718530514
Owner’s Manual
& Assembly Guide
www.arrowsheds.com
01O
Customer Service:
UNIT DIMENSIONS
10 Sq. Ft.
0,9 m 2
Storage
Area
21 Cu. Ft.
0,6 m 3
PATENT PENDING
Width
Exterior Dimensions
(Lid Edge to Lid Edge)
Depth Height
57 3/8”
145,7 cm
29 3/4”
75,6 cm
28”
71,1 cm
* See Inside for Detailed Safety Information.
Gloves must be worn at all times to reduce risk of injury!
Width
53 3/4”
Interior Dimensions
(Wall to Wall)
Depth Height
26 1/16” 26”
136,5 cm 66,2 cm 66 cm
BEFORE YOU BEGIN...
Safety precautions MUST be followed at all times throughout the construction of your Storage Unit!
•Care must be taken when handling various pieces of your Storage Unit since many contain sharp edges. Please wear work gloves, eye protection and long sleeves when assembling or performing any maintenance on your Storage
Unit.
02L
•Practice caution with the tools being used in the assembly of your Storage
Unit. Be especially familiar with the operation of all power tools.
•Keep children and pets away from the worksite during construction. Do not allow children to help with assembly.
•Do NOT attempt to assemble your Storage Unit on a windy day. The large panels can catch the wind like a “sail”, causing them to be whipped around making construction diffi cult and unsafe.
•We recommend two people work together to assemble your Storage Unit.
This will make assembly faster and easier.
Reading and following all steps carefully will help make assembly quicker and easier. Before you begin assembly, be sure to confi rm that all the parts for your Storage Unit are present using the checklist on pages 3 and 4.
If parts are missing, include the model number of your storage unit and contact Customer
Service at 1-800-851-1085 or online at [email protected].
NOT RECOMMENDED FOR STORAGE OF CORROSIVE CHEMICALS OR PRODUCTS
Below is a list of things you will need to assemble your Storage Unit.
WHAT YOU NEED
• Work Gloves
• Safety Glasses
• No. 2 Phillips Screwdriver (Magnetic Tip Preferred)
• Pliers
RECOMMENDED TIME SAVERS
• Power Drill (Cordless, Variable Speed)
• Nut Driver or Wrench
• Awl (to help align holes)
2
HARDWARE LIST...
1
Key Part Part
No. No. Description
Qty.
List
12 69959
13 69953
14 66798
15 66784
16 69965
17 69966
18 69967
19 66792
20 69968
21 66801
22 60H
7
8
5
6
3
4
1
2
9 69961
10 66676
11 66803
69971
69960
Hex Nut (#8-32)
Small Bolt (#8-32 x 3/8) (10 mm)
69972 Small Screw (#8AB x 5/16) (8 mm)
69972-60 Small Screw (Painted) (#8AB x 5/16) (8 mm)
69973
69974
69958
69962
Large Screw (#10AB X 1/2) (13 mm)
Flat Head Bolt (#8-32 X 1/2) (13 mm)
Long Screw (#6AB X 7/8) (22 mm)
Small Flat Head Bolt (#6-32 X 7/16) (11 mm)
Hex Nut (#6-32)
Push Pin
Flat Head Self Tapping Screw (#8A X 1/2) (13 mm)
#8 Lock Washer
Plastic Foot
Foam Tape
Offset Hinge
Lid Stay
End Cap Strap
Lid Catch
Locking T-Handle
Latch
Plastic Spacer
Corner Cap
3
6
1
1
3
2
9
1
2
1
1
8
1
27
6
30
22
58
6
1
46
3
2
#2 Phillips
10
13
16
19
SB 3
#2 Phillips
LNS 8
#2 Phillips
SFB
PP
#2 Phillips
11 FSS
#2 Phillips
14
17
20
03O
SS
4
11/32 Hex.
PSS 5
#2 Phillips
LS 6
#2 Phillips
FB
7
#2 Phillips
9
5/16 Hex.
12
15
#8 Lock
Washer
18
Part Numbers
21 22
Part Number
1. Each part has an identifying part number on it.
2. Part Numbers are referenced in each step.
3. Unpainted parts have a stamped in number and painted
parts have a number that is inked on.
Remove inked on numbers with soap and water after assembly.
3
Confi rm that all hardware and parts are present before attempting to assemble your Storage Unit.
For missing or damaged parts contact
Customer Service. Do not return to store.
Customer Service:
PARTS LIST...
Key Part Part
No. No. Description
1 10682 Floor Section
2 10683 Front & Rear Floor Section
Qty.
List
4
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
10685
10686
10687
10688
10689
10690
10691
10692
10693
10694
10695
6481
10697
10698
10696
Front & Rear Floor Channel
Side Floor Channel
Lid Handle Panel
Wall Panel
Corner Panel
U-Splice
Lid Stay Brace
Lid Handle Brace
Front Top Channel
Rear Top Channel
Side Top Channel
Gusset
Lid Support
Lid Panel
Lid End Cap
1
2
2
5
1
2
1
1
12
3
7
4
2
1
2
2
Selected End Views by Key No.
1
4
Unpainted
Painted/
Unpainted
10
Unpainted
13
2
8
Unpainted
Unpainted
11
Painted/
Unpainted
14
3
9
Painted/
Unpainted
Unpainted
12
Painted/
Unpainted
15
Painted/
Unpainted
Unpainted
17
Unpainted
At the top of each page you will see one or more Part Cues like the one to the right. These Part Cues are designed to help you quickly identify the parts needed for each step.
Quantity Needed
Part No.
10697
End View
Part Name
Lid Support
5
Various fasteners are used throughout the construction of your storage unit. In each step you will see the abbreviations listed below used in the illustrations to help you identify which fastener to use.
SB - Small Bolt
SS - Small Screw
LS - Large Screw
PP - Push Pin
FB - Flat Head Bolt SB
PSS - Painted Small Screw
LNS - Long Screw
SFB Small Flat Head Bolt
SB
FSS - Flat Head Self Tapping Screw
Painted/
Unpainted
The fasteners used in each step are shown actual size at the top of each page. If you are unsure which fastener to use, hold it up to the picture and use the one that matches.
QTY 18
04L
ASSEMBLY BY KEY NO.
NOTE: The U-Splice,
Key No. 8 (Part No.
10690) is used at each
Panel connection.
16
17
15
15
15
15
15
14
13
12
14
6
7
9
11
6
6
9
6
13
9
7
6
5
10
6
7
6
7
8
17
05L
4
3
3
2
1
1
1
1
2
5
4
Step 1
You will need for this page:
SB SFB
(QTY: 2)
LNS
(QTY: 1)
69953
6
10682
3
Plastic Foot Floor Section
10683
1
F/R Floor
Section
10685
1
F/R Floor
Channel
10686
2
Side Floor
Channel
06L
(QTY: 5)
1
Attach one (1) Front/Rear Floor
Section to a Front/Rear Floor
Channel at the middle by using a Plastic Foot and securing with one (1) Long Screw as shown.
10686
2
Attach Side Channels and
Plastic Feet with one (1) Long
Screw at each corner.
LNS
The Front and Rear Floor Section should be aligned with the Front and Rear Floor
Channels as shown.
Plastic Foot
LNS
10683
10685
Plastic Foot
LNS
Note hole locations
SB
10682 Plastic
Foot
LNS
10682
10682
10682
SFB
SB
SB
10686
Floor Channels overlap as shown.
Plastic Foot LNS 10685 10686
Do not tighten Small Bolts or Small Flat Head Bolt until after Floor is square.
3
Plastic Foot
Slide three (3) Floor Sections into the Side Channels one at a time. Secure in the middle using two (2) Small Bolts and a Small Flat Head Bolt with a
Plastic Foot as shown.
Once all have been attached, secure ends of last
Floor Section inserted to the Side Channels using one (1) Long Screw and Plastic Foot .
Step 2
You will need for this page:
LNS SB
(QTY: 3) (QTY: 2)
66798
1
Foam Tape
10682
1
Floor Section
1 Slide Floor Section and Front/
Rear Floor Section into place.
Secure using two (2) Small Bolts at the middle.
2 Attach Front/Rear Floor Channel and three (3) Plastic Feet using three (3) Long Screws as shown.
LNS
Plastic Foot
10683
10682
LNS
10685
Note hole locations
3 Once Floor is complete, turn completed fl oor over. At this time, take a moment to ensure the unit is level and square. Measure diagonally, when the diagonal measurements are equal, the Floor is square.
IMPORTANT: IF STORAGE UNIT
IS NOT SQUARE, LID WILL NOT
CLOSE PROPERLY!
10683
1
F/R Floor
Section
69953
Plastic Foot
3
10685
1
F/R Floor
Channel
SB
SB
Plastic Foot
LNS
Plastic Foot
Level
07L
4 Seal corners of Floor with Foam Tape . Cut four (4)
1” (2,5 cm) strips to place between Floor Channels at the corners.
After Floor is square tighten bolts holding Floor Sections together.
7
Step 3
You will need for this page:
PP
(QTY: 6)
10687
1
Lid Handle
Panel
10688
2
Wall Panel
10690
2
U-Splice
1 Pre-assemble Front Panels together using two (2) U-Splices and six (6) Push Pins leaving the top paired hole vacant. These holes will be used to attach the Lid Handle Brace in a later step.
08L
Paired holes and hinge holes at top.
10688
10687
10688
Single hole at bottom.
10688
10690
Slide U-Splice over the Panels where the Panels meet and secure using
Push Pins .
PP
10690
To help with aligning holes, use an awl. This will make inserting Push Pins easier.
If Push Pins will not go in all the way, lightly tap Push Pin with a hammer.
10687
8
PP Except on Lid
Handle Panel to allow room to install
Lid Handle Brace .
PP
PP
PP
Step 4
You will need for this page:
PP
10688
3
10690
2
(QTY: 8) Wall Panel U-Splice
1
Pre-assemble Back Panels together using two (2) U-Splices and eight (8) Push Pins.
Paired holes and hinge holes at top.
10688
10688
10688
09L
Single hole at bottom.
10688
10690
Slide U-Splice over the Panels where the Panels meet and secure using
Push Pins .
PP
10690
To help with aligning holes, use an awl. This will make inserting Push Pins easier.
If Push Pins will not go in all the way, lightly tap Push Pin with a hammer.
10688
9
PP
PP
PP
PP
Step 5
You will need for this page:
PP
10688
2
10689
4
10690
4
(QTY: 16) Wall Panel Corner Panel U-Splice
1
Pre-assemble Side Panels together using two (2) U-Splices and eight (8) Push Pins. Make two (2) assemblies.
10L
Hinge holes at top.
10689
10688
10689
Single hole at bottom.
10688
10690
Slide U-Splice over the Panels where the Panels meet and secure using
Push Pins .
10690
PP
10689
10
To help with aligning holes, use an awl. This will make inserting Push Pins easier.
If Push Pins will not go in all the way, lightly tap Push Pin with a hammer.
PP
PP
PP
PP
Step 6
You will need for this page:
SB LS PP
10690
4 Assemblies from steps 3,4,&5:
• Front Panel Assembly (1)
B
U-Splice (QTY: 6) (QTY: 6) (QTY: 16)
1 Position each Panel Assembly as shown and secure to the Floor with one (1) Large Screw in the bottom leg of each Front and Rear Panel and Small Bolt in each Side Panel .
11L
Hinge holes at top.
C
B
A C
SB
LS
2
Single hole at bottom.
SB
Secure Panel Assemblies together using four (4) U-Splice and sixteen (16) Push Pins .
PP
10690
Slide U-Splice over the Panels where the Panels meet and secure using
Push Pins .
10690
PP
PP
To help with aligning holes, use an awl. This will make inserting Push Pins easier.
If Push Pins will not go in all the way, lightly tap Push Pin with a hammer.
PP
PP
10688 10687
11
Step 7
You will need for this page:
SB
69965
3
10691
3
(QTY: 6) Lid Stay Lid Stay Brace
1
Pre-assemble the Lid Stay to the Lid Stay Brace using two (2) Small Bolts and Nuts . Make three (3) assemblies.
SB
12O
69965
10691
2 Place the two (2) outside Lid Stay/Brace Assemblies into Back Corner Panel.
DO NOT install, just set in place as shown and set third assembly aside for now.
Rear Corner Panel
12
Step 8
You will need for this page:
SB SS
10693
1
Front Top
Channel (QTY: 4) (QTY:14)
10694
1
Rear Top
Channel
10695
2
Side Channel
6481
2
Gusset
60H
Corner Cap
2
1
First install top channels starting with Front and Rear Channels, then install Side Channels using ten (10) Small Screws.
When installing Top Channels, start on inside lip of
Wall Panels then rotate to the outside.
SS
SS
SS
10695
10694 SS
SS
SS
SS
SS
SS
10695
SS
10693
13L
2 Install Corner Caps on front corners using two (2) Small Bolts . Install Gussets on back corners using four (4) Small Screws and two (2) Small Bolts .
SB
SS
SS
6481
SB SS SB
SS
60H
SB
13
Step 9
You will need for this page:
SS
10692
1
Lid Handle
Brace
(QTY: 2)
66792
1
Locking
T-Handle
SS
1
Install Lid Handle Brace to Lid Handle Panel as shown using two (2) Small Screws .
10687
SS
10692
Slide Lid Handle Brace over
U-Splice and secure using
Small Screws .
14L
Bend end fl aps down as shown before installation.
10692
10692
2 Install Locking T-Handle using two (2) Long Bolts which are packed with Locking T-Handle .
66792
Packed with Locking
“T”Handle
614
Step 10
You will need for this page:
SS
• Lid Stay/Brace Assemblies (3)
(QTY: 12)
1 Install three (3) Lid Stay/Brace Assemblies into the back panels by angling them into place; one in each
Back Corner Panel and one in Middle Panel .
2 Secure each Lid Stay / Brace Assembly using four (4)
Small Screws . Two on top and two on botton of brace.
Apply pressure to Top Channel to help align top holes.
SS
2 nd
15L
First attach bottom of Lid Stay/
Brace Assembly, then attach top of the Lid Stay/Brace Assembly.
1 st
615
SS
Step 11
You will need for this page:
SB 69959
(QTY: 2) (QTY: 2)
10697
1 69967
1
Lid Support Lid Catch
1
For the middle Lid Support attach the Lid Catch using two (2) Small Bolts, Lock Washer, and four (4) Nuts .
16O
69967
#8 Lock Washer
10697
SB SB
Loosen top nut to adjust fi t between Latch and Lid Catch .
16
Step 12
You will need for this page:
LS SS PSS
10697
5
10696
2
69966
6
10698
Lid Panel
1
(QTY: 12) (QTY: 24) (QTY: 6) Lid Support Lid End Cap
End Cap
Strap
1 Start lid assembly by sliding Lid Support with Lid Catch into position as shown. Then slide remaining four (4) Lid Supports into position, making sure all Lid Supports are facing the same way. Secure all Lid Supports to Lid Panel using (20) Small Screws , two at each end.
SS
17O
Lid
Catch
Hinge holes at the bottom.
2
SS
Attach the Lid End Caps and End Cap Straps to the Lid Panel using twelve (12) Large
Screws , four (4) Small Screws, and six (6) Painted Small Screws .
SS
LS
PSS
SS
LS
17
Step 13
You will need for this page:
LS SS FB FSS
66784
3
(QTY: 9) (QTY: 6) (QTY: 6) (QTY: 3) Offset Hinge
1
Install three (3) Hinges using six (6) Flat Head Bolts and three (3) Flat Head Self Tapping
Screws .
FB
FSS
FB
FB
18L
Inside Outside
2
Secure lid to base by attaching all three (3)
Hinges to lid using nine (9) Large Screws .
3 Attach the three (3) Lid Stays to the
Lid using six (6) Small Screws .
SS
LS
18
Step 14
You will need for this page:
69968
1
Latch
66801
Plastic Spacer
1
1 Install Latch and Plastic Spacer to the inside of the
Locking T-Handle.
Secure with Push Nut found in the Locking T-handle packaging.
Pay careful attention to position of Latch.
2 Adjust Lid Catch as needed to ensure Latch completely locks into place as shown below.
Lid Catch
Latch
Loosen top nut to adjust fi t between Latch and Lid Catch .
19O
Push Nut
69968
66801
19
CARE & MAINTENANCE...
Exterior Care:
For a long lasting fi nish clean and wax the exterior surface. We recommend washing with a mild soap solution. DO NOT use power washing, bleach, ammonia, or caustic cleaner to clean your storage unit.
Using a spray automotive type wax periodically on the exterior is highly recommended if you are in a high humidity or coastal climate region.
20L
Combustibles must be stored in air tight containers designed for combustible storage.
NOT RECOMMENDED FOR STORAGE OF CORROSIVE OR FLAMMABLE
CHEMICALS OR PRODUCTS
Rust protection precautions may help to stop rust from developing, or stop it quickly as soon as it appears.
• Do not stand on lid.
• Avoid nicking or scraping the coating surface, inside and out.
• Keep storage unit free of debris and leaves which may accumulate and retain moisture. These can do double damage since they give off acid as they decay.
• Touch up scrapes or nicks and any area of visible rust as soon as possible. Make sure the surface is free of moisture, oils, dirt or grime and then apply an even fi lm of high quality touch-up paint.
• Various paint manufacturers provide products for rust treatment and coverage. If surface rust does appear on your storage unit we recommend treating those areas as soon as possible, following the paint supplier of your choice instructions.
• Our customer service department can provide the paint tinting formula for matching the color of your storage unit. We also have touch-up paint available for repairing small nicks and scratches.
• Exercise caution when moving fully loaded product. This is not intended for transporting heavy objects.
This product is recommended for stationary storage.
• Not intended for usage by children. This is not a toy box. To avoid risk of suffocation, do not allow children to play inside container.
Fasteners:
Use all washers supplied to protect against weather infi ltration and to protect the metal from being scratched by the screws. Regularly check screws, bolts, nuts, etc., and retighten as necessary.
General:
• Wash off inked part numbers on coated panels with soap and water.
• Silicone caulking may be used for watertight seals throughout the storage unit.
Please note, Manufacturer cannot be held responsible for any consequences due to storage units that are not installed per these instructions, or for damage due to weather conditions or acts of God.
Keep these assembly instructions and owner’s manual for future reference.
20
