Proxima A3300 Projector User Manual
Advertisement
Advertisement
A3100 A3200 A3300
Regulatory models W3220, W3240 and W3260
Declaration of Conformity
Manufacturer: InFocus Corporation, 27500 SW Parkway Ave. Wilsonville,
Oregon 97070 USA
European Office: Louis Armstrongweg 110, 1311 RL Almere, The
Netherlands
We declare under our sole responsibility that this projector conform to the following directives and norms:
EMC Directive 2004/108/EC
EMC: EN 55022
EN 55024
EN 61000-3-2
EN 61000-3-3
Low Voltage Directive 2006/95/EC
Safety: IEC 60950-1: 1 st Edition
Trademarks
DisplayLink is a trademark of DisplayLink Corporation.
Apple, Macintosh, and PowerBook are trademarks or registered trademarks of Apple Computer, Inc. IBM is a trademark or registered trademark of
International Business Machines, Inc. Microsoft, PowerPoint, and Windows are trademarks or registered trademarks of Microsoft Corporation. Adobe and Acrobat are trademarks or registered trademarks of Adobe Systems
Incorporated. DLP® and the DLP logo are registered trademarks of Texas
Instruments and BrilliantColor™ is a trademark of Texas Instruments.
InFocus, In Focus, and INFOCUS (stylized) are either registered trademarks or trademarks of InFocus Corporation in the United States and other countries.
FCC Warning
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and receiver.
--Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
--Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by InFocus Corporation may void authority to operate the equipment.
Canada
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du
Canada.
Agency Approvals
UL, cUL
Other specific Country Approvals may apply. Please see product certification label.
This document applies to regulatory models W3220, W3240, and W3260.
Input ratings: 3.3 - 1.2A (W3220, W3260), 3.9 - 1.4A (W3240)
InFocus reserves the right to alter product offerings and specifications at any time without notice.
1
Table of Contents
Projector and device connector guide
Replacing the projection lamp 34
Important Operating Considerations for Safety
• Place the projector in a horizontal position no greater than 15 degrees off axis.
• Locate the projector in a well-ventilated area without any obstructions to intake or exhaust vents. Do not place the projector on a tablecloth or other soft covering that may block the vents.
• Locate the projector at least 4' (1.2 m) away from any heating or cooling vents.
• Use only InFocus-approved ceiling mounts.
Warning:
To prevent eye injury if the projector is ceiling mounted, wear protective eyewear before opening lamp door. A warning sticker is included with the user documentation. Place this sticker on the lamp door if the projector is mounted on the ceiling.
• Only genuine InFocus lamps are tested for use in this projector.
InFocus is not liable for the performance, safety or certification of any other lamps. The use of other lamps violates the projector warranty and voids all certification marks on this projector.
• Use only the power cord provided. A surge-protected power strip is recommended.
• Refer to this guide for proper startup and shutdown procedures.
• Hg – Lamp contains mercury. Manage in accordance with local disposal laws. See www.lamprecycle.org
.
• In the unlikely event of a lamp rupture, particles may exit through the projector side vents. When the projector is turned on, keep people, food, and drinks out of the "keep out" area under and around the projector, as indicated by the "X" areas below.
2
2’ / 0.6 m m
/ 1
.5 m
3’
/ 1
8’ / 2.4 m
5’
Follow these instructions to help ensure image quality and lamp life over the life of the projector. Failure to follow these instructions may affect the warranty. For complete details of the warranty, see the Warranty Booklet.
Introduction
Your new digital projector is simple to connect, easy to use, and straightforward to maintain. It is a versatile projector that is flexible enough for business presentations and home video viewing too. The A3100/A3200 has native XGA 1024x768 resolution, and the A3300 has WXGA 1280x800 resolution. This guide applies to all products. They are compatible with a wide variety of computers and video devices.
Product specifications
To read the latest specifications on your multimedia projector, be sure to visit our website at www.infocus.com
, as specifications are subject to change.
Accessories
The standard accessories that came with your projector are listed in the included Quick Start Poster/Booklet. Optional accessories can be found on our website at www.infocus.com
or at your retailer or dealer.
Online registration
Register your projector on our website at www.infocus.com/register to activate your warranty and receive product updates, announcements, and registration incentives.
focus (front ring) remote control receiver (IR) zoom (rear ring) lens elevator foot touch keypad elevator foot connector panel remote control receiver (IR) power cord connector
3
Connector panel
The projector provides both computer and video connection options, including:
• VESA computer (2)
• HDMI, for computer (1) and for video (1)
• S-video
• Composite video
• Separate audio inputs for video and computer
• USB DisplayLink connector, for computer audio/video input. This
USB connection also provides slide advance (and mouse control when used with an optional remote control only)
The projector also provides the following connectors:
• Monitor out, to provide an image on your desktop computer as well as on the projection screen
• Audio out, to provide sound for external speakers
• A 5 volt DC output (see below)
It also has an RS-232 connector for serial control. The Command Line
Interface (CLI) specifications and commands are on our website.
NOTE: DisplayLink video and audio is not sent to monitor out and audio out.
5 volt DC output
The 3.5mm mini-jack triggers provide a 5 volt, 2 amp DC output. It provides a constant output while the projector is on. It is designed to provide power for an InFocus LiteShow II wireless device, which allows wireless projection. More information can be found on our website at www.infocus.com
or at your retailer or dealer.
4
audio inj composite video
S-video monitor out
HDMI for video computer audio out
5 volt output security lock RS-232 DisplayLink connector
Positioning the projector
To determine where to position the projector, consider the size and shape of your screen, the location of your power outlets, and the distance between the projector and the rest of your equipment. Here are some general guidelines:
• Position the projector on a flat surface at a right angle to the screen. The projector must be at least 4.9 feet (1.5m) from the projection screen.
• Position the projector within 10 feet (3m) of your power source and within 6 feet (1.8m) of your video device (unless you purchase extension cables). To ensure adequate cable access, do not place the projector within 6 inches (.15m) of a wall or other object.
• If you are installing the projector on the ceiling, refer to the installation guide that comes with the Ceiling Mount Kit for more information. To turn the image upside down, see “Ceiling Mount” on page 30. We recommend using an InFocus authorized ceiling mount.
• Position the projector the desired distance from the screen. The distance from the lens of the projector to the screen, the zoom setting, and the video format determine the size of the projected image.
• The image exits the projector at a given angle. A3100/A3200 image offset is 115% ; A3300 image offset is 112.4%. This means that if you have an image 10’ high, the bottom of the image will be 1.5' (A3100/
A3200) and 1.24' (A3300) above the center of the lens.
10 ft high image
(A3300)
10 ft high image
(A3100 & A3200)
Table 1: (A3100 & A3200)
Range of distance to the screen for a given screen size
Diagonal
Screen Size
(inches/m)
60/1.5
80/2.0
90/2.3
150/3.8
Distance to screen
Maximum distance (feet/ m)
8.6/2.6
11.5/3.5
12.9/3.9
21.5/6.6
Minimum
Distance
(feet/m)
7.8/2.4
10.4/3.2
11.7/3.6
19.5/5.9
Table 2: (A3300)
Range of distance to the screen for a given screen size
Diagonal
Screen Size
(inches/m)
60/1.5
80/2.0
90/2.3
150/3.8
Distance to screen
Maximum distance (feet/ m)
7.3/2.2
9.7/2.9
10.9/3.3
18.1/5.5
Minimum
Distance
(feet/m)
6.5/2.0
8.7/2.7
9.8/3.0
16.3/5.0
bottom of image
1.24 ft above center of lens lens center
Projection angle bottom of image
1.5 ft above center of lens lens center
Projection angle
5
Projector and device connector guide
The following illustration and table should help you find the connectors to use and obtain the best resolution possible from your input devices, such as computers, standard VCRs, DVD players (progressive and interlaced),
HDTV sources (1080i, 1080p and 720p HDTV formats), TV and satellite tuners, camcorders, video games (progressive and interlaced), and laser disc players.
audio inj composite video monitor out
HDMI for video computer
S-video audio out
5 volt output security lock RS-232
DisplayLink connector
6
Video Device
Video
Compatibility
If Your Device
Connector Is
Attach to Adapter or Labeled
Connector on
Projector
For Setup Instructions, see Comments
Standard Broadcast TV (not
HDTV) via: cable, digital cable, satellite TV, DVD, or
VCR
NTSC, PAL, and
SECAM formats
Composite video or S-video
Video 3 or Video 2
Composite video connection on page 13.
Not for progressive
(i.e. HDTV) sources.
See page 8.
Standard Video Camera
NTSC, PAL, and
SECAM formats
Composite video or S-video
Video 3 or Video 2
Standard Video Game
NTSC, PAL, and
SECAM formats
Composite video or S-video
Video 3 or Video 2
Composite video connection on page 13.
Not for progressive
(i.e. HDTV) sources.
See page 8.
Composite video connection on page 13.
Not for progressive
(i.e. HDTV) sources.
See page 8.
7
Video Device
HDTV
(High Definition TV)
Progressive DVD
Progressive Video Game
Video
Compatibility
1080i, 1080p, 720p
Component 480i
If Your Device
Connector Is
VGA
Component video
Attach to Adapter or Labeled
Connector on
Projector
Computer 3 or
Computer 2
Computer 3 or
Computer 2 via optional VESA to
Component adapter
HDMI
For Setup Instructions, see
Component video connection on page 13
HDMI connection on page 13
Comments
1080i, 1080p, 720p
Component 480p and 480i
VGA
Component video
Computer 3 or
Computer 2
Computer 3 or
Computer 2 via optional VESA to
Component adapter
HDMI
Component video connection on page 13
HDMI connection on page 13
1080i, 1080p, 720p
Component 480p and 480i
VGA
Component video
Computer 3 or
Computer 2
Computer 3 or
Computer 2 via optional VESA to
Component adapter
HDMI
8
Component video connection on page 13
HDMI connection on page 13
Connecting a computer source
Required computer connections (DisplayLink or VESA)
If your computer has Windows XP SP2 or newer*, connect the USB cable between your computer's USB port and the projector's DisplayLink connector , then follow the instructions on the screen. See the DisplayLink
Manager User's Guide for more information.
* For the latest information about support for other operating systems
(including Apple), go to www.infocus.com/support/displaylink
Or, connect one end of the provided computer cable to the Computer 2 or
Computer 3 connector on the projector and the other to the VESA connector on your computer. If you are using a desktop computer, you will need to disconnect the monitor cable from the computer’s video port first
(you can connect this monitor cable to the Monitor Out connector on the projector, see below).
Connect the black power cord to the Power connector on the side of the projector and to your electrical outlet. The Power light on the Status
Indicator Panel (page 14) turns amber.
NOTE : Always use the power cord that shipped with the projector.
Optional computer connections
To get sound from the projector, connect an audio cable (optional cable, not included) to your computer and to the Audio In Computer connector on the projector. You may also need an adapter.
If you are using a desktop computer and want to see the image on your computer screen as well as on the projection screen, connect the computer’s monitor cable to the Monitor Out connector on the projector.
NOTE : DisplayLink video and audio is not sent to monitor out and audio out.
To advance slides in a PowerPoint presentation using the remote control, plug the USB cable into the USB mouse connector on your computer and the DisplayLink connector on the projector.
9
connect USB cable connect computer cable connect power cord connect audio cable connect monitor cable
MOLEX
MOLEX
Displaying an image
Touch the Power button.
The Power button blinks green and the fans start to run. When the lamp comes on, the start up screen displays and the Power button is steady green.
It can take a minute for the image to achieve full brightness.
? No start up screen?
press Power button
Turn on your computer or video device.
The image should appear on the projection screen. If it doesn’t, press the
Source button on the projector’s keypad or remote.
If you are using a VESA cable to connect your computer to the projector (instead of DisplayLink):
If using a laptop, make sure its external video port is active.
Many laptops do not automatically turn on their external video port when a projector is connected. Usually a key combination like FN + F8 or CRT/
LCD key turns the external display on and off. Locate a function key labeled
CRT/LCD or a function key with a monitor symbol. Press FN and the labeled function key simultaneously. Refer to your laptop’s documentation to learn your laptop’s key combination .
? No laptop image?
Try pressing the Auto Image button on the
? Is your laptop connected to the projector's DisplayLink connector?
See the InFocus DisplayLink Manager User's Guide for troubleshooting information.
turn on computer or video device activate laptop’s external port monitor key or
LCD/CRT key
FN key
10
Adjusting the image
If necessary, adjust the height of the projector by pressing the elevator foot release button to extend the foot.
If necessary, rotate the leveling foot located at the rear of the projector.
Avoid placing your hands near the hot exhaust vent at the side of the projector.
Position the projector the desired distance from the screen at a 90 degree angle to the screen.
See page 5 for a table listing screen sizes and distances.
adjust height adjust distance release button elevator foot
Adjust the zoom or focus.
adjust zoom or focus
If the image is not square, first make sure that the projector is perpendicular to the screen. If the image is larger or smaller on the top or bottom edge of the screen, press the top Keystone button to reduce the upper part of the image, and press the bottom Keystone button to reduce the lower part.
If the left or right side of the screen is larger or smaller the other, you can turn the projector to the left or to the right a few degrees to square the image.
Adjust the Contrast or Brightness in the Basic Picture menu. See page 28 for help with these menu adjustments.
For Aspect Ratio, keep in mind that DVD players must be configured for
16:9 in order to view the highest quality image. For more information
regarding Aspect Ratio, see page 12.
zoom (rear ring) adjust keystone adjust Basic Picture menu
11
focus (front ring)
Connecting a video device
You can connect video devices such as VCRs, DVD players, camcorders, digital cameras, video game consoles, HDTV receivers, and TV tuners to the projector. You can connect the audio directly to the projector to get sound from the built-in speaker, or you can bypass the projector’s audio system and connect the audio directly from your source to a stereo or home theater system.
You can connect the projector to most video devices that can output video.
You cannot directly connect the coaxial cable that enters your house from a cable or satellite company, the signal must pass through a tuner first.
Examples of tuners are digital cable boxes, VCRs, digital video recorders, and satellite TV boxes. Basically, any device that can change channels is considered a tuner.
Before connecting your projector, you should decide which aspect ratio you want to use. The projector’s Aspect Ratio setting is accessed through the
Resize button on the remote or through the projector’s Basic Picture Menu.
See page 28 for more information.
What is Aspect Ratio?
Aspect ratio is the ratio of the image width to image height. TV screens are usually 4:3. HDTV and most DVDs are 16:9. If you’re projecting onto a screen, the size/shape of the screen may determine which aspect ratio to use. If you are projecting onto a blank wall, you don’t have the screen size restriction. What you plan to project will also help you choose between 4:3 and 16:9. Most TV shows are 4:3, while most movies are 16:9.
If you have a 16:9 screen then you should select an aspect ratio of 16:9 for anamorphic movies or HDTV, and Native for 4:3 content. If you have a 4:3 screen you should still use 16:9 for anamorphic movies or HDTV, but you also have the option of using either 4:3 (to fill the screen) or Native (for direct pixel mapping) for 4:3 content. Keep in mind that anamorphic movies only appear correctly if the DVD player is set to output to a 16:9 television.
4:3 screen
12
4:3 screen
Do Not Use
4:3 mode
16:9 mode
Native mode
(NTSC only)
Video device connections
No video cables are provided with the projector. You can order cables from
InFocus or provide your own.
Composite video connection
Plug the composite video cable’s yellow connector into the video-out connector on the video device. Plug the other yellow connector into the yellow Video 3 connector on the projector.
Plug the white connector of a Mini-plug audio Y-cable into the left audio out connector on the video device and plug the red connector into the right audio out connector on the video device. Plug the other end of the cable into the Audio In Video connector on the projector.
Keep in mind that video output from composite connections is not as high quality as S-video.
HDMI 1.3 connection
HDMI is a standard, uncompressed, all-digital audio/video interface.
HDMI provides an interface between sources, such as set-top boxes, DVD players, and receivers and your projector. Plug an HDMI cable into the video-out connector on the video device and into the HDMI connector on the projector.
To take advantage of HDMI 1.3 Deep Color (30 bit) you must have a 1.3compatible source.
S-video connection
If your video device uses a round, four-prong S-video connector, plug an Svideo cable into the S-video connector on your video device and into the
Video 2 connector on the projector. Use the audio cable as described above.
Keep in mind that S-video delivers higher quality video output than composite.
VESA connection
If your video device has a 15-pin VGA output, plug one end of the included computer cable into the VGA connector on your video source. This connector may be labeled “To Monitor” on the video source. Plug the computer cable into the Computer 3 or Computer 2 connector on the projector.
Component video connection
If your HD video device has component connectors, an optional
Component to VESA adapter can be used. Plug the component cable into the video device. Plug the other end of the component cable into the adapter and plug the adapter into the Computer 3 or Computer 2 connector.
Component offers the highest quality video output.
13
Shutting down the projector
The projector automatically displays a black screen after no active source is detected for 30 minutes. This black screen helps preserve the life of the projector. The image returns when an active source is detected or a remote or keypad button is pressed.
Screen Save Time
You can make the black screen appear after a preset number of minutes by turning on the Screen Save Time feature in the Setup menu. See page 30.
Auto Off Time
The projector also has an Auto Off Time feature that automatically turns the projector off after no active sources are detected and no user interaction with the projector is performed for 30 minutes. By default, this feature is off.
You can change the length of time, see page 30.
Turning off the projector
To turn the projector off, press the Power button on the remote or keypad.
The lamp turns off and the LED blinks amber for 1 minute while the fans continue to run to cool the lamp. When the lamp has cooled, the LED lights amber and the fans stop. Unplug the power cable to completely power off the projector.
Troubleshooting your setup
If your image appears correctly on the screen, skip to the next section. If it does not, troubleshoot the setup.
The Status Indicator Panel on top of the projector indicates the state of the projector and can help you troubleshoot.
Table 3: Status indicator light behavior and meaning
Icon
Power, solid amber
Meaning
The projector is plugged in.
Power, blinking green
Power, solid green
Power, blinking amber
Thermometer
Lamp
Wrench/Service
The power button has been pressed and the software is initializing.
The projector is on and initialized.
The power button has been pressed to turn the projector off and the fans are running to cool the projector.
The projector is too hot. Make sure the
vents aren’t blocked (see page 20). Turn
off the projector and wait one minute, then turn the projector on again. Contact
Technical Support if the problem persists.
Visit www.infocus.com/support to contact service.
Turn off the projector and wait one minute, then turn the projector on again.
If the lamp light turns on again, replace the lamp and reset the lamp timer.
Turn off the projector and wait one minute, then turn the projector on again.
If the service lamp turns on again, service is required. Visit www.infocus.com/ support to contact service.
14
Problem
No start up screen
A
Only start up screen appears
Startup
Screen
A
Solution
Plug power cord into the projector press power button
Result
Correct image
Startup
Screen
If your computer is using the projector's
DisplayLink connector, see the DisplayLink
User's Guide for troubleshooting information.
Press the Source button activate laptop’s external port
Computer image projected
A
A
Restart laptop
15
Problem
No computer image, just the words “Signal out of range”
Solution
Press the Auto Image button on keypad adjust computer refresh rate in Control Panel > Display >
Settings > Advanced > Adapter (location varies by operating system)
Signal out of
the range
Result
Computer image projected
A
A
A
You may also need to set a different resolution on your computer, as shown in the following problem, “image fuzzy or cropped”
Only my laptop’s background appears, not the
Desktop icons
A
If your computer is using the DisplayLink connector, use DisplayLink Manager software to change the display mode from Extended Desktop to Duplicated Desktop.
See the DisplayLink Manager User's Guide for more information.
Disable “Extend my Windows Desktop” in Control
Panel > Display > Settings > Display 2 (location varies by operating system)
Background and Desktop projected
A
A
A
Uncheck this option, then click Apply
16
Problem
Image fuzzy or cropped
A
A
Image not centered on screen
Solution
Set your computer’s display resolution to the native resolution of the projector (Start >
Settings > Control Panel > Display > Settings tab)
Result
Image clear and not cropped
A
For a laptop, disable laptop monitor or turn-on dualdisplay mode
Move projector, adjust zoom, adjust height
A
Correct image
Adjust horizontal or vertical position in Advanced
Picture menu
17
Problem
Image not square
Image not sharp
Solution
Adjust Keystone on keypad
Adjust Sharpness in the Basic Picture menu
Result
Square image
Correct image
Image does not fit 4:3 or 16:9 screen Change aspect ratio to 4:3 or 16:9 in Basic
Picture>Aspect ratio menu
Correct image
18
Problem
Image upside down A
Image reversed left to right
A
Projected colors don’t match source
Solution
Turn off Ceiling Mount in Setup menu
Turn off Rear Project in Setup menu
Result
Correct image
Correct image
COLOR
Adjust color, tint, brightness, contrast in the
Basic Picture menu
Correct image
COLOR
19
Problem
The video embedded in my PowerPoint presentation does not play on the screen
A
A
B
Solution
If your computer is using the projector's
DisplayLink connector, see the DisplayLink
User's Guide for video troubleshooting information.
Turn off the internal LCD display on your laptop
Result
Embedded video plays correctly
A
B
A
B
Lamp won’t turn on, Temperature light is on Make sure vents aren’t blocked, turn off the projector and allow it to cool for one minute
Lamp turns on
A Startup
Screen
Temperature light
20
Problem
“Replace lamp” message appears at startup, lamp won’t turn on, Lamp light is turned on
Solution
Lamp must be replaced (see page 34)
lamp door
A
Lamp light
Result
Lamp turns on
Startup
Screen replace lamp
Still need assistance?
If you need assistance, visit our website at www.infocus.com/service or call us. Check out our HOW TO section there for additional information on using this projector for home theater or gaming applications. See the Quick
Start Poster/Booklet for support contact information.
This product is backed by a limited warranty. An extended warranty plan may be purchased from your dealer. When sending the projector in for repair, we recommend shipping the unit in its original packing material, or having a professional packaging company pack the unit. Please insure your shipment for its full value.
21
Using the remote control
The remote uses two (2) provided AA batteries. They are easily installed by removing the cover from the remote’s back, aligning the + and - ends of the batteries, sliding them into place, and then replacing the cover.
Caution : When replacing the batteries, be aware that using batteries other than the type provided with the projector may risk severe damage to the remote. When disposing of the batteries, be sure to do so in an environmentally proper manner.
To operate, point the remote at the front of the projector (not at the computer). The range of optimum operation is about 15 feet (4.5m).
Press the remote’s Power button to turn the projector on and off (see
Press the remote’s Menu button to open the projector’s menu system. Use the arrow buttons to navigate, and the Select button to select features and
adjust values in the menus. See page 27 for more info on the menus.
The remote also has a Source button to switch between sources.
The remote also has:
• Volume buttons to adjust the sound.
• Custom button that can be assigned to a special function, like Blank
Screen or Freeze (see page 30).
• Source button to switch between sources.
• Blank button to blank the screen.
• Presets button to select stored settings (see page 28).
• Mute button to silence the audio.
• Auto Image button to resynch the projector to the source
• Resize button to switch among aspect ratios (see page 28).
Troubleshooting the remote
• Make sure the batteries are installed in the proper orientation and are not dead.
• Make sure you’re pointing the remote at the projector or the screen, not the computer, and are within the remote range of 15 feet (4.5m). For best results, point the remote at the projector.
22
navigation buttons
Using the audio
Using the projector’s speakers
When the computer is using the DisplayLink connector, both audio and video are sent over the USB cable to the projector and audio will play from the projector's speakers.
For inputs other than DisplayLink, to use the projector's speakers, connect the audio source to the Audio In Computer or Video connectors.
To adjust the volume, press the Volume buttons on the keypad or remote.
Troubleshooting Audio
If you aren’t hearing the audio, check the following:
• If your computer is using the projector's DisplayLink connector, see the
InFocus DisplayLink Manager User's Guide for audio troubleshooting information
• Make sure the audio cable is connected to the correct Audio In connector, Computer or Video.
• Make sure the volume is turned up enough. Press the Volume button on the keypad or remote.
• Make sure the correct source is active.
• Make sure that you are connected to an “audio out” connector on the source as opposed to a “line-in” or “microphone” connector.
• Adjust the audio source.
• If playing a video, make sure the playback has not been paused.
Connecting external speakers
The projector can be attached to external amplified speakers by connecting a 3.5mm stereo audio cable from the Audio Out connector on the projector to the amplified speakers. Alternatively, you can bypass the projector’s audio system and connect the audio directly from your source to a stereo or home theater system.
connect audio cable connect audio cable external speakers with own power source
23
speaker cable audio out
Using the keypad buttons
Most buttons are described in detail in other sections, but here is an overview of their functions:
Power
–turns the projector on and off (page 10).
Auto Image –resets the projector to the source.
Presets –cycles through the available preset settings (page 28).
Keystone
–adjusts squareness of the image (page 11).
Menu
–opens the on-screen menus (page 27).
Select
–confirms choices made in the menus (page 27).
Up/Down arrows
–navigates to and adjusts settings in the menus (page 27).
Volume
Source
–changes the active source (page 10).
menu navigation buttons
24
Optimizing computer images
After the projector is running and the image is on the screen, you can optimize the image using the onscreen menus. For general information on
• Adjust the Keystone, Contrast, or Brightness in the Basic Picture menu
(page 28).
• Change the Aspect Ratio. Choose the option that best fits your input source (page 28).
• Adjust the Color Temperature in the Advanced Picture menu
(page 28).
• Adjust the Phase, Tracking, or Horizontal or Vertical position in the
Advanced Picture menu (page 29).
• Once you have optimized the image for a particular source, you can save the settings using Presets. This allows you to quickly recall these settings later (page 28).
• If your computer is using the projector's DisplayLink connector, see the
InFocus DisplayLink Manager User's Guide for information about optimizing images.
Presentation features
Several features are provided to make giving presentations easier. Here is an overview, details are found in the menu section.
• The Custom key allows you to assign various features to the button.
The default effect is Source Info, which displays information about the projector and current source. See page 30 for details.
• The Startup Screen option lets you change the default start up screen to a blank or default screen (page 31).
• Two options, Auto Off and Screen Save Time, are provided to automatically shut down the projector after several minutes of inactivity or display a black screen. This helps preserve lamp life
(page 30).
25
Optimizing video images
After your video device is connected properly and the image is on the screen, you can optimize the image using the onscreen menus. For general
information on using the menus, see page 27.
• Adjust the Keystone, Contrast, Brightness, Color, or Tint in the Basic
Picture menu (page 28).
• Change the Aspect Ratio. Choose the option that best fits your input source (page 28).
• Select a Sharpness setting (page 28).
• Adjust the Color Temperature. Select a listed warmth value (page 29).
• Turn on Overscan to remove noise on the edges of the image (page 29).
Customizing the projector
You can customize the projector for your specific setup and needs. See
page 30 to page 31 for details on these features.
• For rear projection, turn Rear Project on in the Setup menu.
• For ceiling mounted projection, turn Ceiling Mount on in the Setup menu.
• For ceiling mounted projection, turn Ceiling Mount on in the Setup menu.
• Specify which source the projector checks first for active video during power-up.
• Specify the function of the Custom key on the remote.
• Turn the projector’s display messages on and off.
• Turn on power saving features.
• Specify blank screen colors and start up logos.
• Specify the language viewed on the menus.
• Save settings for the active source as a preset.
26
Using the menus
To open the menus, press the Menu button on the keypad or remote. (The menus automatically close after 60 seconds if no buttons are pressed.) Use the arrow buttons to move up and down to highlight the desired menu, then press the Select button.
To change a menu setting, highlight it, press Select , then use the up and down arrow buttons to adjust the value or select an option or turn the feature on or off. Press Select to confirm your changes. Use the arrows to navigate to another setting. When your adjustments are complete, press
Menu to access a different menu; press the Menu button at any time to navigate to the higher-level menu and ultimately close the menus.
The menus are grouped by usage:
• The Basic Picture menu provides common image adjustments.
• The Advanced Picture menu provides more complex image adjustments.
• The Setup menu provides set-up type adjustments that are not changed often.
• The Status and Service menu provides information about the projector and source.
Basic Picture menu keypad navigation buttons
Advanced Picture menu
27
Setup menu Status and Service menu
Basic Picture menu
To adjust the following settings, highlight the setting, press Select , use the up and down arrows to adjust the values, then press Select to confirm the changes.
Brightness : changes the intensity of the image.
Contrast : controls the degree of difference between the lightest and darkest parts of the picture and changes the amount of black and white in the image.
Sharpness : (video sources only) changes the clarity of the edges of a video image. Select a sharpness setting.
Color : adjusts a video image from black and white to fully saturated color.
The color setting applies to video sources only.
Tint : adjusts the red-green color balance in the image of NTSC video images. The tint setting applies to NTSC video sources only.
Aspect Ratio : Aspect ratio is the ratio of the image width to image height.
TV screens are usually 4:3. HDTV and most DVDs are 16:9.
Select Auto to have the projector choose the ratio. Choose Native to see the unmodified input with no resizing by the projector. Select 16:9 to watch enhanced widescreen DVDs.
For more information regarding Aspect Ratio, see page 12.
Apply Preset...
: Presets are provided that optimize the projector for displaying computer presentations and video images under certain conditions.
There is also a user-definable preset. To set this preset, adjust the image and select Save User in the Presets menu. You can recall these settings in the future by selecting the User preset.
Keystone : adjusts the image vertically and makes a squarer image. You can also adjust keystone from the keypad.
Digital Zoom : changes the size of projector’s display area. If the display area has been resized by this setting, it can be moved by changing the Horz
Shift and Vert Shift settings.
Horz Shift/Vert Shift : moves the display area horizontally or vertically if its size has been changed by the Digital Zoom setting.
28
Basic Picture menu increasing keystone
Aspect ratio decreasing keystone
Advanced Picture menu
BrilliantColor™ : produces an expanded on-screen color spectrum that delivers enhanced color saturation for bright, true-to-life images. Choose
Normal Look for most video sources and Bright Look for most computer sources.
White Peaking : (video sources only) increases the brightness of whites that are near 100%.
Color Temperature : changes the intensity of the colors. Select a listed relative warmth value.
Force wide : when this is off, the analog locking algorithms choose the standard mode resolution (4:3) as the preferred default resolution. When this is on, the analog locking algorithms choose wide mode resolution
(16:10) as the preferred default resolution.
Overscan : removes noise around the video image.
Phase : adjusts the horizontal phase of a computer source.
Sync Threshold : (progressive signals only) If a hardware device, such as a
DVD player, is not syncing properly with the projector, select this option to help it to sync when connected to the projector.
Tracking : adjusts the vertical scan of a computer source.
Color Space : This option applies to computer and component video sources. It allows you to select a color space that has been specifically tuned for the input signal. When Auto is selected, the projector automatically determines the standard. To choose a different setting, turn off Auto, then choose RGB for computer sources or choose either REC709 or REC601 for component video sources.
Gamma : select the appropriate gamma from among Video, Film, Bright, and CRT.
Horizontal/Vertical Position : adjusts the position of a computer source.
29
Advanced Picture menu
Setup menu
Language : allows you to select a language for the onscreen display.
Key Click : turns the key click sound on or off. When this setting is on, pressing keys on the keypad causes the projector’s speaker to play a “click” sound.
Custom Key : allows you to assign a different function to the Custom button, allowing you to quickly and easily use the effect. Highlight an effect and press Select to choose a different one.
• Source Info : the default action. Shows the Source Info menu.
• Projector Info : Shows the Projector Info menu.
• Aspect Ratio
: toggles among 4:3, 16:9, and Native (see page 12 and
page 28).
• Auto Image
: resets the projector to the source (page 24).
• Overscan : removes noise around the image.
• Blank Screen : displays an empty screen.
• Freeze Screen : pauses the projected image.
• Mute : turns off all sound.
• Source : cycles through available sources.
AC Power On : When this feature is on, the projector automatically turns on when electrical power is connected. This allows control of ceiling mounted projectors with a wall power switch.
Auto Off Time : automatically turns the projector off after no signals are detected for a preset number of minutes. If an active signal is received before the projector powers down, the image will be displayed.
Screen Save Time : automatically blanks the screen with a black color after no signals are detected for a preset number of minutes. The image returns when an active source is detected or a remote or keypad button is pressed.
Lamp Low Power : toggles between on and off. Turn it on to lower the light output of the lamp. This also lowers the fan speed, making the projector quieter.
Power Sounds : controls whether the projector makes a sound when powered on and off.
30
Auto Source : When this feature is On, the projector automatically finds the active source, checking the selected Power-up Source first. When this feature is Off, the projector defaults to the source selected in Power-up
Source. To display another source, you must manually select one by pressing the Source button on the remote or keypad.
Setup menu
Power-up Source : determines which source the projector checks first for active video during power-up.
HDMI DDC : When this feature is set to On, the projector will support an older DVD player for HDMI port.
Video Standard : When this feature is set to Auto, the projector attempts to automatically pick the video standard based on the input signal it receives.
(The video standard options may vary depending on your region of the world.) If the projector is unable to detect the correct standard, the colors may not look right or the image may appear “torn.” If this happens, manually select a video standard by selecting NTSC, PAL, or SECAM from the Video Standard menu.
Closed Captions : controls closed caption display while audio is not muted.
If this setting is not off, and audio is not muted, and the source is NTSC and contains captions on the selected channel, then the projector must display caption text overlaid on the image.
Ceiling Mount : turns the image upside down for ceiling-mounted projection.
Rear Project : reverses the image so you can project from behind a translucent screen.
Auto Keystone : automatically adjusts vertical image.
Prevent PC Screen Saver : prevents your computer from going into Screen
Save mode. The projector must be connected to the PC via a USB cable for this feature to work.
Startup Screen : allows you to display a blank screen instead of the default screen at startup, and when no source is detected.
Take Snapshot...
: Captures the current image and allows it to be used as the startup screen image.
Blank Screen Color : determines what color is displayed when you press the Blank button on the remote.
Blank Screen Style : Select Solid, Timer, or Test Patterns. The Timer option is useful for classroom tests or break times during meetings.
Show Messages : displays status messages (such as “Searching”) in the lower-left corner of the screen.
Menu Offset : allows you to change the position of the On Screen Display items.
Menu Transparency : allows you to change how much of the projected image behind the menu you can see. As the value increases, more of the image behind the menu is visible.
Magnify Controls : determines whether the select key can be used to change magnify settings when the OSD menu is not visible.
PIN Protect : The PIN (personal identification number) feature allows you to password protect your projector. Once you enable the PIN feature, you must enter the PIN before you can project an image. The default PIN on this projector is Menu-Up-Down-Select-Source . Use the navigation buttons on the remote or keypad to enter the correct 5-button press sequence. When all
5 numbers are entered correctly, press the Select button on the remote or keypad to select OK. If the message “Wrong PIN” appears, verify the code
31
and re-enter it. If you mis-enter a number, you must enter 5 numbers and press the Select button in order to access the “Wrong PIN” message and reenter the code.
To enter the PIN at projector startup:
Power up the projector. The “Enter PIN” dialog box appears after the startup screen. Enter the PIN. Use the navigation buttons on the remote or keypad to enter the correct button press sequence. See the description above for instructions.
To change the PIN:
Select “Change PIN...” in the Setup menu. Enter the existing PIN. Enter the new PIN. You can navigate between OK and Cancel by pressing the up and down buttons on the keypad. Select OK or Cancel by pressing the Select button. Verify the new PIN.
If you lose or forget your custom PIN:
Contact InFocus support. Go to www.infocus.com/support
Serial Port, Baud Rate : selects the serial port and baud rate.
Serial Port Echo : controls whether the serial port echoes characters.
Status and Service menu
Source Info : a read-only display of current source settings.
Projector Info : a read-only display of current projector settings.
Reset Lamp Hours : resets the lamp hours used counter in the Projector Info menu to zero. Do this only after changing the lamp.
Factory Reset : restores all settings to their default.
Service Code : only used by authorized service personnel.
Status and Service menu
32
Maintenance
Cleaning the lens
1
Apply a non-abrasive camera lens cleaner to a soft, dry cloth.
• Avoid using an excessive amount of cleaner, and don’t apply the cleaner directly to the lens. Abrasive cleaners, solvents or other harsh chemicals might scratch the lens.
2
Lightly wipe the cleaning cloth over the lens in a circular motion.
Using the security lock
The projector has a security lock for use with a PC Guardian Cable Lock
System. Refer to the information that came with the lock for instructions on how to use it.
33
security lock
Replacing the projection lamp
The lamp hours used timer in the Projector Info menu counts the number of hours the lamp has been in use. Twenty hours before the lamp life expires, the message “Change lamp” appears on the screen at startup.
• NOTE : You can order new lamps from www.infocus.com
(in select areas), your retailer or your dealer. Only genuine InFocus lamps are tested for use in this projector. InFocus is not liable for the performance, safety or certification of any other lamps. The use of other lamps violates the projector warranty and voids all certification marks on this projector.
1
Turn off the projector and unplug the power cord.
2
Wait 60 minutes to allow the projector to cool thoroughly.
3
Remove the lamp door by (a) removing the screw on the side of the lamp door, (b) sliding the door forward, and (c) lifting the door off.
WARNINGS :
• To avoid burns, allow the projector to cool for at least 60 minutes before you replace the lamp.
• Only genuine InFocus lamps are tested with this projector. Use of other lamps may cause electrical shock and fire.
• Unplug the power cord before replacing the lamp.
• Do not drop the lamp module. The glass may shatter and cause injury.
• Do not touch the glass lamp screen. Fingerprints can obscure projection sharpness.
34
(c)
(a)
Lamp hours turn off and unplug projector wait 60 minutes
(b)
• Be extremely careful when removing the lamp housing. In the unlikely event that the lamp ruptures, small glass fragments may be generated.
The lamp module is designed to contain most of these fragments, but use caution when removing it. Before replacing a ruptured lamp, clean the lamp compartment and dispose of cleaning materials. Wash hands after lamp replacement. If replacing the lamp while the projector is ceiling-mounted, wear protective eyewear.
Hg – Lamp contains mercury. Manage in accordance with local disposal laws. See www.lamprecycle.org
.
4
Loosen the captive screw that attaches the lamp housing to the projector. Carefully remove the lamp housing. Dispose of the lamp in an environmentally proper manner.
5
Install the new lamp housing and tighten the screw.
6
Re-attach the lamp connector to the projector.
7
Replace the lamp door by sliding it into place.
8
Plug in the power cord and press the Power button to turn the projector back on.
9
To reset the lamp hour timer, navigate to the Status and Service menu and select Reset Lamp Hours . See page 32 for details.
loosen screw
35
INDEX
Numerics
A
B
C
Connecting
customer service contact information 21
36
D
DVDs 28
F
G
H
I
Image
K
L
laptop video port activation 10
M
O
P
Power connector 9 power cord 9
Projector
offset 5
shutting down 14 troubleshooting problems 14
R
S
37
shutting down the projector 14
speakers, connecting external 23
T
U
V
W
Z
Download
Public link updated
The public link to your chat has been updated. You may view and manage your chat links after registration here.
Document public link
Advertisement