable volume and high availability (Active/Standby and

Active/Active) on cinder is not supported.

To launch an ESC instance from a bootable volume, do the following:

Procedure

Step 1

Step 2

Create a bootable volume in OpenStack based on an ESC image or from a bootable volume. The bootable volume must be at least of 30 GB disk size. For more information, see OpenStack documentation.

Deploy ESC VM using the bootvm.py

command and choose the

--boot_volume argument instead of the

--image argument, as shown below:

./bootvm.py <esc_vm_name> --boot_volume <volume_name_or_id> --net <network> --user_pass

--user_confd_pass <username>:<password> --flavor <flavor_name>

Note • Only one of these arguments,

--image or

--boot_volume must be passed to the bootvm.py

command. The installation will fail, if both or none of the arguments are used.

• When launching an ESC instance from a bootable volume, volume disk size is considered over the flavor disk size.

• If an ESC instance is deleted, the volume attached to it will not be deleted, as the volume was created out-of-band.

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

C H A P T E R

Installing High Availability Active/Standby

This chapter contains the following sections:

•

High Availability Active/Standby Overview, on page 21

•

How High Availability Works, on page 22

•

Deploying ESC High Availability Active/Standby, on page 23

•

Configuring the Northbound Interface Access, on page 26

•

Important Notes, on page 31

•

Troubleshooting High Availability Active/Standby, on page 32

High Availability Active/Standby Overview

ESC supports High Availability (HA) in the form of Active/Standby and Active/Active models. For

Active/Standby model, two ESC instances are deployed in the network to prevent ESC failure and provide

ESC service with minimum service interruption. If the active ESC instance fails, the standby instance automatically takes over the ESC services. ESC HA Active/Standby resolves the following single point failures:

• Network failures

• Power failures

• Dead VM instance

• Scheduled downtime

• Hardware issues

• Internal application failures

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

ESC Active/Standby Architecture

ESC Active/Standby Architecture

Figure 1: Cisco Elastic Services Controller Active/Standby Architecture

Installing Cisco Elastic Services Controller on OpenStack

How High Availability Works

ESC HA Active/Standby network can be either set up as a single installation of a ESC HA Active/Standby pair or deployed as two standalone ESC nodes that are converted into HA pair after re-configuring these nodes post deployment. The HA deployment consists of two ESC instances: an active and a standby. Under normal circumstances, the active ESC instance provides the service. The corresponding standby instance is passive.

The standby instance is in constant communication with the active instance and monitors the active instances' status. If the active ESC instance fails, the standby instance automatically takes over the ESC services to provide ESC service with minimum interruption.

The standby also has a complete copy of the database of the active, but it does not actively manage the network until the active instance fails. The KeepAliveD service monitors both active and standby instances activity status. When the active instance fails, the standby takes over automatically. The standby instance takes over active instance to manage the services while active instance restoration is taking place.

When the failed instance is restored, if required you can manually initiate a switch-over and resume network management via the active instance.

Both active and standby ESC instances are connected to the northbound orchestration system through an IPv4 or IPv6 network. For the northbound system, a unique virtual IP address is assigned to access the current active ESC High Availability Active/Standby instance. The deployed VNFs are connected to both ESC active and standby instances through another IPv6 network.

ESC HA Active/Standby nodes are managed by KeepAliveD and DRBD (Replication tool to keep the ESC database synchronized) sync network services. While the KeepAliveD service monitors both active and standby instances status, the DRBD service monitors active instance DB and sync the changes to the standby instance

DB. These two services can be co-located on same VIP network or in two separate networks. VM handshake between ESC instances occurs through the KeepAliveD over the IPv4 or IPv6 network.

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Installing Cisco Elastic Services Controller on OpenStack

Deploying ESC High Availability Active/Standby

Deploying ESC High Availability Active/Standby

To deploy Cisco Elastic Services Controller (ESC) High Availability (HA) Active/Standby, ESC standalone instances can be installed on two separate nodes - Active and Standby. For more information see,

How High

Availability Works, on page 22

. You can connect the active and standby instances to either a Cinder volume or Replication based volume (DRBD).

The following deployment mechanisms can be used to deploy ESC HA Active/Standby:

• Internal Storage—When ESC HA Active/Standby is configured with Internal storage, the active and the standby instances have individual databases which are always synchronized. In this solution, ESC HA

Active/Standby is designed with database replication and DRBD is used as the tool for disk-level replication. The database in the active instance simultaneously propagates the data to the database in the standby instance thus requiring no external storage. In the event of an active instance failing, the standby instance get assigned the role of the active instance along with its own synchronized database.

ESC HA Active/Standby is deployed using internal storage, the ESC instances reply on the virtual IP address (that is kad_vip argument), and the interface of vrrp instance (that is kad_vif argument) to select the active ESC instance. To establish a reliable heartbeat network, it is recommended that the active and standby ESC instances are on different physical hosts. The reliability of the physical links between the

ESC instances (such as, network interface bonding) can also be taken into consideration.

• Replicate External-Storages — In this type of architecture, ESC HA Active/Standby is configured with

DRBD and both active and standby instances store their data in two external storages (OpenStack Cinder volumes). Each ESC node is attached by a Cinder volume and ESC data files are stored in the cinder volume. The data in two ESC nodes are synchronized through the database replication mechanism provided by DRBD.

The table lists the differences between the HA Active/Standby options :

Data sharing method

Installation Method

Internal Storage Based ESC HA

Active/Standby

Replicate External Storage Based ESC HA

Active/Standby

Data replication between HA

Active/Standby nodes

Post-installation Configuration

Bootvm Installation

Data replication between two external storages (cinder volume)

Bootvm Installation

VIM Support

Dependency

Advantages

OpenStack, VMware, KVM

VIM independent

• No dependency on specific

VIM components.

• Flexible to build of HA

Active/Standby clusters from commodity hardware, without the requirement for shared-storage.

OpenStack only

Rely on OpenStack cinder

• Use database replication mechanism for data synchronization

• Two cinder volumes are used as external storage and are attached to ESC node.

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Installing Cisco Elastic Services Controller on OpenStack

Deploying ESC in High Availability Active/Standby Mode on Internal Storage

Limitations The data consistency may be affected in a double fault condition

(occurs when both ESC nodes have problems).

The data consistency may be affected in a double fault condition (occurs when both

ESC nodes have problems).

Deploying ESC in High Availability Active/Standby Mode on Internal Storage

When you boot ESC instances on active and standby instances, you need to specify the following bootvm.py

command arguments to deploy ESC HA Active/Standby on an internal storage:

• kad_vip

Note When ESC HA Active/Standby is deployed, the kad_vip argument allows end users to access the active ESC instance.

• kad_vif

• ha_node_list

These arguments enable the bootvm.py

command to automatically set up the internal storage on the OpenStack.

For more information on using the bootvm.py

command arguments, see Appendix A: Cisco Elastic Services

Controller Installer Arguments.

To deploy ESC HA Active/Standby instances, use the bootvm script on both the nodes with the following arguments:

ON HA NODE 1:

$ ./bootvm.py <ESC_HA_Node1>\

--user_pass <username>:<password>\

--user_confd_pass <username>:<password>\

--gateway_ip <default gateway IP address>\

--net <network name1>\

--ipaddr <static ip address>

--image <image_name>\

--avail_zone nova:<openstack zone>\

--ha_node_list=<ESC_HA_NODE1_IP> <ESC_HA_NODE2_IP>\

--db_volume_id <cinder volume id>\

--kad_vip <virtual IP address>\

--kad_vif <VRRP_Interface_Instance>\

--ha_mode drbd

ON HA NODE 2:

$ ./bootvm.py <ESC_HA_Node2>\

--user_pass <username>:<password>\

--user_confd_pass <username>:<password>\

--gateway_ip <default gateway IP address>\

--net <network name1>\

--ipaddr <static ip addresses>\

--image <image_name>\

--avail_zone nova:<openstack zone>\

--ha_node_list=<ESC_HA_NODE1_IP> <ESC_HA_NODE2_IP>\

--db_volume_id <cinder volume id>\

--kad_vip <virtual IP address>\

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Installing Cisco Elastic Services Controller on OpenStack

Deploying ESC in High Availability Active/Standby Mode on Replicate External Storage

--kad_vif <VRRP_Interface_Instance>\

--ha_mode drbd

You can also use escadm tool to re-configure ESC HA Active/Standby parameters on each of the standalone

ESC VMs. Three parameters "--ha_node_list , --kad_vip, --kad_vif" are all required to configure ESC HA

Active/Standby.

Note You should make sure that both the standalone ESC VMs health check is passed before running the below commands to perform HA Active/Standby configuration.

For example:

$ sudo bash

$ escadm ha set --ha_node_list='<ESC_HA_NODE1_IP> <ESC_HA_NODE2_IP>' --kad_vip <virtual IP address> --kad_vif <VRRP_Interface_Instance>

$ sudo escadm reload

$ sudo escadm restart

Deploying ESC in High Availability Active/Standby Mode on Replicate External Storage

Replicate external storage ESC HA Active/Standby requires two cinder volumes for database storage.

Before you begin

• Networks and IP addresses that both ESC instances will connect to

• Keepalived interface and virtual IP for HA Active/Standby switchover

Procedure

Step 1

Step 2

Step 3

Create two cinder volumes in OpenStack. The configured cinder volume size should be 3GB.

$ cinder create --display-name cindervolume_name_a[SIZE]

$ cinder create --display-name cindervolume_name_b[SIZE]

Check the status of the created cinder volume and find the uuids for deployment.

$ cinder list

Deploy ESC HA Active/Standby instances. Use the bootvm script on both the nodes with the following arguments:

ON HA NODE 1:

$ ./bootvm.py <ESC_HA_Node1>\

--user_pass <username>:<password>\

--user_confd_pass <username>:<password>\

--gateway_ip <default gateway IP address>\

--net <network name1>\

--ipaddr <static ip address>\

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Installing Cisco Elastic Services Controller on OpenStack

Configuring the Northbound Interface Access

Step 4

--image <image_name>\

--avail_zone nova:<openstack zone>\

--kad_vip <virtual IP address>\

--kad_vif <VRRP_Interface_Instance>\

--ha_node_list=<ESC_HA_NODE1_IP> <ESC_HA_NODE2_IP>\

--db_volume_id <cinder volume id>\

--ha_mode drbd_on_cinder

ON HA NODE 2:

$ ./bootvm.py <ESC_HA_Node2>\

--user_pass <username>:<password>\

--user_confd_pass <username>:<password>\

--gateway_ip <default gateway IP address>\

--net <network name1>\

--ipaddr <static ip address>\

--image <image_name>\

--avail_zone nova:<openstack zone>\

--kad_vip <virtual IP address>\

--kad_vif <VRRP_Interface_Instance>\

--ha_node_list=<ESC_HA_NODE1_IP> <ESC_HA_NODE2_IP>\

--db_volume_id <cinder volume id>\

--ha_mode drbd_on_cinder

After both VMs are rebooted; one of ESC VM should be in ACTIVE state and the other one should be in

STANDBY state. You can check ESC HA Active/Standby state by using following command: $ sudo escadm status --v .

Configuring the Northbound Interface Access

When you configure ESC HA Active/Standby, you can also specify a virtual Anycast IP address to the HA

Active/Standby pair. The northbound interface as well as the service portal uses virtual Anycast IP address to access the ESC active HA Active/Standby instance. When deploying ESC HA Active/Standby, use the following arguments with the ./bootvm.py

script.

• --ha_node_list

• --kad_vip

• --kad_vif

For more details on these arguments, see section Appendix A: Cisco Elastic Services Controller Installer

Arguments .

The following section explains how to configure ESC HA Active/Standby with multiple interfaces and to configure the virtual Anycast IP address.

Configuring ESC HA Active/Standby with Multiple Interfaces

You can configure ESC HA Active/Standby with DRDB synchronization and VRRP heartbeat broadcasting on a network interface for data synchronization and VNF monitoring. You can use an additional network interface to allocate Virtual IP for the northbound access. To configure the multiple interfaces on ESC HA

Active/Standby nodes, use --ha_node_list, --kad_vip, --kad_vif arguments to specify these multiple network interfaces configuration. For details on these arguments, see section Appendix A: Cisco Elastic Services

Controller Installer Arguments .

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Installing Cisco Elastic Services Controller on OpenStack

Configuring the ESC HA Active/Standby Virtual IP Address

Note KeepAlived doesn’t support single IPv4 VIP address with a IPv6 VRRP instance.

Example configuration steps are shown below:

./bootvm.py <esc_ha1> \

--user_pass <username>:<password>

--user_confd_pass <username>:<password>

--image <image_id> \

--net <net-name> \

--gateway_ip <default_gateway_ip_address> \

--ipaddr <ip_address1> <ip_address2> \

--ha_node_list < IP addresses HA nodes1> < IP addresses for HA nodes2> \

--kad_vip <keepaliveD VIP of the HA nodes and the interface for keepaliveD VIP> \ (for example: --kad_vip 192.0.2.254:eth2)

--kad_vri <virtual router id of vrrp instance>

--kad_vif <virtual IP of the HA nodes or the interface of the keepalived VRRP> \ (for example: --kad_vif eth1 )

--ha_mode <HA installation mode> \

--route <routing configuration> \ (for example:192.0.2.254/24:192.168.0.1:eth1 )

--avail_zone nova:<openstack zone> \

Similarly, a three network interface can be configured for ESC HA Active/Standby nodes. An example three interfaces configuration is shown below with the following assumptions :

• Network 1 is an IPv6 network used for northbound connection. ESC VIP is allocated in this network and the Orchestrator send requests to ESC through ESC VIP.

• Network 2 is an IPv4 network used for ESC sync traffic (DRDB synchronization) and VRRP heartbeat.

This network is also used for OpenStack connection and VNF monitoring.

• Network 3 is another IPv4 network used for management. The SA, rsyslog, etc. can use this network to manage ESC.

./bootvm.py esc-ha-0 --image ESC-2_2_x_yyy --net network-v6 network --gateway_ip 192.168.0.1 --ipaddr

2001:cc0:2020::fa 192.168.0.239 192.168.5.239 --ha_node_list 192.168.0.239 192.168.0.243 --kad_vip

[2001:cc0:2020::fc/48]:eth0 --kad_vif eth1 --ha_mode drbd --route 172.16.0.0:eth1 --avail_zone nova: zone name

./bootvm.py esc-ha-1 --image ESC-2_2_x_yyy --net network-v6 network lab-net-0 --gateway_ip 192.168.0.1

--ipaddr 2001:cc0:2020::fa 192.168.0.239 192.168.5.239 --ha_node_list 192.168.0.239 192.168.0.243 --kad_vip

[2001:cc0:2020::fc/48]:eth0 --kad_vif eth1 --ha_mode drbd --route 172.16.0.0:eth1 --avail_zone nova: zone name

Configuring the ESC HA Active/Standby Virtual IP Address

In this option, the value of kad_vip argument should be a virtual IP, which allows the service portal and the northbound to access the active ESC and send requests to ESC HA Active/Standby service through virtual IP

(VIP).

If northbound and both ESC HA Active/Standby nodes are located in the same network, you can connect directly through the virtual IP (VIP). If northbound doesn't sit on the same network as ESC HA Active/Standby, assign a floating IP to ESC HA Active/Standby VIP using the procedure below:

Create a port with the VIP address (kad_vip) in the same network as ESC's kad_vip connects.

neutron port-create network --name network_vip --fixed-ip subnet_id=network-subnet,ip_address=192.168.0.87

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Installing Cisco Elastic Services Controller on OpenStack

Configuring the ESC L3 HA Active/Standby With BGP

Deploy ESC HA Active/Standby . See Configuring High-Availability Active/Standby section in Installing

ESC on OpenStack.

Note Make sure the kad_vip using the same IP address as the port created above.

Associate a floating IP with the port created above. The first uuid is the floating ip id and the second one is the port id.

neutron floatingip-associate <floating IP> <port ID>

Access ESC HA Active/Standby through the floating IP and it will connect to the ESC active node.

For the portal access, make sure the keepalive network is accessible by your browser and the virtual IP is the IP address to access the portal of the active node.

For example, if the VIP is 192.0.2.254, access ESC HA Active/Standby portal with https://192.0.2.254:9001/.

Configuring the ESC L3 HA Active/Standby With BGP

To configure BGP for ESC HA Active/Standby, there are two options:

Directly booting ESC HA Active/Standby L3 with BGP

Using post configuration from existing ESC HA Active/Standby pair

To configure BGP for ESC HA Active/Standby, the following network parameters are required:

• BGP remote IP

• IP of the interface for BGP anycast routing

• BGP local AS number for routing configuration

• BGP remote AS number for routing configuration

• BGP routing configuration

• --bgp_local_ip

• --bgp_local_router_id

Note You must configure BGP router with neighbors, and restart it. Verify that the router is able to ping the AnyCast

IP.

On the BGP router, set two neighbors. The below BGP configuration is designed for Bird router. The configuration is router specific. For each types of router, the procedure is different:

The below configurations are given according to the bootvm command : protocol bgp E3 from EXABGP { neighbor 198.18.42.222 as 65012;

}

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Installing Cisco Elastic Services Controller on OpenStack

Configuring the ESC L3 HA Active/Standby With BGP protocol bgp E4 from EXABGP { neighbor 198.18.61.222 as 65011;

}

Booting an ESC VM with BGP options

[admin@na-test-52-1 ~]$ health.sh

============== ESC HA (ACTIVE) with DRBD ================= vimmanager (pgid 41908) is running monitor (pgid 42067) is running mona (pgid 42130) is running drbd (pgid 38488) is active snmp (pgid 2121) is running etsi (pgid 43247) is running pgsql (pgid 42566) is running keepalived (pgid 40281) is running portal (pgid 43307) is running confd (pgid 25644) is running filesystem (pgid 0) is running escmanager (pgid 42775) is running

=======================================

ESC HEALTH PASSED

[admin@na-test-52-2 ~]$ health.sh

============== ESC HA (Standby) with DRBD ================= pgsql is stopped vimmanager is stopped monitor is stopped mona is stopped drbd (pgid 2471) is standby etsi is disabled at startup filesystem is stopped snmp is disabled at startup bgp is stopped keepalived (pgid 2787) is running portal is stopped confd is stopped escmanager is stopped

=======================================

ESC HEALTH PASSED

Use below values for BGP post configuration:

./bootvm.sh <NETWORK_VM_name> \

--image <ESC_image> \

--ipaddr <static_IP_address1> <IP_address2> <IP_address_3>\

--gateway_ip <gateway IP address of NETWORK> \

--net <net_id1> <net_id2> <net_id3> \

--network_params_file <network_params_file> \

--host_mapping_file <host_mapping_file> \

--avail_zone <openStack_zone> \

--ha_node_list <IP_address_ha_node_1> <IP_address_ha_node_2> \

--user_portal_pass <user>:<password> \

--user_rest_pass <user>:<password> \

--confd_aes_key <password> \

--kad_vif <interface> \

--user_confd_pass <user>:<password> \

--user_pass <user>:<password> \

--kad_vip <vip address> \

--bgp_remote_ip <BGP_remote_IP_address> \

--bgp_local_ip <BGP_local_IP_address> \

--bgp_local_as <BGP_local_AS_#> \

--bgp_remote_as <BGP_remote_AS_#>\

--bgp_local_router_id <local_BGP_reouter_id> \

--bgp_anycast_ip <BGP_anycast_IP> \

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Installing Cisco Elastic Services Controller on OpenStack

Configuring the ESC L3 HA Active/Standby With BGP

--bgp_md5 <BGP_MD5>

Where,

--ip_addr: ----> the local IP address of the ESC VM

--net: ----> the network id(s) in OpenStack that ESC will connect to.

--bgp_anycast_ip: ----> the IP address that NCS will communicate with

--bgp_remote_ip: ----> this IP address of the external router that ESC will peer with

--bgp_local_as: ----> local AS for the ESC "router"

--bgp_remote_as: ----> AS number for the external router ESC will peer with

--bgp_local_router_id: ----> id for the esc "router"

--bgp_md5: ----> optional - md5 to be used to pair with external router

Configuring BGP HA Active/Standby Post Configuration

For each HA Active/Standby instance, create the network interface file:

# cat /etc/sysconfig/network-scripts/ifcfg-lo:2

IPV6INIT='no'

IPADDR='10.0.124.124'

BROADCAST='10.0.124.255'

<------------------ bgp anycast IP

NETWORK='10.0.124.0'

NETMASK='255.255.255.0'

DEVICE='lo:2'

ONBOOT='yes'

NAME='loopback'

For each HA Active/Standby instance:

Bring lo:2 up

# ifup lo:2

To configure BGP for ESC HA Active/Standby, use the escadm tool in ESC Virtual Machine, as shown below:

$ sudo bash

# escadm bgp set --local_ip LOCAL_IP --anycast_ip ANYCAST_IP --remote_ip REMOTE_IP --local_as

LOCAL_AS --remote_as REMOTE_AS

--local_router_id LOCAL_ROUTER_ID

# escadm reload

# reboot

Example:

[root@bgp-001 admin]# escadm bgp set --local_ip 198.18.42.124 --anycast_ip 10.0.124.124

--remote_ip 192.168.0.2 --local_as 65124 --remote_as 65000 --local_router_id 198.18.42.124

[root@bgp-002 admin]# escadm bgp set --local_ip 198.18.42.125 --anycast_ip 10.0.124.124

--remote_ip 192.168.0.2 --local_as 65114 --remote_as 65000 --local_router_id 198.18.42.125

Configuring a BGP Router

To configure a BGP router, log in to the BGP router to configure BGP Anycast routing. The required parameters are:

<Router_AS_#> same as --bgp_remote_as above

<Esc_ip_address> must be the ESC VM's IP address configured for BGP advertisement.

<ESC_AS_#> same as --bgp_local_as shown above configure router bgp <Router_AS_#> neighbor <ESC_IP_address>

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Installing Cisco Elastic Services Controller on OpenStack

Important Notes remote-as <ESC_AS_#> address-family ipv6 unicast route-policy anycast-in in route-policy anycast-out out route-policy anycast-in pass end-policy route-policy anycast-out drop end-policy commit

Important Notes

• ESC HA Active/Standby

• An HA Active/Standby failover takes about 2 to 5 minutes. The ESC service will not be available during the switchover time.

• When the switchover is triggered during transactions, all incomplete transactions will be dropped.

The requests should be re-sent by northbound if it does not receive any response from ESC.

• External Storage

• If the active ESC instance is suspended by OpenStack command, the switch over will be triggered but the cinder volume won't be attached to the new active ESC instance. This is not a valid use case for ESC HA Active/Standby.

• Internal Storage

• Two ESC instances have to be deployed to establish the HA Active/Standby solution. The ESC HA

Active/Standby will start to work when both ESC instances are successfully deployed and are able to connect to each other. If you just deploy one ESC instance with HA Active/Standby parameters, the ESC instance keeps Switching-to-Active state and will not be able to provide any service until it reaches its peer.

• Split-brain scenario can still happen in this ESC HA Active/Standby solution, although the chance is very low.

• ETSI-specific Notes

ESC supports ETSI MANO northbound API defined by the European Telecommunications Standards

Institute (ETSI) for NFV Management and Orchestration. The ETSI MANO API is another programmatic interface based on the REST architecture. For more information, see ETSI MANO Compliant Lifecycle

Operations in the Cisco Elastic Services Controller User Guide . Consider the following notes while enabling ETSI service on ESC which is in HA Active/Standby mode:

• The server.address value in the etsi-vnfm.properties

file must be set to a Virtual IP (VIP) address.

This IP address can be used to communicate back to the ETSI services using API callbacks. If the virtual IP address is not specified, the ETSI service startup may fail.

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Installing Cisco Elastic Services Controller on OpenStack

Troubleshooting High Availability Active/Standby

• The ETSI VNFM service and the escadm script generate and maintain the security.user.name and security.user.password property values. You should not change it manually.The

security.user.password is encoded.

Troubleshooting High Availability Active/Standby

• Check for network failures. If a network problem occurs, you must check the following details:

• The IP address assigned is correct, and is based on the OpenStack configuration.

• The gateway for each network interface must be pingable.

• Check the logs for troubleshooting:

• The ESC Admin logs at /var/log/esc/escadm.log

• The ESC manager log at /var/log/esc/escmanager.log

• The AA elector log at /var/log/esc/elector-{pid}.log

• Check for DRBD (Replication based ESC HA Active/Standby) for Internal Storage solution:

• Check the DRBD configuration file at

/etc/drbd.d/esc.res

• Access the DRBD log

•

/var/log/messages|grep drbd

• To collect log files through CLI, use the following command on all ESC nodes: sudo escadm log collect

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

C H A P T E R

Cisco Elastic Services Controller Active/Active

High Availability Overview

This chapter contains the following sections:

•

Cisco Elastic Services Controller Active/Active HA Overview, on page 33

•

ESC Active/Active Architecture, on page 34

Cisco Elastic Services Controller Active/Active HA Overview

ESC supports High Availability (HA) in the form of an Active/Active model. ESC Active/Active HA has three VMs as a cluster in one datacenter.. There are two datacenters. Between the two datacenters, one datacenter acts as active, another acts as standby. ESC Active/Active HA uses Openstack heat template to deploy the three VM cluster in a datacenter.

In a datacenter, ESC service runs on each VM; however, there is only one ESC on a datacenter that runs as cluster leader. DB service runs only on the leader. The ESC services on the other two ESC VMs run as cluster follower. The DB service is only active on ESC services leader VM.

DRBD synchronises the data among ESC VMs. The ESC service on the three ESC VMs connect to the active

DB service. When a leader switchover happens, all the ESC service connects to the newly active DB service.

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

ESC Active/Active Architecture

ESC Active/Active Architecture

Figure 2: Cisco Elastic Services Controller Active/Active Architecture

Installing Cisco Elastic Services Controller on OpenStack

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

C H A P T E R

Installing Active/Active High Availability Cluster

This chapter contains the following sections:

•

Installing Active/Active High Availability Cluster , on page 35

•

Validating Active/Active High Availability Cluster Post Installation, on page 37

•

Adding Default VIM Connector to the Active/Active High Available Cluster, on page 38

•

Adding BGP in an Active/Active Cluster, on page 38

Installing Active/Active High Availability Cluster

To configure the Active/Active HA cluster, you can run the following commands on OpenStack, where openrc my-server is openrc for the OpenStack, and test is the stack name.

source ~/elastic-services-controller/esc-bootvm-scripts/openrc my-server-42 openstack stack create test -t aa.yaml

To check the status of the stack, use the following commands:

• openstack stack list

• openstack stack show test

• openstack stack event list test

Once the stack is in

CREATE_COMPLETE status, you can ssh into the VMs. The openstack stack show test command lists the IP addresses for the 3 VMs, you can use them to access to the VMs.

Note The Active/Active HA Cluster is deployed on OpenStack only.

Setting up the User Configuration

You can configure some of the parameters based on your settings, such as network, subnet, using either static

IP or DHCP to allocate IP address, flavor, image, password, etc. The configurable parameters are available in aa-param.yaml

, Openstack heat environment file, when the ESC cluster is instantiated via heat template

( aa.yaml

To instantiate ESC cluster, use the following example:

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Installing Cisco Elastic Services Controller on OpenStack

Setting up the User Configuration openstack stack create name -t aa.yaml -e aa-params.yaml

The following example shows how to use a static IP address to configure the port while using environment template: sample@my-server-39:~/aa4.5/apr15$ more aa-params.yaml

parameters: network_1_name: network subnet_name: subnetwork esc_1_ip: 172.23.0.228

esc_2_ip: 172.23.0.229

esc_3_ip: 172.23.0.230

Following are the user configurable parameters available in aa.yaml : parameters: network_1_name: type: string description: Name of the image default: network subnet_name: type: string description: subnet name esc_1_ip: type: string description: static IP address of esc-1 VM.

esc_2_ip: type: string description: static IP address of esc-2 VM.

esc_3_ip: type: string description: static IP address of esc-3 VM.

resources: esc_1_port: type: OS::Neutron::Port properties: network_id: { get_param: network_1_name } fixed_ips: [ { "subnet": { get_param: subnet_name}, "ip_address": { get_param: esc_1_ip

} } ] esc_2_port: type: OS::Neutron::Port properties: network_id: { get_param: network_1_name } fixed_ips: [ { "subnet": { get_param: subnet_name}, "ip_address": { get_param: esc_2_ip

} } ] esc_3_port: type: OS::Neutron::Port properties: network_id: { get_param: network_1_name } fixed_ips: [ { "subnet": { get_param: subnet_name}, "ip_address": { get_param: esc_3_ip

} } ]

...omitting...

The following example shows how to use configurable image, flavor, and vm name prefix from environment template. Ensure that the flavor used suits the ESC deployment requirement.

sample@my-server-39:~/aa4.5/apr15$ more aa-params.yaml

parameters:

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Installing Cisco Elastic Services Controller on OpenStack

Validating Active/Active High Availability Cluster Post Installation nameprefix: abc image_name: ESC-5_0_DEV_4 flavor_name: m1.large

sample@my-server-39:~/aa4.5/apr15$

The following example shows how to use configurable image, flavor, and vmnameprefix from heat template: parameters: nameprefix: type: string description: Name prefix of vm default: helen image_name: type: string description: Name of the image default: ESC-5_0_DEV_4 flavor_name: type: string description: Name of the image default: m1.large

esc-1: type: OS::Nova::Server properties: name: str_replace: template: $nameprefix-esc-1 params:

$nameprefix : { get_param: nameprefix } image: { get_param: image_name } flavor: { get_param: flavor_name }

... omitting...

Validating Active/Active High Availability Cluster Post

Installation

To verify all the ESC nodes use the following commands. Here, all ESC nodes implies each VMs.

sample@my-server-39:~$ openstack --insecure server list | grep abc

| 5ea6fc79-2b2a-4064-9c6a-a83d6b06c225 | abc-test-esc-3

| ACTIVE | network=172.23.7.203

| ESC-5_0_DEV_13 | m1.large

| 10e165d9-5015-4b64-88fe-19e874e6e7c1 | abc-test-esc-1

| ACTIVE | network=172.23.7.205

| ESC-5_0_DEV_13 | m1.large

| 35f6bad1-865f-4155-8411-d37e2616e079 | abc-test-esc-2

| ACTIVE | network=172.23.7.204

| ESC-5_0_DEV_13 | m1.large

To find out the leader node, ssh into one of the nodes/VMs and run the following:

[admin@sample-test-esc-1 ~]$ sudo escadm elector dump

{

"[email protected]:42143": {

"state": "FOLLOWER",

"location": "[email protected]:42143",

"service": "esc_service"

"[email protected]:50474": {

"state": "FOLLOWER",

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Installing Cisco Elastic Services Controller on OpenStack

Adding Default VIM Connector to the Active/Active High Available Cluster

}

"location": "[email protected]:50474",

"service": "esc_service"

"[email protected]:59514": {

"state": "LEADER",

"location": "[email protected]:59514",

"service": "esc_service"

}

Adding Default VIM Connector to the Active/Active High

Available Cluster

You can add a default vim connector to the 3 ESC VM cluster in the following two different ways:

Once the 3 ESC VM cluster boots up, use netconf interface to add a default vim connector by using the following command. The vim.xml

is the default vim connector deployment file.

[admin@name-esc-1 ~]$ esc_nc_cli --host db.service.consul --user admin --password

<admin_password> edit-config vim.xml

To configure a default vim connector, you must add the default vim connector configuration inside the heat template day0 file. Add the following block in the write_files section under the cloud-config in aa-day0.yaml file. Once the 3 ESC VM cluster boots up, it creates a default vim connector by its own.

The following example shows how to configure default vim connector in heat template day0 file:

- path: /opt/cisco/esc/esc-config/esc_params.conf

content: | openstack.os_auth_url=http://172.16.103.38:35357/v3 openstack.os_project_name=admin openstack.os_tenant_name=admin openstack.os_user_domain_name=default openstack.os_project_domain_name=default openstack.os_identity_api_version=3 openstack.os_image_api_version=2 openstack.os_username=admin openstack.os_password=password1

Adding BGP in an Active/Active Cluster

To initiate the BGP process, add the anycast IP to the lo device. You can configure it in sys-cfg.yaml

For example:

#cloud-config write_files:

- path: /etc/cloud/cloud.cfg.d/sys-cfg.yaml

content: | network: version: 1 config:

- type: physical name: lo subnets:

- type: static

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Installing Cisco Elastic Services Controller on OpenStack

Adding BGP in an Active/Active Cluster address: 172.23.188.188/23

You must specify the advertise IP for consul. In esc-config.yaml

, add the following: consul: advertise_addr: 172.23.1.149

Following is the example for adding the BGP section: bgp: depend_on: elector:leader anycast_ip: 172.23.188.188/23 local_as: '65001' local_ip: 192.168.1.11

local_router_id: 192.168.1.11

remote_as: '65000' remote_ip: 192.168.1.12

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Adding BGP in an Active/Active Cluster

Installing Cisco Elastic Services Controller on OpenStack

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

C H A P T E R

Managing Cluster in ESC Active/Active High

Availability

This chapter contains the following section:

•

Managing Cluster in ESC Active/Active High Availability, on page 41

Managing Cluster in ESC Active/Active High Availability

To do cluster management in ESC Active/Active HA, you can call some escadm commands on any ESC node and execute it on all nodes in Active/Active cluster.

The following are the supported commands for cluster level calling:

• escadm start

• escadm stop

• escadm geo start/stop

• escadm vim show

Add the option

--cluster to execute any of the previous commands to be executed on all nodes in

Active/Active local cluster:

For example: sudo escadm geo start --v –cluster

The output of the command and exit code of each node are displayed with the IP address of that node to distinguish the execution output, and the output on the local node.

Example for escadm geo start --cluster

[root@name-geo-2-1 admin]# escadm geo start --cluster

192.168.1.13 # remote host exit status : 0

Starting geo service: [OK]

192.168.1.12 # remote host exit status : 0

Starting geo service: [OK]

Starting geo service: [OK] # output of the local node

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Managing Cluster in ESC Active/Active High Availability

Installing Cisco Elastic Services Controller on OpenStack

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

C H A P T E R

Configuring GEO in Active/Active High

Availability

•

Configuring GEO in Active/Active High Availability, on page 43

•

Verifying GEO Services, on page 45

•

Active/Active GEO HA Failure Injection Limitations, on page 46

Configuring GEO in Active/Active High Availability

ESC Active/Active HA has three VMs as a cluster in one datacenter. The second datacenter consists of

GEO-HA.

Following are the 6 pre-defined roles in GEO:

init

: initial role of geo service

pre_primary

primary

pre_secondary

secondary

unknown

: used when consul is not reachable

GEO can change one role to another. Transitions are defined in esc-config.yaml

. Each transition is divided into the following 3 parts:

• from

: current role

• goto

: destination role

• condition

: when GEO changes the role

Transition Conditions

When A/A HA Geo comes up, the primary datacenter has to go through init

, pre_primary

, and primary states; meanwhile, the secondary datacenter has to go through init, pre-secondary, and secondary states. When

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Installing Cisco Elastic Services Controller on OpenStack

Transition Conditions all ESC VMs' health check pass on both primary and secondary datacenters, the ESC A/A HA GEO is up and running. It is ready for use.

Condition Functions

The following are all supported condition functions:

return

: do nothing but return the argument

and

: return true if all arguments are true

: return true if any of the argument is true

len

: return the length of the argument

equals

: return true if all arguments are equal

true

: return true if args can be tested for truth value in python

false

: opposite to 'true'

The following are samples for GEO configurations on primary datacenter: on_init: consul start on_primary: start on_secondary: stop on_stop: consul stop startup: manual transitions:

- condition: return: and:

- equals:

- len: service1

- 3

- equals:

- len: service2

- 3 rise: 3 service1: dc: dc1 name: consul_agent passing: true type: service service2: dc: dc2 name: geo passing: true type: service from: init goto: primary

- condition: fall: 2 return: equals:

- len: service

- 3 service: dc: dc1 name: consul_agent from: primary goto: secondary

The following are samples for GEO configurations on secondary datacenter:

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Installing Cisco Elastic Services Controller on OpenStack

Verifying GEO Services on_init: consul start on_primary: start on_secondary: stop on_stop: consul stop startup: manual transitions:

- condition: return: and:

- equals:

- len: service1

- 3

- equals:

- len: service2

- 3 rise: 3 service1: dc: dc1 name: consul_agent passing: true type: service service2: dc: dc2 name: geo passing: true type: service from: init goto: secondary

- condition: fall: 2 return: equals:

- len: service

- 3 service: dc: dc1 name: consul_agent from: secondary goto: primary

Verifying GEO Services

To start Active/Active GEO-HA, run the following command: escadm geo start

To verify the GEO status, use the following command:

[root@test-geo3-ha-1 esc-scripts]# escadm geo status geo (pgid 3745) is primary

The verify the GEO services in current datacenter, use the following command:

[root@test-geo3-ha-1 esc-scripts]# escadm geo dump

{

"[email protected]:44793": {

"role": "primary",

"location": "[email protected]:44793",

"service": "geo"

"[email protected]:52459": {

"role": "primary",

"location": "[email protected]:52459",

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Installing Cisco Elastic Services Controller on OpenStack

Active/Active GEO HA Failure Injection Limitations

"service": "geo"

"[email protected]:38841": {

"role": "primary",

"location": "[email protected]:38841",

"service": "geo"

}

To verify all the GEO services in the datacenters, use the following command:

[root@test-geo4-ha-1 admin]# escadm geo dump --all

{

"[email protected]:36760": {

"role": "primary",

"location": "[email protected]:36760",

"service": "geo"

"[email protected]:42362": {

"role": "secondary",

"location": "[email protected]:42362",

"service": "geo"

"[email protected]:51936": {

"role": "primary",

"location": "[email protected]:51936",

"service": "geo"

"[email protected]:37604": {

"role": "secondary",

"location": "[email protected]:37604",

"service": "geo"

"[email protected]:44450": {

"role": "primary",

"location": "[email protected]:44450",

"service": "geo"

"[email protected]:34875": {

"role": "secondary",

"location": "[email protected]:34875",

"service": "geo"

}

Active/Active GEO HA Failure Injection Limitations

The ESC Active/Active GEO HA is enhanced to support a one-way GEO HA failover with a maintenance window to move it back to healthy state.

If a GEO failover happens and the ESC VMs move to the unhealthy state, use the following steps to bring

ESC A/A GEO HA back to the healthy state through manual intervention:

Procedure

Step 1 Resolve any issues in Datacenter1 (DC1), that may have caused the failures and enabled the GEO switch to

Datacenter2 (DC2).

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Installing Cisco Elastic Services Controller on OpenStack

Active/Active GEO HA Failure Injection Limitations

Step 2

Step 3

Step 4

Step 5

Ensure that the consul is running in at least 2 nodes in DC1 and DC2.

Run the sudo escadm geo replicate –all command on DC2 when DC1 has at least two nodes with consul in the running state.

Run the sudo escadm stop command on all the 6 ESC VMs.

Run the sudo escadm geo restart command on all the 6 ESC VMs.

What to do next

Note ESC does not support any operations on ESC VMs in DC1 after the GEO HA fails over to DC2.

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Active/Active GEO HA Failure Injection Limitations

Installing Cisco Elastic Services Controller on OpenStack

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

C H A P T E R

DRBD Encryption for ESC Active/Standby and

Active/Active HA Data Replication

This chapter contains the following sections:

•

DRBD Encryption for ESC HA Data Replication , on page 49

•

ESC HA with DRBD Encryption, on page 49

DRBD Encryption for ESC HA Data Replication

ESC uses DRBD for data replication across different nodes in an HA cluster environment. DRBD layers logical block device over existing local block devices on cluster nodes.

The written data to the active node is transferred to the lower-level block device and simultaneously propagated to the secondary node(s). Currently ESC mounts DRBD device directly on

/opt/cisco/esc/esc_database

For Example:

# df

Filesystem devtmpfs tmpfs tmpfs

…

1K-blocks

2961760

2972164

Used Available Use% Mounted on

8748

2961760

2972160

2963416

0% /dev

1% /dev/shm

1% /run tmpfs 594436 0 594436 0% /run/user/1004

/dev/mapper/esc_crypt 3028620 57212 2797848 3% /opt/cisco/esc/esc_database

Block device encryption encrypts or decrypts the data transparently as it is written/read from block devices, the underlying block device sees only encrypted data.

Security is enhanced with the dm-crypt/LUKS layer to encrypt the data in DRBD partition, between filesystem and DRBD device. LUKS (Linux Unified Key Setup) is a specification for block device encryption.

ESC HA with DRBD Encryption

The following bootvm commands boot ESC HA with DRBD encrypted:

Select DRBD LUKS encryption through bootvm.py. There are 4 variations that result in the equivalent ESC day-0 user-data/esc-config.yaml when passed to the ESC VM instance.

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Installing Cisco Elastic Services Controller on OpenStack

ESC HA with DRBD Encryption bootvm.py --fs_encryption_type luks --fs_luks_key_prompt bootvm.py --fs_encryption_type luks --fs_luks_key 'LuksKeyValue'

=> injects the luks key into default file location /opt/cisco/esc/esc-config/luks_key bootvm.py --fs_encryption_type luks --file root:0400:/opt/cisco/esc/esc-config/luks_key:path-to-local-luks-key-file

=> injects a local file containing the luks key

The following command shows an advanced usage to manage the luks key file at a different path on the ESC

VM filesystem: bootvm.py --fs_encryption_type luks --fs_luks_key_file path-on-esc-vm-luks-key-file

--fs_luks_key_prompt bootvm.py --fs_encryption_type luks --fs_luks_key_file path-on-esc-vm-luks-key-file

--fs_luks_key 'LuksKeyValue'

=> injects the luks key into a different file location bootvm.py --fs_encryption_type luks --fs_luks_key_file path-on-esc-vm-luks-key-file --file root:0400:path-on-esc-vm-luks-key-file:path-to-local-luks-key-file

=> injects the luks key as read from a local file into a different file location

Use the following commands if you are installing ESC with a custom user-data, such as ESC Active/Active deployment with heat templates:

The luks key is specified as a day-0 file and an attribute under esc-config.yaml / filesystem.

Encode the luks key as base64: base64 <<<'LuksKeyValue'

THVrc0tleVZhbHVlCg==

Then, insert the previous luks key into the user-data / cloud-config file: write_files:

- path: /opt/cisco/esc/esc-config/luks_key owner: root:root permissions: '400' encoding: b64 content: THVrc0tleVZhbHVlCg==

- path: /opt/cisco/esc/esc-config/esc-config.yaml

owner: root:esc-user permissions: '0640' content: | resources: filesystem: depend_on: drbd:active encryption_type: luks luks_key_file: /opt/cisco/esc/esc-config/luks_key

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

C H A P T E R

Upgrading ESC Active/Active High Availability

This chapter contains the following sections:

•

Upgrading ESC Active/Active High Availability, on page 51

Upgrading ESC Active/Active High Availability

Cisco Elastic Service Controller Active/Active HA supports local Active/Active to Active/Active simple upgrade.

Local Active/Active to Active/Active Simple Upgrade

Procedure

Step 1

Step 2

Step 3

Step 4

Back up the database. For more information, see the section,

Backing up the Database, on page 51

Remove old VMs. For more information, see the section,

Removing the Old VMs, on page 52 Removing

Old VMs .

Install new ESC Active/Active VMs. For more information, see the section,

Installing a New ESC Active/Active

VM, on page 52 .

Restore the ESC database. For more information, see the section,

Restoring the ESC Database, on page 53 .

Backing up the Database

Before upgrade, take the back up of database using the following procedure.

Procedure

Step 1

Step 2

Put the ESC leader VM in the maintenance mode, by running the following command: escadm op_mode set --mode=maintenance

Wait until all the ESC VMs stop processing transactions. To verify, run the following command: escadm ip_trans

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Installing Cisco Elastic Services Controller on OpenStack

Removing the Old VMs

Step 3

Step 4

Create a backup of database on the ESC leader by running the following command: escadm backup --file dbback.tar, scp <dbback.tar>

Collect logs from all the ESC VMs by running the following command: escadm log collect scp

Removing the Old VMs

Procedure

Step 1

Step 2

Shutdown all the ESC follower VMs and the ESC leader VM running the following command: nova stop

Remove old ESC Active/Active VMs from the OpenStack by running the following command: openstack stack delete {stack name}

Installing a New ESC Active/Active VM

After backing up the database and shutting down of the old ESC Active/Active VMs, a new/upgraded (based on new ESC package) Active/Active ESC VM must be installed.

Procedure

Step 1

Step 2

Step 3

Step 4

For OpenStack, register a new image by running the following command: glance image-create

Install the new ESC Active/Active VMs by running the following command: openstack stack create {stack name} --template {location of the template file}

Check all the ESC VMs health, and stop the escadm service in the follower VMs by running the following command: sudo escadm stop for all followers VMs

Once the escadm service is stopped in all the follower VMs, stop the escadm service in the leader VM by running the following command: sudo escadm stop

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Installing Cisco Elastic Services Controller on OpenStack

Restoring the ESC Database

Restoring the ESC Database

Restore the ESC database on the new ESC instance, using the following procedure:

Procedure

Step 1

Step 2

Step 3

Step 4

Step 5

Copy the backup file to the new leader by running the folowing command: scp

Restore the database on the ESC leader by running the following command: sudo escadm restore --file <dbback.tar>

After restoring, the restore process starts the escadm service in the leader VM. However, the escadm service remains to be stopped in all the follower VMs.

Verify that the ESC leader VM is running all the services without any interruption.

Put the ESC leader VM into the operation mode by running the following command: sudo escadm op_mode set --mode=operation

Start the ESC services on the follower VMs by running the following command: sudo escadm start

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Restoring the ESC Database

Installing Cisco Elastic Services Controller on OpenStack

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

P A R T

Installing Cisco Elastic Services Controller on

VMware vCenter

•

Prerequisites, on page 57

•

Installing Cisco Elastic Services Controller on VMware vCenter, on page 61

•

Installing High Availability, on page 69

C H A P T E R

Prerequisites

The following sections detail the prerequisites for installing Cisco Elastic Services Controller:

•

Virtual Resource and Hypervisor Requirements, on page 57

•

vCenter Resources, on page 57

•

Important Notes, on page 58

Virtual Resource and Hypervisor Requirements

The following table lists the prerequisites to install Cisco Elastic Services Controller on VMware vCenter or vSphere:

See the VMware Compatibility Guide to confirm that VMware supports your hardware platform.

Requirement Description

System Requirements

Virtual CPUs

Memory

Disk Space

Hypervisor Requirements

VMware vCenter

VMware vCloud Director (vCD)

4 VCPUs

8 GB RAM

40 GB

ESC supports VMware vCenter version 6.7.

ESC supports VMware vCD version 10.2 (vCloud

API v35.0).

vCenter Resources

Resources to be created/installed on vCenter:

• Datacenters : At least one datacenter. For more details, see the Important Notes below.

• Hosts : Host configuration based on your targeted performance objectives. Each Host under the single vDS must have at least two physical Network Interface Card (NIC) connected, (one for vCenter

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Installing Cisco Elastic Services Controller on VMware vCenter

Important Notes

Management Interface by default, and the other used to assign to VDS's uplink portgroup). This setup is required for data access across hosts.

• Compute Clusters : Clusters can be created to group several hosts together.

• Datastores : Shared datastore is required if user wants to leverage DRS.

• Distributed Switches : At least one distributed switch that will contains all the VNF supporting networks.

Important Notes

Keep in mind the following important notes while installing ESC on a VMware:

• A single ESC instance will only support:

• Multiple Datacenter supported deployment, network, image, subnet creation

• One vSphere Distributed Switch (VDS)

• DPM, HA Active/Standby, and vMotion must be off.

• If DRS is enabled, it has to be in the "Manual Mode".

• Fault Tolerance is not supported.

• Datastore Cluster is not supported, only flat datastore(s) structure under the cluster or under the datacenter are supported.

• ESC only supports a default resource pool. Adding and creating resource pools are not supported.

• Image (Template) created through ESC are stored under /esc-ovas folder .

• Day-0, smart license, and other supported files are packed into a ISO file, and uploaded to the same folder where the VM rest, then mount it as a CD-ROM to the VM.

• ESC/VIM does not respond for the name and file content passed in for generating ISO file. They have to be provided according to each template's requirements. e.g. for ASAv, the day-0 config has to be named as "day0-config", and smart license token has to be named as "idtoken".

• When you see the error message "Networking Configuration Operation Is Rolled Back and a Host Is

Disconnected from vCenter Server", it is due to a vCenter's limitation. See the Troubleshooting guide , page 91 to increase the timeout for rollback.

• The following VM features and operations are not supported in all versions of the Cisco CSR 1000V. If still these operations are used or performed, there may be risk of encountering dropped packets, dropped connections, and other error statistics.

DRS

Suspend

Snapshot

Resume

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Installing Cisco Elastic Services Controller on VMware vCenter

Important Notes

• Although deployments can be processed without shared storage, ESC does not guarantee optimized computing resource. Shared storage(s) should associate with as many as possible hosts, which will give more opportunity to DRS to balance resources.

• Every time a redeploy happens as part of recovery on VMware, VM's interface(s) will have different

MAC addresses.

• All the VM group defined in a datamodel must accompany with a "zone-host" placement policy, meaning the deployment has to be either host-targeted or cluster-targeted.

• Recovery may fail, if a VM has PCI/PCIe passthrough device(s) attached, when it's recovered to a computing-host (picked based on ESC placement algorithm) which does not have any PCI/PCIe passthrough enabled device available .

• For PCI/PCIe passthrough working, DRS has to be off .

• If you experience a PowerOn error on a VM that has PCI/PCIe passthrough device(s) attached to it, update the VM or the image (template) the VM is cloned from, using the solution described here .

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Important Notes

Installing Cisco Elastic Services Controller on VMware vCenter

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

C H A P T E R

Installing Cisco Elastic Services Controller on

VMware vCenter

This chapter describes how to install Cisco Elastic Services Controller on VMware vCenter and includes the following sections:

•

Installing Cisco Elastic Services Controller on VMware vCenter, on page 61

•

Next Steps: Cisco Elastic Services Controller Virtual Machine, on page 67

Installing Cisco Elastic Services Controller on VMware vCenter

Cisco Elastic Services Controller can be installed in a VMware ESXi hypervisor and can be accessed or managed using vSphere client of VMware. You can install Cisco Elastic Services Controller in a VMware environment using an Open Virtual Appliance (OVA) package.

The VMware vSphere client can be connected directly to your ESXi installation, or it can be connected to a vCenter server which in turn is connected to your vSphere installation. Connecting through vCenter provides a number of capabilities that connecting directly to ESXi does not. If a vCenter server is available and associated with the ESXi installation, it should be used.

Preparing to Install Cisco Elastic Services Controller

In order to install Cisco Elastic Services Controller and configure its network connection, you have to answer several questions. Some of these questions concern the networking environment in which the virtual machine is being installed, and some of them concern values which are unique to the particular virtual machine being installed.

Before you perform the installation, ensure that you are prepared by reviewing this checklist:

Requirements Your Information/ Notes

OVA image location

OVA image

VSphere Web Client

Hostname

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Installing Cisco Elastic Services Controller on VMware vCenter

Installing the Elastic Services Controller Using the OVA Image

Requirements

IP address

Subnet mask

Network vCenter IP vCenter Port vCenter credentials

Datacenter Name

Datastore Host

Computer Cluster Name

Your Information/ Notes

Installing the Elastic Services Controller Using the OVA Image

To install Cisco Elastic Services Controller, you must first download the correct installation file.

Using vSphere, connect directly to the ESXi installation or the vCenter server, and select the ESXi installation where the OVA is to be deployed.

This procedure describes how to deploy the Elastic Services Controller OVA image on VMware.

Before you begin

• Set your keyboard to United States English.

• Confirm that the Elastic Services Controller OVA image is available from the VMware vSphere Client.

• Make sure that all system requirements are met as specified in the Chapter 6: Prerequisites.

• Gather the information identified in Preparing to Install Cisco Elastic Services Controller.

Procedure

Step 1

Step 2

Step 3

Using the VMware vSphere Client, log in to the vCenter server.

Choose vCenterHome > Hosts and Clusters . Right click the host where you want to deploy ESC, and then choose Deploy OVF Template .

In the wizard, provide the information as described in the following table:

Screen

Select source

Action

Select the Elastic Services Controller OVA.

Review details

Select name and folder

Review OVF Template details.

Enter a name and select a folder for the VM.

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Installing Cisco Elastic Services Controller on VMware vCenter

Screen

Select configuration

Select a resource

Select storage

Select networks

Customize template

Bootstrap Properties

Username

Password

Host name

Network IP

Network Gateway

Enable Https Rest

Enable Portal startup

VIM Settings of vCenter Server vCenter IP vCenter Port vCenter Username vCenter Password

Installing the Elastic Services Controller Using the OVA Image

Action

Select any one of the following deployment configurations:

• Large, 1 Network

• Large, 2 Networks

• Large, 3 Networks

Select the host or cluster to run the ESC template.

Select a location to store the files for the VM and a provisioning type. The storage can be local or shared remote, such as NFS or SAN.

You can choose either Thin provisioned format or

Thick provisioned format to store the VM virtual disks.

Based on the Network configuration for the deployment selected in the Select configuration option, you can allocate the pre-configured networks in vCenter to ESC network interfaces.

Administrator username for remote login.

Administrator password.

VM Hostname.

VM IP address.

Gateway IP address.

Enable external REST interface over HTTPS on port

8443.

Enable Portal startup at port 9001 (for https).

IP address of vCenter server for VNF deployment .

Port of the vCenter server.

Username to access vCenter server.

Password to access vCenter server.

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Installing Cisco Elastic Services Controller on VMware vCenter

Installing Elastic Services Controller Using OVF Tool

Step 4

Step 5

Step 6

Step 7

Screen

Datacenter Name

Datastore Name

Datastore Host

Ready to Complete

Public Key

ConfD Username

ConfD Password

ConfD Public Key

Action

Name of the Datacenter in target vCenter for VNF deployment (Default VDC after Multi-VDC supported)

The destination datastore of all the image (template) create through ESC .

The destination computing-host of all the image

(template) create through ESC.

Review the deployment settings.

Caution Any discrepancies can cause VM booting issues. Carefully review the IP address, subnet mask, and gateway information for accuracy.

Administrator authorized public key for remote login.

Administrator username for netconf and ConfD CLI.

Administrator password for netconf and ConfD CLI.

Administrator authorized public key for netconf and

ConfD CLI.

Check the Power on after deployment check box to power on the VM after deployment.

Click Finish .

A progress indicator shows the task progress until Elastic Services Controller is deployed.

After Elastic Services Controller is successfully deployed, click Close .

Power on the Elastic Services Controller VM.

Installing Elastic Services Controller Using OVF Tool

In addition to installing the Elastic Services Controller using the OVA image, you can use the VMware OVF

Tool, a command-line client, to install Elastic Services Controller on VMware vCenter or vSphere.

To install Elastic Services Controller (ESC) from the command line, do the following:

Procedure

Step 1 Use the probe mode to learn the properties of the OVA package. The probe mode allows you to investigate the contents of a source.

To invoke the probe mode, use the ovftool command with only a source and no target.

>ovftool <source locator>

The following example shows the result of probing the ESC OVA.

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Installing Cisco Elastic Services Controller on VMware vCenter

Installing Elastic Services Controller Using OVF Tool

Step 2

NETWORK_OVA= (Path to the OVA Package)

NETWORK_HOSTNAME="$ (User Name) "

NETWORK_GATEWAY="192.0.2.1"

NETWORK_NET1_IP="192.0.2.0.xx/24" #

NETWORK_NET2_IP="192.51.100.xx/24"

ADMIN_USERNAME=" (admin name) "

ADMIN_PASSWORD=" (password) "

HTTPS_REST="True"

VMWARE_VCENTER_PORT='80'

VMWARE_VCENTER_IP='192.0.2.0.xx'

VMWARE_DATASTORE_HOST='192.0.2.0.xx'

VMWARE_DATACENTER_NAME='DC-NETWORK-1'

VMWARE_DATASTORE_NAME='cluster-datastore1'

VMWARE_COMPUTE_CLUSTER_NAME='DC-CLUSTER-1'

VMWARE_VCENTER_USERNAME='root'

VMWARE_VCENTER_PASSWORD=' password '

VMWARE_VCENTER_FOLDER="$USER"

# All valid deployment options:

4CPU-8GB (default)

4CPU-8GB-2Net

# 4CPU-8GB-3Net

DEPLOYMENT_OPTION="4CPU-8GB-2Net"

Before you deploy the ESC OVA, configure the properties of the OVA packages. Ensure the following OVA package properties are updated for the ESC OVA: NETWORK_OVA, NETWORK_HOSTNAME,

VMWARE_VCENTER_FOLDER, NETWORK_NET1_IP, NETWORK_NET2_IP, and

VMWARE_VCENTER_FOLDER.

The OVA descriptors contain configuration properties for the OVA package. You can set only one property at a time, but you can have multiple instances of the option per command. For multiple property mappings, repeat the option, separating them with a blank, for example --prop:p1=v1 --prop:p2=v2 --prop:p3=v3.

>.ovftool/ovftool\

--powerOn \

--acceptAllEulas \

--noSSLVerify \

--datastore=$VMWARE_DATASTORE_NAME \

--diskMode=thin \

--name=$NETWORK_HOSTNAME \

--deploymentOption=$DEPLOYMENT_OPTION \

--vmFolder=$VMWARE_VCENTER_FOLDER \

--prop:admin_username=$ADMIN_USERNAME --prop:admin_password=$ADMIN_PASSWORD \

--prop:admin_username=admin \

--prop:admin_password='Strong4Security!' \

--prop:confd_admin_username=admin \

--prop:confd_admin_password='Strong4Security!' \

--prop:network_hostname=$NETWORK_HOSTNAME \

--prop:vmware_vcenter_port=$VMWARE_VCENTER_PORT \

--prop:vmware_vcenter_ip=$VMWARE_VCENTER_IP \

--prop:vmware_datastore_host=$VMWARE_DATASTORE_HOST \

--prop:vmware_datacenter_name=$VMWARE_DATACENTER_NAME \

--prop:vmware_vcenter_username=$VMWARE_VCENTER_USERNAME \

--prop:vmware_datastore_name=$VMWARE_DATASTORE_NAME \

--prop:vmware_compute_cluster_name=$VMWARE_COMPUTE_CLUSTER_NAME \

--prop:vmware_vcenter_password=$VMWARE_VCENTER_PASSWORD \

--prop:net1_ip=$NETWORK_NET1_IP \

--prop:net2_ip=$NETWORK_NET2_IP \

--prop:gateway=$NETWORK_GATEWAY \

--prop:https_rest=$HTTPS_REST \

--net:"Network1=VM Network" --net:"Network2=MgtNetwork" --net:"Network3=VNFNetwork" \

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Installing Cisco Elastic Services Controller on VMware vCenter

Powering on Cisco Elastic Services Controller Virtual Machine

Step 3

$NETWORK_OVA vi://$VMWARE_VCENTER_USERNAME:$VMWARE_VCENTER_PASSWORD@$VMWARE_VCENTER_IP/$VMWARE_DATACENTER_NAME/ host/$VMWARE_COMPUTE_CLUSTER_NAME

Following are some advanced examples of passing user credentials through properties.

Advanced usage with password hash:

--prop:admin_username=admin \

--prop:admin_password='$6$wnOi$UDOQmkKm2tQtr2jDVNhoo4wS42ffYYmzxMXLDugfzTbTXmMQDw146VzpxQvMumeaa125.agYHZUqQ8L.sdM2v0'

--prop:confd_admin_username=admin \

--prop:confd_admin_password='$6$wnOi$UDOQmkKm2tQtr2jDVNhoo4wS42ffYYmzxMXLDugfzTbTXmMQDw146VzpxQvMumeaa125.agYHZUqQ8L.sdM2v0'

Advanced usage with password hash and authorized public key:

--prop:admin_username=admin \

--prop:admin_password='$6$wnOi$UDOQmkKm2tQtr2jDVNhoo4wS42ffYYmzxMXLDugfzTbTXmMQDw146VzpxQvMumeaa125.agYHZUqQ8L.sdM2v0'

--prop:admin_public_key='ssh-rsa

AAAAB3NzaC1yc2EAAAABIwAAAIEAu+nkTtu2pShVbTYL+mmKxtmzM5dNXFy8IeX/lH5fXsODH1EAySlzHGFXq36RT5vIG/

+c2uV8fRsWaY7xXDrdGICxfkPuEj2UQH2MQx2yFjMFcaSAT56hsqE= admin@net' \

--prop:confd_admin_username=admin \

--prop:confd_admin_password='$6$wnOi$UDOQmkKm2tQtr2jDVNhoo4wS42ffYYmzxMXLDugfzTbTXmMQDw146VzpxQvMumeaa125.agYHZUqQ8L.sdM2v0'

--prop:confd_admin_public_key='ssh-rsa

AAAAB3NzaC1yc2EAAAABIwAAAIEAu+nkTtu2pShVbTYL+mmKxtmzM5dNXFy8IeX+xXu6TT2sTsxkKtVy8uOAeBp1qKzkp+ c2uV8fRsWaY7xXDrdGICxfkPuEj2UQH2MQx2yFjMFcaSAT56hsqE= admin@net' \

Note You need to replace the variables (IP addresses, root password, VM names, and so on) in the examples above with values from your own system.

To deploy the OVA package with the VMware OVF Tool, use the following command syntax:

>ovftool <source locator> <target locator> where <source locator> is the path to the OVA package and <target locator> is the path target for the virtual machine, OVA package or VI. A VI location refers to any location on a VMware product, such as vSphere,

VMware Server or ESXi. For more information on the VMware OVF Tool, see the VMware OVF Tool user documentation.

The ESC VM is deployed on VMware and powered on automatically.

Powering on Cisco Elastic Services Controller Virtual Machine

To power on the Cisco Elastic Services Controller virtual machine (VM):

Note You must set the memory and CPUs based on the requirements prior to clicking the power on. Once you start the VM you cannot change the memory or CPU settings until you shut down.

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Installing Cisco Elastic Services Controller on VMware vCenter

Next Steps: Cisco Elastic Services Controller Virtual Machine

Procedure

Step 1

Step 2

After deploying the VM, select the virtual machine name in vSphere, right-click on it and select Open Console .

Click the Power on button ( ). During the initial boot of the newly deployed machine, you will be prompted to enter a root (system) password, which is not the Cisco Elastic Services Controller portal password.

Initialization may vary depending on the setup.

Note This is the root password for the underlying Linux operating system on which the Cisco Elastic

Services Controller portal is installed. You will be asked to enter this password twice. You will need root access to the underlying Linux operating system at various times in the future, so make sure that you remember this password.

The End User License Agreement window appears on the first boot. Read the license agreement in its entirety, and only if you understand and accept the license terms, enter y (Yes).

Next Steps: Cisco Elastic Services Controller Virtual Machine

Logging in to Cisco Elastic Services Controller Portal

Configuring the Virtual Machine to Automatically Power Up

You can configure the ESXi hypervisor to automatically power up the ESC VM when power is restored to the ESXi hypervisor layer.

Note You must manually power up the VM.

Procedure

Step 1

Step 2

Step 3

Step 4

Step 5

In the vSphere client, select the ESXi machine to which you are connected. It is not a specific VM that you have to select but the ESXi hypervisor on which they reside.

Select the Configuration tab.

Click the Virtual Machine Startup/Shutdown link under the Software area. You should see the VM in the list shown in window.

Click the Properties...

link present at the top right corner of the page. If you do not see that, resize the window until you do.

The Virtual Machine Startup and Shutdown page is displayed.

Check the Allow virtual machines to start and stop automatically with the system check box.

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Installing Cisco Elastic Services Controller on VMware vCenter

Configuring the Virtual Machine to Automatically Power Up

Step 6

Step 7

Select the virtual machine running ESC and use the Move Up button on the right to move it up into the group labeled Automatic Startup

Click OK

This ensures that whenever power is restored to the ESXi hypervisor, the ESC VM powers up automatically.

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

C H A P T E R

Installing High Availability

This chapter contains the following sections:

•

High Availability Active/Standby Overview, on page 69

•

How High Availability Active/Standby Works, on page 69

•

Deploying ESC High Availability Active/Standby with User Data (HA Active/Standby Pair), on page

•

Deploying ESC High Availability Active/Standby (Standalone Instances), on page 74

•

Important Notes for ESC HA Active/Standby, on page 75

•

Troubleshooting High Availability Active/Standby, on page 75

High Availability Active/Standby Overview

ESC supports High Availability (HA) in the form of Active/Standby and Active/Active models. For

Active/Standby model, two ESC instances are deployed in the network to prevent ESC failure and provide

• Network failures

• Power failures

• Dead VM instance

• Scheduled downtime

• Hardware issues

• Internal application failures

How High Availability Active/Standby Works

A High Availability Active/Standby deployment consists of two ESC instances: an active and a standby.

Under normal circumstances, the active ESC instance provides the services. The corresponding standby instance is passive. The standby instance is in constant communication with the active instance and monitors the active instances' status. If the active ESC instance fails, the standby instance automatically takes over the

ESC services to provide ESC service with minimum interruption.

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Deploying ESC High Availability Active/Standby with User Data (HA Active/Standby Pair)

Installing Cisco Elastic Services Controller on VMware vCenter

The standby also has a complete copy of the database of the active, but it does not actively manage the network until the active instance fails. When the active instance fails, the standby takes over automatically. Standby instance takes over active instance to manage the services while active instance restoration taken place.

When the failed instance is restored, failback operations can be initiated to resume network management via the original active instance.

ESC instances are managed by using KeepAliveD service. The VM handshake between ESC instances occurs through the KeepAliveD over the IPv4 network.

Deploying ESC High Availability Active/Standby with User Data

(HA Active/Standby Pair)

Before you begin:

• Cisco Elastic Services Controller (ESC) High Availability (HA) Active/Standby requires a network to keep alive and replicate database between active and standby nodes. Both ESC VMs must have at least one network interface connecting to the same network and must be able to communicate to each other through the network.

• Ensure the two ESC VMs are located in different hosts and datastores so that single point failures can be prevented.

You can deploy ESC HA Active/Standby on VMware vCenter or vSphere in either of two ways:

• Deploying ESC HA Active/Standby with user data as a High Availability Active/Standby pair (Supported from ESC 4.2)

• Deploying ESC HA Active/Standby as two standalone instances and then using post configuration to set them as a High Availability pair. For more information,see the section on "Deploying ESC High

Availability Active/Standby (Standalone Instances)".

To deploy ESC HA Active/Standby on VMware vCenter or vSphere with user data as a High Availability

Active/Standby pair, define the user data file for each HA Active/Standby instance and then point the user data for each instance via ovftool. The encoding of user data is done via a set of commands in the ovftool script, and the result of this is set as a variable to the –prop:user-data= property in the ovftool.

Note The admin user/password and confd user/password properties are mandatory OVF properties. These properties cannot be defined in the user-data files.

• Define the two VMs for ESC HA Active/Standby.

User Data 1

#cloud-config ssh_pwauth: True write_files:

- path: /etc/cloud/cloud.cfg.d/sys-cfg.yaml

content: | network: version: 1 config:

- type: nameserver address:

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Installing Cisco Elastic Services Controller on VMware vCenter

Deploying ESC High Availability Active/Standby with User Data (HA Active/Standby Pair)

- 161.44.124.122

- type: physical name: eth0 subnets:

- type: static address: 172.16.0.0

netmask: 255.255.255.0

routes:

- gateway: 172.16.0.0

network: 0.0.0.0

netmask: 0.0.0.0

- path: /opt/cisco/esc/esc-config/esc-config.yaml

content: | resources: confd: option: start-phase0 drbd: nodes:

- 172.16.0.0

- 172.16.1.0

run_forever: true esc_service: depend_on: filesystem type: group escmanager: depend_on:

- pgsql

- mona

- vimmanager etsi: depend_on: pgsql startup: false filesystem: depend_on: drbd:active keepalived: vip: 172.16.2.0

portal: depend_on: escmanager startup: false snmp: startup: false runcmd:

- [ cloud-init-per, once, escadm_ovf_merge, sh, -c, "/usr/bin/escadm ovf merge"]

- [ cloud-init-per, once, escservicestart, sh, -c, "chkconfig esc_service on && service esc_service start"]

User data 2

#cloud-config ssh_pwauth: True write_files:

- path: /etc/cloud/cloud.cfg.d/sys-cfg.yaml

content: | network: version: 1 config:

- type: nameserver address:

- 161.44.124.122

- type: physical name: eth0 subnets:

- type: static address: 172.16.1.0

netmask: 255.255.255.0

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Deploying ESC High Availability Active/Standby with User Data (HA Active/Standby Pair)

Installing Cisco Elastic Services Controller on VMware vCenter routes:

- gateway: 172.16.0.0

network: 0.0.0.0

netmask: 0.0.0.0

- path: /opt/cisco/esc/esc-config/esc-config.yaml

content: | resources: confd: option: start-phase0 drbd: nodes:

- 172.16.0.0

- 172.16.1.0

run_forever: true esc_service: depend_on: filesystem type: group escmanager: depend_on:

- pgsql

- mona

- vimmanager etsi: depend_on: pgsql startup: false filesystem: depend_on: drbd:active keepalived: vip: 172.16.2.0

portal: depend_on: escmanager startup: false snmp: startup: false runcmd:

- [ cloud-init-per, once, escadm_ovf_merge, sh, -c, "/usr/bin/escadm ovf merge"]

- [ cloud-init-per, once, escservicestart, sh, -c, "chkconfig esc_service on && service esc_service start"]

• OVFtool should be called twice - once for each VM instance. Each instance needs to provide a

"--prop:user-data" property to point to its hashed user-data.

• Here is an example to boot a pair of HA Active/Standby instances that use 172.16.0.0 and 172.16.1.0

(floating) IPs to its instances, and 172.16.2.0 as a KAD_VIP.

user_data_1=`cat ./user-data-1` user_data_2=`cat ./user-data-2` dec_user_data_1=`echo "$user_data_1" | base64 | tr -d '[:space:]'` dec_user_data_2=`echo "$user_data_2" | base64 | tr -d '[:space:]'`

# vcenter-16 is the developer lab for vmware5

ESC_OVA=/scratch/BUILD-${ESC_IMAGE}/BUILD-${ESC_IMAGE}/ESC-${ESC_IMAGE}.ova

# All valid deployment options:

# 2CPU-4GB

4CPU-8GB (default)

4CPU-8GB-2Net

# 4CPU-8GB-3Net

DEPLOYMENT_OPTION="4CPU-8GB-2Net" deploy_vmware_vm1() {

/usr/bin/ovftool \

--powerOn \

--acceptAllEulas \

--noSSLVerify \

--datastore=$VM_WARE_DATASTORE_NAME \

--diskMode=thin \

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Installing Cisco Elastic Services Controller on VMware vCenter

Deploying ESC High Availability Active/Standby with User Data (HA Active/Standby Pair)

--name=$INSTANCE_NAME"-0" \

--deploymentOption=$DEPLOYMENT_OPTION \

--vmFolder=$FOLDER \

--prop:admin_username=$ESC_VM_USERNAME --prop:admin_password=$ESC_VM_PASSWORD \

--prop:esc_hostname=$INSTANCE_NAME"-0" \

--prop:rest_username=$REST_USERNAME \

--prop:rest_password=$REST_PASSWORD \

--prop:portal_username=$PORTAL_USERNAME \

--prop:portal_password=$PORTAL_PASSWORD \

--prop:confd_admin_username=$CONFD_USERNAME \

--prop:confd_admin_password=$CONFD_PASSWORD \

--prop:vmware_vcenter_port=$VMWARE_VCENTER_PORT \

--prop:vmware_vcenter_ip=$VM_WARE_VCENTER_IP \

--prop:vmware_datastore_host=$VM_WARE_DATASTORE_HOST \

--prop:vmware_datacenter_name=$VM_WARE_DATACENTER_NAME \

--prop:vmware_vcenter_username=$VM_WARE_VCENTER_USERNAME \

--prop:vmware_datastore_name=$VM_WARE_DATASTORE_NAME \

--prop:vmware_vcenter_password=$VM_WARE_VCENTER_PASSWORD \

--prop:net1_ip=$NET1_IP1 \

--prop:net2_ip=$NET2_IP1 \

--prop:gateway=$ESC_GATEWAY \

--prop:https_rest=$HTTPS_REST \

--prop:user-data=$dec_user_data_1 \

--net:"Network1=VM Network" --net:"Network2=MgtNetwork" --net:"Network3=VNFNetwork" \

$ESC_OVA vi://$VM_WARE_VCENTER_USERNAME:$VM_WARE_VCENTER_PASSWORD@$VM_WARE_VCENTER_IP/

$VM_WARE_DATACENTER_NAME/host/$VM_WARE_DATASTORE_CLUSTER

} deploy_vmware_vm2() {

/usr/bin/ovftool \

--powerOn \

--acceptAllEulas \

--noSSLVerify \

--datastore=$VM_WARE_DATASTORE_NAME \

--diskMode=thin \

--name=$INSTANCE_NAME"-1" \

--deploymentOption=$DEPLOYMENT_OPTION \

--vmFolder=$FOLDER \

--prop:admin_username=$ESC_VM_USERNAME --prop:admin_password=$ESC_VM_PASSWORD \

--prop:esc_hostname=$INSTANCE_NAME"-1" \

--prop:rest_username=$REST_USERNAME \

--prop:rest_password=$REST_PASSWORD \

--prop:portal_username=$PORTAL_USERNAME \

--prop:portal_password=$PORTAL_PASSWORD \

--prop:confd_admin_username=$CONFD_USERNAME \

--prop:confd_admin_password=$CONFD_PASSWORD \

--prop:vmware_vcenter_port=$VMWARE_VCENTER_PORT \

--prop:vmware_vcenter_ip=$VM_WARE_VCENTER_IP \

--prop:vmware_datastore_host=$VM_WARE_DATASTORE_HOST \

--prop:vmware_datacenter_name=$VM_WARE_DATACENTER_NAME \

--prop:vmware_vcenter_username=$VM_WARE_VCENTER_USERNAME \

--prop:vmware_datastore_name=$VM_WARE_DATASTORE_NAME \

--prop:vmware_vcenter_password=$VM_WARE_VCENTER_PASSWORD \

--prop:net1_ip=$NET1_IP2 \

--prop:net2_ip=$NET2_IP2 \

--prop:gateway=$ESC_GATEWAY \

--prop:https_rest=$HTTPS_REST \

--prop:user-data=$dec_user_data_2 \

--net:"Network1=VM Network" --net:"Network2=MgtNetwork" --net:"Network3=VNFNetwork" \

$ESC_OVA vi://$VM_WARE_VCENTER_USERNAME:$VM_WARE_VCENTER_PASSWORD@$VM_WARE_VCENTER_IP/

$VM_WARE_DATACENTER_NAME/host/$VM_WARE_DATASTORE_CLUSTER

} deploy_vmware_vm1 deploy_vmware_vm2

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Installing Cisco Elastic Services Controller on VMware vCenter

Deploying ESC High Availability Active/Standby (Standalone Instances)

• Once the VMs are deployed successfully, you can check the status of ESC HA Active/Standby. You will find that one VM instance is booted as ACTIVE while the other VM instance is a STANDBY.

Deploying ESC High Availability Active/Standby (Standalone

Instances)

To deploy ESC HA Active/Standby on VMware vCenter or vSphere, two separate standalone nodes need to be installed first. After the standalone ESC instances are installed, reconfigure these nodes to turn them into active and standby using the following:

• kad_vip

• kad_vif

• ha_node_list

Note • On each ESC VM, we need to run escadm tool to configure ESC HA Active/Standby parameters and then reload and restart the escadm service.

• When you are deploying ESC HA Active/Standby, the kad_vip argument allows end users to access the active ESC instance.

Procedure

Step 1

Step 2

As an admin user, run the escadm tool on both the active and standby instances and provide the corresponding arguments.

• kad_vip — Specifies the IP address for Keepalived VIP (virtual IP) plus the interface of Keepalived VIP

[ESC-HA Active/Standby]

• kad_vif — Specifies the interface for Keepalived virtual IP and keepalived VRRP [ESC-HA

Active/Standby]. You can also use this argument to only specify the interface for keepalived VRRP, if the VIP interface is already specified using the kad_vip argument.

• ha_node_list — Specifies list of IP addresses for HA Active/Standby nodes in the active/standby cluster for DRDB synchronization. This argument is utilized for replication-based HA Active/Standby solution only. For ESC instances with multiple network interfaces, the IP addresses should be within the network that --kad_vif argument specifies .

Step 3

$ sudo escadm ha set --kad_vip= <ESC_HA_VIP> --kad_vif= <ESC_KEEPALIVE_IF> --ha_node_list=

<ESC_NODE_1_IP> <ESC_NODE_2_IP>

$ sudo escadm reload

$ sudo escadm restart

After the restart, one ESC VM should be in active state and the other one should be in standby state.

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Installing Cisco Elastic Services Controller on VMware vCenter

Important Notes for ESC HA Active/Standby

Step 4

Step 5

Add the VIP to the allowed address pairs for both VMs so that the VIP is reachable from outside.

Verify the status of each ESC instance.

# sudo escadm status

The following table lists few other command to check the status:

Status CLI Commands cat /opt/cisco/esc/keepalived_state ESC HA Active/Standby Role

ESC Health

ESC Service Status sudo escadm health

If you want to see more details (such as status of the

VIM manager, SNMP, portal, ESC manager, keepalived status and so on), add '–v': sudo escadm status --v

To check the detailed status, check the

/var/log/esc/escadm.log

Important Notes for ESC HA Active/Standby

• The HA Active/Standby failover takes about 2 to 5 minutes based on the number of managed VNFs to be operational. ESC service will not be available during the switchover time.

• When the switchover is triggered during transactions, all incomplete transactions will be dropped. The requests should be re-sent by Northbound interface if it does not receive any response from ESC.

Troubleshooting High Availability Active/Standby

• Check for network failures. If a network problem occurs, you must check the following details:

• The IP address assigned is correct, and is based on the OpenStack configuration.

• The gateway for each network interface must be pinged.

• Check the logs for troubleshooting:

• The ESC manager log at /var/log/esc/escmanager.log

• The KeepAliveD log at /var/log/messages by grep keepalived

• The ESC service status log at /var/log/esc/escadm.log

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Troubleshooting High Availability Active/Standby

Installing Cisco Elastic Services Controller on VMware vCenter

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

P A R T

III

Installing Cisco Elastic Services Controller on

VMware vCloud Director

•

Installing Cisco Elastic Services Controller on VMware vCloud Director, on page 79

C H A P T E R

Installing Cisco Elastic Services Controller on

VMware vCloud Director

This chapter describes how to install Cisco Elastic Services Controller on VMware vCloud Director and includes the following sections:

•

Uploading the ESC OVA file into a Catalog in VMware vCloud Director, on page 79

•

Deploying ESC vApp on vCD Web Client, on page 79

•

Adding the VIM Connectors, on page 80

•

Adding Self-Signed Certificate, on page 80

Uploading the ESC OVA file into a Catalog in VMware vCloud

Director

Procedure

Step 1

Step 2

Step 3

Step 4

Step 5

From Catalogs > My Organization's Catalogs , select a catalog.

Under the vApp Templates tab, click Upload

The Upload OVF package as a vApp Template window appears.

In the OVF package field, click Local file . Click Browse and choose the ESC OVA file from the local system.

Click Upload to transfer the ESC OVA file into the catalog.

After uploading the ESC OVA file, you can access the ESC vApp template from the catalog.

Deploying ESC vApp on vCD Web Client

This section describes the deployment scenario for Elastic Services Controller (ESC) and the procedure to deploy ESC vApp on VMware vCloud Director (vCD).

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Installing Cisco Elastic Services Controller on VMware vCloud Director

Adding the VIM Connectors

Resources such as organization, organization VDC, and so on must be created on vCD before deployment.

For more information, see the Managing Resources on vCloud Director (vCD).

To deploy ESC vApp on vCD web client, you must:

Procedure

Step 1

Step 2

Step 3

Step 4

From Catalogs > My Organization's Catalogs, select a Catalog.

Select the ESC vApp template, right click and select Add to My Cloud .

To complete the deployment, you must specify the following in the Add to My Cloud wizard: a) Select Name and Location - Specify ESC as the name of the vApp and select its virtual datacenter.

b) Configure Resources - Specify ESC as the VM name and SharedOnly for storage policy.

c) Network Mapping - Specify interface(s) network type as MgtNetwork,SvcNetwork, and VnfNetwork .

IP allocation is Static-Manual for all types of network in an IPv4.

d) Custom Properties - Fill in the custom properties for day(0) operation.

Note : Do not fill or change anything in the VM Settings of vCenter Server section.

e) Customize Hardware - Specify CPU use, memory consumption, and other core parameters.

f) Ready to Complete - Check the Power on vApp after this wizard is finished on the bottom right corner of the wizard and click Finish.

Adding the VIM Connectors

For more information on configuring VIM connectors after installation and managing VIM connectors, see the Managing VIM Connectors chapter in the Cisco Elastic Services Controller User Guide.

Adding Self-Signed Certificate

If the vCD instance is using a self-signed certificate, use the following command to add the certificate into

ESC, so that it qualifies the SSL verification:

$ escadm truststore add --help usage: escadm truststore add [-h] [-v] --alias ALIAS --file FILE optional arguments:

-h, --help show this help message and exit

-v, --v, --verbose show verbose output

--alias ALIAS

--file FILE

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

P A R T

Installing Cisco Elastic Services Controller on a

Kernel-based Virtual Machine (KVM)

•

Installing Cisco Elastic Services Controller on a Kernel-based Virtual Machine, on page 83

C H A P T E R

Installing Cisco Elastic Services Controller on a

Kernel-based Virtual Machine

This chapter describes how to install Cisco Elastic Services Controller on a Kernel-based Virtual Machine and includes the following sections:

•

Installing Cisco Elastic Services Controller in a Kernel-based Virtual Machine, on page 83

•

Next Steps: Cisco Elastic Services Controller Kernel-based Virtual Machine, on page 86

Installing Cisco Elastic Services Controller in a Kernel-based

Virtual Machine

Cisco Elastic Services Controller can be installed in a Kernel-based Virtual Machine. You can install Cisco

Elastic services controller in a Kernel-based Virtual Machine using libvirt.

Preparing to Install Cisco Elastic Services Controller on a Kernel-based Virtual

Machine

If you plan to run Cisco Elastic Services Controller on a kernel-based virtual machine, make sure the following are setup:

Python 2.7 or 3.x

python-setuptools

Notes

Installed by default on Linux

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Installing Cisco Elastic Services Controller on a Kernel-based Virtual Machine (KVM)

Preparing to Install Cisco Elastic Services Controller on a Kernel-based Virtual Machine pip

OpenStack clients genisoimage libvirt and virtinst

Notes

On RHEL 6.x/7.x: :

# easy_install pip

Since the installation using pip compiles source files, the gcc and python development packages are also required on RHEL. To install these packages on

RHEL:

# yum install gcc python-devel

On RHEL8.x:

# yum install gcc

On Ubuntu : Installed by default. Since the installation using pip compiles source files, the gcc and python development packages are also required on Ubuntu.

To install these packages on Ubuntu:

# apt-get install python-dev

# pip install python-keystoneclient

# pip install python-cinderclient

# pip install python-novaclient

# pip install python-neutronclient

On RHEL :

# yum install genisoimage

On Ubuntu :

# apt-get install genisoimage

For Python 2

On RHEL 6.x

# yum install libvirt-python python-virtinst

On RHEL 7.x

# yum install libvirt-python virt-install

On Ubuntu :

# apt-get install libvirt-dev

# pip install libvirt-python

For Python 3:

On Ubuntu

# sudo apt-get install -y python3-libvirt

On RHEL

# yum install -y python3-libvirt

Virt-Manager git clone https://github.com/virt-manager/virt-manager.git

/usr/share/virt-manager-py3

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Installing Cisco Elastic Services Controller on a Kernel-based Virtual Machine (KVM)

Installing Elastic Services Controller on a Kernel-Based Virtual Machine

Other

Notes

On RHEL 8.x

# yum install libcurl-devel

# yum install openssl-devel

# pip3 install pycurl

# pip3 install urlgrabber

Note libvirt will create the default network automatically.

Installing Elastic Services Controller on a Kernel-Based Virtual Machine

To install standalone Elastic Services Controller (ESC) on a kernel-based virtual machine, do the following:

Procedure

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Load the variables from the openerc file that contains OpenStack credentials: cat ./openrc.sh

export OS_TENANT_NAME='< OS tenant username >' export OS_USERNAME='< OS username >' export OS_PASSWORD='< OS password >' export OS_AUTH_URL='http://<Openstack Host>:5000/v2.0/' source ./openrc.sh

Copy the ESC qcow2 image and the bootvm.py into the kernel-based VM.

Boot ESC on a kernel-based VM on the default network that was created when libvirt was installed, use one of the following command:

./bootvm.py --user_pass <username>:<password> --user_confd_pass <username>:<password>

--libvirt --image <image_name> esc-vm --net <default network>

Boot ESC on a kernel-based VM on the default network with static IP, using the following command:

./bootvm.py --user_pass <username>:<password> --user_confd_pass <username>:<password>

--libvirt --image <image_name> esc-vm --net <network> --ipaddr <ip_address>

Get a list of used IP addresses in your network. Use IP addresses that are not in the list for both HA

Active/Standby bootvm.py command and for kad_vip. Determine the first 3 octets of your network (i.e.

192.168.122) and pass it in the below command : arp -an | grep 192.168.122

To install ESC on a kernel-based VM in high availability, use the following command twice for both the HA nodes:

Note For the second bootvm.py command, use the other HA instance name.

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Installing Cisco Elastic Services Controller on a Kernel-based Virtual Machine (KVM)

Next Steps: Cisco Elastic Services Controller Kernel-based Virtual Machine

./bootvm.py --user_pass <username>:<password> --user_confd_pass <username>:<password>

--libvirt --image <image_name> --ha_mode drbd --gateway_ip <default_gateway_ip_address>

--ipaddr <ip_address>

--ha_node_list <ha peer ip addresses separated by comma> --kad_vip <vip address> esc-ha-1

--net <network>

Next Steps: Cisco Elastic Services Controller Kernel-based

Virtual Machine

Logging in to Cisco Elastic Services Controller Portal

Verifying ESC installation for a Kernel-based Virtual Machine (KVM)

After deploying ESC on a Kernel-based virtual machine, use the following procedure to verify the deployment.

Procedure

Step 1

Step 2

Step 3

Check that the ESC VMs have booted using the following command:

$ virsh list

Get the IP address of the ESC VM, using the following command:

$ arp -an | grep <ip_address>

Connect to ESC using SSH and verify the processes are running:

$ ssh USERNAME@ESC_IP

Troubleshooting Tips

When SSH access is not available, due to network conditions or ESC startup failures, you can connect to ESC through console(if enabled in ESC VM image) or VNC access. To access ESC VM through VNC, do the following:

Identify the vnc port.

virsh dumpxml 10 | fgrep vnc

Create a ssh tunnel to the local vnc port to allow connection from your remote VNC client.

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

P A R T

Installing Cisco Elastic Services Controller on

Amazon Web Services (AWS)

•

Installing Cisco Elastic Services Controller on Amazon Web Services, on page 89

C H A P T E R

Installing Cisco Elastic Services Controller on

Amazon Web Services

This chapter describes how to install Cisco Elastic Services Controller on AWS and includes the following sections:

•

Prerequisites, on page 89

•

Installing the Elastic Services Controller Instance in AWS, on page 90

Prerequisites

Following are the prerequisites that you must complete before you start installing the ESC instance in AWS.

Note If the ESC AMI images are shared with your AWS account, you can ignore these prerequisites and directly use the AMI image for ESC installation.

Procedure

Step 1

Step 2

Step 3

Step 4

Configure AWS CLI . You can use pip to install AWS CLI. For more details, refer to the AWS documentation .

Configure the credentials for AWS CLI based on your account information.

Create an Amazon S3 Bucket. Use this for bucket for uploading ESC image.

Note You must have a role named vmimport that allows importing VM and you must attach an IAM policy to the role. For more information, refer to the documentation on the creation of S3 bucket in

AWS.

Extract the vmdk file from ESC ova file.

$ tar xvf ESC-<latest image file>.ova ESC-<latest image file>-disk1.vmdk

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Installing Cisco Elastic Services Controller on Amazon Web Services (AWS)

Installing the Elastic Services Controller Instance in AWS

Installing the Elastic Services Controller Instance in AWS

Once you have completed the tasks specified in the prerequisites section, you can use the procedure below to deploy and launch ESC instance in AWS.

Procedure

Step 1

Step 2

Upload and register ESC image.

a) Upload the vmdk image to the S3 bucket.

aws s3 cp <esc-vmdk-file> s3://<S3 bucket name>/ b) Register the image.

aws ec2 import-image --description "<esc-vmdk-file>" --disk-containers file://containers.json

Create user data .

a) Create a user for ESC VM. Without a user, you would not be able to access the VM. It is recommended to configure 'admin' user with sudo access and ssh key.

b) Create the esc-config.yaml in user-data using write_files command.

Each instance can have up to 15 interfaces, depending on the type of instances.

Note If you want to use two interfaces, ensure that you create the two network interfaces before hand.

These interfaces on different subnets must belong to the same availability zone. Add the interface details in the 'Configure Instance Details' tab when launching the instance from AWS console.

c) Enable esc_service and start it.

Following is an example of a complete user data:

#cloud-config

# It is recommended to disable password authentication for ssh when ESC runs in public cloud such as AWS.

ssh_pwauth: False users:

- name: admin

# Put admin in 'esc-user' group, otherwise some scripts of ESC might fail when running as admin.

groups: esc-user gecos: User created by cloud-init

# This is an example of the hashed password for 'admin'.

passwd:

$6$rounds=656000$pswsUsR7Iz9NIfA4$7E1sEGV8rhDieNDhc824lYwL3cQ8Rsgp9Nds.OZBe9rG/DE56YWk0kDZoB.DsjATrj9pcBnAe.rSOpWll2r0N/

# The public key for admin user. Replace it with your public key to login.

ssh-authorized-keys:

- ssh-rsa

AAAAB3NzaC1yc2EAAAADAQABAAABAQCqGLe4EVVI/rQy4e4jZUEnc5PvYItc39x5fz9rRggZzpwYzKXSj+UnWQMgvkIai+

Mv5vTPiEYTSNZx9PrnUKayZaLr/2GiLPmnPNEgyzvjD5v77vV3Ag7eHfLXKLYbu7ausYqFKEFbNgSTGC1PWhoz2geY4zNO9hS3eMhNvxNSLpbo3ftzamQoqtWSx2aRc81M/ piy6NcBzJ3JeH4rOk9bQ+QxRAYm3bOlq/qRfuoxmrsgd68xAIXeDWyGumEThXN9MDEcQMIWO54fiPQgkqKbZWztH2EBnE9/B6rZCRBUUvdoQhQt2L/ hbCZN1k+oqQ53rlG/BjT09CGfYbgoHq2v

# false allows you to sudo with the password.

lock-passwd: false homedir: /home/admin

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Installing Cisco Elastic Services Controller on Amazon Web Services (AWS)

Installing the Elastic Services Controller Instance in AWS

# sudo settings sudo: ALL=(ALL) ALL write_files:

- path: /etc/cloud/cloud.cfg.d/sys-cfg.yaml

content: | network: version: 1 config:

# You must define the name server when you use the static IP address.

- type: nameserver address:

- 172.31.0.2

# Define physical network interface

- type: physical name: eth0 subnets:

# Define the static IP address

- type: static address: 172.31.5.66

netmask: 255.255.240.0

# Define the routes routes:

- gateway: 172.31.0.1

# 0.0.0.0 means the default gateway network: 0.0.0.0

netmask: 0.0.0.0

# ESC service config file

- path: /opt/cisco/esc/esc-config/esc-cfg.yaml

content: | confd:

# AAA users for ConfD init_aaa_users:

# Public key for ConfD user 'admin'

- key: c3NoLXJzYSBBQUFBQjNOemFDMXljMkVBQUFBREFRQUJBQUFCQVFDeFkwMzByaEMzSXlWekF2bStISVlmMmpkdm

RUZndTTEpCRjVPTjZoUEgvK2FBTkkzb0NCSmJndjhPdjRtVXUvYmlCYmsyS240QW52Ni9ROE1YWGducnZST241MlJuODN2ejRCWTAw

T1h2SzZrT2YrUnZkSDFtNjhscVlrWU9uZVErNEtOak5tQXRwV0huT0xCZE1mZ2pzTmF1SlF1QVJUMEtDS2VBS3k4aUVqSUZpZDhWZ3

NiSlA0aDNpTzdjcTkza0E1ZGFQb0xiNWRKRVp3ZW15WS9ENGp6ZnJUeDVKWFFuMy80SDdaQVZPaWcyNzBGUnlGVkZhNFl1VXNYcDk1d3

QveHdpc0RUREVCYTYydjkxQzdXamtaNy9rYkRlRW9VSU9OZExqdEdvbU84c2JRUUJoZHBVTTZlNXJkeUl2VzQ3YTZYOFA5N2lBR3JrQ09 qMWVHNkYgeGlhb3hpbnlAWElBT1hJTlktTS1SRVhXCg==

# Note: 'admin' is the only user supported and you cannot change the name here.

name: admin

# Hashed password for admin user.

passwd:

$6$rounds=656000$d4hZHtniblo4/b0m$fD3./1H3jcPlWAENviFlu70i5wKnH9DIasDwTkL.p70UFZlfalzD9O7utL1NdKXwudnNhxIOrvYagkBfq6AWh.

# No specific settings for esc service. Leave it empty.

esc_service: {} runcmd:

- [ cloud-init-per, once, escservicestart, sh, -c, "chkconfig esc_service on && service esc_service start"]

Following is an example to define two interfaces in user data:

- path: /etc/cloud/cloud.cfg.d/sys-cfg.yaml

content: | network: version: 1 config:

- type: physical name: eth0 subnets:

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Installing Cisco Elastic Services Controller on Amazon Web Services (AWS)

Installing the Elastic Services Controller Instance in AWS

Step 3

- type: static address: 172.31.5.66

netmask: 255.255.240.0

# Define the routes routes:

- gateway: 172.31.0.1

# 0.0.0.0 means the default gateway network: 0.0.0.0

netmask: 0.0.0.0

- type: physical name: eth1 subnets:

- type: static address: 172.31.51.220

netmask: 255.255.240.0

Launch ESC VM in AWS

Launch ESC VM using one of the following method:

• From Portal : a.

Go to EC2 Management Console, IMAGES/AMIs. Select the image you imported and click Launch .

Choose an instance type. Choose t2.xlarge as the instance type.

Configure the Instance Details. Add details such as User Data, Storage, Tag name, and so on. While using two interfaces, create these network interfaces and them here.

Configure a security group. Enable ssh only.

Click Launch .

• From Command Line : Choose the image, subnet, security group and use the following command to instantiate ESC VM.

Note aws ec2 run-instances --subnet-id <subnet id> --image-id <image id> --security-group-ids

<security group id> --count 1

--instance-type <instance> --key-name <key name> --user-data <user data file location>

--associate-public-ip-address

ESC does not support HA Active/Standby installation on AWS.

What to do next

After you launch the ESC VM, check the status of the ESC service using the

$ sudo escadm status command.

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

P A R T

Installing Cisco Elastic Services Controller on

Cisco Cloud Services Platform 2100

•

Installing Cisco Elastic Services Controller on Cisco Cloud Services Platform 2100, on page 95

C H A P T E R

Installing Cisco Elastic Services Controller on

Cisco Cloud Services Platform 2100

This chapter describes how to install Cisco Elastic Services Controller on CSP 2100 and includes the following sections:

•

Prerequisites, on page 95

•

Installing the Elastic Services Controller Instance in CSP 2100, on page 95

•

List of Variables Used in CSP 2100 Sample Files, on page 104

Prerequisites

Following are the prerequisites that you require before you start installing the ESC instance in CSP 2100.

• Virtual CPUs 4 (minimum)

• Memory 8 GB

• Disk size 30 GB

Installing the Elastic Services Controller Instance in CSP 2100

Once you have completed the tasks specified in the prerequisites section, you can use the following procedure to deploy and launch ESC instance in CSP 2100. Following are the three deployment alternatives available for CSP 2100.

• ESC with Single and Dual Interfaces

• ESC HA Active/Standby Installation

For list of variables used in the CSP 2100 sample files, see

List of Variables Used in CSP 2100 Sample Files, on page 104

ESC with Single and Dual Interface

To install ESC in CSP, you must create the user-data in the following format as the day0 configuration file:

A sample for single interface describing the day zero file as config drive and user data is as follows:

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Installing the Elastic Services Controller Instance in CSP 2100

Installing Cisco Elastic Services Controller on Cisco Cloud Services Platform 2100

#cloud-config users:

- name: admin gecos: admin

# The user's login name

# The user name's real name groups: esc-user # add admin to group esc-user passwd: $6$saltsalt$9PDBehueUG4XTLEj6BFZA5MDGh/XeQ6QPbf9HYLU3RifHj1

# The hash -- not the password itself -- of the password you want

# to use for this user. You can generate a safe hash via:

# mkpasswd --method=SHA-512 --rounds=4096 lock-passwd: false # Defaults to true. Lock the password to disable password login

# Set to false if you want to password login homedir: /home/admin # Optional. Set to the local path you want to use. Defaults to

/home/<username> sudo: ALL=(ALL) ALL # Defaults to none. Set to the sudo string you want to use ssh_pwauth: True authentication for sshd.

write_files:

# Defaults to False. Set to True if you want to enable password

# ESC Configuration

- path: /opt/cisco/esc/esc-config/esc-config.yaml

content: | resources: confd: init_aaa_users:

- key: c3NoLXJzYSBBQUFBQjNOemFDMXljMkVBQUF passwd: $6$rounds=4096$adWFd7LUn2PEUPWtWPl5tCD7pO9bae672T1 option: start-phase0 escmanager: open_ports:

- '8080'

- '8443' url:

- http://0.0.0.0:8080/ESCManager

- https://0.0.0.0:8443/ESCManager esc_service: type: group

# Params

- path: /opt/cisco/esc/esc-config/esc_params.conf

content: | default.active_vim=CSP default.enable_cascade_deletion=true

# Networking

- path: /etc/sysconfig/network-scripts/ifcfg-eth0 content: |

DEVICE="eth0"

BOOTPROTO="none"

ONBOOT="yes"

TYPE="Ethernet"

USERCTL="yes"

IPADDR="VAR_NETWORK0_IPADDR"

NETMASK="VAR_NETWORK0_NETMASK"

GATEWAY="VAR_NETWORK0_GATEWAY"

DEFROUTE="yes"

NM_CONTROLLED="no"

IPV6INIT="no"

IPV4_FAILURE_FATAL="yes" bootcmd:

- [ cloud-init-per, once, disable_ipv6_eth0, sh, -c, "echo net.ipv6.conf.eth0.disable_ipv6

= 1 >> /etc/sysctl.conf"]

- [ cloud-init-per, once, update_host_name, sh, -c, "echo VAR_LOCAL_HOSTNAME >> /etc/hostname

&& hostnamectl set-hostname VAR_LOCAL_HOSTNAME"]

- [ cloud-init-per, once, update_hosts, sh, -c, "echo 127.0.0.1 VAR_LOCAL_HOSTNAME >>

/etc/hosts"]

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Installing Cisco Elastic Services Controller on Cisco Cloud Services Platform 2100

Installing the Elastic Services Controller Instance in CSP 2100

- [ cloud-init-per, once, add_name_server, sh, -c, "echo nameserver VAR_NAMESERVER_IP >>

/etc/resolv.conf"]

- [ cloud-init-per, once, add_ntp_server, sh, -c, "echo server VAR_NTP_SERVER iburst >>

/etc/ntp.conf"]

- [ cloud-init-per, once, enable_ecdsa-sha2-nistp521, sh, -c, "/usr/bin/ssh-keygen -f

/etc/ssh/ssh_host_ecdsa_521_key -t ecdsa -b 521 -N ''"]

- [ cloud-init-per, once, enable_ecdsa-sha2-nistp384, sh, -c, "/usr/bin/ssh-keygen -f

/etc/ssh/ssh_host_ecdsa_384_key -t ecdsa -b 384 -N ''"]

- [ cloud-init-per, once, enable_ssh_rsa, sh, -c, "sed -i '/ssh_host_rsa_key/s/^#//g'

/etc/ssh/sshd_config"] runcmd:

- [ cloud-init-per, once, apply_network_config, sh, -c, "systemctl restart network"]

- [ cloud-init-per, once, stop_chronyd, sh, -c, "systemctl stop chronyd;systemctl disable chronyd"]

- [ cloud-init-per, once, start_ntp, sh, -c, "systemctl enable ntpd;systemctl start ntpd"]

- [ cloud-init-per, once, set_timezone, sh, -c, "timedatectl set-timezone VAR_TIMEZONE"]

- [ cloud-init-per, once, confd_keygen_root, sh, -c, "/usr/bin/escadm confd keygen --user root"]

- [ cloud-init-per, once, confd_keygen_admin, sh, -c, "/usr/bin/escadm confd keygen --user admin"]

- [ cloud-init-per, once, esc_service_start, sh, -c, "chkconfig esc_service on && service esc_service start"] # You must include this line

A sample for dual interfaces describing the day zero file as config drive and user data is as follows:

You can configure an ethernet-based physical network device with a static IPv4 in ESC .

#cloud-config users:

- name: admin gecos: admin groups: esc-user

# The user's login name

# The user name's real name

# add admin to group esc-user passwd: $6$saltsalt$9PDBehueUG4XTLEj6BFZA5MDGh/XeQ6QPbf9HYLU3RifHj1

# The hash -- not the password itself -- of the password you want

# to use for this user. You can generate a safe hash via:

# mkpasswd --method=SHA-512 --rounds=4096 lock-passwd: false # Defaults to true. Lock the password to disable password login

# Set to false if you want to password login homedir: /home/admin # Optional. Set to the local path you want to use. Defaults to

/home/<username> sudo: ALL=(ALL) ALL # Defaults to none. Set to the sudo string you want to use ssh_pwauth: True authentication for sshd.

write_files:

# ESC Configuration

# Defaults to False. Set to True if you want to enable password

- path: /opt/cisco/esc/esc-config/esc-config.yaml

content: | resources: confd: init_aaa_users:

- key: c3NoLXJzYSBBQUFBQjNOemFDMXljMkVBQUF passwd: $6$rounds=4096$adWFd7LUn2PEUPWtWPl5tCD7pO9bae672T1 option: start-phase0 escmanager: open_ports:

- '8080'

- '8443' url:

- http://0.0.0.0:8080/ESCManager

- https://0.0.0.0:8443/ESCManager esc_service: type: group

# Params

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Installing the Elastic Services Controller Instance in CSP 2100

Installing Cisco Elastic Services Controller on Cisco Cloud Services Platform 2100

- path: /opt/cisco/esc/esc-config/esc_params.conf

content: | default.active_vim=CSP default.enable_cascade_deletion=true

# Networking

- path: /etc/sysconfig/network-scripts/ifcfg-eth0 content: |

DEVICE="eth0"

BOOTPROTO="none"

ONBOOT="yes"

TYPE="Ethernet"

USERCTL="yes"

IPADDR="VAR_NETWORK0_IPADDR"

NETMASK="VAR_NETWORK0_NETMASK"

GATEWAY="VAR_NETWORK0_GATEWAY"

DEFROUTE="yes"

NM_CONTROLLED="no"

IPV6INIT="no"

IPV4_FAILURE_FATAL="yes"

- path: /etc/sysconfig/network-scripts/ifcfg-eth1 content: |

DEVICE="eth1"

BOOTPROTO="none"

ONBOOT="yes"

TYPE="Ethernet"

USERCTL="yes"

IPADDR="VAR_NETWORK1_IPADDR"

NETMASK="VAR_NETWORK1_NETMASK"

GATEWAY="VAR_NETWORK1_GATEWAY"

DEFROUTE="no"

NM_CONTROLLED="no"

IPV6INIT="no"

IPV4_FAILURE_FATAL="yes" bootcmd:

- [ cloud-init-per, once, disable_ipv6_eth0, sh, -c, "echo net.ipv6.conf.eth0.disable_ipv6

= 1 >> /etc/sysctl.conf"]

- [ cloud-init-per, once, update_host_name, sh, -c, "echo VAR_LOCAL_HOSTNAME >> /etc/hostname

&& hostnamectl set-hostname VAR_LOCAL_HOSTNAME"]

- [ cloud-init-per, once, update_hosts, sh, -c, "echo 127.0.0.1 VAR_LOCAL_HOSTNAME >>

/etc/hosts"]

- [ cloud-init-per, once, add_name_server, sh, -c, "echo nameserver VAR_NAMESERVER_IP >>

/etc/resolv.conf"]

- [ cloud-init-per, once, add_ntp_server, sh, -c, "echo server VAR_NTP_SERVER iburst >>

/etc/ntp.conf"]

- [ cloud-init-per, once, enable_ecdsa-sha2-nistp521, sh, -c, "/usr/bin/ssh-keygen -f

/etc/ssh/ssh_host_ecdsa_521_key -t ecdsa -b 521 -N ''"]

- [ cloud-init-per, once, enable_ecdsa-sha2-nistp384, sh, -c, "/usr/bin/ssh-keygen -f

/etc/ssh/ssh_host_ecdsa_384_key -t ecdsa -b 384 -N ''"]

- [ cloud-init-per, once, enable_ssh_rsa, sh, -c, "sed -i '/ssh_host_rsa_key/s/^#//g'

/etc/ssh/sshd_config"] runcmd:

- [ cloud-init-per, once, apply_network_config, sh, -c, "systemctl restart network"]

- [ cloud-init-per, once, stop_chronyd, sh, -c, "systemctl stop chronyd;systemctl disable chronyd"]

- [ cloud-init-per, once, start_ntp, sh, -c, "systemctl enable ntpd;systemctl start ntpd"]

- [ cloud-init-per, once, set_timezone, sh, -c, "timedatectl set-timezone VAR_TIMEZONE"]

- [ cloud-init-per, once, confd_keygen_root, sh, -c, "/usr/bin/escadm confd keygen --user root"]

- [ cloud-init-per, once, confd_keygen_admin, sh, -c, "/usr/bin/escadm confd keygen --user admin"]

- [ cloud-init-per, once, esc_service_start, sh, -c, "chkconfig esc_service on && service esc_service start"] # You must include this line

Creating ESC passwords to use in Day0 Files

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Installing Cisco Elastic Services Controller on Cisco Cloud Services Platform 2100

Installing the Elastic Services Controller Instance in CSP 2100

When using the Cloud-Init day0 file to deploy an ESC instance, the passwords must be passed in as a hash, and not a plain text.

To create a hashed password, use the mkpasswd tool. The following example shows how to use the mkpasswd tool to create a hashed password.

~$ mkpasswd --method=SHA-512 --rounds=4096

Password:

$6$rounds=4096$Yo11pRsFO$iT5SGMJ6z8WEnmj8TKMdInblgWeb/UChmrsQs3aspx8j.yUuuhxKk2XScOkerWWxpqD5F0sLfC5kzT5t2xGkL1

Procedure

Step 1

Step 2

Upload user-data file to CSP

To deploy ESC, the user-data file must be first uploaded to the CSP node.

Note The path to upload images and day0 files is: /osp/repository scp user-data-esc admin@<CSP_IP_ADDRESS>:/osp/repository

Deploying ESC VM

You must edit configuration to be sent to the CSP node hosting the ESC VM.

Following is the deployment datamodel for single interface. For dual interface, you have two interfaces.

<?xml version="1.0"?>

<name>VAR_SERVICE_NAME</name>

<disk_size>30.0</disk_size>

<disk-resize>true</disk-resize>

<iso_name>ESC-5_0_0_xxx</iso_name> <!-- the name of the ESC image already on the CSP

-->

<vnc_password>password1</vnc_password>

<vnics>

<vnic>

<tagged>false</tagged>

<type>access</type>

<passthrough_mode>none</passthrough_mode>

<model>virtio</model>

<network_name>VAR_NETWORK0_NAME</network_name>

</vnic>

<vnic>

<tagged>false</tagged>

<type>access</type>

<passthrough_mode>none</passthrough_mode>

<model>virtio</model>

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Installing Cisco Elastic Services Controller on Cisco Cloud Services Platform 2100

ESC HA Active/Standby Installation

Step 3

Step 4

Step 5

<network_name>VAR_NETWORK1_NAME</network_name>

</vnic>

</vnics>

<disk_type>ide</disk_type>

<day0_filename>user-data-esc</day0_filename>

<day0-dest-filename>user-data</day0-dest-filename>

<day0-volume-id>cidata</day0-volume-id>

</service>

</services>

Sending Configuration

Use a netconf-console (shipped with ConfD) to deploy ESC on a CSP node.

$ netconf-console --port=2022 --host=<CSP_IP_ADDRESS> --user=CSP_ADMIN_USERNAME

--password=CSP_ADMIN_PASSWORD --edit-config=deployESCHA1.xml

If HA, repeat the command with the configuration for the second ESC.

Configuring the VIM Connector

After ESC has booted, configure the VIM Connectors.

When installing ESC in CSP, no VIM connectors are added by default. To manage VNFs, you must create the VIM connector.

Adding the VIM Connectors

For more information on configuring VIM connectors after installation, and managing VIM connectors, see

Managing VIM Connectors in the Cisco Elastic Services Controller User Guide .

ESC HA Active/Standby Installation

To install ESC in CSP, you must create the user-data in the following format as the day0 configuration file.

For HA, you must define one file for each VM.

For creating ESC passwords to use in Day0 Files, see the Creating ESC passwords to use in Day0 Files section.

A sample for ESC HA Active/Standby installation on node 1 describing the day zero file as config drive and user data is as follows: user-data sample - HA Node 1

#cloud-config users:

- name: admin gecos: admin

# The user's login name

# The user name's real name groups: esc-user # add admin to group esc-user passwd: $6$saltsalt$9PDBehueUG4XTLEj6BFZA5MDGh/XeQ6QPbf9HYLU3RifHj1

# The hash -- not the password itself -- of the password you want

# to use for this user. You can generate a safe hash via:

# mkpasswd --method=SHA-512 --rounds=4096 lock-passwd: false # Defaults to true. Lock the password to disable password login

# Set to false if you want to password login homedir: /home/admin # Optional. Set to the local path you want to use. Defaults to

/home/<username> sudo: ALL=(ALL) ALL # Defaults to none. Set to the sudo string you want to use ssh_pwauth: True # Defaults to False. Set to True if you want to enable password

100

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Installing Cisco Elastic Services Controller on Cisco Cloud Services Platform 2100

ESC HA Active/Standby Installation authentication for sshd.

write_files:

# ESC Configuration

- path: /opt/cisco/esc/esc-config/esc-cfg.yaml

content: | ha: vri: VAR_NETWORK0_KADVRI mode: drbd vip: VAR_NETWORK0_KADVIP vif: eth0 nodes:

- ipaddr: VAR_NETWORK0_IPADDR

- ipaddr: VAR_NETWORK0_IPADDR2 confd: init_aaa_users:

- name: admin passwd: $6$rounds=4096$adWFd7LUn2PEUPWtWPl5tCD7pO9bae672T1 escmanager: open_ports:

- '8080'

- '8443' url:

- http://0.0.0.0:8080/ESCManager

- https://0.0.0.0:8443/ESCManager esc_service: {}

# Params

- path: /opt/cisco/esc/esc-config/esc_params.conf

content: | default.active_vim=CSP default.enable_cascade_deletion=true

# Networking

- path: /etc/sysconfig/network-scripts/ifcfg-eth0 content: |

DEVICE="eth0"

BOOTPROTO="none"

ONBOOT="yes"

TYPE="Ethernet"

USERCTL="yes"

IPADDR="VAR_NETWORK0_IPADDR"

NETMASK="VAR_NETWORK0_NETMASK"

GATEWAY="VAR_NETWORK0_GATEWAY"

DEFROUTE="yes"

IPV6INIT="no"

IPV4_FAILURE_FATAL="yes" bootcmd:

- [ cloud-init-per, once, disable_ipv6_eth0, sh, -c, "echo net.ipv6.conf.eth0.disable_ipv6

= 1 >> /etc/sysctl.conf"]

- [ cloud-init-per, once, update_host_name, sh, -c, "echo VAR_LOCAL_HOSTNAME >> /etc/hostname

&& hostnamectl set-hostname VAR_LOCAL_HOSTNAME"]

- [ cloud-init-per, once, update_hosts, sh, -c, "echo 127.0.0.1 VAR_LOCAL_HOSTNAME >>

/etc/hosts"]

- [ cloud-init-per, once, add_name_server, sh, -c, "echo nameserver VAR_NAMESERVER_IP >>

/etc/resolv.conf"]

- [ cloud-init-per, once, add_ntp_server, sh, -c, "echo server VAR_NTP_SERVER iburst >>

/etc/ntp.conf"]

- [ cloud-init-per, once, enable_ecdsa-sha2-nistp521, sh, -c, "/usr/bin/ssh-keygen -f

/etc/ssh/ssh_host_ecdsa_521_key -t ecdsa -b 521 -N ''"]

- [ cloud-init-per, once, enable_ecdsa-sha2-nistp384, sh, -c, "/usr/bin/ssh-keygen -f

/etc/ssh/ssh_host_ecdsa_384_key -t ecdsa -b 384 -N ''"]

- [ cloud-init-per, once, enable_ssh_rsa, sh, -c, "sed -i '/ssh_host_rsa_key/s/^#//g'

/etc/ssh/sshd_config"] runcmd:

- [ cloud-init-per, once, apply_network_config, sh, -c, "systemctl restart network"]

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

101

Installing Cisco Elastic Services Controller on Cisco Cloud Services Platform 2100

ESC HA Active/Standby Installation

- [ cloud-init-per, once, stop_chronyd, sh, -c, "systemctl stop chronyd;systemctl disable chronyd"]

- [ cloud-init-per, once, start_ntp, sh, -c, "systemctl enable ntpd;systemctl start ntpd"]

- [ cloud-init-per, once, set_timezone, sh, -c, "timedatectl set-timezone VAR_TIMEZONE"]

- [ cloud-init-per, once, confd_keygen_root, sh, -c, "/usr/bin/escadm confd keygen --user root"]

- [ cloud-init-per, once, confd_keygen_admin, sh, -c, "/usr/bin/escadm confd keygen --user admin"]

- [ cloud-init-per, once, esc_service_start, sh, -c, "chkconfig esc_service on && service esc_service start"] # You must include this line

Procedure

Step 1

Step 2

Uploading user-data file to CSP

To deploy ESC, the user-data file must be first uploaded to the CSP node.

Note The path to upload images and day0 files is: /osp/repository scp user-data-esc-ha-1 CSP_ADMIN_USERNAME@<CSP_IP_ADDRESS>:/osp/repository scp user-data-esc-ha-2 CSP_ADMIN_USERNAME@<CSP_IP_ADDRESS>:/osp/repository

Deploying ESC VM

You must edit configuration to be sent to the CSP node hosting the ESC VM.

Following is the deployment datamodel for ESC HA Active/Standby on node 1 : deployESC-HA-1.xml

<?xml version="1.0"?>

<name>VAR_SERVICE_NAME</name>

<disk_size>30.0</disk_size>

<disk-resize>true</disk-resize>

<iso_name>ESC-5_0_0_xxx</iso_name> <!-- the name of the ESC image already on the CSP

-->

<vnc_password>password1</vnc_password>

<vnics>

<vnic>

<tagged>false</tagged>

<type>access</type>

<passthrough_mode>none</passthrough_mode>

<model>virtio</model>

<network_name>VAR_NETWORK0_NAME</network_name>

</vnic>

<vnic>

<tagged>false</tagged>

102

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Installing Cisco Elastic Services Controller on Cisco Cloud Services Platform 2100

ESC HA Active/Standby Installation

Step 3

<type>access</type>

<passthrough_mode>none</passthrough_mode>

<model>virtio</model>

<network_name>VAR_NETWORK1_NAME</network_name>

</vnic>

</vnics>

<disk_type>ide</disk_type>

<day0_filename>user-data-esc</day0_filename>

<day0-dest-filename>user-data</day0-dest-filename>

<day0-volume-id>cidata</day0-volume-id>

</service>

</services>

Following is the deployment datamodel for ESC in HA Active/Standby on node 2 : deployESC-HA-2.xml

deployESC-HA-1.xml

<?xml version="1.0"?>

<name>VAR_SERVICE_NAME</name>

<disk_size>30.0</disk_size>

<disk-resize>true</disk-resize>

<iso_name>ESC-5_0_0_xxx</iso_name> <!-- the name of the ESC image already on the CSP

-->

<vnc_password>password1</vnc_password>

<vnics>

<vnic>

<tagged>false</tagged>

<type>access</type>

<passthrough_mode>none</passthrough_mode>

<model>virtio</model>

<network_name>VAR_NETWORK0_NAME</network_name>

</vnic>

<vnic>

<tagged>false</tagged>

<type>access</type>

<passthrough_mode>none</passthrough_mode>

<model>virtio</model>

<network_name>VAR_NETWORK1_NAME</network_name>

</vnic>

</vnics>

<disk_type>ide</disk_type>

<day0_filename>user-data-esc</day0_filename>

<day0-dest-filename>user-data</day0-dest-filename>

<day0-volume-id>cidata</day0-volume-id>

</service>

</services>

Sending Configuration

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

103

Installing Cisco Elastic Services Controller on Cisco Cloud Services Platform 2100

List of Variables Used in CSP 2100 Sample Files

Step 4

Step 5

Use a netconf-console (shipped with ConfD) to deploy ESC on a CSP node.

$ netconf-console --port=2022 --host=<CSP_IP_ADDRESS> --user=<CSP_ADMIN_USERNAME>

--password=<CSP_ADMIN_PASSWORD> --edit-config=deployESC-HA-1.xml

$ netconf-console --port=2022 --host=<CSP_IP_ADDRESS> --user=<CSP_ADMIN_USERNAME>

--password=<CSP_ADMIN_PASSWORD> --edit-config=deployESC-HA-2.xml

Configuring the VIM Connector

After ESC has booted, configure the VIM Connectors.

When installing ESC in CSP, no VIM connectors are added by default. To manage VNFs, you must create the VIM connector.

Adding the VIM Connectors

For more information on configuring VIM connectors after installation, and managing VIM connectors, see

Managing VIM Connectors in the Cisco Elastic Services Controller User Guide .

List of Variables Used in CSP 2100 Sample Files

To create the user-data file, to configure the ESC you must have values ready for the following list of variables used in the sample files:

Table 2: List of Variables

Variable Name

VAR_TIMEZONE

VAR_SERVICE_NAME

VAR_NTP_SERVER

VAR_NETWORK1_NETMASK

VAR_NETWORK1_NAME

VAR_NETWORK1_IPADDR

VAR_NETWORK1_GATEWAY

VAR_NETWORK0_NETMASK

VAR_NETWORK0_NAME

Purpose

The timezone for the ESC clock to use

The name of the ESC service on the CSP

The IP address of an NTP server

The netmask for the eth1 interface (Dual Interface

ESC)

The name of the network on the CSP where ESC's eth1 interface exists (Dual Interface ESC)

The IP address for the eth1 interface (Dual Interface

ESC)

The gateway for the eth1 interface (Dual Interface

ESC)

The netmask for the eth0 interface

The name of the network on the CSP where ESC's eth0 interface exists

104

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Installing Cisco Elastic Services Controller on Cisco Cloud Services Platform 2100

Variable Name

VAR_NETWORK0_KADVRI

VAR_NETWORK0_KADVIP

VAR_NETWORK0_IPADDR2

VAR_NETWORK0_IPADDR

VAR_NETWORK0_GATEWAY

VAR_NAMESERVER_IP

VAR_LOCAL_HOSTNAME

CSP_IP_ADDRESS

List of Variables Used in CSP 2100 Sample Files

Purpose

The VRRP ID used for HA. Must be unique in the subnet for the HA pair and the same value used on both ESCs

Range is from 1 to 254

The VIP for the HA pair that connects to the current

Active ESC

The IP address for the other ESC's eth0 interface

The IP address for ESC (eth0 interface)

The gateway for the eth0 interface

The IP address of a DNS server

The hostname for ESC

IP address of the CSP 2100 to be used

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

105

List of Variables Used in CSP 2100 Sample Files

Installing Cisco Elastic Services Controller on Cisco Cloud Services Platform 2100

106

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

P A R T

VII

Post Installation Tasks

•

Post Installation Tasks, on page 109

Post Installation Tasks

C H A P T E R

This chapter contains the following sections:

Note It is recommended that you ignore the do not edit message, if you want to modify the cloud-init day-0 configuration, file.

•

Changing the ESC Password , on page 109

•

Configuring Pluggable Authentication Module (PAM) Support for Cisco Elastic Services Controller, on page 113

•

Configuring Cisco Elastic Services Controller as Identity Management Client, on page 115

•

Authenticating REST Requests, on page 117

•

Configuring Openstack Credentials , on page 120

•

Enabling Barbican Client in ESC, on page 126

•

Reconfiguring ESC Virtual Machine, on page 126

•

Verifying ESC Configurations and Other Post-Install Operations , on page 129

•

Logging in to the ESC Portal, on page 132

Changing the ESC Password

You will be forced to change the default password on the first time login. Portal will not let you bypass this step and will keep returning you to this page until you change the default password. After the first time password change, you can change your password using the procedures described in this section. Also, if the user has multiple browsers or tabs or the SAME user is logged on by 2 or more computers and one of the user changes the password then everyone will be logged off and asked to re-enter the new password. The user session has an expiry of 1 hour so if the user is inactive on the portal for an hour then portal will expire the session and the user will have to re-login. If you forgot your password, you can also update or randomly generate the password.

This section discusses how to change the passwords.

Example for REST: sudo escadm rest set --username {USERNAME} --password {PASSWORD}

Example for ETSI: sudo escadm etsi set --rest_user {USERNAME:PASSWORD}

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

109

Post Installation Tasks

Changing the ConfD Netconf/CLI Administrator Password Using the Command Line Interface

Changing the ConfD Netconf/CLI Administrator Password Using the Command Line Interface

After you install ESC, to change the Confd admin password, do the following:

Starting ESC Release 5.4, you cannot execute the confd commands, such as confd_cli. The confd_cli -u admin is replaced with the ssh admin@localhost -p 2024 command.

For information on Installing ESC, see Installing Cisco Elastic Services Controller Using the QCOW Image.

To access the confD cli for an admin account: admin@esc$ ssh admin@localhost -p 2024 admin@localhost's password: ******* admin connected from 127.0.0.1 using ssh on esc admin@esc>

Procedure

Step 1

Step 2

Step 3

Step 4

Step 5

$ ssh USERNAME@ESC_IP

Switch to the admin user.

[admin@esc-ha-0 esc]$ sudo bash

[sudo] password for admin:

Load the ConfD CLI:

$ /opt/cisco/esc/confd/bin/ssh admin@localhost -p 2024

Set the new admin password:

$ configure

$ set aaa authentication users user admin password <new password>

Save the changes.

$ commit

Creating Readonly User Group for ConfD in ESC

ConfD in ESC is enhanced with the introduction of a new group named readonly. If you are a member of readonly group, you can only retrieve the information and you cannot modify the permissions.

You can use 'readonly' as the role name with bootvm. The following example shows how to create two users in ConfD. One is admin and the other is readonly:

# bootvm.py name-500-105-100 --user_confd_pass admin:admin --user_confd_pass readonly:readonly::readonly --user_pass admin:admin --image ESC-5_0_0_105 --net network

For HA A/A, you can use 'readonly' as the group name in aa-day0.yaml Following is the example: confd: init_aaa_users:

- group: readonly

110

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Post Installation Tasks

Creating Readonly User Group for ConfD in ESC name: admin passwd: $6$rounds=4096$Ps1JIjKihRTF$fo8XPBxwEHJWWfNiXDnO269rlhAxAhWBc

PBfGnZxy1gM3QMxcN8jJ6guWt9Bu.ZkWdPt3hr0OghO73Wr3iDHb0

You can also create a confd readonly user after ESC vm is deployed. The following steps create a confd readonly user named 'test' with password 'test':

[root@name-500-155 admin]# /opt/cisco/esc/confd/bin/ssh admin@localhost -p 2024 admin connected from 127.0.0.1 using console on name-500-155 admin@name-500-155> configure

Entering configuration mode private

[ok][2019-12-06 18:17:39]

[edit] admin@name-500-155% set aaa authentication users user test uid 9000 gid 9000 password $0$test homedir /var/confd/homes/test ssh_keydir /var/confd/homes/test/.ssh

[ok][2019-12-06 18:19:15]

[edit] admin@name-500-155% set nacm groups group readonly user-name test

[ok][2019-12-06 18:19:41]

[edit] admin@name-500-155% commit

Commit complete.

[ok][2019-12-06 18:19:47]

[edit] admin@name-500-155%

As a readonly user, you can also access ConfD remotely: name@my-server-39:~$ ssh -p 2024 [email protected]

[email protected]'s password: readonly connected from 172.16.103.46 using ssh on name-500-156 readonly@name-500-156> configure

Entering configuration mode private

[ok][2019-12-13 16:15:33]

[edit] readonly@name-500-156% show esc_datamodel tenants { tenant admin { description "Built-in Admin Tenant"; managed_resource false; vim_mapping true;

}

[ok][2019-12-13 16:15:38]

[edit]

ESC in ConfD sends access-denied error if you fall under readonly ConfD group, and require modify permissions. Following is the example of the access-denied error message:

$ esc_nc_cli --user readonly --password ****** edit-config dep.xml

Configure

/opt/cisco/esc/confd/bin/netconf-console --port=830 --host=127.0.0.1 --user=readonly

--password=****** --edit-config=/tmp/d.xml

<?xml version="1.0" encoding="UTF-8"?>

<rpc-reply xmlns="urn:ietf:params:xml:ns:netconf:base:1.0" message-id="1">

<rpc-error>

<error-type>application</error-type>

<error-tag>access-denied</error-tag>

<error-severity>error</error-severity>

</rpc-error>

</rpc-reply>

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

111

Post Installation Tasks

Changing Linux Account Password

If ESC is configured to use PAM/IDM. The groups in IDM servers are directly mapped to the groups in

ConfD. Hence, the readonly user must be mapped in the IDM group 'readonly'.

For example:

$ ipa group-find --all readonly

---------------

1 group matched

--------------dn: cn=readonly,cn=groups,cn=accounts,dc=linuxsysadmins,dc=local

Group name: readonly

GID: 5003

Member users: readonly ipantsecurityidentifier: S-1-5-21-2222126199-2113948134-574478857-1003 ipauniqueid: 858b8cda-0d34-11ea-bca8-525400b29c19 objectclass: top, groupofnames, nestedgroup, ipausergroup, ipaobject, posixgroup, ipantgroupattrs

----------------------------

Number of entries returned 1

----------------------------

Changing Linux Account Password

Procedure

Step 1

Step 2

$ ssh USERNAME@ESC_IP

To update or generate a random password, use the following command:

/usr/bin/pwqcheck

/usr/bin/pwqgen

Changing the ESC Portal Password

The user can update or reset the default admin password.

Procedure

Step 1

Step 2

Step 3

Switch to the root user.

To update the default admin password or randomly generate a password, use one of the following method:

• Using escadm utility:

To update the default admin password (admin/********):

[root@anyname-v44-52 admin]# sudo escadm portal set --username admin --password ********

Successfully updated password for username admin

To generate a random password:

112

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Post Installation Tasks

Configuring Pluggable Authentication Module (PAM) Support for Cisco Elastic Services Controller

[root@anyname-v44-52 admin]# sudo escadm portal set --username admin

Would you like to use the generated password: "Accent5omit&Wide"?[y|n]y

Successfully updated password for username admin

The --must_change variable will ask the user to change their password at the next login.

The --must_change variable is not applicable for REST users.

[root@anyname-v44-52 admin]# sudo escadm portal set --username admin --must_change

Would you like to use the generated password: "Rainy4Dozen&Behave"?[y|n]y

Successfully reset password for username admin. User must change the password at the next login.

• To reset to a specific password:

[root@anyname-v44-52 admin]# sudo escadm portal set --username admin --password *******

--must_change

Successfully reset password for username admin. User must change the password at the next login.

• Using the bootvm command line:

--user_portal_pass admin:<new password>

• Using the ESC Portal: a.

Choose Accounts Setting on the Navigation menu.

Enter the old password in the Old password field, then enter a new password in the New Password and Confirm Password fields.

Click Update Password .

Configuring Pluggable Authentication Module (PAM) Support for Cisco Elastic Services Controller

You can configure the ESC services to use Pluggable Authentication Modules (PAM) for user authentication in ESC. With Cisco Elastic Services supporting PAM, you can also enable LDAP authentication in ESC. If

PAM is not configured, ESC will continue to use the default authentication method for each ESC service.

The following table lists the commands to enable PAM authentication for each ESC service.

Table 3: Configuring PAM for ESC Services

ESC Service/Component

ESCManager (REST interface)

ESC Monitor (Health API)

Command to configure PAM authentication sudo escadm escmanager set --auth

PAM:<pam_service_name> sudo escadm monitor set --auth

PAM:<pam_service_name>

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

113

Post Installation Tasks

PAM Authentication Service Configurations and User Groups

ESC Service/Component

Confd

Portal

ETSI

Command to configure PAM authentication sudo escadm confd set --auth

PAM:<pam_service_name> sudo escadm portal set --auth

PAM:<pam_service_name> sudo escadm etsi set --pam_service

<pam_service_name>

Note • The SSHD service that runs inside the ESC VM already uses PAM authentication by default.

• If any component sets PAM authentication without specifying the PAM service, ESC defaults to the

PAM service 'system-auth'.

PAM Authentication Service Configurations and User Groups

Each ESC service (listed above) has an associated PAM authentication configuration and a user group to provide specific access control. The user group is defined in the /etc/group file. The admin user is a member of all the groups.

Table 4: PAM Authentication Service Configurations and User Groups

/etc/group portal-user:x:1002:admin rest-user:x:1003:admin confd-user:x:1004:admin etsi-user:x:1005:admin health-user:x:1006:admin

/etc/pam.d

portal-auth rest-auth confd-auth etsi-auth health-auth

For example, to configure PAM authentication for the health API and restrict access only to the health user group, run the following command:

$ sudo escadm monitor set --auth PAM:health-auth

ESC configuration was changed and saved automatically. They will take effect once you restart

ESC service by running "sudo escadm restart"

For adding PAM user to ESC component, see

Adding PAM User to an ESC Service/Component, on page 114 .

Adding PAM User to an ESC Service/Component

You can add the PAM user to the following groups of ESC service:

• rest-user

114

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Post Installation Tasks

Configuring Cisco Elastic Services Controller as Identity Management Client

• confd-user

• portal-user

• etsi-user

• health-user

Perform the following steps to add the PAM user to an ESC service/component:

Procedure

Step 1

Step 2

Step 3

Add a PAM user, by using the following command: sudo passwd pamuser

Changing password for user pamuser.

New password:

Retype new password: passwd: all authentication tokens updated successfully.

Add a PAM user to an ESC service/component group, by using the following command: sudo usermod -a -G <ESC Service Group> pamuser

Note The PAM user must be added to the admin or readonly group for the Confd service

Configuring Cisco Elastic Services Controller as Identity

Management Client

Prerequisites

• Ensure that the Identity Management Client (IDM) server is up and running.

• Ensure that the DNS server in ESC is in working state. So that, ESC interacts with the IDM server using the host name.

The following example shows how ESC (esc-client-500.linuxsysadmins.local) reaches the IDM server

(idmns.linuxsysadmins.local).

[root@esc-client-500 admin]# ping idmns

PING idmns.linuxsysadmins.local (192.168.222.176) 56(84) bytes of data.

64 bytes from idmns.linuxsysadmins.local (192.168.221.176): icmp_seq=1 ttl=64 time=0.492

64 bytes from idmns.linuxsysadmins.local (192.168.221.176): icmp_seq=2 ttl=64 time=0.457

64 bytes from idmns.linuxsysadmins.local (192.168.221.176): icmp_seq=3 ttl=64 time=0.645

You can configure IDM through sssd. ESC provides a PAM configuration file, point to

/etc/pam.d/syste-auth to system-auth-esc-sssd to start configuring services in ESC to work with the IDM server.

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

115

Post Installation Tasks

Configuring Cisco Elastic Services Controller as the Identity Policy and Audit Client

# cd /etc/pam.d

# ln -sf system-auth-esc-sssd system-auth

# ls -al /etc/pam.d/system-auth lrwxrwxrwx. 1 root root 20 Nov 13 00:39 /etc/pam.d/system-auth -> system-auth-esc-sssd

The following table lists the commands to enable IDM authentication for each ESC service.

Table 5: Configuring IDM for ESC Services

ESC Service/Component Command

ESCManager

Command

# sudo escadm escmanager set --auth

PAM:system-auth-esc-sssd

ETSI

ConfD

# sudo escadm etsi set --pam_service system-auth-esc-sssd

# sudo escadm confd set --auth

PAM:system-auth-esc-sssd

Configuring Cisco Elastic Services Controller as the Identity Policy and Audit

Client

To Configure the ESC as an Identity Policy and Audit Client (IPA) client, run the following command: ipa-client-install

Following is the example to configure ESC as the IPA client:

[root@esc-client-500 admin]# ipa-client-install --domain linuxsysadmins.local --server idmns.linuxsysadmins.local --realm LINUXSYSADMINS.LOCAL

WARNING: ntpd time&date synchronization service will not be configured as conflicting service (chronyd) is enabled

Use --force-ntpd option to disable it and force configuration of ntpd

Autodiscovery of servers for failover cannot work with this configuration.

If you proceed with the installation, services will be configured to always access the discovered server for all operations and will not fail over to other servers in case of failure.

Proceed with fixed values and no DNS discovery? [no]: yes

Client hostname: esc-client-500.linuxsysadmins.local

Realm: LINUXSYSADMINS.LOCAL

DNS Domain: linuxsysadmins.local

IPA Server: idmns.linuxsysadmins.local

BaseDN: dc=linuxsysadmins,dc=local

Continue to configure the system with these values? [no]: yes

Skipping synchronizing time with NTP server.

User authorized to enroll computers: admin

Password for [email protected]:

Successfully retrieved CA cert

Subject: CN=Certificate Authority,O=LINUXSYSADMINS.LOCAL

Issuer: CN=Certificate Authority,O=LINUXSYSADMINS.LOCAL

Valid From: 2019-11-12 23:23:32

Valid Until: 2039-11-12 23:23:32

Enrolled in IPA realm LINUXSYSADMINS.LOCAL

Created /etc/ipa/default.conf

Configured sudoers in /etc/nsswitch.conf

Configured /etc/sssd/sssd.conf

116

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Post Installation Tasks

Authenticating REST Requests

Configured /etc/krb5.conf for IPA realm LINUXSYSADMINS.LOCAL

trying https://idmns.linuxsysadmins.local/ipa/json

[try 1]: Forwarding 'schema' to json server 'https://idmns.linuxsysadmins.local/ipa/json' trying https://idmns.linuxsysadmins.local/ipa/session/json

[try 1]: Forwarding 'ping' to json server

'https://idmns.linuxsysadmins.local/ipa/session/json'

[try 1]: Forwarding 'ca_is_enabled' to json server

'https://idmns.linuxsysadmins.local/ipa/session/json'

Systemwide CA database updated.

Adding SSH public key from /etc/ssh/ssh_host_ecdsa_521_key.pub

Adding SSH public key from /etc/ssh/ssh_host_ecdsa_384_key.pub

Adding SSH public key from /etc/ssh/ssh_host_rsa_key.pub

Adding SSH public key from /etc/ssh/ssh_host_ed25519_key.pub

Adding SSH public key from /etc/ssh/ssh_host_ecdsa_key.pub

[try 1]: Forwarding 'host_mod' to json server

'https://idmns.linuxsysadmins.local/ipa/session/json'

Could not update DNS SSHFP records.

SSSD enabled

Configured /etc/openldap/ldap.conf

Configured /etc/ssh/ssh_config

Configured /etc/ssh/sshd_config

Configuring linuxsysadmins.local as NIS domain.

Client configuration complete.

The ipa-client-install command was successful

Authenticating REST Requests

ESC REST and ETSI REST APIs use http basic access authentication where the ESC client will have to provide a username and password when making REST requests. The user name and password will be encoded with Base64 in transit, but not encrypted or hashed. HTTPS will be used in conjunction with Basic

Authentication to provide the encryption.

This section discusses ESC REST and ETSI REST authentications, how to change the default password of the interfaces, and how to send an authorized requests from the ESC client.

REST Authentication

By default, the REST authentication is enabled. To disable REST authentication, you can pass the argument

--disable-rest-auth to bootvm. Cisco does not recommend you to use this in a production environment.

ESC also supports https communication over port 8443. ESC will generate a self-signed certificate that the client will need to trust to get the https communication going. By default, REST is enabled as HTTP and restricted to localhost.

ESC can be installed with external access to REST on HTTPS or HTTP enabled with additional bootvm.py

arguments: -enable-https-rest or --enable-http-rest .

It is recommended to use only enabled external REST API when required. When enabled, it is recommended to use bootvm.py --enable-https-rest --user_rest_pass USERNAME:PASSWORD .

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

117

Post Installation Tasks

Enabling ETSI REST Authentication

Note Make sure to pass either --enable-https-rest or --enable-http-etsi-rest or both the arguments to the bootvm.py

script to enable http and https interfaces to the REST API. You must pass --user_rest_pass while using either

--enable-https-rest or --enable-http-etsi-rest when REST authentication is not disabled. To enable https or http after ESC VM is booted, use the escadm command specified below.

sudo escadm escmanager set --url http://127.0.0.1:8080/ESCManager,https://0.0.0.0:8443/ESCManager

You must change the configuration of the peer instance if ESC is in HA Active/Standby mode.

Enabling ETSI REST Authentication

If the ETSI REST http or https interfaces are enabled, then all requests to an ETSI API must contain authentication data. You can use the --enable-http-etsi-rest or --enable-https-etsi arguments respectively to enable http and https interfaces to the ESC bootvm.py installation script.

You can enable both interfaces simultaneously, but only the https interface should be enabled in a production environment.

Note To enable http or https after the ESC VM has booted, use the escadm command specified below: sudo escadm etsi enable_http_rest

OR sudo escadm etsi enable_https_rest

Then restart the ETSI service.

Changing the REST Interface Password

The REST interface has only one default username/password (admin/<default_password>). The password can be updated after the bootup using escadm tool from the ESC VM CLI. You can also update the password through the REST API.

Procedure

Step 1

Step 2

To replace the existing password with a new one, use one of the below options:

• Using the escadm tool from the ESC VM CLI, you can generate a random password:

[root@test-v44-52 admin]# escadm rest set --help usage: escadm rest set [-h] [-v] --username USERNAME [--password PASSWORD] optional arguments:

-h, --help show this help message and exit

-v, --v, --verbose show verbose output

--username USERNAME

--password PASSWORD new password or use randomly generated password if no password provided

118

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Post Installation Tasks

Changing the ETSI REST Interface Password

• Using the REST API: http://[ESCVM_IP]:8080/ESCManager/v0/authentication/setpassword?userName=admin&password=yourPassword or https://[ESCVM_IP]:8443/ESCManager/v0/authentication/setpassword?userName=admin&password=yourPassword

Changing the ETSI REST Interface Password

The ETSI REST interface has only one default username/password (admin/<default_password>). The password can be updated after the bootup using escadm tool from the ESC VM CLI.

Procedure

Step 1

Step 2

To set the default ETSI REST username and password, use the following command: sudo escadm etsi set --rest_user username:password or

[admin@xyz-esc-4-4-0-59-keep ~]$ escadm etsi set --help usage: escadm etsi set [-h] [-v] [--startup {0,1,true,false,manual,auto}]

[--rest_user REST_USER] [--pam_service PAM_SERVICE] optional arguments:

-h, --help show this help message and exit

-v, --v, --verbose show verbose output

--startup {0,1,true,false,manual,auto} set to false|0|manual to disable etsi at startup.

--rest_user REST_USER

Set the user for rest. Format username:password

--pam_service PAM_SERVICE

Specify a PAM service to use for authentication. This will override the rest user. To revert to the using the rest user for authentication, supply an empty string.

Sending an Authorized REST Request

To send an authorized request, the ESC client should send the request with the following header:

Authorization: Basic YWRtaW46Y2lzY28xMjM= where YWRtaW46Y2lzY28xMjM= is the Base64 encoded string of the default username/password.

Most libraries and web clients have an interface for providing the username/password and the application will encode the username/password and add the HTTP Basic Auth header.

Example using the default credentials:

For HTTP: http://[ESCVM_IP]:8080/ESCManager/v0/tenants/

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

119

Post Installation Tasks

Sending an Authorized ETSI REST Request

For HTTPS: https://[ESCVM_IP]:8443/ESCManager/v0/tenants/

Sending an Authorized ETSI REST Request

To send an authorized request, the ESC client should send the request with the following header:

Authorization: Basic YWRtaW46Y2lzY28xMjM= where YWRtaW46Y2lzY28xMjM= is the Base64 encoded string of the default username/password.

Most libraries and web clients have an interface for providing the username/password and the application will encode the username/password and add the HTTP Basic Auth header.

Example using the default credentials:

For HTTP: http://[ESCVM_IP]:8250/vnflcm/v1/vnf_lcm_op_occs

For HTTPS: http://[ESCVM_IP]:8251/vnflcm/v1/vnf_lcm_op_occs

Configuring Openstack Credentials

If ESC was deployed without passing VIM credentials, you can set VIM credentials through ESC VIM and through VIM User APIs (REST or Netconf API ).

Note ESC will accept the northbound configuration request only if the following conditions are met:

• ESC has VIM or a VIM user configured through APIs(REST/Netconf).

• ESC has VIM or a VIM user configured, and ESC is able to reach the VIM.

• ESC has VIM or a VIM user configured, and ESC is able to authenticate the user.

Configuring using Netconf API

• Passing VIM credential using Netconf :

<esc_system_config xmlns="http://www.cisco.com/esc/esc">

<vim_connectors>

<vim_connector>

<id>my-server-30</id>

<type>OPENSTACK</type>

120

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Post Installation Tasks

Configuring Openstack Credentials

</property>

<name>os_project_name</name>

<value>vimProject</value>

</property>

<name>os_project_domain_name</name>

<value>default</value>

</property>

</properties>

<users>

<user>

<id>admin</id>

<name>os_password</name>

</property>

<name>os_user_domain_name</name>

<value>default</value>

</property>

</properties>

</credentials>

</user>

</users>

</vim_connector>

</vim_connectors>

</esc_system_config>

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

121

Post Installation Tasks

Configuring Openstack Credentials

Note • From ESC 3.0 onwards, multiple VIM connectors are supported but within one ESC, only one type of VIM are supported. For example, all the Vim

Connector(s) has to be for OpenStack only. One ESC VIM cannot have two

VIM connector, one points to OpenStack, one points to VMware.

• One VIM is chosen as the default VIM which supports all pre 3.0 config requests and datamodels.

• Deployments can be done on the VIM that is not the default VIM. The deployment to a non default VIM has to have all out-of-band resources

(except ephemeral volumes). No other configurations like image, flavor, network, and so on can be done on the VIM that is not the default VIM.

• The default VIM connector will be auto provisioned and does not need to be configured in the following scenarios:

• If VIM credentials have been passed during ESC boot up.

• If upgrading from 2.3.x to 3.0.

• The change in the datamodel for Openstack create VIM connector would be handled during upgrade by migration. The 'os_tenant_name' and

'os_project_domain_name' properties would be moved to the VIM Connector properties and 'os_ternant_name' will be renamed to 'os_project_name'.

• For the default VIM Connector, once it is properly authenticated, its properties cannot be updated.

• VIM user can be deleted, recreated, or its properties can be updated at anytime.

• Updating VIM Connector using Netconf:

<esc_system_config xmlns="http://www.cisco.com/esc/esc">

<vim_connectors>

<vim_connector nc:operation="replace">

<id>example_vim</id>

<type>OPENSTACK</type>

</property>

<name>os_project_name</name>

<value>vimProject</value>

</property>

<name>os_project_domain_name</name>

<value>default</value>

</property>

<name>os_identity_api_version</name>

122

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Post Installation Tasks

Configuring Openstack Credentials

</property>

</properties>

</vim_connector>

</vim_connectors>

</esc_system_config>

• Updating VIM user using Netconf:

<esc_system_config xmlns="http://www.cisco.com/esc/esc">

<vim_connectors>

<vim_connector>

<id>example_vim</id>

<users>

<name>os_password</name>

</property>

<!-- The user domain name is only needed for openstack v3 identity api

-->

<name>os_user_domain_name</name>

<value>default</value>

</property>

</properties>

</credentials>

</user>

</users>

</vim_connector>

</vim_connectors>

</esc_system_config>

• Deleting VIM connector using Netconf:

<esc_system_config xmlns="http://www.cisco.com/esc/esc"> <vim_connectors>

<vim_connector nc:operation="delete">

<id>example_vim</id>

</vim_connector>

</vim_connectors>

</esc_system_config>

• Deleting VIM Connector using command:

$ esc_nc_cli --user <username> --password <password> delete-vim-connector <vim connector id>

• Deleting VIM user using command:

$ esc_nc_cli --user <username> --password <password> delete-vim-user <vim connector id>

Configuring using REST API

• Adding VIM using REST:

POST /ESCManager/v0/vims/

HEADER: content-type, callback

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

123

Post Installation Tasks

Configuring Openstack Credentials

<?xml version="1.0"?>

<vim_connector xmlns="urn:ietf:params:xml:ns:netconf:base:1.0">

<id>example_vim</id>

<type>OPENSTACK</type>

</property>

<name>os_project_name</name>

<value>vimProject</value>

</property>

<name>os_project_domain_name</name>

<value>default</value>

</property>

<name>os_identity_api_version</name>

</property>

</properties>

</vim_connector>

• Adding VIM user using REST:

POST /ESCManager/v0/vims/{vim_id}/vim_users

HEADER: content-type, callback

<?xml version="1.0"?>

<name>os_password</name>

</property>

<name>os_user_domain_name</name>

<value>default</value>

</property>

</properties>

</credentials>

</user>

• Update VIM using REST:

PUT /ESCManager/v0/vims/{vim_id}

HEADER: content-type, callback

<?xml version="1.0"?>

<vim_connector xmlns="urn:ietf:params:xml:ns:netconf:base:1.0">

<id>example_vim</id>

<type>OPENSTACK</type>

</property>

124

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Post Installation Tasks

Configuring Openstack Credentials

<name>os_project_name</name>

<value>vimProject</value>

</property>

<name>os_project_domain_name</name>

<value>default</value>

</property>

<name>os_identity_api_version</name>

</property>

</properties>

</vim_connector>

• Update VIM user using REST:

PUT /ESCManager/v0/vims/{vim_id}/vim_users/{vim_user_id}

HEADER: content-type, callback

<?xml version="1.0"?>

<name>os_password</name>

</property>

<name>os_user_domain_name</name>

<value>default</value>

</property>

</properties>

</credentials>

</user>

• Delete VIM using REST:

DELETE /ESCManager/v0/vims/{vim_id}

• Delete VIM user using REST:

DELETE /ESCManager/v0/vims/{vim_id}/vim_users/{user_id}

• Notification example after each VIM or VIM user configuration is complete:

<?xml version="1.0" encoding="UTF-8"?>

<status>SUCCESS</status>

<status_code>200</status_code>

<status_message>Created vim connector successfully</status_message>

<vim_connector_id>my-server-30</vim_connector_id>

<event>

<type>CREATE_VIM_CONNECTOR</type>

</event>

</escEvent>

</notification>

Important Notes:

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

125

Post Installation Tasks

Enabling Barbican Client in ESC

• In ESC 3.0, you can add multiple VIM Connector for Openstack VIM. Each VIM Connector can have only one VIM User.

• VIM username and password can be updated at anytime. VIM endpoint will not be able to update after a resource is created through ESC.

• After VIM is connected and VIM user is authenticated, VIM can no longer be deleted or updated, only VIM user can be deleted or updated.

• The name of a VIM property or VIM user credentials property is not case sensitive, e.g.

OS_AUTH_URL and os_auth_url is the same to ESC.

Enabling Barbican Client in ESC

OpenStack Barbican provides secure storage, provisioning, and management of secret, for example, passwords, encryption keys, and X.509 Certificates.

Enable the Barbican client to manage the secret used to encrypt an OpenStack volume before mounting it on a VM. You can access the OpenStack Barbican APIs through a Python 3 environment. The OpenStack Barbican client python-barbicanclient 5.0.1 is integrated in the ESC.

Enable the virtual environment by using the following command: source /opt/esc_custom_python3_venv/bin/activate

Reconfiguring ESC Virtual Machine

This section covers the following:

• Reconfiguring Rsyslog

• Reconfiguring NTP

• Reconfiguring DNS

• Reconfiguring Hosts

• Reconfiguring Timezone

Reconfiguring Rsyslog

Rsyslog parameters are optional. If there is a need for customization after booting an ESC VM, you can edit the files in ESC VM (/etc/rsyslog.d/).

Procedure

Step 1 Editing the Rsyslog file :

• If you haven't specified the log forwarding configuration at the bootup time, you may create a file under

/etc/rsyslog.d/ like /etc/rsyslog.d/log-forwarding.conf.

126

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Post Installation Tasks

Reconfiguring Rsyslog

• If you have specified the log forwarding through installation, you may just need to edit the file. The file could be /etc/rsyslog.d/20-cloud-config.conf. In this file, to forward logs to multiple rsyslog servers, edit the following line:

*.* @[server_ip]:port

Note • Use '@@' before specifying server ip address (if TCP is the protocol used to forward logs to the rsyslog server).

• Use '@' before specifying server ip address (if UDP is the protocol used to forward logs to the rsyslog server).

• server_ip can either be ipv4/ipv6 address of the rsyslog server.

• '[ ]' around the server_ip is required to separate it from ' :port# ', if an ipv6 server address is specified.

Step 2

Step 3

Step 4

For further information on Rsyslog configuration, see the Red Hat documentation.

Configuring the ESC log file: Configure which ESC log files you want to forward to the rsyslog server: a) Navigate to /etc/rsyslog.d/ Create or modify a configuration file, such as log-esc.conf

. Make a copy of sample log-esc.conf .

b) Specify the following block for every file you want to forward to rsyslog server.

$InputFileName /var/log/esc/escmanager.log

$InputFileTag esc-manager:

$InputFileStateFile stat-esc-manager

$InputFileSeverity info

$InputRunFileMonitor

For example:

$InputFileName /var/log/esc/file1.log

$InputFileTag file1:

$InputFileStateFile stat-file1

$InputFileSeverity info

$InputRunFileMonitor

$InputFileName /var/log/esc/file2.log

$InputFileTag file2:

$InputFileStateFile stat-file2

$InputFileSeverity info

$InputRunFileMonitor

Restart the rsyslog service

# service rsyslog restart

Configure the server side to receive forwarded logs.

a) On a designated server, go to /etc/rsyslog.conf, and uncomment the lines shown below, depending on if you want to listen to logs from clients based on TCP or UDP:

#$ModLoad imudp

#$UDPServerRun 514 b) Exit the file. Run this command as the last step.

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

127

Post Installation Tasks

Reconfiguring NTP sudo service rsyslog restart

Now, the server is listening for logs on port 514, using TCP/UDP.

Reconfiguring NTP

Procedure

Step 1

Step 2

Step 3

Step 4

Step 5

Open the NTP configuration file /etc/ntp.conf in a text editor such as vi, or create a new one if it does not already exist:

# vi /etc/ntp.conf

Add or edit the list of public NTP servers. If you don't specify the NTP server through the installation, the file should contain the following default lines, but feel free to change or expand these according to your needs: server 0.rhel.pool.ntp.org iburst server 1.rhel.pool.ntp.org iburst server 2.rhel.pool.ntp.org iburst server 3.rhel.pool.ntp.org iburst server <your_ntp_server_ip> iburst

The iburst directive at the end of each line speeds up the initial synchronization.

Once you have the list of servers complete, in the same file, set the proper permissions, giving the unrestricted access to localhost only. Make sure those lines are there in your configure file.

restrict default kod nomodify notrap nopeer noquery restrict -6 default kod nomodify notrap nopeer noquery restrict 127.0.0.1

restrict -6 ::1

Save all changes, exit the editor, and restart the NTP daemon:

# service ntpd restart

Make sure that ntpd is started at boot time:

# chkconfig ntpd on

Reconfiguring DNS

Procedure

Step 1 The /etc/resolv.conf file contains the configuration for the DNS client (resolver). It typically looks something like this: search domain.com

nameserver 8.8.4.4

This results in a

/etc/resolv.conf

128

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Post Installation Tasks

Reconfiguring Hosts

Step 2

Step 3

Created by cloud-init on instance boot automatically, do not edit.

;

#Generated by esc-cloud domain cisco.com

search cisco.com

nameserver 8.8.4.4

Note It is recommended that you ignore the do not edit message, if you want to modify the file.

You may modify the IP address of the "nameserver" item or add new nameserver records.

search domain.com

nameserver <your_first_dns_ip> nameserver <your_second_dns_ip>

Restart Network Service.

service network restart

Reconfiguring Hosts

The /etc/hosts file allows you to add, edit, or remove hosts . This file contains IP addresses and their corresponding hostnames. If your network contains computers whose IP addresses are not listed in DNS, it is recommended that you add them to the /etc/hosts file.

Procedure

Step 1

Step 2

Add the IP addresses that are not listed in DNS to the /etc/hosts file.

Restart your network for the changes to take effect.

service network restart

Reconfiguring Timezone

For ESC VM, in /etc the file "localtime" is a link to or copy of a file containing information about your time zone. Access your zone information files from /usr/share/zoneinfo. To change the time zone, find your country, your city or a city in the same time zone from zone information files in /usr/share/zoneinfo and link it to the localtime in the /etc file.

$ ln \-sf /usr/share/zoneinfo/America/Los_Angeles /etc/localtime

Verifying ESC Configurations and Other Post-Install Operations

This section covers various post-install checks and operations using the escadm tool.

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

129

Post Installation Tasks

Verifying ESC Configurations and Other Post-Install Operations

Verifying Existing ESC Configurations

You can use escadm dump command for displaying current ESC configurations in yaml format. The output will show the various services in ESC.

$ sudo escadm dump resources: confd: init_aaa_users:

- name: admin passwd: option: start-phase0 esc_service: group:

- confd

- mona

- vimmanager

- pgsql

- escmanager

- portal

- monitor

- snmp type: group escmanager: {} mona: {} monitor: {} pgsql: {} portal: {} snmp: run_forever: true vimmanager: {}

Verifying VIM configurations

You can use escadm vim show command to verify the vim settings are correctly populated:

$ sudo escadm vim show

[

{

"status": "CONNECTION_SUCCESSFUL",

"status_message": "Successfully connected to VIM",

"type": "OPENSTACK",

"id": "default_openstack_vim",

"properties": {

"property": [

{

"name": "os_auth_url",

"value": "http://172.16.103.143:35357/v3"

}

]

}

]

Troubleshooting ESC Services Startup Issues

Problem : Issues encountered while verifying ESC services status at the installation time using sudo escadm status

130

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Post Installation Tasks

Verifying ESC Configurations and Other Post-Install Operations

Causes : Some services take time to start or have trouble starting.

Solution :

Identify the issues using one of the following method:

• Check the log /var/log/esc/escadm.log

$ cat /var/log/esc/escadm.log

2017-06-01 20:35:02,925: escadm.py(2565): INFO: promote drbd to primary...

2017-06-01 20:35:02,934: escadm.py(2605): INFO: Waiting for at least one drbd to be

UptoDate...

2017-06-01 20:35:02,942: escadm.py(2616): INFO: Waiting for peer drbd node to be demoted...

2017-06-01 20:35:14,008: escadm.py(2423): INFO: mount: /dev/drbd1

/opt/cisco/esc/esc_database

2017-06-01 20:35:14,017: escadm.py(1755): INFO: Starting filesystem service: [OK]

2017-06-01 20:35:15,039: escadm.py(1755): INFO: Starting vimmanager service: [OK]

2017-06-01 20:35:16,116: escadm.py(1755): INFO: Starting monitor service: [OK]

2017-06-01 20:35:17,163: escadm.py(1755): INFO: Starting mona service: [OK]

2017-06-01 20:35:18,440: escadm.py(1755): INFO: Starting snmp service: [OK]

2017-06-01 20:35:21,397: escadm.py(1770): INFO: Starting confd service:[FAILED]

2017-06-01 20:35:28,304: escadm.py(1755): INFO: Starting pgsql service: [OK]

2017-06-01 20:35:29,331: escadm.py(1755): INFO: Starting escmanager service: [OK]

2017-06-01 20:35:30,354: escadm.py(1755): INFO: Starting portal service: [OK]

2017-06-01 20:35:31,523: escadm.py(1755): INFO: Starting esc_service service: [OK]

• Add '-v' to escadm status to show the verbose output of the ESC services.

$ sudo escadm status --v

0 ESC status=0 ESC HA Active Healthy pgsql (pgid 61397) is running vimmanager (pgid 61138) is running monitor (pgid 61162) is running mona (pgid 61190) is running drbd is active snmp (pgid 61541) is running filesystem (pgid 0) is running

<<service>> is dead keepalived (pgid 60838) is running portal (pgid 61524) is running confd (pgid 61263) is running escmanager (pgid 61491) is running

Confirm the status of the identified services that has issues and manually start these services.

$ sudo escadm <<service>> status// If the status is stopped or dead, manually start the services using the next command.

$ sudo escadm <<service>> start --v

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

131

Post Installation Tasks

Logging in to the ESC Portal

Logging in to the ESC Portal

Note • The ESC portal is enabled by default. You must ensure that the ESC portal is not disabled during installation. For more information on enabling or disabling the ESC portal, see

Installing Cisco Elastic

Services Controller Using the QCOW Image, on page 8

• When you log in to the ESC portal for the first time you are prompted to change the default password.

To log in to the ESC portal, do the following:

Before you begin

• Register an instance of ESC. For more information on registering the ESC instance see,

Installing Cisco

Elastic Services Controller Using the QCOW Image, on page 8

• Ensure that you have the username and password.

Procedure

Step 1

Step 2

Step 3

Step 4

Step 5

Using your web browser, enter the IP address of ESC and port 443.

Example:

For example, if the IP address of ESC is 192.0.2.254, enter: https://192.0.2.254: 443 [ login via https]

A Security Alert message is displayed.

Click Yes to accept the security certificate. The Login page is displayed.

Enter the username and password and click Login .

If you are logging in for the first time, the login page reappears, prompting you to change your password.

Enter the old password in the Old Password field, then enter a new password in the New Password and Confirm

Password fields.

Click Update Password or press Enter .

132

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Post Installation Tasks

Logging in to the ESC Portal

Note • If the UI becomes unresponsive, restart the UI by executing the sudo escadm portal restart from the ESC shell prompt.

• ESC Portal only supports one user.

• Currently, a pre-installed self-signed certificate supports HTTPS. The user must confirm the self-signed certificate before proceeding with the ESC Portal.

• In HTTPS communication mode, if the URL protocol type returned by OpenStack is not

HTTPS, the access to the VNF Console may be disabled. For security reasons, while running in HTTPS more non-secure communication will be rejected.

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

133

Logging in to the ESC Portal

Post Installation Tasks

134

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

P A R T

VIII

Upgrading Cisco Elastic Services Controller

•

ESC in Maintenance Mode, on page 137

•

Upgrading Cisco Elastic Services Controller, on page 143

C H A P T E R

ESC in Maintenance Mode

This chapter contains the following chapters:

•

Setting ESC in a Maintenance Mode, on page 137

•

Backup the Database from the ESC Standalone Instances, on page 138

•

Backup the Database from the ESC HA Active/Standby Instances, on page 140

•

Restoring ESC Database, on page 141

Setting ESC in a Maintenance Mode

ESC must be put to maintenance mode to backup and restore ESC database. To do so, use the escadm tool as specified in the below section.

Before you begin

Note From ESC release 4.4, ESC continues to be in maintenance mode after HA Active/Standby switch over or

DB restoration, if ESC was in maintenance mode before HA Active/Standby switch over or DB restoration.

During maintenance mode,

• Northbound requests are blocked by ESC and ESC responds with maintenance mode notification.

• Only REST requests receive response that ESC is unavailable temporarily. ConfD requests get the maintenance mode rejection message, or an OK message for all idempotent request such as create tenant request when the tenant already exists.

• Monitoring actions are paused.

• All ongoing requests and transactions continue to progress.

Using the escadm Tool

ESC can be put to maintenance mode using the escadm tool.

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

137

Upgrading Cisco Elastic Services Controller

Setting ESC in an Operation Mode

Procedure

Step 1

Step 2

Step 3

Put ESC to maintenance mode from the VM shell: sudo escadm op_mode set --mode=maintenance

Set mode to MAINTENANCE

Operation Mode = MAINTENANCE

If you have D-MONA deployed, do the following to each D-MONA: curl -i -k --user {REST username}:{REST password} -X POST https:/{DMONA

IP}:8443/mona/v1/rules/pause_all

To query operation mode at any time, sudo escadm op_mode show

Example:

Operation Mode = OPERATION

Set maintenance mode when there is no in-flight transaction. Using the ipt_check flag with the escadm tool, you can choose to set ESC in the maintenance mode only if there are no ongoing transactions in ESC. Set the flag to true, if you do not want ESC to set in the maintenance mode, if there are ongoing transactions in ESC.

sudo escadm op_mode set --mode=maintenace --ipt_check=true

With the ipt_check option set to true, escadm tool checks if there is any on going operation, if so, the escadm tool will not set ESC to maintenance mode.

Note ESC with D-MONA deployment, requires to do extra calls when going to maintenance mode.

Setting ESC in an Operation Mode

Put ESC in operation mode using the escadm tool: sudo escadm op_mode set --mode=operation

Response is as follows:

Set mode to OPERATION

Operation Mode = OPERATION

If you have D-MONA deployed, do the following to each D-MONA: curl -i -k --user {REST username}:{REST password} -X POST https:/{DMONA

IP}:8443/mona/v1/rules/resume_all

Verify ESC's operation mode at any time using the following command: sudo escadm op_mode show

Backup the Database from the ESC Standalone Instances

• The following assumptions should be taken into consideration:

• A third machine is required to store the database and log backups.

138

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Upgrading Cisco Elastic Services Controller

Backup the Database from the ESC Standalone Instances

• ESC does not support database schema downgrade. Restoring database to the older ESC version could cause unexpected problems.

• Before you start the backup process, ensure you have an external storage space (could be in the OpenStack controller or any system accessible by ESC). The backup/restore could be expressed in a generic format which will be used by the escadm tool: scp://<username>:<password>@<backup_ip>:<filename> . In this format, the credentials, IP address and file storage path of the third machine are required. You may also use localhost IP as the backup IP to backup database in a location of ESC VM and then copy the files to the external storage

To backup the ESC database from a standalone ESC or a HA Active/Standby (active node):

Procedure

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Step 7

$ sudo escadm op_mode set --mode=maintenance

To make sure ESC is in maintenance mode, run:

$ sudo escadm op_mode show

Backup database. Execute the commands below as a root user:

# sudo escadm backup --file /tmp/db_file_name.tar.bz2

scp://<username>:<password>@<backup_vm_ip>:<filename>

To put ESC back to operation mode, run:

$ sudo escadm op_mode set --mode=operation

$ sudo escadm op_mode show

Collect all the logs from the old ESC VM and back it up. Execute the below command as a root user.

# sudo escadm log collect

A timestamped log file will be generated in: /var/tmp/esc_log <timestamp>.tar.bz2

Note If a dynamic mapping file is used by ESC service, the dynamic mapping file should be backed up at the same time with ESC logs. The default path of the dynamic mapping file is

/opt/cisco/esc/esc-dynamic-mapping/dynamic_mappings.xml.

After a successful database back-up, shut down the old ESC VM using Horizon/Kilo or Nova commands. For

ESC VM instances based in VMware vSphere, shutdown the active instance through VMware client dashboard.

An example of shutting down a VM in OpenStack is shown below :

$ nova stop OLD_ESC_ID

Detach the old port from the old VM and rename the old ESC node. Examples of detaching and renaming the

VM in OpenStack is shown below: nova interface-detach ESC_NAME port-id-of-ESC_NAME nova rename ESC_NAME ESC_NAME.old

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

139

Upgrading Cisco Elastic Services Controller

Backup the Database from the ESC HA Active/Standby Instances

In VMWare, assign a different IP address to the old VM and then rename the old VM.

BackuptheDatabase fromtheESCHAActive/Standby Instances

• The following assumptions should be taken into consideration:

• A third machine is required to store the database and log backups.

• ESC does not support database schema downgrade. Restoring database to the older ESC version could cause unexpected problems.

• Before you start the backup process, ensure you have an external storage space available (could be in the OpenStack controller or any system accessable by ESC). The backup/restore could be expressed in a generic format which will be used by the escadm tool: scp://<username>:<password>@<backup_ip>:<filename> . In this format, the credentials, IP address and file storage path of the third machine are required. You may also use localhost IP as the backup IP to backup database in a location of ESC VM and then copy the files to the external storage.

To backup the ESC database from a standalone ESC or a HA Active/Standby (active node):

Procedure

Step 1

Step 2

Perform the following steps on the Standby ESC node.

a) Connect to the standby ESC instance using SSH:

$ ssh <username>@<standby_vm_ip> b) Verify that the ESC instance is standby and note the name of the standby ESC HA Active/Standby instance:

$ sudo escadm status --v

If the output value shows "STANDBY", the node is the standby ESC node.

c) Change access to an admin user.

sudo bash d) Collect all the logs from the standby ESC VM and back it up.

$ sudo escadm log collect

A timestamped log file will be generated in: /var/tmp/esc_log <timestamp>.tar.bz2

e) Shutdown the standby ESC instance through OpenStack Kilo/Horizon using Nova command or VMware client. An example of shutting down the VM on OpenStack is shown below:

$ nova stop OLD_ESC_STANDBY_ID

Perform the following steps on the Active ESC node.

a) Connect to the active ESC instance using SSH:

$ ssh <username>@<active_vm_ip>

140

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Upgrading Cisco Elastic Services Controller

Restoring ESC Database

Step 3

Step 4 b) Change access to an admin user.

$ sudo bash c) Verify that the ESC instance is Active and note the name of the Active ESC HA Active/Standby instance

$ sudo escadm status --v

If the output value shows "ACTIVE", the node is the active ESC node.

d) Back up the database files from the active node of ESC HA Active/Standby:

$ sudo escadm backup --file /tmp/db_file_name.tar.bz2

scp://<username>:<password>@<standby_vm_ip>:<filename> e) Collect the logs from the active ESC VM and back it up.

$ sudo escadm log collect

A timestamped log file will be generated in: /var/tmp/esc_log <timestamp>.tar.bz2

Note If a dynamic mapping file is used by ESC service, the dynamic mapping file should be backed up at the same time with ESC logs. The default path of the dynamic mapping file is

/opt/cisco/esc/esc-dynamic-mapping/dynamic_mappings.xml

Shutdown the active ESC instance through OpenStack Kilo/Horizon using Nova command. For ESC VM instances based in VMware vSphere, shutdown the active instance through VMware client dashboard. An example of shutting down the VM on OpenStack is shown below:

$ nova stop OLD_ESC_ACTIVE

Use the nova list command or the nova show OLD_ESC_STANDBY command, to verify if the ESC HA

Active/Standby instances have been successfully shut down.

(Only for OpenStack) Detach the port from the old ESC VM and rename the old VM.

If upgraded ESC VM needs to operate with same IP addresses and same instance names as old instances, detach the ports from each instance, shutdown the old ESC VMs and then rename the old ESC instances.

If you intend to use old VMware active instance, assign a different IP address and rename the VM name. If not, you can delete the old VM and use the same IP address for the new upgraded VMware active instance.

After deleting the old VM, you can continue with the old instance name and the IP address.

OpenStack commands for detaching the ports and renaming the old VMs are shown below: nova interface-list ESC_NAME nova interface-detach ESC_NAME port-id-of-ESC_NAME nova rename ESC_NAME ESC_NAME.old

Restoring ESC Database

Before you begin

To restore the database,

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

141

Upgrading Cisco Elastic Services Controller

Restoring ESC Database

• In standalone ESC instance, stop ESC services. Run

# sudo escadm stop

• In HA Active/Standby type instances, stop escadm on the standby first, and later on the Active ESC HA

Active/Standby instance. Run

# sudo escadm stop

• All the services must be stopped. To check the status, run

# sudo escadm status --v

Procedure

Step 1

Step 2

Step 3

Restore the database. Execute the following command from the ESC VM:

$ scp <username>@<server_ip>:/path/db.tar.bz2

$ sudo escadm restore –file /tmp/db.tar.bz2

/tmp/

Enter the ESC password in the URL, or manually enter it after executing the above command.

Restart the ESC service to complete the database restore by running the following command:

$ sudo escadm restart

Note ESC maintenance mode blocks the northbound request and VNF monitoring. However, if there are some ongoing transactions because of northbound requests before ESC entering maintenance mode, those transactions may have following restriction with backup and restore:

• ESC reports an error for the deployment, network creation, and subnet creation requests, if these transactions are interrupted by backup and restore. Northbound handles these error messages but it may cause network or subnet leakage in some cases (For example, ESC is interrupted before getting the UUID from OpenStack).

• ESC reports an error for service chain upgrade, and requires service chain undeployment and deployment (rather than downgrade and upgrade) to re-create the service.

142

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

C H A P T E R

Upgrading Cisco Elastic Services Controller

Cisco Elastic Service Controller supports two type of upgrades:

• Backup and Restore Upgrade : This upgrade process involves stopping the ESC keepalive daemon (for

ESC HA), backing up the database, stopping and renaming (or deleting) the ESC instances, re-installing the ESC instances, and restore database. For information on the supported ESC versions for ESC 5.3

upgrade, see the table below.

• In-service upgrade : ESC supports in-service upgrade for Active/Standby high availability nodes with a minimum downtime.

You can upgrade the ESC instance as a standalone instance or as a high availability pair. The upgrade procedure is different for standalone and high availability pair.

This chapter lists separate procedures on how to upgrade ESC standalone and ESC High Availability instance.

You must review these instructions before you decide to upgrade the ESC instance. See the

Installation

Scenarios, on page 7

for more information on the installation scenarios.

• ESC only support direct upgrade from previous two major releases. For example, ESC 2.3 will support direct upgrade from ESC 2.1 and ESC 2.2. For any release older than the supported versions for direct upgrade, you need to perform the staged upgrade.

Note Example of an ESC major release, ESC 3.x, ESC 4.x,and ESC 5.x

Example of an ESC minor release, ESC 5.1.x and ESC 5.4.x

Example of an ESC maintenance release, ESC 5.4.0.x and 5.4.1.x;

Example of an ESC patch release, ESC 5.4.0.88, ESC 5.4.0.89, and ESC 5.4.0.100.

• Upgrading ESC using RPM Package (referred to as RPM Upgrade in this chapter) applies only to the

ESC upgrade between ESC patch releases with the same release number. For Example, the upgrade from

ESC 3.1.0.116 to ESC 3.1.0.150.

• If you want to upgrade ESC between minor releases (for example, upgrade from ESC 2.3.1 to ESC

2.3.2) or major releases (for example, upgrade from ESC 3.0 to ESC 4.0 ), you can upgrade through

Backup and Restore upgrade process using qcow2 image.

• For ESC upgrade, you should be familiar with ESC installation process.

• For OpenStack, refer to the OpenStack installation procedures, see Chapter 4: Installing Cisco Elastic

Services Controller in OpenStack.

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

143

Upgrading Cisco Elastic Services Controller

Upgrading Standalone ESC Instance

• For VMware, refer to the VMware Installation installation procedures, see Chapter 7: Installing

Cisco Elastic Services Controller in VMware vCenter.

• For ESC HA, please refer to the ESC HA installation procedures, see Chapter 5 : Configuring High

Availability for OpenStack and Chapter 8: Configuring High Availability for VMware.

Table 6: Supported ESC Versions for Upgrading to ESC 5.5

Virtual Infrastructure

Manager

OpenStack

VMware

CSP

Supported Versions for Backup and

Restore Upgrade

Supported Versions for In-Service Upgrade

5.4, 5.3

IMPORTANT NOTES

• After upgrading to the new ESC version, ESC service will manage the life cycle of all VNFs deployed in the previous release. To apply any new features (with new data models) to the existing VNFs, you must undeploy and redeploy these VNFs.

• Upgrade is supported for Active/Active HA only.

Note Do not change the VIP in ESC upgrade in ETSI deployment.

If you change ETSI's REST schema, from http to https in-flight, ESC stops sending recovery notification from

ESC core for any existing deployment.

•

Upgrading Standalone ESC Instance, on page 144

•

Upgrading ESC HA Active/Standby Instances, on page 146

•

In-Service Upgrade of the ESC HA Active/Standby Nodes in OpenStack, on page 148

•

In-Service Upgrade of ESC HA Active/Standby Nodes in Kernel-Based Virtual Machine (KVM), on page 152

•

In-Service Upgrade of the ESC HA Active/Standby Nodes in VMware, on page 156

•

In-Service Upgrade of the ESC HA Active/Standby Nodes in CSP, on page 160

Upgrading Standalone ESC Instance

To upgrade standalone ESC instance, perform the following tasks:

Back up the ESC database. For more information, see

Backup the Database from the ESC Standalone

Instances

Note To backup any custom scripts used by the deployments, and for restoring them before restoring the database, you must re-install the scripts on the backup as well.

144

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Upgrading Cisco Elastic Services Controller

Deploy the ESC for Upgrade

Redeploy the ESC instance. For more information, see the below section, Deploy the ESC for Upgrade .

Restore the ESC database on the new ESC instance. For more information, see the below section, Restoring the ESC Database .

Deploy the ESC for Upgrade

After backing up and shutting down of the old ESC VM, a new/upgraded (based on new ESC package) ESC

VM should be installed. All parameters for ESC installation should be the same as the old ESC VM deployment.

• For OpenStack, you need to register the new ESC qcow2 image using the Glance command with a new image name and then use new bootvm.py script and new image name to install ESC VM.

Note In OpenStack, if an old ESC VM was assigned with floating IP, the new ESC

VM should be associated with the same floating IP after the installation.

• For VMWare, you need to use the new ESC OVA file to install ESC VM. All other configurations and property values should be the same as the old VM.

Restoring the ESC Database

Restore the ESC database on the new ESC instance , using the following procedure:

Procedure

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Connect to the new ESC instance using SSH.

$ ssh USERNAME@NEW_ESC_IP

Stop the ESC service.

$ sudo escadm stop

Check ESC service status to make sure all the services are stopped.

$ sudo escadm status

Restore the database files.

$ scp://<username>:<password>@<standby_ip>:<filename>

$ sudo escadm restore --file /path/where/file/scp-ed/to/db.tar.bz2

Start the ESC service:

$ sudo escadm start

After ESC service is started, the standalone ESC upgrade is complete. You can check the health of the new

ESC service by running

$ sudo escadm status in the new ESC VM.

In Openstack, after restoring the database successfully, delete the old ESC instance:

$ nova delete OLD_ESC_ID

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

145

Upgrading Cisco Elastic Services Controller

Important Notes:

Important Notes:

After upgrading to the new ESC version, ESC service will keep doing life cycle management of all VNFs deployed by the old version. However, to apply any new features (with new data models) to the VNFs deployed by the ESC with old version is not guaranteed. If you want to apply any new feature of the new ESC version to existing VNFs, you have to undeploy and redeploy those VNFs.

Upgrading ESC HA Active/Standby Instances

To upgrade ESC HA Active/Standby nodes, perform the following tasks:

Back up the database from an old ESC HA Active/Standby active instance. For more information, see

Backup the Database from the ESC HA Active/Standby Instances .

Note To backup any custom scripts used by the deployments, and for restoring them before restoring the database, you must copy the scripts on the backup as well.

Deploy new ESC HA Active/Standby nodes based on new ESC version. For more information, see the below section, Deploy the ESC HA Active/Standby nodes for Upgrade .

Restore the database on active ESC instance (Standby ESC instance will sync with the active ESC instance

). For more information, see the below section, Restoring the ESC Database on New Active and Standby

Instances .

Deploying the ESC HA Active/Standby nodes for Upgrade

After backing up and shutting down the two old ESC VMs, based on new ESC package install the new ESC

VMs.

• For OpenStack, you need to register the new ESC qcow2 image using the Glance command with a new image name and then to use new bootvm.py script and new image name to install ESC VM. All other bootvm.py arguments should be the same as used to setup an old VMs.

• For VMWare, there are two steps to bring up HA Active/Standby pair in VMware: 1) setup two standalone instances 2) reconfigure each instance with HA Active/Standby info. All other configurations and property values should be the same as the old VMs.

• If VIP is used for Northbound access, keep VIP the same for the new deployment as used to reconfigure the old HA Active/Standby pair.

Restoring the ESC Database on New Active and Standby ESC Instances

Procedure

Step 1

Step 2

Shut down the Standby ESC instance .

Connect to the standby ESC instance using SSH.

$ ssh USERNAME@ESC_STANDBY_IP

Verify that the ESC instance is standby and note the name of the standby ESC HA Active/Standby instance

146

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Upgrading Cisco Elastic Services Controller

Restoring the ESC Database on New Active and Standby ESC Instances

Step 3

Step 4

Step 5

Step 6

Step 7

Step 8

Step 9

Step 10

Step 11

$ sudo escadm status

If the output value shows "STANDBY", the node is the standby ESC node.

Note If a dynamic mapping file (dynamic_mapping.xml) is used by ESC service, the dynamic mapping file should be restored into the standby ESC VM. Before power off the standby ESC node, you need to copy the backup dynamic mapping file (dynamic_mapping.xml) to the path

/opt/cisco/esc/esc-dynamic-mapping/ .

Shutdown the standby ESC instance through OpenStack Kilo/Horizon using Nova command. For ESC VM instances based in VMware vSphere, shutdown the active instance through VMware client dashboard. An example of shutting down the standby ESC instance in OpenStack is shown below:

$ nova stop NEW_ESC_STANDBY_ID

Restore the database on the new Active ESC instance.

Connect to the active ESC instance using SSH.

$ ssh USERNAME@ESC_ACTIVE_IP

Verify that the ESC instance is active.

$ sudo escadm status

If the output value shows 'ACTIVE' , the node is the active ESC node.

Stop the ESC services on the active node and verify the status to ensure the services are stopped.

$ sudo escadm stop

$ sudo escadm status

Restore the database files.

$ sudo escadm restore --file /tmp/db.tar.bz2

$ scp://<username>:<password>@<standby_ip>:<filename>

Note If a dynamic mapping file (dynamic_mapping.xml) is used by ESC service, the dynamic mapping file should be restored into the ESC VM. Before starting the ESC node, you need to copy the backup dynamic mapping file (dynamic_mapping.xml) to the path /opt/cisco/esc-dynamic-mapping/ .

Reboot the VM to restart the full ESC service:

$ sudo escadm restart

Use the

$ sudo escadm status to check the status of the ESC service.

Start the standby ESC node.

Power on the standby ESC node through OpenStack Nova/Horizon or VMware client. After starting the standby node, ESC HA Active/Standby upgrade process should be complete.

Delete the old HA Active/Standby instance through OpenStack Nova/Horizon or VMware client. An example of deleting the VM on OpenStack is shown below:

$ nova delete OLD_ESC_ACTIVE_RENAMED OLD_ESC_STANDBY_RENAMED

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

147

Upgrading Cisco Elastic Services Controller

Upgrading VNF Monitoring Rules

Upgrading VNF Monitoring Rules

To upgrade the VNF monitoring rules, you must back up the dynamic_mappings.xml

file and then restore the file in the upgraded ESC VM. For more information, see the backup and restore procedures. For upgrade of

HA Active/Standby instance, see

Upgrading ESC HA Active/Standby Instances

. For upgrade of the standalone instance, see

Upgrading Standalone ESC Instance

In-Service Upgrade of the ESC HA Active/Standby Nodes in

OpenStack

In-Service upgrade in OpenStack using ESC RPM packages

Procedure

Step 1

Step 2

Step 3

Step 4

Step 5

Backup ESC database and log files.

a) Perform ESC database backup from active node. For more information on backing up the database, see

Backup the Database from the ESC HA Active/Standby Instances .

b) Collect and backup all logs from both active and standby VMs. To backup the log, use the following command:

# sudo escadm log collect

Note A timestamped file will be generated in: /var/tmp/esc_log-<timestamp>.tar.bz2

c) Copy the database backup file and logs files (generated in /tmp/esc_log-.tar.bz2)* out of ESC VMs.

Log into the ESC HA Active/Standby standby VM and stop the escadm service.

$ sudo escadm stop

Ensure the ESC VM is in STOP state. ESC may take some time to switch to the STOP state. If ESC status turns into STOP state, please note that it won't be the part of HA Active/Standby cluster and you will lose

HA Active/Standby function temporarily.

$ sudo escadm status

Expected output:

ESC status=0 ESC HA is stopped

Copy the RPM file for upgrade to the ESC VM and execute the rpm command for upgrade.

$ sudo rpm -Uvh /home/admin/cisco-esc-3.1.0-145.x86_64.rpm

Start the escadm service.

$ sudo escadm start

148

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Upgrading Cisco Elastic Services Controller

In-Service upgrade in OpenStack using ESC qcow2 Image

Step 6

Step 7

Log into the ESC HA Active/Standby active VM and repeat step 2 to step 6 in active VM. Please note that after stop escadm service in active ESC VM, a failover will be triggered and the upgraded standby VM will take over the active role.

Check the ESC version on each instance to verify the version is upgraded correctly and make sure ESC service is running properly in new active VM.

# esc_version

# health.sh (in Active VM)

In-Service upgrade in OpenStack using ESC qcow2 Image

Procedure

Step 1

Step 2

Backup ESC database and log files.

a) Perform ESC database backup from active node. For more information on backing up the database, see

Backup the Database from the ESC HA Active/Standby Instances .

b) Collect and backup all logs from both active and standby VMs. To backup the log, use the following command:

# sudo escadm log collect

Note A timestamped file will be generated in: /var/tmp/esc_log-<timestamp>.tar.bz2

c) Copy the database backup file and logs files (generated in /tmp/esc_log-.tar.bz2)* out of ESC VMs.

Redeploy standby instance with the new version of ESC image, and wait for the data to be synchronized.

a) Delete the standby instance through Horizon Horizon Web UI or nova CLI. In OpenStack controller, running following command through nova client.

nova delete <secondary_vm_name> b) Register new ESC image into OpenStack Glance for redeployment usage.

glance image-create --name <image_name> --disk-format qcow2 --container-format bare

--file <esc_qcow2_file> c) Redeploy the standby ESC VM instance based on newer image version. Re-install the new standby instance by using the new ESC package (bootvm.py and new registered image). All other installation parameters should be the same as the former ESC VM deployment. For example, hostname, ip address, gateway_ip, ha_node_list, kad_vip, kad_vif have to use the same values. Once the new ESC instance with upgraded version is up, it will be in standby state.

d) Log into the new instance and run the following command to check the synchronization state of the new

ESC node.

$ drbdadm status

Wait until the output of drbdadm status show both nodes are "UpToDate" like the output below. It means the new ESC instance has completed the data synchronization from the active instance.

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

149

Upgrading Cisco Elastic Services Controller

In-Service upgrade in OpenStack using ESC qcow2 Image

Step 3

Step 4

Example for Active/Standby esc role:Secondary disk:UpToDate

101.1.0.119:7789 role:Primary peer-disk:UpToDate

Example for Active ESC esc role:Primary disk:UpToDate

101.1.0.120:7789 role:Secondary peer-disk:UpToDatee

Stop keepalived service on standby instance, Power off the active instance, and then start standby keepalived service.

a) To stop keepalived service, use the following command: escadm keepalived stop b) Log into the active instance, set ESC active node into maintenance mode.

$ sudo escadm op_mode set --mode=maintenance

Make sure there is no in-flight transaction ongoing before moving to the next step. To verify there are no in-flight transactions, use the following command:

For ESC 2.3:

$ sudo escadm ip_trans

For versions older than ESC 2.3, check escmanager log at (/var/log/esc/escmanager.log) and make sure there are no new transaction in escmanager log.

c) Log in to the upgraded standby instance and shut down the ESC service.

$ sudo escadm stop d) Power off the active instance through OpenStack Nova client/Horizon and make sure it is off. In OpenStack

Controller, run:

$ nova stop <active_vm_name>

$ nova list | grep <active_vm_name> e) Log into the previously upgraded standby instance which is in stopped state and restart the ESC service.

The standby ESC instance will take the active role (switchover will be triggered) and start providing services with new version.

$ sudo escadm start

Check the ESC version on the new active instance to verify the version is upgraded correctly.

$ sudo escadm status (check ha status)

Expected output:

0 ESC status=0 ESC HA Active Healthy

$ esc_version (check esc version) version : 3.x.x

150

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Upgrading Cisco Elastic Services Controller

In-Service upgrade in OpenStack using ESC qcow2 Image

Step 5

Step 6 release : xxx

Re-deploy the old active instance with the new ESC image.

Delete the old active instance and redeploy it by using the new ESC package (bootvm.py and new registered image).

a) Log in to the new deployed instance and check ha status. The new instance should be in standby state:

$ sudo escadm status --v b) Run the following command to check the synchronization state of the new ESC standby node:

$ drbdadm status

Wait until the output of drbdadm status shown as UpToDate.

c) For the new ESC standby node, make sure the health check is passed and the ESC version are upgraded correctly.

$ sudo escadm status (check ha status)

Expected output:

0 ESC status=0 ESC HA Standby Healthy

$ esc_version (check esc version)version : 2.x.x

release : xxx

$ health.sh

Expected output:

ESC HEALTH PASSED

Go back in to the first upgraded active instance and check the health and keepalived state.

$ drbdadm status

Expected output:

1:esc/0 Connected Primary/Secondary UpToDate/UpToDate /opt/cisco/esc/esc_database ext4

2.9G 52M 2.7G 2%

$ sudo escadm status (check ha status)

Expected output:

0 ESC status=0 ESC HA Active Healthy

$ esc_version (check esc version) Expected output: version : 2.x.x

release : xxx

$ health.sh (check esc health)

Expected output:

ESC HEALTH PASSED

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

151

Upgrading Cisco Elastic Services Controller

In-Service Upgrade of ESC HA Active/Standby Nodes in Kernel-Based Virtual Machine (KVM)

Note Quick rollback: In case of an upgrade failure, shutdown the upgraded instance and start the old active instance to have a quick rollback.

Rollback Procedure for In-service Upgrade a.

Copy the database and log backup files to a location out of ESC VMs.

Delete any remaining ESC instance and redeploy ESC HA Active/Standby VMs using qcow2 image with old version.

Restore the database. Follow the procedures in the section, Upgrading ESC HA Active/Standby

Instance with Backup and Restore for HA Active/Standby database restore.

After database restore, you should have ESC service back with the old version.

In-Service Upgrade of ESC HA Active/Standby Nodes in

Kernel-Based Virtual Machine (KVM)

In-Service Upgrade in KVM using ESC RPM packages

Use this procedure to upgrade ESC high-availability nodes with a minimum service interruption on a

Kernel-based virtual machine.

Procedure

Step 1

Step 2

Step 3

Step 4

Step 5

Backup ESC database and log files.

a) Perform ESC database backup from active node. For more information on backing up the database, see

Backup the Database from the ESC HA Active/Standby Instances .

b) Collect and backup all logs from both active and standby VMs. To backup the log, use the following command:

$ sudo escadm log collect

Note A timestamped log file will be generated in: /var/tmp/esc_log-<timestamp>.tar.bz2

c) Copy the database backup file and logs files (generated in /tmp/esc_log-.tar.bz2)* out of ESC VMs.

Log into the ESC HA Active/Standby standby VM and stop the ESC service.

$ sudo escadm stop

Make sure the standby ESC VM is in STOP state.

$ sudo escadm status --v

If ESC status=0 esc ha is stopped.

In standby VM, execute the rpm command for upgrade:

$ sudo rpm -Uvh /home/admin/cisco-esc-<latest rpm filename>.rpm

Log into the active instance, set ESC active node into maintenance mode.

$ sudo escadm op_mode set --mode=maintenance

152

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Upgrading Cisco Elastic Services Controller

In-Service Upgrade in KVM using ESC OVA Image

Step 6

Step 7

Step 8

Step 9

Step 10

Make sure there are no in-flight transactions and no new transactions during the upgrade. Use following commands to check in-flight transactions.

$ sudo escadm ip_trans

For any build older than ESC 2.3, you may need to check escmanager log for transactions at

(/var/log/esc/escmanager.log).

Power off ESC active node and make sure it is completely shut down. In KVM ESC controller, execute the following commands:

$ virsh destroy <active_vm_name>

$ virsh list --all

Log in the upgraded ESC instance (previous standby one), start the ESC service. The upgraded VM will take over active role and provide ESC service.

$ sudo escadm restart

$ sudo escadm monitor start

Check the ESC version on the new active instance to verify the upgraded version is correct. Once it is in the active state, make sure ESC service is running properly in the new active VM.

$ sudo escadm status

Expected output:

0 ESC status=0 ESC HA Active Healthy

$ esc_version

$ health.sh

Expected output:

ESC HEALTH PASSED

Power on the old active instance. In KVM ESC controller, execute the following commands:

$ virsh start <active_vm_name>

Log into the VM which is still with old ESC version and repeat step 2, 3, 4, and 7 in the VM.

In-Service Upgrade in KVM using ESC OVA Image

Procedure

Step 1 Backup ESC database and log files.

a) Perform ESC database backup from active node. For more information on backing up the database, see

Backup the Database from the ESC HA Active/Standby Instances .

b) Collect and backup all logs from both active and standby VMs. To backup the log, use the following command:

$ sudo escadm log collect

Note A timestamped log file will be generated in: /var/tmp/esc_log-<timestamp>.tar.bz2

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

153

Upgrading Cisco Elastic Services Controller

In-Service Upgrade in KVM using ESC OVA Image

Step 2

Step 3

Step 4 c) Copy the database backup file and logs files (generated in /tmp/esc_log-.tar.bz2)* out of ESC VMs.

Redeploy standby ESC instance. Register new ESC image on the standby instance.

a) Delete the standby instance through lib vert Virsh commands. On KVM host, run the following command:

$ Virsh destroy the <secondary_vm_name>

$ Virsh undefine --remove-all-storage <secondary_vm_name> b) Copy the new ESC image into Kvm Host for redeployment usage: sshpass -p "host Password' scp /scratch/BUILD-2_x_x_x/BUILD-2_x_x_x/ESC-2_x_x_x.qcow2

root@HOSTIP: c) Redeploy the standby ESC VM instance based on newer image version. Re-install new the standby instance by using the new ESC package (bootvm.py and new registered image). All other installation parameters should be the same as the former ESC VM deployment. For example, hostname, ip address, gateway_ip, ha_node_list, kad_vip, kad_vif have to use the same values. Once the new ESC instance with upgraded version is up, it will be in standby state.

d) Log into the new instance and run the following command to check the synchronization state of the new

ESC node.

$ drbdadm status wait until the output of drbdadm status show both nodes are "UpToDate" like the output below. It means the new ESC instance has completed the data synchronization from the active instance.

esc/0 Connected Secondary/Primary UpToDate/UpToDate

Stop keepalived service on standby instance, Power off active instance, and then start standby keepalived service.

a) Log into the active instance, set ESC active node into maintenance mode.

$ sudo escadm op_mode set --mode=maintenance

Make sure there is no in-flight transaction ongoing before moving to the next step. To verify there are no in-flight transactions, use the following command:

$ sudo escadm ip_trans

Check escmanager log at (/var/log/esc/escmanager.log) and make sure there are no new transaction in escmanager log.

b) Log in to the upgraded standby instance and shut down the keepalived service.

$ sudo escadm stop c) Power off the active instance and make sure it has been completely turned off. In KVM ESC Controller, run:

$ virsh destroy <active_vm_name>

$ virsh list --all d) Log into the previously upgraded standby instance which is in stopped state and start the ESC service.

The standby ESC instance will take the active role (switchover will be triggered) and start providing services with new version.

$ sudo escadm restart

Check the ESC version on the new active instance to verify the version is upgraded correctly.

154

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Upgrading Cisco Elastic Services Controller

In-Service Upgrade in KVM using ESC OVA Image

Step 5

Step 6

$ sudo escadm status (check ha status)

Expected output:

0 ESC status=0 ESC HA Active Healthy

$ esc_version (check esc version) version : 4.1.x

release : xxx

$ health.sh (check esc health)

Expected output:

ESC HEALTH PASSED

Re-deploy the old active instance with the new ESC image.

a) Log in to the new deployed instance and check ha status. The new instance should be in standby state:

$ sudo escadm status b) Run the following command to check the synchronization state of the new ESC standby node:

$ drbdadm status

Wait until the output of drbdadm status shown as UpToDate.

c) For the new ESC standby node, make sure the health check is passed and the ESC version are upgraded correctly.

$ sudo escadm status (check ha status)

Expected output:

0 ESC status=0 ESC HA Active Healthy

$ esc_version (check esc version)version : 4.1.x

release : xxx

$ health.sh

Expected output:

ESC HEALTH PASSED

Go back in to the first upgraded active instance and check the health and keepalived state.

$ drbdadm status

Expected output:

1:esc/0 Connected Primary/Secondary UpToDate/UpToDate /opt/cisco/esc/esc_database ext4

2.9G 52M 2.7G 2%

$ sudo escadm status (check ha status)

Expected output:

0 ESC status=0 ESC HA Active Healthy

$ esc_version (check esc version) Expected output: version : 2.x.x

release : xxx

$ health.sh (check esc health)

Expected output:

ESC HEALTH PASSED

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

155

Upgrading Cisco Elastic Services Controller

In-Service Upgrade of the ESC HA Active/Standby Nodes in VMware

Note Quick rollback: In case of an upgrade failure, shutdown the upgraded instance and start the old active instance to have a quick rollback.

Rollback Procedure for In-service Upgrade a.

Delete any remaining ESC instance and redeploy ESC HA Active/Standby VMs using qcow2 image with old version.

Restore the database. Follow the procedures in the section, Upgrading ESC HA Active/Standby

Instance with Backup and Restore for HA Active/Standby database restore.

After database restore, you should have ESC service back with the old version.

In-Service Upgrade of the ESC HA Active/Standby Nodes in

VMware

In-Service upgrade in VMware using ESC RPM packages

Use this procedure to upgrade the ESC high-availability nodes one node at a time with a minimum service interruption. This process leverages the ESC HA Active/Standby replication and failover capability to smoothly move ESC service to the new upgraded node without the manual database restore.

Procedure

Step 1

Step 2

Step 3

Step 4

Step 5

Backup ESC database and log files.

a) Perform ESC database backup from active node. For more information on backing up the database, see

Backup the Database from the ESC HA Active/Standby Instances .

b) Collect and backup all logs from both active and standby VMs. To backup the log, use the following command:

# sudo escadm log collect c) Copy the database backup file and logs files (generated in /tmp/esc_log-.tar.bz2)* out of ESC VMs.

Log into the ESC HA Active/Standby standby VM and stop the keepalived service.

$ sudo escadm stop

Make sure the standby ESC VM is in STOP state.

$ sudo escadm status --v

If ESC status=0 esc ha is stopped.

In the standby VM, execute the rpm command for upgrade:

$ sudo rpm -Uvh /home/admin/cisco-esc-2.2.9-50.rpm

Log into the active instance, set ESC active node into maintenance mode.

$ sudo escadm op_mode set --mode=maintenance

156

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Upgrading Cisco Elastic Services Controller

In-Service upgrade in VMware using ESC qcow2 Image

Step 6

Step 7

Step 8

Step 9

Step 10

Make sure there are no in-flight transactions and no new transactions during the upgrade. From ESC 2.3, you may use following commands to check in-flight transactions.

$ sudo escadm ip_trans

For build older than ESC 2.3, you may need to check escmanager log and make sure no new transactions are recorded in this log file. The log file can be located at (/var/log/esc/escmanager.log).

Power off ESC active node. In VMware vSphare Client, select Home > Inventory > VMs and Templates , right click the active instance name from the left panel, and select Power > Power Off .

VM will take over active role and provide ESC service.

$ sudo escamd restart

Check the ESC version on the new active instance to verify the upgraded version is correct. Once it is in the active state, make sure ESC service is running properly in the new active VM.

$ sudo escadm status

Expected output:

0 ESC status=0 ESC HA Active Healthy

$ esc_version

$ health.sh

Expected output:

ESC HEALTH PASSED

Power on the old active instance. In VMware vSphare Client, select Home > Inventory > VMs and Templates , right click the active instance name from the left panel, then select Power > Power On .

Log into the VM which is still with old ESC version and repeat step 2, 3, 4, and 7 in the VM.

In-Service upgrade in VMware using ESC qcow2 Image

Procedure

Step 1

Step 2

Backup ESC database and log files.

a) Perform ESC database backup from the active node. For more information on backing up the database, see

Backup the Database from the ESC HA Active/Standby Instances

b) Collect and backup all logs from both active and standby VMs. To backup the log, use the following command:

# sudo escadm log collect

Note A timestamped log file will be generated in: /var/tmp/esc_log-<timestamp>.tar.bz2

c) Copy the database backup file and logs files (generated in /tmp/esc_log-.tar.bz2)* out of ESC VMs.

Redeploy standby ESC instance. Register new ESC image on the standby instance, and wait for the data to be synchronized.

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

157

Upgrading Cisco Elastic Services Controller

In-Service upgrade in VMware using ESC qcow2 Image

Step 3

Step 4 a) Delete the standby instance. To delete the standby ESC instance, you need to first "Power Off" the instance through vSphere Client and then use the Delete from Disk option. In VMware vSphare Client, select

Home > Inventory > VMs and Templates , right click the instance name from the left panel, then select

Power > Power Off . Now to delete the standby instance, select Home > Inventory > VMs and Templates , right click the instance name from the left panel, then select Delete from Disk .

b) Redeploy the standby ESC VM instance based on newer image version. Re-install new the standby instance by using the new ESC package (bootvm.py and new registered image). Once the new ESC instance with upgraded version is up, it will be in standby state.

c) Log into the new instance and run the following command to check the synchronization state of the new

ESC node.

$ drbdadm status

Wait until the output of drbdadm status show both nodes are "UpToDate" like the output below. It means the new ESC instance has completed the data synchronization from the active instance.

esc/0 Connected Secondary/Primary UpToDate/UpToDate

Stop keepalived service on standby instance, Power off active instance, and then start standby keepalived service.

a) Log into the active instance, set ESC active node into maintenance mode.

$ sudo escadm op_mode set --mode=maintenance

Make sure there is no in-flight transaction ongoing before moving to the next step. To verify there are no in-flight transactions, use the following command:

For ESC 2.3:

$ sudo escadm ip_trans

For versions older than ESC 2.3, check escmanager log at (/var/log/esc/escmanager.log) and make sure there are no new transaction in escmanager log.

b) Log in to the upgraded standby instance and shut down the keepalived service.

$ sudo escadm stop c) Power off the active instance and make sure the active instance has been powered off. In VMware vSphare

Client, select Home > Inventory > VMs and Templates , right click the instance name from the left panel, then select Power > Power Off .

d) Log into the previously upgraded standby instance which is in stopped state and start the keepalived service. The standby ESC instance will take the active role (switchover will be triggered) and start providing services with new version.

$ sudo escadm start

Check the ESC version on the new active instance to verify the version is upgraded correctly.

$ sudo escadm status --v(check ha status)

Expected output:

0 ESC status=0 ESC HA Active Healthy vimmanager (pgid 41908) is running monitor (pgid 42067) is running mona (pgid 42130) is running drbd (pgid 38488) is active

158

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Upgrading Cisco Elastic Services Controller

In-Service upgrade in VMware using ESC qcow2 Image

Step 5

Step 6 snmp (pgid 2121) is running etsi (pgid 43247) is running pgsql (pgid 42566) is running keepalived (pgid 40281) is running portal (pgid 43307) is running confd (pgid 25644) is running filesystem (pgid 0) is running escmanager (pgid 42775) is running

$ esc_version (check esc version) version : 3.x.x

release : xxx

$ health.sh (check esc health)

Expected output:

ESC HEALTH PASSED

Re-deploy the old active instance with the new ESC image.

Delete the old active instance and redeploy it by using the new ESC package (bootvm.py and new registered image). All other installation parameters should be the same as the old ESC VM deployment. For example, hostname, ip address, gateway_ip, ha_node_list, kad_vip, kad_vif have to be the same values. To delete, in the VMware vSphare Client, access, Home > Inventory > VMs and Templates , right click the instance name from the left panel, then select Delete from Disk .

a) Log in to the new deployed instance and check ha status. The new instance should be in standby state:

$ sudo escadm status b) Run the following command to check the synchronization state of the new ESC standby node:

$ drbdadm status

Wait until the output of drbdadm status shown as UpToDate.

c) For the new ESC standby node, make sure the health check is passed and the ESC version are upgraded correctly.

$ sudo escadm status (check ha status)

Expected output:

0 ESC status=0 ESC HA Active Healthy

$ esc_version (check esc version)version : 3.x.x

release : xxx

$ health.sh

Expected output:

ESC HEALTH PASSED

Go back in to the first upgraded active instance and check the health and keepalived state.

$ drbdadm status

Expected output:

1:esc/0 Connected Primary/Secondary UpToDate/UpToDate /opt/cisco/esc/esc_database ext4

2.9G 52M 2.7G 2%

$ sudo escadm status (check ha status)

Expected output:

0 ESC status=0 ESC HA Active Healthy

$ esc_version (check esc version) Expected output:

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

159

Upgrading Cisco Elastic Services Controller

In-Service Upgrade of the ESC HA Active/Standby Nodes in CSP version : 3.x.x

release : xxx

$ health.sh (check esc health)

Expected output:

ESC HEALTH PASSED

Note Quick rollback: In case of an upgrade failure, shutdown the upgraded instance and start the old active instance to have a quick rollback.

Rollback Procedure for In-service Upgrade a.

Copy the database and log backup files to a location out of ESC VMs.

Delete any remaining ESC instance and redeploy ESC HA Active/Standby VMs using qcow2 image with old version.

Restore the database. Follow the procedures in the section, Upgrading ESC HA Active/Standby

Instance with Backup and Restore for HA Active/Standby database restore.

After database restore, you should have ESC service back with the old version.

In-Service Upgrade of the ESC HA Active/Standby Nodes in CSP

Follow the steps to do the In Service upgrade of the ESC HA Active/Standby Nodes in CSP:

Before you begin

Verify that the ESC HA nodes running properly before the upgrade, by using the following command:

# escadm status

One node must be in active state and the other node in standby state. Verify the Active node by using the following command:

# health.sh

On a successful health check you receive the following:

ESC HEALTH PASSED

Procedure

Step 1

Step 2

Shutdown the Standby instance

Upgrade the standby ESC VM, before power off the VM. To upgrade, follow the steps: a.

Collect the logs from the standby ESC VM, and copy it to another machine, by using the following commands:

# collect_esc_log.sh

# scp /tmp/LOG_PACKAGE_NAME <username>@<backup_vm_ip>:<filepath> b.

Using CSP, power off the standby ESC.

Deploy the standby node again using the new ESC package

160

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Upgrading Cisco Elastic Services Controller

In-Service Upgrade of the ESC HA Active/Standby Nodes in CSP

Step 3

Step 4

After power off the standby ESC VM, install new ESC VM for upgrading by using the new ESC package.

Except using different ESC packages from the former ESC VM, all other parameters for ESC installation must be the same as the previous ESC VM deployment.

Verify that the ESC node is in standby state. Use the following command to check the synchronization state of the new ESC standby node:

# drbdadm status

Wait until you get the following output, which shows that the new ESC VM has completed the data synchronization from the Active node and it is up to date.

[admin@esc-xyx-upgradetestha1-4-5-0-105 ~]$ drbdadm status esc role:Secondary disk:UpToDate

172.20.117.55:7789 role:Primary peer-disk:UpToDate

If a dynamic mapping file (dynamic_mapping.xm) is used by ESC service, it must be restored into the ESC

VM. Copy the Backup file to

/opt/cisco/esc-dynamic-mapping/ path.

Stop the Active node and trigger a switchover.

Power off the Active instance through CSP. Follows that, an HA switchover automatically triggers and the

Standby instance takes over the ESC service with the new ESC version. After new ESC instance becomes the

Active, verify that the new ESC Active node passes the health check.

Deploy new ESC node to replace old active

Install the new ESC VM for upgrading the previous active instance by using the new ESC package. Before powering off the ESC VM with the old version, collect the logs from the ESC VM, and copy it to another machine by using the following commands:

# collect_esc_log.sh

# scp /tmp/LOG_PACKAGE_NAME <username>@<backup_vm_ip>:<filepath>

Note If a dynamic mapping file is used by ESC service, the dynamic mapping file should be backed up at the same time with ESC logs. The default path of the dynamic mapping file is

/opt/cisco/esc/esc-dynamic-mapping/dynamic_mappings.xml.

Power off the ESC VM with old version through CSP.

Verify that the ESC node is in standby state. Use the following command to check the synchronization state of the new ESC standby node:

# drbdadm status

Wait until you get the following output, which shows that the new ESC VM has completed the data synchronization from the Active node and it is up to date.

[admin@esc-xyz-upgradetestha1-4-5-0-105 ~]$ drbdadm status esc role:Secondary disk:UpToDate

172.20.117.55:7789 role:Primary peer-disk:UpToDate

If a dynamic mapping file (dynamic_mapping.xm) is used by ESC service, it must be restored into the ESC

VM. Copy the Backup file to

/opt/cisco/esc-dynamic-mapping/ path.

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

161

Upgrading Cisco Elastic Services Controller

In-Service Upgrade of the ESC HA Active/Standby Nodes in CSP

Note If a dynamic mapping file is used by ESC service, the dynamic mapping file should be restored into the ESC VM. Copy the backup dynamic mapping file to the default path of the dynamic mapping file

/opt/cisco/esc/esc-dynamic-mapping/dynamic_mappings.xml.

Once you sucessfully complete the in-service upgrade, you can remove the old ESC instance.

Note After upgrading to the new ESC version, ESC service continues life cycle management of all VNFs deployed by the old version. If you want to apply any new feature of the new ESC version to existing

VNFs, undeploy those VNFs and do a new deployment.

162

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

P A R T

Troubleshooting Cisco Elastic Services

Controller Installation

•

Troubleshooting ESC Issues, on page 165

C H A P T E R

Troubleshooting ESC Issues

This chapter contains the following sections:

•

Viewing ESC Log Messages, on page 165

•

General Installation Errors, on page 170

•

ESC Failover Scenarios, on page 173

Viewing ESC Log Messages

Log messages are created for ESC events throughout the VNF lifecycle. These can be external messages, messages from ESC to other external systems, error messages, warnings, events, failures and so on. The log file can be found at /var/log/esc/escmanager_tagged.log

The log message format is as follows: date=<time-date>] [loglevel=<loglevel>] [tid=<transactionid>] [cl=<classifications>]

[tags=<tags>] [msg=<message>

Sample log is as follows: date=15:43:58,46022-Nov-2016]

[loglevel=ERROR ] [tid=0793b5c9-8255-47f3-81e6-fbb59f6571f7] [cl=OS ]

[tags=wf:create_vm,eventType:VM_DEPLOY_EVENT,tenant:CSCvd94541,depName:test-dep,vmGrpName:test-VNF, vmName:test-dep_test_0_dc3f406c-05ca-43b3-af21-0841e3b029a0]

[tags=wf:create_vm,eventType:VM_DEPLOY_EVENT,tenant:test,depName:test-dep,vmGrpName:test-VNF, vmName:test-dep_test_0_dc3f406c-05ca-43b3-af21-0841e3b029a0] [msg=sleepingfor5seconds to allow vm to become ACTIVE instance id:

162344f7-78f9-4e45-9f23-34cf87377fa7 name:test-dep_test_0_dc3f406c-05ca-43b3-af21-0841e3b029a0

When a request is received, a RequestDetails object is created which autogenerates a unique transaction id.

This value is carried forward across all threads. Classifications and tags are optional. These are prefixes added to the log messages to enhance readability, and help in debugging. With classifications and tags, the log messages can be easily parsed and filtered by the log analysis tools.

The following classifications are supported:

NBI

SBI

"com.cisco.esc.rest""com.cisco.esc.filter"(North Bound Interface -

Clientinterface)

"com.cisco.esc.rest"- source is a callback handler or"EventsResource"(South

Bound Interface - i.e. between ESC and the VIM)

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

165

Troubleshooting Cisco Elastic Services Controller Installation

Viewing ESC Log Messages

MONITORING

DYNAMIC_MAPPING

"com.cisco.esc.statemachines". stands for StateMachine. This classification indicates logs in the StateMachine category.

"com.cisco.esc.monitoring""com.cisco.esc.paadaptor"(MONA related logs)

"com.cisco.esc.dynamicmapping""com.cisco.esc.db.dynamicmapping"(MONA related logs)

CONFD "com.cisco.esc.confd"

CONFD_NOTIFICATION "com.cisco.esc.confd.notif""com.cisco.esc.confd.ConfdNBIAdapter"

LIBVIRT

"com.cisco.esc.vim.openstack"

"com.cisco.esc.vim.vagrant

VIM

REST_EVENT

"com.cisco.esc.vim"

"ESCManager_Event""com.cisco.esc.util.RestUtils". indicates REST notifications in logs.

"com.cisco.esc.watchdog"

"com.cisco.esc.datamodel""com.cisco.esc.jaxb.parameters"(Datamodel and resource objects)

SEC

MOCONFIG

POLICY

ESC

"com.cisco.esc.db"(Database related logs)

"com.cisco.esc.gateway"

"com.cisco.esc.ESCManager"(Start up related logs)

"com.cisco.esc.jaas"

"com.cisco.esc.moconfig"(MOCONFIG object related logs --this is internal for

ESC developers)

"com.cisco.esc.policy"(Service/VM Policy related logs)

"com.cisco.esc.threadpool"

"com.cisco.esc" Any other packages not mentioned above

The following tags are supported:

• Workflow [wf:] —Generated using action and resource from RequestDetails object. Example

"wf:create_network"

• Event type [eventType:] —Event that triggered the current action. Example:

"eventType:VM_DEPLOY_EVENT"

• Resource based —These values are generated based on the type of parameter used by the event. The hierarchy, that is, the tenant, the vm group and so on is added to the log.

Tenant [tenant:<tenant name>]

166

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Troubleshooting Cisco Elastic Services Controller Installation

Viewing ESC Log Messages

Network

Subnet

User

[tenant:<tenant id>, network:<network name>]

Note The tenant appears only if applicable.

[tenant:<tenant name or id>, network:<network name or id>, subnet:<subnet name>]

Note The tenant appears only if applicable.

[tenant:<tenant name>, user:<user name or id>]

Note The tenant appears only if applicable.

Image

Flavor

[image:<image name>]

[flavor:<flavor name>]

Deployment [tenant:<tenant name or id>, depName:<deployment name>]

DeploymentDetails [tenant:<tenant name or id>, depName:<deployment name>, vmGroup:<vm group name>, vmName:<vm name>]

Switch

Volume

Service

[tenant:<tenant name or id>, switch:<switch name>]

[volume:<volume name>]

[svcName:<Service Registration name>]

Further, ESC logs can also be forwarded to an rsyslog server for further analysis and log management.

Filtering Logs Using Confd APIs

You can query and retrieve logs (for example, deployment logs, or error logs ) in ESC using log filters introduced in the confd APIs. New filters for Tenant, Deployment Name, and VM Name are introduced. This enables you to query the ESC logs further for most recent error logs using the log filters in Confd APIs. You can also retrieve ESC logs related to the communication between ESC and the OS ( by setting the classification tag to "OS").

The log format to retrieve confd API logs: date=<time-date>] [loglevel=<loglevel>] [tid=<transactionid>] [cl=<classifications>]

[tags=<tags>] [msg=<message>

The sample log is as follows: date=15:43:58,46022-Nov-2016] [loglevel=ERROR ] [tid=0793b5c9-8255-47f3-81e6-fbb59f6571f7]

[cl=OS ]

[tags=wf:create_vm,eventType:VM_DEPLOY_EVENT,tenant:test,depName:test-dep,vmGrpName:test-VNF, vmName:test-dep_test_0_dc3f406c-05ca-43b3-af21-0841e3b029a0]

[msg=sleepingfor5seconds to allow vm to become ACTIVE instance id:

162344f7-78f9-4e45-9f23-34cf87377fa7 name:test-dep_test_0_dc3f406c-05ca-43b3-af21-0841e3b029a0

The parameters for log level, classification and tags are dependent on each other to retrieve the logs. You can successfully retrieve the logs with the following combination.

• log_level=ERROR, classifications=OS, tags=(depName:test-dep)

• log_level=ERROR, classifications=OS, tags=(tenant: test)

The log filter returns a value when all the following conditions are met:

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

167

Troubleshooting Cisco Elastic Services Controller Installation

Viewing ESC Log Messages

• Log level

• Classifications (if provided)

• Tags (if provided)

Note If there are more than one classification listed, it has to match at least one of the classifications. The same applies to the tags as well.

For example, the following log filter criteria does not return the log sample mentioned earlier: log_level=ERROR, classifications=VIM, tags=(depName:test-dep)

It does not return any value though the log level and tags match, the classification VIM does not match.

The data model is as follows: rpc filterLog { description "Query and filter escmanager logs using given parameters"; tailf:actionpoint escrpc; input { leaf log_level { mandatory false; description "One of DEBUG / INFO / WARNING / ERROR / TRACE / FATAL. Results will include all logs at and above the level specified"; type types:log_level_types; default ERROR;

} leaf log_count { mandatory false; description "Number of logs to return"; type uint32; default 10;

} container classifications { leaf-list classification { description "Classification values to be used for the log filtering.

For example:

'OS', 'SM'.

Logs containing any of the provided classification values will be returned."; type types:log_classification_types;

}

} container tags { list tag { key "name"; leaf name { mandatory true; description "Tag name to be used for the log filtering.

For example: 'tenant',

'depName'.

Logs containing any of the provided tag name plus the tag values will be returned."; type types:log_tag_types;

} leaf value { mandatory true; description "Tag value pairs to be used for the log filtering.

For example:

'adminTenant', 'CSRDeployment'"; type string;

}

168

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Troubleshooting Cisco Elastic Services Controller Installation

Viewing ESC Log Messages

}

} output { container filterLogResults { leaf log_level { description "Log level used to filter for the logs."; type types:log_level_types;

} list logs { container classifications { leaf-list classification { description "Classifications used to filter for the logs."; type types:log_classification_types;

}

} container tags { list tag { key "name"; leaf name { mandatory true; description "Tag name used to filter for the logs."; type types:log_tag_types;

} leaf value { mandatory true; description "Tag value used to filter for the logs."; type string;

}

} leaf log_date_time { description "Timestamp of the log."; type string;

} leaf log_message { description "The log message."; type string;

}

You can query for the confd API logs through the netconf console or esc_nc_cli

• Through the netconf-console, run the following query:

/opt/cisco/esc/confd/bin/netconf-console --port=830 --host=127.0.0.1 --user=admin

--privKeyFile=/home/admin/.ssh/confd_id_dsa --privKeyType=dsa --rpc=log.xml

• Using the esc_nc_cli, run the following query: esc_nc_cli --user <username> --password <password> filter-log log.xml

The sample log.xml is as follows:

<log_level>INFO</log_level>

<log_count>1</log_count>

</classifications>

<tags>

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

169

Troubleshooting Cisco Elastic Services Controller Installation

General Installation Errors

<tag>

<name>depName</name>

</tag>

<tag>

<name>tenant</name>

<value>admin</value>

</tag>

</tags>

</filterLog>

The response is as follows:

<rpc-reply xmlns="urn:ietf:params:xml:ns:netconf:base:1.0" message-id="1">

<log_level>INFO</log_level>

<logs>

</classifications>

<tags>

<tag>

<name>depName</name>

</tag>

<tag>

<name>tenant</name>

<value>admin</value>

</tag>

</tags>

<log_date_time>13:06:07,575 31-Oct-2016</log_date_time>

<log_message> No pending work flow to start.</log_message>

</logs>

</filterLogResults>

</rpc-reply>

Note The logging API responses are in XML format. If the log messages contain any

XML characters, then the characters will be escaped so not to break the XML conformance.

General Installation Errors

This section cover some of the common installation problems and how to troubleshoot them.

170

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Troubleshooting Cisco Elastic Services Controller Installation

General Installation Errors

Problem/Error Possible Reason User Action

Issues encountered while verifying ESC services status at the installation time using sudo escadm status

Some services take time to start or have trouble starting.

Identify the issues using one of the following method:

• Check the log /var/log/esc/escadm.log

$ cat /var/log/esc/escadm.log

• Add '-v' to escadm status to show the verbose output of the ESC services and see the services are up and running.

Confirm the status of the identified services that has issues and manually start these services.

$ sudo escadm <<service>> status//

If the status is stopped or dead, manually start the services using the next command.

$ sudo escadm <<service>> start --v

Authentication related error during the ESC installation

OpenStack credential-related arguments are missing.

ESC HA-related (Active/Standby) Issues

Network Problem

Source your OpenStack RC file and verify the OpenStack clients work properly

Check for the following:

• The static IP addresses for both ESC nodes used are based on the OpenStack configuration.

• The gateway for each network interface is accessible.

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

171

Troubleshooting Cisco Elastic Services Controller Installation

General Installation Errors

Problem/Error Possible Reason User Action

ESC active node stays in the

"switching-to-active" state

This could be because of the following issues:

Check for the:

• ESC HA

Active/Standby node can not reach its peer during the initial installation.

• Connectivity between ESC active node and standby node. For initial installation, ESC active service won't be up if it can't reach the standby node. You need to make sure you have both ESC nodes successfully deployed and they can reach each other.

• ESC logs at /var/log/esc/esc_haagent.log (ESC 2.X) or /var/log/esc/escadm.log (ESC 3.X) to identify the services that has issues.

• ESC service

(tomcat) can't start properly due to database problems

(etc. database migration, database file corruption).

• Log at /var/log/esc/escmanager.log for esc_service and postgresql issues.

• Confd can't start due to the CDB file corruption.

• Postgresql can't start or init due to the file system issues.

• The connection between ESC nodes is too slow.

MTU issues for ESC

HA Active/Standby

For the ESC VMs, reduce the MTU for network interfaces from 1500 to 1450. Follow the below steps to reduce the

MTU value:

Identify the interface you would like to change. Access the interface from the location,

/etc/sysconfig/network-scripts/ifcfg-ethX, where X represent the interface number you want to change.

Use a text editor like VIM to add or edit the MTU items for the interface, for instance, set MTU = 1450

Restart the interface.

network service restart

172

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Troubleshooting Cisco Elastic Services Controller Installation

ESC Failover Scenarios

Problem/Error

Other Issues

Possible Reason User Action

There are several useful logs to check for ESC HA

Active/Standby troubleshooting.

• ESC manager log is located at

/var/log/esc/escmanager.log

• ESC HA Active/Standby log about esc service startup/stop is located at /var/log/esc/esc_haagent.log

for ESC 2.X and /var/log/esc/escadm.log for ESC 3.X

• For Keepalived configuration:

• Check the configuration file at

/etc/keepalived/keepalived.conf

• Keepalived log is located at /var/log/messages by grep keepalived or vrrp

• For DRBD configuration:

• DRBD configuration can be verified by checking the file at /etc/drbd.d/esc.res

• The DRBD log is located at /var/log/messages by grep drbd

ESC Services Startup Issues

Service status reports

ETSI service is dead at installation time using sudo escadm status --v

If the host has multiple

IP addresses the ETSI service is unable to determine which IP address to use when generating callback

URLs.

This cause can be verified by examining the log file

/var/log/esc/etsi-vnfm/etsi-vnfm.log

for an exception including:

Configure server.host

property in configuration file.

Set the server.host property: sudo escadm etsi set –server_host <IP>

Start the ETSI service: sudo escadm etsi start

ESC Failover Scenarios

• When customer deploys many VNFs

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

173

ESC Failover Scenarios

Troubleshooting Cisco Elastic Services Controller Installation

• When customer does a DB backup

• One or more of the VMs in the VNFs is recovered via redeploy – new VM ID

• ESC Fails – It is a permanent failure

• Customer Restores DB – When there is a mismatch between 1 or more VM IDs

• Same VNF fails, but when ESC tries to recover, it fails because it is not found on the VIM by VM ID and redeploy fails because the ports are in use.

• The workaround is to delete the VM out of band and recover – if the VM is deleted it is not found by

ESC and the port is available for redeployment.

174

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

A P P E N D I X

Cisco Elastic Services Controller Installer

Arguments

You need to specify the following bootvm.py

script arguments to boot ESC instances.

Arguments Description esc_hostname

--image

Specifies the host name of the ESC VM instance.

Specifies the image id used in the OpenStack glance to boot up the

ESC instance.

--boot_volume

--ignore-ssl-errors

--managers

Specify the volume name or id of the external bootable volume from where you want to launch ESC instance.

It sets the "ignoreSslErrors" to "yes". It helps in deploying to a development or test environment when you don't have a root trusted certificate installed.

It is a comma delimited list of locations where SNMP traps is delivered.

It must be supplied in the following format: udp:ipv4/port" or "udp:[ipv6]/port

--net

--ipaddr

Specifies the Network IDs or names in OpenStack that ESC connects to.

(Optional) Specifies the IP addresses that ESC will be assigned in the network.

Note The IP address must correspond to the net_id in the --net argument.

--gateway_ip

--os_auth_url

--os_username

(Optional) Specifies the default gateway IP address of ESC.

(Optional) Specifies the OpenStack keystone url used by os_auth_url for authentication.

(Optional) Specifies the OpenStack keystone username used by os_username for authentication.

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

175

Cisco Elastic Services Controller Installer Arguments

Arguments

--os_password

--os_tenant_name

--bs_os_auth_url

--bs_os_username

--bs_os_password

--bs_os_tenant_name

--flavor

--security_rules_file

--etc_hosts_file

--avail_zone

--esc_params_file

--etsi_params_file

--db_volume_id

-- ha_node_list

--kad_vip

--kad_vif

Description

(Optional) Specifies the OpenStack keystone password used by os_password for authentication.

(Optional) Specifies the OpenStack tenant name used by os_tenant_name for ESC deployment.

(Optional) Specifies the OpenStack keystone url used by bs_os_auth_url for authentication.

(Optional) Specifies the OpenStack keystone username used by bs_os_username for authentication.

(Optional) Specifies the OpenStack keystone password used by bs_os_password for authentication.

(Optional) Specifies the OpenStack tenant name used by bs_os_tenant_name for ESC deployment.

(Optional) Specifies the OpenStack flavor id to boot the ESC VM.

(Optional) Specifies the file to define security rules (IP, Port security) for ESC VM.

(Optional) Specifies the file for adding more entries to the ESC vm's hosts file (/etc/hosts).

(Optional) Specifies the OpenStack zone used for ESC deployment.

(Optional) Specifies the default parameter file for ESC deployment.

(Optional) Specifies the ETSI properties file for ESC deployment.

(Optional) Specifies the cinder volume id to mount for database storage in ESC HA Active/Standby [ESC-HA Active/Standby].

(Optional) Specifies list of IP addresses for HA Active/Standby nodes in the Active/Standby cluster. For ESC nodes with multiple network interfaces, these IPs should be the addresses in the network used for data synchronization.

Note This argument is utilized for replication-based HA

Active/Standby solution only.

(Optional) Specifies the IP address for Keepalived VIP (virtual IP) plus the interface of Keepalived VIP [ESC-HA Active/Standby].

An example format for specifying the interface of VIP is --kad_vip

192.0.2.1:eth2 or --kad_vip [2001:cc0:2020::fc]:eth2

(Optional) Specifies the interface for Keepalived virtual IP and keepalived VRRP [ESC-HA Active/Standby]. You can also use this argument to only specify the interface for Keepalived VRRP, if the

VIP interface is already specified using the kad_vip argument.

176

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Cisco Elastic Services Controller Installer Arguments

Arguments

--kad_vri

--route

--ntp_server

--rsyslog_server

--rsyslog_server_port

--rsyslog_server_protocol

--secure

--host_mapping_file

--version

--rng_virtio

Description

Specified the virtual router id of vrrp instance. Accepted values for kad_vri are 0 to 254. ESC VMs in the same HA Active/Standby should use the same kad_vri number. If kad_vip is not used for L3 HA

Active/Standby, the kad_vir has to be used, otherwise, you can skip kad_vri argument.

Specifies the routing configuration for ESC VM.

(Optional) Specifies the NTP server address.

(Optional) Specifies the IP address of rsyslog server that ESC sends the log to

(Optional) Specifies the port of rsyslog server that ESC sends the log to.

(Optional) Specifies the protocol to be used by the ESC to forward logs to the server.

(Optional) Enables secure configuration. You can specify the following values:

• A —Root is completely locked out. You cannot login as a root even from the console.

• B —SELinux runs in the enforcing mode.

• C —IPv4/IPv6 tables are started.

• D —SSH password authentication is disabled. You need the private key to ssh into ESC vm.

• E —host keys for confd will be re-created.

(Optional) Specifies the host mapping file for VNF deployment.

(Optional) Prints the version of bootvm.py and exits.

Enables installing and deploying the ESC VM on Libvirt/KVM with the RNG Virtio device. The default values are: device=/dev/random rate_period=1000 rate_bytes=1024

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

177

Cisco Elastic Services Controller Installer Arguments

Arguments

--user_pass

Description

This along with --user_confd_pass are mandatory arguments from 3.0

onwards.

This argument adds a user to access the ESC VM. Use this argument to specify a user without administrative privileges, i.e, a non-admin/non-root user. Use the following format: user_name:password. The bootvm.py command requires at least one

--user_pass argument to create an admin account for linux (ssh/console access) . The following is the syntax for the mandatory user credential argument:

--user_pass admin:'PASSWORD-OR-HASH'[:OPTIONAL-PUBLIC-KEY-FILE][:OPTIONAL-ROLE]

This user can only do the following:

• Login to ESC through SSH.

• Access and drive the Netconf CLI, such as, esc_nc_cli, netconf-console, and so on.

• Read ESC -related logs from /var/logs/esc

• Access REST interface through localhost

This user cannot:

• Access the ESC DB and reconfigure ESC system.

• Access the system-level logs

• Configure the system level components, such as: Rsyslog,

Keepalived, DRDB, and so on.

• Access the encryption keys and values from REST interface or

ESC logs.

Following is an example of --user_pass for admin account and stronger clear text passwords. Use single quotes to avoid conflict with shell reserved characters:

-user_pass admin:'Strong4Security!'.

Another example to install ESC using a password hash for both admin accounts. Use single quotes to avoid conflict with shell reserved characters:

--user_pass admin:'$algorithm$salt$hash-of-salt-password'.

ESC 2.1 and later, accepts the public key for this attribute. For example, the following will generate 'admin321' as the password for user 'admin' and use /tmp/abc.pub

as the key file to inject the public key for it:

--user_pass admin:admin321:/tmp/abc.pub

178

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Cisco Elastic Services Controller Installer Arguments

Arguments

--user_confd_pass

--esc_portal_startup

--log

--esc_monitor_check_ips

--enable-https-rest

--enable-http-rest

--disable-rest-auth

--enable-snmp-agent

--ha_mode

--enable-https-etsi

Description

Used to change confd users. The bootvm.py command requires at least one --user_confd_pass to create an admin account for ConfD

(netconf/cli access). The following is the syntax for the mandatory user credential argument:

--user_confd_pass admin:'PASSWORD-OR-HASH'[:OPTIONAL-PUBLIC-KEY-FILE]

Following is an example of --user_confd_ pass for admin account and stronger clear text passwords. Use single quotes to avoid conflict with shell reserved characters:

--user_confd_ pass:'Strong4Security!'.

Another example, to install ESC using a password hash for both admin accounts. Use single quotes to avoid conflict with shell reserved characters:

--user_confd_ pass:'$algorithm$salt$hash-of-salt-password'.

ESC 2.1 and later, accepts the public key for this attribute. For example, the following will generate 'admin321' as the password for user 'admin' and use /tmp/abc.pub

as the key file to inject the public key for it:

--user_confd_ pass:admin321:/tmp/abc.pub

(Optional) Starts the ESC portal.

(Optional) Specifies the log file. By default, logs to stdout.

(Optional) Specifies the IP addresses that must be monitored by esc_monitor (for HA Active/Standby failover).

(Optional) Enables a secure REST Interface for the created ESC VM.

(Optional) Enables an unsecured REST Interface for the created ESC

VM.

(Optional) Disables REST API authentication.

Note REST authentication should not be disabled in a production environment.

(Optional) Enables automatic start-up of the SNMP service. The default value is False.

Specifies the ESC HA Active/Standby mode for HA Active/Standby installation. Specify one of the following available options for HA

Active/Standby: no_ha : No HA, cinder : Shared Cinder Volume, drbd :

Built-in DRBD, drbd_on_cinder : DRBD over Cinder Volume

(Optional) Enables a secure ETSI REST Interface for the created ESC

VM.

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

179

Cisco Elastic Services Controller Installer Arguments

Arguments

--enable-http-etsi

--encrypt_key

--proxy

--noproxy

--kad_unicast_src_ip

--kad_unicast_peer

--placement_hint

--format {json}

--user_rest_pass

--user_portal_pass

--user_etsi_pass

--etsi_oauth2_pass

Description

(Optional) Enables an unsecured ETSI REST Interface for the created

ESC VM. Enabling this interface is not recommended in a production environment.

Specifies the key for encryption.

Uses the proxy on a given port.

Lists the hosts which do not use proxy.

Specifies the source IP address of unicast. Should be the IP address of interface that ESC VM uses for unicast (L3) VRRP communication.

Example: --kad_unicast_src_ip 10.0.0.1

Specified the peer IP addresses of unicast. Should be the ip address of interface that ESC peer VM uses for unicast (L3) VRRP communication.

Example: --kad_unicast_peer 10.0.0.1

Use this argument to specify the placement of ESC HA Active/Standby virtual machines using the server group, samehost, differenthost filters.

Example:

• --placement_hint different_host=2b299428-e7a7-4528-8566-9a4970183c6a [ID should be the VM uuid]

• --placement_hint same_host=2b299428-e7a7-4528-8566-9a4970183c6a [ID should be the VM uuid]

• --pacement_hint group=4c7758ab-e9cb-4cf0-8f02-344ec666365b

[ID should be the server group uuid]

Use this argument to capture the success and failure message in the output.

Example: $ ./bootvm.py --image ESC-2_3_0_8 --net network --format json --test-0

{ "status" : "Success" , "vm_uuid" : "UUID" }

Adds a user to access the Rest API. Format is username: password.

This option can be repeated.

Add a portal user. Format username: password. This option can be repeated.

Adds a user to access the ETSI REST API. Format username:password.

Only a single user can be supplied.

Add an OAuth2 client for access to the ETSI REST API. Format clientId:clientSecret. This option can be repeated.

180

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Cisco Elastic Services Controller Installer Arguments

Arguments

--no_vim_credentials

Description

Use this argument to deploy ESC without passing the VIM credential.

If this argument is used, following parameters will not be passed during the installation:

• --os_auth_url

• --os_username

• --os_password

• --os_tenant_name

After the deployment is complete, the user can set these VIM credential through ESC's VIM/VIM User APIs (REST/Netconf). For more information on configuring through REST APIs and Netconf, see

Configuring VIM credentials after installing ESC in the Post Installation

Tasks chapter.

Cisco Elastic Services Controller Installer File Reference

File Description security_rules_file The file contains the following:

• Security rules to create a security group for the tenant.

• Configurations to allow traffic for the tenant.

etc_hosts_file esc_params_file

The file contains one or more entries that you want to include in the /etc/hosts file.

The file contains information to configure various parameters of ESC. For details on parameters that can be configured in the esc_params_file are described in table below.

host_mapping_file The file contains information to map a network based on the hosts.

ESC Configuration Parameters

Using this file, you can configure various ESC parameters during the installation. The parameters that can be configured are shown in the table.

Below is an example configuration using this file: openstack.endpoint=adminURL affinity.filter=ServerGroupAffinity

Table 7: ESC Configuration Parameters esc_param.conf

Type default.vm_recovery_retries_max

Int

Default Value

Description

Number of recovery attempts allowed per VM.

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

181

Cisco Elastic Services Controller Installer Arguments

Cisco Elastic Services Controller Installer Arguments esc_param.conf

Type openstack.endpoint

String

Default Value publicURL

Description

The parameter to set up the keystone endpoint value of

ESC. Options: adminURL, publicURL

You can change the default value using CLI or REST services.

Using CLI:

$ sudo escadm escmanager config set --key openstack.endpoint

--value publicURL

{

"category": "OPENSTACK",

"type": "STRING",

"value": "publicURL",

"key": "ENDPOINT"

}

Using REST: log.level

affinity.filter

String

INFO

SameHostFilter

$ curl -X PUT http://172.16.0.1:8080/ESCManager/v0/config

/openstack/endpoint/publicURL

Level of logging. Options: INFO, Trace, DEBUG

A constant string used to build PolicyEngine and initializing VM policy table.

Options: SameHostFilter, ServerGroupAffinity anti_affinity.filter

String

DifferentHostFilter

A constant string used to build PolicyEngine and initializing VM policy table.

Options: DifferentHostFilter

Note ESC uses SameHostFilter and DifferentHostFilter for ESC policy engine by default but OpenStack may not configure those filters by default. You may need to add SameHostFilter and DifferentHostFilter to the following scheduler options in the /etc/nova/nova.conf

file of the nova service in your OpenStack.

scheduler_default_filters = RetryFilter, AvailabilityZoneFilter,RamFilter, ComputeFilter,

ComputeCapabilitiesFilter,

ImagePropertiesFilter, ServerGroupAntiAffinityFilter, ServerGroupAffinityFilter,

DifferentHostFilter, SameHostFilter

ServerGroupAntiAffinityFilter for Openstack

ESC adapts to use ServerGroupAntiAffinityFilter for Openstack.

REST

PUThttp://localhost:8080/ESCManager/v0/config/anti_affinity/filter/ServerGroupAntiAffinity

PUThttp://localhost:8080/ESCManager/v0/config/affinity/filter/ServerGroupAffinity

182

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Cisco Elastic Services Controller Installer Arguments

CLI sudo escadm escmanager config set --key ANTI_AFFINITY.FILTER --value ServerGroupAntiAffinity sudo escadm escmanager config set --key AFFINITY.FILTER --value ServerGroupAffinity

Important Points

ServerGroupAntiAffinityFilter from Openstack doesn't support inter-dep anti-affinit, scaling, and mix use of

ServerGroup and default (SameHost/DifferentHost) filter. If you are using ServerGroupAntiAffinity filter,

Intra vm group placement is not allowed. You can only use <placement_group> for the VM based placement policy, one VM per vm_group. You can not add a single vm group in two different placement_groups.

ESC Services, Ports, and Security Group Overview

Table 8: External Services

Service sshd

ESC Web

UI/Portal

(HTTPS)

Visibility Optional?

External

(Orchestration)

Interface

0.0.0.0

External

(Orchestration)

Yes

(REST and/or

Netconf can be used instead)

0.0.0.0

ESC Netconf

API

External

(Orchestration)

Yes

(REST and/or Portal can be used instead)

0.0.0.0

ESC SNMP External

(Orchestration)

Yes (only configurable through custom user-data/esc-config.yaml)

0.0.0.0

ESC DRBD

(HA

Active/Standby

Replication)

External

(Orchestration)

No. Required for HA

Active/Standby setup.

0.0.0.0

ESC ConfD

CLI

External Yes

Configurable by modifying and reloading esc_production_confd.conf

0.0.0.0

ESC REST

API (HTTPS)

External

(Orchestration)

Yes

(Portal and/or

Netconf can be used instead)

0.0.0.0

Protocol

TCP

SSH

TCP

Port

443

(Previously

9001)

830

2001

7789

2024

8443

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

183

Cisco Elastic Services Controller Installer Arguments

Service

ESC Health

API

Visibility Optional?

External

(Orchestration)

Interface

ESC

Keepalived

ETSI-VNFM

(HTTP)

External

(Orchestration)

No. Required for HA

Active/Standby setup.

0.0.0.0

External Yes (configurable through etsi-production.properties)

0.0.0.0

ETSI-VNFM

(HTTPS)

External

ETSI-VNFM

(Prometheus)

ETSI-VNFM

(Additional

HTTPS Port for artifacts download)

External

Yes (configurable through etsi-production.properties)

0.0.0.0

Yes (configurable through etsi-production.properties)

0.0.0.0

Yes (configurable through etsi-production.properties)

0.0.0.0

Protocol

Multicast

VRRP

TCP

Port

N/A

8250

8251

8252

8253

For ESC 5.2

and later,

8060

For ESC 5.1

and earlier,

60000

Local only ETSI Health

API

Internal

External D-MONA

REST API

Consul

Service

External

Consul

Service

ConfD

PostgreSQL

External

No for A/A set

0.0.0.0

TCP

Limited to

ESC node

IPs

TCP

Limited to

ESC node

IPs

TCP

8443

TCP

TCP and

UDP

8300, 8301,

8302

8301

8302

8600

4565

7878

184

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

Cisco Elastic Services Controller Installer Arguments

Service Visibility

ESCManager

RMI

Registry

External

ESCManager

RMI Service

External

Optional?

No for A/A set

Interface

Limited to

ESC node

IPs

Protocol

TCP

No for A/A set Limited to

ESC node

IPs

TCP

ESCManager

Prometheus

Metrics

External

MONA

Prometheus

External

VIMManager

Prometheus

Metrics

External

DHCP

Yes.

(application.properties)

Yes.

(application.properties)

Yes.

(application.properties)

External

DHCP is limited to resolving IP addresses for

ESC interfaces.

0.0.0.0

TCP

UDP

Only needed for A/A ESC set. Otherwise, the port will not listen.

Introduced only since ESC 5.0

ESC A/A set (3 VMs)

Introduced only since ESC 5.0

ESC A/A set (3 VMs)

Only needed for A/A ESC set. Otherwise, the port is not listened.

ESC 5.2 and later

Port

8679

8680

8088

8092

8097

66,67

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

185

Cisco Elastic Services Controller Installer Arguments

186

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

A P P E N D I X

List of Variables Used in CSP 2100 Sample Files

To create the user-data file, to configure the ESC you must have values ready for the following list of variables used in the sample files:

Table 9: List of Variables

Variable Name

VAR_TIMEZONE

VAR_SERVICE_NAME

VAR_NTP_SERVER

VAR_NETWORK1_NETMASK

VAR_NETWORK1_NAME

VAR_NETWORK1_IPADDR

VAR_NETWORK1_GATEWAY

VAR_NETWORK0_NETMASK

VAR_NETWORK0_NAME

VAR_NETWORK0_KADVRI

VAR_NETWORK0_KADVIP

VAR_NETWORK0_IPADDR2

Purpose

The timezone for the ESC clock to use

The name of the ESC service on the CSP

The IP address of an NTP server

The netmask for the eth1 interface (Dual Interface

ESC)

The name of the network on the CSP where ESC's eth1 interface exists (Dual Interface ESC)

The IP address for the eth1 interface (Dual Interface

ESC)

The gateway for the eth1 interface (Dual Interface

ESC)

The netmask for the eth0 interface

The name of the network on the CSP where ESC's eth0 interface exists

The VRRP ID used for HA. Must be unique in the subnet for the HA pair and the same value used on both ESCs

Range is from 1 to 254

The VIP for the HA pair that connects to the current

Active ESC

The IP address for the other ESC's eth0 interface

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide

187

List of Variables Used in CSP 2100 Sample Files

Variable Name

VAR_NETWORK0_IPADDR

VAR_NETWORK0_GATEWAY

VAR_NAMESERVER_IP

VAR_LOCAL_HOSTNAME

CSP_IP_ADDRESS

List of Variables Used in CSP 2100 Sample Files

Purpose

The IP address for ESC (eth0 interface)

The gateway for the eth0 interface

The IP address of a DNS server

The hostname for ESC

IP address of the CSP 2100 to be used

188

Cisco Elastic Services Controller 5.5 Install and Upgrade Guide