advertisement
![Vigitron OmniiCopper Vi27000 Series Installation Manual | Manualzz Vigitron OmniiCopper Vi27000 Series Installation Manual | Manualzz](http://s2.manualzz.com/store/data/060093168_1-1f394462a94af91cee0ac693d990a7b8-360x466.png)
Vi27004 4-Port
Single-Pair Ethernet & PoE Transmission Solution Installation Manual
Ethernet Extenders
TM
Application Drawing
Network Switch
The OmniiCopper™ Vi27000 series is a revolutionary data transmission solution that extends full-duplex High-Speed Ethernet and PoE over single pair wire infrastructures. The Vi27000 is a transmitter that operates in conjunction with 1-port Vi27001 or 4-port Vi27004 receivers over virtually any 2 conductor wires reliably. The Vi2700X’s unique transmission technology eliminates the potential for cross talk resulting in the perfect solution for bundled cable runs used in many elevator and building communication systems.
Up to 36W power can be provided from a PoE source at each port to eliminate the need for a local power supply at the camera location. Vi27004 requires a
12VDC power supply to operate. The Vi27004 operates at extended temperature range -30°C to +50°C.
Installation cost savings, tested and proven design and performance go into making the Vi27000 series the perfect solution for building CCTV wiring.
Data + PoE
Cat5/6
Vi27000
PoE Camera
Data + PoE
Cat5/6
Vi0014
Data + PoE
Single Pair Wire
Data + PoE
Single Pair Wire
Vi27000
PoE Camera
Data + PoE
Cat5/6
Vi1120/Vi0017
Both the Vi27004 and the Vi27000 can use local power supplies to power themselves and provide PoE to the IP camera .
Elevator
Vi27000
PoE Switch
Data + PoE
Cat5/6
Important Safety Warning
- Read these instructions.
- Keep these instructions.
- Heed all warnings.
- Follow all instructions.
- Do not use this apparatus near water.
- Clean only with a dry cloth.
- Install in accordance with the manufacturer’s instructions.
- This installation should be made by a qualified service person and should conform
to all local codes.
- DO NOT bundle low-voltage signals in the same conduit as high-voltage wiring.
- To reduce the risk of fire or electrical shock, do not expose these products to rain,
moisture, dripping or splashing.
- No objects filled with liquids, such as vases, shall be placed on Vigitron equipment.
- DO NOT install the unit in a place where the operating ambient temperature
exceeds 50°C.
- Make sure that the external power supply output voltage is in the recommended range.
- Do not install near any heat sources such as radiators, heat registers, stoves or
other apparatus (including DVRs) that produce heat.
- Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
- Only use attachments/accessories specified by the manufacturer.
- Unplug this apparatus during lightning storms or when unused for long periods of time.
- Refer all servicing to qualified service personnel. Servicing is required when the
apparatus has been damaged in any way, such as a power supply cord or plug is
damaged, liquid has been spilled, or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, does not operate normally, or has
been dropped.
- The mains plug is used as the disconnect device and shall remain readily operable.
WARNING! - To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. This apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases shall be placed on the apparatus.
WARNING! - This apparatus is a Class I product. This product must be connected to a mains socket outlet thru an AC to DC Power supply.
WARNING! - The mains plug is used as the disconnect device and shall remain readily operable.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRICAL SHOCK,
DO NOT REMOVE COVER. NO USER SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
Vi0014
Data + PoE
Single Pair Wire
The Vi27000 series enables transmitting Ethernet and PoE over a wide veriaty of single pair wires and is ideal for Elevator Applications.
IP Camera-end Installation
- Install the Vi27000 “Remote Unit” near the Camera end.
- Connect the IP camera RJ45 connector to the 10/100BaseT Ethernet port of
Vi27000 using a standard Cat5/6 cable of maximum 100 m .
- Connect one end of the long Single Pair Wire to the 2-pin Terminal block of
Vi27000. Make sure the Single Pair Wire polarity matches on the Vi27004 End.
The link LED on the 10/100 connector should be “ON” to indicate proper connection between the camera and Vi27000.
The PoE LED on the 10/100 connector should be "ON" when PoE is used to power up the camera. The Status LED on the Single Pair Wire side should be “ON” and flashing to indicate proper connection.
Ethernet Switch-end Installation
- Install the Vi27004 “Local Unit” near the network switch.
- Power up the Vi27004 with 12VDC Power Supply.
- Connect the RJ45 connector of the Ethernet switch to the 10/100BaseT Ethernet
ports of Vi27004 using a standard Cat5/6 cable of maximum 100 m.
- Connect one end of the long Single Pair Wire to the to the 2-pin Terminal block of
Vi27004. Make sure the Single-Pair Wire polarity matches to the Vi27000 End.
The link LED on the 10/100 Ethernet connector should be “ON” and flashing to indicate proper connection between the switch and Vi27004 port. Also the Status
LED on the Single-Pair Wire side should be “ON” and flashing to indicate proper connection.
- The Vi27004 passes through PoE from PoE Switch to power the Vi27000 and
camera.
- If a PSE source such as a PoE network switch is not available, external power
must be provided to the Vi27000 by a local power supply.
CAUTION:
If an external power supply adaptor is plugged into Vi27000 or Vi27001, the unit will not use or pass thru PoE power from the PoE switch. It will use the power from the plugged in DC power supply.
The Power LED on the Vi27004 only indicates that the Vi27004 is powered up, it does not indicate the PoE is outputing. To View PoE Status, view indication on the
PoE switch on or PoE LED indicator on the Vi27000.
The Smart Choice for Transmission Solutions
www.vigitron.com
Technical Specifications* Ethernet Status LEDs
Electrical
Ethernet Interface Standard 10/100BaseT
Data Rate
Cable Type**
Power Supply
Power
Consumption
Auto select 10/100 Mbps
Single Pair 24/2 to 16/2 : Up to 3,000 feet (914m)
12 VDC, @ 1.5A (Min.)
14W using Local power supply
Status LEDs
Connectors
RFC
Power On : Green LED
Status : 4 x Blue LED
Standard Ethernet Traffic, Link,: 4 x Orange LED
Standard Ethernet : 4 x RJ-45 Connector
Single Pair Cable : 4 x Detachable 2-pin Terminal Block
Power: Barrel type DC005 5.5*2.1mm
2544 TCP/IP Packet Transmission
768 UDP, 2068 HTTP, 793 TCP
791 IP, 1783 TFTP, 894 IP over Ethernet
PoE Compatibility IEEE 802.3af, IEEE 802.3at
Regulatory
FCC
Safety
Environmental
Part 15, Subpart B, Class B 2010
CE
RoHS, WEEE
Environmental
Humidity
Temperature
0 to 95%, non-condensing
Operating: -30°C to +65°C per NEMA-TS2 testing
Storage: -40°C to +85°C
Mechanical
Dimensions
Weight
Material
1.66 x 4.08 x 4 inch, 4.2 x 10.4 x 10.2 cm (HxWxL)
0.758 lb, 344 g
Extruded Aluminum
Accessories
Vi0014 12VDC wall-mount power supplies (optional)
* Specifications subject to change without notice.
**Caution must be taken not to exceed the current capacity of the installed wire.
Actual performance will depend on type of cable and cable quality. Cables must be direct run as splices and jumpers will result in lower performance.
Data/PoE Distance
Vi27000 Series Data Rate Vs. Distance Chart
60
50
40
30
20
10
0
0
110
100
90
80
70
30
100 200 300 400 500 600 700 800 900 1000 1100 1200 1300 1400 1500 1600 1700 1800 1900 2000 3000
Distance (Feet)
Vi27000 Series PoE Power Vs. Distance***
25
20
15
10
5
0
0 100 200 300 400 500 600 700 800 900
24/2 AWG Twisted (Cat5)
20/2 AWG Untwisted
24/2 AWG Untwisted
18/2 AWG Untwisted**
22/2 AWG Untwisted
18/2 AWG Solid twisted
*** The 18/2 AWG Untwisted and 18/2 AWG Solid twisted overlap on PoE chart
The Vi2208 Midspan was used as PoE source.
PART No.
LED Name
Power
Status
Link/Act
PoE
(Remote Side)
Color Status
OFF
Function
Power is OFF
GREEN
BLUE
ORANGE
FLASHING Connection OK
OFF No connection
FLASHING Connection is OK with Traffic
OFF No PoE
GREEN
ON
OFF
Power is ON
No Connection
ON PoE is ON
Ordering Information
Description
Vi27000 1-Port Single-Pair Wire Ethernet & PoE Extender, Remote Unit
Vi27001 1-Port Single-Pair Ethernet & PoE Extender, Local Unit
Vi27004 4-Port Single-Pair Ethernet & PoE Extender, Local Unit
Drawings
TM
Link
4.08"
10.4 cm
Link
Limited Lifetime Warranty
Vigitron, Inc. warrants that all Vigitron products (“Product”), if used in accordance with these instructions, will be free of defects in material and workmanship for lifetime defined as the duration period of time until product end of life is announcement. After which Vigitron will continue to provide warranty services for a period of 3 years. Period covering valid warranty will be determined by proof of purchase in the form of an invoice from an authorized Vigitron dealer.
Vi27004
Stat
Stat
Link
Stat
Stat
Link
Ethernet & PoE Extender over Single Pair Wire
Front View
Local Unit
1.66"
4.2 cm
Warranty will only be provided for as long as the original end user purchaser owns the product.
Warranty is not transferrable. At Vigitron's option, defective product will be repaired, replaced or substituted with a product of equal value. This warranty does not apply if, in the judgment of
Vigitron, Inc., the Product fails due to damage from shipment, handling, storage, accident, abuse or misuse, or if it has been used or maintained not conforming to Product manual instructions, has been modified, or serial number removed or defaced. Repair by anyone other than Vigitron,
Inc. or an approved agent will void this warranty. Vigitron, Inc. shall not under any circumstances be liable to any person for any incidental, indirect or consequential damages, including damages resulting from use or malfunction of the product, loss of profits or revenues or costs of replacement goods. The maximum liability of Vigitron, Inc. under this warranty is limited to the original purchase price of the Product only.
RoHS
TEL (+1) 858 - 484 - 5209 • FAX (+1) 858 - 484 - 1205
7810 Trade Street, Suite 100, San Diego, CA 92121, USA • [email protected] • www.vigitron.com
© Copyright 2019 Vigitron, Inc.
UMVi27004_1119
advertisement
Related manuals
advertisement