Datalogic S3Z Data Sheet

MINIATURE SENSORS
S3Z
C ATA L O G
SECTION
ADVANCED GLOBAL STYLE
MINIATURE PHOTOELECTIC
SENSOR
•
•
•
•
•
•
50-250 mm background suppression
0.7 m proximity, 150 mm with narrow beam
4 m polarized retroreflective
15 m through beam
Light and dark trimmer models
Standard 3-wire output configuration
APPLICATIONS
• Processing and Packaging machinery
• Electronics assembling
• Transportation lines, material handling
• Automatic warehouses
• Cosmetics and Pharmaceutical industry
• Small part detection with maximum accuracy
S3Z
0…15 m
0…30 m (class 1 LASER)
0.05…4 m
0,3…10 m (class 1 LASER)
Through beam
Polarized retroreflective
Retroreflective for transparent (on R2 reflector)
0…2 m
Diffuse proximity
Background suppression
Power supply
Output
Connection
Approximate dimensions (mm)
Housing material
Mechanical protection
32
CATALOG | Photoelectric Sensors
S3N
Vdc
Vac
Vac/dc
PNP
NPN
NPN/PNP
relay
other
cable
connector
pig-tail
0…700 mm
50…150 mm (narrow beam)
50…250 mm
40…300 mm (class 1 LASER)
10…30 V
•
•
•
•
11x31x19
PC/PBT
IP67
TECHNICAL DATA
30 mA max. (LED mod.)
35 mA max. (Laser mod.)
red LED 650 nm (mod. S3Z…T51)
red LED 665 nm (mod. S3Z…B01/C01)
red LED 670 nm (mod. S3Z…M01)
IR LED 850 nm (mod. S3Z…C11)
IR LED 870 nm (mod. S3Z…F01/G00)
red Laser 650 nm (mod. S3Z…B01/F01/G00/M01)
sensitivity trimmer, 6 turns screw (mod. S3Z...M01),
one turn sensitivity trimmer
LIGHT/DARK trimmer (Laser mod. S3Z...-PP, -NN), LIGHT (mod. S3Z...-PL, -NL),
DARK (mod. S3Z...-PD, -ND)
yellow OUTPUT LED, green STABILITY LED (mod. S3Z...B01/C01/C11/F01), POWER ON LED (mod.
S3Z...G00)
Consumption (output current excluded)
Light emission
Setting
Operating mode
Indicators
Output
Output current
PNP or NPN (short circuit protection)
100 mA max.
2 V max. (LED mod.)
1,5 V max. (Laser mod.)
1 ms max. (LED mod.)
250 µs max. (Laser mod.)
500 Hz max. (LED mod.)
2 kHz max. (Laser mod.)
2 m cable Ø 3,5 mm, M8 4-pole connector
Saturation voltage
Response time
Switching frequency
Connection
Dielectric strength
Insulating resistance
Mechanical protection
Ambient light rejection
Vibration
Shock resistance
Housing material
Lens material
Operating temperature
Storage temperature
Weight
500 Vac 1 min., between electronics and housing
>20 MΩ 500 Vdc, between electronics and housing
IP67
according to EN 60947-5-2
0.5 mm amplitude, 10 … 55 Hz frequency, for every axis (EN60068-2-6)
11 ms (30 G) 6 shock for every axis (EN60068-2-27)
body PBT, indicators cover PC
PMMA, PC (mod. S3Z…B01)
-25 ... 55 °C (LED mod.), -10 ... 55 °C (Laser mod.)
-40 … 70 °C (LED mod.), -25 ... 70 °C (Laser mod.)
50 g max. cable vers. , 10 g max. conn. vers.
DIMENSIONS
DIMENSIONS
DIMENSIONS
SERIES
S3Z SERIES
CTION
MANUAL
NSTRUCTION
MANUAL
ONTROLS
CONTROLS
OUTPUT LED
POWER ON LED
(S3Z...G00)
TRIMMER
S3Z
F01/G00
STABILITY
LED
TRIMMER
S3Z
S3Z
S3Z
B01/C01/C11/M01
B01/C01/C11/M01
F01/G00
Emitter or
Receiver
Receiver
Emitter
or
Receiver
SETTING
SETT
OUTPUT LED
POWER ON LED
(S3Z...G00)
OUTPUT LED
POWER ON LED
(S3Z...G00)
STABILITY LED
S3Z...T51
TRIMMER
STABILITY LED
TRIMMER
OUTPUT LED
POWER ON LED
(S3Z...G00)
STABILITY LED
S3Z...T51
Receiver
Emitter and
Receiver
Coaxial
Emitter and
Receiver
Coaxial
CABLE
VERSION
ED
LED
indicates
output
status.the output status.
CABLE
VERSION
Alignment S3Z…B01/T51
Alignment S3Z…B01/T51
Position the sensor
and
reflector
Position
the
sensor on
andopposite
reflectorsides.
on op
Turn the sensitivity
trimmer
to maximum.
Turn the
sensitivity
trimmer toFind
maxit
yellow LED (OUT)
is switched
ONswitched
and OFF
yellow LED
(OUT) is
ON
horizontal positions,
and
fix
the
sensor
in
the
c
horizontal positions, and fix the sen
points.
points.
Optimum operation
is
obtained
when
the
green
LED
Optimum operation is obtained when t
If necessary, reduce
sensitivity
using
the trimmer,
If necessary,
reduce
sensitivity
using i
small or transparent
In order
to improve
small ortargets.
transparent
targets.
In order
procedure detailed
abovedetailed
whilst progressively
redu
procedure
above whilst progr
Alignment S3Z…F01/G00
Alignment S3Z…F01/G00
Position the sensors
opposite
Positionon
the
sensorssides.
on opposite sides
Find the points
where
yellow
LED
swi
Find
the the
points
where
the(OUT)
yellowisLED
both vertical and
positions,
andpositions
fix the
both horizontal
vertical and
horizontal
between thesebetween
points. these points.
Optimum
operation
is obtained
when
t
Optimum operation
is obtained
when
the green
LED
Alignment S3Z…C01/C11
(LIGHT m
Alignment S3Z…C01/C11
(LIGHT mode)
Position
theturn
sensor
and turn the
sensi
Position the sensor
and
the sensitivity
trimmer
green
LED
ON and
theisyellow
the green LEDthe
is ON
and
theisyellow
LED
OFF. L
Place
the target
opposite the sensor.
Place the target
opposite
the sensor.
Emitter
Emitter
Turn thetrimmer
sensitivity
trimmeruntil
clockw
Turn the sensitivity
clockwise
th
yellow
turnsdetected
ON (Target
detected
yellow LED turns
ONLED
(Target
state,
pos.A)
N
0)LED (S3Z…G00)
Remove
the
target,
the
yellow
LE
Remove
the
target,
the
yellow
LED
turns
OFF
LED
the sensor is operating.
theindicates
sensor isthat
operating.
Dimensions in mm
Dimensions in mm
untilLED
the turns
yellowON
LED
turns
clockwise untilclockwise
the yellow
(Backgr
S3Z…B01/C01/C11/F01/T51)
C11/F01/T51)
trimmer
reachesif max
pos.B). The pos.B).
trimmer The
reaches
maximum
the
r
can
be
used
to
adjust
sensitivity;
the
operating
distance
o adjust sensitivity; the operating distance
Turntothe
to the inte
detected. Turndetected.
the trimmer
thetrimmer
intermediate
po
rning
the trimmer clockwise.
clockwise.
two
positions
and B.
The
green
two positions A
and
B. The A
green
LED
must
be LED
ON
For S3Z…C01/C11
models
in DARK
For
S3Z…C01/C11
models
in
DARK
mode,
the
O
ENT
SCREW
(S3Z…M01)
Z…M01)
00
M8 CONNECTOR
S3Z…F01/G00
output are inverted.
S3Z…T51 S3Z…T51
S3Z…B01 S3Z…B01
S3Z…C01 S3Z…C01
S3Z…C11 S3Z…C11
S3Z…F01/G00
S3Z…M01 S3Z…M01
output are inverted.
can bethe
used
to adjust
the(6cutoff
adjust
cutoff
distance
turnsdistance
screw); (6 turns screw);
g distance
turning
the control clockwise. Power supply:Power supply:
… 24 Vdc
(operating
limit 10…30Vdc);
reverse
polarity protected
Alignment
S3Z…M01
ses
turningincreases
the control
clockwise.
12 … 24 Vdc12
(operating
limit
10…30Vdc);
reverse polarity
protected
Alignment S3Z…M01
Position
theturn
sensor
and turn thescrew
adjus
10…30 VDC
Ripple:
p-p 10% max.
Position the sensor
and
the adjustment
Ripple:
p-p 10% max.
2
4
Place
the target
oppositeatthe
sensor
ONLY(S3Z…B01/C01/C11/F01/T51)
FOR TRIMMER (S3Z…B01/C01/C11/F01/T51)
Place the target
opposite
the sensor
a slightly
Current consumption
MMER
Current consumption
desired.
Turn
the screw counterclockw
30
mA
max.
he
trimmer
rotation
is
limited
to
250°
by
a
mechanical
stop.
desired.
Turn
the
screw
counterclockwise
until
the s
30 mA max.
current excluded):
n is limited to 250° by a mechanical stop.
(output current(output
excluded):
Verify themoving
adjustment
moving
the tar
ye excessive
torque(max
when0.05
adjusting
Verify the adjustment
the target
closer
an
when adjusting
Nm). (max 0.05
1 Nm). Output:
3
Output:
LIGHT;
PNP
tune
the
adjustment
if
necessary.
DARK; PNP DARK; PNP
LIGHT;
PNP
tune
the
adjustment
if
necessary.
LIGHT or DARK;
LIGHT or DARK;
It is recommended
to the
operate
withLED
the
or NPN;
or NPN;
It is recommended
to operate with
stability
or NPN;
or NPN;
LED (S3Z…B01/C01/C11/F01)
C01/C11/F01)
LEDthat
ONthe
indicates
the received
signal has a safety
es
receivedthat
signal
has a safety
ter thanto20%
compared
to the output
mpared
the output
switching
value. switching value.
ONS
INSTALLATION
TALLATION
V
DIMENSIONS
TECHNICAL
TECHNICAL
DATA DATA
PNP or NPN;PNP or NPN;
(short-circuit(short-circuit
(short-circuit (short-circuit
protection) protection)
protection) protection)
TAB.1:
S3Z…B01
max.
operating
di
100 mA max.100 mA max.
TAB.1: S3Z…B01
max.
operating
distance
table
2 V max.
2 V max.
AVAILABLE
R
AVAILABLE REFLECTOR
Response time:
500us max
1 ms max. 1 ms max.
R1
R2
R
S3Z…F01/G00
S3Z…M01
R1
R2
R3
R4
CONNECTIONS
Switching frequency: 1KHz max. 1KHz max.
500 Hz max.
NNECTIONS
Switching
frequency:
500
Hz
max.
ng limit 10…30VDC); (Class 2 UL508) reverse polarity protected
-B01 5 3
5
4.5
-B01
3
4.5
6
Indicators:
OUT LED (YELLOW)
1/C01/C11/F01/M01/T51
Indicators:
OUT LED (YELLOW)
p-p 10% max.
/M01/T51
STABILITY LED (GREEN) mod. B01/C01/C11/F01
STABILITY LED
(GREEN) mod. B01/C01/C11/F01
30mA max. mod.F01
The sensors are NOT safety devices,
35mA max.
POWER ON LED (GREEN) mod. G00
BROWN
The sensors are NOT safety devices, and so MUS
1
safety control of the mac
POWER ON LED (GREEN) mod. G00
WN 15mA
max. mod.G00
1
+ 10 … 30 Vdc
safety control of the machines where i
Vdc
Setting:
6 turns
+ 10 …or30NPN
or DARK; PNP
(short-circuit protection)
Setting:
6 turns
TRIMMER (250°)
DECLARATION
OF CONFORMITY
TRIMMER (250°)
screw
DECLARATION
OF
CONFORMITY
BLACK
100 mA4 max.
screw
We Datalogic Automation declare u
K
We Datalogicthese
Automation
declare
under ourto so
Operating
temperature:
4
OUTPUT
-25
…
+50
°C
products
are conform
V max.
1.5
V max. temperature:
Operating
-25 … +55 °C
OUTPUT
-25 … +50 °C
these products
are conform
to the 2004/10
-25 … +55 °C
successive
amendments.
(UL)
250 us max.
successive amendments.
(UL)
BLUE
Storage temperature:
-40 … +70 °C
2KHz 3max. 0 V
WARRANTY
3
Storage temperature:
-40 … +70 °C
WARRANTY Datalogic Automation warrants its prod
0V
CAUTION
- use of controls
adjustments or performance
of procedures
Operating distance
(minimum):
2m onorR2
50…150
50…250
(YELLOW); STABILITY
LED (GREEN) mod. B01/F01
Datalogic Automation
its products
to be
fre
see
tab.1
0…70
cm
0...20
m
Operating distance (minimum):
2m
on
R2
50…150
50…250
Datalogic
Automation
will repair
or re
other than those specifiedreflector
in this
mannual may result in 0…70
hazardous
Sensorswarrants
mm cm radiation0...20 m CATALOG | Photoelectric
mm.
see
tab.1
Datalogic Automation
repair or during
replace,
o
0 POWER ON LED (GREEN) mod. G00
reflector
mm
mm.
found to will
be defective
thefree
warr
Difference onexposure.
White 90% / Gray
22%found
@ to be defective
mer (250°) BROWN
6 turns screw
duringdate.
the warranty period o
manufacturing
1
--Difference
on
White
90%
/
Gray
22%
@
ATTENTION
L'utilisation
des
commandes,
ainsi
que
les
modifications
de
10
…
30
Vdc
WN
+
manufacturing
date.
18%
200mm.
1 LIGHT/DARK Trimmer
--This warranty does not cover dam
(short-circuit
(short-circuit
positioned
of thethreaded
two housing’s threaded
dcan
by be
means
of the by
twomeans
housing’s
using
twoor
screws
longer or
M2.5 passing screw,
protection) protection)
(M3x12
longer(M3x12
or M2.5orpassing
screw,
Output
current:
ximum
tightening
torque)
with
washers.
Output current:
orque) with washers.
entable tofixing
to ease
the sensor
Output saturation voltage:
ackets
easebrackets
the sensor
positioning
are positioning are
ease refer to the accessories listed in the catalogue).Output saturation voltage:
accessories listed in the catalogue).
Response time:
500us max
DATA
SAFETY PRECAUTIONS
33
CONNECTIONS
INDICATORS AND SETTINGS
DIMENSIONS
S3Z...F01/G00/B01/C01/M01
CABLE
OUTPUT LED
POWER ON LED
(S3Z...G00)
Through beam emitter
BROWN
10...30 Vdc
BROWN
10...30 Vdc
S3Z SERIES
BLACK
OUTPUT
DIMENSIONS
CONNECTIONS
INSTRUCTION MANUAL
BLUE
0V
e EN 60947-5-2 standard.
BLUE
S3Z…G00
BROWN
C
3Z SERIES
1
S3Z
F01/G00
0V
M8 CONNECTOR
+ 10…30
VDC
CONTROLS
M8 CONNECTOR
OUTPUT LED
The yellow LED indicates the output status.
4
1
3TRIMMER
UCTION MANUAL
TECHNICAL DATA
POWER ON LED (S3Z…G00)
10...30 Vdc
0V
Emitter or
Receiver
TRIMMER
S3Z...T51
OUTPUT LED
POWER ON LED
(S3Z...G00)
Receiver
STABILITY LED
STABILITY3 LED (S3Z…B01/C01/C11/F01)
0V
S3Z
S3Z
The green NOT
LED USED
ON indicates that the received
signalB01/C01/C11/M01
has a safety
F01/G00OUTPUT
margin greater(WHITE)
than 20% compared to the output switching
value.
(BLACK)
STABILITY LED
S3Z...T51
DIMENSIONS
S3Z
B01/C01/C11/M01
OUTPUT LED
Emitter or
POWER ON LED
(S3Z...G00) Receiver
2
BLUE
TRIMMER
TRIMMER
Emitter and
Receiver
Coaxial
STABILITY LED
S3Z...T51
Emitter
S3Z...F01/G00/B01/M01/S3Z...-PP, -NN
Receiver
Alignment
Position the
Turn the s
yellow LED
horizontal
points.
Optimum o
If necessar
small or tra
procedure
Alignment
Position the
Find the po
both vertic
between th
Optimum o
The green LED indicates thatS3Z…F01/G00
the sensor is operating.
S3Z…B01
S3Z…M01
Receiver
(BROWN)
(BLUE)
Coaxial
12 …TRIMMER
24 VDC (operating
limit 10…30VDC); (Class 2 UL508) reverse polarity protected
(S3Z…B01/C01/C11/F01/T51)
p-p
10%
max.
CABLE
The trimmer can be used to adjust sensitivity; the operating distance
30mA max. mod.F01
increases
VERSION
35mA
max.turning the trimmer clockwise.
35mA max.
Alignment
15mA max. mod.G00
s the output status.
Position the
ADJUSTMENT
SCREW
(S3Z…M01)
LIGHT
or DARK;
PNP or NPN (short-circuit protection)
S3Z…T51 S3Z…B01 S3Z…C01 S3Z…C11
S3Z
B01/C01/C11/F01)
the green
L
This control can be used to adjust 100
the cutoff
distance (6 turns screw);
mA max.
dicates that the received
hasdistance
a1.5
safety
the pta
V increases
max.
1.5 V max.
thesignal
operating
turning the control clockwise.
Power supply:
12 … 24 Vdc (operating limit 10…30Vdc); Place
reverse
Emitter
% compared to the output switching value.
250 us max.
Ripple:
p-p 10% max. Turn the
yellow LED
2KHz max.
…G00)
WARNING
ONLY FOR TRIMMER (S3Z…B01/C01/C11/F01/T51)
Current consumption CAUTION - use of controls or adjustments or performance of procedures
OUTPUT LED (YELLOW); STABILITY LED (GREEN) mod. B01/F01
Remove th
s that the sensor is operating.
30
max. radiation
MODEL: The trimmer POWER
rotation is ON
limited
to 250°
by a mechanical
stop.
other than those specified in this mannual Dimensions
may result
in mA
hazardous
in mm
(output current excluded):
LED
(GREEN)
mod. G00
clockwise u
exposure.
Do
not
apply
excessive
torque
when
adjusting
(max
0.05
Nm).
Trimmer (250°)
6 turns screw
01/C11/F01/T51)
pos.B).deTh
Output:
DARK;
PNP des commandes, ainsi que les modifications
ATTENTION
L'utilisation
LIGHT or DARK;detected. T
LIGHT/DARK Trimmer
ed to adjust sensitivity; the operating distance
réglages ou de or
procédures
ce
NPN; d’exécution autres que ceux specifiés dans
BACKGROUND SUPPRESSION - -10
DISTANCE
VS REFLECTANCE
… +55DIFFERENCE
°C (-10 … +50
°C UL Listed)TARGET
THROUGH BEAM
DETECTION
mmer clockwise.
PNP or NPN;
two position
mode -d'emploi
peutAREA
entraîner une exposition à des rayonnements
dangereux.
Distance difference vs Reflectance target
(short-circuit
-25
…
+70
°C
no
freezing
or
condesation
This product emits aDetection
visible diagram
laser beam.
Do not (short-circuit
stare into the protection)
beam For
directly.
The sensor can be positioned by means of the two housing’s threaded
S3Z…C
S3Z-F/G
(S3Z…M01) 20,0%
20…250mm
protection)
Furthermore, do
not look the laser
which is reflected
at a mirror-likeoutput
object.
900,00
S3Z…T51 S3Z…B01
S3Z…C01
S3Z…C11
S3Z…F01/G00
S3Z…M01
holes
(M3)
usingscrew);
two
(M3x12
ormlonger or M2.5 passing screw,
are
m
on R2
Whitescrews
90%/Black
6%0...30
White
90%
/ Black
6%
d to adjust the0.3...10
cutoff distance
(6 turns
(white paper 200x200 mm) 800,00
About safety standards of laser product, IEC60825-1 ”Safety of laser products”
Output
100 mA max.
0.5clockwise.
Nm maximum tightening torque)
withsupply:
washers.
10,0%
creases turning
the control
Power
12 …current:
24 Vdc700,00(operating
limitstipulated
10…30Vdc);
polarity protected
has been
by thereverse
IEC (International
Electortechnical Commission).
Alignment
500 Vac 1 min.,
between
electronics and housing
Various orientable fixing brackets to ease the sensor positioning are
600,00
This product is classified as “CLASS1 product” according
to IEC60825-1
Output saturation
voltage:
2 V max.
Position the
Ripple:
p-p 10% max.
>20refer
Mto500
Vdc,
between
and housing
500,00
available (please
the accessories
listedelectronics
in the catalogue).
(2007). Use a UL Listed (CYJV/CYJV7) mating connector/cord assembly when
0,0%
time:400,00 using connector500us
max
1 ms Place
max. the t
--40…300Response
mm
TRIMMER (S3Z…B01/C01/C11/F01/T51)
type
as
UL/c-UL
listed
products.
Current
consumption
300,00
0
50
100
150
200
250
10%Switching frequency:
30-mA
max.
CAUTION
This
Product
200,00
tation is limited
to 250° by a mechanical stop. --1KHz
max. complies with
500 Hzdesired.
max. Tu
(output current excluded):
-10,0%
100,00
Verify the
21 CFR 1040.10 and 1040.11 except for
Ø0.2 mm @ 170 mm
Ø6(max
mm0.05
@3
m
orque when adjusting
Nm).
White
90%/Grey
18%
White
18%
Ø6 mmOutput:
@ 390%
m/ Grey
(opaque)
Indicators:
OUT
LEDPNP
(YELLOW)
0,00
DARK;wire)
PNP
LIGHT;
deviations 5,00
pursuant to Laser
Notice No.
tune the ad
(opaque)
(copper
S3Z…B01/C01/C11/F01/M01/T51
10,00
15,00
20,00
25,00
-100,000,00
LIGHT
or DARK;
-20,0%
50, dated
June
24, 2007, issued
by
STABILITY
LED (GREEN)
Red Laser diode(Emission wavelength: 650nm) or NPN;
It is recomm
-200,00
or NPN; mod. B01/C01/C
CDRH PNP
(Center
of
Devices
and
or NPN;
-300,00
POWER ON
LED (GREEN) mod. G0
BROWN
IEC/JIS
CLASS1
(short-circuit
1 * ; Maximum output: 7mW (short-circuit
-400,00
Radiological
Health)
under
FDA
(Food
10 … 30 Vdc
tioned by means
of the two housing’s threaded
-30,0%
(short-circuit protection)
+ EN
-500,00
according to
60947-5-2
and Drug Administration).
Setting:
protection)
protection)
rews (M3x12 or longer or 0.5
M2.5mm
passing
screw,
-600,00
amplitude, 10 … 55 Hz frequency, for every axis (EN60068-2-6)
ATTENTION
- Ce produit est conforme TRIMMER (250°)
-700,00
Output
current:
100
mA
max.
ning torque) with
washers.
-40,0%
TAB.1: S3Z
aux normes 21 CFR 1040.10 et 1040.11,
BLACK
11 ms (30
G) 6 shock
-800,00
4 for every axis (EN60068-2-27)
g brackets to ease the sensor positioning are BodyOutput
Operating temperature:
-900,00
à l'exception
des
dérogations
No.50 » du
OUTPUT cover
saturation
voltage:
2 -25
V max.
PBT / indicators
PC
…
+50 °C relatives au document « Laser Notice
-25
…
+55
°Cla
24 juin 2007 émis par CDRH (Center of Devices and Radiological Health)
de
the accessories
listed in the catalogue).
[m]
-50,0%
PMMA
(UL)
Response
time:
500us max
1 ms
max.
FDA (Food and Drug
Administration).
White
target ON Distance
(mm)
IP67
BLUE
“Warning
label” and “Certification/-40
Identification
3
Storage temperature: Labels: Following500
… +70 °Clabel” are
Switching
frequency:
1KHz max.
Hz max.
0V
affixed on this product according to IEC 60825-1 and laser regulation -B01
of FDA.
2 m cable  3.5 mm / M8-4
pole connector **
Operating
distance
(minimum):
2m
on
R2
50…150
Indicators:
OUT
LED
(YELLOW)
When
this
product
will
be
incorporated
into
final
device
system which is
50 g. max. cable versions / 10 g. connector versions
F01/M01/T51
see tab.1
0…70 cm
CONTROLS
Emitter and
TECHNICAL DATA
SAFETY PRECAUTIONS
DIAGRAM LED MODELS
TECHNICAL DATA
[mm]
INSTALLATION
CONNECTIONS
NSTALLATION
CONNECTIONS
exported
to- DETECTION
the USA,
make
sure that Certification/Identification
label is affixed.
DIFFUSE PROXIMITY
AREA
reflector
mm
STABILITY
LED (GREEN)
mod.
B01/C01/C11/F01
The senso
The sensors are NOT safety devices, and so MUST NOT be used
POWER
mod. G00
Detection
diagram S3Z-C
Difference on White
90% / ON
GrayLEDin(GREEN)
the safety control of the machines where
--- installed.
20
10
…
30
Vdc
+
18%
Setting:
6 turns
140,00
R5
DECLARATION
TRIMMER
(250°)OF CONFORMITY
SETTING
120,00
DECLARA
15
screw INFRARED
RED
RED
We
Datalogic
Automation
declare
under
our
sole
responsibility
that these IN
100,00
LACK
We Datalo
Emission type:
4 80,00
Alignment S3Z…M01
products are (650
conform
to the 2004/108/EC
Directive and
successive
nm)
(665
nm)
(850
nm)
Operating
temperature:
OUTPUT
-25photoelectric
… +50 °C sensor 10
these pro
amendments.
posite sides. 60,00
Referring to the table below, adjust the distance of the
-25 … +55 °C
Ambient
light
according to EN 60947-5-2
R2 explains the status of operation
successive
(UL)
m. Find the points
when necessary. The table
LED
when
therejection:
40,00 where
WARRANTY
5
20,00
LUE
nd OFF in3 both
vertical
operation mode
is setStorage
to light temperature:
ON.
Datalogic-40
Automation
products to
fromfrequency,
defects. for every a
Vibration:
0.5 mm its
amplitude,
10be…free
55 Hz
BLUE
… +70 °Cwarrants
WARRANT
3
0,000 V
Datalogic Automation will repair or replace, free of charge, any product
found
0
e sensor in the
centre
0V
Distance
Shock
resistance:
11
ms
(30
G)
6
shock
for
every
(EN600
1000 Step 2000
3000
4000
5000
6000
7000
8000
-20,00 0
Datalogic
Adjusting procedure
0
100be defective
200
300during400 the 500
600 period
700 of50…250
800 months
900 axis
1000
Operating
distance
(minimum):
2m
on
R2
50…150
to
warranty
36
from
the A
ion is obtained when the
control
-40,00
see
tab.1
0…70
cm
0...20
m
-5
manufacturing
date. This warranty does not cover
damage
or liability
deriving A
Datalogic
LIGHT/DARK selection:
dependently
from
the model
reflector
mm
mm.
-60,00
Install a photoelectric sensor and the sensing
from the improper application of Datalogic Automation products.
found to be
the trimmer, -80,00
in orderCONNETTORE
to
M8
PNP/NPN
dependently
Difference
White
/ Gray
22% @from the model
object.on
Turn
the90%
control
counter-clockwise
until Output
the -10
DATALOGIC AUTOMATION srl
ROWN
ets.
In order
to improve
manufactur
1 -100,00
--1
30 Vdc
Via Lavino 265 - 40050 Monte S.Pietro - Body
Bologna
Italy
+ 10 …whilst
Housing: until -15
PC–and
PBT / indicators
18%operation LED turns OFF. Then turn clockwise
200mm.
-120,00
detailed above
Thiscover
warraP
Tel: +39 051 6765611 - Fax: +39 051 6759324
www.datalogic.com
the operation
LED turns ON (point A).
-140,00
2
4
Lenses:
PMMA
PC
PMMA
improper
a
RED
RED
INFRARED
INFRARED
RED
-20
[mm]
Under current Italian and European laws, Datalogic Automation is not obliged
Emission type:
nm) disposal(870
ProtectionLED
class:(665 nm) to take care(850
IP67
Remove the sensing object, then(650
the nm)
operation
of product
at thenm)
end of its life.(670 nm)
DATALOG
[mm]
1
Datalogic Automation Recommends to dispose of the product in compliance with
turns3
OFF.
Turn clockwise until the operation
LED
Via Lavino
2
Ambient
light
rejection:
according
EN 60947-5-2
Connections:
m cablecentres.
3.5 mm
/ M8-4
pole
conne
local laws ortocontact
authorised waste 2collection
Datalogic
Automation
turns ON, the background is detected (point B).
+39 05
reserves
the
right to for
make
modifications
and improvements withoutTel:
prior
OUT)
ON and
Vibration:
0.5
mm
amplitude,
10
…
55
Hz
frequency,
every
axis
(EN60068-2-6)
LUE is switched
Weight:
50
g.
max.
cable
versions
/
10
g.
connector
3
notification.
tions, and fix the 0sensor
V
Unde
Shock resistance:
11 ms (30 G)
6 shock
for Datalogic
every axis
(EN60068-2-27)
© 2012
– 2015
Automation
- ALL RIGHTS RESERVED - Protected to the
to tak
fullest extent under U.S. and international laws. • Copying, or altering of this document
Set
the
middle
point
between
point
A
and
B
as
LIGHT/DARK selection:
fromexpress
the model
e green LED is ON.
Datalogic
isdependently
prohibited without
written consent from Datalogic Automation. Datalogic
and A
3
point C.
local laws
the
Datalogic logo
arethe
registered
trademarks of Datalogic S.p.A. in many countries,
PNP/NPN
Output
dependently
from
model
34 CATALOG | Photoelectric Sensors
including the U.S.A. and the E.U.
reserves th
Housing:
Body PC and PBT / indicators 821003301
cover PC
notification.
Rev. B
2
[mm]
[mm]
POLARIZED RETROREFLECTIVE - DETECTION AREA
S3Z…G00
egulations 21CFR 1040.10
and 1040.11 based on Notice No.50.
ROWN
1
BROWN
Detection
diagram
ating connector/cord
assembly
when using
connector
as UL/c-UL listed products.
1 typeS3Z-B
10
…
30
Vdc
+
POLARIZED RETROREFLECTIVE FOR TRANSPARENT - DETECTION AREA
NARROW BEAM PROXIMITY - DETECTION AREA
mm
mm
m
mm
DIAGRAMS LASER MODELS
BACKGROUND SUPPRESSION - DETECTION AREA
BACKGROUND SUPPRESSION - SPOT DIMENSION
mm
mm
3
Black 6%
2.5
1
Spot size (mm)
Lateral Displacement Y (mm)
2
0
-1
-2
-3
Background Suppression Spot size (Typical)
3.0
100
200
Sensing Distance X (mm)
1.5
Lateral direction
1.0
0.5
White 90%
0
2.0
mm
300
400
0.0
mm
Axial direction
0
50
100
150
200
250
300
350
400
450
500
Distance (mm)
POLARIZED RETROREFLECTIVE - DETECTION AREA
POLARIZED RETROREFLECTIVE - EXCESS GAIN
100
mm
15
R5
5
Excess Gain
Lateral Displacement Y (mm)
10
R2
0
R5
10
R2
-5
m
-10
-15
0
1
2
3
4
5
6
7
8
9
10
m
Operation 1
level 0
5
Sensing Distance X (m)
THROUGH BEAM - DETECTION AREA
10
15
20
Sensing Distance (m)
THROUGH BEAM - EXCESS GAIN
mm
100
30
10
Excess Gain
Lateral Displacement Y (mm)
20
0
10
-10
m
-20
-30
0
5
10
15
20
25
30
Sensing Distance X (m)
35
40
45
50
m
Operation
1
level 0
10
20
30
40
50
Sensing Distance X (m)
CATALOG | Photoelectric Sensors
35
MODEL SELECTION AND ORDER INFORMATION
OPTIC FUNCTION
EMISSION
Narrow beam diffuse proximity
LED
Long diffuse proximity
LED
LED
Polarized retroreflective
LASER
LED
Through beam
LASER
LED
Background suPression
LASER
Polarized retroreflective
for transparent
36
CATALOG | Photoelectric Sensors
LED
CONNECTION
2 m Cable
M8 Connector
2 m Cable
M8 Connector
2 m Cable
M8 Connector
2 m Cable
M8 Connector
2 m Cable
M8 Connector
2 m Cable
M8 Connector
2 m Cable
M8 Connector
2 m Cable
M8 Connector
2 m Cable
M8 Connector
2 m Cable
M8 Connector
2 m Cable
M8 Connector
2 m Cable
M8 Connector
2 m Cable
M8 Connector
2 m Cable
M8 Connector
2 m Cable
M8 Connector
2 m Cable
M8 Connector
2 m Cable
M8 Connector
2 m Cable
M8 Connector
2 m Cable
M8 Connector
2 m Cable
M8 Connector
2 m Cable
M8 Connector
2 m Cable
M8 Connector
2 m Cable
M8 Connector
2 m Cable
M8 Connector
2 m Cable
M8 Connector
2 m Cable
M8 Connector
2 m Cable
M8 Connector
2 m Cable
M8 Connector
2 m Cable
M8 Connector
2 m Cable
M8 Connector
2 m Cable
M8 Connector
2 m Cable
M8 Connector
2 m Cable
M8 Connector
2 m Cable
M8 Connector
2 m Cable
2 m Cable
M8 Connector
M8 Connector
OUTPUT
PNP - LIGHT
PNP - LIGHT
PNP - DARK
PNP - DARK
NPN - LIGHT
NPN - LIGHT
NPN - DARK
NPN - DARK
PNP - LIGHT/DARK
PNP - LIGHT/DARK
NPN - LIGHT/DARK
NPN - LIGHT/DARK
PNP - LIGHT
PNP - LIGHT
PNP - DARK
PNP - DARK
NPN - LIGHT
NPN - LIGHT
NPN - DARK
NPN - DARK
PNP - LIGHT/DARK
PNP - LIGHT/DARK
NPN - LIGHT/DARK
NPN - LIGHT/DARK
PNP - LIGHT
PNP - LIGHT
PNP - DARK
PNP - DARK
NPN - LIGHT
NPN - LIGHT
NPN - DARK
NPN - DARK
PNP - LIGHT/DARK
PNP - LIGHT/DARK
NPN - LIGHT/DARK
NPN - LIGHT/DARK
PNP - LIGHT/DARK
PNP - LIGHT/DARK
NPN - LIGHT/DARK
NPN - LIGHT/DARK
PNP - LIGHT
PNP - LIGHT
PNP - DARK
PNP - DARK
NPN - LIGHT
NPN - LIGHT
NPN - DARK
NPN - DARK
PNP - LIGHT/DARK
PNP - LIGHT/DARK
NPN - LIGHT/DARK
NPN - LIGHT/DARK
PNP - LIGHT/DARK
PNP - LIGHT/DARK
NPN - LIGHT/DARK
NPN - LIGHT/DARK
PNP - LIGHT
PNP - LIGHT
NPN - LIGHT
NPN - LIGHT
PNP - LIGHT/DARK
PNP - LIGHT/DARK
NPN - LIGHT/DARK
NPN - LIGHT/DARK
PNP - LIGHT/DARK
PNP - LIGHT/DARK
NPN - LIGHT/DARK
NPN - LIGHT/DARK
NPN - DARK
PNP - DARK
NPN - DARK
PNP - DARK
MODEL
S3Z-PR-2-C01-PL
S3Z-PR-5-C01-PL
S3Z-PR-2-C01-PD
S3Z-PR-5-C01-PD
S3Z-PR-2-C01-NL
S3Z-PR-5-C01-NL
S3Z-PR-2-C01-ND
S3Z-PR-5-C01-ND
S3Z-PR-2-C01-PP
S3Z-PR-5-C01-PP
S3Z-PR-2-C01-NN
S3Z-PR-5-C01-NN
S3Z-PR-2-C11-PL
S3Z-PR-5-C11-PL
S3Z-PR-2-C11-PD
S3Z-PR-5-C11-PD
S3Z-PR-2-C11-NL
S3Z-PR-5-C11-NL
S3Z-PR-2-C11-ND
S3Z-PR-5-C11-ND
S3Z-PR-2-C11-PP
S3Z-PR-5-C11-PP
S3Z-PR-2-C11-NN
S3Z-PR-5-C11-NN
S3Z-PR-2-B01-PL
S3Z-PR-5-B01-PL
S3Z-PR-2-B01-PD
S3Z-PR-5-B01-PD
S3Z-PR-2-B01-NL
S3Z-PR-5-B01-NL
S3Z-PR-2-B01-ND
S3Z-PR-5-B01-ND
S3Z-PR-2-B01-PP
S3Z-PR-5-B01-PP
S3Z-PR-2-B01-NN
S3Z-PR-5-B01-NN
S3Z-PH-2-B01-P
S3Z-PH-5-B01-P
S3Z-PH-2-B01-N
S3Z-PH-5-B01-N
S3Z-PR-2-FG01-PL
S3Z-PR-5-FG01-PL
S3Z-PR-2-FG01-PD
S3Z-PR-5-FG01-PD
S3Z-PR-2-FG01-NL
S3Z-PR-5-FG01-NL
S3Z-PR-2-FG01-ND
S3Z-PR-5-FG01-ND
S3Z-PR-2-FG01-PP
S3Z-PR-5-FG01-PP
S3Z-PR-2-FG01-NN
S3Z-PR-5-FG01-NN
S3Z-PH-2-FG01-P
S3Z-PH-5-FG01-P
S3Z-PH-2-FG01-N
S3Z-PH-5-FG01-N
S3Z-PR-2-M01-PL
S3Z-PR-5-M01-PL
S3Z-PR-2-M01-NL
S3Z-PR-5-M01-NL
S3Z-PR-2-M01-PP
S3Z-PR-5-M01-PP
S3Z-PR-2-M01-NN
S3Z-PR-5-M01-NN
S3Z-PH-2-M01-P
S3Z-PH-5-M01-P
S3Z-PH-2-M01-N
S3Z-PH-5-M01-N
S3Z-PR-2-T51-ND
S3Z-PR-2-T51-PD
S3Z-PR-5-T51-ND
S3Z-PR-5-T51-PD
ORDER
NO.
95B010040
95B010050
95B010060
95B010070
95B010200
95B010210
95B010220
95B010230
95B010670
95B010690
95B010660
95B010680
95B010001
95B010011
95B010021
95B010031
95B010161
95B010171
95B010181
95B010191
95B010630
95B010650
95B010620
95B010640
95B010081
95B010091
95B010101
95B010111
95B010241
95B010251
95B010261
95B010271
95B010590
95B010610
95B010580
95B010600
95B010440
95B010460
95B010450
95B010470
95B010121
95B010131
95B010141
95B010151
95B010281
95B010291
95B010301
95B010311
95B010710
95B010730
95B010700
95B010720
95B010520
95B010540
95B010530
95B010550
95B010331
95B010351
95B010321
95B010341
95B010750
95B010770
95B010740
95B010760
95B010480
95B010500
95B010490
95B010510
95B010390
95B010380
95B010370
95B010360
ACCESSORIES
ST-505
ST-5046
ST-5039
ST-5040
SLIT
M18 ADAPTER NOSE
MODEL SELECTION AND ORDER INFORMATION
MODEL
DESCRIPTION
ST-505
ST-5039
ORDER NO.
lateral mounting
L-shaped fixing bracket
protection bracket with vertical fixing
(only for cable versions)
protection bracket with horizontal fixing
Ø 0,5 mm slit for through beam
Ø 1 mm slit for through beam
Ø 2 mm slit for through beam
0,5x18 mm slit for through beam
1x18 mm slit for through beam
2x18 mm slit for through beam
S3Z FIX BRK M18 THREADED NOSE
ST-5040
ST-5046
S3Z-SLIT1
S3Z-SLIT2
S3Z-SLIT3
S3Z-SLIT4
S3Z-SLIT5
S3Z-SLIT6
ST-S3Z-M18
95ACC2800
95ACC2270
95ACC2280
95ACC2370
95ACC2470
95ACC2480
95ACC2490
95ACC2500
95ACC2510
95ACC2520
95ACC7850
CABLES
TYPE
DESCRIPTION
Axial M8 Connector
4-pole, grey, P.V.C.
4-pole, P.U.R.
Radial M8 Connector
4-pole, grey, P.V.C.
4-pole, P.U.R.
LENGTH
MODEL
3m
5m
7m
10 m
2m
5m
3m
5m
7m
10 m
2m
5m
CS-B1-02-G-03
CS-B1-02-G-05
CS-B1-02-G-07
CS-B1-02-G-10
CS-B1-02-R-02
CS-B1-02-R-05
CS-B2-02-G-03
CS-B2-02-G-05
CS-B2-02-G-07
CS-B2-02-G-10
CS-B2-02-R-02
CS-B2-02-R-05
ORDER No.
95A251420
95A251430
95A251440
95A251480
95A251620
95A251640
95A251450
95A251460
95A251470
95A251530
95A251630
95A251650
Rev. 03, 03/2019
DATALOGIC PRODUCT OFFERING
Sensors
Hand Held
scanners
Mobile Computers
Laser Marking
Systems
Safety Laser
Scanner
Vision
Systems
Stationary
Industrial
Scanners
Safety Light
Curtains
The company endeavours to continuously improve and renew its products; for this reason the technical data and contents of this catalogue may undergo variations without prior notice. For correct installation and use,
the company can guarantee only the data indicated in the instruction manual supplied with the products. Product and Company names and logos referenced may be either trademarks or registered trademarks of their
respective companies. We reserve the right to make modifications and improvements.
37