Nuga NM-5000 User Manual
Nuga NM-5000 features a streamline design for comfortable use, beautiful materials with a premium feel, and a blue color to promote concentration and psychological stability. Its functional product frame includes a horizontally built main and sub mat for convenient use with a handle that can be controlled in three steps. The internal projector is designed in human engineering with separately built ceramics around the cervical vertebrae for equal acupressure load distribution and can be rotated up/down/left/right.
Advertisement
Advertisement
[ ENGLISH ] www.nuga.kr
185, Jiraeul-ro, Jijeong-myeon, Wonju-si,
Gangwon-do, Korea
TEL : +82-33-730-0001 / FAX : +82-33-730-0007 http://www.nuga.kr
ENGLISH / CE H/H / Rev. 08
2015.11.10
NM-5000
User Manual
Thank you for purchasing this product.
Before use...
Please read the cautions for safety in the user manual to use this product safely.
Quality Warranty Enclosed
Tourmanium Product
Contents
Product Introduction
Product features
Guide and Sequence for Product Installation
Product Components
Product Frame Components
Tray with Screws for Assembly
Names and Functions of Product Components
Descriptions for Remote Controller Buttons
Product Installation and Preparations
Before the Product Installation
How to Assemble the Product Frame
How to Install the Product
Test Operations after Installation
How to Use the Product
How to Use the Remote Controller
How to Use the Product by Mode
How to Use the External Projector
How to Use the Low Frequency Pad
How to Use the Product
How to Set Temperature for the Sub Heater
Product Storage and Care
How to Store and Clean the Product after Use
Check Indicator Window of Remote Controller
How to Take Emergency Actions during Use
Self-check Items
Before any A/S Request
Product Specifications
Memo
Product Warranty
NM-5000
44
45
46
47
40
41
42
43
28
28
33
34
36
38
12
14
16
8
9
10
11
18
20
24
26
Cautions for Safety
Cautions for your safety
· These cautions include descriptions for the safety of users and prevention
of any damage to properties among others.
· Read through the following details to use the product appropriately.
· This Manual classified the risk level into the following three degrees and the
following graphical symbols aim to remind users of cautions for matters and
operations of concerns about any risk.
Interpretations on symbols
Danger
If there is high possibility of death due to non-compliance.
Warning
If there is a possibility of an injury or death due to non-compliance.
Caution
If there is a possibility of a minor injury or damage to goods due to non-compliance.
Disclaimer
· The manufacturer, importer and/or agent shall not be responsible for any
problem and/or other damage to the product which has been caused from the
user’s careless care or operation.
· Information in the user manual has been prepared on the basis of the current
product specifications.
· Details on the user manual might be different from those on the product.
· The product manufacturer is adding and supplementing new functions at any
time and new technologies shall be applied to the product continuously in the
future as well.
· All the standards and functions are subject to change without any notice to
users to improve performance.
Cautions for Safety
Danger Warning
Put the projector cover on the projector while using the projector to keep the projector from touching the skin directly.
(Otherwise, it is likely that injuries occur.)
Ensure applying the product only abdominal area manually, while keeping the product from applying to the area around ribs if you have to apply the product to the abdominal area.
Avoid applying the projector directly to eyeballs to prevent from any risk.
(Otherwise, it might cause damage to eyeballs.)
Avoid placing inflammable substances like candlelight, cigarette light or liquors and/or vessels containing water, heavy objects or other objects on the product.
(Otherwise, it might cause fire.)
Do not insert many power plugs for other products into a socket to be used simultaneously.
(Otherwise, it might cause electric shock, injury and/or damage to the product.)
Avoid twisting the body while the internal projector is being operated.
(Otherwise, it might cause excessive influences to the spine.)
Avoid pulling out the power cord parts or touching the power plug with the wet hand.
(Otherwise, it might cause the electrical shock or fire.)
Immediately stop using the product and turn off the power if there is any thunder, lightning or earthquake.
(Otherwise, it might cause the electrical shock or fire.)
Prohibit any pregnant woman near the parturition, patients with rachischisis, patients wearing a cardiac pacemaker and/or patients with severe heart diseases from using the product.
Avoid using any band or belt that does not come as one of components from the purchase of the product.
(Otherwise, it might cause damage to the product.)
Apply the product to the area with any surgery and/or treatment, after consulting with the store or the company from which you have purchased the product.
Do not allow any child to use the product alone.
Avoid using the product in a closed place with any fuel and/or chemical.
(Otherwise, it might cause injuries or fire.)
Avoid using the product in a place with a great deal of dusts or intensive temperature change.
(Otherwise, it might cause the electrical shock or fire.)
Anyone other than technicians qualified for our company’s A/S shall not disassemble, repair or modify the product by any means.
(Otherwise, it might cause damage to the product or electric shock and/or fire.)
NM-5000
Avoid jumping on the product or any other action to provide shocks to the product.
(Otherwise, it might cause injuries and/or damage to the product.)
Use the product after checking out any damaged or worn-out cord.
(Otherwise, it might cause electric shock, injury and/or damage to the product.)
Avoid bending the power cord excessively or pressing it down with heavy objects.
Cautions for Safety
Caution
Install the product horizontally.
Please abide by using time and methods.
Separate the power cord while the product is not being in use for a long time.
]WGGGGGGGGGGGGGGGG]W
\WGGGGGGGGGGGGGGGG\W
[WGGGGGGGGGGGGGGGG[W
ZWGGGGGGGGGGGGGGGGZW
Use the product in a range of proper temperature as there are concerns of burns if the higher temperature is set.
Connect the power supply after connecting the remote controller first.
Be aware of dangers that you might fall down when you get on or off the product.
Any pregnant shall not use the low frequency pad.
Move the product after separating the power supply from connecting lines if the product is moved.
Check out the applied voltage before any use and apply the power plug only to a dedicated socket.
NM-5000
NM-5000
Product Introduction
Product features
Guide and Sequence for Product Installation
Product Components
Product Frame Components
Tray with Screws for Assembly
Names and Functions of Product Components
Descriptions for Remote Controller Buttons
11
12
14
16
8
9
10
Product features
Fine Design
ⴘ The design in a streamline shape makes you feel comfortable during use.
ⴙ Beautiful materials with good feelings of touch in high quality are applied.
ⴚ The product in blue helps you improve concentration and psychological
stability.
Functional Product Frame
Both the main mat and sub mat are horizontally built, which can be used more conveniently with the attachment of a handle to be controlled in 3 steps
UHVSHFWLYHO\IRUWKHGHVLUHGDQJOHRIÛÛRUÛ
Internal Projector Designed in Human Engineering
Ceramics are separately built in around the cervical vertebrae as the acupressure load can be equally distributed due to the design that the internal projector can be rotated in a certain angle to the up/down/left/right.
Conveniently Designed External Projector
External projector is designed in a size conveniently held and used with a hand, which can be stored in a projector pocket nicely during no use.
Internal Driving Method with Low Noises
There are few noises thanks to the minimized friction between the internal projector and rail due to the specially designed guard rail which can be used semi-permanently by minimizing the driving load.
Convenient Remote Controller Holder
7KHUHPRWHFRQWUROOHUKROGHUSRVVLEOHRIÛURWDWLRQFDQEHXVHGFRQYHQLHQWO\LQDQ\ desired angle by the user.
Multifunctional Remote Controller Integrated into One
Buttons in a size that can be identified at a glance are easy to use with less wear due to the special materials, and button descriptions cannot be easily erased.
Special Heater and Tourmanium
The tourmanium mat is combined to the special heater.
NM-5000
Guide and Sequence for Product Installation
1
How to refer to cautions for safety
Refer to cautions to be kept during the product use.
(Refer to Page 3 in this User Manual for more details.)
4
How to Install the Product
(Refer to Page 24 in this User Manual for more details.)
2 How to check out the product components
(Refer to Page 10 in this User Manual for more details.)
5 How to use the product
(Refer to Page 28 in this User Manual for more details.)
3
How to Assemble the
Product Frame
(Refer to Page 20 in this User Manual for more details.)
Product Introduction
Product Components
i
Introduction
Please check out whether all the components are in hand before installing the product.
Please inquire of your supplier if there is any missing or damaged component.
Some specifications and/or designs are subject to change for improving the product performance.
Main mat Sub mat External projector Projector pocket
Product frame Remote controller Remote controller holder
(included in the frame packing box)
External cloth Low frequency pad Abdominal band for low frequency pad
Towel for low frequency pad
[ ENGLISH ] http://www.nuga.kr
Projector covers Connection cable for sub mat
Power cord
NM-5000
User Manual
Thank you for purchasing this product.
Before use...
Please read through cautions for safety in the user manual to use this product safely.
Quality Warranty Enclosed
Tourmanium Product
User manual
NM-5000
Product Frame Components
Handle frame(2EA) Frame legs(4EA)
Main base frame Frame leg fixing pipe
Main angle frame Sub angle frame
Product Introduction
Screws and components for assembly
9
Buffer rubbers
9
L-wrench
9
Bolt A
NM-5000
9
Bolt D
9
Spanner tool(M12, 13)
9
Set screw bolt C
9
Nut B
Product Introduction
Names and Functions of
Product Components
ⴘ The connection for the power
supply on the main assembly
and the power input to the
special heater
ྡ Internal projector
ྠ Product frame
ྟ Remote controller and its holder
NM-5000
ྞ
ྛ Low frequency pad
External projector
and projector pocket
ྚ Sub heater
HIGH
LOW
ྜ Temperature setter
for sub heater
ྜྷ Connector bay
Name Function
ྙ The connection for the power supply on the main assembly and the power input to the special heater
The power supply and signals are exchanged by connecting the power supply cable to both the main mat and sub mat.
ⴙ Sub heater
The sub heater positioned on top of the sub mat increases the heating effects by combining the tourmanium mat.
Low frequency pad has various functions including the relief from pain, etc.
ⴚ Low frequency pad ⴛ Temperature setter for
sub heater ⴜ Connector bay
Temperature can be set by turning a dial to the desired position.
ⴝ External projector
and projector pocket
A remote controller, external projector and low frequency pad are connected to the main assembly.
External projector is designed in a size conveniently held and used with a hand, which can be stored in a projector pocket nicely during no use.
ⴞ Remote controller and
its holder ⴟ Product frame ⴠ Internal projector
Buttons in a size that can be identified at a glance are easy to use and button descriptions cannot be easily erased due to the use of special
PDWHULDOV,QDGGLWLRQWKHUHPRWHFRQWUROOHUKROGHUSRVVLEOHRIÛURWDWLRQ can be used conveniently in any desired angle by the user.
Both the main mat and sub mat are horizontally built, which can be used more conveniently with the attachment of a handle to be controlled in step
UHVSHFWLYHO\IRUWKHGHVLUHGDQJOHRIÛÛRUÛ
Ceramics are separately built in around the cervical vertebrae as the acupressure load can be equally distributed due to the design that the internal projector can be rotated in a certain angle to the up/down/left/right. In addition, there are few noises thanks to the minimized friction between the internal projector and rail due to the specially designed guard rail which can be used semi-permanently by minimizing the driving load.
Product Introduction
Descriptions for Remote
Controller Buttons
POWER
Power button
Button to turn on/off the power supply for the product and internal projector
AUTO
Auto/Manual
Switch Button
Button to set the operating mode for the internal projector to Auto/Manual
Button to set the operating mode for the internal projector to
Auto/Manual
Window to display temperature and error message of internal projector
(refer to Page 41 for error messages)
Temperature
Control Button for
Internal Projector
Button to increase or decrease temperature of internal projector
Manual Mode
Button for Internal
Projector
Button to adjust the position of internal projector up/down during the manual mode setting
P LOW FREQ
/ 6 (" # &45
PROJECTOR
Power Button for
External Projector
Button to turn on/off the power supply for the external projector
LOW FREQ
Power Button for
Low Frequency
Pad
Button to turn on/off the power supply for the low frequency pad
Indicator Window for Temperature and Condition of
External Projector
Window to display temperature and error message of external projector (refer to Page 41 for error messages)
Temperature
Control Button for External
Projector
Button to increase or decrease temperature of external projector
CONT
Button to control the strength of low frequency
Button to control the strength of low frequency to a range of strong ~ weak in the low frequency pad
NM-5000
NM-5000
Product Installation and
Preparations
Before the Product Installation
How to Assemble the Product Frame
How to Install the Product
Test Operations after Installation
18
20
24
26
Before the Product Installation
Install the product in a flat floor.
Otherwise, it might damage the product.
Do not drop or shock the product.
Otherwise, it might damage the product.
Check out the applied voltage before any use.
Otherwise, it is likely that the electrical shock or fire occurs.
Do not place any inflammable substance on the product, such as candle light or cigarette light.
Otherwise, it is likely to cause the electrical shock or fire.
Avoid using the product in a closed place with any fuel and/or chemical.
Otherwise, it might cause injuries or fire.
Move the product after separating the power supply from connecting lines if the product is moved.
NM-5000
Connect the power supply after connecting the remote controller first.
Otherwise, it might cause damage to the product.
Do not install the product in a place with the frequent access.
(Otherwise, the product might be damaged.)
Do not install the product in a place with much moisture or water.
(Otherwise, the product might be damaged.)
Be careful not to expose the product to the direct sunlight.
(Otherwise, the product might be damaged.)
Product Installation and Preparations
How to Assemble the Product Frame
Frame legs
Handle frame
Frame legs
Frame leg fixing pipe
How to connect frame legs to the handle frame.
Insert frame legs (2 pieces) into the handle frame as shown in the picture.
Please note that the instructed corner direction should be oriented to the same direction during the insertion.
Assemble frame legs and the handle frame in the same way.
How to fix frame legs.
Fix 2 pieces of frame leg fixing pipes with 4 pieces of bolt A as shown in the picture and then fix it with a piece of L-wench (T-1).
Do not fasten bolts completely here.
Bolt A
L-wrench
T-1
Frame leg fixing pipe
Bolt A
Main base frame
Nut B
Main base frame
Fix the main base frame with bolt A (16 pieces) and nut B
(16 pieces) using an L-wrench as shown in the picture.
Do not fasten bolts completely here.
Bolt A
Nut B Bolt A L-wrench
T-1
NM-5000
Set screw bolt C
Hook
Nut B
Main base frame ⲱ2Ⲳ
Main angle frame
How to fix the main angle frame
Place the main angle frame on the base frame as shown in the picture.
Fasten a set screw bolt C (1 piece) and nut B (2 pieces) after inserting the hook into ‘Q’ here.
Completely fasten screws here, which have not been completely fastened in No. 3 assembly sequence.
Set screw bolt C
Sub angle frame
Hook
Nut B ⲱ2Ⲳ
Set screw bolt C Nut B
How to fix the sub angle frame.
Place the sub angle frame on the base frame as shown in the picture.
Fasten a set screw bolt C (1 piece) and nut B (2 pieces) after inserting the hook into ‘Q’ here.
Completely fasten screws here.
ⲱ3Ⲳ
Set screw bolt C Nut B
Insert the buffer rubbers into ‘R’’ in the picture.
How to insert the buffer rubbers.
Buffer rubbers
Product Installation and Preparations
How to Assemble the Product Frame
Bolt D
Nut B
How to fix the entirely assembled frame.
Fix the frame by fastening bolt
D (2 pieces) and nut B
(2 pieces) after setting the main base frame, main frame and sub frame as shown in the picture.
Nut B Bolt D
NM-5000 ⲱ4Ⲳ ⲱ4Ⲳ
How to assemble the remote controller holder.
Fasten bolt A (1 piece) and nut B (1 piece) after inserting the remote control holder into the instructed ‘S’ position.
Nut B Bolt A
L-wrench
T-1
How to fix the entire bolts again.
Fasten the entire bolts and nuts tightly once again after the assembly is completed.
Completed appearance
Product Installation and Preparations
How to Install the Product
Tighten the product frame to the mat
Attach the connecting band after placing and tightening both the main and sub mats to the product frame.
Prepare product components
Take out the remote controller, power cord, external projector, projector pocket, and low frequency pad.
NM-5000 ⴘⴙⴚ
Connect to the connector bay
ྙ Remote controller
ྚ External projector
ྛ Low frequency pad
Connect components sequentially.
Caution
Keep the groove upward to the cable connection.
Malfunctions might occur, if the groove is not aligned accurately during the cable connection.
Connect the mat cable
Connect the power supply cable for the sub mat to both the main and sub mats as shown in the picture.
Turn on the power supply in the product
Turn on the power switch after the power supply cord is connected to the power input on the side of the main mat.
Caution
Turn off the power switch when the power is connected.
Otherwise, it might cause failure.
Set temperature to the sub heater
Turn the dialer to set the desired temperature in the sub heater attached to the side of the sub mat.
HIGH
LOW
Product Installation and Preparations
Test Operations after Installation
Check out the power supply for the product
Turn on the power switch.
Caution
Ensure the power supply to be turned off after use or during no use.
Otherwise, it might cause failure.
Off On
Power switch in the main assembly ⴘ
POWER AUTO ⴙ
AUTO
TEMP
MANUAL
MANU
Controller for main assembly
PROJECTOR LOW FREQ
PJT ⴚ
Controller for external projector
Check out operations of remote controller
ྙ Press the power button on the
remote controller
ྚ Adjust temperature for the internal projector (+ / – button)
ྛ Adjust temperature for the external projector (+ / – button)
Refer to ‘How to Use the Remote
Controller’ for each mode
(Page 28)
HIGH
LOW
Check out operations of sub heater
Turn the dialer to set the desired temperature in the sub heater attached to the side of the sub mat.
Use the product
Lay yourself down with your legs toward the sub mat and press the
Auto button in the remote controller for the automatic operations in the product.
You may use the product while laying yourself down the other way around.
NM-5000
NM-5000
How to Use the Product
How to Use the Remote Controller
How to Use the Product by Mode
How to Use the External Projector
How to Use the Low Frequency Pad
How to Use the Product
How to Set Temperature for the Sub Heater
28
28
33
34
36
38
How to Use the Remote Controller
- How to Use the Product by Mode
Auto ྙ Mode
Round-trip acupuncture function
POWER AUTO
AUTO
TEMP
MANUAL
MANU
PROJECTOR LOW FREQ
PJT
TEMP
Mid
Min
CONT
Max
L/F
/ 6 (" # &45
Power supply
POWER AUTO
AUTO
TEMP
MANUAL
MANU ⴘ Press the power button.
· Check out the connecting conditions
of the remote controller.
· Press the power button once : On
Press it once again : Off
Auto ྙ Mode
POWER AUTO
AUTO
TEMP
MANUAL
MANU
ྚ Press the Auto button to operate
the internal projector.
No separate operation is necessary
in the middle as the product stops
automatically after operations.
The product automatically stops after round-trip acupuncture operations for about 38 minutes.
Temperature control
POWER AUTO
AUTO
TEMP
MANUAL
MANU
ྛ Control temperature with +/- button.
(Moderate temperature: 55~60 )
· Range of temperature setting for
internal projector: 40~70
· Temperature setting unit
40~55 : Temperature setting per 5
55~70 : Temperature setting per 1
NM-5000
POWER AUTO
AUTO
TEMP
MANUAL
MANU
PROJECTOR LOW FREQ
PJT
Min
TEMP
Mid
CONT
Max
L/F
/ 6 (" # &45
Auto ⴙ Mode
Round-trip massage function
Power supply
POWER AUTO
AUTO
TEMP
MANUAL
MANU ⴘ Press the power button.
· Check out the connecting conditions
of the remote controller.
· Press the power button once : On
Press it once again : Off
POWER AUTO
AUTO
TEMP
MANUAL
Auto ⴙ Mode
ྚ Press the Auto button twice in a
row to operate the internal projector.
No separate operation is necessary
in the middle as the product stops
automatically after operations.
MANU
The product automatically stops after round-trip massage operations for about
38 minutes.
Press the Auto button to operate Auto
ྚ Mode while Auto ྙ Mode is operating.
Temperature control
POWER AUTO
AUTO
TEMP
MANUAL
MANU
ྛ Control temperature with +/- button.
(Moderate temperature: 55~60 )
· Range of temperature setting for
internal projector: 40~70
· Temperature setting unit
40~55 : Temperature setting per 5
55~70 : Temperature setting per 1
How to Use the Product
How to Use the Remote Controller
- How to Use the Product by Mode
Auto ྛ Mode
Massage function between the thoracic vertebrae and cervical vertebrae
POWER AUTO
AUTO
TEMP
MANUAL
MANU
PROJECTOR LOW FREQ
PJT
TEMP
Mid
Min
CONT
Max
L/F
NUGA BES
T
Power supply
POWER AUTO
AUTO
TEMP
MANUAL
MANU ⴘ Press the power button.
· Check out the connecting conditions
of the remote controller.
· Press the power button once : On
Press it once again : Off
POWER AUTO
AUTO
TEMP
MANUAL
MANU
Auto ྛ Mode ⴙ 3UHVVŸEXWWRQWZLFHLQDURZWR operate the internal projector. No separate operation is necessary in the middle as the product stops automatically after operations.
The product automatically stops after round-trip massage operations between the central thoracic vertebrae and cervical vertebrae for about 38 minutes.
Temperature control
POWER AUTO
AUTO
TEMP
MANUAL
MANU
ྛ Control temperature with +/- button.
(Moderate temperature: 55~60 )
· Range of temperature setting for
internal projector: 40~70
· Temperature setting unit
40~55 : Temperature setting per 5
55~70 : Temperature setting per 1
Auto ྜ Mode
Massage function between the thoracic vertebrae and vertebrae lumbales
POWER AUTO
AUTO
TEMP
MANUAL
MANU
PROJECTOR LOW FREQ
PJT
TEMP
Mid
Min
CONT
Max
L/F
NUGA BES
T
Power supply
POWER AUTO
AUTO
TEMP
MANUAL
MANU ⴘ Press the power button.
· Check out the connecting conditions
of the remote controller.
· Press the power button once : On
Press it once again : Off
POWER AUTO
AUTO
TEMP
MANUAL
MANU hGྜGt ⴙ 3UHVVźEXWWRQWZLFHLQDURZWR operate the internal projector. No separate operation is necessary in the middle as the product stops automatically after operations.
The product automatically stops after round-trip massage operations between the central thoracic vertebrae and vertebrae lumbales for about 38 minutes.
Temperature control
POWER AUTO
AUTO
TEMP
MANUAL
MANU
ྛ Control temperature with +/- button.
(Moderate temperature: 55~60 )
· Range of temperature setting for
internal projector: 40~70
· Temperature setting unit
40~55 : Temperature setting per 5
55~70 : Temperature setting per 1
NM-5000
How to Use the Product
POWER AUTO
AUTO
TEMP
MANUAL
MANU
PROJECTOR LOW FREQ
PJT
TEMP
Mid
Min
CONT
Max
L/F
NUGA BES
T
Manual Mode Power supply
POWER AUTO
AUTO
TEMP
MANUAL
MANU ⴘ Press the power button.
· Check out the connecting conditions
of the remote controller.
· Press the power button once : On
Press it once again : Off
Manual Mode
POWER AUTO
AUTO
TEMP
MANUAL
.PWJOH
QBUI
MANU
ྚ Use the product after placing the
internal projector at the desired
position with manual button
ŸźGXULQJWKHPDQXDOPRGH
The internal projector moves
ZKLOHŸźLVEHLQJSUHVVHG
Ÿ7KHLQWHUQDOSURMHFWRUPRYHV
to the cervical vertebrae.
ź7KHLQWHUQDOSURMHFWRUPRYHV
to the vertebrae lumbales.
POWER AUTO
AUTO
TEMP
MANUAL
Temperature control
MANU
ྛ Control temperature with +/- button.
(Moderate temperature: 55~60 )
· Range of temperature setting for
internal projector: 40~70
· Temperature setting unit
40~55 : Temperature setting per 5
55~70 : Temperature setting per 1
NM-5000
POWER AUTO
AUTO
TEMP
MANUAL
MANU
PROJECTOR LOW FREQ
PJT
TEMP
Mid
Min
CONT
Max
L/F
NUGA BES
T
How to Use the Remote Controller
- How to Use the External Projector
Operations
PROJECTOR LOW FREQ
PJT
TEMP
Mid
Min
CONT
Max
L/F
ྙ Press the projector button.
· Check out the connecting conditions
of the projector.
· Press the projector button once: On
Press it once again: Off
PROJECTOR LOW FREQ
PJT
Min
TEMP
Mid
CONT
Max
L/F
Temperature control
ྚ Control temperature with +/- button.
(Moderate temperature: 55~60 )
· The projector is not turned on of the
actual temperature is higher than the
setting temperature, which is not meant
to be any failure.
· Temperature setting unit
40~55 : Temperature setting per 5
55~70 : Temperature setting per 1
Applied to the specific area
ྛ Apply to the desired area.
· Put the projector covers on before
applying it.
Caution
ྜ Ensure the projector covers to
be covered while the external
projector is being used.
· Be aware that any direct contact
from the projector to the skin during
the high temperature setting might
cause burns.
How to Use the Product
How to Use the Remote Controller
- How to Use the Low Frequency Pad
Connection
Towel for the low frequency pad
Surface to contract the belly
What is the low frequency pad?
The low frequency pad is a device to improve scleritic pain or amyotrophia by applying weak current to the human body.
ྙ Connect an abdominal band to the
hole in both sides of the low
frequency pad.
ྚ Wear the low frequency pad and
abdominal band after wetting the
towel for the low frequency pad or
a piece of 100% cotton towel or
cloth with water, and placing it on
the belly before wearing the low
frequency pad, if there is no gel at
home.
· Use a piece of towel or cloth after
squeezing it out completely to
prevent it from flowing water when it
is wetted with water.
ྛ Wear the abdominal band after
fixing the low frequency pad in a
good manner.
Various wearing methods
You may wear it around any area other than the abdominal area.
NM-5000
POWER AUTO
AUTO
TEMP
MANUAL
MANU
PROJECTOR LOW FREQ
PJT
TEMP
Mid
Min
CONT
Max
L/F
NUGA BES
T
PROJECTOR LOW FREQ
PJT
TEMP
Mid
Min
CONT
Max
L/F
Power supply
ྜ Press the low frequency button to
turn on the power supply for the low
frequency pad.
(Initial setting is set to ‘Weak 1’.)
· Check out the connecting conditions
of the low frequency pad.
· Press the low frequency button once: On
Press it once again: Off
PROJECTOR LOW FREQ
Strength control ⴜ Control the strength of low
frequency with the strength
button. (Refer to the following.)
PJT
Min
TEMP
Mid
CONT
Max
L/F
PJT
TEMP
Mid
Min
CONT
Max
L/F
Weak 1:
Green lighting
PJT
TEMP
Mid
Min
CONT
Max
L/F
Middle 1:
Yellow lighting
PJT
Min
TEMP
Mid
CONT
Max
L/F
PJT
TEMP
Mid
Min
CONT
Max
L/F
Weak 2:
Green blinking
PJT
TEMP
Mid
Min
CONT
Max
L/F
Middle 2:
Yellow blinking
PJT
TEMP
Mid
Min
CONT
Max
L/F
Strong 1:
Red lighting
Strong 2:
Red blinking
The low frequency pad automatically stops after operations for about 40 minutes.
How to Use the Product
How to Use the Product
Normal direction
Basic use ⴘ Lay yourself down with the head to the
main mat and legs to the sub mat.
ⴙ Apply massage to your desired area
such as your arms with the external
projector during the Auto mode.
ⴚ Use the product while you are laying
yourself down to the opposite side.
Reverse direction
Caution
Ensure using the projector covers while applying the external projector.
Be aware of burns if the product is applied to a part in the human body for a long time.
Angle control can be done to both directions.
How to control angle
ྙ 6WHSZLVHFRQWUROE\ÛFDQEHGRQHZLWK
ÛÛRUÛLIWKHPDWDQJOHLVVHW
upward.
· Grab the product frame at the mat bottom
and then control stepwise to set upward.
ྚ Pull down attached to the product frame
if you want the mat angle downward.
Set angle upward Set angle downward
Hook handle
NM-5000
How to use while sitting
ྙ Apply massage with the external
projector after operating the product
in the same way as the basic use.
ྚ Use the product after controlling temperature
for the sub mat while operations for the
main mat is being stopped.
Main mat heating
Sub mat heating
Caution
Ensure using the projector covers while applying the external projector.
Be aware of burns if the product is applied to a part in the human body for a long time.
Apply the proper temperature while using the sub heater.
Simultaneous use for 2 persons
ྙ Two persons can use the product
simultaneously with one person on the
product and another person with the
external projector while sitting.
Caution
Ensure using the projector covers while applying the external projector.
Be aware of burns if the product is applied to a part in the human body for a long time.
How to apply to the abdominal area
Main mat heating
Sub mat heating
ྙ Lie on your face with the head to the
main mat and legs to the sub mat.
ྚ Press the button with the remote controller
to move the internal projector to the
abdominal area. Lie on your face after
moving to the abdominal area.
ྛ Apply the heating function to the abdominal
area using the sub heater while laying
yourself down to the opposite direction.
Stop operating the main mat during this time.
Caution
Do not apply the product to the breast but only to the abdominal area manually during
PDVVDJHWRWKHDEGRPLQDODUHD2WKHUZLVHLW might cause damage to the human body.
How to Use the Product
How to Set Temperature for the Sub Heater
Sub heater
NM-5000
HIGH
LOW
Temperature setter for sub heater
How to use temperature setter for sub heater
HIGH
LOW
Turn the dial to the desired position to set temperature.
(30~65 )
NM-5000
Product Storage and Care
How to Store and Clean the Product after Use
Check Indicator Window of Remote Controller
How to Take Emergency Actions during Use
Self-check Items
Before any A/S Request
Product Specifications
Memo
Product Warranty
44
45
46
47
40
41
42
43
How to Store and Clean the Product after Use
i
Introduction
6HSDUDWHWKHSRZHUFRUGZKLOHWKHSURGXFWLVQRWEHLQJLQXVHIRU
DORQJWLPH
%HDZDUHRIWKHIROORZLQJIRUWKHVWRUDJHSODFH
ྙ .HHSWKHSURGXFWLQDSODFHZLWKQRZDWHU
ྚ .HHSWKHSURGXFWLQDSODFHZLWKQRFRQFHUQRIDQ\DGYHUVHHIIHFWVXFKDVWKHDLU
SUHVVXUHWHPSHUDWXUHKXPLGLW\YHQWLODWLRQVXQOLJKWDQGRUDLUFRQWDLQLQJGXVW
VDOWVXOIXUHWF
ྛ %HFDUHIXORIVDIHW\FRQGLWLRQVVXFKDVWKHVORSHYLEUDWLRQVKRFNHWF
LQFOXGLQJWKRVHGXULQJWUDQVSRUWDWLRQ
ྜ 'RQRWNHHSWKHSURGXFWLQDSODFHWRVWRUHDQ\FKHPLFDORUJDV
ྜྷ $YRLGDQ\GLUHFWVXQOLJKWGXULQJWKHVWRUDJH
6WRUHWKHSURGXFWDIWHUDUUDQJLQJFRPSRQHQWVFOHDQ
Environmental conditions
'XULQJRSHUDWLRQV7HPSHUDWXUHa KXPLGLW\a
7UDQVSRUWDQGVWRUDJHFRQGLWLRQV7HPSHUDWXUHa KXPLGLW\a
DWPRVSKHULFSUHVVXUHK3DWRK3D
How to clean
Caution
(QVXUHXQSOXJJLQJWKHSRZHUSOXJEHIRUHFOHDQLQJ
2WKHUZLVHLWPLJKWFDXVHHOHFWULFVKRFNV
Mat cover
:LSHRXWWKHPDWFRYHUZLWK
ZD[IRUOHDWKHUVHDWRUGU\FORWK
External cloth
6HSDUDWHDQGFOHDQ
WKHH[WHUQDOFORWK
Product frame
$SSO\DOLWWOHRIZDWHUWRGU\FORWK
DQGVRIWO\ZLSHLWRXW
NM-5000
Check Indicator Window of Remote Controller
POWER AUTO
AUTO
TEMP
MANUAL
MANU
PROJECTOR LOW FREQ
PJT
TEMP
Mid
Min
CONT
Max
L/F
PROJECTOR LOW FREQ
PJT
Min
TEMP
Mid
CONT
Max
L/F
POWER AUTO
AUTO
TEMP
MANUAL
MANU
Caution
'RQRWGLVDVVHPEOHWKHSURGXFWDUELWUDULO\LIDQ\HUURURFFXUVEXWUHPRYHWKHSRZHU
SOXJWXUQRIIWKHSRZHUVZLWFKDQGWKHQFRQWDFW\RXUVXSSOLHU
,I\RXGLVDVVHPEOHWKHSURGXFWDUELWUDULO\LWPLJKWFDXVHVHULRXVLQMXULHVDQGRUGDPDJH
WRWKHSURGXFW
'LVSOD\ 'HVFULSWLRQV 'LVSOD\ORFDWLRQ
POWER AUTO
AUTO
TEMP
MANUAL
MANU
$EQRUPDOWHPSHUDWXUHVHQVRU
LQWKHLQWHUQDOSURMHFWRU
Indicator window for the
LQWHUQDOSURMHFWRUFRQGLWLRQV
'LVFRQQHFWLRQRIODPS
LQWKHLQWHUQDOSURMHFWRU
Indicator window for the
LQWHUQDOSURMHFWRUFRQGLWLRQV
$EQRUPDOWHPSHUDWXUHVHQVRU
LQWKHH[WHUQDOSURMHFWRU
Indicator window for the
H[WHUQDOSURMHFWRUWHPSHUDWXUH
'LVFRQQHFWLRQRIODPS
LQWKHH[WHUQDOSURMHFWRU
Indicator window for the
H[WHUQDOSURMHFWRUWHPSHUDWXUH
'LVFRQQHFWLRQRIWKH
XSSHURUORZHUOLPLWVZLWFK
Indicator window for the
LQWHUQDOSURMHFWRUFRQGLWLRQV
3URGXFW6WRUDJHDQG&DUH
How to Take Emergency
Actions during Use
Stop using the product immediately and remove the power plug if there is any lightning.
Stop using the product immediately and contact your supplier branch or our company if you smell any burn or detect any smoke from the product.
Stop using the product immediately and consult with a doctor if any abnormality occurs from the human body.
Turn off the power switch immediately, stop using the product and contact our company if you find out any failure or power failure from the product.
Turn off the power switch, remove the power plug immediately, and then contact our company if you pour water into the water.
NM-5000
Self-check Items
Caution
There might be concerns of injuries or fire if you fail to check out the following. Make sure that you check out the following.
Check before use
1. Is the power cord connected to a socket?
Yes No
2. Is the remote controller operating well?
Yes No
3. Is the temperature indication displayed on the
temperature indicator window on the remote controller?
Yes No
4. Is the temperature of the projector not too high?
Yes No
5. Is the temperature of the sub heater not too high?
Yes No
6. Is the power supply for both the internal and external
projectors turned on?
Yes No
7. Did you check out conditions for any damage to the
power cord or cable conditions?
Yes No
Check after use
1. Is the temperature on the temperature indicator
window on the remote controller turned off?
2. Is the operating lamp on the remote controller
turned off?
3. Is the power lamp on the projector turned off?
4. Is the power switch turned off to the point?
5. Is the power cord separated from the socket?
Yes No
Yes No
Yes No
Yes No
Yes No
Product Storage and Care
Before any A/S Request
Caution
Ensure checking out the following before applying for A/S if any abnormality occurs from the product.
The product might fail to operate normally even without any failure if you use it with no right understanding on how to use it.
Checklist for any abnormality on the remote controller
If various indicator lamps on the remote controller are not operating;
If you see a warning message "1E”;
ྙ Turn on the main power switch.
ྚ Check out if the power cord is accurately connected.
ྛ Check out if the fuse inside the main power switch is
disconnected.
ྜ Check out if other operating keys are pressed on the
remote controller.
It is a safety message due to failure in the heating lamp for the internal projector.
The product will operate if you replace the heating lamp.
Do not disassemble the product but contact your nearest supplier or A/S center.
If you see a warning message "3E”;
It is a safety message due to failure in the heating lamp for the external projector.
The product will operate if you replace the heating lamp.
Do not disassemble the product but contact your nearest supplier or A/S center.
Checklist for any abnormality on the internal projector
If the internal projector is not operating;
ྙ Check out if the power cord is accurately connected.
ྚ Connect the connector for the remote controller again.
Do not disassemble the product but contact your nearest supplier or A/S center.
Checklist for operations of the low frequency pad
If the low frequency pad is not operating;
Check out if the connector for the low frequency pad is connected accurately.
NM-5000
Product Specifications
Product name and model name
Manufacturer
Thermal massage bed
NM-5000
NUGA MEDICAL CO., LTD.
185, Jiraeul-ro, Jijeong-myeon, Wonju-si,
Gangwon-do, Korea
Date of manufacture / number of manufacture
Marked on the product
Product weight
Product size
Main box: 31 kg
Subsidiary box: 13 kg
Product frame box: 35 kg
Main mat: 1220 X 615 X 170 (mm)
Sub mat: 790 X 610 X 147 (mm)
Product frame: 1980 X655 X 560 (mm)
Cautions during use
Refer to the user manual
Operating method
Refer to the user manual
Electric rating
AC 220–240V~, 50–60Hz
Power consumption
250 W
Product Storage and Care
Memo
NM-5000
Download
Public link updated
The public link to your chat has been updated. You may view and manage your chat links after registration here.
Document public link
Advertisement
