advertisement
ASSEMBLY INSTRUCTIONS
The Cambridge Raised Planter Box
www.wearevita.com
90 cm
15 cm
Please read through before starting assembly.
91 cm 61 cm
Planter Box Dimensions are 32”L x 20”W x 10”D (81 cm L x 51 cm W x 25 cm D)
(± 3.7 cubic feet (0.1 cubic Meter) / 0.14 cubic yards / 105 litres)
Check Box for These Contents
In the event of missing or defective parts please call our customer service dept. at 1 800 282 9346 (Mon. to Fri. 8:00 AM to 5 :00 PM EST) .
1.
Pre-Assembled Side Wall Panels with Posts Connected (2) - 1087 3
2.
Floor Panels (4) - 10871
3.
Floor Support (1) - 10872
4.
Front and Back Wall Panels (2) - 1087 0
5.
Pre-assembled Shelf (1) - 10874
6.
Post Caps (4) - 10611
7.
5/8” (1.6 cm) Stainless Steel Screws (12) - 20016
8.
1 1/2” (4 cm) Stainless Steel Screws (8) - 20005
2
1
6
General Information
• Read Instructions through carefully before beginning assembly.
• When assembling components, place on a non-abrasive surface
(i.e. shipping box) to avoid scratching.
• We recommend an area approx 4’x 8’ (1.2 m x 2.4 m) for unobstructed assembling.
• You should not need to use excessive force when assembling components.
5 3 4
7 8
Not to Scale
Ver 3.8/Jul 15-21
1
The Cambridge Raised Planter Box
STEP ONE
1
Lay the Pre-Assembled Side Wall Panel on the floor as shown and align and insert the pre-assembled shelf into the routed hole.
Do the same for the Front and Back Wall Panels as shown.
This is designed to accomodate the attachment of an extension kit
(sold separately).
2
Align and insert the second Pre-Assembled Side Wall Panel as shown.
3
Stand the planter box up. Center the shelf within the side panel posts and fasten the shelf rails to the posts using 8 of the 5/8” (1.6 cm) screws provided through the pre-drilled holes as shown.
1
2
Note Position of Bottom Rails
3
2
The Cambridge Raised Planter Box
The Cambridge Raised Planter Box
STEP O N E ( C O N T ’ D )
4
Fasten the wall panels together using 4 of the 5/8” (1.6 cm) screws provided through the pre-drilled holes on the posts as shown.
5
Fasten the corner brackets to the posts using 8 of the 1 1/2” (4 cm) screws provided through the pre-drilled holes on the brackets as shown.
4
5
STEP T WO
6
Insert the floor support rail into the front and rear walls as shown.
Note the notch at the ends of the floor support rail.
6
The Cambridge Raised Planter Box
3
8
The Cambridge Raised Planter Box
STEP T W O ( C O N T ’ D )
7
Place the four floor panels onto the floor supports as shown.
Note the notches on the one side of the end panels. The notches are to wrap around the posts.
8
Pressure fit the Post Caps into place. Push firmly until they snap into place.
NOTE: If you purchased the Kingsrow Trellis, leave 2 Post Caps off one of the 36" (91 cm) sides to allow the trellis to be mounted.
7
Notch
Notch
4
North America Toll Free Phone: 1 800 282 9346 www.w
earevita.com
A S S E M B LY I N S T R U C T I O N S
The Raised Planter Trellis*
www.wearevita.com
*The Raised Planter Trellis is designed to mount on to our 24” x 36” White Raised Planter Box (sold separately) as shown above.
Please read through before starting assembly.
IMPORTANT: CHECK THE INSIDE OF YOUR POSTS FOR ALL MATERIALS.
Check Box for These Contents
In the event of missing or defective parts please call our customer service department at 1 800 282 9346
(Mon. to Fri. 8:00 AM to
5
:00 PM EST) .
1. Posts (2) - 10941
2. Top and Bottom Rails (2) - 1.5” x 1.5“ x 35.75” - 10942
3. Horizontal Spindles (3) - 1.5” x .875“ x 31” - 10944
4. Vertical Spindles (5) - 1.5“ x .25” x 21“ - 10943
5. 1” Self-Auguring Stainless Steel Screw (4) - 20016
1
2
3
4
Tools You Will Need
• Cordless Drill
5
Not to Scale
General Information
• Read Instructions through carefully before beginning assembly.
• When assembling components, place on a non-abrasive surface
(i.e. shipping box) to avoid scratching.
• We recommend an area approx 5’x 8’ for unobstructed assembling.
• You should not need to use excessive force when assembling component.
Ver 3.8/Jul 15-21 1
S T E P O N E
1
Align and insert the five vertical spindles into the horizontal spindle as shown. Note the spacing between the horizontal rails are to match that of the posts.
2
Align and insert the top and bottom rails as shown.
3
Insert the lattice from step 2 into the routed holes on the posts as shown. Press down on each of the horizontal rails to lock them into place.
2
1
3
NOTE: There are locking tabs located at the ends of the horizontal rails. Once inserted and pushed into the routed holes, they will lock into place.
S T E P T W O
4
Insert the trellis from Step One above onto the 24” x 36”
White Raised Planter as shown. Place the post caps from the planter box onto the top of the trellis.
4
5
5
Secure the trellis into place using the four provided screws at locations shown below:
2
North America Toll Free Phone: 1 800 282 9346 www.
wearevita.com
advertisement
Related manuals
advertisement