BITMAIN

S4 Server Manual

S4 Server

Manual

Last updated: 9/29/2014

Page 2 of 8

Contents

1 Overview ................................................................................................................................... 3

2 Connect to

Server

...................................................................................................................... 3

3

Server

Configuration .................................................................................................................. 4

3.1 Pool Setting ................................................................................................................... 4

3.2 Frequency Modification ................................................................................................ 5

4

Server

Status .............................................................................................................................. 5

5 System Configuration and status ............................................................................................... 6

5.1 System Upgrading ......................................................................................................... 6

5.2 Password Modification .................................................................................................. 6

5.3 Software Version Checking ............................................................................................ 7

5.4 Restore Initial Setting .................................................................................................... 7

Page 2 /

8

S4 Server

Manual

Last updated: 9/29/2014

Page 3 of 8

1 Overview

The

S4 Server

is a chassis style 2TH/s bitcoin server

with PSU. It has been assembled before Fab out.

PSU inside: 1400W, 80PLUS gold, C14 input socket. Power line not included. You may look for one line with no less than 16A in your local market.

LCD screen: Here shows IP address, Hashrate, Max temperature. There are also status LEDS, reset button and beep on the screen.

Casing size: 3U Rack, 432mm*442mm*133mm.

2 Connect to

Server

Step 1. The default DHCP network protocol distributes IP addresses automatically.

After you have your server

hooked up, you will see the IP address on the LCD display.

Step 2. Connect your server

to the PC with network cable.

Step 3. Enter server

’s IP address into your web browser, then login in to the server

console.

The default username and password for S4 is ‘root’.

Through ‘Network’, you will be able to modify the server's

IP address, and choose ‘Save and

Apply’ after modifying it.

Page 3 /

8

S4 Server

Manual

Last updated:

9/29/2014 Page 4 of

8

3

Server

Configuration

3.1

Pool Setting

You can configure your server

through ‘ Configuration->General Settings‘.

Pool URL- In this column you should enter the URL of your desired pool.

Worker- This is your worker ID on the selected pool.

Password- This is the password for your selected worker.

Comment:

3.1.1

Server

can be set up with three mining pools, the priority decreases from first pool (pool 1) to third pool (pool 3). The pool with low priority will start to work only when the high priority pool breaks down.

3.1.2 With ‘Beeper ringing’ checked, beeper will ring when the server

stops mining, otherwise it won’t ring even if the server

stops mining.

3.1.3 With ‘Stop running when temperature is over 80 ℃ ’ checked, the server

will stop mining when the temperature exceeds 80 ℃ ’ to protect the server

. If it ’s unchecked, the server

will still mine even in high temperature.

Click ‘Save & Apply’ to save and restart server

.

Page 4 /

8

S4 Server

Manual

Last updated: 9/29/2014

Page 5 of 8

3.2

Frequency Modification

You are able to modify the frequency value through ‘Configuration->Advanced Settings‘. E.g.:

Voltage ‘0720’ means operating voltage of chip is 0.72V. Voltage needs to be modified when adjusting the frequency.

4

Server

Status

Click the status marked below

, you can check the operating status of your server

.

ASIC#: ASIC number in the chain

Frequency: ASIC setting frequency

Temp: Temperature, centigrade

ASIC status: o stands for OK, x stands for error.

Page 5 /

8

S4 Server

Manual

Last updated: 9/29/2014

Page 6 of 8

5 System Configuration and status

5.1

System Upgrading

Through ‘System->Upgrade’, you will be able to upgrade your serv er.

‘Keep setting’ is chosen by default, you should choose it if you hope to preserve the current settings.

You should cancel this option if you hope to restore to initial settings.

Click ‘Browse’ button to choose upgrade file. After choosing upgrade file, then click ’Flash image...’ button, it will remind if upgrading software, start to download software after choosing upgrading software. During the upgrade process, you need to wait patiently, and must keep power on, otherwise, the server

should be shipped to factory to restore.

You will see bellow screenshot after upgrading successfully.

Choose ‘Reboot’ button, server

will restart and run the new system. Choose ‘Go Back’, server will continue running the old system, will run new system when power on next time.

5.2

Password Modification

Through ‘System->Administration’, you can modify AntMiner login password, and choose ‘Save’ and ‘Save and Apply’ after modifying it.

Page 6 /

8

S4 Server

Manual

Last updated: 9/29/2014

Page 7 of 8

5.3

Software Version Checking

Through ‘System->Overview‘, you will be able to check the software version you used.

After upgrading the software, to check if you are using the latest version of software via ‘File

System Version’.

5.4

Restore Initial Setting

Press the ‘Reset’ button on the left bottom of LCD screen and hold on for 3 seconds, red led flashing every one second/1S. Release ‘Reset’ button, the server

will restore the initial setting and restart automatically.

Page 7 /

8

S4 Server

Manual

Last updated: 9/29/2014

Page 7 of 8

Page

8

/

8