Datalogic Lynx Handheld Computer Owner's Manual

Datalogic S.r.l.

Via S. Vitalino, 13

40012 Calderara di Reno

Italy

Tel. +39 051 3147011

Fax +39 051 3147205

©2017 Datalogic S.p.A. and/or its affiliates

 All rights reserved.  Without limiting the rights under copyright, no part of this documentation may be reproduced, stored in or introduced into a retrieval system, or transmitted in any form or by any means, or for any purpose, without the express written permission of Datalogic S.p.A. and/or its affiliates. Owners of Datalogic products are hereby granted a non-exclusive, revocable license to reproduce and transmit this documentation for the purchaser's own internal business purposes. Purchaser shall not remove or alter any proprietary notices, including copyright notices, contained in this documentation and shall ensure that all notices appear on any reproductions of the documentation.

Should future revisions of this manual be published, you can acquire printed versions by contacting your Datalogic representative. Electronic versions may either be downloadable from the Datalogic website ( www.datalogic.com

) or provided on appropriate media. If you visit our website and would like to make comments or suggestions about this or other Datalogic publications, please let us know via the "Contact Datalogic" page.

Disclaimer

Datalogic has taken reasonable measures to provide information in this manual that is complete and accurate, however,

Datalogic reserves the right to change any specification at any time without prior notice.

Datalogic and the Datalogic logo are registered trademarks of Datalogic S.p.A. in many countries, including the U.S.A.

and the E.U. Lynx is a trademark of Datalogic S.p.A. and/or its affiliates, registered in many countries, including the U.S.

and the E.U. All other trademarks and brands are property of their respective owners.

Patents

See www.patents.datalogic.com

for patent list.

This product is covered by one or more of the following patents:

Design patents: EP001711946, USD633502, ZL201030189483.7.

Waste Electrical and Electronic Equipment (WEEE)

Information for the User

At the end of its useful life, the product marked with the crossed out wheeled wastebin must be disposed of separately from urban waste.

For more detailed information about disposal, contact the supplier that provided you with the product in question or consult the dedicated section at the website http://www.datalogic.com

.

Informazione per gli utenti

L’apparecchiatura che riporta il simbolo del bidone barrato deve essere smaltita, alla fine della sua vita utile, separatamente dai rifiuti urbani.

Per maggiori dettagli sulle modalità di smaltimento, contattare il Fornitore dal quale è stata acquistata l’apparecchiatura o consultare la sezione dedicata sul sito http://www.datalogic.com

.

Information aux utilisateurs

Au terme de sa vie utile, le produit qui porte le symbole d'un caisson à ordures barré ne doit pas être éliminé avec les déchets urbains.

Pour obtenir des informations complémentaires concernant l'élimination, veuillez contacter le fournisseur auprès duquel vous avez acheté le produit ou consulter la section consacrée au site web http://www.datalogic.com

.

Benutzerinformation bezüglich

Am Ende des Gerätelebenszyklus darf das Produkt nicht über den städtischen Hausmüll entsorgt werden. Eine entsprechende

Mülltrennung ist erforderlich.

Weitere Informationen zu dieser Richtlinie erhalten sie von ihrem Lieferanten über den sie das Produkt erworben haben, oder besuchen sie unsere Hompage unter http://www.datalogic.com

.

Información para el usuario

Al final de su vida útil, el producto marcado con un simbolo de contenedor de bassura móvil tachado no debe eliminarse junto a los desechos urbanos.

Para obtener una información más detallada sobre la eliminación, por favor, póngase en contacto con el proveedor donde lo compró o consultar la sección dedicada en el Web site http://www.datalogic.com

.

Accessories

The device has some accessories (e.g: Single Slot Dock, 4 Slot Docks etc). For further details about the models, refer to the Datalogic web site: www.datalogic.com

.

•

•

•

•

Dock, Single Slot

1

Charger, 4 Slot Dock

2

Dock, Ethernet 4 Slot

2

Charger, 4 Slot Battery

2

CAUTION

•

•

•

•

•

•

•

Before using the accessories, read this Safety Addendum carefully.

Use only the components (spare batteries etc) supplied by the manufacturer for the specific Lynx's accessories being used.

Do not attempt to disassemble the accessories device, as it does not contain parts that can be repaired by the user. Any tampering will invalidate the warranty.

Do not submerge the accessories and any other their parts in liquid products.

For further information or support, refer to the Datalogic web site: www.datalogic.com.

1. Power Supply

This device is intended to be connected to a UL Listed/CSA Certified Power Unit marked “Class 2” or LPS power source rated 5 V, 3A. The package may

include international plug adapters. The adapters must be plugged in the power supply before the power supply itself is plugged on the wall outlet.

2. Power Supply

This device is intended to be connected to a UL Listed/CSA Certified Power Unit marked “Class 2” or LPS power source rated 12 V, 5A. The package may

include international plug adapters. The adapters must be plugged in the power supply before the power supply itself is plugged on the wall outlet.

Lynx™

Mobile Computer

Safety & Regulatory Addendum

852000961 (Rev. A) June 2017

This document is an addendum to the Quick

Start Guide (QSG) for this product. See the QSG for additional product information.

©2017 Datalogic S.p.A. and/or its affiliates  All rights reserved. Datalogic and the Datalogic logo are registered trademarks of Datalogic S.p.A. in many countries, including the U.S.A. and the E.U.

www.datalogic.com

Read carefully the Lynx user manual (available at www.datalogic.com

) before performing any type of connection to the Lynx.

The user is responsible for any damage caused by incorrect use of the equipment or by inobservance of the indication supplied in the user manual.

NOTE

General Safety Rules

CAUTION

•

•

•

•

•

•

•

Before using the devices and the battery packs, read this Addendum carefully.

Use only the components and accessories supplied by the manufacturer for the specific Lynx being used.

Do not attempt to disassemble the Lynx device, as it does not contain parts that can be repaired by the user. Any tampering will invalidate the warranty.

When replacing the battery pack or at the end of the operative life of the

Lynx device, disposal must be performed in compliance with the laws in force in your jurisdiction.

Do not submerge the Lynx in liquid products.

For further information or support, refer to the Datalogic web site: www.datalogic.com

.

Power Supply

This device is intended to be connected to a UL Listed/CSA Certified computer which supplies power directly to the Lynx or else be supplied by a UL Listed/CSA Certified Power Unit marked “Class 2” or LPS power source rated 5 V, 1.8 A, which supplies power directly to the Lynx via the power connector of the cable.

The package may include international plug adapters. The adapters must be plugged in the power supply before the power supply itself is plugged on the wall outlet.

Battery Information

Do not incinerate, disassemble, short terminals, or expose to high temperature. Risk of fire and explosion. Use specified charger only. Risk of explosion if the battery is replaced by an incorrect type. Dispose of batteries as required by local authorities.

CAUTION

By default, the main battery pack is disconnected at the factory to avoid damage due to excessive draining.

Rechargeable backup batteries and battery packs are not initially charged. Charge the battery pack as indicated in the Quick Start Guide or in the User Manual, before using the Lynx terminal.

The battery pack autonomy varies according to many factors, such as the frequency of barcode scanning,

RF usage, battery life, storage, environmental conditions, etc.

Use only a USB-IF compliant USB port as a charging source.

The batteries should be charged at a temperature ranging from 0° to +44 °C (+33.8° to +111.2 °F) to achieve the maximum charging rate.

Never charge the main device or the spare batteries in a closed space where excessive heat can build up.

As a safety precaution, the battery may stop charging to avoid overheating.

The Lynx may get warm during charging; this is normal and does not mean a malfunction.

Even if the storage temperature range is wider, it is recommended to store the terminal and the spare batteries at a temperature ranging from 20 to 30 ºC (68 to 86 ºF), in order to achieve the longest battery life.

To maximize battery life, turn off radios when they are not needed.

CAUTION

Do not use the Lynx until standard batteries are charged for minimum 4 hours and extended batteries are charged for minimum 6 hours.

Avoid storing batteries for long periods in a state of full charge or very low charge.

We recommend charging the battery pack every two to three months to keep its charge at a moderate level to maximize battery life.

Annual replacement of rechargeable battery pack avoids possible risks or abnormalities and ensures maximum performance.

WARNING

Use only Datalogic approved batteries and accessories for battery charging.

Risk of explosion if battery is replaced by an incorrect type.

Dispose of used batteries according to the instructions.

Il y a risque d’explosion si la batterie est remplacée par une batterie de type incorrect.

Mettre au rebut les batteris usagées confor mément aux instructions.

Battery Safety Guidelines

WARNING

Installing, charging and/or any other action should be done by authorized personnel and following this manual.

The battery pack may get hot, explode, ignite, and/or cause serious injury if exposed to abusive conditions.

If the battery pack is replaced with an improper type, there is risk of explosion.

Do not place the battery pack in or near a fire or other heat source; do not place the battery pack in direct sunlight, or use or store the battery pack inside unventilated areas in hot weather; do not place the battery pack in microwave ovens, in clothes dryers, in high pressure containers, on induction cook surfaces or similar devices. Doing so may cause the battery pack to generate heat, explode or ignite. Using the battery pack in this manner may also result in a loss of performance and a shortened life expectancy.

Use only a Datalogic approved power supply. The use of an alternative power supply will void the product warranty, may cause product damage and may cause heat, an explosion, or fire.

The area in which the units are charged should be clear of debris and combustible materials or chemicals.

Do not use the battery pack of this terminal to power devices other than this device.

Immediately discontinue use of the battery pack if, while using, charging or storing the battery pack, the battery pack emits an unusual smell, feels hot, changes colour or shape, or appears abnormal in any other way.

Do not short-circuit the battery pack contacts connecting the positive terminal and negative terminal. This might happen, for example, when you carry a spare battery pack in your pocket or purse; accidental short–circuiting can occur when a metallic object such as a coin, clip, or pen causes direct connection of the contacts of the battery pack (these look like metal strips on the battery pack). Short–circuiting the terminals may damage the battery pack or the connecting object.

Do not apply voltages to the battery pack contacts.

Do not pierce the battery pack with nails, strike it with a hammer, step on it or otherwise subject it to strong impacts, pressures, or shocks.

Do not disassemble or modify (i.e. bend, crush or deform) the battery pack. The battery pack contains safety and protection devices, which, if damaged, may cause the battery pack to generate heat, explode or ignite.

In case of leakage of liquid from the battery, avoid contact with liquid the skin or eyes. If the contact occurs, immediately wash the affected area with water and consult a doctor.

Do not solder directly onto the battery pack.

Do not expose the battery pack to liquids.

WARNING

Avoid any knocks or excessive vibrations. If the device or the battery is dropped, especially on a hard surface, you should take it to the nearest Authorised Repair Centre for inspection before continuing to use it.

If your device stops working for any reason, do not use its battery on other electronic devices without a prior check and approval by an Authorised Repair Centre.

Do not replace the battery pack when the device is turned on.

Do not remove or damage the battery pack’s label.

Do not use the battery pack if it is damaged in any part.

Battery pack usage by children should be supervised.

Collect and recycle waste batteries separately from the device in compliance with European

Directive 2006/66/EC, 2011/65, 2002/96/EC and subsequent modifications, with US and

China regulatory laws and regulations about the environment.

Wireless and Radio Frequencies Warnings

WARNING

Use only the supplied or an approved replacement antenna. Unauthorized antennas, modifications or attachments could damage the product and may violate laws and regulations.

Most modern electronic equipment is shielded from RF signals. However, certain electronic equipment may not be shielded against the RF signals generated by Lynx.

Datalogic recommends persons with pacemakers or other medical devices to follow the same recommendations provided by Health Industry Manufacturers Associations for mobile phones.

Persons with pacemakers:

•

•

•

•

Should ALWAYS keep this device more than twenty five (25) cm from their pacemaker and/or any other medical device;

Should not carry this device in a breast pocket;

Should keep the device at the opposite side of the pacemaker and/or any other medical device;

Should turn this device OFF or move it immediately AWAY if there is any reason to suspect that interference is taking place.

Should ALWAYS read pacemaker or any other medical device guides or should • consult the manufacturer of the medical device to determine if it is adequately shielded from external RF energy.

In case of doubt concerning the use of wireless devices with an implanted medical device, contact your doctor.

Turn this device OFF in health care facilities when any regulations posted in these areas instruct you to do so. Hospitals or health care facilities may use equipment that could be sensitive to external RF energy.

RF signals may affect improperly installed or inadequately shielded electronic systems in motor vehicles. Check with the manufacturer or its representative regarding your vehicle. You should also consult the manufacturer of any equipment that has been added to your vehicle.

An air bag inflates with great force. DO NOT place objects, including either installed or portable wireless equipment, in the area over the air bag or in the air bag deployment area. If a vehicle’s wireless equipment is improperly installed and the air bag inflates, serious injury could result.

Turn off the device when in any area with a potentially explosive atmosphere. Observe restrictions and follow closely any laws, regulations, warnings and best practices on the use of radio equipment near fuel storage areas or fuel distribution areas, chemical plants or where any operation involves use of explosive materials.

Do not store or carry flammable liquids, explosive gases or materials with the device or its parts or accessories.

Areas with a potentially explosive atmosphere are often, but not always, clearly marked or shown.

Sparks in such areas could cause an explosion or fire, resulting in injury or even death.

Laser Safety

This information applies to both laser models and the Lynx Imager Aiming System.

The laser light is visible to the human eye and is emitted from the window indicated in the figure.

LASER LIGHT - DO NOT STARE INTO BEAM; CLASS 2 LASER PRODUCT; MAX OUTPUT RADIATION 1 mW;

EMITTED WAVE LENGTH 630~680 nm; COMPLIANT WITH EN 60825-1 (2014)

The artwork below may be only a draft. Please refer to the label attached to the product for information about certification marks.

NOTE

Laser Safety Label

Scan Window

Address Label

Regulatory Label

ITALIANO DEUTSCH FRANÇAIS ESPAÑOL

LA LUCE LASER È VISIBILE

ALL'OCCHIO UMANO E VIENE

EMESSA DALLA FINESTRA

INDICATA NELLA FIGURA.

DIE LASER-STRAHLUNG IST

FÜR DAS MENSCHLICHE

AUGE SICHTBAR UND WIRD

AM STRAHLAUS

LE RAYON LASER EST

VISIBLE À L'OEIL NU ET IL

EST ÉMIS PAR LA FENÊTRE

DÉSIGNÉE SUR

TRITTSFENSTER L'ILLUSTRATION DANS LA

AUSGESENDET (SIEHE BILD).

FIGURE.

A LUZ LÁSER ES VISIBLE AL

OJO HUMANO Y ES EMITIDA

POR LA VENTANA INDICADA

EN LA FIGURA.

LUCE LASER NON FISSARE IL LASERSTRAHLUNG NICHT IN

FASCIO

APPARECCHIO LASER DI

DEN STRAHL BLICKEN

PRODUKT DER

RAYON LASER EVITER DE

REGARDER LE RAYON

RAYO LÁSER NO MIRAR FIJO

EL RAYO APARATO LÁSER

APPAREIL LASER DE CLASSE DE CLASE 2 MÁXIMA

CLASSE 2 MASSIMA

POTENZA D'USCITA: 1 mW

LUNGHEZZA D'ONDA

EMESSA: 630~680 nm

CONFORME A EN 60825-1

(2014).

LASERKLASSE 2 MAXIMALE

AUSGANGSLEISTUNG: 1 mW

WELLENLÄGE: 630~680 nm

ENTSPR. EN 60825-1 (2014).

2 PUISSANCE DE SORTIE: 1 mW

LONGUEUR D'ONDE EMISE:

630~680 nm

CONFORME A EN 60825-1

(2014).

POTENCIA DE SALIDA: 1 mW

LONGITUD DE ONDA

EMITIDA: 630~680 nm

CONFORME A EN 60825-1

(2014).

ENGLISH

The following information is provided to comply with the rules imposed by international authorities and refers to the correct use of your device.

STANDARD LASER SAFETY REGULATIONS

This product conforms to the applicable requirements of both CDRH 21 CFR 1040 and EN 60825-1 at the date of manufacture.

For installation, use and maintenance, it is not necessary to open the device.

WARNING

Do not attempt to open or otherwise service any components in the optics cavity. Opening or servicing any part of the optics cavity by unauthorized personnel may violate laser safety regulations. The optics system is a factory only repair item.

Use of controls or adjustments or performance of procedures other than those specified herein may result in exposure to hazardous visible laser light.

Use of optical systems with the scanner will increase eye hazard. Optical instruments include binoculars, microscopes, eye glasses and magnifying glasses.

The product utilizes a low-power laser diode. Although staring directly at the laser beam momentarily causes no known biological damage, avoid staring at the beam as one would with any very strong light source, such as the sun. Avoid that the laser beam hits the eye of an observer, even through reflective surfaces such as mirrors, etc.

ITALIANO

Le seguenti informazioni vengono fornite dietro direttive delle autorità internazionali e si riferiscono all’uso corretto del terminale.

NORMATIVE STANDARD PER LA SICUREZZA LASER

Questo prodotto risulta conforme alle normative vigenti sulla sicurezza laser alla data di produzione: CDRH 21 CFR 1040 e EN 60825-1.

Non si rende mai necessario aprire l’apparecchio per motivi di installazione, utilizzo o manutenzione.

ATTENZIONE

Non tentare di accedere allo scomparto contenete i componenti ottici o di farne la manutenzione.

L’apertura dello scomparto, o la manutenzione di qualsiasi parte ottica da parte di personale non autorizzato, potrebbe violare le norme della sicurezza. Il sistema ottico può essere riparato solamente alla fabbrica.

L'utilizzo di procedure o regolazioni differenti da quelle descritte nella documentazione può provocare un'esposizione pericolosa a luce laser visibile.

L’uso di strumenti ottici assieme allo scanner può aumentare il pericolo di danno agli occhi. Tali strumenti ottici includono cannocchiali, microscopi, occhiali e lenti di ingrandimento.

Il prodotto utilizza un diodo laser a bassa potenza. Sebbene non siano noti danni riportati dall’occhio umano in seguito ad una esposizione di breve durata, evitare di fissare il raggio laser così come si eviterebbe qualsiasi altra sorgente di luminosità intensa, ad esempio il sole. Evitare inoltre di dirigere il raggio laser negli occhi di un osservatore, anche attraverso superfici riflettenti come gli specchi.

DEUTSCH

Die folgenden Informationen stimmen mit den Sicherheitshinweisen überein, die von internationalen Behörden auferlegt wurden, und sie beziehen sich auf den korrekten Gebrauch vom Terminal.

NORM FÜR DIE LASERSICHERHEIT

Dies Produkt entspricht am Tag der Herstellung den gültigen EN 60825-1 und CDRH 21 CFR 1040 Normen für die Lasersicherheit.

Es ist nicht notwendig, das Gerät wegen Betrieb oder Installations- und Wartungs-Arbeiten zu öffnen.

ACHTUNG

Unter keinen Umständen darf versucht werden, die Komponenten im Optikhohlraum zu öffnen oder auf irgendwelche andere Weise zu warten. Das Öffnen bzw. Warten der Komponenten im Optikhohlraum durch unbefugtes Personal verstößt gegen die Laser-

Sicherheitsbestimmungen. Das Optiksystem darf nur werkseitig repariert werden.

Jegliche Änderungen am Gerät sowie Vorgehensweisen, die nicht in dieser Betriebsanleitung beschrieben werden, können ein gefährliches

Laserlicht verursachen.

Die Verwendung von Optiksystemen mit diesem Scanner erhöht die Gefahr einer Augenbeschädigung. Zu optischen Instrumenten gehören unter anderem Ferngläser, Mikroskope, Brillen und Vergrößerungsgläser.

Der Produkt benutzt eine Laserdiode. Obwohl zur Zeit keine Augenschäden von kurzen Einstrahlungen bekannt sind, sollten Sie es vermeiden für längere Zeit in den Laserstrahl zu schauen, genauso wenig wie in starke Lichtquellen (z.B. die Sonne). Vermeiden Sie es, den Laserstrahl weder gegen die Augen eines Beobachters, noch gegen reflektierende Oberflächen zu richten.

FRANÇAIS

Les informations suivantes sont fournies selon les règles fixées par les autorités internationales et se réfèrent à une correcte utilisation du terminal.

NORMES DE SECURITE LASER

Ce produit est conforme aux normes de sécurité laser en vigueur à sa date de fabrication: CDRH 21 CFR 1040 et EN 60825-1.

Il n’est pas nécessaire d’ouvrir l’appareil pour l’installation, l’utilisation ou l’entretien.

LNe pas essayer d’ouvrir ou de réparer les composants de la cavité optique. L’ouverture de la cavité optique ou la réparation de ses composants par une personne non qualifiée peut entraîner le nonrespect des règles de sécurité relatives au laser. Le système optique ne peut être réparé qu’en usine.

L'utilisation de procédures ou réglages différents de ceux donnés ici peut entraîner une dangereuse exposition à lumière laser visible.

L’utilisation d’instruments optiques avec le scanneur augmente le danger pour les yeux. Les instruments optiques comprennent les jumelles, les microscopes, les lunettes et les verres grossissants.

ATTENTION

Le produit utilise une diode laser. Aucun dommage aux yeux humains n’a été constaté à la suite d’une exposition au rayon laser. Eviter de regarder fixement le rayon, comme toute autre source lumineuse intense telle que le soleil. Eviter aussi de diriger le rayon vers les yeux d’un observateur, même à travers des surfaces réfléchissantes (miroirs, par exemple).

ESPAÑOL

Las informaciones siguientes son presentadas en conformidad con las disposiciones de las autoridades internacionales y se refieren al uso correcto del terminal.

NORMATIVAS ESTÁNDAR PARA LA SEGURIDAD LÁSER

Este aparato resulta conforme a las normativas vigentes de seguridad láser a la fecha de producción: CDRH 21 CFR 1040 y EN 60825-1.

No es necesario abrir el aparato para la instalación, la utilización o la manutención.

ATENCIÓN

No intente abrir o de ninguna manera dar servicio a ninguno de los componentes del receptáculo óptico. Abrir o dar servicio a las piezas del receptáculo óptico por parte del personal no autorizado podría ser una violación a los reglamentos de seguridad. El sistema óptico se puede reparar en la fábrica solamente.

La utilización de procedimientos o regulaciones diferentes de aquellas describidas en la documentación puede causar una exposición peligrosa a la luz láser visible.

El uso de sistemas ópticos con el escáner aumentará el riesgo de daños oculares. Los instrumentos ópticos incluyen binoculares, microscopios, lentes y lupas.

El aparato utiliza un diodo láser a baja potencia. No son notorios daños a los ojos humanos a consecuencia de una exposición de corta duración.

Eviten de mirar fijo el rayo láser así como evitarían cualquiera otra fuente de luminosidad intensa, por ejemplo el sol. Además, eviten de dirigir el rayo láser hacia los ojos de un observador, también a través de superficies reflectantes como los espejos.

LED Class

LED illuminators integrated in the LYNX models with SE-4500 imager engine are compliant with exempt risk group requirements according to

IEC62471:2006 and EN62471:2008.

Flash LED integrated in the LYNX models with camera is blue light hazard risk group 1 according to IEC62471:2006 and EN62471:2008.

Marking and European Economic Area (EEA)

In radio systems configured with mobile computers and access points, the frequencies to be used must be allowed by the spectrum authorities of the specific country in which the installation takes place. Be absolutely sure that the system frequencies are correctly set to be compliant with the spectrum requirements of the country.

The Radio modules used in this product automatically adapt to the frequencies set by the system and do not require any parameter settings.

The TYPE field shows the correspondence between LYNX™ types and radio modules:

TYPE: ABCDEE-FGH-IJJK-LMMMM

A: “0” if WWAN module is not present, “E” for GSM/GPRS/EDGE WWAN module, “U” for UMTS/HSDPA WWAN module, “H” for UMTS HSPA+

Voice and Data

B: “0” if GPS module is not present

C: “0” if IEEE 802.11 module is not present, “A” for IEEE 802.11 abg module, “G” for IEEE 802.11 bg module, “N” for IEEE 802.11 bgn module

D: “0” if RFID module is not present.

Statement of compliance

The manufacturer Declaration of Conformity may be found on the product user manual at www.datalogic.com website.

BG

С настоящото Datalogic S.r.l. декларира, че този тип радиосъоръжение LYNX е в съответствие с Директива 2014/53/ЕС.

Цялостният текст на ЕС декларацията за съответствие може да се намери на следния интернет адрес:

www.datalogic.com

.

ES

Por la presente, Datalogic S.r.l. declara que el tipo de equipo radioeléctrico LYNX es conforme con la Directiva 2014/53/UE. El texto completo de la declaración UE de conformidad está disponible en la dirección Internet siguiente: www.datalogic.com

.

CS

Tímto Datalogic S.r.l. prohlašuje, že typ rádiového zařízení LYNX je v souladu se směrnicí 2014/53/EU. Úplné znění EU prohlášení o shodě je k dispozici na této internetové adrese: www.datalogic.com

.

DE

Hermed erklærer Datalogic S.r.l., at radioudstyrstypen LYNX er i overensstemmelse med direktiv 2014/53/EU. EUoverensstemmelseserklæringens fulde tekst kan findes på følgende internetadresse: www.datalogic.com

.

ET

Käesolevaga deklareerib Datalogic S.r.l., et käesolev raadioseadme tüüp LYNX vastab direktiivi 2014/53/EL nõuetele. ELi vastavusdeklaratsiooni täielik tekst on kättesaadav järgmisel internetiaadressil: www.datalogic.com

ΕL

Με την παρούσα ο/η Datalogic S.r.l., δηλώνει ότι ο ραδιοεξοπλισμός LYNX πληροί την οδηγία 2014/53/ΕΕ. Το πλήρες κείμενο της

δήλωσης συμμόρφωσης ΕΕ διατίθεται στην ακόλουθη ιστοσελίδα στο διαδίκτυο:

www.datalogic.com

.

EN

Hereby, Datalogic S.r.l. declares that the radio equipment type LYNX is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: www.datalogic.com

.

FR

Le soussigné, Datalogic S.r.l., déclare que l'équipement radioélectrique du type LYNX est conforme à la directive 2014/53/UE. Le texte complet de la déclaration UE de conformité est disponible à l'adresse internet suivante: www.datalogic.com

.

HR

Datalogic S.r.l. ovime izjavljuje da je radijska oprema tipa LYNX u skladu s Direktivom 2014/53/EU. Cjeloviti tekst EU izjave o sukladnosti dostupan je na sljedećoj internetskoj adresi: www.datalogic.com

.

IT

Il fabbricante, Datalogic S.r.l., dichiara che il tipo di apparecchiatura radio LYNX è conforme alla direttiva 2014/53/UE. Il testo completo della dichiarazione di conformità UE è disponibile al seguente indirizzo Internet: www.datalogic.com

.

LV

Ar šo Datalogic S.r.l. deklarē, ka radioiekārta LYNX atbilst Direktīvai 2014/53/ES. Pilns ES atbilstības deklarācijas teksts ir pieejams šādā interneta vietnē: www.datalogic.com

.

LT

Aš, Datalogic S.r.l., patvirtinu, kad radijo įrenginių tipas LYNX atitinka Direktyvą 2014/53/ES. Visas ES atitikties deklaracijos tekstas prieinamas

šiuo interneto adresu: www.datalogic.com

.

HU

Datalogic S.r.l. igazolja, hogy a LYNX típusú rádióberendezés megfelel a 2014/53/EU irányelvnek. Az EU-megfelelőségi nyilatkozat teljes szövege elérhető a következő internetes címen: www.datalogic.com

.

MT

B'dan, Datalogic S.r.l. niddikjara li dan it-tip ta' tagħmir tar-radju LYNX huwa konformi mad-Direttiva 2014/53/UE. It-test kollu tad-dikjarazzjoni ta' konformità tal-UE huwa disponibbli f'dan l-indirizz tal-Internet li ġej: www.datalogic.com

.

PL

Datalogic S.r.l. niniejszym oświadcza, że typ urządzenia radiowego LYNX jest zgodny z dyrektywą 2014/53/UE. Pełny tekst deklaracji zgodności

UE jest dostępny pod następującym adresem internetowym: www.datalogic.com

.

PT

O(a) abaixo assinado(a) Datalogic S.r.l. declara que o presente tipo de equipamento de rádio LYNX está em conformidade com a Diretiva 2014/

53/UE. O texto integral da declaração de conformidade está disponível no seguinte endereço de Internet: www.datalogic.com

.

RO

Prin prezenta, Datalogic S.r.l. declară că tipul de echipamente radio LYNX este în conformitate cu Directiva 2014/53/UE. Textul integral al declarației UE de conformitate este disponibil la următoarea adresă internet:

www.datalogic.com

.

SK

Datalogic S.r.l. týmto vyhlasuje, že rádiové zariadenie typu LYNX je v súlade so smernicou 2014/53/EÚ. Úplné EÚ vyhlásenie o zhode je k dispozícii na tejto internetovej adrese: www.datalogic.com

.

SL

Datalogic S.r.l. potrjuje, da je tip radijske opreme LYNX skladen z Direktivo 2014/53/EU. Celotno besedilo izjave EU o skladnosti je na voljo na naslednjem spletnem naslovu: www.datalogic.com

FI

Datalogic S.r.l. vakuuttaa, että radiolaitetyyppi LYNX on direktiivin 2014/53/EU mukainen. EU-vaatimustenmukaisuusvakuutuksen täysimittainen teksti on saatavilla seuraavassa internetosoitteessa: www.datalogic.com

.

SV

Härmed försäkrar Datalogic S.r.l. att denna typ av radioutrustning LYNX överensstämmer med direktiv 2014/53/EU.Den fullständiga texten till

EU-försäkran om överensstämmelse finns på följande webbadress: www.datalogic.com

.

Frequency Ranges

Bluetooth and Wi-Fi radio:

2400-2483.5 MHz eirp < 20 dBm,

GPS:

1575 MHz – 1585 MHz

WWAN:

GSM900: 880 MHz – 915 MHz (Tx) / 925 – 960 MHz (Rx)

GSM1800: 1710 MHz – 1785 MHz (Tx) / 1805 MHz – 1875 MHz (Rx)

WCDMA900: 880 MHz – 915 MHz (Tx) / 925 MHz – 960 MHz (Rx)

WCDMA2100: 1920 MHz – 1980 MHz (Tx) / 2110 MHz – 2710 MHz (Rx)

GSM900: Power Class 4 (33dBm)

GSM1800: Power Class 1 (30dBm)

WCDMA900: Power Class 3 (24dBm)

WCDMA2100: Power Class 3 (24dBm)

Information for the User

ENGLISH

Contact the competent authority responsible for the management of radio frequency devices of your country to verify any possible restrictions or licenses required.

ITALIANO

Prendi contatto con l'autorità competente per la gestione degli apparati a radio frequenza del tuo paese, per verificare eventuali restrizioni o licenze.

DEUTSCH

Wenden Sie sich an die für Radiofrequenzgeräte zuständige Behörde Ihres Landes, um zu prüfen ob es Einschränkungen gibt, oder eine Lizenz erforderlich ist.

FRANÇAIS

Contactez l'autorité compétente en la gestion des appareils à radio fréquence de votre pays pour vérifier d'éventuelles restrictions ou licences.

ESPAÑOL

Contacta la autoridad competente para la gestión de los dispositivos de radio frecuencia de tu país, para verificar cualesquiera restricciones o licencias posibles requerida.

Bluetooth® Approval

For more information visit: http://www.bluetooth.org/tpg/listings.cfm

.

FCC Compliance

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiated radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

•

•

•

•

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the party responsible for compliance could void the user‘s authority to operate the equipment.

The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

RF Exposure Information (SAR)

This model device meets the government’s requirements for exposure to radio waves. This device is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the U.S. Government.

The exposure standard for wireless devices employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6W/kg. Tests for SAR are conducted using standard operating positions accepted by the FCC with the device transmitting at its highest certified power level in all tested frequency bands. Although the SAR is determined at the highest certified power level, the actual SAR level of the device while operating can be well below the maximum value. This is because the device is designed to operate at multiple power levels so as to use only the poser required to reach the network. In general, the closer you are to a wireless base station antenna, the lower the power output.

While there may be differences between the SAR levels of various devices and at various positions, they all meet the government requirement.

The FCC has granted an Equipment Authorization for this model device with all reported SAR levels evaluated as in compliance with the FCC RF exposure guidelines. SAR information on this model device is on file with the FCC and can be found under the Display Grant section of http:// www.fcc.gov/oet/fccid after searching on the below FCC ID: FCC ID: U4G0070 and U4G0073

This device is compliant with SAR for general population /uncontrolled exposure limits in ANSI/IEEE C95.1-1999 and had been tested in accordance with the measurement methods and procedures specified in OET Bulletin 65 Supplement C.

For body worn operation, this device has been tested and meets the FCC RF exposure guidelines for use with an accessory that contains no metal and the positions the handset a minimum of 1.5 cm from the body. Use of other enhancements may not ensure compliance with FCC RF exposure guidelines. If you do not use a body-worn accessory and are not holding the device at the ear, position the handset a minimum of 1.5

cm from your body when the device is switched on.

Industry Canada Compliance

Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du

Canada.

This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter.

The County Code Selection feature is disabled for products marketed in the US/Canada.

IMPORTANT NOTE:

IC Radiation Exposure Statement

This EUT is compliant with SAR for general population/uncontrolled exposure limits in IC RSS-102 and had been tested in accordance with the measurement methods and procedures specified in IEEE 1528. This equipment should be installed and operated with minimum distance 1,5cm between the radiator & your body.

SAR Compliance

1.

2.

3.

4.

5.

For the used worst case positions, the portable device Lynx from Datalogic (FCC ID: U4G0070 and U4G0073) is in compliance with the IC

RSS 102 Issue 4 [RSS 102] and Federal Communications Commission (FCC) Guidelines [OET 65] for uncontrolled exposure. SAR assessment in body worn was conducted with a distance of 15 mm between the housing of the handheld and the flat phantom.

CE SAR assessment in body worn was conducted with a distance of 5mm between the housing of the handheld and the flat phantom.

EN 50360:2001+A1:2012: product standard to demonstrate the compliance of mobile phones with the basic restrictions related to human exposure to electromagnetic fields (300 MHz – 3 GHz).

EN 50566:2013 Product standard to demonstrate compliance of radio frequency fields from handheld and body-mounted wireless communication devices used by the general public (30 MHz — 6 GHz).

EN 62209-1:2006: Human exposure to radio frequency fields from hand-held and body-mounted wireless communication devices.

Human models, instrumentation, and procedures. Procedure to determine the specific absorption rate (SAR) for hand-held devices used in close proximity to the ear (frequency range of 300 MHz to 3 GHz).

EN 62209-2:2010: Human exposure to radio frequency fields from hand-held and body-mounted wireless communication devices.

Human models, instrumentation, and procedures. Procedure to determine the specific absorption rate (SAR) for wireless communication devices used in close proximity to the human body (frequency range of 30 MHz to 6 GHz).

Canadian Statement

Ne pas regarder le faisceu.

Attention classe 2 lumière laser en cas d’ouverture eviter l’esposition - lumière est émise de la ouverture.

Ce produit est conform au sous-chapitre J de CFR 21.

Rayonnement laser – ne pas regarder dans le faisceu – ne par regarder avec strumentation optique - appareil à laser de classe 2 – emission maximale de 1mw – longueur d’onde emise

630 - 680nm – selon EN 60825-1:2007